Search Results

Search found 1464 results on 59 pages for 'blocking'.

Page 33/59 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

• ASA5500 series logging for management interface in transparent mode

  - by ANervousTwitch

  i have a cisco asa5520 in transparent mode. the interface is on the same subnet as some windows machines, which are generating a lot of broadcast traffic that is filling up the logs. is there any way to have it not log that its blocking those packets? its a bunch of these messages: "through-the-device packet to from management-only network is denied: udp src..." im also seeing some of those zeroconf requests that id like to drop logging for. i tried to just put a rule on the management interface, but apparently thats not allowed.

  Read the article

• Problem with PPTP VPN and internet

  - by Enriquev

  Hello, I have an internet connection the following way : Internet Modem <- FireWall(not a router, a firewall) <- PC Everything is setup so my pc has an external ip address, and my firewall takes care of blocking bad stuff. I connect by VPN to an external network, so I added a new connection using Windows Xp's "New connection wizard" (the vpn client that comes with Windows XP), it's a PPTP connection so I used all default settings. I put the PPTP server's IP, my username and password and I succesfully connected. I was able to have access to the external VPN ressources. The only problem is everytime I connect to this VPN, my computer cannot connect to the web anymore, no msn, no ping, no web. Is there anything special I should be doing?

  Read the article

• Remote Software Solution that Acts as a Client

  - by Richard

  I am looking for something that I am not sure exists. I have a remote computer that will not allow incoming traffic due to ISP blocking of ports(basically double NAT situation that I am unable to get around). I am wondering if I have a computer acting as a client, is there any solution out there that will allow remote access to the computer. I do have other servers on the net that have static IP's that the computer could initiate a connection with. I am thinking of using Debian Linux, However computer is not built yet so OS is not overly important at this point.

  Read the article

• Using unsigned drivers in Windows 8

  - by T. Fabre

  I just migrated from Windows 7 x64 to 8, but I can't get my VPN software to run anymore : the SafeNet IKE service (installed by SafeNet SoftRemoteLT GA, used by my VPN provider) cannot start anymore. I found that by default unsigned drivers are disabled on Win8, and that is what is blocking the driver. The System event log tells me that the driver (apparently, C:\WINDOWS\SysWow64\Drivers\IPSECDRV.sys ) was blocked when I try to manually start the service (SafeNet IKE Service). I get the same messages for another driver, crypto.sys found in the same folder. I tried using bcdedit to enable unsigned drivers : bcdedit /set loadoptions DDISABLE_INTEGRITY_CHECKS bcdedit /set testsigning ON After reboot, same error. I tried by booting into Win 8's test mode, same issue. Applying the code signing policy (Enabled, Ignore) does not help either. Running gpresult does show that the policy is applied. Any help welcome.

  Read the article

• Blocked port 25 on Windows 7 64 bit

  - by Michal Gow

  Strange problem. I have 2 computers connected to Wifi router. One with Windows Vista & second with 2 operating systems: SUSe Linux and Windows 7 64bit on it. Computer with Vista can connect to SMTP server of my email provider (and any other) using port 25, and can connect to a mail server using telnet mail.server.com 25 if this port is open. Computer with dual operating system can (using Linux) do the same. The same computer, with the same hardware (Wifi card etc.), and using the same WiFi router, cannot however use Port 25 and cannot Telnet into any smtp server. So the problem is in Windows 7. I did uninstall all antivirus software and disabled the firewall. The problem is still here. Is there way how find out which software is blocking this port?

  Read the article

• Windows 7 blocks network access to network-installed apps

  - by VokinLoksar

  Windows 2008 R2 domain. Users, running Windows 7 Enterprise, are trying to run some software from a network share. Specifically, I've tested this with MATLAB and PuTTY. When starting, MATLAB has to contact a licensing server to get its license. This action fails for regular users when they start MATLAB from the network share. However, if they copy the installation directory to a local disk everything works fine. Running MATLAB as an admin user from the network share also works. Same story with PuTTY. If the executable is launched from the share, regular users cannot connect to any servers. Something is blocking network communications for programs that are launched from a network drive. Here's the only other mention I could find of the same problem: https://social.technet.microsoft.com/Forums/en-US/w7itpronetworking/thread/4504b192-0bc0-4402-8e00-a936ea7e6dff It's not the Windows firewall or the IE security settings. Does anyone have any clue as to what this is?

  Read the article

• Recurring network issues the same time every day.

  - by Peter Turner

  Something has been happening on my company's network at 9:30 every day. I'm not the sysadmin but he's not a ServerFault guy so I'm not privy to every aspect of the network but I can ask questions if follow up is needed. The symptoms are the following : Sluggish network and download speed (I don't notice it, but others do) 3Com phones start ringing without having people on the other end. We've got the following ports exposed to the public for a web server, a few other ports for communicating with our clients for tech support and a VPN. We've got a Cisco ASA blocking everything else. We've got a smallish network (less than 50 computers/vms on at any time). An Active Directory server and a few VM servers. We host our own mail server too. I'm thinking the problem is internal, but what's a good way to figure out where it's coming from?

  Read the article

• Allowing outbound traffic with APF/iptables for OpenVZ container

  - by David

  I have apf installed on a OpenVZ container (proxmox 2.1). The config is pretty much vanilla and things are working. My external services like ssh and http are working. My problem is that all outbound traffic on http/https is blocked. How do I allow all outbound traffic for http/https. If I change EGF to 1 like this, all inbound and outbound traffic gets blocked EGF="1" EG_TCP_CPORTS="21,25,80,443,43,53" EG_UDP_CPORTS="20,21,53" EG_ICMP_TYPES="all" I opened a single outbound rule with the following # /usr/local/sbin/apf -a downloads.wordpress.org How do I allow all outbound traffic on http/https without blocking all traffic? Why would I allow all inbound ssh/http traffic and block all outbound traffic?

  Read the article

• Sonicwall Global VPN Client fails to connect, despite successful connections from other computers from behind the same router

  - by JesperE

  I've recently been unable to connect to our Sonicwall VPN at work. The Sonicwall client is stuck on "connecting", and the log says "The peer is not responding to phase1 ISAKMP requests". The weird thing is that this is not an issue with my own PC, only my work laptop (Lenovo W530 running Windows 7 64-bit), and this has only appeared recently. This ought to rule out any problems with my ISP blocking VPN, or issues with the router itself. My company's IT department says that they cannot see anything in their logs when I'm trying to connect. My conclusion is that something is wrong on the laptop itself. Disabling the firewall does not help. Can the VPN connection be blocked in other ways? What should I be looking for? EDIT: This problem has "magically" disappeared, without any changes done in my network. I can only assume that this was caused by some network glitch with my ISP.

  Read the article

• Why are some UDP packets getting blocked?

  - by Tom

  In our organization, we have two test machines running Windows XP. While attempting to test a roll-my-own UDP message server, I found that both could receive small messages (under 2k) just fine. However, when I test sending large packets to both of these machines, one receives them fine, while the other can't receive them at all. Both machines have SP3 and both have their Windows Firewall shut off, but one still isn't working. Can anyone tell me where to look for anything that might be blocking or limiting the packet size on a Windows Machine? Thanks.

  Read the article

• What's the best way to block IP spoofing on a layer 3 switch?

  - by toupeira

  We're hosting Dedicated Servers and are currently using old 3com switches with IP-based ACLs. So each port has an ACL that allows all IP addresses assigned to this customer, and blocks everything else. But now 3com was bought by HP, and the follow-up model only supports basic ACL that aren't flexible enough to both allow certain IPs while blocking others. Looking at other switches in a similar price-range, we've found that most of them have similar problems or don't offer any ACL features at all. I assume this could also somehow be done with VLANs, but if I understand this correctly we'd still need some kind of ACL to actually specify the valid IP addresses for each port. What do you use to make sure your customers don't use unassigned IP addresses? Or what switches can you recommend that have flexible ACL functionality?

  Read the article

• Remote access to a KVM Ubuntu virtual server

  - by Lee

  I've just setup an ubuntu virtual server and everything seems to be working fine. I used KVM to get it working with a bridged network. I've given the virtual server a static ip address on my network. I don't seem to be able to connect to the virtual machine though from outside my network. If I'm on my own network it all works fine, I can ping the ip and connect to it. The virtual server can ping other machines and sites on the internet. I changed the port forwarding rules on my router to forward any connections on a specific port to the virtual server ip address thinking that was the problem, but it was still the same. Is there something I'm missing here which is blocking outside connections to the virtual machine? Thanks.

  Read the article

• Virtualhosts - best way of dealing with it?

  - by axqe56

  I'm competent at the basics of Apache, PHP and virtual hosting but have a question about virtual hosting. As far as I'm aware, HOSTS files can only be in one of the following locations: C:/Windows/system32/drivers/etc (varies in older installs, I believe) I don't think it can be put elsewhere for use with Apache, simply for virtual hosts, and the main HOSTS file for blocking sites etc. I heard about PAC files on Uniform Server's website (http://wiki.uniformserver.com/index.php/Virtual_Hosting:_PAC) but they're browser-specific though, aren't they? What's the best way to deal with virtualhosts, other than HOSTS file? My server isn't currently open to the internet yet, but if it is, what's the best way to resolve DNS for my virtualhost domains if it were to become forward-facing (i.e open to the internet)?

  Read the article

• Can only connect to sql server express 2012 via named pipes

  - by YetAnotherDeveloper

  I have sql server express 2012 installed on windows 2008, locally everything works just fine i can connect via tcpip and named pipes. Remotely i can connect with ssms only using named pipes. I have tried disabling the firewall on both sides to eliminate blocking traffic. i have toggled the tcpip setting on and off (i read somewhere that they got it working just but flipping them off and back on). I have double/triple checked all the settings that i'm aware of and everything seems to be correct. Tcp is enabled Tcp port is set to 1433, udp port is set to 1434 Server has static ip Start up log says: Server is listening on [ 'any' 1433]. Firewall rules are in place Any suggestions on things that i can look into? i have really just run out of ideas.

  Read the article

• Unable to get to remote samba share

  - by tubaguy50035

  I have a remote VPS that I would like to setup samba on and only allow my IP access to it. I currently have in my smb.conf: [global] netbios name = apollo security = user encrypt passwords = true socket options = TCP_NODELAY printing = bsd log level = 3 log file = /var/log/samba/log/%m debug timestamp = yes max log size = 100 [hosting] path = /hosting/ comment = Hosting Folder browseable = yes read only = yes guest account = yes valid users = nick I have the ports (137,138,139,445) open in iptables (they're open to everyone right now while I debug) and I see nothing in the syslog about iptables blocking my requests. When I try to open a file browser to my address \\ipaddress, it hangs for a good thirty seconds, and then opens a log in box. I enter my user name and password for the server, hit okay. It then opens the same box, I enter my credentials again and hit enter. Windows then tells me it could not connect. My user account is added to Samba already. Anybody have any suggestions what I can do to get this working?

  Read the article

• Setting up Multiple Routers (as Hardware Firewalls) behind a Home Router

  - by Synetech

  I’ve currently got one computer behind a router with built-in firewall functionality, connected to a home cable-modem that has a single Ethernet port and one IP. I’m going to have to set up another computer for the rest of the family to use which of course will need to be connected to the Internet, probably wirelessly since the modem is in my room and the new system would not be. What I would like to do is to get two more small routers with firewall capability and connect each computer to a router, which would in turn connect to the main router which connects to the cable-modem. That way, both systems have a hardware firewall protecting them (particularly the wireless system) and the burden of blocking would be reduced on both the computer CPUs and the main router because the secondary routers would handle some of the workload. I’m trying to find out about the complexities inherent in this design and how I could set it up to work, specifically the IP handling and NAT aspect. Thanks a lot.

  Read the article

• Moving Windows 7 ProgramData folder after installation

  - by thinkzig

  I need to move my C:\ProgramData folder in a Windows 7 installation to D:\ProgramData. I understand how to make the symlinks and registry changes so this works. My problem is that I'm unable to copy the files in the ProgramData folder because the OS seems to have some of them locked. Specifically, the files in the C:\ProgramData\Microsoft\Crypto\RSA\MachineKeys folder are blocking the move. Am I out of luck here? Is there any way to move the folder, create the symlink, and update the registry without any of the files in these folders being locked?

  Read the article

• Web server suddenly stopped working

  - by wezten

  I have a web server, which was working fine. It also was an FTP server and a Windows Remote Desktop server, all working fine. Someone called our ISP to increase the internet speed, and suddenly nothing works - I can connect with Teamviewer, but HTTP, FTP & RD doesn't work. Disabled firewall. Ran Wireshark - the packets don't come through at all. Set the webserver to port 20111, in case the ISP is blocking port 80, and again, the packets didn't come through at all. (localhost:20111 works fine) Port forwarding is set up for ports 80, 21, 3389 & 20111 to 10.0.0.32 (which is the correct address - checked with ipconfig). Restarted router and computer. I would be very grateful for any help.

  Read the article

• Tracing what program is making a network connnection? (CentOS)

  - by Airjoe

  I was wondering if it is possible to find out which process is trying to make a specific network connection. On a server I support which hosts websites for about 200 users, the iptables firewall keeps blocking, as it should, a connection to 212.117.169.139 on port 80. Firefox reports this as an attack page (and at the least is obvious spam, if not malicious). It seems something on this server is trying to access this site for some reason, and although it's being blocked successfully, the requests seem to be going through every two to sixty seconds and I'd like to be able to find what process or script is doing this so I can handle it appropriately. Besides doing a grep to try and find if this IP is in some file (which probably won't even work because it may be working by hostname or it may be encoded), is there any way to find out some more information? Thanks!

  Read the article

• Google Chrome giving error 138

  - by gsingh2011

  Google Chrome randomly stopped working one day and is giving me this error: Google Chrome is having trouble accessing the network. This may be because your firewall or antivirus software wrongly thinks that Google Chrome is an intruder on your computer and is blocking it from connecting to the Internet. Here are some suggestions: Add Google Chrome as a permitted programme in your firewall or antivirus software's settings. If it is already a permitted programme, try deleting it from the list of permitted programmes and adding it again. Error 138 (net::ERR_NETWORK_ACCESS_DENIED): Unable to access the network. I didn't make any changes to my firewall settings between the time it was working and when it wasn't working. I'm using the default Windows Firewall. I added Chrome to the allowed programs and restarted, but that didn't fix the error. I even reinstalled Chrome completely and that didn't work either. Any help would be appreciated. EDIT: I forgot to mention that Firefox and IE9 work fine.

  Read the article

• Windows Xp, Svchost.exe connecting to different ips with remote port 445

  - by Coll911

  Im using Windows Xp professional Sp2 Whenever i start my windows, svchost.exe starts connecting to all the possible ips on lan like from 192.168.1.2 to 192.168.1.200 The local port ranges from 1000-1099 and the remote port being 445. After its done with the local ips, it starts connecting to other random ips. I tried blocking connections to the port 445 using the local security polices but it didn't work Is there any possible way i could prevent svchost from connecting to these ips without involving any firewall installed ? since my pc slows down due to the load I'd be thankful for any advices

  Read the article

• What ports do I allow over my internal firewall interface?

  - by blsub6

  I have a Cisco ASA that I have VPN tunnels to connect my internal Windows network. I ran into some trouble logging into my domain so I unblocked all the ports on that internal interface. On a previous question posted here, the general consensus was that I should be blocking ports on my inside interface but my question is: what ports should I unblock? I've tried unblocking ports 88, 139, 135, 389, and 445 and Windows logins still give me problems. Is there some MS documentation somewhere that tells me what I need to unblock to allow Windows logins and other things?

  Read the article

• Can't get nmap to work under Windows 7 64 bit

  - by jitbit

  I'm trying to install and run the nmap tool to test my server, but it keeps saying Note: Host seems down. If it is really up, but blocking our ping probes, try -P0 and showing all the server ports are closed. Which is not true - the server is up and has lots of open ports. Any ideas? UPDATE: Just to clarify - the server can be pinged and port-scanned fine by other programs. It's juts nmap that does not work. Even "google.com" seems to be down for nmap.

  Read the article

• Connecting to iSCSI Target

  - by Joost Verdaasdonk

  I've installed Microsoft iSCSI Software Target 3.3 on a server 2008 R2 machine and created a new iSCSI Target. In the target I created a new Virtual Disk. From another server I started iSCSI Initiator and in Targets | Target I typed the IP of the Target. (Also tried DNS name.) But when I click Refresh I never see the target. Through googling I found this Youtube tut from a French guy doing pretty much what I did (only difference is I'm in a domain). I first though that maybe Port 3260 was closed but its not I can telnet to it. Also disabled all firewalls to see if that was blocking anything... No luck so far. Does anybody know of possible reasons why I can't connect to the iSCSI Target? If I can provide more info please let me know what's needed? Extra info: I've used this tut to set things up.

  Read the article

• Hooking domain to home server with port

  - by user1071461

  Alright, I'm asking two things here. First of all, if i purchase a domain let's say myhomeserver.com, am I able to make the default port go through a different port instead of the default port 80? (that is without having to do myhomeserver.com:5000 for example). Also this should be without blocking other ports (so no stealth forwarding to myhomeserver.com:5000 i think) Secondly, How could I go about hooking a domain to a windows 2008 server? I've seen it on linux but no clue how to do it on windows if it's even possible. I know I'm asking a lot here, just some tips are appereciated. Also, yes I know, using a home server is horrible for security and preformance and whatnot, I understand this already, thanks ^^

  Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >