Search Results

Search found 5655 results on 227 pages for 'cd smith'.

Page 33/227 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

  • Cannot boot from K/Ubuntu install disk on my UEFI system

    - by user93241
    I just got a new system and have been trying to get it set up w/ Win7 & Kubuntu dual-boot, but I've got a major problem. The BIOS of my motherboard (an Asus Crosshair 990FX) is strictly UEFI -- there is no legacy support mode available. I've been reading up on how to get Kubuntu installed in UEFI mode but no matter what I try I cannot seem to even boot into my install CD/USB key properly. I can get as far as the selection screen ("Try Kubuntu", "Install Kubuntu"...) but this screen starts off not appearing correctly. If I try moving the cursor around it sometimes seems to correct itself and show me my choices. But once I select "Try Kubuntu" it starts loading, the screen goes black and then proceeds to flicker -- about once every 5-10 seconds or so. This continues indefinitely. I've tried this with both Kubuntu & Ubuntu installation media, even the AMD64+Mac Ubuntu variety that is supposed to be a lot more flexible w.r.t. UEFI. The only hint I've had that the system might have booted correctly is a little drum sound that plays when booting from the Ubuntu install disk. Well, that and the fact that when I hit my system's power button it seems to shut down correctly, even ejecting the CD at the end. This might be a video driver issue; my system has two nVidia 550's, one of which is attached to my primary monitor. (The secondary isn't hooked up yet.) I'll keep looking over similar questions but any advice would be greatly appreciated. UPDATE: I've tried booting into my 12.04 install CD twice now, each time using two different options supplied by my BIOS. One seemed to offer the ability to boot into my CD under UEFI mode -- this didn't even produce the initial boot menu. The other method offers the ability to boot into my CD NOT under UEFI mode. This DOES produce the boot menu, but after this point it seems I still cannot get to a proper video mode to see what's going on.

    Read the article

  • stuck in busybox after update

    - by Lyra500
    I should start out by saying that I am not very tech savvy and have done my best to understand what is going on here from reading other people's posts and have fumbled my way through several attempted fixes without getting anywhere... I run ubuntu 12.04 on an admittedly cheap laptop from ebuyer and in spite of being cheap and not a brand laptop I have never had any major problems with it. Since updating to 12.04 when it was released the boot-up process has always been slow. Logging in takes about 30secs longer than it used to and if I closed my laptop and opened it again instead of being met with a login screen I'd be met with a black screen with a white mouse. As all of these problems had a behavior-changing fix (don't close laptop, patiently wait for login, etc.) I didn't think of reporting any of the issues. Last night when the update manager prompted me that there were updates available I duly did them as I usually do. At the time a bug report came up and I cannot remember what it said but I reported the bug as I was prompted to do. Then this morning when I started up my laptop it went through the usual sequence, GRUB, purple screen with 'ubuntu' etc. and then when it tried to boot up it went into BusyBox and I have not been able to do anything to solve this. I have tried going into the GRUB menu and starting previous versions but I come to the same point - busybox. I have borrowed another rather elderly laptop with Windows Vista to try and download Boot Repair and Ubuntu and burn them onto CD. I tried downloading boot repair five times, to laptop, CD and USB. Every time it would download and burn fine but then the windows laptop would tell me that 1% did not download properly and my laptop would not run the USB or CD upon booting. I then tried to download ubuntu and make a livecd, twice, but again was told that 1% did not download properly and again my laptop will not run ubuntu from the CD upon booting even if/when I went into the f2 menu and changed the menu priority (if that's what you call it) for booting up to make sure it was definitely trying the USB/CD first. This is the message I get from busybox: BusyBox v1.18.5 (Ubuntu 1:1.18.5-1ubuntu4) built-in shell (ash) Enter 'help' for a list of built-in commands I have tried 'exit' but it mentions things about 'kernal panic' and 'tried to quit init!' and 'can't find /root/dev/console : no such file'. I know that the problem is probably caused by a problem with a kernal caused by the update last night, but I couldn't honestly tell you exactly what was updated and without being able to boot from a livecd I'm not sure how to go about fixing this. As I said, I am not tech savvy and have done what I can to try and find a solution to the problem but I'm starting to feel like I'm out of options. Does anyone have any ideas?

    Read the article

  • With jQuery and I need help getting individual table row titles attributes from an xml file

    - by bfsarmi
    I'm usig tablesorter jQuery to parse this xml file <?xml version="1.0" encoding="iso-8859-1"?> <CATALOG> <CD> <TITLE>Title 01</TITLE> <ARTIST>Artist 01</ARTIST> <COUNTRY>Country 01</COUNTRY> <PRICE>10.00</PRICE> <YEAR>2010</YEAR> <INFO>Tooltip Info 01</INFO> </CD> <CD> <TITLE>Title 02</TITLE> <ARTIST>Artist 02</ARTIST> <COUNTRY>Country 02</COUNTRY> <PRICE>9.00</PRICE> <YEAR>2009</YEAR> <INFO>Tooltip Info 02</INFO> </CD> <CD> <TITLE>Title 03</TITLE> <ARTIST>Artist 03</ARTIST> <COUNTRY>Country 03/COUNTRY> <PRICE>8.00</PRICE> <YEAR>2008</YEAR> <INFO>Tooltip Info 03</INFO> </CD> </CATALOG> and with this code <script type="text/javascript"> $(document).ready(function(){ $.ajax({ type: "GET", url: "file.xml", dataType: "xml", success: function(xml){ $(xml).find("CD").each(function(){ $("#tablebody").append('<tr><td>' + $(this).find("TITLE").text() + '</td><td>'+ $(this).find("ARTIST").text() + '</td><td>'+ $(this).find("COUNTRY").text() + '</td><td>'+ $(this).find("PRICE").text() + '</td><td>'+ $(this).find("YEAR").text() + '</td></tr>'); }); } }); }); </script> I'm new at javascript and have been trying with no luck for a couple of hrs to get the text from the INFO/INFO tags in the xml file to show as title attributes for each table row. The reason for that is that I need to have individual popup tooltips on mouse-over each table row. Many Thanks in advance for any kind of help or suggestions!

    Read the article

  • mod_rewrite settings causes server to throw HTTP 500 errors instead of 404

    - by FractalizeR
    Hello. I have a server with VBulletin forum (working under Apache 2.2, CentOS). The default settings for it in .htaccess are as follows: RewriteEngine on RewriteCond %{HTTP_HOST} ^gsmforum\.ru RewriteRule (.*) http://www.gsmforum.ru/$1 [R=301,L] # If you are having problems or are using VirtualDocumentRoot, uncomment this line and set it to your vBulletin directory. RewriteBase / RewriteCond %{REQUEST_FILENAME} -s [OR] RewriteCond %{REQUEST_FILENAME} -l [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^.*$ - [NC,L] # Forum RewriteRule ^threads/.* showthread.php [QSA] RewriteRule ^forums/.* forumdisplay.php [QSA] RewriteRule ^members/.* member.php [QSA] RewriteRule ^blogs/.* blog.php [QSA] ReWriteRule ^entries/.* entry.php [QSA] RewriteCond %{REQUEST_FILENAME} -s [OR] RewriteCond %{REQUEST_FILENAME} -l [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^.*$ - [NC,L] # MVC RewriteRule ^(?:(.*?)(?:/|$))(.*|$)$ $1.php?r=$2 [QSA] If I try to access any non-existent URL on forum like www.example.com/ajdsjaskasajs, server throws HTTP 500 error. Apache log says: [Sun Apr 25 17:24:32 2010] [error] [client 82.211.152.12] Request exceeded the limit of 10 internal redirects due to probable configuration error. Use 'LimitInternalRecursion' to increase the limit if necessary. Use 'LogLevel debug' to get a backtrace., referer: http://www.gsmforum.ru/forumdisplay.php?424-%CD%EE%E2%EE%F1%F2%E8-%EF%F0%EE%E3%F0%E0%EC%EC%E0%F2%EE%F0%EE%E2 If I switch LogLevel to Debug I get something like this: [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php.php.php.php.php.php.php.php.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php.php.php.php.php.php.php.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php.php.php.php.php.php.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php.php.php.php.php.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php.php.php.php.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php.php.php.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php.php.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt.php [Sun Apr 25 17:30:46 2010] [debug] core.c(3059): [client 95.25.70.85] redirected from r->uri = /robots.txt [root@server2 logs]# tail httpd_error.log [Sun Apr 25 17:31:27 2010] [debug] core.c(3059): [client 217.118.79.27] redirected from r->uri = /clientscript.php.php.php.php.php.php.php, referer: http://74.125.77.132/search?q=cache:bGPJ8XkSvlMJ:www.gsmforum.ru/showthread.php%3Ft%3D62479+%D0%A3%D0%BC%D0%B5%D0%BD%D1%8C%D1%88%D0%B5%D0%BD%D0%B8%D0%B5+%D0%BF%D0%B8%D0%BD%D0%B3%D0%B0+3G+%D0%BC%D0%BE%D0%B4%D0%B5%D0%BC&cd=3&hl=ru&ct=clnk&gl=ru [Sun Apr 25 17:31:27 2010] [debug] core.c(3059): [client 217.118.79.27] redirected from r->uri = /clientscript.php.php.php.php.php.php, referer: http://74.125.77.132/search?q=cache:bGPJ8XkSvlMJ:www.gsmforum.ru/showthread.php%3Ft%3D62479+%D0%A3%D0%BC%D0%B5%D0%BD%D1%8C%D1%88%D0%B5%D0%BD%D0%B8%D0%B5+%D0%BF%D0%B8%D0%BD%D0%B3%D0%B0+3G+%D0%BC%D0%BE%D0%B4%D0%B5%D0%BC&cd=3&hl=ru&ct=clnk&gl=ru [Sun Apr 25 17:31:27 2010] [debug] core.c(3059): [client 217.118.79.27] redirected from r->uri = /clientscript.php.php.php.php.php, referer: http://74.125.77.132/search?q=cache:bGPJ8XkSvlMJ:www.gsmforum.ru/showthread.php%3Ft%3D62479+%D0%A3%D0%BC%D0%B5%D0%BD%D1%8C%D1%88%D0%B5%D0%BD%D0%B8%D0%B5+%D0%BF%D0%B8%D0%BD%D0%B3%D0%B0+3G+%D0%BC%D0%BE%D0%B4%D0%B5%D0%BC&cd=3&hl=ru&ct=clnk&gl=ru [Sun Apr 25 17:31:27 2010] [debug] core.c(3059): [client 217.118.79.27] redirected from r->uri = /clientscript.php.php.php.php, referer: http://74.125.77.132/search?q=cache:bGPJ8XkSvlMJ:www.gsmforum.ru/showthread.php%3Ft%3D62479+%D0%A3%D0%BC%D0%B5%D0%BD%D1%8C%D1%88%D0%B5%D0%BD%D0%B8%D0%B5+%D0%BF%D0%B8%D0%BD%D0%B3%D0%B0+3G+%D0%BC%D0%BE%D0%B4%D0%B5%D0%BC&cd=3&hl=ru&ct=clnk&gl=ru [Sun Apr 25 17:31:27 2010] [debug] core.c(3059): [client 217.118.79.27] redirected from r->uri = /clientscript.php.php.php, referer: http://74.125.77.132/search?q=cache:bGPJ8XkSvlMJ:www.gsmforum.ru/showthread.php%3Ft%3D62479+%D0%A3%D0%BC%D0%B5%D0%BD%D1%8C%D1%88%D0%B5%D0%BD%D0%B8%D0%B5+%D0%BF%D0%B8%D0%BD%D0%B3%D0%B0+3G+%D0%BC%D0%BE%D0%B4%D0%B5%D0%BC&cd=3&hl=ru&ct=clnk&gl=ru [Sun Apr 25 17:31:27 2010] [debug] core.c(3059): [client 217.118.79.27] redirected from r->uri = /clientscript.php.php, referer: http://74.125.77.132/search?q=cache:bGPJ8XkSvlMJ:www.gsmforum.ru/showthread.php%3Ft%3D62479+%D0%A3%D0%BC%D0%B5%D0%BD%D1%8C%D1%88%D0%B5%D0%BD%D0%B8%D0%B5+%D0%BF%D0%B8%D0%BD%D0%B3%D0%B0+3G+%D0%BC%D0%BE%D0%B4%D0%B5%D0%BC&cd=3&hl=ru&ct=clnk&gl=ru [Sun Apr 25 17:31:27 2010] [debug] core.c(3059): [client 217.118.79.27] redirected from r->uri = /clientscript.php, referer: http://74.125.77.132/search?q=cache:bGPJ8XkSvlMJ:www.gsmforum.ru/showthread.php%3Ft%3D62479+%D0%A3%D0%BC%D0%B5%D0%BD%D1%8C%D1%88%D0%B5%D0%BD%D0%B8%D0%B5+%D0%BF%D0%B8%D0%BD%D0%B3%D0%B0+3G+%D0%BC%D0%BE%D0%B4%D0%B5%D0%BC&cd=3&hl=ru&ct=clnk&gl=ru [Sun Apr 25 17:31:27 2010] [debug] core.c(3059): [client 217.118.79.27] redirected from r->uri = /clientscript/vbulletin_css/style-d95b06dc-00001.css, referer: http://74.125.77.132/search?q=cache:bGPJ8XkSvlMJ:www.gsmforum.ru/showthread.php%3Ft%3D62479+%D0%A3%D0%BC%D0%B5%D0%BD%D1%8C%D1%88%D0%B5%D0%BD%D0%B8%D0%B5+%D0%BF%D0%B8%D0%BD%D0%B3%D0%B0+3G+%D0%BC%D0%BE%D0%B4%D0%B5%D0%BC&cd=3&hl=ru&ct=clnk&gl=ru If I remove or comment the last (#MVC) line from .htaccess all is fine. Can you advise me what is the problem with mod_rewrite settings? Why does the last line cause infinite recursion?

    Read the article

  • Cannot Start Nginx Compiled from Source

    - by Jason Alan Kennedy
    I am trying to compile Nginx from source based on the original compiled Nginx server running on my DigitalOcean server ( Ubuntu-14.04 64x ) but with a few extra modules. I can get everything installed smoothly but I can not get it to start. I am sure the ini is correct because I copied the original source off the current running Nginx server [ Even though I see that Nginx now adds the ini when compiling fron source ]. Below is the [ lengthy process ] that I am performing - add sorry but I wanted to be thorough for those who are in need of the info ]. Because I am a newB to Nginx, I am sure I am missing something or just have it all wrong. If you may look over what I have done and see if you spot anything I need/need to change, I will greatly appreciate it. Thnx! With the original Nginx server still running: I check the current/running Nginx configuration so I can build the new Nginx instance the same but with the added modules: nginx -V # The out-put: configure arguments: --with-cc-opt='-g -O2 -fstack-protector --param=ssp-buffer-size=4 -Wformat -Werror=format-security -D_FORTIFY_SOURCE=2' --with-ld-opt='-Wl,-Bsymbolic-functions -Wl,-z,relro' --prefix=/usr/share/nginx --conf-path=/etc/nginx/nginx.conf --http-log-path=/var/log/nginx/access.log --error-log-path=/var/log/nginx/error.log --lock-path=/var/lock/nginx.lock --pid-path=/run/nginx.pid --http-client-body-temp-path=/var/lib/nginx/body --http-fastcgi-temp-path=/var/lib/nginx/fastcgi --http-proxy-temp-path=/var/lib/nginx/proxy --http-scgi-temp-path=/var/lib/nginx/scgi --http-uwsgi-temp-path=/var/lib/nginx/uwsgi --with-debug --with-pcre-jit --with-ipv6 --with-http_ssl_module --with-http_stub_status_module --with-http_realip_module --with-http_addition_module --with-http_dav_module --with-http_geoip_module --with-http_gzip_static_module --with-http_image_filter_module --with-http_spdy_module --with-http_sub_module --with-http_xslt_module NOTE: The configure arguments below return errors during 'make' so I removed them. I don't know what they are - could this be related to my issue??? --with-cc-opt='-g -O2 -fstack-protector --param=ssp-buffer-size=4 -Wformat -Werror=format-security -D_FORTIFY_SOURCE=2' --with-ld-opt='-Wl,-Bsymbolic-functions -Wl,-z,relro' Moving on: # So I don't have to sudo every line: sudo bash # Check for updates first thing: apt-get update # Install various prerequisites needed to compile Nginx: apt-get install build-essential libgd2-xpm-dev lsb-base zlib1g-dev libpcre3 libpcre3-dev libbz2-dev libxslt1-dev libxml2 libssl-dev libgeoip-dev tar unzip openssl # Create System users [ if it doesn't exist - but I see its there on DigitalOceans' Droplets all-ready ]: adduser --system --no-create-home --disabled-login --disabled-password --group www-data # Download NGINX wget http://nginx.org/download/nginx-1.7.4.tar.gz tar -xvzf nginx-1.7.4.tar.gz # Then Google PageSpeed: wget https://github.com/pagespeed/ngx_pagespeed/archive/release-1.8.31.4-beta.zip unzip release-1.8.31.4-beta.zip # cd into the PageSpeed Directory cd ngx_pagespeed-release-1.8.31.4-beta/ # and add the PSOL files in there: wget https://dl.google.com/dl/page-speed/psol/1.8.31.4.tar.gz tar -xzvf 1.8.31.4.tar.gz # Get back to the root directory: cd # I add the ngx_cache_purge module and will install the Nginx Helper plugin for WP later: wget https://github.com/FRiCKLE/ngx_cache_purge/archive/2.1.zip unzip 2.1.zip # Add the headers-more-nginx-module: wget https://github.com/openresty/headers-more-nginx-module/archive/v0.25.zip unzip v0.25.zip # and the naxsi module for added security: wget https://github.com/nbs-system/naxsi/archive/0.53-2.tar.gz tar -xvzf 0.53-2.tar.gz # cd to the new Nginx directory cd nginx-1.7.4 # Set up the configuration build based on the current running Nginx config args and add my additional modules: ./configure \ --add-module=$HOME/naxsi-0.53-2/naxsi_src \ --prefix=/usr/share/nginx \ --conf-path=/etc/nginx/nginx.conf \ --http-log-path=/var/log/nginx/access.log \ --error-log-path=/var/log/nginx/error.log \ --lock-path=/var/lock/nginx.lock \ --pid-path=/run/nginx.pid \ --http-client-body-temp-path=/var/lib/nginx/body \ --http-fastcgi-temp-path=/var/lib/nginx/fastcgi \ --http-proxy-temp-path=/var/lib/nginx/proxy \ --http-scgi-temp-path=/var/lib/nginx/scgi \ --http-uwsgi-temp-path=/var/lib/nginx/uwsgi \ --user=www-data \ --group=www-data \ --with-debug \ --with-pcre-jit \ --with-ipv6 \ --with-http_ssl_module \ --with-http_stub_status_module \ --with-http_realip_module \ --with-http_addition_module \ --with-http_dav_module \ --with-http_geoip_module \ --with-http_gzip_static_module \ --with-http_image_filter_module \ --with-http_spdy_module \ --with-http_sub_module \ --with-http_xslt_module \ --with-mail \ --with-mail_ssl_module \ --add-module=$HOME/ngx_pagespeed-release-1.8.31.4-beta \ --add-module=$HOME/ngx_cache_purge-2.1 \ --add-module=$HOME/headers-more-nginx-module-0.25 [ENTER] Configuration Summary: Configuration summary + using system PCRE library + using system OpenSSL library + md5: using OpenSSL library + sha1: using OpenSSL library + using system zlib library nginx path prefix: "/usr/share/nginx" nginx binary file: "/usr/share/nginx/sbin/nginx" nginx configuration prefix: "/etc/nginx" nginx configuration file: "/etc/nginx/nginx.conf" nginx pid file: "/run/nginx.pid" nginx error log file: "/var/log/nginx/error.log" nginx http access log file: "/var/log/nginx/access.log" nginx http client request body temporary files: "/var/lib/nginx/body" nginx http proxy temporary files: "/var/lib/nginx/proxy" nginx http fastcgi temporary files: "/var/lib/nginx/fastcgi" nginx http uwsgi temporary files: "/var/lib/nginx/uwsgi" nginx http scgi temporary files: "/var/lib/nginx/scgi" Next step: I cd to root and I check the old Nginx folder locations and double checked the 'make' output to see that they are the same: whereis nginx #Output: nginx: /usr/sbin/nginx /etc/nginx /usr/share/nginx NOTE: Not sure about the '/usr/sbin/nginx' - Possible issue??? Next I copy the old /etc/nginx/nginx.conf, /etc/nginx/sites-available/default, /etc/nginx/sites-enabled/default, /etc/init.d/nginx to a text file locally for safe keeping to use in the new Nginx server. Then stop the running Nginx server: service nginx stop , verify it's stopped: service --status-all and the output is: [ - ] nginx To verify that there are two Nginx directories, I cd to: cd nginx* and the output is an error indicating there are two nginx folders - Cool Beans! :) Now Install the new Nginx server: cd nginx-1.7.4 make install # INSTALL OUTPUT ######################################## make -f objs/Makefile install make[1]: Entering directory `/home/walkingfish/nginx-1.7.4' test -d '/usr/share/nginx' || mkdir -p '/usr/share/nginx' test -d '/usr/share/nginx/sbin' || mkdir -p '/usr/share/nginx/sbin' test ! -f '/usr/share/nginx/sbin/nginx' || mv '/usr/share/nginx/sbin/nginx' '/usr/share/nginx/sbin/nginx.old' cp objs/nginx '/usr/share/nginx/sbin/nginx' test -d '/etc/nginx' || mkdir -p '/etc/nginx' cp conf/koi-win '/etc/nginx' cp conf/koi-utf '/etc/nginx' cp conf/win-utf '/etc/nginx' test -f '/etc/nginx/mime.types' || cp conf/mime.types '/etc/nginx' cp conf/mime.types '/etc/nginx/mime.types.default' test -f '/etc/nginx/fastcgi_params' || cp conf/fastcgi_params '/etc/nginx' cp conf/fastcgi_params '/etc/nginx/fastcgi_params.default' test -f '/etc/nginx/fastcgi.conf' || cp conf/fastcgi.conf '/etc/nginx' cp conf/fastcgi.conf '/etc/nginx/fastcgi.conf.default' test -f '/etc/nginx/uwsgi_params' || cp conf/uwsgi_params '/etc/nginx' cp conf/uwsgi_params '/etc/nginx/uwsgi_params.default' test -f '/etc/nginx/scgi_params' || cp conf/scgi_params '/etc/nginx' cp conf/scgi_params '/etc/nginx/scgi_params.default' test -f '/etc/nginx/nginx.conf' || cp conf/nginx.conf '/etc/nginx/nginx.conf' cp conf/nginx.conf '/etc/nginx/nginx.conf.default' test -d '/run' || mkdir -p '/run' test -d '/var/log/nginx' || mkdir -p '/var/log/nginx' test -d '/usr/share/nginx/html' || cp -R html '/usr/share/nginx' test -d '/var/log/nginx' || mkdir -p '/var/log/nginx' ######################################################### I copy/create the files that I saved earlier to txt files in sites-available, the config, default and ini files then symlink them to sites-enabled, and so on. And now to start the server: service nginx start And this is where s#!+ hits the fan - Nada. I check to see if Nginx is running with service --status-all and its not. Also with nginx -V and its not installed??? I reboot the system too and still nothing. So I am not sure what is wrong here. The ini was copied over from the old server along with all the other config files after deleting the old files. When I opened the new compiled files, the nginx default data was present so I replaced them with my old original data prior to starting the new server for the first time. Also to be safe, I rm /etc/nginx/sites-enabled/default and symlinked with ln -s /etc/nginx/sites-available/default /etc/nginx/sites-enabled/default with no errors and I verified that the data was in the sites-enabled/default file. I don't think the server really/fully installed because of the nginx -V result: The program 'nginx' can be found in the following packages: * nginx-core * nginx-extras * nginx-full * nginx-light * nginx-naxsi Try: apt-get install <selected package> Do/should I apt-get install nginx-1.7.4 ?? Or what package do I use being that its a custom package and make install earlier did nothing?? If you need to see the conf files I copied over from the old to the custom server, LMK and I'll post them. Again your help here would be appreciated!

    Read the article

  • Permissions issue Mac OS X Client -> Mac OS X Server

    - by Meltemi
    I can't get access to a folder on our server and can't understand why. Perhaps someone will see what I'm overlooking... Trouble accessing /Library/Subdirectory/NextDirectory/ User joe can ssh to the server just fine and cd to /Library/Subdirectory/ however trying to cd into the next folder, NextDirectory, gives this error: -bash: cd: NextDirectory/: Permission denied both username joe & bill are members of the group admin and both can get INTO Subdirectory without any trouble... hostname:Library joe$ ls -l | grep Subdirectory drwxrwxr-x 3 bill admin 102 Jun 1 14:51 Subdirectory and from w/in the Subversion folder hostname:Subdirectory joe$ ls -l drwxrwx--- 5 root admin 170 Jun 1 22:19 NextDirectory bill can cd into NextDirectory but joe cannot!?! What am I overlooking? What tools do we have to troubleshoot this? thanks!

    Read the article

  • git problems installing stuff [closed]

    - by dale
    root@Frenzen:~# cd root@Frenzen:~# git clone --depth 1 git://source.ffmpeg.org/ffmpeg Initialized empty Git repository in /root/ffmpeg/.git/ root@Frenzen:~# cd root@Frenzen:~# git clone --depth 1 git://source.ffmpeg.org/ffmpeg Initialized empty Git repository in /root/ffmpeg/.git/ root@Frenzen:~# git clone git://source.ffmpeg.org/ffmpeg.git ffmpeg Initialized empty Git repository in /root/ffmpeg/.git/ cd root@Frenzen:~# wget "http://git.videolan.org/?p=ffmpeg.git;a=snapshot;h=HEAD;sf=tgz" -O ffmpeg-snapshot.tar.gz --2012-10-05 05:43:55-- http://git.videolan.org/?p=ffmpeg.git;a=snapshot;h=HEAD;sf=tgz Resolving git.videolan.org... 2a01:e0d:1:3:58bf:fa76:0:1, 88.191.250.118 Connecting to git.videolan.org|2a01:e0d:1:3:58bf:fa76:0:1|:80... root@Frenzen:~# cd root@Frenzen:~# wget "http://git.videolan.org/?p=ffmpeg.git;a=snapshot;h=HEAD;sf=tgz" -O ffmpeg-snapshot.tar.gz --2012-10-05 05:44:17-- http://git.videolan.org/?p=ffmpeg.git;a=snapshot;h=HEAD;sf=tgz Resolving git.videolan.org... 2a01:e0d:1:3:58bf:fa76:0:1, 88.191.250.118 Connecting to git.videolan.org|2a01:e0d:1:3:58bf:fa76:0:1|:80...

    Read the article

  • Delete until previous punctuation mark in Bash

    - by hekevintran
    In Bash, Ctrl + W will erase the last word. Bash considers words to be delimited by spaces. This means that if the cursor is at the end of the string "cd /dir1/dir2/dir3" and you hit Ctrl + W you will be left with "cd ". Is there a Bash shortcut (custom defined is okay) that will leave me with "cd /dir1/dir2/"?

    Read the article

  • Why can't I navigate Active Directory within Powershell?

    - by Myrddin Emrys
    I have an AD: drive, which should allow me to browse active directory from within Powershell. But when I try to use it, it will not let me navigate beyond the root. From what I have read the given commands should work, but they are failing. PS AD:\> ls Name ObjectClass DistinguishedName ---- ----------- ----------------- company domainDNS DC=company,DC=com Configuration configuration CN=Configuration,DC=company,DC=com Schema dMD CN=Schema,CN=Configuration,DC=company,DC=com ForestDnsZones domainDNS DC=ForestDnsZones,DC=company,DC=com DomainDnsZones domainDNS DC=DomainDnsZones,DC=company,DC=com PS AD:\> cd schema Set-Location : Cannot find path 'AD:\schema' because it does not exist. At line:1 char:3 + cd <<<< schema + CategoryInfo : ObjectNotFound: (AD:\schema:String) [Set-Location], ItemNotFoundException + FullyQualifiedErrorId : PathNotFound,Microsoft.PowerShell.Commands.SetLocationCommand PS AD:\> cd Schema Set-Location : Cannot find path 'AD:\Schema' because it does not exist. (duplicate of previous error) PS AD:\> cd company Set-Location : Cannot find path 'AD:\company' because it does not exist. (duplicate of previous error) PS AD:\> ls Schema Get-ChildItem : Cannot find path '//RootDSE/Schema' because it does not exist. (duplicate of previous error) PS AD:\> cd ForestDnsZones Set-Location : Cannot find path 'AD:\ForestDnsZones' because it does not exist. (duplicate of previous error)

    Read the article

  • Remove duplicates from a sorted ArrayList while keeping some elements from the duplicates

    - by js82
    Okay at first I thought this would be pretty straightforward. But I can't think of an efficient way to solve this. I figured a brute force way to solve this but that's not very elegant. I have an ArrayList. Contacts is a VO class that has multiple members - name, regions, id. There are duplicates in ArrayList because different regions appear multiple times. The list is sorted by ID. Here is an example: Entry 0 - Name: John Smith; Region: N; ID: 1 Entry 1 - Name: John Smith; Region: MW; ID: 1 Entry 2 - Name: John Smith; Region: S; ID: 1 Entry 3 - Name: Jane Doe; Region: NULL; ID: 2 Entry 4 - Name: Jack Black; Region: N; ID: 3 Entry 6 - Name: Jack Black; Region: MW; ID: 3 Entry 7 - Name: Joe Don; Region: NE; ID: 4 I want to transform the list to below by combining duplicate regions together for the same ID. Therefore, the final list should have only 4 distinct elements with the regions combined. So the output should look like this:- Entry 0 - Name: John Smith; Region: N,MW,S; ID: 1 Entry 1 - Name: Jane Doe; Region: NULL; ID: 2 Entry 2 - Name: Jack Black; Region: N,MW; ID: 3 Entry 3 - Name: Joe Don; Region: NE; ID: 4 What are your thoughts on the optimal way to solve this? I am not looking for actual code but ideas or tips to go about the best way to get it done. Thanks for your time!!!

    Read the article

  • Variable number of two-dimensional arrays into one big array

    - by qlb
    I have a variable number of two-dimensional arrays. The first dimension is variable, the second dimension is constant. i.e.: Object[][] array0 = { {"tim", "sanchez", 34, 175.5, "bla", "blub", "[email protected]"}, {"alice", "smith", 42, 160.0, "la", "bub", "[email protected]"}, ... }; Object[][] array1 = { {"john", "sdfs", 34, 15.5, "a", "bl", "[email protected]"}, {"joe", "smith", 42, 16.0, "a", "bub", "[email protected]"}, ... }; ... Object[][] arrayi = ... I'm generating these arrays with a for-loop: for (int i = 0; i < filter.length; i++) { MyClass c = new MyClass(filter[i]); //data = c.getData(); } Where "filter" is another array which is filled with information that tells "MyClass" how to fill the arrays. "getData()" gives back one of the i number of arrays. Now I just need to have everything in one big two dimensional array. i.e.: Object[][] arrayComplete = { {"tim", "sanchez", 34, 175.5, "bla", "blub", "[email protected]"}, {"alice", "smith", 42, 160.0, "la", "bub", "[email protected]"}, ... {"john", "sdfs", 34, 15.5, "a", "bl", "[email protected]"}, {"joe", "smith", 42, 16.0, "a", "bub", "[email protected]"}, ... ... }; In the end, I need a 2D array to feed my Swing TableModel. Any idea on how to accomplish this? It's blowing my mind right now.

    Read the article

  • How to do an automated installation of Ubuntu on 100 Remote machines?

    - by user40876
    Help!  I desperately need some advice / help... I want an automated install (via CD or USB) of Ubuntu 10.04 ...on 100 remote machines located all over the country, using a Kickstart configuration file accessible from my web server. How do I create the boot CD (or USB)? How do I specifically add the boot parameters to that boot CD (or USB) to tell it the URL to use for it's automated Kickstart install?

    Read the article

  • Error message during installation of Windows XP Professional

    - by user270686
    During installation of Windows XP Professional the installer had an error which points to a bad CD, so I got another one and tried it, but the same thing happened. What can I do? It says: One of the components Windows needs to continue could not be installed.. The component is called: sys.dll D:/i386/asms/1000/msft/windows/gdiplus/gdiplus.man. I tried running chkdsk /f to fix the errors on the disk. I've searched the internet all day, and I don't know what else to do. I get this error message: SYS.DLL Syntax error in manifest or policy file D:/i386/asms/1000/msft/windows/gdiplus/gdiplus.man on line 4 Error Installation failed d:/I386/asms Error message Data Error (cyclic redundancy check) Fatal error One of the components Windows needs to continue could not be installed. If you are using a CD there might be a problem with the CD try cleaning it and trying again or using another CD.

    Read the article

  • Can't change to Korean-named directory on my debian server

    - by DaLynX
    I made a rsync backup of some directories from a macbook laptop to a debian server. Some of these have korean characters (Hangeul) in their names. After fixing my server's locale, it displays well when I do a ls for instance. But I can't cd to it. Example: $ ls -1 | head ??? dirA dirB … But if try to go browse that directory: $ cd ? ? ? cd: 3: can't cd to ??? Any idea what's wrong and how to fix it ?

    Read the article

  • Installing Ubuntu to a USB drive

    - by Carl Smotricz
    I'm having a rough time getting Ubuntu to run from a 250 GB USB hard drive. I booted Ubuntu 9.10 from a CD and ran the regular "install" to the attached USB drive. I used the "advanced" option on the drive partition question to put the boot loader on /dev/sdb (the USB disk) but when I boot the machine it doesn't recognize there's a boot loader on the USB drive (it offers to boot from 2 other devices but not the USB disk). I also tried booting from the Ubuntu CD and using usb-creator-gtk to set up the USB drive. Seems to me this is meant to work with flash drives. I got a bootable USB disk but it looked and worked like the CD, i.e. it gave me options of "live CD" operation, installing, memtest, etc. That's not the way I want to run the system. Some help in installing Ubuntu, bootable into a "full" running system on my USB drive would be appreciated.

    Read the article

  • PC only boots from Linux-based media and won't boot from DOS-based media

    - by xolstice
    I have this problem where the PC only seems to boot from a floppy disk or CD if it was created as a Linux-based bootable media. If it was created as a DOS-based bootable media the system just freezes at the starting point of the boot process. I originally asked this under question 139515 for CD booting only, and based on the given answers, I was under the impression the problem was with the CD-ROM drive; however, I have since installed a newly purchased CD-ROM drive and the same freezing occurs. This then made me try the DOS bootable floppy disk approach and I was quite surprised that it exhibited the same freezing problem. I then tried try a Linux bootable floppy and everything booted from it without any issues. As I mentioned in my original question, the PC was booting just fine from the DOS-based bootable CD, and then it suddenly decides to pull this freezing stunt. I can't remember if I changed anything in the BIOS settings that may I have caused the problem, but I am wondering if that could be the case - it is currently using the Award Module BIOS v4.60PGMA. Can anyone help?

    Read the article

  • Launching an application from Bash

    - by JBoy
    I'm right now busy with moving the first steps into Linux, i'm using a bash shell within a mac osx I see in all tutorials that in order to launch an application from the bash its necessary to cd to its directory and simply type the name of the app. This is exatly what i'm doing and it does not work (i have on my desktop a 'Eclipse' folder with the launcher icon in it): cd Desktop cd Eclipse Eclipse.app Why will this not work? I read everywhere that typing the name of the app its enough

    Read the article

  • ubuntu not detecting CDdrives

    - by Mirage
    Ihave insatlled ubuntu 10.4 on my compuer with 6 cd drives. Now initiallyi had window server 2008 and i had to install marvel raid sata controller and then my window detected all 6 drives. Now ubuntu is detecting only 3 drives and i have not found marvell drivers for ubuntu bt i have drives for window 2008. Now my question is if i have vrtual machine inside ubuntu using vmware workstation and i install that driver. then can VM dtect thse 6 drives or host has to detect those drives first to make VMs use that Ubuntu shows this thing from terminal *-cdrom:0 description: DVD-RAM writer product: DVDRAM GSA-H10N vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/dvdrw2 logical name: /dev/scd0 logical name: /dev/sr0 version: JL10 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD writer product: DVDRRW GWA-4164B vendor: HL-DT-ST physical id: 0.1.0 bus info: scsi@0:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: 1.01 serial: [HL-DT-STDVDRRW GWA-4164B1.0105/05/12 capabilities: removable audio cd-r cd-rw dvd dvd-r configuration: ansiversion=5 status=nodisc Is t detecting all drives or thise local names just same

    Read the article

  • Going to directory using bash variables doesn't work when directory names have spaces

    - by gsingh2011
    Let's say I want to store the following command in a variable cd "/cygdrive/c/Program Files/" So I do this dir="cd \"/cygdrive/c/Program Files/\"" That should store the command to navigate to the Program Files directory, so when I type $dir it takes me to that directory. To check that the quotations have been properly escaped, I type echo $dir which gives me cd "/cygdrive/c/Program Files/" So everything should be working fine. However, when I type, $dir I get bash: cd: "/cygdrive/c/Program: No such file or directory What am I doing wrong? I'm using Cygwin, but I assume this problem applies to bash in general.

    Read the article

  • How do I import large sql file to local LAMP (xampp) environment

    - by mraslton
    I have used Linux to import a large mysql dump file (into a new database), but am new to how the process works in a local LAMP environment using xampp, as xampp does not support SSH. I've dowloaded the large_dump_file.sql from the Linux server to my local system. I'm using Windows XP and have used xampp to setup LAMP. I am able to access the local_database via phpMyAdmin, but the dump file is too large to import using that app. I'm trying to import the file via the command prompt, but so far with no success. At the prompt: cd .. cd .. cd xampp cd mysql cd bin I've found that mysqlimport is used to import .csv and .txt files, and mysql is used to import .sql files, but can't find documentation as to whether or not to use the -u -p options so I've tried many variations of the command with no luck. What would be the proper command? I've modified the hosts, virtual-hosts conf, and apache config files. Do I need to change any other config files on my local system? Thanks.

    Read the article

  • Incorrect directory permissions with OpenSSH on Cygwin on Windows Server 2008 SP2

    - by Davy Brion
    I ran into a weird directory permission problem when logged in to a Win2008SP2 (not R2) server through SSH. When I open a local cygwin shell on the server, i can do this: myUser@myServer ~ $ cd /cygdrive/c/Windows/System32/inetsrv/ myUser@myServer /cygdrive/c/Windows/System32/inetsrv $ cd config myUser@myServer /cygdrive/c/Windows/System32/inetsrv/config $ I have no issues accessing the 'config' directory when using a local cygwin shell. 'myUser' has all necessary permissions to access the directory as well. In fact, 'myUser' is a local administrator on the machine. Listing the permissions of the config folder through the local cygwin shell shows the following output: 4 drwx------+ 1 SYSTEM SYSTEM 0 Aug 2 09:38 config But when I log into the server with a SSH client (in this case Putty), i run into the following problem: myUser@myServer ~ $ cd /cygdrive/c/Windows/System32/inetsrv/ myUser@myServer /cygdrive/c/Windows/System32/inetsrv $ cd config -bash: cd: config: Permission denied It also doesn't list the proper permissions through SSH: 0 drwxr-x--- 1 ???????? ???????? 0 Aug 2 09:38 config When I look at the running processes on the server with Task Manager (with a remote desktop connection), it shows that all bash.exe processes are running under the 'myUser' account, so I don't understand why I can't access that particular directory through SSH but have no problems accessing it in a local cygwin shell. I'm using OpenSSH 5.9p1-1. I'm not sure what the Cygwin version is... I used the latest setup.exe (version 2.738) of Cygwin, but I can't seem the find any other Cygwin-related version number. I doubt that it's related to SSH/Cygwin though, because when I connect from the Win2008SP2 server to my local Win7 machine through SSH (using the same OpenSSH/Cygwin versions) I can access the /cygdrive/c/Windows/System32/inetsrv/config folder without issues. Does anyone have an idea on what the issue could be?

    Read the article

  • CDROM does not appear on desktop, MACOS 10.5.7

    - by Cheeso
    When I pop a CDROM into the drive of my Macbook Pro, It spins up, I hear it, but no icon appears on the desktop. (I think it's 10.5.7; actually not sure how to verify this on Mac, but I think I saw a 10.5.7 flash by somewhere). In the finder preferences, I have "Show these items on the Desktop" set to show HDs, External Disks, and CDs, DVDs, and ipods. All three of those are checked. I do see the internal HD on the desktop. In Disk utility I can see the CD/DVD hardware. It says "MATSHITA DVD-R UJ-857E...". From Disk Utility I can eject the drive. But in Finder, there is never a CD/DVD listed under "Devices". When I insert a disk, nothing happens, I cannot see it. I also cannot boot from bootable CDROMs by holding C down . Suggestions? I am not very experienced with Mac; I have used Windows for years. EDIT Two updates: I saw this article on support.apple.com, and modified the hostconfig appropriately. It did not have the AUTODISKMOUNT entry, so I added one, rebooted. Same behavior. It does not see the CDROM in Finder, does not mount it on desktop. I put an old manufactured CDROM into the drive, and voila! it showed up on the desktop. The CD that does not appear is a GNome Partition Editor Live CD, which I guess is based on debian. That CD boots in other (non-Mac) PCs. I want to use this to adjust the Bootcamp partition. Suggestions?

    Read the article

  • Formatting the parent and child nodes of a Treeview that is populated by a XML file

    - by Marina
    Hello Everyone, I'm very new to xml so I hope I'm not asking any silly question here. I'm currently working on populating a treeview from an XML file that is not hierarchically structured. In the xml file that I was given the child and parent nodes are defined within the attributes of the item element. How would I be able to utilize the attributes in order for the treeview to populate in the right hierarchical order. (Example Mary Jane should be a child node of Peter Smith). At present all names are under one another. root <item parent_id="0" id="1"><content><name>Peter Smith</name></content></item> <item parent_id="1" id="2"><content><name>Mary Jane</name></content></item> <item parent_id="1" id="7"><content><name>Lucy Lu</name></content></item> <item parent_id="2" id="3"><content><name>Informatics Team</name></content></item> <item parent_id="3" id="4"><content><name>Sandy Chu</name></content></item> <item parent_id="4" id="5"><content><name>John Smith</name></content></item> <item parent_id="5" id="6"><content><name>Jane Smith</name></content></item> /root Thank you for all of your help, Marina

    Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >