Search Results

Search found 4935 results on 198 pages for 'jim white'.

Page 33/198 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

• IPSEC site-to-site Openswan to Cisco ASA

  - by Jim

  I recieved a list of commands that were run on the right side of the VPN tunnel which is where the Cisco ASA resides. On my side, I have a linux based firewall running debian with openswan installed. I am having an issue with getting to Phase 2 of the VPN negotiation. Here is the Cisco Information I was sent: {my_public_ip} = left side of connection tunnel-group {my_public_ip} type ipsec-l2l tunnel-group {my_public_ip} ipsec-attributes pre-shared-key fakefake crypto map vpn1 1 match add customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside static (outside,inside) 10.2.1.200 {my_public_ip} netmask 255.255.255.255 crypto ipsec transform-set aes-256-sha esp-aes-256 esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map vpn1 1 match address customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 Myside ipsec.conf config setup klipsdebug=none plutodebug=none protostack=netkey #nat_traversal=yes conn cisco #name of VPN connection type=tunnel authby=secret #left side (myside) left={myPublicIP} leftsubnet=172.16.250.0/24 #net subnet on left sdie to assign to right side leftnexthop=%defaultroute #right security gateway (ASA side) right={CiscoASA_publicIP} #cisco ASA rightsubnet=10.2.1.0/24 rightnexthop=%defaultroute #crypo stuff keyexchange=ike ikelifetime=86400s auth=esp pfs=no compress=no auto=start ipsec.secrets file {CiscoASA_publicIP} {myPublicIP}: PSK "fakefake" When I start ipsec from the left side/my side I don't recieve any errors, however when I run the ipsec auto --status command: 000 "cisco": 172.16.250.0/24==={left_public_ip}<{left_public_ip}>[+S=C]---{left_public_ip_gateway}...{left_public_ip_gateway}--{right_public_ip}<{right_public_ip}>[+S=C]===10.2.1.0/24; prospective erouted; eroute owner: #0 000 "cisco": myip=unset; hisip=unset; 000 "cisco": ike_life: 86400s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 0 000 "cisco": policy: PSK+ENCRYPT+TUNNEL+UP+IKEv2ALLOW+SAREFTRACK+lKOD+rKOD; prio: 24,24; interface: eth0; 000 "cisco": newest ISAKMP SA: #0; newest IPsec SA: #0; 000 000 #2: "cisco":500 STATE_MAIN_I1 (sent MI1, expecting MR1); EVENT_RETRANSMIT in 10s; nodpd; idle; import:admin initiate 000 #2: pending Phase 2 for "cisco" replacing #0 Now I'm new to setting up an site-to-site IPSEC tunnel so the status informatino I am unsure what it means. All I know is it sits at this "pending Phase 2" and I can't ping the other side, Another question I have is, if I do a route -n, should I see anything relating to this connection? Also, I read a few artilcle where configs contained the interface="ipsec0=eth0", is this an interface that I have to create on the linux debian firewall on my side? Appreciate your time to look at this.

  Read the article

• Windows Live Family Safety Service keeps closing Start Menu

  - by Jim McKeeth

  Got my kids a new Toshiba Laptop for Christmas. I was setting it all up for them so it would be ready to go. Tonight I installed Windows Live Family Safety Parental Controls. In the process of testing I discovered that on all the accounts the Start Menu closes automatically within 3 seconds (or less) of opening. It seems that it happens every 3 seconds, so sometimes it is immediate, and if I open it again then it will stay open for a full 3 seconds. This of course is rather annoying, and I need to wrap it up so it is ready to go under the tree. I disabled the Windows Live Family Safety Service, and that fixed it. Enable it again and the behavior returns. Is this a feature of the service? Can I disable that feature and keep the other features?

  Read the article

• Strange requests coming from Korean Site

  - by Jim Jeffers

  Lately I've been finding a lot of strange requests like this coming to my rails app: Processing ApplicationController#index (for 189.30.242.61 at 2009-12-14 07:38:24) [GET] Parameters: {"_SERVER"=>{"DOCUMENT_ROOT"=>"http://www.usher.co.kr/bbs/id1.txt???"}} ActionController::RoutingError (No route matches "/browse/brand/nike ///" with {:method=>:get}): It looks like it's automated as I get a lot of them and notice the strange parameters they're trying to send: _SERVER"=>{"DOCUMENT_ROOT"=>"http://www.usher.co.kr/bbs/id1.txt??? Is this something malicious and if so what should I do about it?

  Read the article

• In SharePoint, why can I "multiple document upload" a 47,297 byte file, but not a 47,298 byte file?

  - by Jim

  It's strange. I can upload a document named 47k.txt that is 47,297 bytes using the "Multiple Document Upload" feature. However, if I add a single character to the end of the text file, the upload fails. Also, if I rename the file to 47k*x*.txt and try to upload it, it fails. This is the error I get in the SharePoint logs: Category: General Event ID: 8jzm Level: High Message: #90012: An error was encountered while processing files on the server. Try uploading one file at a time by using the single upload page. The same error is reported in a message box on the client side. Does anybody know why this would happen?

  Read the article

• Windows update stuck. Fixt it stuck. So is KB947821. What should I do?

  - by Jim Thio

  I installed a new computer. After I installed I update everything and let the computer runs for days. Then I don't know what my daughter do. The computer stop responding. Windows update no longer work. People said to run fix it. Fix it run and after that the problem still persist and it still doesn't work. The problem changes though. Before there is some error code. Now windows update simply "updating" never end. So I downloaded KB947821. It's been 3 hour and it's still installing. Looks like it hit firewall or something. i don't see windows update on firewall exception list. However, I've never heard that this is an issue. Firewall only protect against incoming transaction, not outgoing right? Or what am I missing. What should I do?

  Read the article

• How to mix textures in DirectX?

  - by tobsen

  I am new to DirectX development and I am wondering if I am taking the wrong route to achieve the following: I would like to mix three textures which contain transparent areas and some solid areas (Red, Blue, Green). The three textures should blend like shown in this example: How can I achieve that in DirectX (preferably in directx9)? A link or example code would be nice. Update: My rendering method looks like this and I still think I am doing it wrong, because the sprite only shows the last texture (nothing is rendered transparent or blended): void D3DTester::render() { d3ddevice->Clear(0, NULL, D3DCLEAR_TARGET, D3DCOLOR_XRGB(0,0,0), 1.0f, 0); d3ddevice->BeginScene(); d3ddevice->SetRenderState(D3DRS_ALPHABLENDENABLE, TRUE); d3ddevice->SetRenderState(D3DRS_SRCBLEND, D3DBLEND_ONE); d3ddevice->SetRenderState(D3DRS_DESTBLEND, D3DBLEND_ONE); LPD3DXSPRITE sprite=NULL; HRESULT hres = D3DXCreateSprite(d3ddevice, &sprite); if(hres != S_OK) { throw std::exception(); } sprite->Begin(D3DXSPRITE_ALPHABLEND); std::vector<LPDIRECT3DTEXTURE9>::iterator it; for ( it=textures.begin() ; it < textures.end(); it++ ) { sprite->Draw(*it, NULL, NULL, NULL, 0xFFFFFFFF); } sprite->End(); d3ddevice->EndScene(); d3ddevice->Present(NULL, NULL, NULL, NULL); } The resulting image looks like this: But I need it to look like this instead: Update2: I figured out that I have to SetRenderState after I use sprite->Begin(D3DXSPRITE_ALPHABLEND); thanks to the hint by Josh Petrie. However, by using this: sprite->Begin(D3DXSPRITE_ALPHABLEND); d3ddevice->SetRenderState(D3DRS_ALPHABLENDENABLE, TRUE); d3ddevice->SetRenderState(D3DRS_SRCBLEND, D3DBLEND_ONE); d3ddevice->SetRenderState(D3DRS_DESTBLEND, D3DBLEND_ONE); std::vector<LPDIRECT3DTEXTURE9>::iterator it; for ( it=textures.begin() ; it < textures.end(); it++ ) { sprite->Draw(*it, NULL, NULL, NULL, 0xFFFFFFFF); } sprite->End(); The sprites colors are becoming transparent towards the background scene e.g.: if I use d3ddevice->Clear(0, NULL, D3DCLEAR_TARGET, D3DCOLOR_XRGB(0,100,21), 1.0f, 0); the result looks like: Is there any way to avoid that? I would like the sprites be transparent to each other but to be still solid to the background. Update3: After having sombody explained to me, how to do what @LaurentCouvidou and @JoshPetrie suggested, I have a working solution and therfore accept the answer: d3ddevice->BeginScene(); D3DCOLOR white = D3DCOLOR_RGBA((UINT)255, (UINT)255, (UINT)255, 255); D3DCOLOR black = D3DCOLOR_RGBA((UINT)0, (UINT)0, (UINT)0, 255); sprite->Begin(D3DXSPRITE_ALPHABLEND); sprite->Draw(pTextureRed, NULL, NULL, NULL, black); sprite->Draw(pTextureGreen, NULL, NULL, NULL, black); sprite->Draw(pTextureBlue, NULL, NULL, NULL, black); sprite->End(); sprite->Begin(D3DXSPRITE_ALPHABLEND); d3ddevice->SetRenderState(D3DRS_ALPHATESTENABLE, TRUE); d3ddevice->SetRenderState(D3DRS_BLENDOP, D3DBLENDOP_ADD); d3ddevice->SetRenderState(D3DRS_SRCBLEND, D3DBLEND_ONE); d3ddevice->SetRenderState(D3DRS_DESTBLEND, D3DBLEND_ONE); sprite->Draw(pTextureRed, NULL, NULL, NULL, white); sprite->Draw(pTextureGreen, NULL, NULL, NULL, white); sprite->Draw(pTextureBlue, NULL, NULL, NULL, white); sprite->End(); d3ddevice->EndScene(); d3ddevice->Present(NULL, NULL, NULL, NULL);

  Read the article

• What causes random clicking/navigation sound while PC is idle?

  - by Jim Linny

  On my Dell D630 laptop running Windows XP Pro SP3, I randomly hear the "Windows Navigation Start.wav" played. This happens even if the only application active on the PC at the time is Microsoft Outlook and no one is touching the keyboard or touchpad. The start navigation sound IS enabled for Internet Explorer (I have IE 7 installed), but it is not running (no window open, anyway). The clicks are rapid, as if being executed automatically by a script or process, and they always come in threes: "click-click, click". I don't see any changes on the display and I don't know how to figure out what's running that could cause this. I have tried to leave Windows Task Manager open in the hope that I'll see a process name jump to the top of the list briefly, but it doesn't happen that often and I guess I'm not quick enough. The PC is slower than I think it should be, but System Idle Process is at 96 - 99 during the event, and for most of the time when I'm not actually using the machine. Any ideas?

  Read the article

• Windows 7 playback of dvr-Microsoft files stutters

  - by Jim Lynn

  I've just had to install Windows 7 on my Media Center machine because my Vista installation had a faulty drive. I've got the latest drivers that I can find - Intel 945GM integrated Graphics, Realtek audio drivers. Things are working OK with one exception. Playback of old recordings, from dvr-Microsoft format files, is choppy. The picture freezes for a fraction of a second, then quickly catches up. The sound is uninterrupted and doesn't pause. These freezes happen once every 5 seconds or so. It's very regular. Playback of Live TV from the digital tuner is perfectly smooth. DVD playback is perfectly smooth. As an experiment, I used the MPEG editing package VideoReDo to create a small test file in three different formats. This program takes the raw MPEG streams and repackages them into the desired container. I took the same clip and created three files in three formats: dvr-Microsoft (Microsoft's old recorded TV format); mpg (standard MPEG); and ts (raw MPEG transport stream of the kind often produced by PVRs). When these three files are played back under Windows 7, the mpg and ts files play smoothly, but the dvr-Microsoft file stutters. The last piece of data I have is that two other Windows 7 machines can play back dvr-Microsoft files smoothly with no stuttering. One is a netbook, with less grunt than the media centre. So there must be something specific about my Media Center machine that's causing the problem. Does anyone have any idea where I can look now? I don't know much about AV software, codecs, filter graphs etc. but I suspect that's where the problem lies. Rendering the video isn't the problem, but extracting the streams is. How would I go about diagnosing the problem? Edited to add: I just used the GraphStudio tool to look at the filter graph on the offending PC. The filter graph it uses by default for dvr-Microsoft looks identical to the other machines, and, interestingly, when I play the files using GraphStudio they run smoothly. Under Windows Media Player and Windows Media Center they stutter. I'd like to see the filter graph for Windows Media Player but GraphStudio won't show it. It looks like Windows Media Player and WMC are using a different decoding path to GraphStudio. Edited again to add: Today I purchased a new HDTV. The same Media Center driving the TV at 1080p is now playing back the old Recorded TV files smoothly, without stuttering. So whatever the cause of the original problem, using a different resolution seems to have removed the problem. It might also explain why nobody else has had this problem. I doubt many people use Media Centre with a 14in portable TV.

  Read the article

• Programmer Desk

  - by Jim

  I'm building a home office and looking for the ultimate desk. Lot's of resources about the great desk chairs, but very little on great modern desks. Requirements: $1000-$2000. Straight. No side cabinets. Attractive. Electric adjustable would be nice, but I haven't found very attractive looking one. The one recommended in this thread is pretty ugly http://www.beyondtheofficedoor.com/adjustable-height-table.php The Herman Miller Sense desk looks nice: http://www.csnofficefurniture.com/asp/superbrowse.asp?clid=32&caid=&sku=HML1212&refid=PG7-HML1212 . Big fan of Herman Miller after my Aeron and Mirra. Does anyone have any experience with their desks? EDIT: Thanks all for the advice. I ended up just going with the Galant after seeing it and the Herman Miller's in person. What a great desk!

  Read the article

• Can't move or access WSS Central Administration site

  - by Jim

  We have several WSS Servers: WSS1 WSS2 WSS3 WSS4 SharePoint thinks that Central Administration is on WSS3 and that it can be access via SSL on port 22641. The problem is that central administration is not there. It was removed using the config wizard. We removed central admin from all servers to clean everything out, and we tried installing Central Admin on WSS1. The alternate access mappings still point to central admin on WSS3. We tried deleting the alternate access mappings, but SharePoint won't let you delete central admin's mapping. Later, we removed central admin from all of our servers and tried creating the Central Admin website on WSS3, where SharePoint already thinks it is. But for some reason SharePoint is creating the alternate access mappings using SSL, and we don't have a certificate for the server. Why is SharePoint creating alternate access mappings routing an https internal URL by default? How can we move central administration to a new server? We are using WSS 3.0.

  Read the article

• HDD RAID0 question

  - by Jim

  If you have 2 raptor 10k rpm drives in Raid0, can you add another sata (7200prm) drive outside of the RAID or would it have to be inside the RAID? What would be the consequences of adding a 7200 RPM drive to the raptor 10k rpm RAID0 besides the I/O speed going to 7200rpm.

  Read the article

• Security Essentials not installing and I suspect my machine is infected with malware

  - by Jim

  My mouse seems to be automatically right-clicking every few seconds, and sometimes constantly. My cursor will abruptly become an hourglass for a moment every once in a while, as well. It happens in spurts, as in it hasn't happened for about 10 minutes, but the preceding 20 before that it was happening constantly. I suspect that my machine is infected with malware of some sort, so I've tried installing Microsoft Security Essentials, but it presents the following error upon installation failure: My questions are: How can I solve the MSE installation issue and run a scan? Are there any indications that malware isn't actually my issue? Is MSE my best way to go about solving my issue, assuming that malware actually is the problem? Many thanks!

  Read the article

• Hosting 2 different SSL domains on the same IP [closed]

  - by Jim

  Possible Duplicate: Multiple SSL domains on the same IP address and same port? I have 2 different domains, domain1.com and domain2.net. Both require SSL certificates. I've got the certificates signed by a CA and now need to set them up on Apache. I've got a single IP address and have found a post here: SSL site not using the correct IP in Apache and Ubuntu that apparently works for ubuntu but I am on CentOS and have not had the same luck trying that configuration. When I try that configuration, Apache dies telling me that the port is already in use: (98)Address already in use: make_sock: could not bind to address 0.0.0.0:443 I had SSL working for a single domain but now that I've added the second, I get a browser warning about the cert not belonging to the domain. How do I get both domains to work using virtual host containers?

  Read the article

• How to change controller numbering/enumeration in Solaris 10?

  - by Jim

  After moving a Solaris 10 server to a new machine, the rpool disk is now c1t0d0. We have some third party applications hard coded for c0t0d0. How can I change the controller enumeration on this machine? There is no longer a c0. I've tried rebuilding the /etc/path_to_inst, but the instance numbers don't seem to match up with the controller numbers. Also, it's not clear if i86pc platforms use this file. I've tried devfsadm -C to clear the dangling links, but I'm not sure how to cause devfsadm to start numbering from 0 again (or force certain devices in the tree to a specific controller number). Next I am going to try to create the symlinks manually in /dev/dsk and rdsk to point to the correct /devices. I feel like I am going way off path here. Any suggestions? Thanks

  Read the article

• Mysterious login attempts to windows server

  - by Jim Balo

  I have a Windows 2008R2 server that is reporting failed login attempts from a number of workstations on our network. Some event log details: Event ID 4625, Status: 0xc000006d, Sub Status: 0xc0000064 Security ID: NULL SID, Account Name: joedoe, Account Domain: Acme Workstation Name: WINXP1, Source Network Address: 192.168.1.23, Source Port: 1904 Logon Process: NtLmSsp, Authentication Package: NTLM, Logon Type: 3 (network) I believe this is coming from some netbios service or similar (maybe the file explorer), keeping an inventory of its network neighborhood and also trying to authenticate. Is there a way to turn this off without having to turn off file sharing all together? In other words, clients authenticating against file servers that they use is of course no problem, but I want to eliminate clients trying to authenticate to servers that they are not using and have no business with. The above example is only one of thousands of log alerts for similar failed network authentications. What can I do to clean this up / handle this? Thanks.

  Read the article

• How to Copy CD+Graphics / Karaoke CDs?

  - by Jim McKeeth

  Is there any good software to copy CD+Graphics (aka Karaoke CDs) for Windows 7? Preferably free. I can copy the audio portion just fine, but for some reason I keep looking the karaoke lyrics / graphics portion. It used to be that a lot of the software supported these specifically, but now I am having a hard time finding any mention of this feature, and the ones I have tried didn't work.

  Read the article

• Outlook: How do I configure multiple sources to dump incoming messages to a central Inbox?

  - by Jim G.

  Given: A Gmail account. A Hotmail account. Multiple RSS feeds. How do I configure Outlook to dump all incoming messages into the central Inbox folder?

  Read the article

• What is a good programmer's desk? [closed]

  - by Jim

  I'm building a home office and looking for the ultimate desk. Lot's of resources about the great desk chairs, but very little on great modern desks. Requirements: Straight. No side cabinets. Attractive. Electric adjustable would be nice, but I haven't found very attractive looking one. The one recommended in this thread is pretty ugly. The Herman Miller Sense desk looks nice. Big fan of Herman Miller after my Aeron and Mirra. Does anyone have any experience with their desks? EDIT: Thanks all for the advice. I ended up just going with the Galant after seeing it and the Herman Miller's in person. What a great desk!

  Read the article

• Is Centos legal?

  - by Jim B

  I'm trying to figure out if centos is legal (or simply grey). Here's what makes me wonder: They seem to go to great pains not to mention that they are based on redhat in the FAQ they mention a policy about using the redhat trademark, but the link no longer exists. When installing it it's not hard to find a lot of redhat code. I don't bother much with the linux world anymore but I had a client that was wondering about it as his auditors picked up on it and wanted to know where his license was.

  Read the article

• Why does QuickTime lag in Firefox if I don't put my mouse over it?

  - by Jim McKeeth

  This has happened for me as long as I can remember. Since the first version of Firefox, on multiple computers and under different versions of Windows. QuickTime plays fine in IE and Chrome (even with Firefox in the background), but in Firefox if my mouse is not over the QuickTime window then it will start to studder, then lag and eventually just stop. To be honest, I do keep quite a few tabs open, but Firefox stays at 1% CPU (even when QuickTime runs) and I have a few gigs of free RAM. It is the same for any resolution of video or audio. If the mouse is just one pixel in the client area of the QuickTime then it usually plays fine. Other video formats typically play fine. Does anyone else notice this behavior? Ultimately I would like a fix besides keeping my mouse over the QuickTime window.

  Read the article

• How to change controller numbering/enumeration in Solaris 10?

  - by Jim

  After moving a Solaris 10 server to a new machine, the rpool disk is now c1t0d0. We have some third party applications hard coded for c0t0d0. How can I change the controller enumeration on this machine? There is no longer a c0. I've tried rebuilding the /etc/path_to_inst, but the instance numbers don't seem to match up with the controller numbers. Also, it's not clear if i86pc platforms use this file. I've tried devfsadm -C to clear the dangling links, but I'm not sure how to cause devfsadm to start numbering from 0 again (or force certain devices in the tree to a specific controller number). Next I am going to try to create the symlinks manually in /dev/dsk and rdsk to point to the correct /devices. I feel like I am going way off path here. Any suggestions? Thanks Update: This is on virtual ESXi hardware with an additional pass-through HBA. There is no controller 0 on the machine, that is for sure. devfsadm -C cleans up all the c0 device symlinks but keeps the already linked controllers at their current ids.

  Read the article

• Can I repair a short circuiting problem in a Dell Inspiron 6000 that occurs when it is picked up?

  - by jim.e.clark

  I have a couple of Dell Inspiron 6000 notebooks that work perfectly fine unless you pick them up by one corner (as most people would). When you lift the notebook it flexes slightly and the notebook shorts out. Sometimes even a gentle bump will cause this to happen. So far the notebook always starts back up without issue, but this behavior is...inconvenient. It occurred to me that someone familiar with the innards might be able to suggest a little MacGyver fix for this. A little electrical tape in the right spot or something like that. Or perhaps this is a common problem and the answer is here, waiting for me to stumble on the correct keywords. I would appreciate any suggestions Note: It is probably worth mentioning that I have disassembled a Dell notebook before to replace a bluetooth card so I comfortable opening up the systems.

  Read the article

• Why can't the Adobe Flash player send key strokes it doesn't handle to the browse in which it is run

  - by jim.e.clark

  I'm a heavy web user that uses the address bar constantly while browsing the web. I often use Ctrl + T to open a new tab or Ctrl + D to move focus to the address bar so it is very annoying that these shortcut keys do not work when a Flash object has focus on the active browser tab. I would happily give up all keyboard handling in the Flash Player in exchange for having keystrokes sent to the browser. In fact, as someone who has worked in software development for over 15 years it is hard to believe that Flash doesn't pass common browser shortcut keys to the browser or have an option to do so. So my question is this: Am I missing some option, some Flash shortcut key or some Firefox add-on that will alleviate my suffering?

  Read the article

• Best SQL database gui tool for linux?

  - by jim

  Specifically I'm looking for a native linux program that is similar in functionality to Navicat or SQLYog. I.e. I need something good at editing data. Free would be best, but not essential. Thanks!

  Read the article

• STARTTLS issues with sendmail

  - by Jim

  I just switch hosts and now have to configure sendmail with certificates in order to send mail. Is there anyone here that can point me to some solid documentation that is known to work? I'm on CentOS, using sendmail 8.13. I am currently trying to figure out why I am getting "Relaying denied. Proper authentication required". I'd be happy to post my mc file if someone thinks thay can help..

  Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >