Search Results

Search found 14483 results on 580 pages for 'major mode'.

Page 333/580 | < Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >

• Firewalling a Cisco ASA Split tunnel

  - by dunxd

  I have a Cisco ASA 5510 at head office, and Cisco ASA 5505 in remote offices. The remote offices are connected over a split tunnelled VPN - the ASA 5505s use "Easy VPN" Client type VPN in Network Extension Mode (NEM). I'd like to set firewall rules for the non-tunnelled traffic only. Traffic over the VPN to head office should not have any firewall rules applied. I might want to apply different firewall rules to different remote offices. All the documentation I have been able to find assumes the Client VPN is a software endpoint, and all the configuration is done at the 5510. When using a Cisco 5505 as the VPN client, is it possible to configure any firewalling at the Client end, or does it all have to come from the 5510? Are there any other issues to look out for when split-tunnelling a VPN by this method?

  Read the article

• How to Disable Disk Quota When Checkbox is Grayed Out in Windows XP?

  - by Webs

  I am logged in as Administrator on a computer that is removed from the domain, it is only in a workgroup. I was trying out different settings and turned on disk quota. I set the quota limit pretty low and didn't realize it would have an effect on the Admin acct. Now when I log in a temporary profile gets created and the option to remove the quota is grayed out. I am in Safe Mode right now and can't seem to un do the quota with the admin acct. Did I change another setting somewhere that striped away my rights to remove the quota? Does anyone have any ideas beyond reinstalling?

  Read the article

• How to manage preventive maintenance planning for external IT support?

  - by code-gijoe

  I am a bit puzzled by the way to handle server upgrade planning for software we maintain on remote sites. This is my case: I work for a software company that has many external clients. We are trying to be more Agile in our development so we plan to release small improvements every quarter and we wish to keep our clients informed of maintenance schedules. Instead of having angry clients that believe there ROI of our support plan is low, we want to be more proactive. Lets say we have 100 machines to take care of, is there some tool to assist me in planing the maintenance with clients? Right now I get a call from a client that is unhappy requesting we upgrade them, that is when we go into panic mode and start making calls. That is when I need to check my calendar, coordinate with the other guys, call a few times, change the date again and again until everyone is happy. Can this be done better?

  Read the article

• Isass.exe Application error

  - by shelbang

  I own a hp mini. It has come up with a blue screen and says: The Application failed to intialize properly (0xc0000005). Click on OK to terminate the application. i click on it twice but it stayed on the blank blue screen. i have tryed going on the safe mode thingy.. and pressing F9 and F10 and F8 but none of the above work. Considering its a HP mini- it doesnt have a cd rom compartment!?!? pleasee help !! i cant live without my computer! ): - ps using sisters computer atm :S shhh

  Read the article

• Mac OS x 10.4 Tiger Will Not Boot

  - by keithbrown38

  My G5 Tower all of a sudden is ONLY booting to the Registration page, the where after you installed the software you are suppose to Register. I cant get it to boot in safe mode, so I am using my usb 2.0 SATA cable to connect my drive to a my macbook pro and I am using (CCC) Disc to Disc Clone and it is copying to my external WD passport drive and that makes a startup disc along with all my info from my drive. My question is was there anything easier and less time consuming than that? Does anyone know why this would happen all of a sudden? Thank You All in Advance for your help and support! Keith B

  Read the article

• Copying windows 8 Users folder having long long paths

  - by bilal.haider

  I was trying to move my "Users" folder in Windows 8 as described here and here. But when I try to copy the folder using "xcopy" in Windows Installation Disk Repair Mode, after some files are copied, I get "insufficient memory". The files on which the error is given are like C:\Users\Bilal\Application Data\Application Data\Application Data.........Application Data\Application Data..... What is the point in such directories within directories? I also tried copying them using Mini Windows XP, but the problem was there too.. Also tried copying using Parted Magic Live CD... but still.. So now, how can I move them? Another Question. Is moving such/ system files using Linux a good idea? Does it do anything to permissions?

  Read the article

• Laptop freezes on Wireless Mouse Adapter attach/detach

  - by Sergiy Byelozyorov

  I am using Microsoft Wireless Notebook Optical Mouse 3000 with Toshiba Satellite Pro P300-1CG. Recently I have installed Windows 7 64-bit. Now once in a while when I plug-in or plug-out wireless mouse adapter, the computer freezes (image stays on the screen, but the computer is not responsive). I have noticed that it mostly happens after I recover my computer from sleep mode. To continue using laptop I have to shut it down by pressing and holding power button for 7 seconds and then booting it up again. What can be done to prevent this?

  Read the article

• Windows 7 connect to Lion file sharing

  - by McKvack

  Trying to access my Mac from a Windows 7 computer, I fail with the infamous error 86 incorrect password. Now this appears to be a well-known problem with countless threads on the internet giving as many "solutions" as there are discussion threads about it (mostly ranging from installing third-party commercial samba servers, to switching to some other protocol, to compiling a plain-vanilla Samba installation - the latter which I will probably do when I give up this :) ) I am stubborn, and I believe there must be some problem here that can be solved or worked around, but there is surprisingly little detail about this problem. It appears to have something to do with a mismatch of authentication methods. Trying to run samba in debug mode: sudo /usr/sbin/smbd -debug -stdout gets me this output when trying to access it from Win 7 ... smb1_dispatch_one [smb_dispatch.cpp:377] dispatching SMB_COM_SESSION_SETUP_ANDX smb1_dispatch_session_setup [session_setup.cpp:261] FIXME erase existing sessions log_gss_error [gssapi_mechanism.cpp:97] gssapi: gss-code: Miscellaneous failure (see text) log_gss_error [gssapi_mechanism.cpp:113] gssapi: mech-code: unknown mech-code 22 for mech unknown What is the problem here, and how do I fix it?

  Read the article

• Restoring Mac-bootcamp-windows-partition image to Windows machine

  - by jpwagner

  Hi, I'm running Windows XP sp3 on my mac using bootcamp. Objective: I'd like to move this partition to a windows machine. This is what I tried: 1. create image using winclone 2. restore drive to disk partition on windows machine using paragon 3. reboot from new partition Results: it attempts to boot in XP (windows flag and progress bar load screen) but then gives me the old BSOD. safe mode just hangs while loading. (I then uninstalled KB977165 on a hunch, but that did nothing to help the issue.) Any ideas, advice, etc would be greatly appreciated. Thanks!

  Read the article

• Restoring Mac-bootcamp-windows-partition image to Windows machine

  - by jpwagner

  Hi, I'm running Windows XP sp3 on my mac using bootcamp. Objective: I'd like to move this partition to a windows machine. This is what I tried: 1. create image using winclone 2. restore drive to disk partition on windows machine using paragon 3. reboot from new partition Results: it attempts to boot in XP (windows flag and progress bar load screen) but then gives me the old BSOD. safe mode just hangs while loading. (I then uninstalled KB977165 on a hunch, but that did nothing to help the issue.) Any ideas, advice, etc would be greatly appreciated. Thanks!

  Read the article

• Windows Media Center command line options?

  - by Pridkett

  Is there a command line interface to Windows Media Center in Windows 7. I have an SSH daemon installed on my media center box and would love to be able log in via SSH and get the list of upcoming recordings. As it is, I need to use Remote Desktop and then tell Media Center to run in GDI mode to display the upcoming recordings which is slow and cumbersome. Here are interesting commands that I'm wondering about: List upcoming recordings List most recent recordings Status of scheduler I'd rather not have to install Remote Potato to accomplish this.

  Read the article

• Macvim lags while Vim on terminal is buttery smooth

  - by SaamJB

  I am running OS X Lion 10.7.3 and Macvim runs significantly slower than vim on the terminal for me. All movement commands in Macvim are much slower. Moving up and down in visual mode is equally as laggy. I see none of this lag when using vim from the terminal. Does anyone know what the reasons may be? I am running NERDtree on every open tab, and I know this contributes some memory overhead and potentially some slow down; but even when I don't run NERDtree Macvim runs much slower than vim from the terminal. Any help in solving this would be greatly appreciated.

  Read the article

• How can I port forward with an airport extreme and a NAT enabled modem?

  - by Jon

  I run an Actiontec HD701D modem with NAT to an Airport extreme base station to laptop etc. As you might expect I get double NAT issues. I tried a lot of different things to forward a port, but no luck. Currently the airport is in bridge mode letting the modem handle the NAT, but still can't forward the port. Also to note: firewall is off on the router, firewall is set to allow the application in OSX 10.6.3 and I did forward the port in the router. No luck.

  Read the article

• ubuntu12.04 hangs at checking battery state

  - by crystalbass17

  My 12.04 system hangs at "Checking battery state". At this stage, no commands work eg: ctrl+alt+f1, alt+f5. I ran recovery mode, I ran the command sudo mount -o remount, rw sudo dpkg-reconfigure gdm and gdm was the only one installed so I didn't get a GUI screen. I have an integrated graphics card "Intel Corporation Mobile 4 chipset Integrated Graphics Controller (rev 07)". So I cannot install nvidia drivers as everyone else suggests. I have gone through several similar questions but everyone suggests reconfiguring gdm or reinstalling graphic drivers. I did sudo add-apt-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get upgrade to get the latest x-swat drivers. The system still hung at the same line. The other option is to reinstall ubuntu, which is out of the question, since we have a very specific install for our project where the settings are very hard to duplicate. Suggestions/Comments welcome.

  Read the article

• How to prevent mod_cluster as single point failure?

  - by Hitesh

  In my configuration i used Apche+mod_cluster as a front_end(load balancer) server and two JBOSS AS 7.1.0 as backend server. In my configuration on one system i have install Apache+mod_cluster + JBOSS AS 7.1.0 and on other system JBOSS AS 7.1.0. Both JBOSS AS 7.1.0 are in domain mode means in clustering. My problem is that if Apche+mod_cluster crash than client can not access any JBOSS AS . I want to configure Apache+mod_cluster in Master_Slave format, means if one of Apache+mod_cluter down another Apache+mod_cluster become active and pass client(browser) request to back-end server in normal form without any interruption. Is there any way to make two Apache+mod_cluster to communicate with each other , means to check health status of each other and if any one get down other Apche+mod_cluster will do it's task ......

  Read the article

• Browser-based Operating System

  - by Ross Peoples

  I have a bunch of touchscreen machines that I want to display a webpage on and have users interact with the webpage via the touchscreen. Right now, this is done with a full-blown OS with a browser set to run at startup. I think maybe the ideal solution is to use a Linux-based OS that boots up, starts X, then starts a web browser (Chrome, Firefox, or whatever) in full screen mode. What kind of options do I have? I really want to avoid using a full-blown OS like I do now. It looks unprofessional and takes a while to boot up. I was thinking maybe Chrome OS or something, but I wouldn't know how to set it up for my purposes, since it's still designed to be used as a desktop OS instead of a kiosk-type OS.

  Read the article

• Windows program to remove titlebar, frame, etc from a window?

  - by Nelson

  I like playing computer games in windowed mode, as opposed to full screen. I don't like staring at the title bar, frame, and other UI junk. I also don't like seeing other stuff on my desktop around the window. Is there a simple Windows program that will strip the UI chrome off of an arbitrary window from some other application? Extra points for an easy way to put a black screen underneath the window, hiding the desktop. Note: I'm looking specifically to handle windows that are smaller than my desktop size. There's a variety of 'windowed maximized' options that make a window exactly the desktop size, and positioned so all the UI decorations are off screen. (E.g.: ShiftWindow). I'm trying to strip all the decorations away from a window that's smaller than desktop size.

  Read the article

• Gentoo on Mac Mini - can't get framebuffer to work

  - by user42055

  I have the last Gentoo on an intel mac mini with 945G graphics. I'm trying to start X (with no config) but it complains that /dev/fb0 doesn't exist. I've tried adding the following options to the kernel boot params: video=intelfb:mode=800x600-32@60,accel,hwcursor vga=761 Because I read that the fb might not be enabled unless you set a vga= option. Unfortunately the kernel doesn't recognise that option. If I changed it to vga=ask it presents me a list of about 6 text modes no greater than 80x60. In the kernel I have agpgart, drm (using i830 module) and vga text console compiled in. What am I not doing right ?

  Read the article

• Gentoo on Mac Mini - can't get framebuffer to work

  - by user42055

  I have the latest Gentoo on an intel mac mini with 945G graphics. I'm trying to start X (with no config) but it complains that /dev/fb0 doesn't exist. I've tried adding the following options to the kernel boot params: video=intelfb:mode=800x600-32@60,accel,hwcursor vga=761 Because I read that the fb might not be enabled unless you set a vga= option. Unfortunately the kernel doesn't recognise that option. If I changed it to vga=ask it presents me a list of about 6 text modes no greater than 80x60. In the kernel I have agpgart, drm (using i830 module) and vga text console compiled in. What am I not doing right ?

  Read the article

• Laptop turns off after 20 minutes of use

  - by Christoph

  My laptop a sony vaio VGN-NW11S http://www.trustedreviews.com/Sony-VAIO-VGN-NW11S-S---15-5in-Laptop_Laptop_review. Everytime i turn it on, in safe mode or not, if i try to open an application i.e. run a process such as google chrome or event viewer, defrag, virus scan, it completely turns off without warning, nor giving a trace of events the next time I switch it on. Apart from that, I had worries it might be my battery or power supply but I dont think it is that, I took the laptop apart cleaning fans etc. and have ordered some cpu paste as I checked to see the condition of the processor. I will post to see if re-applying the paste works. One more thing, when the heavy processes kick in, the fan starts to make a lot of noise, maybe trying to cool down the CPU? Any ideas on what else it could be and what I could do to test what is wrong?

  Read the article

• Why won't apache load a symlinked file from conf.d?

  - by kdt

  I have an apache configuration file which works fine when it's placed directly in /etc/httpd/conf.d/foo.conf. However, when I move the same file somewhere else (for example, move it to /tmp/foo.conf) and then create a symlink with ln -s /tmp/foo.conf /etc/httpd/conf.d then apache fails on startup with: httpd: could not open document config file /etc/httpd/conf.d/foo.conf I've tried making the file and the symlink mode 777, and tried changing them to be owned by the apache user. It seems like apache is failing to load the file purely on the basis of it being a symlink, but I'm sure I've used symlinks successfully on other machines. Is there something I'm missing? Does apache have an option for refusing to load config files if they're symlinks? The operating system is CentOS 4.4, apache version 2.0.52.

  Read the article

• Scripted printer configuration changes

  - by David Steven

  I've got about a dozen Windows XP machines that I need to make a couple specific printer configuration changes to. The printer is "virtual" printer for an electronic delivery service. I'd like to not have to visit each machine individually. I already have the means to execute commands remotely on the machines, I just can't seem to find away to adjust these settings via command line or script. Specifically I need to be able to make the following changes: 1) As an admin user: - Device Settings - Font Substitution Table/Courier New - Change to "Courier" 2) As a specific* user: - Printer Preferences - Paper/Quality - Advanced - Change Graphic/Print Quality to "600 x 600" - Change Document Options/Printer Features/Graphics Mode to "HP-GL/2" *This change is a per user configuration, unless there's some way to make it once. In this situation I only really need it for a specific (different) user on each machine.

  Read the article

• Wake computer from sleep/standby without BIOS support for WOL?

  - by jjeaton

  Just bought a new home server and the nice folks at HP disabled the Wake-On-Lan feature in my motherboard. Are there any other options for waking the computer from Sleep/Standby mode? I'd like to take advantage of power savings wherever I can. I realize that I won't be able to wake it from shutdown, short of putting together some Rube Goldberg machine. EDIT: I'd like to be able to wake the machine on demand, remotely. So I can then RDP into it, or access files, etc.

  Read the article

• VMWare Converter recommendations

  - by Tank Szuba

  I have two Ghost 14 backups of my machine. One for the machine fully configured with apps after and XP install and one of the last update before i re-imaged it (it's XP, I re-image about once every six months). I recently wanted to try simply using my initial image in a virtual environment to do my testing that generally causes me to need to re-image. I used the VMWare converter to convert the Ghost images to a virtual machine to use in Virtual box but they fail to properly boot. They get stuck after the bios loads and windows begins loading. If I power down the machine and refire it it will go to the error screen in windows that asks if you would like to boot to a different mode. none selected make any difference. What are some possible errors I should look for in the conversion process or in my settings for the converter?

  Read the article

• How to set the request start time with HAProxy?

  - by Tupy

  I would like to measure the time of full request stack. The New Relic capture time of the middleware (e.g. java, python, ruby) and request time (See https://newrelic.com/docs/features/tracking-front-end-time). For this, I need to configure the X-Request-Start header as the request pass through the HAProxy load balance. The haproxy.cfg should look like: backend www balance roundrobin mode http reqadd "X-Request-Start" UNKNOWN_TIME_FUNCTION() server servername 192.168.0.1:80 weight 1 check There is a haproxy native function to replace the UNKNOWN_TIME_FUNCTION()?

  Read the article

< Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >