Search Results

Search found 14402 results on 577 pages for 'interface builder'.

Page 336/577 | < Previous Page | 332 333 334 335 336 337 338 339 340 341 342 343 | Next Page >

Bridging VirtualBox over OpenVPN TAP adapter on Windows

- by Sean Edwards

I'm trying to configure a virtual machine (VirtualBox guest running Backtrack 4) with a bridged adapter over a VPN connection. The VPN is is hosted by the cybersecurity club at my university, and connects to a sandboxed LAN designed for penetration testing against various servers that the club has built. My host (Windows 7 Ultimate) connects to the VPN fine and is assigned an IP through DHCP, but for some reason the VM can't do the same thing, and I'm not sure why. It's like OpenVPN is filtering out packets from the MAC address it doesn't recognize. I want the virtual machine to bridge over the VPN connection, because our IT office has very strict policies about what you can and can't do on the network. I want to be able to run active attacks (ARP spoofing, nmap, Nessus scans) in the sandbox environment without risking the traffic accidentally going over the university network and getting my internet access revoked. Bridging over the VPN connection and running all attacks from inside the VM would solve that problem. Any idea why the host can use this interface, but the VM can't?

Read the article
RAID1 Hard drives with Intel Controller

- by Dave_H

I have an older server with 2 35GB hard drives arranged as a RAID-1 drive. I have 3 open bays, I'd like to add 2 more hard drives to the open bays and have all 4 drives configured as a RAID-1 drive that Windows sees as 1 larger drive. Is this possible? If not, the new drives are 2x as big as the old drives, is it possible to replace 1 of the old drives and rebuild then replace the second drive and rebuild and somehow expand the array to use all of the available space? The server is using an Intel hardware raid controller, the software interface is Intel Storage Console v2.12.

Read the article
Share laptop Wi-Fi with router set up as access point via ethernet cables

- by obie

I have an ADSL modem which serves as a wireless router. There's a laptop connected to it through cable. On the other room I have a laptop which is connected through the router wirelessly. Since I have other appliances that need to get connected but are not Wi-Fi capable I have another Wi-Fi router. How can I share the second laptop's Wi-Fi with the second router so that the router can then serve as an access point to give internet to my other appliances through ethernet cables? I want something like this: INTERNETMODEM (WIFI)LAPTOP 1 (WIFI)LAPTOP 2 (WIFI)Router 2 (ETHERNET)DREAMBOX & WDTV What I've tried so far is opened the admin interface of router 2 then set static IP 192.168.100.13 and disabled the DHCP. The DHCP of the main router starts with 192.168.100.1 then I hooked up router 2 with the laptop 2 through Cat5 cable but for some reason it's not working.

Read the article
Public IP Routing over Private GRE tunnel

- by Paul

I have a GRE tunnel configured between two linux boxes. The tunnel works fine. I can ping from each host the other private ip. Head privateip: 10.0.0.1 publicip: 8.8.8.8 Tail privateip: 10.0.0.2 publicip: 7.7.7.7 The public IP on Tail has the network block 9.9.9.0/23 statically routed over the 7.7.7.7 interface. The idea is to make the 9.9.9.0/23 ips work on servers on the 8.8.8.8 network. I configure the tail host to route the /23 block. I mounted a 9.9 IP on the head server. I can ping the 9.9 ip from the tail to the head. I can't ping the 9.9 ip from the public internet. I think I need to add some other routes because of gateway issues, but I can't seem to wrap my mind around it (not a router guy, just beating my way through something that I have never done before and vaguely understand) --danks

Read the article
Fastest way to move files from a guest VM to the host?

- by iTayb

Hey there. I'm looking for the fastest way to copy files from a VM to physical servers. Setting up a network between them isn't a thing I'd like to do. I believe it is much more secure when not having one. VMware suggests using the Copy-VMGuestFile cmdlet from their PowerCLI interface, however I find it slow (Running at approximately 1.5MB/s). I thought of the following: Creating a new virtual hard drive, moving the files in, and download the .vmdk file from the server, then extracting it locally. It is possible, however will not work with working VMs, and I don't want to shut-down the VM every time I want to move files. Use the virtual floppy device and download the .flp file. It works even if the VM is running, but it is limited to 2.8MB. Do I have any other way? I'm using ESXi 4.1. Thanks.

Read the article
Software for monitoring internal software?

- by Tyler Eaves

Is there any good software for monitoring the health of a collection of related software? Requirements are as follows: Web-based, deployable on standard Linux/BSD software. Configurable to support a variety of processes, scheduled at various intervals. Some sort of dashboard interface, for monitoring status, viewing errors, etc. As an example, suppose we have a daily export that's scheduled to run at 6AM each morning. After the export completes, it would POST a status message, saying it had completed, passing in some sort of application key to identify the export. If that status message hadn't come in, by, say, 6:30AM, an e-mail might be sent, that application should go red on the dashboard, etc. Applications should also be able to post error/warning messages. Basically the goal is to be able to monitor all of our internal projects from one system, rather than a multitude of e-mails, log files, etc. I suspect that I'll probably have to end up writing this from scratch, but I just thought I'd ask.

Read the article
Is it possible to disable ARP in Windows 7

- by DriverGuy

I have a unique requirement where I need to disable ARP on a Windows 7 box. In previous Windows versions you could modify the ArpRetryCount in the registry (and set it to 0), but this does not work in 7 (nor does it exist). Does anybody know how, or if this is possible? I've been asked to elaborate this more and I'm not quite sure how. I want to switch off ARP (including gratuitous arp) on Windows 7 for a project I'm working on. You can do this in Linux by simply adding '-arp' when you bring up an interface, but you cannot do this in Windows 7. You could in previous versions by modifying the registry, but this does not work any more. If the fine folk here aren't sure then I don't like my chances...

Read the article
Is there a Windows or Linux equivalent of Soulver calculator application?

- by Shevek

I've just been shown a brilliant calculator app called Soulver which is only available on Mac OS X Maths on a Mac as it should be Soulver is a new kind of calculator application which uses a simple yet powerful word-processor style interface instead of the traditional "button" approach to doing math. Main Features No equals button - Soulver instantly calculates as you type. Multiple lines - Soulver lets you do math over multiple lines and edit previous expressions. Flexible to words - Soulver doesn't mind if you include words or labels between numbers. Basic functions - Soulver includes every standard calculator function, like sin(), cos() & tan() Clever English functions - Soulver includes some "English" math functions. For instance you can type "10% off $200" and get $180 Floating palettes - Soulver's answer & stats palettes will give you conversions and statistics on your work as your type Save your work - like a word processor, Soulver allows you to save and reopen your work This is a fantastic concept and I would really like to find it's equivalent for Windows and/or Linux. Any suggestions?

Read the article
Open source alternative for Canonical Landscape?

- by netvope

From Canonical: Landscape is an easy-to-use systems management and monitoring service that enables you to manage multiple Ubuntu machines as easily as one through a simple Web-based interface. However, Landscape is not free. The RedHat counterpart Satellite has a free version called Spacewalk, but it doesn't work on Ubuntu. (There is an attempt to port Spacewalk to Debian, but it doesn't look like it's stable yet.) Are there any open source alternative to Landscape? Better yet, are there any Spacewalk-like software that works for both RedHat-based and Debian-based systems?

Read the article
Cisco 2811 router ignored input errors

- by elbekay

I've got a Cisco 2811 (AdvIPServices 12.4(25e)) that is showing input errors on both its interfaces, all the errors are of the ignored type. The counter for ignore errors is not increasing continuously, which made me think it would be happening in line with traffic bursts, but there really isn't a large amount of traffic running through it at any time. Both the router interfaces are connected to a 4900 (IPBase 12.2(54)) series switch. The only things I can see are: There is a slight mismatch in duplex/speed negotiation settings, one side is set to auto/auto and one full/auto, however they have negotiated fine. There have been a few fallbacks on the interface buffers, and some trims in the public buffers. Any suggestions for things to look at? I will be correcting the duplex neg settings, and might try a buffer tune, but I don't think it will help.

Read the article
How to increase hard drive transfer speed

- by atif089

This is my motherboard GA-M61PME-S2 (SATA upto 3.0 Gbps) and This is my Hard Disk Samsung hd502hi Capacity 500 GB Cache 16MB Disks / Heads 1 / 2 Interface SATA 3Gb/s Spindle Speed 5400 RPM Sustained Data Rate OD 100 MB/s Average Seek 8.9 ms Average Latency 5.56 ms Data Transfer Rate 300 MB/sec Weight 470 grams Power: Idle / Seek / R-W / Spin-up 3.9W / 4.8W / 5.1W / ~24W Acoustics (sound power) 2.2 / 2.7 Bel (idle / quiet seek / performance seek) When I copy things from one partition to another they transfer at a maximum of 30 MBps. However the drive supports upto 300 MBps right ? How do I increase the transfer speeds? P.S - Using Windows XP, All partitions are NTFS.

Read the article
DNS Settings in Cisco Wireless Lan Controllers

- by Braden

The WLC is a 2100 series and I have looked back and forth through the entire web interface. Originally the idea was that the gateway should be the DNS controler and the WLC pointed directly at the gateway. For some reason, random clients are having DNS specific issues when it comes to seeing certain shares around the network. The problems are also very intermittent. Aside from going to each box and implementing a static DNS is there ACTUALLY a DNS setting lodged into the WLC settings (and I am being a numpty and can't find them) or am I stuck with performing the config 1 by 1?

Read the article
Error in using DBAN on HDD

- by John Watson

I am using DBAN to erase HDD. DBAN is loaded from a CD and BIOS Boot order has been set to favour CD drive. On starting laptop, system boots from CD and DBAN interface can be seen. DBAN detects two storage devices, HDD and the SD Card. My HDD IS 320GB but DBAN says 298GB. It erases the SD card but when i try to erase HDD, it gives following error. DBAN finished with non-fatal errors. *ERROR /dev/sdb (process crash) *ERROR /dev/sda (process crash)

Read the article
Can't resolve localhost on Mac OS X Server

- by iainbeeston

I have a server running OS X Server 10.5 and it can't resolve localhost to 127.0.0.1. When I try ping this is what happens: ping localhost ping: cannot resolve localhost: Unknown host SSH and web browsers get similar results (uknown host). If I try using 127.0.0.1 or the ip address assigned on the LAN all of the above work. Here's the contents of my /etc/hosts file: cat /etc/hosts ## # Host Database # # localhost is used to configure the loopback interface # when the system is booting. Do not change this entry. ## 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost I have no local DNS service running. Does anyone have any idea why this might be happening or how I can fix it?

Read the article
Using Zebra LP 2844-Z over the network

- by Jason Kealey

Hello, I am looking for a network-based label printer. I am looking at this Zebra LP-2844-Z printer. Unfortunately, it does not come with a network interface like the lower-end LP 2824 Plus. The ZebraNet 10/100 Print Server is both expensive for what it does (~$600) and only seems to support wireless networking, not wired. I prefer wired for reliability. Questions: Can I use a cheaper off-the-shelf print server to turn the LP-2844Z to a network printer. Would I get any trouble communicating with the printer via its own programming language or via OPOS? (instead of the Windows driver) Are cheaper print servers reliable? Would I be better to get another printer model that has it built in directly to avoid having issues due to the print server? What other printer would you recommend?

Read the article
cisco 6500 crash enabling netflow

- by bleomycin

Hello everyone, i have a cisco 6503 running IOS 12.2(33)sxi5 and i'm trying to enable netflow. Following the instructions here http://www.manageengine.com/products/netflow/help/cisco-netflow/cisco-ios-netflow.html enabling for interface vlan 3, shortly after ip flow-export version 5 console outputs: CPU_MONITOR-6-NOT_HEARD: CPU monitor messages have not been heard for 30 seconds crashlog here: http://pastebin.com/Niv2H8xD it then writes a crash log and reloads the router. Has anyone else experienced anything like this before? Here is my running config prior to adding the options in the above link: http://pastebin.com/AgNb1ahG Thank you for any help!

Read the article
IP route ppp0 + eth0 access to outside network

- by Vitor

I need some help in define a route I have two connections one from eth0 and other a ppp0 (a 3G card) Not having the ppp0 connection active my route table is: Destination Gateway Genmask Flags Metric Ref Use Iface default DD-WRT 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 I can access my webserver from an outside network through ethernet interface Than I have also my ppp0 3G connection active havig the following route table: D estination Gateway Genmask Flags Metric Ref Use Iface default 10.64.64.64 0.0.0.0 UG 0 0 0 ppp0 10.64.64.64 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 Now I only can access my webserver in outside networks through the IP of the 3G connection Note that my server is serving at 0.0.0.0 IP (to all interfaces) But I need to get access to webserver to both interfaces ethernet and 3G connection I only can have access to both connection in local network Any help to configure this network to have both interfaces with outside networks access is welcome Can anyone give me an example to configure this network with 2 gateways to give outside networks access One for IP 192.168.1.149 and other for the ppp0 IP 89.214.60.196 Tanks

Read the article
Handling Junk Email with Apple Mail.app and Gmail

- by Axeva

I've just setup my Apple Mail client to work with Google Apps through IMAP. One lingering question is how to best handle SPAM (Junk Mail), however. In their Help section, Google recommends that we disable junk filtering on the client. http://mail.google.com/support/bin/answer.py?answer=78892 This leads me to wonder what we should do when a junk message makes it past Google's filter? Do I just delete the message? If I do, the Google spam filter will never improve and "learn" that the message was junk. Do I have to log in to the web interface at Google to mark the message as spam? That seems a bit arduous for every spam email I get. What's the best way to handle this? Thanks!

Read the article
Allow Incoming Responses Apache. On Ubuntu 11.10 - Curl

- by Daniel Adarve

I'm trying to get a Curl Response from an outside server, however I noticed I cant neither PING the server in question nor connect to it. I tried disabling the iptables firewall but I had no success. My server is running behind a Cisco Linksys WRTN310N Router with the DD-wrt firmware Installed. In which I already disabled the firewall. Here are my network settings: Ifconfig eth0 Link encap:Ethernet HWaddr 00:26:b9:76:73:6b inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:b9ff:fe76:736b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:49713 errors:0 dropped:0 overruns:0 frame:0 TX packets:30987 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52829022 (52.8 MB) TX bytes:5438223 (5.4 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:341 errors:0 dropped:0 overruns:0 frame:0 TX packets:341 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:27604 (27.6 KB) TX bytes:27604 (27.6 KB) /etc/resolv.conf nameserver 192.168.1.1 /etc/nsswitch.com passwd: compat group: compat shadow: compat hosts: files dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis /etc/host.conf order hosts,bind multi on /etc/hosts 127.0.0.1 localhost 127.0.0.1 callcenter # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.1.120 netmask 255.255.255.0 network 192.168.1.1 broadcast 192.168.1.255 gateway 192.168.1.1 The Url to which im trying to get a connection to is https://www.veripayment.com/integration/index.php When I ping it on terminal heres what I get daniel@callcenter:~$ ping https://www.veripayment.com/integration/index.php ping: unknown host https://www.veripayment.com/integration/index.php daniel@callcenter:~$ ping www.veripayment.com PING www.veripayment.com (69.172.200.5) 56(84) bytes of data. --- www.veripayment.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms PHP Function in codeigniter public function authorizePayment(){ //--------------------------------------------------- // Authorize a payment //--------------------------------------------------- // Get variables from POST array $post_str = "action=payment&business=" .urlencode($this->input->post('business')) ."&vericode=" .urlencode($this->input->post('vericode')) ."&item_name=" .urlencode($this->input->post('item_name')) ."&item_code=" .urlencode($this->input->post('item_code')) ."&quantity=" .urlencode($this->input->post('quantity')) ."&amount=" .urlencode($this->input->post('amount')) ."&cc_type=" .urlencode($this->input->post('cc_type')) ."&cc_number=" .urlencode($this->input->post('cc_number')) ."&cc_expdate=" .urlencode($this->input->post('cc_expdate_year')).urlencode($this->input->post('cc_expdate_month')) ."&cc_security_code=" .urlencode($this->input->post('cc_security_code')) ."&shipment=" .urlencode($this->input->post('shipment')) ."&first_name=" .urlencode($this->input->post('first_name')) ."&last_name=" .urlencode($this->input->post('last_name')) ."&address=" .urlencode($this->input->post('address')) ."&city=" .urlencode($this->input->post('city')) ."&state_or_province=" .urlencode($this->input->post('state_or_province')) ."&zip_or_postal_code=" .urlencode($this->input->post('zip_or_postal_code')) ."&country=" .urlencode($this->input->post('country')) ."&shipping_address=" .urlencode($this->input->post('shipping_address')) ."&shipping_city=" .urlencode($this->input->post('shipping_city')) ."&shipping_state_or_province=" .urlencode($this->input->post('shipping_state_or_province')) ."&shipping_zip_or_postal_code=".urlencode($this->input->post('shipping_zip_or_postal_code')) ."&shipping_country=" .urlencode($this->input->post('shipping_country')) ."&phone=" .urlencode($this->input->post('phone')) ."&email=" .urlencode($this->input->post('email')) ."&ip_address=" .urlencode($this->input->post('ip_address')) ."&website_unique_id=" .urlencode($this->input->post('website_unique_id')); // Send URL string via CURL $backendUrl = "https://www.veripayment.com/integration/index.php"; $this->curl->create($backendUrl); $this->curl->post($post_str); $return = $this->curl->execute(); $result = array(); // Explode array where blanks are found $resparray = explode(' ', $return); if ($resparray) { // save results into an array foreach ($resparray as $resp) { $keyvalue = explode('=', $resp); if(isset($keyvalue[1])){ $result[$keyvalue[0]] = str_replace('"', '', $keyvalue[1]); } } } return $result; } This gets an empty result array. This function however works well in the previous server where the script was hosted before. No modifications where made whatsoever Thanks in Advance

Read the article
How to change the fonts used in Foxit Reader?

- by user982438

I really want to use Foxit Reader as my default PDF reader for its Tab Interface, and low memory footprint. Having tried mutiple times over the years the only thing that is stopping me are the Fonts. PDF in Adobe Reader looks Regular, but PDF Rendered in Foxit Looks Ugly. Would this solution works in Chrome as well? Since i record Chrome is using Foxit Reader as its embedded PDF engine. And is there any reasons why Fonts are used differently in Adobe and Foxit Reader?

Read the article
Alternate Client for Cisco Unified Personal Communicator protocol

- by Jason M

At work we have an in-house chat system using CUPC. Does anyone else out there use this? There are a few things I do not like about this client: Where's the chat log? If I close the window out, I have no way of getting my conversation back. Tabbed interface? That would be nice. I hate having multiple chat windows up, having to arrange them around my desktop as more people start talking to me. I don't like that I have to use this one-off application for this protocol when other chat clients will handle 99% of the other protocols I use. Tell me: Is the protcol an open standard for which other applications have support? (pidgin, adium, digsby, etc.) If not, can I overcome these issues from within CUPC? Perhaps there are newer versions of the client that overcome these issues.

Read the article
Windows 7 client can't connect to CentOS PPTP VPN

- by Chris

Have a Macintosh (10.8.2) that connects just fine to a CentOS 6.0 virtual private server (OpenVZ, with PPP added by the host) via PPTP. A Windows 7 Home Premium client (virtualized in Sun's Virtual Box), on the same computer, using the same Ethernet connection, cannot connect to the Linux VPN server. I have iptables disabled (for testing) on the Linux box. I have the Windows firewall turned off. /var/log/messages looks like this, for a Windows connection: Oct 12 18:44:30 production pptpd[1880]: CTRL: Client 66.104.246.168 control connection started Oct 12 18:44:30 production pptpd[1880]: CTRL: Starting call (launching pppd, opening GRE) Oct 12 18:44:30 production pppd[1881]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Oct 12 18:44:30 production pppd[1881]: pptpd-logwtmp: $Version$ Oct 12 18:44:30 production pppd[1881]: pppd options in effect: Oct 12 18:44:30 production pppd[1881]: debug#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: nologfd#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: dump#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: plugin /usr/lib/pptpd/pptpd-logwtmp.so#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: require-mschap-v2#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: refuse-pap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: refuse-chap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: refuse-mschap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: name pptpd#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: pptpd-original-ip 66.104.246.168#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: 115200#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: lock#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: local#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: novj#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: novjccomp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: ipparam 66.104.246.168#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: proxyarp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: 192.168.97.1:192.168.97.10#011#011# (from command line) Oct 12 18:44:30 production pppd[1881]: nobsdcomp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: require-mppe-128#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: mppe-stateful#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:44:30 production pppd[1881]: pppd 2.4.5 started by root, uid 0 Oct 12 18:44:30 production pppd[1881]: Using interface ppp0 Oct 12 18:44:30 production pppd[1881]: Connect: ppp0 <--> /dev/pts/1 (At this point the Windows machine displays a dialog, reading: "Verifying user name and password...") Oct 12 18:45:00 production pppd[1881]: LCP: timeout sending Config-Requests Oct 12 18:45:00 production pppd[1881]: Connection terminated. Oct 12 18:45:00 production pppd[1881]: Modem hangup Oct 12 18:45:00 production pppd[1881]: Exit. Oct 12 18:45:00 production pptpd[1880]: GRE: read(fd=6,buffer=8059660,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Oct 12 18:45:00 production pptpd[1880]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Oct 12 18:45:00 production pptpd[1880]: CTRL: Client 66.104.246.168 control connection finished The Macintosh connecting looks like this in /var/log/messages: Oct 12 18:50:49 production pptpd[1920]: CTRL: Client 66.104.246.168 control connection started Oct 12 18:50:49 production pptpd[1920]: CTRL: Starting call (launching pppd, opening GRE) Oct 12 18:50:49 production pppd[1921]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Oct 12 18:50:49 production pppd[1921]: pptpd-logwtmp: $Version$ Oct 12 18:50:49 production pppd[1921]: pppd options in effect: Oct 12 18:50:49 production pppd[1921]: debug#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: nologfd#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: dump#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: plugin /usr/lib/pptpd/pptpd-logwtmp.so#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: require-mschap-v2#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: refuse-pap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: refuse-chap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: refuse-mschap#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: name pptpd#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: pptpd-original-ip 66.104.246.168#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: 115200#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: lock#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: local#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: novj#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: novjccomp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: ipparam 66.104.246.168#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: proxyarp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: 192.168.97.1:192.168.97.10#011#011# (from command line) Oct 12 18:50:49 production pppd[1921]: nobsdcomp#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: require-mppe-128#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: mppe-stateful#011#011# (from /etc/ppp/options.pptpd) Oct 12 18:50:49 production pppd[1921]: pppd 2.4.5 started by root, uid 0 Oct 12 18:50:49 production pppd[1921]: Using interface ppp0 Oct 12 18:50:49 production pppd[1921]: Connect: ppp0 <--> /dev/pts/1 Oct 12 18:50:52 production pppd[1921]: MPPE 128-bit stateless compression enabled Oct 12 18:50:52 production pppd[1921]: Unsupported protocol 'IPv6 Control Protocol' (0x8057) received Oct 12 18:50:52 production pppd[1921]: Unsupported protocol 'Apple Client Server Protocol Control' (0x8235) received Oct 12 18:50:52 production pppd[1921]: Cannot determine ethernet address for proxy ARP Oct 12 18:50:52 production pppd[1921]: local IP address 192.168.97.1 Oct 12 18:50:52 production pppd[1921]: remote IP address 192.168.97.10 Oct 12 18:50:52 production pppd[1921]: pptpd-logwtmp.so ip-up ppp0 chris 66.104.246.168 I'm baffled...

Read the article
Snap Server 18000 connection help!

- by sicko666

I wonder if anyone here can help me. I have a home server setup made up of old secondhand computers, 2 servers running Windows Server 2003, 1 workstation running Windows 7, a 16 port switch & an adsl ethernet modem. All these connect and talk to each other fine but then I got a "Snap Server 18000" and a "Snap disk 30sa" sata array. When I turn the Snap on, it boots past the BIOS, runs a kernel, then displays: This device cannot be managed via the video/kbd/mouse interface. The video is now disabled. You may access the management functions from your web browser. Only, none of the other PCs detect it, so no browser can find it! I have checked all cables, and all LEDs indicate there's a connection. I have installed the windows "iscsi" and the adaptec "Snap Server Manager" on all PCs but still it's not detected. I don't know what else to do, please advise!

Read the article
Fine control over zoom and aspect ratio in VLC player

- by ashh

In VLC Player (v1.01), how do I zoom video and control aspect ratio with fine control, as is possible with Media Player Classic Home Cinema (MPCHC)? The standard zoom appears to only support double, normal, quarter size etc, not useful to me at all. An example: I play an older music video file that is in 4:3 aspect ratio. In MPCHC I can use the number pad to zoom in small increments until I have removed the left and right letterbox bars and the video fills the whole screen. I can also stretch and move the video in small increments until I am happy with the aspect ratio and position. I could continue using MPCHC, but I have two displays and really like VLC feature enabling full-screen video on the main screen and the VLC interface (menus etc) on the second. I have not found a way to do this on MPCHC, if anyone knows I'd also be interested to hear.

Read the article
Why after deleting a 110+ GB collection, my /var/lib/mongodb directory still have same size?

- by tunnuz

I am having some troubles with MongoDB and space usage. In particular, I once used to have a large collection of about 600 million records totaling 110+ GB on disk. Recently I decided to drop it because the data was outdated, to do so I dropped the collection through rockmongo's web interface. Accordingly, rockmongo doesn't show me the collection anymore, however my disk usage hasn't changed at all. Is there any clean operation which I am not aware of, which must be run in order to synchronize the database with database files on disk? I have tried to perform a "repair" but the system complains that there's not enough space on disk ... that's because it is all used by MongoDB.

Read the article

< Previous Page | 332 333 334 335 336 337 338 339 340 341 342 343 | Next Page >