Search Results

Search found 15150 results on 606 pages for 'azure services'.

Page 339/606 | < Previous Page | 335 336 337 338 339 340 341 342 343 344 345 346  | Next Page >

  • Virtual Machine Network Architecture, Isolating Public and Private Networks

    - by Mark
    I'm looking for some insight into best practices for network traffic isolation within a virtual environment, specifically under VMWARE ESXi. Currently I have (in testing) 1 hardware server running ESXi but i expect to expand this to multiple pieces of hardware. The current setup is as follows: 1 pfsense VM, this VM accepts all outside (WAN/internet) traffic and performs firewall/port forwarding/NAT functionality. I have multiple public IP addresses sent to the this VM that are used for access to individual servers (via per incoming IP port forwarding rules). This VM is attached to the private (virtual) network that all other VMs are on. It also manages a VPN link into the private network with some access restrictions. This isn't the perimeter firewall but rather the firewall for this virtual pool only. I have 3 VMs that communicate with each other, as well as have some public access requirements: 1 LAMP server running an eCommerce site, public internet accessible 1 accounting server, access via windows server 2008 RDS services for remote access by users 1 inventory/warehouse management server, VPN to client terminals in warehouses These servers constantly talk with each other for data synchronization. Currently all the servers are on the same subnet/virtual network and connected to the internet through the pfsense VM. The pfsense firewall uses port forwarding and NAT to allow outside access to the servers for services and for server access to the internet. My main question is this: Is there a security benefit to adding a second virtual network adapter to each server and controlling traffic such that all server to server communication is on one separate virtual network, while any access to the outside world is routed through the other network adapter, through the firewall, and on the the internet. This is the type of architecture i would use if these were all physical servers, but i'm unsure if the networks being virtual changes the way i should approach locking down this system. Thank you for any thoughts or direction to any appropriate literature.

    Read the article

  • Windows memory logged on vs logged off

    - by Adi
    Let's say I power on my fresh installed Windows 7 x64 machine. After Windows boots up, there are a bunch of services being started in the background that start allocating memory. Then I enter my user/pass and Windows logs me in. Let's supose I don't do anythig else (I don't explicitely start any application) and I don't have any other app installed by me. So it's fresh install of my machine. My question is: how much memory is needed for all the UI & other stuff? Is it a good indicator to look into task manager and check all the processes started under my user name and sum up all the memory consumed by those processes to get the total amount of memory I am consuming just to stay logged on? Basically this is my question: how much memory is needed just to stay logged on? Now, if log off would all the memory be released back to the system so that the background services can benefit of? Also, I assume that there might be a different discussion for each Windows flavors (?)

    Read the article

  • How do I register a service with Bonjour?

    - by Roman
    I am trying to start to use Bonjour. Here I found a manual how to register a service with Bonjour. The following is written there: The network services architecture in Bonjour includes an easy-to-use mechanism for publishing, discovering, and using IP-based services. Well let's see how to register a service. In the very beginning it is written: To publish a service, an application or device must register the service with a Multicast DNS responder But how?!?! First of all I do not know what is the Multicast DNS responder. Second, it is not written how do I do it. Where and what should I type? Should I use command line? Should I use some programming languages? What exactly should I type... Is there an easy way to start to use Bonjour? Well, it was emphasized several times how easy it should be to use it. But I cannot start to use it for several day. So, can anybody, pleas, help me with that?

    Read the article

  • How can I tell my dd-wrt router to use someone's Amazon Affiliates link when I point my browser to amazon.com?

    - by Michael Paul
    Here's what I'd like to do. Instead of a one-time donation to one of my favorite free tools (junecloud.com) I'd like to do what they suggest here and use their Amazon Affiliates link to do all my Amazon shopping. I shop at amazon once or twice a week, so this is a great way to let them earn lots of long-term cash without me dropping a dime. My thought was to go into my dd-wrt enabled router and tell it, "any time I go to amazon.com on any computer in the house, please go to http://www.amazon.com/gp/redirect.html?link_code=ur2&tag=junecloud-20&camp=1789&creative=9325&location=%2F instead. (That URL simply redirects me to amazon.com but every purchase I make during that session is credited to JuneCloud.) Once logged into dd-wrt, I went to Services Services DNSMasq but I'm not really sure how to get it to work from there, or if it's even possible. I know I can redirect IP addresses, but I'm looking to redirect someone on my network from amazon.com to the special amazon affiliate code link. Hope that's clear. Thanks for any replies!

    Read the article

  • Local references to old server name remain after Windows 2003 server rename

    - by imagodei
    I have a standalone Win 2003 server with Windows Sharepoint Services (WSS3) running on it. I had to rename the server and I had bunch of problems resulting from this. Note that the server is not in AD environment. Most obvious problems were with Sharepoint, which didn't work. I was somewhat naive to think it will work in the first place, but OK - I've solved this using step 1 & 3 from this site (TNX) Other curious behavior/problems remain. Most disturbing is that Sharepoint isn't able to send email notifications to participants. I noticed there are several references to old server name everywhere I look: in Registry, in Windows Internal Database (MICROSOFT##SSEE). I see instances of old server name in the Sharepoint Central Administration - Operations - Servers in farm. There is reference to a servers: oldname.domain.local oldname.local On one of those servers there is also Windows SharePoint Services Outgoing E-Mail Service (Stopped). Also, when I try to telnet locally to the mail server (Simple Mail Transfer Protocol (SMTP) service), I get a response: 220 oldname.domain.local Microsoft ESMTP MAIL Service, Version: 6.0.3790.4675 ready at Tue, 15 Jun 2010 13:56:19 +0200 IMO these strange naming problems are also the reason why email notifications from within Sharepoint don't work. Can anyone tell me how to correct/replace those references to oldservername? Why is the email service insisting on old name? Of course I would like to try it without reinstalling the server. TNX!

    Read the article

  • Cannot establish XMPP server-to-server connection with gmail

    - by v_2e
    My jabber-server fails to connect to gmail.com giving the error: outgoing s2s stream myserver.com.ua-bot.talk.google.com closed: undefined-condition (myserver.com.ua is a Google Apps Domain with Talk service enabled.) I am using the Prosody XMPP server. It works just fine with other jabber-servers I tested so far (e.g. jabber.ru). However, when some of my clients tries to add a gmail contact to his contact-list, the subscription request lasts forever, and the Prosody gives the following sequence of messages in its log: Oct 21 22:57:16 s2sout95897f8 info Beginning new connection attempt to gmail.com ([173.194.70.125]:5269) Oct 21 22:57:16 s2sout95897f8 info sent dialback key on outgoing s2s stream Oct 21 22:57:16 s2sout95897f8 info Session closed by remote with error: undefined-condition (myserver.com.ua is a Google Apps Domain with Talk service enabled.) Oct 21 22:57:16 s2sout95897f8 info outgoing s2s stream myserver.com.ua->gmail.com closed: undefined-condition (myserver.com.ua is a Google Apps Domain with Talk service enabled.) Oct 21 22:57:16 s2sout95897f8 info sending error replies for 2 queued stanzas because of failed outgoing connection to gmail.com Here for the domain name of my server I use myserver.com.ua I found a similar problem described in this thread, but there is no detailed description of the solution there. As for the Google services, I did have a google account where I added the domain name under question to the Webmasters tools page. However, I deleted my account long ago, so now it is unclear, how any of the Google services can relate to my domain name. So my question is: What is the real cause of this problem (my jabber-server configuration or imaginary Google account or something else) and how can I make my Prosody server connect to gmail.com jabber service?

    Read the article

  • Migrating to Windows Server 2008 R2 Domain Controllers - a few Questions/Issues

    - by Chris
    Ok so here's our setup: We have 2 Windows 2003 Domain Controllers. I am trying to replace them with Windows 2008 R2. The 2003 servers are named DC01 and DC02. The 2008 R2 servers are DC1 and DC2. I prepared the Windows Server 2003 Forest Schema for a Domain Controller that runs Windows Server 2008 or Windows Server 2008 R2. Then with both of the new servers up as member servers I ran dcpromo on DC1 using the advanced option and added it successfully to my existing domain. It's roles are GC, DNS and Active Directory Domain Services. I transferred The PDC Emulator, RID Pool Manager, and Infrastructure Master roles to DC1. The Schema Master and Domain Naming master are still on DC01. The first issue that I'm encountering is when I dcpromo the DC2 and select "Replicate data over the network from and existing domain controller" I select that I want to replicate from DC1 and I get the following error: Failed to identify the requested replica partner (dc1.xxx.org) as a valid domain controller with a machine account for (DC2$). This is likely due to either the machine account not being replicated to this domain controller because of replication latency or the domain controller not advertising the Active Directory Domain Services. Please consider retrying the operation with \dc01.xxx.org as the replica partner. "The server is unwilling to process the request. Is this because the Schema Master and Domain Naming Master roles are still on the old DC01? And if so, if I transfer Schema Master and Domain Naming Master roles to DC1 what is the risk or breaking my AD? I'm a little paranoid because this process HAS to be transparent. ANY down time or interruption will result in me getting a verbal ass kicking from my I.T. Director. Both of the new servers DNS point the the old DNS servers (DC01 and DC02) not themselves by the way.

    Read the article

  • Windows 7 Aero theme's "greyed out" - no found fix

    - by Robsta
    Brand new machine that was working fine then randomly it changed the theme when I booted into a sort of "basic" theme (white task bar, no see through windows etc) I've done and attempted many fixes and I still don't understand why it doesn't work. I've tried these two solutions: "How to enable Windows 7 Aero Theme" and "Windows 7 Aero Themes Greyed out" These solutions included registy changes, stopping/starting services, and force starting the aero theme. The closest I got seems to be when I went into: Control panel (category view) Find and fix problems (System and Security) Display Aero Desktop Effects I follow through the wizard and let it do its thing and then I get an error window that pops up: Personalization - "This theme can't be applied to the desktop. Try clicking a diffrent theme." That's what I get from the wizard. What can I do? My drivers are all up to date, there are no viruses on the computer, directx is installed and updated, and the registry is all correct. EDIT: When I boot the computer, I get a notification stating that windows failed to communicate with the windows desktop services.

    Read the article

  • Enabled Network Discovery on Server, and now VNC and Squeezebox clients don't work

    - by Mike Hanson
    I've recently setup a Windows Server 2008. It's running an email server, Squeezebox server, MS SQL Server, etc. I'm doing remote maintenance with UltraVNC. I had everything working fine. Then the server needed to access a network share on another machine, and I was prompted to turn on network discovery, which I did. I chose the Home rather than Public option. Since doing that, some things have stopped working, while others are still fine. Shared folders and the the Email services (ports 25 and 110) are still accessible. VNC (port 5900) and Squeezeboxes (port 9000) no longer work. Here's what I've tried to try to solve the problem: Checked the network discovery settings, to see if anything looked strange. Checked the firewall settings, and those ports appear to be open. Also in the firewall settings, the entries for Private domain Network Discovery were all on, but the Domain/Public ones were off. I tried turning those on. In the services, turned on Function Discovery Resource Publication and SSDP Discovery. Any other suggestions?

    Read the article

  • Automating first time login process in Windows Server 2008 R2 SP1 virtual machine

    - by George Durzi
    I have a set of Windows 2008 Server R2 SP1 Enterprise Edition virtual machines running in Hyper-V. The host server has 64GB of RAM and two SSD drives (one drive for the host OS, and the second one for the VMs). The virtual machines are as follows: Domain Controller: 4GB RAM Exchange Server: 4GB RAM Terminal Services: 50GB RAM We use this setup for a travelling training class where users remote desktop to one of the VMs - let's call it the Terminal Services or "TS" VM - where tools such as Visual Studio are installed. The students go through some labs on the TS VMs in Visual Studio. Overall, this setup works great. However, when users are collectively logging in for the first time, the VM really struggles to keep up while all the user profiles are created. It can take some users up to 10 minutes to login. The number varies from 30 to 40 students. A workaround to this would be to manually remote desktop to the TS virtual machine using all the accounts to ensure that the local profile is created in advance. I'm looking for a way to automate the first time login process on the TS virtual machine. I am envisioning iterating through the accounts in a certain Active Directory OU, and then somehow initiating a remote desktop session to the TS VM to log them in for the first time. Are there ways to do this? Thanks

    Read the article

  • Disabling LDAP Signing on Windows PDC in Local Policy

    - by Golmaal
    I just tripped over my own feet it seems. Playing around on a Windows 2008 R2 server (set up as domain controller), I was intrigued by certain warning event (event id 2886) which says: "To enhance the security of directory servers, you can configure both Active Directory Domain Services (AD DS) and Active Directory Lightweight Directory Services (AD LDS) to require signed Lightweight Directory Access Protocol (LDAP) binds." So I thoughtlessly did some Googling and set the relevant policies which enforce LDAP signing. Now I don't remember but I may have done that using Local Policy. Now I have setup a pfsense box which must authenticate AD users via LDAP. While the firewall can communicate over secure channel, it is difficult to manage the same for other packages such as Squid and SquidGuard. So now I have to disable i.e. undo those policy changes. The problem is that they are greyed out! The policies in question are LDAP server signing and LDAP client signing. I don't remember what I did but when I access these policies from Local Policy editor on the server, they are set to "Require Signing" and are greyed out. The same policies can still be set via Default Domain Controller option in Group Policy editor. So how can I reset these greyed out policies? Thanks

    Read the article

  • How does Tunlr work?

    - by gravyface
    For those of you not in the US, Tunlr uses DNS witchcraft to allow you to access US-only (and UK-only stuff like BBC radio online) services and Websites like Hulu.com, etc. without using traditional methods like a VPN or Web proxy. From their FAQ: Tunlr does not provide a virtual private network (VPN). Tunlr is a DNS (domain name system) unblocking service. We’re using sophisticated technologies (a.k.a. the Tunlr Secret Sauce ©) to re-adress certain data envelopes, tricking the receiver into thinking the envelope originated from within the U.S. For these data envelopes, Tunlr is transparently creating a network tunnel from your location to our U.S.-based servers. Any data that’s not directly related to the video or music content providers which Tunlr supports is not only left untouched, it’s also not even routed through Tunlr. In order to use Tunlr, you will have to change the DNS address. See Get started for more information. I can't really wrap my head around how this works; I have always assumed that these services performed a geolocation lookup via your client IP. Just really curious as to how this works. EDIT 2 I believe they're only proxying the initial geo check and then modifying the data stream request to include your real IP address so that the streaming is direct, not proxied.

    Read the article

  • Sending mail results in "Sender address rejected: Domain not found"

    - by user1281413
    The setup: WHM/CPanel CentOS 5 server running Exim and Courier for mail services, and BIND for domain name services. I recently moved servers. The old server was running a HIGHLY similar configuration, and all accounts were ported via WHM. However, the server is unable to send, and sometimes receive email. Errors I am seeing (when I do get an error mail back) state: 450 4.1.8 : Sender address rejected: Domain not found Edit for clarity: this is the error response from remote mail servers. Numerous independent mail servers come back with the same error. (Email address is merely one valid example) My first instinct of course was to check the domain records. However, k-t.org appears to have a valid record (including an MX record), even after running it through domain checks on a completely different server elsewhere and online. Note that the issue appears to happen with all the domains hosted on the server, not just k-t.org I have also ensured that a PTR was created. My Googling has only lead me to people who had fairly basic DNS mistakes, but either I'm blind/dumb (possible, DNS is not my strong suite), or it's something that is a bit more archaic. I've run out of ideas, and I can't seem to find anything that could explain why servers are unable to resolve the domains. There doesn't seem to be anything missing or incorrect.

    Read the article

  • In Icinga (Nagios), how do I configure hosts with multiple IPs?

    - by gertvdijk
    I'm setting up Icinga (Nagios fork) and I have some machines with multiple interfaces. Some services are only listening on one of them and to check them correctly, I like to know if it's possible to have multiple IP addresses configured for a single host in Icinga. Here's a minimal example: Remote Server: eth0: 1.2.3.4 (public IP) eth1: 10.1.2.3 (private IP, secure tunnel) Apache listening on 1.2.3.4:80. (public only) OpenSSH listening on 10.1.2.3:22. (internal network only) Postfix SMTP listening on 0.0.0.0:25 (all interfaces) Icinga Server: eth0: 10.2.3.4 (private IP, internet access) Now if I define a host: define host { use generic-host host_name server1 alias server1.gertvandijk.net address 10.1.2.3 } This will not check the HTTP status correctly. And defining an additional host: define host { use generic-host host_name server1-public alias server1.gertvandijk.net address 1.2.3.4 } will check everything, but shows up as two independent hosts. Now I want to 'aggregate' these two hosts to show up as a single host, yet providing an easy configuration to check the services on their proper address. What is the most elegant number-of-configuration-lines-saving solution to this? I read about several plugins available to workaround this, but I can't figure out what is the current way to address it. Solutions go back to 2003, but I'm running Icinga 1.7.1, already capable of the address6 option, yet that triggers IPv6-only resolving on the hostname... Ideally, I wish to configure Icinga to be intelligent enough to know that the Postfix instance running on 10.1.2.3:25 is the same as 1.2.3.4:25 and thus not triggering two alarms. I guess this must have been tackled before and sysadmins have it set up now. Please share your solution to this. Thanks! :)

    Read the article

  • AJP Connector Apache-Tomcat with php and java application

    - by Safari
    I have a question about proxy and ajp module. On my machine I have a Apache web server and a Tomcat servlet container. On Tomcat is running a my java webapplication. On Apache I have some services and I can call these in this way: http://myhos/service1 http://myhos/service2 http://myhos/service3 I would configurate a ajp connector to call my tomcat webapplication from Apache. I would somethin as http://myhost to call the Tomcat webapp. So, I configurated my apache in this way..and I have what I wanted: I can use http://myHost to visualize the Tomcat webApp by Apache. <VirtualHost *:80> ProxyRequests off ProxyPreserveHost On ServerAlias myserveralias ErrorLog logs/error.log CustomLog logs/access.log common <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /server-status ! ProxyPass /balancer-manager ! ProxyPass / balancer://mycluster/ stickysession=JSESSIONID nofailover=Off maxattempts=1 <Proxy balancer://mycluster> BalancerMember ajp://myIp:8009 min=10 max=100 route=portale loadfactor=1 ProxySet lbmethod=bytraffic </Proxy> <Location /balancer-manager> SetHandler balancer-manager Order deny,allow Allow from localhost </Location> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent </VirtualHost> But, now I can't use the apache services: If I use http://myhos/service1 I have an error because apache try to search service1 on my tomcatWebApp. Is there a way to fix it?

    Read the article

  • Mongo daemon restarts after replica set issue

    - by Matt Beckman
    We had a recent election in our replica set (2 read nodes; 1 write node) that changed the primary node. Curious as to why this occurred, I started looking through the logs to find out what happened. It appears that mongoNode2 could not communicate with mongoNode3. When both nodes could not communicate, it appears that this caused the services on mongoNode2 and mongoNode3 to restart, eventually resulting in a new primary after the services had been started again. Thu Jun 23 08:27:28 [ReplSetHealthPollTask] DBClientCursor::init call() failed Thu Jun 23 08:27:28 [ReplSetHealthPollTask] replSet info mongoNode3:27017 is down (or \ slow to respond): DBClientBase::findOne: transport error: mongoNode3:27017 query: { \ replSetHeartbeat: "myReplSet", v: 3, pv: 1, checkEmpty: false, from: \ "mongoNode2:27017" } Thu Jun 23 08:27:29 got kill or ctrl c or hup signal 15 (Terminated), will \ terminate after current cmd ends Thu Jun 23 08:27:29 [interruptThread] now exiting Thu Jun 23 08:27:29 dbexit: Is there any reason that the mongo service would restart due to a DBClientCursor::init call() failure? Is this a known bug? It should be noted that mongoNode2 and mongoNode3 are VMs on the same VMware host. MongoNode1 is not on the same host, and it did not have any issues with the service. However, I did not have any other reports of issues with other VMs on the VMware host.

    Read the article

  • certutil -ping fails with 30 seconds timeout - what to do?

    - by mark
    Dear ladies and sirs. The certificate store on my Win7 box is constantly hanging. Observe: C:\1.cmd C:\certutil -? | findstr /i ping -ping -- Ping Active Directory Certificate Services Request interface -pingadmin -- Ping Active Directory Certificate Services Admin interface C:\set PROMPT=$P($t)$G C:\(13:04:28.57)certutil -ping CertUtil: -ping command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. C:\(13:04:58.68)certutil -pingadmin CertUtil: -pingadmin command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. C:\(13:05:28.79)set PROMPT=$P$G C:\ Explanations: The first command shows you that there are –ping and –pingadmin parameters to certutil Trying any ping parameter fails with 30 seconds timeout (the current time is seen in the prompt) This is a serious problem. It screws all the secure communication in my app. If anyone knows how this can be fixed - please share. Thanks. P.S. 1.cmd is simply a batch of these commands: certutil -? | findstr /i ping set PROMPT=$P($t)$G certutil -ping certutil -pingadmin set PROMPT=$P$G

    Read the article

  • Web Hosting: Any web host that supports files more than 50,000 in number?

    - by Devner
    Hi all, For my PHP & mySQL based application, I am trying to buy website hosting from a host who does not have a limit on the number of files I carry in my hosting account. Almost all the websites have a common limit of 50,000 files (some websites call it 50,000 nodes). The rest(to the extent of my search) are not even close. I have gone through the various websites, Googled lot of information, have spoken with the customer service of the hosting companies and they said that they have a limit of 50,000 files and that's why they call it the LIMIT. Now I have my application, which is a kind of social networking website, where people can upload various files of varying file size. So say if 50,000 users were to join the website and upload 1 file each, the limit of 50,000 will be reached very easily and my 50,001 customer will start facing file upload problems (& so will my account). So I would like to know if there's any website hosting services that do NOT levy such restrictions. In summary, I need the following options: No maximum file limit (more than 50,000 files in account). No maximum file upload limit in server setting (10MB, 12MB, 15MB, 20MB, etc.). Ability to upload files of various types (zip, flv, jg, png, etc.). Ability to stream Audio and Video (live audio & video not necessary). Access to .htaccess Access to php.ini, my.cnf or my.ini (this would be a plus) Supports SSL. Provides dedicated hosting(& IP) as well. Monthly payments without contracts are a plus. If you know of any such website hosting services, please post a reply ( a link to the same will be appreciated ). Thank you.

    Read the article

  • Unable to connect to second name of Windows 2008 Server R2 machine from XP

    - by Tumba
    I used the command netdom computername /add:newname.domainname.com to add a second name to a server running Windows 2008 Server R2. After restarting the server, I had DNS "A" entries for both names. In addition, the second name was added to HKLM\SYSTEM\CurrentControlSet\services\LanmanServer\Parameters\OptionalNames, which I believe should have taken care of any NetBIOS resolution. From my Windows 7 workstation, I can ping both names and running net view on both names reveals the same list of resources. From Windows XP, I can ping both names, but net view only works on the first name. Running net view on the second name returns: System error 52 has occurred. You were not connected because a duplicate name exists on the network. Go to System in Control Panel to change the computer name and try again. What do I need to do to make the second name usable from XP clients? Update: I was able to resolve the problem by adding the REG_DWORD key DisableStrictNameChecking = 1 to HKLM\SYSTEM\CurrentControlSet\services\LanmanServer\Parameters, then restarting the Server service. However, I do not understand why this was necessary.

    Read the article

  • Cisco ASA user authentication options - OpenID, public RSA sig, others?

    - by Ryan
    My organization has a Cisco ASA 5510 which I have made act as a firewall/gateway for one of our offices. Most resources a remote user would come looking for exist inside. I've implemented the usual deal - basic inside networks with outbound NAT, one primary outside interface with some secondary public IPs in the PAT pool for public-facing services, a couple site-to-site IPSec links to other branches, etc. - and I'm working now on VPN. I have the WebVPN (clientless SSL VPN) working and even traversing the site-to-site links. At the moment I'm leaving a legacy OpenVPN AS in place for thick client VPN. What I would like to do is standardize on an authentication method for all VPN then switch to the Cisco's IPSec thick VPN server. I'm trying to figure out what's really possible for authentication for these VPN users (thick client and clientless). My organization uses Google Apps and we already use dotnetopenauth to authenticate users for a couple internal services. I'd like to be able to do the same thing for thin and thick VPN. Alternatively a signature-based solution using RSA public keypairs (ssh-keygen type) would be useful to identify user@hardware. I'm trying to get away from legacy username/password auth especially if it's internal to the Cisco (just another password set to manage and for users to forget). I know I can map against an existing LDAP server but we have LDAP accounts created for only about 10% of the user base (mostly developers for Linux shell access). I guess what I'm looking for is a piece of middleware which appears to the Cisco as an LDAP server but will interface with the user's existing OpenID identity. Nothing I've seen in the Cisco suggests it can do this natively. But RSA public keys would be a runner-up, and much much better than standalone or even LDAP auth. What's really practical here?

    Read the article

  • Windows 7 System File Checker (sfc) not working

    - by Andrew
    I have a strange problem with Windows 7 RTM. I'm running Ultimate 64-bit edition. Whenever I run sfc /scannow I get this error: Windows Resource Protection could not start the repair service. My research so far has told me that I need to set the Windows Module Installer and Windows Installer services' startup types to Manual. They already were, so I manually started those services and tried again. No luck. I've even booted into my Windows 7 repair disc and tried running sfc /scannow from that. All I get is this: A repair operation is already pending. Restart and try again. History: I'm trying to run sfc because I am unable to open any images in Windows Photo Viewer. Whenever I try, I get the error "Class not registered." I believe the problem started after I installed Gladinet, but I can't be sure. I've uninstalled Gladinet, but the problem remains. System Restore was disabled (yes, I know I'm stupid - you don't have to remind me). Please help. Thanks.

    Read the article

  • Disable or remove filter driver for single HID device

    - by snoopen
    Running Windows XP in a corporate setting here. I have an issue where a filter driver is interfering with the functionality of different USB HIDs. For example graphics tablets do not respond while the filter driver is in place. I've also had the issue with foot pedals used with transcription software. My question is really two fold: A) what makes Windows use a filter driver on one HID but not another? B) when a filter driver is causing conflicts how can I disable it on the affected devices? Background I've previously narrowed down the issue to the filter driver by uninstalling the software (Funk Proxy Host) responsible for the filter driver. The software is a type of RDP we use here at work. (I might have even booted into safe mode and renamed the file, I forget). I believe the filter driver is present to disable or modify the use of the local keyboard and mouse while admin staff are assisting users. Either way I don't have the authority to just go uninstalling this software. As far as I can tell the software versions are the same, however I'm not sure if the device driver definitions are all the same as I don't know where these things would be located. To check for the presence of the filter driver I locate the hardware device in Device Manager, click Properties Driver tab Driver Details.... It shows up as ph32ihid.sys. Even though all machines are meant to have the same SOE and do have Funk Proxy Host installed I don't always have issues with the same HIDs. A few machines here the foot pedals without any issues. I've not had any machines work with the graphics tablet without uninstalling Funk software. Driver details I've just read up a bit more about filter drivers and found the drivers description in the registry under "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\ProxyHostHIDFilter" There it's called "Kernel-mode HID filter driver for the Proxy Host". Presumably I could also disable it here but that would be system wide which is probably not desirable?

    Read the article

  • OpenVPN-based VPN server on same system it's "protecting": feasible?

    - by Johnny Utahh
    Scenario: hosted machine (typically a VPS) serving wiki, svn, git, forums, email lists (eg: GNU mailman), Bugzilla (etc) privately to < 20 people. People not on team not allowed access. Seeking VPN-restricted access to said server. Have good user experience with OpenVPN-based servers/clients, but have yet to server-admin such systems. Otherwise, experienced Linux sysadmin. Target system: Ubuntu, probably 12.04. Seeking to put an OpenVPN process on above server to "protect" all the above-mentioned services, enabling only OpenVPN-authorized clients/processes to access above services. (Can easily acquire additional IP address(es) as needed for this setup.) Option: if absolutely needed, can employ an additional, dedicated, "VPN server" VPS simply to be my VPN server "front end." But prefer to have all server processes (VPN server plus other server apps) all running on same machine, if possible. Will consider further if dedicated-VPN-machine setup enables 1. easier installation/administration, 2. better/easier end-user experience, and/or 3. makes system significantly more secure. Any of above feasible? The main intention: create a VPN from purely-hosted resources, and not spend all the effort to make a non-VPN, secure site--which typically means "SSL wrapping" + all the continual webserver-application-update management. Let the VPN server deal with access security, and spend list time pushing said security "down" in the other apps/Apache.

    Read the article

  • Using Active Directory through a Firewall

    - by Adam Brand
    I had kind of a weird setup today where I wanted to enable Windows Firewall on a Windows 2003 R2 SP2 computer that would act as an Active Directory Domain Controller. I didn't see one resource on the Internet that listed what would be required to do this, so I thought I'd list them here and see if anyone has anything to add/sees something that isn't necessary. Ports to Open with "subnet" scope: 42 | TCP | WINS (if you use it) 53 | TCP | DNS 53 | UDP | DNS 88 | TCP | Kerberos 88 | UDP | Kerberos 123 | UDP | NTP 135 | TCP | RPC 135 | UDP | RPC 137 | UDP | NetBIOS 138 | UDP | NetBIOS 139 | TCP | NetBIOS 389 | TCP | LDAP 389 | UDP | LDAP 445 | TCP | SMB 445 | UDP | SMB 636 | TCP | LDAPS 3268 | TCP | GC LDAP 3269 | TCP | GC LDAP Ports to Open with "Any" Scope (for DHCP) 67 | UDP | DHCP 2535 | UDP | DHCP ALSO You need to restrict RPC to use fixed ports instead of everything 1024. For that, you need to add two registry keys: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\NTDS\Parameters Registry value: TCP/IP Port Value type: REG_DWORD Value data: <-- pick a port like 1600 and put it here HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Netlogon\Parameters Registry value: DCTcpipPort Value type: REG_DWORD Value data: <-- pick another port like 1650 and put it here ...don't forget to add entries in the firewall to allow those in (TCP, Subnet scope). After doing all that, I was able to add a client computer to the AD domain (behind Windows Firewall) and log in successfully.

    Read the article

  • Is there a faster way to change default apps associated with file types on OS X?

    - by Lri
    Is there anything more convenient than using RCDefaultApp or Magic Launch, or just repeatedly pressing the Change All buttons in Finder's information panels? I thought about writing a shell script that would modify the CFBundleDocumentTypes arrays in Info.plist files. But each app has multiple keys (sometimes an icon) that would need to be changed. lsregister can't be used to make specific modifications to the Launch Services database. $ `locate lsregister` -h lsregister: [OPTIONS] [ <path>... ] [ -apps <domain>[,domain]... ] [ -libs <domain>[,domain]... ] [ -all <domain>[,domain]... ] Paths are searched for applications to register with the Launch Service database. Valid domains are "system", "local", "network" and "user". Domains can also be specified using only the first letter. -kill Reset the Launch Services database before doing anything else -seed If database isn't seeded, scan default locations for applications and libraries to register -lint Print information about plist errors while registering bundles -convert Register apps found in older LS database files -lazy n Sleep for n seconds before registering/scanning -r Recursive directory scan, do not recurse into packages or invisible directories -R Recursive directory scan, descending into packages and invisible directories -f force-update registration even if mod date is unchanged -u unregister instead of register -v Display progress information -dump Display full database contents after registration -h Display this help

    Read the article

< Previous Page | 335 336 337 338 339 340 341 342 343 344 345 346  | Next Page >