Search Results

Search found 42297 results on 1692 pages for 'run'.

Page 339/1692 | < Previous Page | 335 336 337 338 339 340 341 342 343 344 345 346  | Next Page >

• Dock with dual external DVI monitors with Intel + Nvidia Optimus?

  - by Ryan

  I have a Dell Latitude E6420 laptop plugged into a docking station, and the dock has 2 monitors (connected with DVI). Also note that I've installed Ubuntu alongside (dual-boot) Windows 7. I can't get the dual monitors to work both on Ubuntu (either 11.10 or 12.04) and Windows 7. When I run lspci | grep VGA, I get: 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: nVidia Corporation GF108 [Quadro NVS 4200M] (rev a1) If I then reboot and uncheck Optimus setting in the BIOS during reboot, I'm able to get the dual monitors to work in Ubuntu 12.04 (but I need to configure them every boot in Nvidia Settings). When I run lspci | grep VGA, I get: 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [Quadro NVS 4200M] (rev a1) But then if I reboot into Windows (leaving the Optimus unchecked), Windows can't detect external monitors, and the resolution is unacceptably low. I've seen on many forum posts that this particular graphics card setup causes lots of headaches. I haven't been able to resolve my problem yet. How can I use my external display on my laptop with intel and nvidia video cards? How to use external displays with Intel driver on a NVidia/Intel hybrid system nVidia Optimus , Unity 3D and Dual Monitors "Just use VGA instead of DVI" isn't an option because my dock has only 1 VGA port (and 2 DVI). Switching the BIOS setting on every reboot and then reconfiguring the display settings every time is tedious, time-consuming, and impractical. Do you know how to make this work smoothly? Thanks for your help! P.S. see also: http://superuser.com/questions/434358/dell-latitude-e6420-dual-boot-ubuntu-windows-7-optimus-graphics-problems

  Read the article

• updatedb & locate command problem - Files from external hard drive are no longer indexed after rebooting

  - by user784637

  Files from my external hard drive are no longer indexed after rebooting. I have to remount and then run # updatedb after each reboot. The problem is updatedb takes a few minutes for my external hard drives. Is there any way I can retain indexing for my externals after I reboot so that the locate command can search through my externals? EDIT: Per Request here are my specs: $ cat /etc/updatedb.conf PRUNE_BIND_MOUNTS="yes" # PRUNENAMES=".git .bzr .hg .svn" PRUNEPATHS="/tmp /var/spool /media" PRUNEFS="NFS nfs nfs4 rpc_pipefs afs binfmt_misc proc smbfs autofs iso9660 ncpfs coda devpts ftpfs devfs mfs shfs sysfs cifs lustre_lite tmpfs usbfs udf fuse.glusterfs fuse.sshfs ecryptfs fusesmb devtmpfs" # mount /dev/sda5 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/me/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=me) /dev/sdb1 on /media/me type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions) /dev/sdd1 on /media/Little Boy type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions) /dev/sde1 on /media/Fat Man type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions) # on_ac_power; echo $? 255

  Read the article

• Struggling to get set up with JOGL2.0

  - by thecoshman

  I guess that Game Dev' is a more sensible place for my problem then SO. I did have JOGL1.1 set up and working, but I soon discovered that it did not support the latest OpenGL, so I started work on upgrading to JOGL2.0 it's not gone too well. Firstly, is it worth me trying to get JOGL to work, or should I just move over to LWJGL? I am fairly comfortable with OpenGL (via C++) and from what I did get working with JOGL1.1, I seem to be OK adapting to it. Assuming that I stick with JOGL, am I foolish for trying to use JOGL2.0? From what I can gather, JOGL2.0 is still in beta, but I am willing to go with it as I want to make use of the latest OpenGL I can. I have been using the Eclipse IDE and have set up a user library for JOGL, here is a screen shot of the configuration and I have added this user library to my own Eclipse project. the system variable %JOGL_HOME% points to "C:\Users\edacosh\Downloads\JOGL2.0" so that should work fine. Now, the problem I actually having, when I try to run my code, on the line GLProfile glp = GLProfile.getDefault(); The code stops with the following message... Exception in thread "main" java.lang.NoClassDefFoundError: com/jogamp/common/jvm/JVMUtil at javax.media.opengl.GLProfile.<clinit>(GLProfile.java:1145) at DiCE.DiCE.<init>(DiCE.java:33) at App.<init>(App.java:17) at App.main(App.java:12) Caused by: java.lang.ClassNotFoundException: com.jogamp.common.jvm.JVMUtil at java.net.URLClassLoader$1.run(Unknown Source) at java.security.AccessController.doPrivileged(Native Method) at java.net.URLClassLoader.findClass(Unknown Source) at java.lang.ClassLoader.loadClass(Unknown Source) at sun.misc.Launcher$AppClassLoader.loadClass(Unknown Source) at java.lang.ClassLoader.loadClass(Unknown Source) ... 4 more I have also set my project to ensure that it is using jre6 along with jdk6, as I was having some issues. I hope I have given you enough information to be able to help me. It probably doesn't help that I am rather new to Java, been developing in C++ for ages. Thanks

  Read the article

• An Interesting Perspective on Oracle's Mobile Strategy

  - by Carlos Chang

  Oracle’s well known for being an acquisitive company. On average, I think we acquire about 1 company a month. (don’t quote me, I didn't run the numbers)  With all the excitement around mobile, mobile and wait for it… mobile, well, you know...what' s up with that? Well, just to be clear and quote Schultz from Hogan's Heroes "I know nothing! Nothing! "  But I did recently run across this blog by Kevin Benedict over at mobileenterprisestrategies.com covering this very topic, Oracle Mobility Emerges Prepared for the Future,  a little (fair use) snippet here:"History, however, may reward Oracle's patience.  While veteran mobile platform vendors (including SAP) have struggled to keep up with the fast changing market, R&D investment requirements, the fickle preferences of mobile developers, and the emergence of cloud-based mobile services, Oracle has kept their focus on supporting mobile developers with integration services and tools that extend their solutions out to mobile apps.”It’s an interesting read, and I would encourage you to check it out here.   BTW, if you’re a Twitter user, follow our new account @OracleMobile To the first ten thousand followers, I bequeath you my sincere virtual thanks and gratitude. :)  For the dedicated mobile blog, go to blogs.oracle.com/mobile.

  Read the article

• WARNING Retrying Bulk Insert for file:sqlldr due to Communication Error:256

  - by user702295

  WARNING Retrying Bulk Insert for file:sqlldr due to Communication Error:256 I am running my engine on Linux and am receiving an intermittent message "WARNING Retrying bulk insert for file: sqlldr due to communication Error: 256" The engine seems to have completed successfully, but it is not clear if this error caused some of the forecast to not complete. It is also not clear what caused the error. Generally if you see only the WARNING of it, it means that next retries of the same load request have eventually succeeded and so the run a a whole is not affected. In order to know more about what happens, look for .log/.bad files left in the engines bin directory or possibly a quote of them within the specific engine log that had the issue.  The sqlnet.log file may also have some information about it and perhaps at the database server side there may be some log/alert regarding what happened.  Look at the alert.log. In general it could be that the database server/network was over loaded at the time and somehow the connection was rejected/failed/aborted either due to specific setting on concurrent connections/sessions or inadvertently due to glitch in network/os/hardware. If this repeats and becomes more frequent during the run you should look further into it as mentioned above. You can also track this using either SQL*Trace or java.util.logging.  - Globally enable logging by setting the oracle.jdbc.Trace system property java -Doracle.jdbc.Trace=true - Client Side Tracing: Your SQLNET.ORA file should contain the following lines to produce a client side trace file: trace_level_client = 10 trace_unique_client = on trace_file_client = sqlnet.trc trace_directory_client = <path_to_trace_dir> Server Side Tracing: To enable server side tracing, use the following parameters: trace_level_server = 10 trace_file_server = server.trc trace_directory_server = <path_to_trace_dir> Tracing Levels: The following values can be used for TRACE_LEVEL* parameters:     16 or SUPPORT — WorldWide Customer Support trace information     10 or ADMIN — Administration trace information     4 or USER — User trace information     0 or OFF — no tracing, the default Additional information is readily available via the web.

  Read the article

• what could cause a script to fail to find python when it has `#!/usr/bin/env python` in the first line?

  - by jcollum

  Trying to get casperjs running on Ubuntu 12.04. After installing it when I run I get: 09:20 $ ll /usr/local/bin/casperjs lrwxrwxrwx 1 root root 26 Nov 6 16:49 /usr/local/bin/casperjs -> /opt/casperjs/bin/casperjs 09:20 $ /usr/bin/env python --version Python 2.7.3 09:20 $ cat /opt/casperjs/bin/casperjs | head -4 #!/usr/bin/env python import os import sys 09:20 $ casperjs : No such file or directory 09: 22 $ python Python 2.7.3 (default, Sep 26 2013, 20:03:06) [GCC 4.6.3] on linux2 So Python is present and runnable, casperjs is pointing to the right place and it is a python script. But when I run it I get "No such file". I can fix it by changing the first line of the casperjs python file from: #!/usr/bin/env python to: #!/usr/bin/python Result: $ casperjs --version 1.1.0-DEV I managed to fix it, but I'm wondering why it didn't work with #!/usr/bin/env python, since that seems to be a normal interpreter line. Do I have something configured wrong? Here are the steps to get casperjs: $ git clone git://github.com/n1k0/casperjs.git $ cd casperjs $ ln -sf `pwd`/bin/casperjs /usr/local/bin/casperjs $ casperjs : No such file or directory

  Read the article

• Windows Azure Virtual Machines - Make Sure You Follow the Documentation

  - by BuckWoody

  To create a Windows Azure Infrastructure-as-a-Service Virtual Machine you have several options. You can simply select an image from a “Gallery” which includes Windows or Linux operating systems, or even a Windows Server with pre-installed software like SQL Server. One of the advantages to Windows Azure Virtual Machines is that it is stored in a standard Hyper-V format – with the base hard-disk as a VHD. That means you can move a Virtual Machine from on-premises to Windows Azure, and then move it back again. You can even use a simple series of PowerShell scripts to do the move, or automate it with other methods. And this then leads to another very interesting option for deploying systems: you can create a server VHD, configure it with the software you want, and then run the “SYSPREP” process on it. SYSPREP is a Windows utility that essentially strips the identity from a system, and when you re-start that system it asks a few details on what you want to call it and so on. By doing this, you can essentially create your own gallery of systems, either for testing, development servers, demo systems and more. You can learn more about how to do that here: http://msdn.microsoft.com/en-us/library/windowsazure/gg465407.aspx   But there is a small issue you can run into that I wanted to make you aware of. Whenever you deploy a system to Windows Azure Virtual Machines, you must meet certain password complexity requirements. However, when you build the machine locally and SYSPREP it, you might not choose a strong password for the account you use to Remote Desktop to the machine. In that case, you might not be able to reach the system after you deploy it. Once again, the key here is reading through the instructions before you start. Check out the link I showed above, and this link: http://technet.microsoft.com/en-us/library/cc264456.aspx to make sure you understand what you want to deploy.  

  Read the article

• Should one generally develop a client library for REST services to help prevent API breakages?

  - by BestPractices

  We have a project where UI code will be developed by the same team but in a different language (Python/Django) from the services layer (REST/Java). The code for each layer exits in different code repositories and which can follow different release cycles. I'm trying to come up with a process that will prevent/reduce breaking changes in the services layer from the perspective of the UI layer. I've thought to write integration tests at the UI layer level that we'll run whenever we build the UI or the services layer (we're using Jenkins as our CI tool to build the code which is in two Git repos) and if there are failures then something in the services layer broke and the commit is not accepted. Would it also be a good idea (is it a best practice?) to have the developer of the services layer create and maintain a client library for the REST service that exists in the UI layer that they will update whenever there is a breaking change in their Service API? Conceivably, we would then have the advantage of a statically-typed API that the UI code builds against. If the client library API changes, then the UI code won't compile (so we'll know sooner that there was a breaking change). I'd also still run the integration tests upon building the UI or services layer to further validate that the integration between UI and the service(s) still works.

  Read the article

• What is the best way to code the XNA Game Server for FPS game?

  - by AgentFire

  I'm writing a FPS XNA game. It gonna be multiplayer so I came up with following: I'm making two different assemblies — one for the game logic and the second for drawing it and the game irrelevant stuff (like rocket trails). The type of the connection is client-server (not peer-to-peer), so every client at first connects to the server and then the game begins. I'm completly decided to use XNA.Framework.Game class for the clients to run their game in window (or fullscreen) and the GameComponent/DrawableGameComponent classes to store the game objects and update&draw them on each frame. Next, I want to get the answer to the question: What should I do on the server side? I got few options: Create my own Game class on the server, which will process all the game logic (only, no graphics). The reason why I am not using the standart Game class is when I call Game.Run() the white window appears and I cant figure out how to get rid of it. Use somehow the original XNA's Game class, which is already has the GameComponent collection and Update event (60 times per second, just what I need). UPDATE: I got more questions: First, what socket mode should I use? TCP or UDP? And how to actually let the client know that this packet is meant to be processed after that one? Second, if I is going to use exacly GameComponent class for the game objects which is stored and process on the server, how to make them to be drawn on the client? Inherit them (while they are combined to an assembly)? Something else?

  Read the article

• Doesn't boot after installation

  - by jchysk

  Downloaded Ubuntu 12.04.1-alternate-amd64 Installed to USB stick Integrity check fails on ./install/netboot/ubuntu-installer/amd64/pxelinux.cfg/default but that seems to be a known bug where the file isn't included in the alternative 64-bit ISO and shouldn't affect installation. I ignore it and proceed on. For partitioning on 2 SSD Drives: Partition 300MB and 63GB on both RAID1 the 300MB and 63GBs Set the 300MB to EXT4 on /boot Encrypt the rest as MD1 and set it for LVM Create two volumes from MD1: 4GB swap and 59GB to / I go through the installation and get to the point where it says everything is ready and to take the media out so as to boot from the drives I receive the error "Error: No video mode activated." on startup I've read that this can be solved by running "cp /usr/share/grub/*.pf2 /boot/grub" and then updating grub but I can't get to a place where I can actually run this command. In rescue mode I can get to a shell from installer with /boot mounted to /target. So from there I can run "cp /cdrom/boot/grub/font.pf2 /target/grub/" but can't figure out a way to get it to update grub after that or know how what to change in manually updating the grub.cfg file. If I try other devices to mount the root filesystem I get the error "An error occurred while mounting the device you entered for your root file system". It just sits on the video mode error and doesn't progress further. Googling around it seems like people see the error briefly before it continues booting, not getting stuck on it the way I am which leads me to believe that error may be unrelated to Ubuntu not booting. So any ideas as to what I should try next or what needs to be done to install Ubuntu and get it to boot would be helpful.

  Read the article

• How to install an init.d script in ubuntu?

  - by suhail

  i am trying to install an init.d script, to run celery for scheduling tasks. Here is the steps i followed: copied the file celeryd and pasted it in folder /etc/init.d/ created a configuration file celeryd in folder /etc/default/ now when i tried to start it by sudo /etc/init.d/celeryd start, it throws error sudo: /etc/init.d/celeryd: command not found I googled about how to install init.d, i got this SO-question. it says to issue a uname -a and when i does i get this: Linux capsonesystem8-desktop 3.2.0-43-generic-pae #68-Ubuntu SMP Wed May 15 03:55:10 UTC 2013 i686 i686 i386 GNU/Linux and also it says use utils like insserv to enable init.d script so tried: insserv /etc/init.d/celeryd but it throws error insserv: command not found so i tried to install insserv sudo apt-get install insserv. but it say aleady installed: insserv is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 222 not upgraded. So how to install init.d script?? Any help will be appreciated. update1: when i tried: $ sh -x /etc/init.d/celeryd start it reveal some errors. may be that is why the service won’t start. update2: I cleared all the errors when i run $ sh -x /etc/init.d/celeryd start but still sudo /etc/init.d/celeryd start throws command not found error

  Read the article

• Ubuntu security with services running from /opt

  - by thejartender

  It took me a while to understand what's going on here (I think), but can someone explain to me if there are security risks with regards to my logic of what's going on here as I am trying to set up a home web server as a developer with some good Linux knowledge? Ubuntu is not like other systems, as it has restricted the root user account. You can not log in as root or su to root. This was a problem for me as I have had to install numerous applications and services to /opt as per user documentation (XAMPPfor Linux is a good example). The problem here is that this directory is owned by root:root. I notice that my admin user account does not belong to root group through the following command: groups username so my understanding is that even though the files and services that I place in /opt belong to root, executing them by means of sudo (as required) does not mean that they are run as root? I imagine that the sudo command is hidden somewhere under belonging to the root user and has a 775 permission? So the question I have is if running a service like Tomcat, Apcahe, etc exposes my system like on other systems? Obviously I need to secure these in configurations, but isn't the golden rule to never run something as root? What happens if I have multiple services running under same user/group with regards to a compromised server?

  Read the article

• Ubuntu and racadm

  - by lmqcn

  I recently purchased a used poweredge 1850 server and it came with a DRAC card. After wiping the HDD and installing ubuntu server 12.04.3 LTS amd64 on it, I am now trying to gain access to the DRAC which I believe is version 4. I have properly configured the DRAC to use it's own IP on my LAN and when I point my browser to the IP address, I am greeted with the DRAC login page (it has the dell logo and everything). However, after trying the credentials of root/calvin, I was denied access. So I think that the previous owners had set their own password. After doing some reading, it appears that I can reset the credentials to the default using racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 newpassword but upon entering the command, I get this error: bash: /usr/sbin/racadm: No such file or directory This holds true even if I run sudo su prior to running the racadm command. If, however, I run sudo racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 newpassword there are no errors. Yet, when I try to log into the DRAC via the web interface using the credentials of root/newpassword I am still not granted access. I installed the dell utilities via the guide at https://wiki.ubuntu.com/HardwareSupportMachinesServersDellNotes. I first tried to install the 64 bit version that is on the dell repositories, but after that was unsuccessful, I just followed the guide verbatim. No errors were produced in either case. I even followed the information at the bottom of the guide by executing sudo pppd /dev/ttyS1 1382400 crtscts noipdefault noauth lock persist connect 'chat -v "" CLIENT CLIENTSERVER "\\c"' but obviously, replacing the /dev/ttyS1 with the correct information for my system. ls -l /usr/sbin/ | grep racadm yields -rwxr-xr-x 1 root root 87930 Sep 16 04:03 racadm I have tried these credentials after each attempt of changing the password: root/calvin root/newpassword admin/calvin admin/newpassword All have been unsuccessful. What is the next course of action that I should take?

  Read the article

• 12.04.1 no audio through HDMI

  - by JoJo

  having a bit of an issue with getting audio to go through HDMI. Here are the base specs: OS: Ubuntu Desktop 12.04.1 x64 CPU: AMD A10-5800K 3.8G 4M FM2 R Mobo: MSI FM2-A75MA-E35 OS: Ubuntu 12.04.1 LTS Vid Card: (integrated on CPU) AMD Radeon HD 7660D HDMI sound works fine under Win7 (after mobo and vid drivers are installed), so it's not physically broken. Audio through the normal headphone jacks works fine under Ubuntu. Looking at the audio panel, there is no HDMI output at all. aplay -l also reports only: card 0: Generic [HD-Audio Generic], device 0: ALC887-VD Analog [ALC887-VD Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 In additional drivers there are two versions: ATI/AMD PROPRIETARY FGLRX GRAPHICS DRIVER ATI/AMD PROPRIETARY FGLRX GRAPHICS DRIVER (post-release update) The first installs, but problem persists. I do get more resolutions to pick from. Second version does not, reporting it failed installation and to find details at: /var/log/jockey.log Looked at the log, and it's insanely long, if necessary I can get it to you guys. Did more research and some had luck by manually installing the drivers, so tried to give that a shot by following this: https://help.ubuntu.com/community/BinaryDriverHowto/ATI#Manually_installing_Catalyst_12.6 starting at 3.1 Manually installing Catalyst 12.6. I immediately had 2 issues, (1) the AMD website does not provide any drivers for Linux, and (2) the following command did not work: sudo sh amd-driver-installer-12-6-x86.x86_64.run --buildpkg Ubuntu/precise sh: 0: Can't open amd-driver-installer-12-6-x86.x86_64.run Some other posts stated to update "alsa-drivers", but that also did not work as install command for the new version of them did not work. I forget the exact issue, but similar to above, cannot open / cannot find. Any help would be greatly appreciated!

  Read the article

• Upgrade 10.04LTS to 10.10 problem

  - by Gopal

  Checking for a new ubuntu release Done Upgrade tool signature Done Upgrade tools Done downloading extracting 'maverick.tar.gz' authenticate 'maverick.tar.gz' against 'maverick.tar.gz.gpg' tar: Removing leading `/' from member names Reading cache Checking package manager Reading package lists... Done Building dependency tree Reading state information... Done Building data structures... Done Reading package lists... Done Building dependency tree Reading state information... Done Building data structures... Done Updating repository information WARNING: Failed to read mirror file A fatal error occurred Please report this as a bug and include the files /var/log/dist-upgrade/main.log and /var/log/dist-upgrade/apt.log in your report. The upgrade has aborted. Your original sources.list was saved in /etc/apt/sources.list.distUpgrade. Traceback (most recent call last): File "/tmp/tmpe_xVWd/maverick", line 7, in <module> sys.exit(main()) File "/tmp/tmpe_xVWd/DistUpgradeMain.py", line 158, in main if app.run(): File "/tmp/tmpe_xVWd/DistUpgradeController.py", line 1616, in run return self.fullUpgrade() File "/tmp/tmpe_xVWd/DistUpgradeController.py", line 1534, in fullUpgrade if not self.updateSourcesList(): File "/tmp/tmpe_xVWd/DistUpgradeController.py", line 664, in updateSourcesList if not self.rewriteSourcesList(mirror_check=True): File "/tmp/tmpe_xVWd/DistUpgradeController.py", line 486, in rewriteSourcesList distro.get_sources(self.sources) File "/tmp/tmpe_xVWd/distro.py", line 103, in get_sources source.template.official == True and AttributeError: 'Template' object has no attribute 'official' This is what i got when i tried to upgrade the desktop edition:sudo do-release-upgrade. One more info: I have kde installed.

  Read the article

• Allow user to SUDO a script without password.

  - by John Isaacks

  I have a php script with this: <?php #echo exec('whoami'); $output = shell_exec('bash /usr/local/svn/bash_repo/make-live'); echo "$output"; ?> The make-live script contains this: #!/bin/bash cd /var/www-cake sudo svn checkout file:///usr/local/svn/bash_repo/repo/ echo "Head revision has been pushed to live server" So the PHP user who is www-data needs to have nopasswd for that script. I am told I need to add: www-data ALL=NOPASSWD: /usr/local/svn/bash_repo/make-live To sudoers to allow this. First I run sudo visudo but I have no experience with vi so I try to open it in gedit with export EDITOR=gedit && sudo -E visudo which then just opens a sudoers.tmp file which is empty. I add the line and save it. But it doesn't do save. So I just try sudo visudo and I add the line right beneath this part: # User privilege specification root ALL=(ALL) ALL www-data ALL=NOPASSWD: /usr/local/svn/bash_repo/make-live I closed out sudoers and reopened to verify that it has saved. I even restart apache. I run the php file and it still doesn't work. What am I missing?

  Read the article

• Is it possible to execute keyboard input programmatically in Linux?

  - by Taylor Hawkes

  For example is there a Linux command or way that I could from a program (c++ | python| or other) enter a series of keyboard inputs that are interpreted as though they are keyboard inputs. I have a bad case of Repetitive Stress Injury (RSI) from typing. To ease my pain I developed a voice controlled interface using pocket sphinx and a custom grammar and to run a number of very common commands. ex: "open chrome" , "open vim". Basically what is shown here, but with slightly diff tools: http://bloc.eurion.net/archives/2008/writing-a-command-and-control-application-with-voice-recognition/ I have run into some limitation as I can only execute command line commands given a voice command. Rather than having a "voice command" - "command line command" mapping, I would like to have "voice command" - "keyboard input" mapping. So when my active window is a browser and I type + n, and new tab opens. If I'm in vim and new vim tab opens. Any suggestions, ideas, tools or approaches to this problem would be much appreciated. I understand the answer may not be simple, but would like to develop it none the less.

  Read the article

• Mac OS needs Windows Live Writer &ndash; badly!

  - by digitaldias

  I recently bought a new  Macbook Pro (the 13” one) to dive into a new world of programming challenges as well as to get a more powerful netbook than my Packard Bell Dot which I’ve been using since last year. I’ve had immense pleasure using the netbook format and their small size in meetings (taking notes with XMind), surfing “anywhere”, and, of course blogging with windows live writer. So far the Mac is holding up, it’s sleek, responsive, and I’ve even begun looking at coding in Objective C with it, but in one arena, it is severely lacking: Blogging software. There is nothing that even comes close to Live Writer for getting your blog posts out. The few blogger applications that do exist on mac both look and feel medieval in comparison, AND some even cost money! It looks like some mac users actually install a virtual machine on their mac to run Windows XP just so they can use WLW. I’m not that extreme; instead, I’m hoping that the WLW team will write it’s awesome application as a Silverlight 4 app. That way, it would run on Mac and Windows (as a desktop app). I wonder if it will ever happen though…   PS: The image is of me, took it with the built-in camera on the mac and emailed it to the windows PC that I am writing on :)

  Read the article

• Failing to upgrade to linux-image-3.0.0-26-generic

  - by Dan Lee

  When I try to upgrade linux-image-3.0.0-26-generic I get following problems: dpkg-deb (subprocess): data: internal bzip2 read error: 'DATA_ERROR' dpkg-deb: error: subprocess <decompress> returned error exit status 2 dpkg: error processing /var/cache/apt/archives/linux-image-3.0.0-26-generic_3.0.0-26.42_amd64.deb (--unpack): short read on buffer copy for backend dpkg-deb during `./lib/modules/3.0.0-26-generic/kernel/drivers/scsi/fnic/fnic.ko' No apport report written because MaxReports is reached already Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.0.0-26-generic /boot/vmlinuz-3.0.0-26-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.0.0-26-generic /boot/vmlinuz-3.0.0-26-generic Errors were encountered while processing: /var/cache/apt/archives/linux-image-3.0.0-26-generic_3.0.0-26.42_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: dpkg: dependency problems prevent configuration of linux-image-generic: linux-image-generic depends on linux-image-3.0.0-26-generic; however: Package linux-image-3.0.0-26-generic is not installed. I don't know why this happens to me; earlier upgrades always worked without problems. Does anybody know how to fix this?

  Read the article

• How do I work around sudo 'segmentation fault' on basic bash commands?

  - by sage

  I am sure the answers are out there, but alas there are too many answers (here and elsewhere) to other questions stopping me from finding them. I just encountered something substantially similar to what is described at the closed SO question, sudo : “segmentation fault” Ubuntu maverick [closed]. My team is using Ubuntu 11.04 on VMWare Workstation 8.0.4. We are doing development using c++, Xenomai, Qt, and Qt Creator. When we simulate our application on the virtual machine, we currently need to launch Qt Creator with sudo. My colleague mentioned today that he has been having issues where his workstation locks up and he needs to restart and that occasionally he has the issue that all sudo bash commands return "segmentation fault". I just ran our application in simulation mode. I was running Qt Creator under sudo and Qt Creator received the signal abort (if I recall). Afterward, every command executed with sudo from sudo qtcreator to sudo ls resulted in the message Segmentation fault. I clicked on the power widget to see if I could log out, but the system shut down straightaway without prompting. My understanding is that we run sudo because of a permissions issue with Xenomai and the VM as currently configured, but my colleague has a workaround for this. I expect that not running Qt Creator under sudo -- something that has always made me nervous -- will help contain this issue, but I find it troubling that this could happen and manifest as it does. Does anyone know what is happening? Any recommendations on how to work around this issue? This is happening often to I am trying tolobby for VM changes to be able to run the process without sudo.

  Read the article

• Formatting php, what works more efficiently?

  - by JamesM-SiteGen

  Hello fellow programmers, I was just wondering what makes php work faster, I have a few methods that I always go and do, but that only improves the way I can read it, but how about the interpreter? Should I include the curly braces when there is only one statement to run? if(...){ echo "test"; } # Or.. if(...) echo "test"; === Which should be used? I have also found http://beta.phpformatter.com/ and I find the following settings to be good, but are they? Indentation: Indentation style: {K&R (One true brace style)} Indent with: {Tabs} Starting indentation: [1] Indentation: [1] Common: [x] Remove all comments [x] Remove empty lines [x] Align assignments statements nicely [ ] Put a comment with the condition after if, while, for, foreach, declare and catch statements Improvement: [x] Remove lines with just a semicolon (;) [x] Make normal comments (//) from perl comments (#) [x] Make long opening tag (<?php) from short one (<?) Brackets: [x] Space inside brackets- ( ) [x] Space inside empty brackets- ( ) [x] Space inside block brackets- [ ] [x] Space inside empty block brackets- [ ] Tiny var names: often I go through my code and change $var1 to $a, $var2 to $b and so on. I do include comments at the start of the file to show to me what each letter(s) mean.. Final note: So am I doing the right thing with the curly braces and the settings? Are there any great tips that help it run faster?

  Read the article

• A question about the cobbler-ubuntu-import bash script

  - by user183394

  I have been testing the latest cobbler for PXE booting Ubuntu 12.04.1-server-x86_64 and 12.10-server-x86_64 using a Scentific Linux 6.3 host to run the cobbler server. With the former, I got everything going. But with the later, I haven't been successful. As an attempt to figure things out, I downloaded Ubuntu's cobbler 2.2.2 source package. Examining the content, I soon noticed that Ubuntu's cobbler 2.2.2 came with a cobbler-ubuntu-import bash script. I reviewed the code and spotted something interesting: line 9 of the script states: 9 AUTO_KOPTS='log_host=@@server@@ log_port=514 priority=critical locale=en_US netcfg/choose_interface=auto' But after extensive googling, reading both Debian and Ubuntu's documentation about the debian-installer, I don't see these two kopts log_host and log_port documented anywhere. Putting it in the profile of my current test setup, even my cobbler server host does run rsyslogd, I don't see anything logged either. No, I don't have iptables and selinux on on the cobbler server host. Can anyone point to me where I can read more about these two options? Having the ability to log an installation to a remote central logging host would be really cool.

  Read the article

• Visual Studio 2010 on Macbook Air

  - by Kyle B.

  Does anyone here run Visual Studio 2010 (or VS12 RC) on a Macbook Air? I have the current model with 4GB ram, 13" screen, and 256GB SSD drive. Before I go through the effort of configuring this, I'd like to know if anyone from the community has done this and: Was the performance acceptable? If it is, I plan to get a larger cinema display monitor as a second display and do all my coding on this machine ditching my desktop. Did you use Boot camp, Parallels, or VMWare? I feel to maximize performance that boot camp would be necessary to make the most utilization of the memory, but am not sure if this completely necessary. I'd prefer to use a VM, but wasn't sure if this was practical and would value your input before buying a license. Did you also run anything else on the Windows installation, such as SQL Server express, IISExpress, etc? Did performance lag after a certain point? Note: I would have asked this in superuser.com, but felt this applied more directly to the programming community.

  Read the article

• Squid 3 and Internet Explorer 11 with authentication

  - by StBlade

  Need some help. My college has up until now been running Squid 3 on Ubuntu 12.02 and now 14.04 successfully. That was till recently. Our WSUS server is dishing out updates to all our workstations of which Internet Explorer 11 is one of them. Now all of a sudden users do not need to authenticate via the squid proxy to be able to use the internet. This makes it rather difficult as I also use SARG to generate usage logs for all users each day. All our workstations also have Chrome on them, and Chrome authenticates fine via the Squid proxy. Doing a couple of Googles, I ran into and article, where someone made mention that Microsoft has deprecated digest and basic authentication from IE 11. Reason was given that Office 2013 was giving problems as it was not giving the popup screen for authentication when Office tries to download templates from the internet. I have run into this problem, but by setting those sites to not authenticate via squid fixed the problem. Has anyone else run into something similiar? Would changing to NTLM or Kereberos be a solution?

  Read the article

• Is HTML5/WebGL performance unreliable on low-end Android tablets and phones?

  - by Boris van Schooten

  I've developed a couple of WebGL games, and am trying them out on Android. I found that they run very slowly on my tablet, however. For example, a game with 10 sprites or so runs as 5fps. I tried Chrome and CocoonJS, but they are comparably slow. I also tried other games, and even games with only 5 or so moving sprites are this slow. This seems inconsistent with reports from others, such as this benchmark. Typically, when people talk about HTML5 game performance, they mention well-known and higher-end phones and tables. While my 7" tablet is cheap (I believe it's a relabeled Allwinner tablet, apparently with the Mali 400 GPU), I found it generally has a good gaming performance. All the games I tried run smoothly. I also developed an OpenGL ES 2 demo with 200 shaded 3D objects, and it ran at 50fps. My suspicion is that many low-end and white-label devices may have unacceptable HTML5/WebGL support, which means there may be a large section of gamers you will not reach when you choose this as your platform. I've heard rumors about inconsistent performance of HTML5 and WebGL on different devices, but no clear picture emerges. I would like to hear if any of you have had similar experiences with HTML5 or WebGL, or whether I can find information about the percentage of devices I can expect to have decent performance.

  Read the article

< Previous Page | 335 336 337 338 339 340 341 342 343 344 345 346  | Next Page >