Search Results

Search found 10207 results on 409 pages for 'ethernet switch'.

Page 34/409 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

  • Unable to set initcwnd on a Hetzner server

    - by Sergi
    We just ordered a bunch of Hetzner EX40SSD servers with the minimal Debian install image that they provide and everything is just fine except that looking at tcpdumps for fine tuning the network from various locations the initcwnd param seems to be stuck at 6 no matter how we change it. By default Debian 3.2 kernels should have that setting to 10 so it's pretty strange. Is it possible that the NIC driver or a custom setting in the Hetzner Debian image is limiting this param? Even if we set it to 4, like the old kernel default, it doesn't work. Any ideas would be much appreciated! Does anyone know if the NIC drivers provided by default by Debian have some kind on limitation. In a long thread in http://www.webhostingtalk.com/showthread.php?t=1200617&highlight=hetzner they talk about a page http://wiki.hetzner.de/index.php/Installation_des_r8168-Treibers/en where Hetzner states that the included Realtek r8168 driver is not working properly, but nowhere do they say that the initcwnd could be affected. Tomorrow i will try to install a CentOs image and see if Debian is the problem...Last resort would be to install a custom debian image, but that is a pain in the ass! Thanks!

    Read the article

  • How can I detect if a NIC is UP in UNIX?

    - by Rich
    I am currently writing a bash script (for Nagios), and I would like to be able to detect if specific network cards are up or not. My best guess is to do something like this: ifconfig eth0 | grep UP | wc -l or: ethtool eth0 | grep "Link detected: yes" | wc -l Are either/both of those reliable ways of testing if the network card is up, or is there a better option? Perhaps there is a flag on ethtool which will do precisely what I want? Thanks in advance for any suggestions/pointers! Rich

    Read the article

  • What happens when ARP Request comes from a different subnet?

    - by gsinha
    What will happen when an ARP Request packet is sent from router1 to router2 in the following two cases? Will an ARP Reply be generated or the ARP Request packet be dropped? [router1]Intf1(20.0.0.1/24) ======== (40.0.0.1/24)Intf2[router2] [router1]Intf1(20.0.0.1/24) ======== (20.0.0.2/8) Intf2[router2] The topology above have a port "Intf1" on router "router1" connected a port "Intf2" on another router "router2" via a direct link(eg, a 1 Gbps cable).

    Read the article

  • Set 802.1Q tagged port on VLAN1 on Dell PowerConnect switch

    - by Javier
    I'm having big troubles when adding this Dell switch to my network. Here we use several VLANs to segment traffic. All switches (3com and DLink mostly) have configured the same VLANs, most ports are 'untagged' and belong to a single VLAN, except for the ports used to join together the switches (in a star topology), these ports belong to all VLANs and use 802.1Q tags. So far, it works really well. But on this new switch (a Dell PowerConnect 5448), the settings are very different (and confusing). I have configured the same VLANs, an the uplink ports are set in 'general' mode (supposed to be fully 802.1Q compliant), I can set the VLAN membership as 'T' on these ports for all VLANs except VLAN 1. It always stay as 'U' on VLAN 1. Any ideas?

    Read the article

  • Network router and switch configuration

    - by gilly3
    Can I put a switch before my router in my home network? Here is a diagram of how I want to set up my network: ________________________________ ________________________________________ | | | | | Cable Access Panel | | Home Office | | _____________ ________ | | _____________ | | | | | | | | | | _________ | | | Cable Modem |--->| Switch |-------------->| Router |____| | | | |_____________| |________| | | |_____________| | Printer | | |______________________/____\____| | / | \ |_________| | ___/_ _\___ | _____/ ____|____ \_____ | | | | | | | | | | | | | | PC1 | | PC2 | | | PC3 | | Ext. HD | | PC4 | | |_____| |_____| | |_____| |_________| |_____| | |________________________________________| The reason I want to do this is because my router is also my wireless access point. My cable modem is located in the far corner of my home where my phone/tv/network access panel is. I'd rather keep the wireless access point in a more central location, but I'm not sure if DHCP will continue to work properly with that configuration. Edit: I'd like to continue to be able to share files and access my networked drive and printer from each computer in the house.

    Read the article

  • USB Device With Embedded Fileserver

    - by Richard Martinez
    I'm attempting to access logs from a proprietary hardware box with no reasonable hope of modifying the software. There is a process on the device to dump log files to a flash drive on the USB port after entering a code sequence. Currently, analysis of the logs requires the following: Physical presence at the device Manual entry of the code sequence Removal of USB device Insertion of USB device into a normal Linux box I'm hoping there is some sort of device that can act as a USB mass storage device but simultaneously make it's contents available as a network file share (wired preferred). Does such a device currently exist? A combo hardware/software solution would also work.

    Read the article

  • Does using VLANs in your network infrastructure cause an appreciable decrease in performance?

    - by Peter Grace
    This is something I've never considered before and wanted the opinions of the experts. We use VLANs day in and day out for various network tasks. My modus operandi is that in general, if something supports VLANs, that port is getting trunked because it just makes a ton of sense if there's even the slightest chance you need to do more than one thing on that single link. As I ponder this, though, I'm wondering whether there's a performance penalty involved with this line of thinking? Is the impact negligible?

    Read the article

  • Multiple IPs from one router

    - by ergoen
    I would like to know if it is possible (and if so, how) to configure a router running dd-wrt (or openwrt) to supply connected devices with two ip addresses. The network looks like this: [Internet] | [Router] | | [Comp1] [Comp2] ... My ISP provides me with enough public IP adresses to give all devices on my network one each. The easiest way to set that up is to just use the router as a switch. This will however lead to problems with some LAN based applications. I would still like to use Samba-shares between the computers as well as a vpn server. What I am looking for basically is if it is possible to use the router as a DHCP server for a local network (let's say giving IP adresses 192.168.1.xx to connected computers) while at the same time passing through public IP addresses to each as well?

    Read the article

  • Why does no small Rj45 port exist?

    - by Christian Sauer
    While I bought my last Tablet I noticed that no Tablet (and most smaller notebooks /convertibles) has a Rj45 port. Which I finde quite dissatisfying since I like to use RJ45 in numerous places. I think a reason could be that Rj45 is simply too big for a Tablet - it is downright massive compared to micro USB /HDMI etc. But that leads me to my question: Why is there no attempt to build a smaller micro-Rj45 port which could be used in constrained spaces?

    Read the article

  • How to make sure you server NIC performance is at best on Windows?

    - by Bobb
    I realised that I followed some obscure paper on setting NICs on Windows for too long. It might be outdated with new hardware released in past couple of years and with W2008R2. I read a bit about offloading and RSS settings on Windows and I realiased that it is very much circumstantial. Noone can really say - enable that and disable this. etc. So what I really want is for my next server try and setup testing environment and measure how my particular application will behave with different settings. The target is going to be latency of TCP primarily. Please note I am talking about latency inside the box. Are there precision tools for Windows to measure latency (down to microseconds)? P.S. I know this is not easy question. Windows time drift is awful problem for any precision test but still I am sure I am not the fist person to need that... Please share your experience

    Read the article

  • How to reply some request from which routes its came from?

    - by tacoen
    I wonder if we can reply some request from which route its came from? My Situation is like this: eth0 192.168.10.1 --> gw: 192.168.10.254 nm: 24 eth1 192.168.11.1 --> gw: 192.168.11.254 nm: 24 Since this two IP is on the same machine, normally when we ping to 192.168.11.1 from 192.168.10.2. This machine will not reply to 192.168.10.2 because 192.168.10.0/24 it's on eth0, and the packets where requested via eth1. Can I make it works? I'm using Linux ubuntu, and the application will be listen to eth1 only.

    Read the article

  • How to change the setting for a network device reported by ethtool, specifically Speed, on VM?

    - by Ramadheer Singh
    This is related to these two questions, although they don't answer my question. The machines are RHEL6. 1.ethtool not showing all the properties 2.changing network speed to 1000Mb/s Output on VM: [root@foo ~]# ethtool eth0 Settings for eth0: Current message level: 0x00000007 (7) Link detected: yes Output on Real Hardware: (interested in Speed) # ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes ***Speed: 1000Mb/s*** Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: d Wake-on: d Link detected: yes if there's anyway I can set this in VM, please suggest.

    Read the article

  • arp across subnets which devices can be detected?

    - by Gobliins
    i have some devices connected in the same physical network (LAN) but in different subnets. I want to detect them all with the ARP from my computer. My Computer is also in the same physical network but on a different subnet. ! The devices have no arp protocol installed (yet). Is it possible to detect the devices (with or withour ARP installed on every device)? If the devices have a MAC-address but no IP-address, can ARP still detect the machines?

    Read the article

  • How to setup an Openvpn server with two gateways to internet

    - by fourat
    I have an openvpn server behind two wan interfaces: eth1 and eth2 where eth1 is the default gw and eth2 is where openvpn binds to. The problems my ovpn server is replying back to ovpn client via the default gw (through eth1) and the tcp negociation is lost before establishing any tunnel. Here's what's happening: wan client -----> eth2 ----> openvpn -----> eth1 ----> lost and not delivered back to client Is there a way to tell ovpn to stick on eth2 and consider it for all traffic ?

    Read the article

  • Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

    - by user94217
    I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

    Read the article

  • Triple head DVI KVM

    - by cat pants
    I am trying to run a Linux desktop and Windows desktop simultaneously with a KVM for maximum productivity. Also running three monitors. I need a KVM that can do 3x DVI @ 1920x1080 + 2x usb (mouse and keyboard) + toslink for two machines. What would you suggest? I ask on here because I have searched quite a bit and have yet to find a KVM with these requirements. (I would be open to something like modifying 3x regular KVMs to control them with one button or similar) Thanks! (I tried posting this question earlier, but it was closed as being "not related to computer hardware or software" ... is a KVM not related to computer hardware or software? I'm pretty sure it is. kvm-switch has been tagged 100 times on here for example.)

    Read the article

  • How to switch users without entering password, part II

    - by torbengb
    I've got Ubuntu 9.10 with a user account for my wife, and one for myself. "Wake-from-screensaver" should result in "choose user" without having to enter any password. I know how to do that in Windows, but I'm not good with Linux (yet). Part of this was answered in this question which helped me get past the login screen without passwords (after booting, and after choosing "switch user"), but once the screensaver kicks in and I wake it up again, the system does not present the "choose user" screen. Instead, it either turns off the screensaver and presents the desktop of the most recent user, or (if the screensaver is set to lock the screen) prompt for the user's password (which can be handily surpassed by clicking the "switch user" button and choosing the same user again). So, the login ("choose user") screen has been dealt with. How do I make the (any) screensaver return to the login screen at wake, rather than to the current user's desktop? Windows can do this, I'm sure Linux can too - but how?

    Read the article

  • Gigabit connection between 2 computers

    - by Alecu
    I am trying to set up a connection between 2 pc's. It's a direct cable connection. The problem that I am having is that the connection isn't gigabit. I know both network cards support gigabit. I checked in the device settings and in one pc I can see in the Speed & Duplex the 1Gbps option but on the other pc I can't see that option despite the fact that the network card is gigabit. I have quite some files to copy from one pc onto another and I really need a good connection between them. I can't really remove the hard drive because it would void the warranty. Could this be a driver issue or a cable issue? On both pc's I have windows 8. The network card on the pc that doesn't have the 1 gbps option is an Atheros ar8161 card.

    Read the article

  • 2 RJ45 connectors on a one WAN cable

    - by mr_stavo
    Hello, I encountered strange setup on a network at company where I do some work. They have internet connection from small ISP located in the same building, all I see is one CAT5 cable with 2 RJ45 connectors. One is going to WAN port on the router and another into LAN port on the same router. This is the only way for internet connection to work. I tried to connect my laptop to one of the RJ45 but it won't work. Now, what is the purpose for such setup?

    Read the article

  • Hotkey to switch between windows in taskbar order in Windows 7

    - by TheQuickBrownFox
    Is there a hotkey to cycle through open windows in the order that they appear on the taskbar. This should switch windows without additional keypresses. I know of win+T. This shortcut puts focus on the first taskbar icon and allows you to select and display a window with up/down/enter. I would ideally like something like Ctrl+Win+Down to immediately switch to the next window. If not, then is there any way to enable this behaviour on a completely locked down PC where I cannot install software, run executables or edit the registry?

    Read the article

  • Android 2.1 switch loop JRE 1.7

    - by Defuzer
    Hello how to use switch loop in my android project ? I want to use Android 2.1 I need JRE 1.7, but I want to use Android 2.1 I use loop like this: switch ((CHAR[Math.abs(intGen.nextInt()%2)])) { case "+": result = random2 + random3; break; case "-": result = random2 + random3; break; } LogCat: Cannot switch on a value of type String for source level below 1.7. Only convertible int values or enum variables are permitted

    Read the article

  • switch vs. if...else if...else

    - by John Hartsock
    Guys I have a couple of questions: Is there a preformance difference in Javascript between a switch statement and an if...else if....else? If so why? Is the behavior of switch and if...else if...else different across browsers? (FireFox, IE, Chrome, Opera, Safari) The reason for asking this question is it seems that I get better preformance on a switch statement with approx 100 cases in Firefox. But in IE it get better preformance with 100 if...else if...else.

    Read the article

  • Utility to grant admin rights to a user in Windows XP for few hours/days?

    - by user15660
    Hi, I have two accounts on my windows xp home desktop. The default regular user is used for everything and the 2nd user which has admin rights is used only for installations. I do this to avoid malware infestations during web browsing and limited user account is guarding against online threats to a good extend but many programs refuse to run under limited rights like revo uninstaller. many installs i run from limited user by selectin "run as" from right click context menu of the .exe file. but some apps need admin rights for certain. I use "switch user" to go to admin mode and do the install/uninstall. but the admin user has none of my preferences bookmarks setup nor has my locate32 indexing done and ready for fast search Is there a utility which I can use "run as" login in administration login and use that to grant my limited user admin rights for a limited amount of period like few hours or days? Please help. I guess MS might have closed many doors of it for fear of exploitation of the API. are there any?

    Read the article

  • Utility to grant admin rights to a user in Windows XP for few hours/days?

    - by user15660
    I have two accounts on my windows xp home desktop. The default regular user is used for everything and the 2nd user which has admin rights is used only for installations. I do this to avoid malware infestations during web browsing and limited user account is guarding against online threats to a good extend but many programs refuse to run under limited rights like revo uninstaller. many installs i run from limited user by selectin "run as" from right click context menu of the .exe file. but some apps need admin rights for certain. I use "switch user" to go to admin mode and do the install/uninstall. but the admin user has none of my preferences bookmarks setup nor has my locate32 indexing done and ready for fast search Is there a utility which I can use "run as" login in administration login and use that to grant my limited user admin rights for a limited amount of period like few hours or days? Please help. I guess MS might have closed many doors of it for fear of exploitation of the API. are there any?

    Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >