Search Results

Search found 962 results on 39 pages for 'laptops'.

Page 34/39 | < Previous Page | 30 31 32 33 34 35 36 37 38 39  | Next Page >

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• Connecting multiple access points

  - by mohsen farahanipoor

  I'm working on a big project. We want to create a wireless network throughout the building with 15 floors. My idea is that we should set up one unified wireless access point at least in each floor...in case of signal attenuate, we use Access point extender/repeater. I selected DWL-6600AP from among D-Link industrial access points. I want to implement a single wireless LAN throughout the building. Is it possible to combines multiple DWL-6600 access points to achieving just a single WLAN? Can a wireless switch controller do this task? Can these Access Points interfere with each other? What is the solution? I read D-Link website's learning materials, but I am still confused. My other question is around the connecting these APs to Wireless Switch Controller - Is it possible to use power line for connecting DWL-6600 to Wireless Switch Controller device? My main goal is that clients with portable devices such as laptops should be easily connected to the network to share & have communication without any more manual configuration as they are already connected to a single network.

  Read the article

• Synergy: Cannot send media keys from Linux to Mac

  - by CraftyThumber

  I have a Linux Synergy server (Si-Linux) serving just one Mac client (Macbook Pro UK) (SiBook-Pro.local). On my Linux server I am using a USB Apple keyboard with the exact layout of the laptops keyboard (the compact UK aluminium keyboard). I would like to send the media keys to the Mac client at all times and I have attempted the following in my synergy.conf: keystroke(AudioPlay) = keystroke(AudioPlay,SiBook-Pro.local) This did not seem to work so I ran both the server and client as foreground processes and with debugging enabled and observed the following: Server Log: DEBUG1: activate actions DEBUG1: hotkey: keyDown(AudioPlay,SiBook-Pro.local) DEBUG1: onKeyDown id=57523 mask=0x0000 button=0x0000 DEBUG1: send key down to "SiBook-Pro.local" id=57523, mask=0x0000, button=0x0000 DEBUG1: deactivate actions DEBUG1: hotkey: keyUp(AudioPlay,SiBook-Pro.local) DEBUG1: onKeyUp id=57523 mask=0x0000 button=0x0000 DEBUG1: send key up to "SiBook-Pro.local" id=57523, mask=0x0000, button=0x0000 Client Log: DEBUG1: recv key down id=0x0000e0b3, mask=0x0000, button=0x0000 DEBUG1: mapKey e0b3 (57523) with mask 0000, start state: 0000 DEBUG1: key e0b3 is not on keyboard DEBUG1: recv key up id=0x0000e0b3, mask=0x0000, button=0x0000 DEBUG1: recv enter, 1279,386 5 2000 As you can see, the client claims the key received is not on keyboard. I don't understand since it is the same key as is on the Macbook's keyboard. I tried to reverse the client-server config to see if I could capture the key being sent if I pressed the Play button on the Macbook but the key doesn't seem to even make it to Synergy. Almost all keyboard presses get logged but the media keys seem to bypass the logs and just execute their function locally. E.g. I press play on the Macbook (with the Macbook as the server) and the key plays music on the Macbook and the key is not logged to the debug log.

  Read the article

• Is there any way to limit the turbo boost speed / intensity on i7 lap?

  - by Anonymous

  I've just got a used i7 laptop, one of these overheating pavilions from HP with quad cores. And I really want to find a compromise between the temp and performance. If I use linpack, or some other heavy benchmark, the temp easily gets to 95+, and having a TJ of 100 Degrees, for a 2630QM model, it really gets me throttling, that no cooling pad or even an industrial fan could solve. I figured later that it is due to turbo boost, and if I set my power settings to use 99% of the CPU instead of 100%, and it seems to disable the turbo boost, so the temp gets better. But then again it loses quite a bit of performance. The regular clock is 2GHz, and in turbo boost it gets to 2.6Ghz, but I just wonder if I could limit it to around 2.3Ghz, that would be a real nice thing. Also there is another question I've hard time getting answer to. It seems to me that clocks are very quickly boosting up to max even when not needed, eg, it's ok if the CPU has 0% load, the clocks get to their 800MHz, but even if it gets to about 5% it quickly jumps to a max and even popping up turbo, which seems very strange to me. So I wonder if there is any way to adjust the sensitivity of the Speed Step feature. I believe it would be more logical to demand increased clock if it hits let's say 50% load. I do understand that most of these features are probably hardwired somewhere in the CPU itself or the MB, which has no tuning options just like on many laptops. But I would appreciate if you could recommend some thing, or some software. Thanks

  Read the article

• make pentaho report for ubuntu 11.04

  - by Hendri

  currently i'm trying to install Pentaho Reports for OpenERP which is refer from https://github.com/WillowIT/Pentaho-...rver/build.xml i ever installed on some laptops which is Windows Based and it's working, but currently i'm trying on UBuntu 11.04 OS, it prompted me error like this "error build.xml:18: failed to create task or type.." below is the steps i did : 1. install java-6-openjdk comment : "apt-get install java-6-openjdk" then i set installed java jdk into java_home environment command: "nano /etc/environment" add environment with this new line : JAVA_HOME="/usr/lib/jvm/java-6-openjdk" I install apache ant command : "apt-get install ant" followed by setting the evnironment command: "nano /etc/environment" add environment with this new line : ANT_HOME="/usr/share/ant" try to check installation with command "ant"... I get message like this: Buildfile: build.xml does not exist! Build failed then download java server from https://github.com/WillowIT/Pentaho-...rver/build.xml and then copied to Ubuntu share folder and then on command form, i goto extracted path which is share folder i mentioned and executed command "ant war " and i got error message : BUILD FAILED /share/java_server/build.xml:18: problem: failed to create task or type antlibrg:apacge.ivy.ant:retrieve cause: The name is undefined. Action:Check the spelling. Action:Check that any custom taks/types have been declared Action:Check that any /declarations have taken place. No types or taks have been defined in this namespace yet This appears to be an antlib declaration. Action:Check that the implementing library exists in one of: -/usr/share/ant/lib -/root/.ant/lib -a directory added on the command line with the -lib argument Total time:0 seconds is there any compability issue? or i miss out some steps? i'm in the some project to rush with for reporting, so please help me to solve this issue i look forward to your corporation to help me solve this issue, thanks a lot in advance Thx Best Regards,

  Read the article

• Setup windows 2012 AD in Hyper-V for a Test environment

  - by hub

  Im trying to setup a Windos 2012 R2 test environment on my work computer (a laptop). I have a AD, DHCP and DNS server on server A, and a client connecting to the doman and that works. The client can ping the AD server and gets a valid IP adress. If I ping google.com from the client I get the IP adress but I dont get any responses (request time out). If i ping google.com from server A it works as it should. Server A have a connection to the Internet through a "external network switch" in hyper-v, which gets its internet from a router and the client is connected to a "internal network switch". May the poblem be that server A is behind a router? Can I make this solution to work regadless the network my laptop is connected to? At home i have one IP adress, at work its a totally different range. What I would like is to use my laptops internet connection, regardless wifi or wired, to act as incomming internet, is this possible?

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Desktop Provisioning for a Small Linux Software Development Team

  - by deakblue

  Goal: Get a small team using a standard development image rather than 4 software devs setting up their own environments. Why: it takes a day or days to install a distro, build-specific libraries, tools like editors and IDEs, mysql, couchdb, java, maven, python, android-sdk, etc. It's a giant PITA that when repeated 4 times by 4 developers (not sys admins) wastes time and generates annoying divergences that crop up later (it-builds-on-my-box syndrome). There's no sharing of productivity, settings, tricks, scripts, set-ups. Some of this is helped by segregating the build systems into headless virtualbox images. This doesn't really address tooling though or the GUI-desktop dev that needs doing. So I see three basic strategies, ghosting, virtualization, and finally creating a kind of in-house linux distro (I guess Google does something like this). The target dev environment is based on Debian OpenBox and must allow a mix of 3rd gen Core i7 notebooks 8GB-minimum to work both single and multihead. Important, the lappies are not the same, but a mix of 2012 macbooks and PCs. So: virtualization: is doing all of your work within a VM, like VirtualBox, practical on this hardware or annoying. ghosting: will laptops from different manufacturers make this impractical. DIY distro: short of scripting a bunch of package installs, I don't know if there's any "distro-maker" that could keep this from being an epic project of scripting package installs. So any advice?

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• How can I automatically synchronize a directory tree on multiple machines?

  - by Blacklight Shining

  I have two Mac laptops and a Debian server, each with a directory that I would like to keep in sync between the three. The solution should meet the following criteria (in rough order of importance): It must not use any third-party service (e.g. Dropbox, SugarSync, Google whatever). This does not include installing additional software (as long as it's free). It must not require me to use specific directories or change my way of storing things. (Dropbox does this IIRC) It must work in all directions (changes made on /any/ machine should be pushed to the others) All data sent must be encrypted (I have ssh keypairs set up already) It must work even when not all machines are available (changes should be pushed to a machine when it comes back online) It must work even when the /directories/ on some machines are not available (they may be stored on disk images which will not always be mounted) This can be solved for Macs by using launchd to automatically launch and kill (or in some way change the behavior of) whatever daemon is used for syncing when the images are mounted and unmounted. It must be immediate (using an event-based system, not a periodic one like cron) It must be flexible (if more machines are added, I should be able to incorporate them easily) I also have some preferences that I would like to be fulfilled, but do not have to be: It should notify me somehow if there are conflicts or other errors. It should recognize symbolic and hard links and create corresponding ones. It should allow me to create a list of exceptions (subdirectories which will not be synced at all). It should not require me to set up port forwarding or otherwise reconfigure a network. This can be solved by using an ssh tunnel with reverse port forwarding. If you have a solution that meets some, but not all of the criteria, please contribute it in the comments as it might be useful in some way, and it might be possible to meet some of the criteria separately. What I tried, and why it didn't work: rsync and lsyncd do not support bidirectional synchronization csync2 is designed for server clusters and does not appear to work with machines with dynamic IPs DRBD (suggested by amotzg) involves installing a kernel module and does not appear to work on systems running OS X

  Read the article

• Wireless signal changes from strong to weak after connecting

  - by gibberish

  Router (primary AP) is a WRVS4400N, WAP (signal booster) is a WAP4410N. Problem: User is physically located within ten feet of WAP (200 feet from main wireless router). Signal is at 5 bars as user connects to wireless network. Within seconds, signal is at or below two bars and connection is poor. Background: Trying to solve problem of weak wireless signal in back offices. Desired result is for client laptops to automatically switch to the stronger signal. WAP is connected to network via Ethernet cable. WAP is set to AP mode (instead of Wireless Repeater mode) WAP does appear to boost signal. Using Windows 7 sys tray Connect To A Network applet, can observe signal boost as laptop approaches the WAP. Above-described problem happens to users located near or beyond the WAP. It does not happen to users in close proximity to the router. Secondary Question: If using WAP in AP Mode, do WAP and Router (primary AP) need to be on the same channel?

  Read the article

• Wifi Works with Android and Windows 8 but not Linux and Win 7

  - by eramm

  Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

  Read the article

• Home Network Stopped Working

  - by James

  I have a home network where a machine running Windows 7 Ultimate N acts as a central hub for other devices to access media. This has been running for around 2 years now and there has been no recent configuration changes. The machine has a static IP address (192.168.0.3), which also has not been changed. A few laptops, Sonos music system and mobiles are using the machine for music/video mostly. Additionally, post 3389 was also open for RDP. I used a no-ip agent to map a hostname so I could RDP to the machine from the internet. As of yesterday when I try to ping the machine, I get PING:Transmit Failed, General Error I noticed however, the IP it is pinging is 0.0.2.233. All shares etc are no longer functioning including RDP. On the machine itself, an IP config shows like nothing has changed. It still shows the expected IP. If I ping itself from its hostname, I get the same error as above. machine has been rebooted, the router has been also. Any ideas where to even start on this?

  Read the article

• Matching up HomeGroup users created in different versions of Windows

  - by pdr

  In our household, we have 2 laptops and a desktop, all currently on Windows 8.1. The desktop has been upgraded in stages from Windows 7. Laptop 1 was bought with Windows 8 and has now been upgraded. Laptop 2 is new and came with Windows 8.1. We've been trying to set up a HomeGroup such that we have one user on laptop 1, one on laptop 2 and both can log into the desktop, with each user able to edit their files on their laptop and desktop, while the other user has read-only access. And we now have that situation ... except ... because the user on laptop 1 was created in Windows 8 but the same user on the desktop was created in 8.1, they have different names in Windows Explorer (say, firstuser and first_000). Likewise, the other use was created on laptop 2 in Windows 8.1 and on the desktop in Windows 7 (so let's say secon_000 and seconduser). This is ultimately confusing. Now if we expand the HomeGroup, we get four users (firstuser, first_000, seconduser and secon_000) and each has a single computer inside it. What I'd like to see is firstuser = laptop1, desktop and seconduser = laptop2, desktop. An acceptable alternative is first_000 = laptop1, desktop and secon_000 = laptop2, desktop. But what I don't want to have to do is delete firstuser and seconduser and rebuild them. Is there a better way?

  Read the article

• Linux file server for an inexperienced admin

  - by Pat

  A charity I volunteer for wants a file server for their mostly Windows machines (about five XP and 7 machines, with some Mac laptops every now and then). For the server, I have a PC with an Intel Core 2 Duo 3GHz proc, 4GB of DDR2 400MHz RAM, and a 500 GB HDD. (I should point out that they do not currently have any server - they are just using Windows to share a folder on one of the PCs.) What is a linux distro that is easy to configure for Windows file serving yet stable and secure enough to protect sensitive data without an expert sysadmin? I'm guessing that a Debian distro would probably fit the security bill, but I don't know of any tailored to novice sysadmins. Also, are there any killer apps for making this easy to administer and set up (as a Windows file server, in particular - this answer is a good example)? Would FreeNAS be sufficient? Once it's all set up, what are the minimum measures I need to take to keep the data secure? I found this somewhat helpful answer, but it's not specific to my question of just getting a secure file server up, running, and maintained.

  Read the article

• What to do with old laptop screens?

  - by Lord Torgamus

  This question is inspired by another SU question I came across earlier today: What to do with old hard drives? It made me think about two long-dead laptops I have with perfectly good screens still inside. One is a Dell Inspiron 5100 and the other is an Averatec E1200, but responses need not be geared towards those particular models' screens. Rules, based heavily on the original question's: Objectives and suggestions to keep in mind when you post an answer : Should showcase your geekiness, be plain ol' fun, serve a social purpose or benefit the community. Your answer need not be limited to only one screen. For a really good answer, I'll go out and buy additional leftover screens. Your answer need not be limited to one project per screen. If additional accessories need be purchased, make sure they are common. Don't tell me to get a moon rock or something. The projects you suggested should serve a useful purpose; art is nice, but functional art is way better. Thanks in advance, folks. EDIT: Found another related question. Fun projects to do with an old 17" LCD monitor EDIT 2: I, for one, am enjoying the new outpouring of creativity here. Best fifty bucks... I mean, rep points... I ever spent. EDIT 3: That does it. At the end of the week, there was a tie for most votes between the accepted answer and the game platform answer. The game platform answer was cooler, but less reasonable as a project to actually do; in other words, it was more moon rocky. Unfortunately, I think fencepost had the best comment on the topic, which is that displays on their own have no good interface. Thanks for playing, everyone!

  Read the article

• SBS 2008 - DNS Forwarders timing out.

  - by Moif Murphy

  Hello, We have an SBS 2008 server that keeps losing connection to the internet approx 2-3 times a day. It's a simple setup, BT Business Broadband ADSL to a Wireless Zyxel router to the server. Clients connect via WiFi from their laptops. Plugging ethernet in makes no difference, only a reboot of the router seems to bring everything back again. I'm looking at the forwarders on the DNS properties page and they're timing out when trying to resolve the IPs. Currently there are two IPs in there, 194.72.9.34 which has timed out and 194.72.9.38 which has finally resolved to ns8.bt.net We've been in there and replaced all media, installed a PCI NIC, have changed the router three times. There are no errors in the DNS event logs pertaining to what's going on. We've also been on to BT who are adamant that it's not their end. Could someone shed some light on what could be going on or where else to look in the configuration of the server? Thank you.

  Read the article

• Configuring two nearby WLANs: should I use the same ssid?

  - by Rory

  I'm configuring a home network for basic internet use (ie don't really need connectivity between workstations on the network). My brick walls mean a single wireless router doesn't provide good coverage throughout the house, so I have purchased two powerline adapters and now have the incoming modem/wireless router at one end of the house plugged into a powerline adapter, and at the other end of the house the other powerline adapter plugged into another wireless router. Currently the two wireless networks have different ssids. (The powerline adapters only do power-Ethernet; they're not wireless access points themselves.) This works well, except when I move between rooms and would ideally like my devices (iPad, phones, laptops) to switch from the weak to the strong signal. Sometimes there's enough signal that they hold on to the weak connects instead of switching to the strong one. Should I name the two networks the same ssid, and if so what is the actual effect? Do the signals get confused, is the bandwidth affected, will this help my devices seamlessly move from one to the other, or is the ssid just a cosmetic thing that actually doesn't have any impact on this situation? Are there any other settings that I should configure to make my setup optimal?

  Read the article

• wireless to wired internet

  - by Mark T

  My wife uses an old computer which doesn't really like having an internet connection via a USB wireless adapter. I've tried several, and none have been satisfactory. The connection gets dropped often and it is frustrating for her. A wireless card also had the same trouble. Repositioning the computer made no difference. (Two laptops, nearby, connect just fine and stay up, so it isn't the router.) However, the computer always worked well when I had an Ethernet cable connected to it. I know there is a box which will connect to my wireless network and provide an Ethernet cable connection. But the terminology used is so complex, I can't tell what it is I really need. In case that wasn't clear, here it is in different words: What I need is just the opposite of a wireless router. My wireless router takes my cable modem's Ethernet connection and makes it available to wireless clients. What I want is a box which is a wireless client to my wireless router and provides an Ethernet cable connection that I can connect to any device. I need to know the right name for a box with such capabilities. If you know of some inexpensive examples, that would also be helpful. I'm running a wireless G network with a Linksys Router.

  Read the article

• Something like Dropbox for local use

  - by Casper

  I am looking for a solution to sync folder pairs between a NAS and multiple local macs. Each of the macs could edit files and the other macs should then get synced automatically. Basically my own local version of Dropbox without using "cloud-storage". I have looked into solutions using rsync. As I understand it rsync is not really capable of doing a bi-directional sync. I also do not want to necessarily invoke the sync process. I would prefer a daemon running in the background - waiting and checking for changes and then syncing them "live". The program should also be flexible enough to recognize that it sometimes (in the case with laptops) can not reach the NAS. It should then just wait for the connection to be back again, without bugging me ever few minutes. I have looked into synk, folderwatch, rsync and a few others, but I haven't really found a solution. Isn't there something like "offline folders" from microsoft for the mac? Thanks PS: just for clarification - I don't want to sync for backup purposes, instead I am wanting to sync so that all macs have a local copy of the most recent changes to files.

  Read the article

• What does the 'Burst Rate' stat mean in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks

  Read the article

• Linksys SFE2000 Interface

  - by boburob

  I have a real problem with a layer 3 Linksys switch. First, every time it looses power, it seems to reset back to an older config. Not only this, but when this happens it looses interface settings on one subnet. This would not be a problem but I am completely unable to get to the interface on the working side. It allows me to log on and then just displays a blank screen. I have tried this on: IE6 IE7 IE8 IE9 Firefox 3.5 Opera Chrome All with the same results, except for Opera, which loads half the interface but nothing I can really use. I really need to get onto this switch so I can sort out routing and VLAN tagged ports, so if anyone has any ideas on either of these issues please let me know ASAP! Thanks! Also, due to its location and my lack of laptops with serial connections I cannot putty into it. UPDATE: Looked into this a bit more and it looks like this model of switch does not save the current config to boot unless you make sure to save it yourself, which explains the first issue, however the broken interface is more worrying!

  Read the article

• Setting up a home network

  - by Mat Richardson

  I'm trying to get my head around how to do this with the equipment I have. Here's how it is.. I have an old laptop that has server 2003 installed on it. This has no wireless NIC, but I have a spare wireless router that I can wire to it. We have a virgin wireless router which provides the home with internet access. What I would like to do it make resources on the server 2003 machine available to the rest of the devices in the home - specifically a couple of laptops running windows 7. Ideally I'd like to be able to use the laptop as a fileserver but maybe also offer application virtualization. In the first instance however, I'd like to create a file server with the laptop and allow connections to it by the other machines. Virtualisation is just a 'nice to have'... Given the hardware I have is this possible? Can you point me in the right direction how to do what I want if this is the case?

  Read the article

• Network bandwidth usage dashboard?

  - by SkippyFlipjack

  I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

  Read the article

• Advice on cloning disk

  - by hks

  I'm going to buy a second disk for backup, the same size as my laptops. I want to mount it in a casing via usb and backup an entire hdd every soemtime. That's because I want the posibility to just switch drives in case of something goes wrong. I'm using Linux and obviously the right tool seems to be dd. The thing is that my laptop drive has a speed of around 50-70 MB/s and usb 2.0 is 57 MB/s. So to copy my 250GB disk should take me more than 1 hour if I'm lucky. I can't wait this much. I want some differential backup. I read one of JWZ articles. In it he gives more details for using rsync on Mac. He writes that there is possibility of making rsync'ed disk bootable. So my question is: how to make rsync'ed hdd bootable under Linux or are there other 'quick backup' tools for Linux that would allow me to just swap drives? Or should I just stick to dd :( ?

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39  | Next Page >