Search Results

Search found 1236 results on 50 pages for 'nat'.

Page 34/50 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

• router w/ WOL out-of-the-box, or is known to work with open firmware

  - by Jaroslav Záruba

  I'm looking for a new WiFi router, and one key feature for me is WOL. Seems like many routers won't do this w/ factory firmware. Given my last router (Asus WL-520g) turned into a disco-brick couple hours after flashed to dd-wrt I'd prefer if the new one supported WOL out-of-the-box. other required features would be: dyndns service support port forwarding sometimes it is called "virtual server" I guess NAT loopback so I can access services running in my own network using dyndns hostname or public IP w/o getting too old (for example DIR-615 with factory firmware lets you wait literally minutes) did I mention WiFi? preferably w/ some range extending technology, if such stuff works at all

  Read the article

• Can't connect to VPN in Windows XP mode

  - by darkstar13

  I have Windows 7 x32 installed on my laptop. I have also Windows XP mode installed. My setup is that my work-remote programs are in Windows XP mode because my VPN installer in Windows XP only. Lately, I have been having troubles getting on / logging in to VPN. I can access the internet in WinXP mode but When I ping the IP address of the target IP of my VPN network (or even just Google.com), I always get a 'Request Timeout'. However, when I ping the same IP address in command prompt in Windows 7, I get 100% data sent. Is there anything I need to adjust? Before, I have been able to connect instantly. Now, it's like trial and error, or I will have to wait for hours just to be able to enter logon credentials in Cisco VPN dialer. NAT is my network adapter in XP mode.

  Read the article

• Force an LXC container to use its own IP address

  - by emma sculateur

  Sorry if this question has already been asked. I could not find it, I have this setup : +---------------------------------------------------------------------------------------------+ |HOST | | | | +-------------------------------------------------+ | | | UBUNTU-VM | | | | | | | | +-------------------+ | | | | |UBUNTU-LXC | | +------------------+ | | | | 10.0.0.3/24 | 10.0.0.1/24 | |OTHER VM | | | | | eth0-----lxcbr0----------eth0-----------br0----------eth0 | | | | | | 192.168.100.2/24| 192.168.100.1/24 |192.168.100.3/24 | | | | +-------------------+ | +------------------+ | | +-------------------------------------------------+ | +---------------------------------------------------------------------------------------------+ When I ping 192.168.100.3 from my UBUNTU-LXC, the source IP address is automatically changed to 192.168.100.2 by UBUNTU-VM. It's like having a NAT, whereas I really want my UBUNTU-LXC to talk with it own IP address. Is there any way to do this ? Edit : these info may be relevant : I am using KVM +libvirt to set up my VMs Here is how I create my interface in UBUNTU-VM : <interface type='bridge'> <mac address='52:54:00:cb:aa:74'/> <source bridge='br0'/> <model type='e1000'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x09' function='0x0'/> </interface>

  Read the article

• Accessing through VPN, which internet connection would be used

  - by Sriram

  I've a data card which has a limit of 2 GB up/download traffic per month. I've an office internet line which has an unlimited up/download. I've successfully connected to VPN using my data card and by changing certain configurations like DNS etc., have also been able to use my office line for internet (verified by doing a IP check - returns the static IP of our office). Now to my question - is it just a NAT which is happening or am I actually using my office line for all communication. Which one would reflect the usage/trace. The data card usage log at this moment does not reflect any usage (which is confusing since the VPN is over the data card connection). Further more (theoretically), would the net be any faster if my office line is let us say 8Mbps and the data card is 512kbps by doing this as against directly connecting the internet using the data card.

  Read the article

• is there any Open Source solution for Failover of incoming Traffic?

  - by sahil

  Hi, We have two ISP... and both ISP's Ip Nat with same Webserver IP, i want failover for incoming traffic , is there any open source solution? can i do it by making two name server , one for each ISP? ... I am not sure but as per my knowledge primary and secondary name server will reply in round robin method till they are live , once any name server will be unreachable then only another will be reply...so if i am right then i think i can do incoming failover by making two name server in my office... Waiting for your valuable response... Thanking you, Sahil

  Read the article

• External routing for local interfaces in a virtualized network

  - by Arkaitz Jimenez

  Current setup: br0| |-- tun10 -pipe-tun0(192.240.240.1) |-- tun11 -pipe-tun1(192.240.240.2) |-- tun12 -pipe-tun2(192.240.240.3) The pipe program is a custom program that forwards data back2back between two tun interfaces. The idea is puting 2 programs in .2 and .3 while keeping .1 as the local interface in the current machine. The main problem is that I want to route packets to .2 and to .3 through .1 and br0, but as they are local interfaces, the kernel ignores any routing instruction, it just delivers the packet to the proper interface. Tried iptables, but the nat table doesn't even see ping packets to those ifaces. A "ping 192.240.240.2" delivers a icmp packet with source and dest .2 to tun1, ideally it should deliver a source .1 dest .2 at tun1 through tun0-br0-tun1 Any hint? Here the output of some commands: Output

  Read the article

• What do you use to loadbalance IPv6 services?

  - by Michael Renner

  Hi, the current Linux software environment for IPv6 load balancing looks a bit grim. IPVS has rudimentary support for IPv6 but it's far from complete. NAT for IPv6 seems to be a no-go. Are there any other projects which aim for this goal? Does the IPv6 support in other OS look better? Are there any commercial products which have been successfully used in production environments with non-trivial load patterns? Or is it just that the time for IPv6 hasn't come... yet? ;) best regards, Michael

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• How to automatically restart RRAS service after OpenVPN

  - by JT

  I have OpenVPN set up on a Windows Server 2003 box using a routed configuration. This allows users to connect and access the work LAN subnet. There are remote hosts/services however that are only accessible when used via the work network. To enable access these, I push routes out to the clients to make sure traffic to these destinations goes across the VPN, and NAT the traffic using RRAS. This all works, except: if I restart the OpenVPN service, network traffic stops working until I restart the RRAS service as well. Is there a good way for me to make the RRAS service start/restart after OpenVPN? Are service dependencies the way to go? Obviously I could write a batch file to do this, but I'd like to make the process as bullet-proof and obvious as I can so it doesn't cause problems for other admins.

  Read the article

• Allow VMWare client to connect only via VPN

  - by Frank Meulenaar

  I have a VMWare (currently using Workstation on Vista, but thinking about switching to ESX) client with Windows XP. I've installed OpenVPN in the client and it connects to the corporate VPN server. I want to make sure that all traffic from the Windows XP machine goes trough this VPN tunnel, but I can't change any settings on the corporate VPN server. Is it possible to restrict the internet connectivity of the Windows XP client in such a way that it can only send packets to the IP of the corporate VPN server? In that way it'd be impossible for packets to bypass the tunnel. I've looked at NAT configurations but couldn't see how I could make this setup.

  Read the article

• Wrong source IP when accessing internet directly from TMG server

  - by jarod1701

  Hi everyone, after implementing a ForeFront TMG server I'm facing only one problem: After I added a second IP to the external adapter I had to manually set "NAT Address Selection" inside the network rule "Internet Access" to the first IP since all others would get blocked by the CISCO firewall. This configuration works as long as traffic comes from the internal network (e.g. browser on clients). Traffic from the TMG directed to the internet always carries the second IP as it's source address and gets blocked. All our other TMGs/ISAs are running fine and I never came across this problem- Does anybody have a clue, coz I don't?! Kevin

  Read the article

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• is there any Open Soruce solution for Failover of incoming Traffic?

  - by sahil

  Hi, We have two ISP... and both ISP's Ip Nat with same Webserver IP, i want failover for incoming traffic , is there any open source solution? can i do it by making two name server , one for each ISP? ... I am not sure but as per my knowledge primary and secondary name server will reply in round robin method till they are live , once any name server will be unreachable then only another will be reply...so if i am right then i think i can do incoming failover by making two name server in my office... Waiting for your valuable response... Thanking you, Sahil

  Read the article

• how to portforward port 7300 from server A to server B

  - by Patrick van Hout

  hi, We are using Stunnel. But want to replace it is with an iptables entry if possible. 192.168.123.122:7300 need to be forwarded to 192.168.123.188:7300. So in iptables I set these two entries: [root@dev ~]# iptables -t nat -A PREROUTING -p tcp --dport 7300 -j DNAT --to-destination 192.168.123.188:7300 [root@dev ~]# iptables -A FORWARD -m state -p tcp -d 192.168.123.188 --dport 7300 --state NEW,ESTABLISHED,RELATED -j ACCEPT But it isn't working. I did check that /proc/sys/net/ipv4/conf/eth0/forwarding has the value "1" inside. Any tips or hints? thanks, Patrick

  Read the article

• How to use CLEAR USB internet connection in Ubuntu (host) and WindowsXP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for linux as yet. I've installed windowsxp as guest in ubuntu and the version I'm using is 3.2.2. USB is connecting fine in WindowsXP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

• Problems connecting Centos to the network when running in VMWare

  - by Sakin

  Hi, I installed CentOs on VMware running on windows XP. When trying to configure it to connect to the internet, I get an error message when trying to bring up the network interface: [root@VMLinux ~]# /et/init.d/network start Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... failed [FAILED] VM is running on a machine that has access to the network, I tried it on two different networks that have DHCP enabled. I tried to configure VMWare to use a bridged connection as well as NAT connection. An image of Ubuntu runs fine on the same VMware. What am I missing here? Thanks.

  Read the article

• Access Bind9 DNS in Virtualbox on Host

  - by Philipp Melab

  I've set up a Ubuntu 10.04 Virtual Box with a Bind9 DNS server. The Box has a NAT Network connection for internet access and a host-only adapter for static ip connections from the host (OSX Lion). Thats the only way i managed to get internet and static ip inside the box, guess there is a better one ... The DNS works fine from inside the virtualbox, but not from the host. The http and ftp on the guest system is accessible via both addresses, so connection between host and guest are fine i guess. I tried to add both IP's as name servers. I'm completely new to Bind9 and DNS configuration. Anybody has a hint for me whats wrong? Or how i have to configure the DNS server?

  Read the article

• Get source and destination of outbound traffic in pfSense

  - by maxsilver

  I'm looking at the traffic graph in pfSense (Version 1.2.2), which we're using as a router / NAT / ect on our network. Recently, I'm seeing a sudden, constant spike of 15 - 30kbps traffic outbound, that is unusual for our network (normally its below 2kbps, we're mostly all inbound traffic) Is there any way to determine what the source of this traffic is, or where it's going? (Just an internal IP address for source, and external IP address for destination would be all I need) I've already tried switching the traffic graph to 'LAN' and watching the host list on the right side, but it seems ... flakey. The numbers it shows seem to fade in and out at random, and the values never add up to anywhere near the graph values. I'm not allowed to post the image, but a photo is available at - http://imgur.com/QYjKI.png

  Read the article

• GNS3 Cannot ping/resolve DNS record

  - by Eldad Cohen

  I set up an internet lab with GNS3, which has 3 routers, in each node there is a computer directly connected. One of the hosts is a DNS server, Windows 2003 Server. The other one is a Windows XP machine. Ping is good between routers and machines but no ability to ping domain.com record on DNS server 2003. I set a static nat on the router to route all traffic from gateway to the DNS server internal ip address, still no answer for the dns request. Any ideas or thoughts will be most welcome.

  Read the article

• CheckPoint VPN-1 SecureClient inability to navigate behind a Linksys WAG300N

  - by user46819

  I have a Linksys WAG300N, I'm accessing my LAN with Wifi and everything works fine on my Windows 7 Enterprise laptop. When I try to connect to my company's VPN the connection succeeds, but I cannot access any internet site either within my work network or public site like Yahoo or Google. In my Linksys control panel I already verified all types of VPNs are enable to passthrough. Normal IPSec and Windows VPN worked in the past without any problems. CheckPoint seems to have a solution, but I do not have the ability to change the IP in my client and of course using another NAT device in between is not a solution for me. Edit: adding link to the Checkpoint solution, https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=sk26189

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

• Configure Windows Routes for VPN

  - by Florin Sabau

  I have a Virtual PC/VMWare machine that runs Windows Server 2003. This virtual machine uses an IPSec VPN client program to connect to a remote network. I configured the virtual machine to have 2 NICs: NAT - to be used by the VPN Client to access the remote network Host only - to be able to access the virtual machine from the host The reason I have this setup is because I want to be able to access some remote network from the host machine. I could've installed the VPN client on the host machine, but the host runs Windows 7 and the client doesn't support it. The problem: although the virtual machine is normally reachable (ping + http access), as soon as the VPN client is started, neither of the NIC addresses are reachable anymore. I'm wondering if it is a routing problem that needs to be addressed? How do routing/VPN client connection affect the ability of the server to respond to client requests from the host?

  Read the article

• Linksys EA3500 : use WAN port as WAN + LAN possible?

  - by Dough

  I'm waiting for deliver of a Linksys EA3500 router. I was wondering if it was possible to get the WAN port act as normal WAN port (Internet IP) + LAN switch ? My problem is that my Internet box is in a room with NAS and PC, and the router will be in another room with TV, PS3 and PC. The Internet box have a 4 port Gigabit switch so one cable will plug from there to the router's WAN in the other room. The router will get the Internet IP from the Internet box, but will it be possible to have private network through this link too ? I could have a first network between the Internet box and the router, and another network form router and devices but that will do double NAT for nothing... Thanks for reading me and your help !

  Read the article

• Unable to launch google.com inside Linux Ubuntu

  - by Anuradha

  I have installed Ubuntu Linux VM in my Win XP box. I am able to open http://google.com on Win XP but when I login to, ubuntu linux.. and launch this site: I am getting an error: Server not found. The network settings I have on LinuxUbuntu VM is : Adapter1 : attached to Bridge adapter. I tried NAT as well. But nothing seems to work. I am not in China. I provide google.com as mere example. We have a test website which cannot be launched inside Linux Ubuntu.

  Read the article

• virtualbox ftp hangs on list command

  - by Tiddo

  Hi all, I have virtual box installed on a windows 7 64-bit computer, with Cent OS 5.5 as guest os. I want to be able to use ftp between those. I've installed vsftpd on the guest os, and the guest os uses a nat connection with the host os for internet. So far, I am able to connect to the guest os using ftp (in filezilla), but after the list command is executed, nothing happens, until the command is timed out. This happens in both active and passive mode. I do have set a pasv_min/max_port in the vsftpd.conf file, listing is enabled, and the ports are redirected in virtualbox. Also the ftp_data_port is set to 20. I also tried setting the pasv_address, but I had to set it to 127.0.0.1, but than filezilla gives me this: Command: PASV Response: 500 OOPS: bad family Command: PORT 127,0,0,1,139,204 Response: 500 OOPS: child died Can someone help me with this?

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >