Search Results

Search found 4467 results on 179 pages for 'red rover'.

Page 34/179 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

• Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

  - by user95917

  hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

  Read the article

• How to change image to this color?

  - by askmoo

  I have this image And I need to change it to the color #D21108 (type of RED). Of course, I do not want to paint it to this color, but to change the color to #D21108 and its shades (like I do in Photoshop via Brush Colour Replacement). I have all info about this color, values of RGB, CMYK, Lab and HSV if you need them. Now, I guess I can easily change it via GIMP's menu "Colors". I tried options Color Balance, Hue-Saturation, Colorize, but I did not find a way to enter the starting color I need. I was closest to my aim via Hue-Saturation, but I could not get this red value, no matter what I tried. As I am not a graphics expert, please tell me how to accomplish this task. PS. What's the meaning of Lab and HSV in the color scheme? I know the meaning of RGB and CMYK.

  Read the article

• Merit and demerits for various Linux fiberchannel multipath options

  - by wzzrd

  On our Linux servers, we currently use HPs qla2xxx drivers, because it has multipathing (active/passive) built in. The are, however, various other options, like Red Hats device-mapper-multipath with the stock qla2xxx drivers (multibus and failover) and things like SecurePath and PowerPath (both of which can do trunking, iirc). Can someone tell me what the merits and demerits of the various options are (if I can ask such a question), besides the obvious fact that the {Secure,Power}Path options cost vast amounts of money? I'm mainly interested in the freely available options, like HPs qla2xxx vs. Red Hats multipathd and possible other open source solutions, but I would like to hear good reasons to go for the commercial solutions too. UPDATE: I'll be benchmarking various options the coming few days (the average of 10 runs of iozone for each option (options being native qla2xxx failver, native qla2xxx multibus, HP qla2xxx failover)). I'll post a summary of results here for those interested.

  Read the article

• All of ESX4 hosts not responding after rebooting vCenter server

  - by hojyokinmo

  Hello I'm constructing 5ESX+a vCenter serv. I'm testing FT on the system. Today vCenter OS (W2008) demanded system reboot. After rebooting vCenter Serv. All of ESX hosts have alert icon. end indicate "not responding" I tried to connect ESX (version 4) hosts to vCenter again. Once they came back normally, but after few seconds ,They turned red again. All of them have ping connection to vCenter serv. There are no red messages in Tusks and events. Two messages are found in Summary of Cluster ·There aren't sufficient resource for HA failover. ·Can't contact primary HA agent. I'm also not able to reset FT configuration because all of VMS aren't accessed from vCenter What should I do?

  Read the article

• Mother Board Question

  - by user33931

  1st, I am software guy. I do not do hardware. So I know to you hardware geeks, this is a dumb question. I just inherited a box with a ASUS P5GZ-MX mother board. I have attempted to install two nVidia PCI video cards. I put a 750w power supply in the system to be sure I have enough power. With no extra video cards, the 3.3 v shows normal. When I put one card in, the 3.3 goes to 3.5-3.6 and flashes red (over voltage) about 30% of the time. When I put the 2nd card in, it goes to 3.73 v and stays red all the time. Any Ideas why the voltage goes up when I add cards instead of going down? More Importantly, is this dangerous to the system?

  Read the article

• How can I compare two columns in Excel to highlight words that don't match?

  - by Jez Vander Brown

  (I'm using Microsoft excel 2010) OK, lets say I have a list of phrases in both column A and column B (see screen shot below) What I would like to happen whether it be with a macro, VBA or formula is: If there is a word in any cell in column A that isn't any of the words in any cell in column B to highlight that word in red. For example: in cell A9 the word "buy" is there, but the word buy isn't mentioned anywhere in column B so i would like the word buy to highlight in red. How can I accomplish this? (I think a macro/vba would be the best option but I have no idea how to create it, or even if its possible.)

  Read the article

• being able to solve google code jam problem sets

  - by JPro

  This is not a homework question, but rather my intention to know if this is what it takes to learn programming. I keep loggin into TopCoder not to actually participate but to get the basic understand of how the problems are solved. But to my knowledge I don't understand what the problem is and how to translate the problem into an algorithm that can solve it. Just now I happen to look at ACM ICPC 2010 World Finals which is being held in china. The teams were given problem sets and one of them is this: Given at most 100 points on a plan with distinct x-coordinates, find the shortest cycle that passes through each point exactly once, goes from the leftmost point always to the right until it reaches the rightmost point, then goes always to the left until it gets back to the leftmost point. Additionally, two points are given such that the the path from left to right contains the first point, and the path from right to left contains the second point. This seems to be a very simple DP: after processing the last k points, and with the first path ending in point a and the second path ending in point b, what is the smallest total length to achieve that? This is O(n^2) states, transitions in O(n). We deal with the two special points by forcing the first path to contain the first one, and the second path contain the second one. Now I have no idea what I am supposed to solve after reading the problem set. and there's an other one from google code jam: Problem In a big, square room there are two point light sources: one is red and the other is green. There are also n circular pillars. Light travels in straight lines and is absorbed by walls and pillars. The pillars therefore cast shadows: they do not let light through. There are places in the room where no light reaches (black), where only one of the two light sources reaches (red or green), and places where both lights reach (yellow). Compute the total area of each of the four colors in the room. Do not include the area of the pillars. Input * One line containing the number of test cases, T. Each test case contains, in order: * One line containing the coordinates x, y of the red light source. * One line containing the coordinates x, y of the green light source. * One line containing the number of pillars n. * n lines describing the pillars. Each contains 3 numbers x, y, r. The pillar is a disk with the center (x, y) and radius r. The room is the square described by 0 = x, y = 100. Pillars, room walls and light sources are all disjoint, they do not overlap or touch. Output For each test case, output: Case #X: black area red area green area yellow area Is it required that people who program should be should be able to solve these type of problems? I would apprecite if anyone can help me interpret the google code jam problem set as I wish to participate in this years Code Jam to see if I can do anthing or not. Thanks.

  Read the article

• Move flag for follow of a specific color to a folder in Outlook 2003

  - by Campo

  I have a user request to be able to create a rule that would move an email in outlook 2003 that the user flagged for follow up to a specific folder. That seemed simple enough till he requested that depending on the flag color they were to be moved to a specific folder. Issue is that in outlook 2003 that's not an option when creating a rule. I know that this is very straight forward in outlook 2007 and 2010 and using the categories feature is very convenient as it displays as a list when you right click.... Though in 2003 categories are not so convenient. as an example the user will flag for follow up as so... Red Flag for sales Blue Flag for requests Green Flag for personal They want a rule that will move all items with a red flag to the sales folder, Green flag to the requests folder and so on.... Thank you for your suggestions.

  Read the article

• How to calibrate a HDTV that is being used as monitor?

  - by Mike

  I have a HDTV I am using as a second monitor. The first monitor, is a real computer monitor, not a TV and has a fantastic image. The second one, the HDTV has a good image, but it is a little bit blurred and has the problem you can see on the picture below, a kind of red halo around the edges. I think it has something to do with red contrast. Other colors show this problem too, specially the green. The problem is that the TV has no contrast adjustment. Instead it has something called IRE 10 points and IRE 2 points. Taking IRE 10 for example, it has 4 controls for each of the 10 points: luminosity, R, G and B. I could not find a page where I can understand what this IRE is and how should I adjust this. Can someone tell me how should I proceed to calibrate this TV for best picture? thanks for any help.

  Read the article

• Bit of python help

  - by user42780

  I've tried to get this to work, but it just freezes. It should display a pyramid, but all it does is.. halts. from graphics import * valid_colours = ['red', 'blue', 'yellow', 'green'] colour = ['', '', ''] while True: colour[0] = raw_input("Enter your first colour: ") colour[1] = raw_input("Enter your second colour: ") colour[2] = raw_input("Enter your third colour: ") if ((colour[0] and colour[1] and colour[2]) in valid_colours): break while True: width = raw_input("Enter a width between 2-7: ") if width.isdigit(): if (int(width) <= 7 and int(width) >= 2): break width = int(width) win = GraphWin("My Mini Project ", 1000, 1000) # 1000 \ 20 = 50 win.setCoords(0 , 0 , 20, 20) p1 = [0, 2] while width > 0: p = [1, 3] loopWidth = 0 while loopWidth < width: loopWidth = loopWidth + 1 c = 0 while c <= 10: c = c + 1 if c % 2: colour = "white" else: colour = "red" rectangle = Rectangle(Point(p[0],p1[0]), Point(p[1], p1[1])) rectangle.setFill(colour) rectangle.setOutline("black") rectangle.draw(win) p[0] = p[0] + 0.2 p1[0] = p1[0] + 0.2 p[0] = p[0] - 2 p1[0] = p1[0] - 2 p[0] = p[0] + 2 p[1] = p[1] + 2 width = width - 1 p1[0] = p1[0] + 2 p1[1] = p1[1] + 2

  Read the article

• Tmux causes Emacs glitch

  - by killy9999

  Recently I started using Tmux, but I noticed that it causes a strange Emacs glitch. When I open source code for elisp or haskell, the comments aren't highlighted. Only the comment sign is (; in case of elisp, -- in case of haskell). The rest of the commented line is in normal colour. When I run Emacs outside of Tmux everything works as expected - the whole commented line is highlighted in a colour denoting a comment. Any ideas why this is happening? SOLUTION: Based on Stefan's comment I added this to my .emacs file: (custom-set-variables (custom-set-faces '(font-lock-comment-face ((((class color) (min-colors 8) (background dark)) (:foreground "red")))))) Now the comments are displayed in red, just like comment delimiters.

  Read the article

• Installing Apache to CentOs 5.7 (problems with repo)

  - by C.S.Putra

  I'm installing Apache on CentOS 5.7, I followed instructions here : http://www.if-not-true-then-false.com/2010/install-apache-php-on-fedora-centos-red-hat-rhel/ I've installed this also : Remi Dependency on CentOS 5 and Red Hat (RHEL) 5 ## rpm -Uvh http://download.fedora.redhat.com/pub/epel/5/i386/epel-release-5-4.noarch.rpm When I install this, there's warning: /var/tmp/rpm-xfer.Bqu2xo: Header V3 DSA signature: NOKEY, key ID 217521f6 But it says that the package is alread installed. Then I move on to 3rd steps: yum --enablerepo=remi install httpd php php-common But it says: error getting repository data for remi, repository not found. Why is it like that?

  Read the article

• Looking for an easier Skype video chat alternative

  - by Paul

  Is there any software 'easier to use' than Skype - ie to get a video conversation going you have to turn on the computer, make sure the speakers are turned on, make sure the web cam is connected, make sure you click answer with Video... I would like to buy a 'single red button' which does all of the above. - Any recommendations? Update @Eric Koslow comment My original question title was "Is there any software/hardware 'easier to use' than Skype?" So the answer is not necessarily a computer running a program, although it might be. I realise Skype makes a good attempt at helping to ensure speakers and web cam are working and helps you to sort them out if they are not, and for a person who isnt computer phobic this should be enough. However I am interested if there is anything available that is 'easier' than this - ie I'm looking for my 'single' red button. ie the mobile phone with video call maybe the closest answer so far, but I would prefer something as 'free' as Skype is.

  Read the article

• How do I know if IP Multicasting is enabled on my network?

  - by Swapnonil Mukherjee

  Is there a way to know if the Red Hat Linux Servers on my network have IP Multicasting enabled?

  Read the article

• 3 wire computer fan won't run continuously

  - by Ben

  I had an old computer that didn't work anymore, so I took the CPU fan out to see what I could make with it. The fan is NMB model number BG0903-B044-VTL, like this. It has three wires coming off of it, red, black, and white. I know that the white wire is usually a speed sensor. Does this wire need to be connected to something in order for the fan to run continuously? Right now when I apply power to the red and black wires (from a 9-volt battery) the fan will spin very briefly, and then slow down until it stops. The fan's motor only spins in the instant that the power is turned on, but doesn't continue, even though the power is still applied. How can I get the fan to spin continuously?

  Read the article

• How do I install automake and autoconf on RedHat Enterprise 5?

  - by Kevin Sedgley

  I am attempting to install "uploadprogress" for a PHP application, and have failed on dependencies. Firstly, on phpize, then php-devel, then on autoconf and automake. I have tried yum, and various repositories, with no luck. I think it's to do with the ultra-tight but annoying set up they have on Rackspace Cloud servers. Does anyone know where I can find a repository that I can tell yum to look at that will contain php-devel, autoconf, automake, etc? Thanks ever so much. Release details: Red Hat Enterprise Linux Server release 5.3 (Tikanga) Linux version 2.6.18-128.7.1.el5xen ([email protected]) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44)) #1 SMP Wed Aug 19 04:17:26 EDT 2009 Linux Serv001 2.6.18-128.7.1.el5xen #1 SMP Wed Aug 19 04:17:26 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• rsync osx to linux

  - by Nick

  I did a backup to a remote nfs folder with rsync, from a MAC to a Remote Debian. The final backup is 58GB less than the original. Rsync says that everything was OK, and nothing to update. Macintosh:/Volumes/Data1 root# du -sh Produccion/ 319G Produccion/ root@Disketera:/mnt/soho_storage/samba/shares# du -sh Produccion/ 260G Produccion/ can I trust in rsync? I'm using rsync -av --stats /Volumes/Data1/Produccion/ /mnt/red/ (/mnt/red is my samba mountpoint) Some differents folders root@Disketera:/mnt/soho_storage/samba/shares/Produccion/tiposok# du -sh * 0 IndoSanBol 0 IndoSans-Bold 0 IndoSans-Italic 0 IndoSans-Light 0 IndoSans-Regular 40K PalatinoLTStd-Black.otf 40K PalatinoLTStd-BlackItalic.otf 40K PalatinoLTStd-Bold.otf 44K PalatinoLTStd-BoldItalic.otf 44K PalatinoLTStd-Italic.otf 40K PalatinoLTStd-Light.otf 40K PalatinoLTStd-LightItalic.otf 40K PalatinoLTStd-Medium.otf 40K PalatinoLTStd-MediumItalic.otf 56K PalatinoLTStd-Roman.otf 12K TCL IndoSans_mac Macintosh:/Volumes/Data1/Produccion/tiposok root# du -sh * 36K IndoSanBol 40K IndoSans-Bold 36K IndoSans-Italic 36K IndoSans-Light 36K IndoSans-Regular 40K PalatinoLTStd-Black.otf 40K PalatinoLTStd-BlackItalic.otf 40K PalatinoLTStd-Bold.otf 44K PalatinoLTStd-BoldItalic.otf 44K PalatinoLTStd-Italic.otf 40K PalatinoLTStd-Light.otf 40K PalatinoLTStd-LightItalic.otf 40K PalatinoLTStd-Medium.otf 40K PalatinoLTStd-MediumItalic.otf 56K PalatinoLTStd-Roman.otf 160K TCL IndoSans_mac

  Read the article

• In Outlook 2013, the reading pane does not display images correctly for most emails (but does for some)

  - by smoldyr

  I am running Microsoft Office Outlook 2013 on Windows 7 Enterprise. When I click on an email in the list of messages, the preview of the message in the reading pane usually will not show the images contained in the email, but instead will show a red 'X'. Sometimes this red 'X' is followed by the text "The linked image cannot be displayed. The file may have been moved, renmaed, or deleted. Verify that the link points to the correct file and location." I am using an IMAP email account. The really strange thing is that for some emails, the images will display, although they take a long time to load. How can I make the images show up in the reading pane?

  Read the article

• How can I copy and paste formatted text in Excel?

  - by Landy

  Before I ask question, I've searched but only found ways of copy and paste "formatted cell". That's not what I need. I want to use an example to explain my requirement: There are 2 cells in a sheet. Cell_A's text is "aaaaabbbbb", and "aaaaa" is green, and "bbbbb" is red. Cell_B's text is "ccccc" and "ccccc" is black. I want to copy and paste "bbbbb" from Cell_A to Cell_B and keep "bbbbb" in red. But in my environment(Office 2007), "bbbbb" is changed to black as "ccccc", the default format of Cell_B. Is there an easy way to implement my requirement?

  Read the article

• Is it safe to expect Sun Java 6 to supported for the life of RHEL 6?

  - by Ophidian

  I'm in the planning stages of a java application that we're targeting for Red Hat Enterprise Linux 6. Unfortunately, we're stuck at RHEL 6.1 which does not ship the java-1.7.0-oracle package set (they were added in 6.3) and I don't really have any control over when we will be upgraded to the more recent version. I don't have any specific technical requirements to use Java 7, but Java 6 is going to hit public EOL in February 2013. Am I safe to assume that since Red Hat (and subsequently Oracle with its Oracle Unbreakable Linux) has shipped a copy of Java 6 in the java-1.6.0-sun package, it will support it for the entire 10 year support life of RHEL6?

  Read the article

• Windows 7 doesn't connect to mapped drives at start up.....

  - by danbo

  We are testing Windows 7 (32bit version) and logon to a windows 2003 domain that runs a logon script whichs maps our drive letters. We have no control over the domain. Of our 7 test users, 5 continually recieve red X's on their network drives after they logon. Double clicking on them connects the drives, however, any aplpication that requires files on the fileserver will fail since it thinks it has no connection to the drive. We have tried several reg edits (Enable Linked connections, KeepConn), we have tried to find information in the event viewer to no avail. We have also looked at any differences in NIC driver versions (none). The other 2 computers that can connect without problem are local admins, but, if we logon to the 5 that have the problem with the local admin credentials we get the red x's as well??? This one is a real head scratcher......

  Read the article

• Export to excel - COMMA issue

  - by 6242Y

  I want to put a string in an excel sheet from my Export to excel function. However my string is as follows: string : Red, red wine Go to my head Make me forget that I Still need and on my excel I get unexpected results , column change after comma and also column change when there is no full stop in front of an UPPER CASE alphabet. The Upper case alphabets (without a full stop before them) are also causing this (Go , Make . Still) How can I solve this issue ? I tried removing the spaces after the comma as var desc = ""; if (o.Description.Contains(',')) { var trimmedSplits = new List<string>(); var splits = o.Description.Split(','); foreach (var stringBits in splits) { desc = desc + stringBits.Trim() + ","; } desc = desc.Remove(desc.Length - 1); } dtRow[(int)ProductRangeExportToExcel.Description] = desc;

  Read the article

• ComboBox values disappears after selected when objects used for display

  - by Gakk

  I have a combobox where I want to display objects and have enum values returned. When first opened the combobox displays the items as supposed, but after a value is chosen it seems to disappear from the list. But if the combobox is active I can use the keyboard to navigate up and down between the other values, so they are in the list but only invisible. I have created a little test application to show my problem. When started the application shows the combobox with all the choices (the two first are type of Object, the third is a String): After the blue line is selected and when the combobox is opened again this line is missing: When the line with the text "Green" is selected that line is still showing: If I had chosen the red line the only thing that would still be in the list is the test "Green". I am using .NET Framework 3.5. Any hints or tips to why the elements disappears? Here are all the code needed after starting a blank project in Visual Studio. MainWindow.xaml.cs: using System; using System.Collections.Generic; using System.Diagnostics; namespace Test { public partial class MainWindow { public MainWindow() { InitializeComponent(); } private ColorComboBoxValue _activeColor; public ColorComboBoxValue ActiveColor { get { return _activeColor; } set { _activeColor = value; Debug.WriteLine("ActiveColor: " + _activeColor.Color); } } } public class ColorList : List<ColorComboBoxValue> { } public class ColorComboBoxValue { public Color Color { get; set; } public Object Object { get; set; } } public enum Color { Red, Blue, Green } } MainWindow.xaml: <Window x:Class="Test.MainWindow" x:Name="window" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:System="clr-namespace:System;assembly=mscorlib" xmlns:local="clr-namespace:Test" Title="ComboBoxTest" Height="100" Width="200"> <Window.Resources> <local:ColorList x:Key="ColorList"> <local:ColorComboBoxValue Color="Red"> <local:ColorComboBoxValue.Object> <Path Data="M0,0 L0,30 60,30 60,0 Z" Fill="Red"/> </local:ColorComboBoxValue.Object> </local:ColorComboBoxValue> <local:ColorComboBoxValue Color="Blue"> <local:ColorComboBoxValue.Object> <Path Data="M0,0 L0,30 60,30 60,0 Z" Fill="Blue"/> </local:ColorComboBoxValue.Object> </local:ColorComboBoxValue> <local:ColorComboBoxValue Color="Green"> <local:ColorComboBoxValue.Object> <System:String>Green</System:String> </local:ColorComboBoxValue.Object> </local:ColorComboBoxValue> </local:ColorList> </Window.Resources> <ComboBox ItemsSource="{Binding Source={StaticResource ColorList}}" SelectedItem="{Binding ActiveColor, ElementName=window}"> <ComboBox.ItemTemplate> <DataTemplate> <ContentPresenter Content="{Binding Path=Object}"/> </DataTemplate> </ComboBox.ItemTemplate> </ComboBox> </Window>

  Read the article

• Disabled annotation tools in Skim

  - by Kit

  Here's a portion of the toolbar in Skim In the Add Note section, why are the following tools disabled (dimmed)? Add New Highlight (A in the yellow box) Add New Underline (red line under A) Add New Strike Out (A struck out by red line) However, in the Tool Mode section, there is a drop down button (shown as active in the screenshot). To illustrate, I can select and use the Add New Underline tool, as well as the other tools I mentioned above, using the drop down button. But those tools are dimmed out in the Add Note section. Why? I have observed that the drop down button is just a duplicate of the Add Note section. Why not just enable all the buttons in the Add Note section and save the user from making an extra click just to bring down a list of tools? Is this because of some property of the presently open PDF, or what?

  Read the article

• XHTML 1.0 DocType ignored in all browsers?

  - by John

  I was testing this, since I understood using XHTML let me use any valid XML for empty <div> elements: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html> <head> <meta http-equiv="Content-Type" content="text/html;charset=utf-8"> <title>Test</title> </head> <body> <div style="border:solid 10px black; width:100px; height:100px"></div> <div style="border:solid 10px red; width:100px; height:100px"></div> <div style="border:solid 10px blue; width:100px; height:100px"></div> <div style="border:solid 10px black; width:100px; height:100px" /> <div style="border:solid 10px red; width:100px; height:100px" /> <div style="border:solid 10px blue; width:100px; height:100px" /> </body> </html> It doesn't work in any browser I try... this is how FireBug tells me it understands the document: <html> <head> <meta content="text/html;charset=utf-8" http-equiv="Content-Type"/> <title>Test</title> </head> <body> <div style="border: 10px solid black; width: 100px; height: 100px;"/> <div style="border: 10px solid red; width: 100px; height: 100px;"/> <div style="border: 10px solid blue; width: 100px; height: 100px;"/> <div style="border: 10px solid black; width: 100px; height: 100px;"> <div style="border: 10px solid red; width: 100px; height: 100px;"> <div style="border: 10px solid blue; width: 100px; height: 100px;"/> </div> </div> </body> </html> I'm a bit confused what the point is of using XHTML if I have to do this, I might as well just use HTML? Note, that setting the content type to content="application/xhtml+xml" makes no difference in FF3 at least.

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >