Search Results

Search found 2022 results on 81 pages for 'subnet mask'.

Page 34/81 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

  • Ethernet connection for Internet

    - by user103173
    I have just installed the Ubuntu 11.10 and facing challenges connecting to Internet using Ethernet connection. Below is the configuration details: IP address: 172.19.40.16 Subnet mask: 255.255.255.0 Default gateway: 172.19.40.1 When I run the command ifconfig I don't find the IP address in inet addr: Even when I try to change the Network device to "Ethernet" in Network tools, the changes are not getting saved. Please help. Let me know if you want further information.

    Read the article

  • Can't access local network when connect to pppoe

    - by shantanu
    I am using DSL(PPPOE) connection in ubuntu. It has two part (I am not sure), when I just connect the cable, system automatically get an IP address started with 172.x.x.x(DHCP). When I connect using username/password (PPPOE) I get another IP started with 10.x.x.x and can access internet but can't access some local IP (in my LAN), which are some FTP, media server provided by my ISP. I complained about that to my ISP but they reply Windows is working It's true, Windows 7 is working fine with this settings. I can access internet and local server at the same time. Also I use a WIFI router (TP-link TL-WR340G/TL-WR340GD) which result the same problem. So when I connect cable directly to system and use Windows 7 than everything is fine. Otherwise problem. Similar problem discussed here. Edit before connect. route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.100.0.1 0.0.0.0 UG 0 0 0 eth0 172.100.0.0 0.0.0.0 255.255.0.0 U 1 0 0 eth0 after connect. Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.12.44.91 0.0.0.0 UG 0 0 0 ppp0 10.12.44.91 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 ifconfig after connect eth0 Link encap:Ethernet HWaddr 74:d0:2b:d5:b3:6c inet6 addr: fe80::76d0:2bff:fed5:b36c/64 Scope:Link inet6 addr: 2002:ac64:154:c:76d0:2bff:fed5:b36c/64 Scope:Global inet6 addr: fec0::c:76d0:2bff:fed5:b36c/64 Scope:Site UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:26582 errors:0 dropped:18 overruns:0 frame:0 TX packets:2340 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2542063 (2.5 MB) TX bytes:244938 (244.9 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4118 errors:0 dropped:0 overruns:0 frame:0 TX packets:4118 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:336759 (336.7 KB) TX bytes:336759 (336.7 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:10.12.44.95 P-t-P:10.12.44.91 Mask:255.255.255.255 inet6 addr: fe80::a536:c7ae:e079:d88d/10 Scope:Link UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:689 errors:0 dropped:0 overruns:0 frame:0 TX packets:744 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:385746 (385.7 KB) TX bytes:75296 (75.2 KB) I used network manager to create network(DSL connection)

    Read the article

  • Ubuntu systematically losing wired connection

    - by Lukasz Baczynski
    I'm working on 11.10 for few recent days, everything was working perfect until today. Updated ubuntu (some certs were updates as far as i remember) and from this time, wired network stops working randomly and systematically. (All other pcs/macs work fine) From 192.168.0.9 icmp_seq=25 Destination Host Unreachable From 192.168.0.9 icmp_seq=26 Destination Host Unreachable From 192.168.0.9 icmp_seq=27 Destination Host Unreachable From 192.168.0.9 icmp_seq=28 Destination Host Unreachable From 192.168.0.9 icmp_seq=29 Destination Host Unreachable From 192.168.0.9 icmp_seq=30 Destination Host Unreachable From 192.168.0.9 icmp_seq=31 Destination Host Unreachable 64 bytes from 192.168.0.1: icmp_req=32 ttl=64 time=1003 ms 64 bytes from 192.168.0.1: icmp_req=33 ttl=64 time=0.496 ms 64 bytes from 192.168.0.1: icmp_req=34 ttl=64 time=0.576 ms 64 bytes from 192.168.0.1: icmp_req=35 ttl=64 time=0.522 ms 64 bytes from 192.168.0.1: icmp_req=36 ttl=64 time=0.624 ms 64 bytes from 192.168.0.1: icmp_req=37 ttl=64 time=0.625 ms 64 bytes from 192.168.0.1: icmp_req=38 ttl=64 time=0.555 ms It'll work for 20 seconds then it'll stop working for 10-30sec and so on. I've tried setting my router to give static IPs, it doesn't help. NOTHING has been changed since yesterday beside the package update... Here are other settings that may be useful: baka@baka-PC:~/Private/projects/wduk$ lspci -nnk | grep -iA2 net 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432] Kernel driver in use: r8169 baka@baka-PC:~/Private/projects/wduk$ ifconfig -a eth0 Link encap:Ethernet HWaddr **Removed MAC address** inet addr:192.168.0.9 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:fe0a:85b2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6400 errors:0 dropped:6400 overruns:0 frame:6400 TX packets:7085 errors:0 dropped:107 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4191983 (4.1 MB) TX bytes:886881 (886.8 KB) Interrupt:72 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2522 errors:0 dropped:0 overruns:0 frame:0 TX packets:2522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1070130 (1.0 MB) TX bytes:1070130 (1.0 MB) baka@baka-PC:~/Private/projects/wduk$ cat /etc/resolv.conf # Generated by NetworkManager nameserver 8.8.8.8 thanks for help

    Read the article

  • How to get wireless (Alfa) operate in full power and speed up wireless Internet?

    - by MahboobeAlam
    I am using Wireless to connect to the internet (router). My laptop has Atheros wireless (AR 242x/542x) adapter but the router is a little bit far-away from my room so I have to use an external wireless adapter i.e. Alfa (Realtek 8187) for connectivity. However, since I have started using Ubuntu I noticed that Alfa is not working in full power, internet speed in Ubuntu is much slower than in Windows on my laptop. When I am using Windows 7 the LED (bulb) on Alfa blinks as it should, but when in Ubuntu, it doesn't blink rather it is on but very dim. Connection using Atheros adapter is also the same (slow)... I have tried 4 methods (I found on the Internet) to troubleshoot this matter but no success. It seems to me that Ubuntu/Linux is not letting these wireless adapters to operate in full strength. iwconfig shows that power management is off for both. So what's the problem? Details: ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:16:1e:36:ec UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1657 errors:0 dropped:0 overruns:0 frame:0 TX packets:1657 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:241697 (241.6 KB) TX bytes:241697 (241.6 KB) wlan0 Link encap:Ethernet HWaddr 00:22:5f:9b:24:b5 inet6 addr: fe80::222:5fff:fe9b:24b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:715460 errors:0 dropped:0 overruns:0 frame:0 TX packets:694246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:493539292 (493.5 MB) TX bytes:235159393 (235.1 MB) wlan1 Link encap:Ethernet HWaddr 00:c0:ca:42:14:62 inet addr:192.168.100.102 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::2c0:caff:fe42:1462/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:171053 errors:0 dropped:0 overruns:0 frame:0 TX packets:181363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:74094659 (74.0 MB) TX bytes:59474204 (59.4 MB) iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off wlan1 IEEE 802.11bg ESSID:"Zia" Mode:Managed Frequency:2.412 GHz Access Point: 00:0D:F0:9C:A6:18 Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-31 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:204 Invalid misc:6610 Missed beacon:0

    Read the article

  • Ubuntu Server Cannot Route to the Internet

    - by ejes
    I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

    Read the article

  • Ubuntu Server and setting up two nic cards

    - by kmalik
    I have ubuntu server on a computer with a wireless and hardwired nic card. The wireless needs to get the internet and pass it to the ubuntu server as well as pass it along to the hardwired nic card to more computers. I am having issues getting the basic set up as I believe the route table is grabbing from the wrong nic card. The router is 192.168.1.0 and the server is set to 192.168.1.11 on the wireless card through DHCP ETH0 (wired nic card) is set up to be 10.10.10.0 and the server is 10.10.10.1) I am not a linux or networking guru but basically I am trying to have internet come from a guest network 192.168.1.0 i believe to give internet to the ubuntu server then the ubuntu server will also A) have the wired nic serve DHCP addresses to other computers via a switch or router (that acts as a switch) via 10.10.10.0 addresses. And I would love if it also passed along internet capabilities as well if possible. Bu really at this point my hope is to at least get the internet working on the server and the DHCP to pass correctly. At the moment the specific issue I am having is getting ubuntu server to connect to the internet and have both nic cards up and running correctly. Any help would be appreciated! The route table is as follows: Destination Gateway GM Flags Metric Iface 0.0.0.0 10.10.10.1 0.0.0.0 UG 100 eth0 10.10.10.0 0.0.0.0 255.255.255.0 U 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 eth0 1992.168.1.0 0.0.0.0 255.255.255.255.0 U 0 eth1 My interfaces is set up as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.10.10.1 netmask 255.255.255.0 network 10.10.10.0 broadcast 10.10.10.255 gateway 10.10.10.1 domain-name-servers 192.168.1.0 auto eth1 iface eth1 inet dhcp netmask 255.255.255.0 gateway 192.168.1.0 wpa-driver wext wpa-ssid "ssid_name" wpa-ap-scan 1 wpa-proto wpa wpa-pairwise ccmp wpa-group ccmp wpa-key-mgmt wpa-psk wpa-psk "HASH" My DHCPD.conf (as there is a domain name server on here is as follows): ddns-update-style none default-lease-time 600 max-lease-time 7200 authoritative option domain-name "Kamron's Network" option subnet-mask 255.255.255.0 option broadcast-address 10.10.10.255 option routers 192.168.1.0 option domain-name-server 192.168.1.0 98.223.128.213 ooption subnet 10.10.10.0 netmask 255.255.255.0 { range 10.10.10.10 10.10.10.99 } log-facility local7

    Read the article

  • WiFi connected to router, but no internet connection

    - by Quetzacotl
    I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

    Read the article

  • Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

    - by Donal
    I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

    Read the article

  • No client internet access when setting up these iptables rules

    - by Siriss
    I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

    Read the article

  • Allow shutdown/restart if logged in another terminal

    - by user20415
    I have Natty installed. Howto allow shutdown/restart if other user logged in another terminal, for example using CTRL-ALT-DEL? I've tried to add the following lines in /etc/sudoers: user ALL=(root)NOPASSWD:/sbin/reboot user ALL=(root)NOPASSWD:/sbin/halt user ALL=(root)NOPASSWD:/sbin/shutdown and sudo chmod 750 /sbin/shutdown sudo chmod 750 /sbin/reboot or create /etc/shutdown.allow but it doesn't help and I still get Gnome login mask.

    Read the article

  • Step-by-Step: Implementing Hyper-V Network Virtualization with Windows Server 2012

    - by KeithMayer
    True network and virtual machine portability - that's the ultimate goal of Hyper-V Network Virtualization - allowing you, as an IT Pro, to align changing business needs with the best physical resource locations to run your VMs and network services - easily, without the sweeping network, router, switch, firewall and DNS changes with which we'd traditionally be plagued when merely attempting the feat of relocating VMs to a new rack, subnet or data center ... WOW!

    Read the article

  • No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

    - by jrosell
    Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

    Read the article

  • How to troubleshoot ethernet port on laptop

    - by Psallas Vassilios
    I have a problem with my wired connection. To be more specific, my laptop doesn't seems to recognize that I have plugged in an ethernet cable. I tried to download new drivers for my ethernet card, but I couldn't find any solutions. Maybe because I am new to Linux, so I'm not familiar with running commands in the terminal. OK I have typed the command and here are the results: 00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02) For the second reply I don't know if the following is what you asked me: ?Memory: 3.9 GiB ?Processor: Intel Core 2 Duo CPU P8800 @ 2.66GHz × 2 ?OS type: 32-bit My Ethernet connection had some problem on Windows too. I have changed recently my internet provider, and since then my ethernet cable is not recognized by the laptop. At that time I was still on Windows. I thought that with Ubuntu the problem would be solved, but unfortunately the problem still persists. If someone can help me to solve my problem I'll be thankful. Here are the results of the three first commands you told me to run: lsmod | grep sis190 sis190 22570 0 sudo modprobe sis190 ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:90:81:7e UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:185 errors:0 dropped:0 overruns:0 frame:0 TX packets:185 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22672 (22.6 KB) TX bytes:22672 (22.6 KB) wlan0 Link encap:Ethernet HWaddr 00:25:d3:2c:3a:ae inet addr:192.168.1.72 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::225:d3ff:fe2c:3aae/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:260 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:71992 (71.9 KB) TX bytes:52000 (52.0 KB) and the results of running the last two commands: dmesg | grep -e eth -e sis190 [ 0.816667] sis190: sis190 Gigabit Ethernet driver 1.4 loaded [ 0.816728] sis190 0000:00:04.0: setting latency timer to 64 [ 0.816751] sis190: 0000:00:04.0: Read MAC address from EEPROM [ 0.904032] sis190: 0000:00:04.0: Realtek PHY RTL8201 transceiver at address [ 1.416030] sis190: 0000:00:04.0: Using transceiver at address 1 as default [ 1.448235] sis190 0000:00:04.0: eth0: 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at f8410000 (IRQ: 19), 00:90:f5:90:81:7e [ 1.448238] sis190 0000:00:04.0: eth0: GMII mode. [ 1.448243] sis190 0000:00:04.0: eth0: Enabling Auto-negotiation [ 11.560907] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372019] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372265] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 26.424038] sis190 0000:00:04.0: eth0: auto-negotiating... nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: sis190 State: unavailable Default: no HW Address: 00:90:F5:90:81:7E Capabilities: Carrier Detect: yes Wired Properties Carrier: off

    Read the article

  • Trying to use stencils in 2D while retaining layer depth

    - by Steve
    This is a screen of what's going on just so you can get a frame of reference. http://i935.photobucket.com/albums/ad199/fobwashed/tilefloors.png The problem I'm running into is that my game is slowing down due to the amount of texture swapping I'm doing during my draw call. Since walls, characters, floors, and all objects are on their respective sprite sheet containing those types, per tile draw, the loaded texture is swapping no less than 3 to 5+ times as it cycles and draws the sprites in order to layer properly. Now, I've tried throwing all common objects together into their respective lists, and then using layerDepth drawing them that way which makes things a lot better, but the new problem I'm running into has to do with the way my doors/windows are drawn on walls. Namely, I was using stencils to clear out a block on the walls that are drawn in the shape of the door/window so that when the wall would draw, it would have a door/window sized hole in it. This is the way my draw was set up for walls when I was going tile by tile rather than grouped up common objects. first it would check to see if a door/window was on this wall. If not, it'd skip all the steps and just draw normally. Otherwise end the current spriteBatch Clear the buffers with a transparent color to preserve what was already drawn start a new spritebatch with stencil settings draw the door area end the spriteBatch start a new spritebatch that takes into account the previously set stencil draw the wall which will now be drawn with a hole in it end that spritebatch start a new spritebatch with the normal settings to continue drawing tiles In the tile by tile draw, clearing the depth/stencil buffers didn't matter since I wasn't using any layerDepth to organize what draws on top of what. Now that I'm drawing from lists of common objects rather than tile by tile, it has sped up my draw call considerably but I can't seem to figure out a way to keep the stencil system to mask out the area a door or window will be drawn into a wall. The root of the problem is that when I end a spriteBatch to change the DepthStencilState, it flattens the current RenderTarget and there is no longer any depth sorting for anything drawn further down the line. This means walls always get drawn on top of everything regardless of depth or positioning in the game world and even on top of each other as the stencil has to happen once for every wall that has a door or window. Does anyone know of a way to get around this? To boil it down, I need a way to draw having things sorted by layer depth while also being able to stencil/mask out portions of specific sprites.

    Read the article

  • Routing Internet traffic over specific network interfaces [on hold]

    - by dipamchang
    I want to route my internet traffic over all my available connections (like LAN and Data card(3G)), based on conditions like, if a website is blocked over LAN, that traffic goes through Data Card (or other available internet connection). My ultimate motive is to integrate this feature in my web browser which I have already built using C# and .Net framework. I have found that one can add a route by using the following cmd command - route add DestinationIP mask subnet InterfaceGatewayIP but I am stuck as to how should it be implemented using C#?

    Read the article

  • mount.nfs: access denied by server while mounting (null), can't find any log information

    - by Mark0978
    Two ubuntu servers: 10.0.8.2 is the client, 192.168.20.58 is the server. Between the 2 machines, Ping works, ssh works (in both directions). From 10.0.8.2 showmount -e 192.168.20.58 Export list for 192.168.20.58: /imr/nfsshares/foobar 10.0.8.2 mount.nfs 192.168.20.58:/imr/nfsshares/foobar /var/data/foobar -v mount.nfs: access denied by server while mounting (null) Found several things online, tried them all and still can't find any log information anywhere. On the server: [email protected]:/var/log# cat /etc/hosts.allow sendmail: all ALL: 10.0.8.2 /etc/hosts.deny is all comments How can I get a trail of log statements to figure this out? What does it take to get some logging so I have some idea of WHY it won't mount? On the server: [email protected]# nmap -sR RPC 192.168.20.58 Starting Nmap 5.21 ( http://nmap.org ) at 2012-07-04 21:16 CDT Failed to resolve given hostname/IP: RPC. Note that you can't use '/mask' AND '1-4,7,100-' style IP ranges Nmap scan report for 192.168.20.58 Host is up (0.0000060s latency). Not shown: 988 closed ports PORT STATE SERVICE VERSION 22/tcp open unknown 80/tcp open unknown 111/tcp open unknown 139/tcp open unknown 445/tcp open unknown 902/tcp open unknown 2049/tcp open unknown 3000/tcp open unknown 5666/tcp open unknown 8009/tcp open unknown 8222/tcp open unknown 8333/tcp open unknown Nmap done: 1 IP address (1 host up) scanned in 3.81 seconds From the client: [email protected]:~$ nmap -sR RPC 192.168.20.58 Starting Nmap 5.21 ( http://nmap.org ) at 2012-07-04 22:14 EDT Failed to resolve given hostname/IP: RPC. Note that you can't use '/mask' AND '1-4,7,100-' style IP ranges Nmap scan report for 192.168.20.58 Host is up (0.73s latency). Not shown: 988 closed ports PORT STATE SERVICE VERSION 22/tcp open unknown 80/tcp open unknown 111/tcp open rpcbind (rpcbind V2) 2 (rpc #100000) 139/tcp open unknown 445/tcp open unknown 902/tcp open unknown 2049/tcp open nfs (nfs V2-4) 2-4 (rpc #100003) 3000/tcp open unknown 5666/tcp open unknown 8009/tcp open unknown 8222/tcp open unknown 8333/tcp open unknown Nmap done: 1 IP address (1 host up) scanned in 191.56 seconds

    Read the article

  • ICMP Redirect Theory VS. Application

    - by joeqwerty
    I'm trying to watch ICMP redirects in a lab using Cisco Packet Tracer (version 5.3.2) and I'm not seeing them, which leads me to believe that either my lab configuration isn't correct or my understanding of ICMP redirects isn't correct or that Packet Tracer doesn't support/use ICMP redirects. Here's what I believe to be true regarding ICMP redirects: Routers send ICMP redirects when all of these conditions are met: The interface on which the packet comes into the router is the same interface on which the packet gets routed out. The subnet or network of the source IP address is on the same subnet or network of the next-hop IP address of the routed packet. The datagram is not source-routed. The router kernel is configured to send redirects. I have the lab set up in Cisco Packet Tracer as displayed in the image and would expect to see an ICMP redirect from Router1 when pinging from PC1 to PC3. I'm not seeing the ICMP redirect and it looks like Router1 is actually routing all of the packets via Router2. I have IP ICMP debugging enabled on Router1 (and Router2) and I'm not seeing any ICMP redirect activity in either console. I'm also not seeing a route to the PC3 network in the routing table on PC1, which I think confirms that the ICMP redirect is not occurring. I'm using only static routing on Routers 1 and 2. Is my understanding of ICMP redirects incorrect, or is there a problem with my lab configuration or does Packet Tracer not support/use ICMP redirects?

    Read the article

  • Modify registry for Internet Connection Sharing?

    - by Tim
    My OS is Windows XP. Quoted from How to Change the IP Range for the Internet Connection Sharing DHCP service Use Registry Editor to modify the data value of the IntranetInfo value in the following registry key: Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing\Settings\General The first number listed is the IP address of the internal IP address of the Connection Sharing host. The second number is the subnet IP address separated by a comma. Enter the first IP address of the new range followed by the subnet mask, separated by a comma. (For example, 169.254.0.1,255.255.0.0.). Modify the data value of the Start value in the following registry key: Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing\Addressing\Settings Change the value to the second address of the selected IP range. This address cannot be the same or a lower value than the IP address used for the IntranetInfo key. Modify the data value for the Stop value in the same registry key. Enter the last the IP address of the selected IP range. My registry table does not have Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing, and I don't know how to do with my registry table following the above three steps. Can someone guide me through it step by step?

    Read the article

  • best practice to removing DC from Site that no longer connects via vpn in another city

    - by dasko
    hi i am looking for a recap of what i have done already to see if i missed anything. i had two cities connected by wan using a ipsec persistent tunnel between gateways. i had one DC (DOMAIN CONTROLLER) in each city that was a global catalog server (GC) they were set up to replicate and i had them configured under Sites and Servers with their own subnet etc... about 6 months ago the one city was removed and i was not able to gracefully remove, through dcpromo, the server that was there. it is no longer used and cannot be brought back. the company went from two sites down to single site. Problem is i had a whole bunch of kcc errors and replication bugs in the event viewer. i wanted to clean up my active directory and decided to use the ntdsutil metadata cleanup commands. i removed the server from the specifed site based on a procedure from petri website. I then removed the instances of the old DC and site from Sites and Servers. Then i went and cleaned up the DNS by removing Host A records, NS server name from both the local DNS forward lookup zone and the _msdcs i also removed the reverse lookup zone for the subnet that no longer exists. is there anything i missed? thanks in advance for any help. gd

    Read the article

  • Windows Server 2008R2 - can't change or remove the default gateway

    - by disserman
    We've installed VMWare Server 2.0 on Windows 2008R2. After some time playing with it (actually only removing host-only and nat networks, and binding adapters to the specified vmnets) we've noticed a strange problem: if you change or remove the default gateway on the network card, the server completely loses a network connection you can't ping it from the subnet, it also can't connect to anyone. When the gateway is removed and a server tries to connect to the other machines, I can see some incoming packets using a sniffer, but I believe they are damaged in some kind (I'm not a mega-guru in TCP/IP and can't find a mistake in a binary translation of the packet) because the other side doesn't respond. What we tried: removed vmware server using add/remove programs deleted everything related to the vmware server and all installed network adapters in the windows registry double checked for the vmware bridged protocol driver file, it's physically absent and no any links in the registry. performed a tcp/ip reset with netsh and disabled/enabled all network adapters in the device manager to recreate a registry keys for them. tried another network adapter. and the situation is the same: as soon you remove or change the default gateway, windows stops working. The total absurd of the situation is that the default gateway points to the non-existing IP. But when it's set, you can ping a server from the subnet, when you remove it - you can't. Any help? I'm starting thinking the new build of the VMWare Server is some kind of the malware... :)

    Read the article

  • Grant access for users on a separate domain to SharePoint

    - by Geo Ego
    Hello. I just completed development of a SharePoint site on a virtual server and am currently in the process of granting users from a different domain to the site. The SharePoint domain is SHAREPOINT, and the domain with the users I want to give access to is COMPANY. I have provided them with a link to the site and added them as users via SharePoint, which is all I thought I would need to do. However, when they go to the link, the site shows them a SharePoint error page. In the security event log, I am showing the following: Event Type: Failure Audit Event Source: Security Event Category: Object Access Event ID: 560 Date: 3/18/2010 Time: 11:11:49 AM User: COMPANY\ThisUser Computer: SHAREPOINT Description: Object Open: Object Server: Security Account Manager Object Type: SAM_ALIAS Object Name: DOMAINS\Account\Aliases\00000404 Handle ID: - Operation ID: {0,1719489} Process ID: 416 Image File Name: C:\WINDOWS\system32\lsass.exe Primary User Name: SHAREPOINT$ Primary Domain: COMPANY Primary Logon ID: (0x0,0x3E7) Client User Name: ThisUser Client Domain: PRINTRON Client Logon ID: (0x0,0x1A3BC2) Accesses: AddMember RemoveMember ListMembers ReadInformation Privileges: - Restricted Sid Count: 0 Access Mask: 0xF Then, four of these in a row: Event Type: Failure Audit Event Source: Security Event Category: Object Access Event ID: 560 Date: 3/18/2010 Time: 11:12:08 AM User: NT AUTHORITY\NETWORK SERVICE Computer: SHAREPOINT Description: Object Open: Object Server: SC Manager Object Type: SERVICE OBJECT Object Name: WinHttpAutoProxySvc Handle ID: - Operation ID: {0,1727132} Process ID: 404 Image File Name: C:\WINDOWS\system32\services.exe Primary User Name: SHAREPOINT$ Primary Domain: COMPANY Primary Logon ID: (0x0,0x3E7) Client User Name: NETWORK SERVICE Client Domain: NT AUTHORITY Client Logon ID: (0x0,0x3E4) Accesses: Query status of service Start the service Query information from service Privileges: - Restricted Sid Count: 0 Access Mask: 0x94 Any ideas what permissions I need to grant to the user to get them access to SharePoint?

    Read the article

  • How do I tell ubuntu to send traffic to a single IP through eth6?

    - by flashnode
    I want to ensure that all IP traffic going to 172.16.60.62 uses eth6. Please provide complete commands because my linux-fu is rusty. The host is running Ubuntu Precise 12.04 user@host:~$ ifconfig eth3 eth3 Link encap:Ethernet HWaddr 00:e0:81:72:fe:c9 inet addr:172.16.60.122 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe72:fec9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:128500 errors:0 dropped:0 overruns:0 frame:0 TX packets:29082 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67524823 (67.5 MB) TX bytes:2217634 (2.2 MB) Interrupt:71 Base address:0x6000 user@host:~$ ifconfig eth6 eth6 Link encap:Ethernet HWaddr 00:60:dd:47:81:35 inet addr:172.16.60.61 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:8135/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:109610 errors:0 dropped:0 overruns:0 frame:0 TX packets:109388 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10785630 (10.7 MB) TX bytes:10754350 (10.7 MB) Interrupt:70 user@host:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.60.1 0.0.0.0 UG 0 0 0 eth3 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth3

    Read the article

  • Limiting bandwidth on internal interface on Linux gateway

    - by Jack Scott
    I am responsible for a Linux-based (it runs Debian) branch office router that takes a single high-speed Internet connection (eth2) and turns it into about 20 internal networks, each with a seperate subnet (192.168.1.0/24 to 192.168.20.0/24) and a seperate VLAN (eth0.101 to eth0.120). I am trying to restrict bandwidth on one of the internal subnets that is consistently chewing up more bandwidth than it should. What is the best way to do this? My first try at this was with wondershaper, which I heard about on SuperUser here. Unfortunately, this is useful for exactly the opposite situation that I have... it's useful on the client side, not on the Internet side. My second attempt was using the script found at http://www.topwebhosts.org/tools/traffic-control.php, which I modified so the active part is: tc qdisc add dev eth0.113 root handle 13: htb default 100 tc class add dev eth0.113 parent 13: classid 13:1 htb rate 3mbps tc class add dev eth0.113 parent 13: classid 13:2 htb rate 3mbps tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip dst 192.168.13.0/24 flowid 13:1 tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip src 192.168.13.0/24 flowid 13:2 What I want this to do is restrict the bandwidth on VLAN 113 (subnet 192.168.13.0/24) to 3mbit up and 3mbit down. Unfortunately, it seems to have no effect at all! I'm very inexperienced with the tc command, so any help getting this working would be appreciated.

    Read the article

  • Why from a virtualized Ubuntu system I can't discover the ip address of my router?

    - by AndreaNobili
    I am not into computer network and I have the following problem finding my router IP address. I have a Windows 8 PC on on which it is installed VmWare Workstation that virtualizes Linux Ubuntu. The network adapter settings of this Virtual Machine is setted as NAT. Now my problem is that if in the Windows 8 DOS shell I perform the ifconfig statment I obtain C:\Users\Andrea>ipconfig Configurazione IP di Windows Scheda Ethernet tap0: Stato supporto. . . . . . . . . . . . : Supporto disconnesso Suffisso DNS specifico per connessione: techub.lan Scheda Ethernet Connessione di rete Bluetooth: Stato supporto. . . . . . . . . . . . : Supporto disconnesso Suffisso DNS specifico per connessione: Scheda LAN wireless Connessione alla rete locale (LAN)* 11: Stato supporto. . . . . . . . . . . . : Supporto disconnesso Suffisso DNS specifico per connessione: Scheda LAN wireless Wi-Fi: Suffisso DNS specifico per connessione: DSL2750B Indirizzo IPv6 locale rispetto al collegamento . : fe80::89ff:6d12:49cf:4354%13 Indirizzo IPv4. . . . . . . . . . . . : 192.168.1.3 Subnet mask . . . . . . . . . . . . . : 255.255.255.0 Gateway predefinito . . . . . . . . . : 192.168.1.1 Scheda Ethernet Ethernet: Stato supporto. . . . . . . . . . . . : Supporto disconnesso Suffisso DNS specifico per connessione: Scheda Ethernet VMware Network Adapter VMnet1: Suffisso DNS specifico per connessione: Indirizzo IPv6 locale rispetto al collegamento . : fe80::edb3:8352:f954:2b0c%23 Indirizzo IPv4. . . . . . . . . . . . : 192.168.129.1 Subnet mask . . . . . . . . . . . . . : 255.255.255.0 Gateway predefinito . . . . . . . . . : Scheda Ethernet VMware Network Adapter VMnet8: Suffisso DNS specifico per connessione: Indirizzo IPv6 locale rispetto al collegamento . : fe80::d00b:8c6e:98b:f1ec%24 Indirizzo IPv4. . . . . . . . . . . . : 192.168.15.1 Subnet mask . . . . . . . . . . . . . : 255.255.255.0 Gateway predefinito . . . . . . . . . : Scheda Tunnel Teredo Tunneling Pseudo-Interface: Stato supporto. . . . . . . . . . . . : Supporto disconnesso Suffisso DNS specifico per connessione: Scheda Tunnel isatap.techub.lan: Stato supporto. . . . . . . . . . . . : Supporto disconnesso Suffisso DNS specifico per connessione: techub.lan Scheda Tunnel isatap.{5B95051D-79AB-4147-92CF-3A2E16698432}: Stato supporto. . . . . . . . . . . . : Supporto disconnesso Suffisso DNS specifico per connessione: Scheda Tunnel isatap.{340A5FAD-1597-402E-B658-29C37E8F7BC2}: Stato supporto. . . . . . . . . . . . : Supporto disconnesso Suffisso DNS specifico per connessione: Scheda Tunnel isatap.DSL2750B: Suffisso DNS specifico per connessione: DSL2750B Indirizzo IPv6 locale rispetto al collegamento . : fe80::5efe:192.168.1.3%26 Gateway predefinito . . . . . . . . . : So, looking at the previous output it appear clear that the default gateway (my router) is: 192.168.1.1, infact if I open it into a browser it apear to me the login mask to enter in the router settings.... Ok, if now I open the virtualized Ubuntu shell and perform the route command I obtain this output: andrea@andrea-virtual-machine:~$ route Tabella di routing IP del kernel Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.15.2 0.0.0.0 UG 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 192.168.15.0 * 255.255.255.0 U 1 0 0 eth0 So, here it say to me that the default gateway is 192.168.15.2 (that is not my router ip address), why? My idea is that it could depend by the NAT. Because my Windows system is connected using the wireless but in the virtualized Ubuntu I see that I am connected to a "wired network". So I think that the NAT virtualize a network adapter (or something like this) and that 192.168.15.2 could be the ip address of this network adapter... But it seems strange to me because, as you can see in the previous ipconfig output the VmWare network adapter addresses are: 192.168.129.1 and 192.168.15.1. So I have also 2 others doubts: 1) What device represents the 192.168.15.2 ip address that the virtualized Ubuntu see as Default gateway but that is not my router? 2) What exactly do the two VmWare network adapter that I have configured into my Windows 8 system? There is a way to discover my router ip from the virtualized Ubuntu system ? Tnx Andrea

    Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >