Search Results

Search found 11904 results on 477 pages for 'non'.

Page 340/477 | < Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >

• Megacli is killing me, any help appreciated

  - by Stefan

  I run a server with 2 drives in raid0 configured through BIOS. I just added 2 more drives using hotplug (the server is dell r610 with RHEL 5.4 64bit) and I would like to configure a separate raid0 partition on these drives. I am getting the following error: /opt/MegaRAID/MegaCli/MegaCli64 -CfgLdAdd r0[32:2, 32:3] -a0 The specified physical disk does not have the appropriate attributes to complete the requested command. Exit Code: 0x26 All the parameters are correct and there is just no reason why this command could not work, see this (fujitsu is current raid, seagate is the new one I want to create): /opt/MegaRAID/MegaCli/MegaCli64 -PDList -aALL | egrep 'Adapter|Enclosure|Slot|Inquiry' Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: 0 Inquiry Data: FUJITSU MBD2147RC D807D0A4PA101174 Enclosure Device ID: 32 Slot Number: 1 Enclosure position: 0 Inquiry Data: FUJITSU MBD2147RC D807D0A4PA10115T Enclosure Device ID: 32 Slot Number: 2 Enclosure position: 0 Inquiry Data: SEAGATE ST9300603SS FS033SE0TF5K Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Inquiry Data: SEAGATE ST9300603SS FS023SE070FK I also tried to set up the drive as hotspare, also some strange error: /opt/MegaRAID/MegaCli/MegaCli64 -PDHSP -Set -physdrv[32:3] -a0 Adapter: 0: Set Physical Drive at EnclId-32 SlotId-3 as Hot Spare Failed. FW error description: The specified device is in a state that doesn't support the requested command. Exit Code: 0x32 As you can see the disk is in Unconfigured, Good state: Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Device Id: 3 Sequence Number: 1 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SAS Raw Size: 279.396 GB [0x22ecb25c Sectors] Non Coerced Size: 278.896 GB [0x22dcb25c Sectors] Coerced Size: 278.875 GB [0x22dc0000 Sectors] Firmware state: Unconfigured(good), Spun Up SAS Address(0): 0x5000c50005cd20b1 SAS Address(1): 0x0 Connected Port Number: 3(path0) Inquiry Data: SEAGATE ST9300603SS FS023SE070FK FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: Foreign Foreign Secure: Drive is not secured by a foreign lock key Device Speed: Unknown Link Speed: Unknown Media Type: Hard Disk Device Drive Temperature :30C (86.00 F)

  Read the article

• Inkscape: what are "line" objects?

  - by Peter Mortensen

  What is a "line" object in Inkscape? Drawing lines in Inkscape is by using the tool "Draw Bezier curves and straight lines (Shift+F6)". This creates objects of another type, "path". Using Inkscape: is there a way to convert an object of type "line" into an object of the more general type "path"? I have imported a drawing (mostly lines, rectangles and text) that has been through Adobe Illustrator: originally made in Inkscape, imported into Illustrator, edited, saved from Illustrator as SVG, imported into Inkscape. Sample from the imported SVG file: <path id="path5855" stroke="#000000" d=" M320.198,275.935" /> <line fill="none" stroke="#000000" x1="348.553" y1="45.097" x2="348.553" y2="185.346" id="line3368" /> Update 1: I have inspected the original XML (SVG) file from 2006 and it does not contain any "line" XML tags. Thus it must be a crime of Adobe Illustrator. When a line is selected in this imported SVG file the bottom panel displays: "Line in root. Click selection to toggle scale/rotation handles.". When a line is selected that was drawn in Inkscape the bottom panel displays: "Path (2 nodes) in Layer 1. Click selection to toggle scale/rotation handles." What is the difference between "line" and "path"? Is "line" some kind of read-only/non-editable object? A generic term like "line" is not easy to use in search, but I have now found the definitions for "line" and "path": SVG line: http://www.w3schools.com/svg/svg_line.asp SVG path: http://www.w3schools.com/svg/svg_path.asp Platform: Inkscape v0.46 (2008-03-10), Windows XP 64 bit, 8 GB RAM.

  Read the article

• Bypassing Router's DNS Settings

  - by Ramon Marco Navarro

  Is there a way to bypass my ISP provided CPE/router's DNS settings? I'd like to use OpenDNS but I am unable to access the administrator acount of the CPE. I tried logging in using the default passwords (admin/admin, admin/1234, etc) to no avail. I found out later that the admin password is generated using a generator where you input the CPE's MAC address. I tried emailing the manufacturer of the CPE (Huawei, the CPE is Huawei BM625) and my ISP but they aren't replying. I also saw similar queries (lots of them!) at Huawei's forums, without a single reply. So as a last resort, I'd like to know a way to bypass the CPE's DNS settings. My subscription is for a WiMAX service. I'm using Windows 7 and have already set the DNS settings for the Local Area Connection. But I still am not seeing the "You are already using OpenDNS" text at OpenDNS's site. And when explicitly using the OpenDNS servers I still seem to get 208.69.38.150 rather than the expected 208.69.38.160: nslookup www.opendns.com. 208.67.222.222 Server: resolver1.opendns.com Address: 208.67.222.222 Non-authoritative answer: Name: www.opendns.com Address: 208.69.38.150

  Read the article

• Disable raid member check upon mount to mount damaged nvidia raid1 member

  - by Halfgaar

  Hi, A friend of mine destroyed his Nvidia RAID1 array somehow and in trying to fix it, he ended up with a non-working array. Because of the RAID metadata, the actual disk data was stored at an offset from the beginning. I was able to identify this offset with dd and a hexeditor and then I used losetup to create a loop device with the proper offset, so that I could mount the partition. It was then that I ran into problems, namely that mount says: "mount: unknown filesystem type 'nvidia_raid_member'". I also had this when trying to mount a Linux MD component the other day, and because I can remember that doing that in the past worked, I surmised that it may be some kind of protection. I therefore booted an old Sysrescue CD and tried it there, which worked (because of the older version of mount/libc/kernel/whatever). I still need to try to get more data, and because I don't want to keep using that SysrecueCD, I'd like to be able to mount the disk on my normal system. So, my question is: can the check for a disk being a raid member be disabled? I guess I could also zero out blocks that look like the raid block, but I'd rather not... I made an image of the disk with par2 data, so it's revertable, but still...

  Read the article

• Subversion Apache Ubuntu - Remote Access?

  - by Hollowsteps

  Okay, a couple days ago I built a bare bones kit into a machine. I've been running through tutorials to get it to work and right now I've gotten as far as making it available in my lan, hooray! However, I cannot access the repositories remotely. Any machine on the lan can easily access it through the hostname or, using 'outbound ip/hostname' or 'outbound ip/machine ip'. The machine can be pinged from a remote, non-lan machine and responds. I just can't get anyone into it outside of my lan. I've been trying to figure it out but I'm lost. I'm breaking a few rules and if any of these would be my problem, please indicate. I don't think I have a static IP (However I check my outbound IP whenever I do testing, is that not enough? It has stayed the same for 5+ days) I have not discussed this set-up with my service provider (Does Optimum Online block port 80? If so, can I just switch apache to listen on a different port?) I am in the DMZ of my router. This is what allowed it to be pinged remotely. For security reasons the machine that is in that zone is turned off most of the time until I can get it locked down. Any help would be appreciated, even if it's just a couple of words I could google to understand what I'm doing wrong. Tortoise SVN does not allow access remotely, but it does within the LAN as well.

  Read the article

• Why is my Current Printer unavailable in Office ?

  - by cros

  Whenever I try to print any document from Microsoft Office 2007 in Windows Vista 64-bit there is a great possibility that the print job will fail with the following error message: Current printer is unavailable. Select another printer. Only problem is no printer works, not even Bullzip PDF Printer. The only way to resolve this that I have found so far is a reboot, but I don't want to do that all the time. I am using Windows Vista 64-bit. I've had the problem using both SP1 and SP2. The problem occurs on both locally installed and network printers, as well as the virtual printer Bullzip PDF Printer. My primary source of the problem has been Excel, but the error has also occurred in Word. Changing the default printer and restarting the Microsoft Office-application solves this temporarily, but not permanently. Google:ing the error message returns a lot of questions but no solutions, so seems like a frequent problem. What could be a permanent solution for this problem? UPDATE: It seems that my problem stems from me opening MS Office applications by opening a document from Total Commander with administrative rights. This somehow makes the applications not find the printers. Opening MS Office applications either from the Start menu or by opening a document in a non-administrator Explorer allows me to print.

  Read the article

• How to actually defragment a JFFS2 filesystem

  - by Julie in Austin

  I have searched all over the Internet, including on a number of StackExchange forums, for a workable method for defragmenting a JFFS2 filesystem and cannot find an answer. The system in question has a 256MB NAND flash part. It is being accessed as a MTD device which is divided into three partitions. The third partition is where the root file system is being stored as a JFFS2 file system. The issue is that writes to the root file system have non-deterministic performance due to the usual issues of the JFFS2 garbage collector deciding to run at the worst possible times. When that happens, the product is hung for some unknown length of time while the garbage collector (and pdflush) run. Changing the file system isn't an option. The solution needs to be something that can run during off-hours that after having been run results in more predictable write performance. Right now I am working on a program that will attempt to force the garbage collector to run, then delete the file with the hope that all of the freed nodes are suddenly more readily available and make writes perform better. Thoughts?

  Read the article

• Looking for USB Network Attached Storage (NAS) Adapter that supports multiple drives, NTFS/FAT32 fil

  - by braveterry

  I'm looking for a NAS Adapter that supports attaching multiple USB devices to the network. Here's what I'd like to see in a NAS adapter: Under $100.00. Support for multiple devices. This can be through a USB hub or through multiple USB connectors on the device itself. Bittorrent support would be nice, but this isn't a deal-breaker. Filesystem support for at least NTFS or FAT32. I'd prefer to not have to reformat to use the device, but this is also not a deal-breaker. Here is what I am NOT looking for: I'm NOT looking for a NAS enclosure. I already have a couple of spare external USB drives that I'd like to use. I'm NOT looking for a networked USB hub like the one mentioned here. Network USB hubs only allow access to a drive from one PC at a time. I'm NOT looking for a wireless router with a NAS built in. I already have a wireless router, and I'd rather not go through the hassle of replacing it if possible. What I've looked at so far PogoPlug: This supports multiple devices via a USB hub, but there's not Bittorrent support. It's $99.00, so I may end up going with this and hope that they patch in Bittorrent support later. Addonics NAS Adapter: This supports only one device per adapter, so it's a non-starter. SimpleNET NAS Head USB 2.0 Portable Dongle: I'm not 100% sure this supports multiple devices. Plus there doesn't seem to be any Bittorrent support. I'll try to update this post as I explore other devices.

  Read the article

• Screen scraping software that will traverse pages

  - by nilbus

  We're creating a mashup site that pulls information from many sources all over the web. Many of these sites don't provide RSS feeds or APIs to access the information they provide. This leaves us with screen scraping as our method for collecting the data. There are many scripting tools out there written in different scripting languages for screen scraping that require you to write scraping scripts in the language the scraper was written in. Scrapy, scrAPI, and scrubyt are a few written in Ruby and Python. There are other web-based tools I've seen like Dapper that create XML or RSS feeds based on a webpage. It has a beautiful web-based interface that requires no scripting skills to use. This would be a great tool, if it were able to traverse multiple pages to gather data from hundreds pages of results. We need something that will scrape information from paginated web sites, much like scrubyt, but with a user interface that a non-programmer could use. We'll script up our own solution if we need to, probably using scrubyt, but if there's a better solution out there, we want to use it. Does anything like this exist?

  Read the article

• local msmtp and ovh hosting

  - by klez

  I have my personal email hosted on OVH (personal hosting plan) and I'm not able to send mails using msmtp. Here's a typical session ignoring system configuration file /etc/msmtprc: File o directory non esistente loaded user configuration file /home/klez/.msmtprc using account default from /home/klez/.msmtprc host = ssl0.ovh.net port = 465 timeout = off protocol = smtp domain = localhost auth = choose user = federicoculloca%xxxxxxx password = * ntlmdomain = (not set) tls = on tls_starttls = off tls_trust_file = (not set) tls_crl_file = (not set) tls_fingerprint = (not set) tls_key_file = (not set) tls_cert_file = (not set) tls_certcheck = off tls_force_sslv3 = off tls_min_dh_prime_bits = (not set) tls_priorities = (not set) auto_from = off maildomain = (not set) from = federicoculloca@xxxxxxxx dsn_notify = (not set) dsn_return = (not set) keepbcc = off logfile = (not set) syslog = (not set) reading recipients from the command line TLS certificate information: Owner: Common Name: ssl0.ovh.net Organizational unit: Domain Control Validated Issuer: Common Name: OVH Secure Certification Authority Organization: OVH SAS Organizational unit: Low Assurance Country: FR Validity: Activation time: lun 31 gen 2011 01:00:00 CET Expiration time: mer 15 feb 2012 00:59:59 CET Fingerprints: SHA1: F9:DC:41:F9:A2:38:51:9B:56:E4:98:E6:CD:81:31:42:E6:0E:26:6D MD5: FC:EC:F3:8F:28:E4:7E:28:99:89:E6:BB:C9:DF:71:CE <-- 220 ns0.ovh.net ssl0.ovh.net. You connect to mail427.ha.ovh.net ESMTP --> EHLO localhost <-- 250-ssl0.ovh.net. You connect to mail427.ha.ovh.net <-- 250-AUTH LOGIN PLAIN <-- 250-AUTH=LOGIN PLAIN <-- 250-PIPELINING <-- 250-8BITMIME <-- 250 SIZE 109000000 --> AUTH PLAIN xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx <-- 235 ok, go ahead (#2.0.0) --> MAIL FROM:<federicoculloca@xxxxx> --> RCPT TO:<[email protected]> --> DATA <-- 250 ok <-- 250 ok <-- 354 go ahead --> hello world --> . <-- 554 mail server permanently rejected message (#5.3.0) And my configuration # ~/.msmtp # Mostly from Peter Garrett's examples # https://lists.ubuntu.com/archives/ubuntu-users/2007-September/122698.html # Accounts from Scott Robbins' `A Quick Guide to Mutt' # http://home.nyc.rr.com/computertaijutsu/mutt.html account xxxxx host ssl0.ovh.net from federicoculloca@xxxxxx auth on user federicoculloca%xxxxxx password xxxxxx tls on tls_certcheck off tls_starttls off Any idea?

  Read the article

• Server 2008 R2 Dns Lockup

  - by Richard Maynard

  Hi, We've deployed our first 2008 R2 server on a client site which has replaced their existing 2003 DC. This server provides DNS resolution services to all client machines on that site for general internet usage. Since using the 2008 R2 DNS services we have noticed every couple of days the DNS server starts timing out when requests to certain sites are made (google is the only example I can provide at this time although it seems to be larger sites with problems rather than small - CDN compatiblity issue?). When you restart the DNS Server service then resolution returns to normal... just only for a day or so. Is anybody aware of any significant changes to the DNS server architecture or configuration out of the box in R2 that may explain this intermittent behaviour? I have already tried the fix listed here to no avail: http://weblogs.asp.net/owscott/archive/2009/09/15/windows-server-2008-r2-dns-issues.aspx The following PS command prompt info illustrates the issue: PS C:\Users\Administrator.UK> nslookup Default Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 > www.google.com Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 Non-authoritative answer: Name: www.l.google.com Addresses: 66.102.9.99 66.102.9.104 66.102.9.105 66.102.9.103 66.102.9.147 Aliases: www.google.com > www.google.co.uk Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 * s8209001.uk.kingdomfaith.com can't find www.google.co.uk: Server failed Thanks in advance. Regards,

  Read the article

• Where can I find linux-kernel-headers-x.x.x.x for SUSE?

  - by Landy

  I'm installing VMware Workstation on a SLED 11 SP1, and the installation is blocked by an error message "Kernel headers for version 2.6.32.27-0.2-default were not found". If you installed them in a non-default path you can specify the path below. Otherwise refer to your distribution's documentation for installation instructions and click Refresh to search again in default locations. The output of rpm -qa | grep kernel is kernel-default-2.6.32.27-0.2.2 kernel-default-base-2.6.32.27-0.2.2 linux-kernel-headers-2.6.32-1.4.13 kernel-default-extra-2.6.32.27-0.2.2 nfs-kernel-server-1.2.1-2.10.1 I had met this issue in Ubuntu and I installed the required linux header via apt-get then the issue disappeared. But in SLED, I didn't find the rpm package in SUSE's software repository, and I also google "linux-kernel-headers-2.6.32.27" but did not match any documents. Any suggestion will be highly appreciated. Thanks. The output result of zypper se kernel | grep kernel is i | linux-kernel-headers | Linux Kernel Headers | package | linux-kernel-headers | Linux Kernel Headers | srcpackage

  Read the article

• How to set shmall, shmmax, shmni, etc ... in general and for postgresql

  - by jpic

  I've used the documentation from PostgreSQL to set it for example this config: >>> cat /proc/meminfo MemTotal: 16345480 kB MemFree: 1770128 kB Buffers: 382184 kB Cached: 10432632 kB SwapCached: 0 kB Active: 9228324 kB Inactive: 4621264 kB Active(anon): 7019996 kB Inactive(anon): 548528 kB Active(file): 2208328 kB Inactive(file): 4072736 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 3432 kB Writeback: 0 kB AnonPages: 3034588 kB Mapped: 4243720 kB Shmem: 4533752 kB Slab: 481728 kB SReclaimable: 440712 kB SUnreclaim: 41016 kB KernelStack: 1776 kB PageTables: 39208 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 8172740 kB Committed_AS: 14935216 kB VmallocTotal: 34359738367 kB VmallocUsed: 399340 kB VmallocChunk: 34359334908 kB HardwareCorrupted: 0 kB AnonHugePages: 456704 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 12288 kB DirectMap2M: 16680960 kB >>> ipcs -l ------ Shared Memory Limits -------- max number of segments = 4096 max seg size (kbytes) = 4316816 max total shared memory (kbytes) = 4316816 min seg size (bytes) = 1 ------ Semaphore Limits -------- max number of arrays = 128 max semaphores per array = 250 max semaphores system wide = 32000 max ops per semop call = 32 semaphore max value = 32767 ------ Messages Limits -------- max queues system wide = 31918 max size of message (bytes) = 8192 default max size of queue (bytes) = 16384 sysctl.conf extract: kernel.shmall = 1079204 kernel.shmmax = 4420419584 postgresql.conf non defaults: max_connections = 60 # (change requires restart) shared_buffers = 4GB # min 128kB work_mem = 4MB # min 64kB wal_sync_method = open_sync # the default is the first option checkpoint_segments = 16 # in logfile segments, min 1, 16MB each checkpoint_completion_target = 0.9 # checkpoint target duration, 0.0 - 1.0 effective_cache_size = 6GB Is this appropriate ? If not (or not necessarily), in which case would it be appropriate ? We did note nice performance improvements with this config, how would you improve it ? How should kernel memory management parameters be set ? Can anybody explain how to really set them from the ground up ?

  Read the article

• Dovecot install: what does this error mean?

  - by jamie

  I have postfix and dovecot installed on CentOS 6 (linode) along with MySQL. The table and user is already set up, postfix installed fine, but dovecot gives me this error in the mail log: Warning: Killed with signal 15 (by pid=9415 uid=0 code=kill) The next few lines say this: Apr 7 16:13:35 dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Apr 7 16:13:35 dovecot: config: Warning: NOTE: You can get a new clean config file with: doveconf -n > dovecot-new.conf Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:1: protocols=pop3s is no longer supported. to disable non-ssl pop3, use service pop3-login { inet_listener pop3 { p$ Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:5: ssl_cert_file has been replaced by ssl_cert = <file Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:6: ssl_key_file has been replaced by ssl_key = <file Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:8: namespace private {} has been replaced by namespace { type=private } Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:24: add auth_ prefix to all settings inside auth {} and remove the auth {} section completely Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:25: auth_user has been replaced by service auth { user } I am following directions for the install on CentOS 5 with changes in the dovecot.conf file from different sources specific to CentOS 6. So the dovecot.conf file might not be correct, but there is no good source I have found yet for making dovecot install correctly. Can anyone tell me what the error above means? The terminal does not give any message as to start OK or FAIL. When I issue the service dovecot start command, it says: Starting Dovecot Imap: and nothing more.

  Read the article

• Simple P2V help from Linux to Windows

  - by Ke.

  I have two OS's installed on different drives in my PC. One linux (Centos 5.4) and one windows 7. Its getting tiresome to constantly have to stop and restart the PC when I want to use either OS. I would very much like to use Windows 7 as my host OS and access my linux OS from within Windows. However, im having trouble deciphering exactly how to do this (many of the articles seem confusing and a bit overkill) From what i have seen its possible to use VMWare converter to convert the physical linux image to a virtual image so that I can use it in windows. As im having problems understanding how this is done, I would really appreciate a step by step guide (for a newbie), or any simple tutorials that you can point me at. Some questions beforehand: 1) My linux image is around 80gb, do i need to take this into consideration? The linux drive is around 180gb in total. All my other drives are NTFS non writeable in linux (as I use them in windows and ntfs is dodgy in linux), so probably not possible to move the image over to my ntfs drives 2) Can I just zip the linux files up somehow and transfer it to windows to create the p2v? 3) Is it possible to do the P2V conversion while I am logged into windows. I can see the actual linux drive loaded in disk manager, but windows doesnt read linux file systems so im confused as to how to access the linux drive if this is possible. 4) Or will i need to do the whole p2v conversion inside linux? Cheers, any help is much appreciated Ke (a confused p2v newbie)

  Read the article

• Memcached session manager in Azure: Connection gets forcibly closed

  - by Edgar Pérez

  I am using Memcached Session Manager to handle Tomcat sessions in non-sticky mode. My deployment in Azure consists of a Worker Role with two instances which connect to an Azure VM running my Memcached server. Everything works pretty well, my session is persisted and retrieved by any of the two instances transparently. The problem arises when the session is idle for about 4 minutes; everything points out that the Azure Loadbalancer is closing the spymemcached connection to the VM after some period of inactivity. My MSM configuration is this: <Manager className="de.javakaffee.web.msm.MemcachedBackupSessionManager" memcachedNodes="n1:my-azure-vm.cloudapp.net:11211" sticky="false" sessionBackupAsync="false" sessionBackupTimeout="10000" lockingMode="uriPattern:/path1|/path2" requestUriIgnorePattern=".*\.(ico|png|gif|jpg|css|js|ttf|eot|svg|woff)$" transcoderFactoryClass="de.javakaffee.web.msm.serializer.kryo.KryoTranscoderFactory" customConverter="de.javakaffee.web.msm.serializer.kryo.HibernateCollectionsSerializerFactory"/> The stacktrace printed by the spymemcached client is this: INFO net.spy.memcached.MemcachedConnection: Reconnecting due to exception on {QA sa=/10.194.132.206:13000, #Rops=1, #Wops=0, #iq=0, topRop=net.spy.memcached.protocol.binary.StoreOperationImpl@1d95da8, topWop=null, toWrite=0, interested=1} java.io.IOException: An existing connection was forcibly closed by the remote host at sun.nio.ch.SocketDispatcher.read0(Native Method) at sun.nio.ch.SocketDispatcher.read(Unknown Source) at sun.nio.ch.IOUtil.readIntoNativeBuffer(Unknown Source) at sun.nio.ch.IOUtil.read(Unknown Source) at sun.nio.ch.SocketChannelImpl.read(Unknown Source) at net.spy.memcached.MemcachedConnection.handleReads (MemcachedConnection.java:303) at net.spy.memcached.MemcachedConnection.handleIO (MemcachedConnection.java:264) at net.spy.memcached.MemcachedConnection.handleIO (MemcachedConnection.java:184) at net.spy.memcached.MemcachedClient.run(MemcachedClient.java:1298) Given this idle time limitation in Azure, is there any other way to make MSM work in the azure cloud?

  Read the article

• Apache ProxyPass with SSL

  - by BBonifield

  I have a QA setup that consists of multiple internal development servers and one world-accessible provisioning machine that is setup to proxy pass the web traffic. Everything works fine for non-SSL requests, but I'm having a hard time getting the SSL logic working as well. Here's a few example vhost blocks. <VirtualHost 192.168.168.101:443> ProxyPreserveHost On SSLProxyEngine On ProxyPass / https://192.168.168.111/ ServerName dev1.site.com </VirtualHost> <VirtualHost 192.168.168.101:80> ProxyPreserveHost On ProxyPass / http://192.168.168.111/ ServerName dev1.site.com </VirtualHost> <VirtualHost 192.168.168.101:443> ProxyPreserveHost On SSLProxyEngine On ProxyPass / https://192.168.168.111/ ServerName dev2.site.com </VirtualHost> <VirtualHost 192.168.168.101:80> ProxyPreserveHost On ProxyPass / http://192.168.168.111/ ServerName dev2.site.com </VirtualHost> I end up seeing the following error in the provisioner's error log. [Fri Jan 28 12:50:59 2011] [warn] [client 1.2.3.4] proxy: no HTTP 0.9 request (with no host line) on incoming request and preserve host set forcing hostname to be dev1.site.com for uri / As well as the following entry in the destination QA machine's access log. 192.168.168.101 - - [22/Feb/2011:08:34:56 -0600] "\x16\x03\x01 / HTTP/1.1" 301 326 "-" "-"

  Read the article

• SPF hardfail and DKIM failure when recipient has e-mail forwarding

  - by Beaming Mel-Bin

  I configured hardfail SPF for my domain and DKIM message signing on my SMTP server. Since this is the only SMTP server that should be used for outgoing mail from my domain, I didn't foresee any complications. However, consider the following situation: I sent an e-mail message via my SMTP server to my colleague's university e-mail. The problem is that my colleague forwards his university e-mail to his GMail account. These are the headers of the message after it reaches his GMail mailbox: Received-SPF: fail (google.com: domain of [email protected] does not designate 192.168.128.100 as permitted sender) client-ip=192.168.128.100; Authentication-Results: mx.google.com; spf=hardfail (google.com: domain of [email protected] does not designate 192.168.128.100 as permitted sender) [email protected]; dkim=hardfail (test mode) [email protected] (Headers have been sanitized to protect the domains and IP addresses of the non-Google parties) GMail checks the last SMTP server in the delivery chain against my SPF and DKIM records (rightfully so). Since the last STMP server in the delivery chain was the university's server and not my server, the check results in an SPF hardfail and DKIM failure. Fortunately, GMail did not mark the message as spam but I'm concerned that this might cause a problem in the future. Is my implementation of SPF hardfail perhaps too strict? Any other recommendations or potential issues that I should be aware of? Or maybe there is a more ideal configuration for the university's e-mail forwarding procedure? I know that the forwarding server could possibly change the envelope sender but I see that getting messy.

  Read the article

• URL Rewriting on GoDaddy Virtual Server

  - by Aristotle

  I migrated a Kohana2 application from a shared-hosting environment over to a virtual dedicated server. After this migration, I can't seem to get my .htaccess file working again. I apologize up front, but over the years I have never experienced so much frustration with anything else as I do with the dreaded .htaccess file. Presently I have my project installed immediately within a directory in my public folder: /var/html/www/info.php (general information about server) /var/html/www/logo.jpg (some flat file) /var/html/www/somesite.com/[kohana site exists here] So my .htaccess file is within that directory, and has the following contents: # Turn on URL rewriting RewriteEngine On # Installation directory RewriteBase /somesite.com/ # Protect application and system files from being viewed # This is only necessary when these files are inside the webserver document root RewriteRule ^(application|modules|system) - [R=404,L] # Allow any files or directories that exist to be displayed directly RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d # Rewrite all other URLs to index.php/URL RewriteRule .* index.php?kohana_uri=$0 [PT,QSA,L] # Alternativly, if the rewrite rule above does not work try this instead: #RewriteRule .* index.php?kohana_uri=$0 [PT,QSA,L] This doesn't work. The initial controller is loaded, since index.php is called up implicitly when nothing else is in the url. But if I try to load up some other non-default controller, the site fails. If I place the index.php back within the url, the call to other controllers works just fine. I'm really at my wits end, and would appreciate some direction here.

  Read the article

• How to use cyg-wrapper to fork a new tab in win32 gvim

  - by Peter Nore

  I would like to set up an alias in my cygwin .bashrc that translates pathnames unix-to-dos and passes them to windows gvim in a new tab of an existing instance. I am trying to use Luc Hermitte's cyg-wrapper script for running native win32 applications from Cygwin as per this vim tip. Luc's example of how to use his script is: alias vi= 'cyg-wrapper.sh "C:/Progra~1/Edition/vim/vim63/gvim.exe" --binary-opt=-c,--cmd,-T,-t,--servername,--remote-send,--remote-expr' I do not understand this example because most of these vim parameters (-c,--cmd,--servername,--remote-send,--remote-expr, etc) require more information, and I have not found any example of how to supply the additional information to cyg-wrapper.sh. For example, calling C:/Progra~1/Edition/vim/vim63/gvim.exe --servername=GVIM --remote-tab-silent file1 & will open file1 in a new tab of existing (or non existing) instance GVIM, but calling gvim --servername accomplishes nothing on its own. Unfortunately, though, the corresponding cyg-wrapper phrase does not work: cyg-wrapper.sh "C:/Progra~1/Edition/vim/vim63/gvim.exe" --binary-opt=--servername=GVIM,--remote-tab-silent --fork=2 file1 If ran twice, this actually opens up two instances of gvim; it is as if the servername 'GVIM' is being stripped and ignored. How do you supply a servername to gvim --servername or a .vimrc to gvim -u using cyg-wrapper.sh? Furthermore, why is it that programs must be passed to cyg-wrapper.sh in the relatively obscure "mixed form?" For example, if I try cyg-wrapper.sh "/cygdrive/c/path/to/GVimPortable.exe" --binary-opt=--servername=GVIM,--remote-tab-silent --fork=2 I get "Invalid switch - "/cygdrive"." See also: getting-gvim-to-automatically-translate-a-cygwin-path alias-to-open-gvim-cream-version-from-cygwin-shell

  Read the article

• Antivirus Configuration for dedicated SQL and dedicated IIS Servers

  - by Wayne Arthurton

  Our corporate standard is McAfee Enterprise, unfortunately this is non-negotiable. On two types of servers I'm responsible for, SQL & Web, we have noticed major performance issues with the corporate standard setup. Max scan time 45sec One policy for all processes Scan ALL files on write, read and open for backup Heuristics: Find unknown programs, trojans and macros Detect unwanted programs Exclude: EVT, LDF, LOG, MDF, VMD, , windows file protection) This of course still causes major slowdowns. IIS .NET recompiles are slow especially with SharePoint, SQL backups and restores, SQL Analysis Services, Integration Services and temp data from them as well. I have looked from time to time, for some best practices on setting up McAfee of SQL & SQL Analysis Service, SQL Integration Service, Visual Studio, Sharepoint, and .NET web servers in general. How do people setup McAfee enterprise on their corporate serves keeping security intact, but affecting performance as minimally as possible? Has anyone run across white papers on these setups? Obviously some are case by case, but there must be some best practices out there somewhere.

  Read the article

• postfix Mail filters not running behind a controlled enviornment

  - by Ashish

  Hi, I have deployed a postfix server for email receiving. On this I have configured SenderID + SPF milter, by referring to http://www.postfix.org/MILTER_README.html The command that I used is as follows: ./sid-filter -u postfix -p inet:10027@localhost -l Following are my settings in main.cf file: #Milter support for smtpd mail smtpd_milters = inet:localhost:10027, inet:localhost:10028 # Milters for non-SMTP mail. non_smtpd_milters = inet:localhost:10027, inet:localhost:10028 milter_default_action = reject # Postfix . 2.6 #milter_protocol = 6 # 2.3 . Postfix . 2.5 milter_protocol = 2 Now I have this observation: One of the postfix that is setup on AWS CentOS 5.5 is working fine and is able to receive mails on defined mx record. One of the similar postfix(as in step 1) that is setup behind one of the corporate firewalls is not able to receive any mails and is giving following type of error logs: connect from xxxxxx.austin.hp.com[xx.xxx.96.198] May 25 13:20:02 g2t0385g postfix/smtpd[11733]: C11F9B0194: client=xxxxxxx.austin.hp.com[15.217.96.198] May 25 13:20:03 g2t0385g postfix/cleanup[11814]: C11F9B0194: message-id= May 25 13:20:03 g2t0385g postfix/cleanup[11814]: C11F9B0194: milter-reject: END-OF-MESSAGE from xxxxxx.austin.hp.com[xx.xxx.96.198]: 5.7.1 Command rejected; from= to= proto=ESMTP helo= Here the 'sid-filter' is giving problems. Any idea, what I am doing wrong? Please help. Thanks in advance Ashish Sharma

  Read the article

• Redmine subversion won't ignore certificate error even if told

  - by Pekka

  I have set up a copy of Redmine through the Bitnami Redmine Stack and am having trouble accessing a remote SVN repository through https. The trouble seems to be related to the fact that I don't have a signed certificate, and the certificate provided doesn't match the host name (I am accessing the same server through a number of host names). I am new to Ruby, Mongrel, Rails and Redmine. Following the advice in this forum thread, I changed the path Redmine uses to invoke the svn client in \apps\redmine\lib\ redmine\scm\adapters\subversion_adapter.rb from SVN_BIN = "svn" to SVN_BIN = "svn --trust-server-cert --non-interactive --config-dir c:/user/temp" I was hoping that the --trust-server-cert option would fix the certificate problem. However, I am still getting the following error message in mongrel.log: svn: OPTIONS of 'https://server.xyz:8443/svn/reponame': Server certificate verification failed: certificate issued for a different hostname, issuer is not trusted (https://server.xyz:8443) Does anybody know what to do about this? Additional info: I re-started the mongrel service after each change I am sure the configuration change has taken effect because subversion has created a full configuration directory in c:\user\temp I can access the remote repository using command line svn no problem The remote repository runs on a Windows box with VisualSVN

  Read the article

• Issue configuring Oracle database for SSL

  - by Santhosha Kaldambe

  Hello, I want to setup Oracle for SSL communication. I am not using SSL authentication for database user. As first requirement, generated self signed certificate using OpenSSL and added certificate to wallet. The wallet location is specified in server configuration. Created listener and it is starting however it does not provide any service. The default listener (non SSL) is working fine. When I execute LSNRCTL.EXE status SSLLISTENER it gives below output. STATUS of the LISTENER Alias SSLLISTENER Version TNSLSNR for 32-bit Windows: Version 11.1.0.6.0 - Production Start Date 14-NOV-2009 01:47:08 Uptime 16 days 22 hr. 14 min. 3 sec Trace Level off Security ON: Local OS Authentication SNMP OFF Listener Parameter File C:\app\Administrator\product\11.1.0\db_1\network\admin\listener.ora Listener Log File c:\app\administrator\diag\tnslsnr\\ssllistener\alert\log.xml Listening Endpoints Summary... (DESCRIPTION=(ADDRESS=(PROTOCOL=tcps)(HOST=)(PORT =2484))) The listener supports no services The command completed successfully Here is exact content of various files after configuration. 1) File Name: tnsnames.ora ORCL = (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = )(PORT 1521)) ) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orcl) ) ) 2) File Name: sqlnet.ora SSL_VERSION = 0 NAMES.DIRECTORY_PATH= (TNSNAMES, EZCONNECT) sqlnet.authentication_services= (NONE) tcp.validnode_checking = no tcp.invited_nodes=(PS0803.oraebs.com,PS2948,PS5098) SSL_CLIENT_AUTHENTICATION = FALSE WALLET_LOCATION = (SOURCE = (METHOD = FILE) (METHOD_DATA = (DIRECTORY = C:\app\Administrator\admin\orcl\Server_Wallet) ) ) 3) File Name: listener.ora SSL_CLIENT_AUTHENTICATION = FALSE WALLET_LOCATION = (SOURCE = (METHOD = FILE) (METHOD_DATA = (DIRECTORY = C:\app\Administrator\admin\orcl\Server_Wallet) ) ) LISTENER = (DESCRIPTION_LIST = (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521)) ) (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = )(PORT 1521)) ) ) SSLLISTENER = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCPS)(HOST = )(PORT = 2484)) ) Thanks Santhosh

  Read the article

• How do I locate the app generating this network traffic?

  - by Christopher Bartels

  I don't know what this process is doing on my computer. I run Windows 7 Professional w/ all its updates running current non-free antivirus. I only see it in Resource Monitor, where you can see the Network Service process connected to bitum.nnov.ru. When my PC's network traffic generating apps are idle, this process is using the most of all the idle processes using the network. Screenshot hosted here: http://sss.proinbox.com/bitum-nnov-ru.jpg Does anyone recognize this? The page source mentions a control port & a stream port: Page Source for http://bitum.nnov.ru : <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <title>DVR WebViewer</title> <meta http-equiv="Content-Type" content="text/html; charset=euc-kr"> </head> <body topmargin="0" leftmargin="0"> <OBJECT classid="clsid:EE479A40-C128-40DD-93DA-000556AF9607" codebase="CtrWeb.cab#version=1,0,2,2" width=875 height=585 align=center hspace=0 vspace=0 > <param name="CmdPort" value="5920"> <param name="StreamPort" value="5921"> </body> </html> When I google this page's title, I see a number of other domains that host the same page. Whois: domain: NNOV.RU nserver: ns.kis.ru. nserver: ns.nnov.ru. 78.25.80.210 nserver: ns1.kis.ru. nserver: ns2.kis.ru. state: REGISTERED, DELEGATED, VERIFIED org: "Agentstvo Delovoj Svjazi", Ltd registrar: RU-CENTER-REG-RIPN admin-contact: https://www.nic.ru/whois created: 1996.10.23 paid-till: 2012.11.01 free-date: 2012.12.02 source: TCI Last updated on 2012.06.16 04:20:46 MSK

  Read the article

< Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >