Search Results

Search found 17782 results on 712 pages for 'questions and answers'.

Page 341/712 | < Previous Page | 337 338 339 340 341 342 343 344 345 346 347 348  | Next Page >

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Telugu (unicode) font rendering in emacs

  - by Prakash K

  [I asked the following question in stackoverflow, and I have been redirected here. I hope I can get some answers here. My question at stackoverflow had two small images showing the example rendering of text. As a new user at superuser, I am not being allowed to include them here, nor I am allowed to post more than one hyperlink. And, I don't have enough reputation on SO to migrate that question. Please look at the stackoverflow question for the images. Sorry about the inconvenience.] I sometimes edit text in telugu language. However, when I open the file (UTF-8 encoded) in GNU emacs (version 23.1.50.1 on Ubuntu Jaunty) the text rendering is incorrect. The same text file opened in gedit is rendered correctly. Here's a snippet: ????????? ???? ???? ???????? rendred in gedit: Please see the SO question for the image showing telugu text rendering in gedit And, the emacs rendering of the same text: Please see the SO question for the image showing telugu text rendering in emacs Wherever glyphs need to be composited (not sure if it's the right word), emacs (or whatever library it uses) is not doing it right. Is there anyway to fix this? Perhaps tuning some setting in my configuration? Any ideas, please?

  Read the article

• How to create a static IP on Windows Server 2008 R2 so I can access the server remotely

  - by Aesir

  I have just purchased a HP Proliant N40L which I am intending to use as a NAS, learning tool and just in general something to mess around with. As a student via the Microsoft dreamspark program I can get a free copy of Windows Server 2008 R2 which I am using as the OS. So that I can remote to the box from outside of my local network and so that I can stream media from it to my PS3, I have read that I need to create a static IP for the server and use port forwarding to forward to this IP so I can remote in. Is this correct? I am not really sure how to do this and if I need to make these changes on my router configuration, on the OS or both. I am a novice when it comes to networking however most resources for Windows server 2008 R2 seem to assume a fair amount of experience already. I realise that using this particular OS may seem like overkill for what I currently wish to do with it (stream content to other devices and backup) but as I can get a copy for free it seems sensible. Edit: From reading answers posted I feel I should give more information. I have now tried to add a static IP address using my router configuration settings. I have used the getmac command to get the mac address of the server. My ISP is Virgin Media and I have gone to the LAN IP section and I have added an IP address to the DHCP Reservation Lease Info. I can now use remote desktop connection internally to remote to the server (so I am assuming assigning this IP has worked). How do I configure this on the OS as well? I am also unsure on how I would remote to this machine outside of my local network?

  Read the article

• Configuring IE to resolve DNS at the proxy rather than locally.

  - by dankilman

  With the intention of tunneling web traffic through an SSH connection, the following has been done: I've manually configured a PAC file in IE7 in the LAN Settings dialog. I've verified that traffic is routed through my SSH tunnel that is setup for SOCKS5 dynamic port forwarding. I see that IE7 is always trying to resolve the name locally first. What I'm looking for is the ability to have the DNS name resolved at the proxy, rather than locally by the browser. There's a setting in Firefox that specifies DNS remote resolution, and Safari does it automatically. I've verified correct operation for these 2 other browsers. It would be nice if I could get IE to work also. This is for reference so you could understand where does the question originate from. Notice: The question was actually found by the help of google but with no answers available. Considering how it is exactly my question I figured I should just copy/paste over here because I don't think I could describe any better (there is a small introduction though).

  Read the article

• PCs on domain can not resolve external IP addresses using the DC's DNS Server

  - by Ben

  I currently have a domain controller which handles all DHCP and DNS. The DHCP works just fine and the domain controller itself can use the internet with no issues. However, PCs that are part of the domain are not able to use external websites, only internal. Does anyone have any way I can solve this issue? Thank you Server: Windows Server 2008 R2 PC: Win7 Enterprise x64 Edit: (domain controller) C:\Users\bcollyer>nslookup google.com Server: localhost Address: 127.0.0.1 Non-authoritative answer: Name: google.com Addresses: 2a00:1450:4009:809::100e 173.194.41.166 173.194.41.165 173.194.41.169 173.194.41.162 173.194.41.161 173.194.41.160 173.194.41.168 173.194.41.167 173.194.41.164 173.194.41.163 173.194.41.174 Edit 2: C:\Users\bcollyernetstat -rn Interface List 12...30 85 a9 f7 8a 21 ......Atheros AR8161/8165 PCI-E Gigabit Ethernet Control ler (NDIS 6.20) 1...........................Software Loopback Interface 1 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11...00 00 00 00 00 00 00 e0 Microsoft Teredo Tunneling Adapter IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.0.67 172.16.0.202 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.16.0.0 255.255.0.0 On-link 172.16.0.202 276 172.16.0.202 255.255.255.255 On-link 172.16.0.202 276 172.16.255.255 255.255.255.255 On-link 172.16.0.202 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.0.202 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.0.202 276 Persistent Routes: None IPv6 Route Table Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link Persistent Routes: None BTW I have no javascript on the server so can't reply to individual answers... Sorry!

  Read the article

• Juniper NetScreen NS-5GT traffic monitoring

  - by blah

  I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

  Read the article

• How can I remedy the always-on-top window problem?

  - by GateKiller

  Sorry for the vague title but this one is hard to explain so bear with me please. I'm using Windows Vista at work for web development and sometimes when I Click or Alt-Tab to background window, the window will get focus but it will not be brought to the front. In order to bring the window to the front, I have to click on the applications border (when the resize cursor appears) and the window will then jump to the front. I've had this problem for about a year now and it happens at least a dozen times a day, but it doesn't do this all the time - seems random. I hope I have explained the issue fully (and you've understood it) and would appreciate any constructive answers or comments to solve this problem. Example: If I Alt-Tab from Google Chrome to Notepad and this problem randomly occurs, Google Chrome will remain in front of Notepad, however, I will be able to type text into Notepad while the window is behind Google Chrome. Clicking on Notepad's content area will not bring it to the front but clicking it's window border will. Video Exampe http://vimeo.com/19388998 In this video, I clicked from Google Chome to UltraEdit and chrome stayed in font, but as you can see, I can still type in UltraEdit. I'm starting to believe that this could be a bug in Google Chrome so I'll continue to watch if this between other applications.

  Read the article

• Pairing Bluetooth device with PIN fails

  - by Pikaro

  I'm trying to pair my old BlackBerry 8310 to my Linux desktop (up-to-date Debian Sid, 3.15-10.dmz.1-liquorix-amd64) by using blueman and its associated tools. Scanning for the device works equally well for both sides; however, I am unable to pair the two once it comes to entering the PIN. If I scan from my PC, I have two options in blueman-manager regarding my phone: Directly selecting "pair", or selecting "setup". If I select "pair", nothing happens on my desktop, but the phone asks me to enter a PIN; if I do so, it reports that pairing has failed. During that, nothing is logged to the console. Selecting "setup" opens a configuration dialog that allows for entering or generating a PIN. Regardless, I get to a screen that tells me to enter the PIN on the phone, and at the same time, the phone pops up the equivalent dialog. This would be what one would expect to work; but whatever I enter (naturally, the same on both), both devices report that pairing has failed, and blueman-manager logs init_services (/usr/lib/python2.7/dist-packages/blueman/main/Device.py:73) Loading services org.bluez.Error.AuthenticationFailed: Authentication Failed If I instead try to pair from the phone, I cannot see any kind of reaction from my desktop - all I get is the equivalent "pairing failed" message from the BlackBerry after I entered a PIN in the dialog that pops up there. hcitool scan and hciconfig -a work without complaints, but I cannot find a way to try the pairing as a whole on the console since bluez-simple-agent seems to have been discontinued and this recommendation is everywhere on Google. hcitool cc as root opens the PIN dialog on the phone, then fails with "Input/Output error" once I enter it. The user is not permitted to execute this command. I also tried creating /usr/lib/bluetooth/<MAC>/pincodes to manually define a persistent PIN, which seems to have had no effect. The same goes for running the different commands as root, though I'm really confused about the internal structure of the Bluetooth subsystem now: They usually and inconsistently failed with Python or DBUS errors or just showed the same results. The only other Bluetooth device I have around are a pair of Creative speakers. Trying "setup" asks me to enter a key on them, which is impossible. If I try "pair", I'm asked for a PIN as I should, but no pairing takes place, and no errors appear on the console. (It just repeats their name a few times.) Interestingly, I tried that before writing my question, and nothing happened in terms of PIN questions, just like with the BlackBerry, which still shows no change. I don't think I actively changed anything since then. The BlackBerry can pair with and connect to the speakers, and everything goes as one would expect, so the problem is definitely with my desktop. So thus my questions: What is that PIN window generated by, and why does it seem to appear randomly? How can I find out what, exactly, fails after trying to add the speakers, as this may give me a clue? Is there any kind of complete log that concerns itself with Bluetooth? What data can I provide to make this more solvable?

  Read the article

• Recent DDE / file open issue with Office 2007 affecting only a few machines, is a Windows Update to blame?

  - by kafka

  All our workstations run Windows 7 Professional 64 bit. It started with one, then another, then another couple of machines having a problem accessing Word files locally and on the network. This doesn't happen on my machine though. Affected users get the error message 'There was a problem sending the command to the program'. I've Googled for solutions, but none of the answers worked. They suggested deleting certain registry keys; unregistering and reregistering the program for DDE; resetting the way that the shell opens .docx programs etc. each to no avail. As it affects local and network shares I believe the problem lies with the clients, and not the server, and I'm starting to suspect that there could have been a recent Windows Update which has caused this. I've tried comparing the updates on my working machine with an affected machine, but I can't immediately see any major differences. Has anyone else recently encountered this problem? What are the best steps to take to further isolate what could be causing this?

  Read the article

• Mac OS X: Update Python for Shell

  - by Nathan G.

  So, I see similar questions, but none of the answers work for me. I updated Python to 3.1.3 from 2.6.1. Everything works, except: When I type python into Terminal, I get: Python 2.6.1 (r261:67515, Jun 24 2010, 21:47:49) [GCC 4.2.1 (Apple Inc. build 5646)] on darwin Type "help", "copyright", "credits" or "license" for more information. >>> So, how do I change the version of Python that runs in the Shell? I've tried the script that they provide. It adds their directory to my $PATH, but it still doesn't change the version that'd displayed from Terminal. Here's what I get when I echo $PATH: /Library/Frameworks/Python.framework/Versions/3.1/bin:/Library/Frameworks/Python.framework/Versions/3.1/bin:/Library/Frameworks/Python.framework/Versions/3.1/bin:/usr/bin:/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/X11/bin It appears that the script provided has added their directory for every time I ran the script (I tried it a few times, naturally). I'll gives links to caps of what is in the other relevant folders it mentions: /Library/Frameworks/Python.framework/Versions/3.1/bin /usr/local/bin /usr/bin Thakns in advance for any ideas!

  Read the article

• nginx giving 404 when accessing php from alias directory

  - by code90

  I am trying to migrate from apache to nginx. The php sites that I am hosting need to access a shared library which turns out to be an alias directory. Below is the configuration I came up with. html files work fine, but php files giving 404. I have read through and tried most (if not all) of the answers to the similar questions with no any success. Any hint on what might be causing the issue in my case? location /wtlib/ { alias /var/www/shared/wtlib_4/; index index.php; } location ~ /wtlib/.*\.php$ { alias /var/www/shared/wtlib_4/; try_files $uri =404; if ($fastcgi_script_name ~ /wtlib(/.*\.php)$) { set $valid_fastcgi_script_name $1; } fastcgi_pass 127.0.0.1:9013; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/shared/wtlib_4$valid_fastcgi_script_name; fastcgi_param REDIRECT_STATUS 200; include /etc/nginx/fastcgi_params; } Thanks all ! Update: Following seems to be working fine: location /wtlib/ { alias /usr/share/php/wtlib_4/; location ~* .*\.php$ { try_files $uri @php_wtlib; } location ~* \.(html|htm|js|css|png|jpg|jpeg|gif|ico|pdf|zip|rar|air)$ { expires 7d; access_log off; } } location @php_wtlib { if ($fastcgi_script_name ~ /wtlib(/.*\.php)$) { set $valid_fastcgi_script_name $1; } fastcgi_pass $byr_pass; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/php/wtlib_4$valid_fastcgi_script_name; fastcgi_param REDIRECT_STATUS 200; include /etc/nginx/fastcgi_params; }

  Read the article

• virtual machines, dual booting and data disks on SSD

  - by stevemarvell

  This is in planning, so if I've got the strategy wrong, please let me know. There are multiple questions here, but I think they all degenerate to the same answers. The hardware is a laptop with a single SSD. I'm trying to not lose the performance of the SSD. I plan a native dual booting Windows (plus cygwin) and Linux machine which is my BYOD and represents the development environment. I keep the codebase on a shared partition (though sometimes this is an external thunderbolt SSD) which can be natively "mounted" by whichever OS is in operation. I boot into one or the other environments depending on the task in hand. Sometime I have to develop with windows tools, but generally, Linux is my preferred development environment. It would be ideal if I could VM the other OS and run either in either. I'm going to assume, because I've not found a sensible VM based solution, that I have get samba involved to share the code partition between VMs. Is this going to blow my SSD performance in the VM? The client also supplies me with a VM for the target environment, usually linux. This is not often suited to development and is used for testing only. I normally keep two copies of this, one as a sandbox and one which I deploy to using the client's preferred method. I keep these VM snapshots on the shared partition. The latter is interacted with over the network and so has no disk sharing requirements. However, it would be useful for the sandbox to be able to "mount" the code base from the natively running OS. Is this samba or nfs again, depending on the native OS? Am I missing a trick which allows this to all work smoothly with all four environments running at once without loosing the SSD performance?

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• Weird Apache behaviour and with files again

  - by afifio

  Hi and thanks for stopping by. I have read Weird Apache problem with file, I have read Weird Apache problem with file ...and its not the problem Setup single XAMPP installation on Windows, single windows user, 2HD, 1 is a portable USB. All is fine, until I move the xampp to new portable HD Symptom Old php files - works fine, new one doesnt http://127.0.0.1/Ajax/index.php - yay http://127.0.0.1/test2/t.php - display the source code http://127.0.0.1/Ajax/test2/t.php - display the source code http://127.0.0.1/Ajax/t.php - display the source code Extra Info IIS+MS Web Development stuff, .NET4, Asp, etc is being installed and still hast reboot yet. .htaccess also seems doesnt work Apache2 conf file was modified to Averride All and still it doesnt care. One of the directory supposed to treat .htm as php yet got text, created another directory and edit a phpinfo, still another text, browse to phpmyadmin, viola, works fine Suspect Does Apache honour XP security and permission ? If so, this is a single user computer. Does Apache dont like my new hard disk/new place ? Why it doesnt execute the php in new directory but happily execute in old folder ? Thanks for the riddle answers

  Read the article

• Is it okay to use an administrator account for everyday use if UAC is on?

  - by Valentin Radu

  Since I switched to Windows 7 about 3 years ago, and now using Windows 8.1, I have become familiar with the concept of User Account Control and used my PC the following way: a standard account which I use for every day work and the built-in Administrator account activated and used only to elevate processes when they request so, or to ”Run as administrator” applications when I need to. However, recently after reading more about User Account Control, I started wondering if my way of working is good? Or should I use an administrator account for every day work, since an administrator account is not elevated until requested by apps, or until I request so via the ”Run as administrator” option? I am asking this because I read somewhere that the built-in Administrator account is a true administrator, by which I mean UAC doesn't pop up when logged in within it, and I am scared of not having problems when potential malicious software come into scene. I have to mention that I do not use it on a daily basis, just when I need to elevate some apps. I barely log in into it 10 times a year... So, how's better? Thanks for your answers! And Happy New Year, of course! P.S. I asked this a year ago (:P) and I think I should reiterate it: is an administrator account as safe these days as a standard account coupled with the built-in Administrator account when needed?

  Read the article

• Why is it a bad idea to use a customer email as the from address

  - by Crab Bucket

  I've got an application that emails users once they have filled in a form. It uses a [email protected] as a from address. The customer wants it to use the email from the form as the from address which could be anything. I have been told that this is a bad idea due to spoofing/blacklisting and spam. I feel really vague about the exact reason about why this is a bad idea particularly as i've got to try to counsel the client out of this. Can someone explain to me why this is a bad idea. Interestingly the client has used a gmail account as the from address as a demo which not only works fine but has enabled the application to start sending emails (it wouldn't do it before with an email which was [email protected]). Erm - what is going on. I'm told one thing and the opposite works. Sorry - i know this is basic but I could find anything on a google search. Largely I think because I'm having trouble even framing the question. EDIT Thank you everyone - great answers. Interestingly the server sending the email and the mail box that it is going to are both behind the same firewall so the client says they are unconcerned about spam. Oh well.

  Read the article

• How to setup the Mac OS X Terminal so it's *just peachy*?

  - by kch

  Hi all, My Terminal is awesome, has every detail just right (for me anyway), and now I'm setting up a few new macs around here and I have no idea whatsoever how to get their terminals to a pretty state. My user account is rather old, has been migrated over many OS X releases and machines, so my Terminal setup has grown rather organically over the years. What I need is a recipe to start from scratch, so 1) I know what I've done, and 2) I can reproduce it anywhere. Things I'm looking for: Full UTF8 support. Setting LC_*, displaying characters correctly, accepting input… I hear this got much easier in 10.5, maybe it all works out of the box now? Setup of OS X-style keyboard text navigation (option-arrows, etc) How you particularly handle meta-key support? (other than ESC'ing your way around) Other things to help our n00bs get around in the shell, such as: List of useful default key bindings (^A, ^D, etc…) Mac-specific .profile, .inputrc goodness Mac-specific tools such as pbpaste & pbcopy, Open Terminal Here, etc If at all possible, a list of files to copy over to another machine that encompasses all the changes made to tune the Terminal. (dotrc files, plists, etc) And, well, anything else really. Just keep the scope on the Mac OS X Terminal application, rather than general unix setup and tools. I think a collection of incomplete answers would be a good start. Post one or two things you remember having done, we'll vote them up, and after a few days I'll try to compile it all into a summary answer.

  Read the article

• SSD for swap on Ubuntu server

  - by grs

  Currently I am reading SSD reviews and I wonder how much exactly I will benefit if I move the 24 GB swap from 7200rpm HDD to SSD. Does anyone implemented swap space on SSD? Is this generally good idea? On a side note: I read that ext4 has much better performance if the journal is on SSD. Anyone with such a setup? Thanks! Edit: Here I will answer the questions posted: Occasionally, relatively rare I am hitting the swap. I know what the swap is for and that is better to get more RAM. When the server begins to swap its performance degrades (not a surprise). The idea is if I have few memory hungry processes running, to improve the overall system performance at that time, using SSD for swap, instead of slower rotational media. At the end - I want to be able to login faster and check the server state during swapping, instead of waiting on the login prompt. And of what I see SSD is cheaper per GB than RAM. Would I have better server performance during swapping (as rare it is) using SSD compared to HDD? Where 10k or 15k rpm HDDs would rate in this scenario? Thank you all for your quick and prompt answers!

  Read the article

• Looking for an application that scrolls or pans netbook screens running Windows

  - by therobyouknow

  I'm looking for a Windows 7 and XP compatible Windows desktop panning/scrolling tool. This is to solve a problem where some applications for example MSN have settings/preference Windows that are not resizeable. I have a Netbook with a small maximum screen resolution e.g. 1024x600. The fixed non-resizeable windows are too large for this display screen size so I cannot see all of the items on these windows, particularly the OK button to save settings. What I would like is a desktop scrolling/panning tool where if I move my mouse pointer to any edge of the display, it pans to show the region of the too-large-fixed window that I could not see. I use a Samsung N110 and Toshiba NB100 netbooks. I'm looking for: A general program that provides desktop panning/scrolling/expanded resolution to allow all regions of a non-resizeable fixed window Preferably a non-graphics hardware specific program but will accept a solution that works with both the above machines I'm NOT looking for (i.e. unsatisfactory answers others have asked that I've already searched and found): Advice on what programs to use that DON'T have the problem of fixed windows Alternative operating system solutions Plugging in an external monitor with larger resolution - I use this option but I need a solution when one is not available, e.g. while travelling etc Advice about not using small screen netbooks - I enjoy the compact convenience of them Advice about change the dpi settings in the Control Panel Display settings Advice about guesswork with the tab key to move the focus the off-screen item I cannot see Thank you in advance.

  Read the article

• I want to replace a number with successive numbers, starting at 1 and going up.

  - by Pär-Magnus Green

  I'm aware that this is something people can easily program, but I'm not familiar with those things, so I was hoping there was an easier solution. I've edited a large database of questions, including sorting, and ended up getting all the question ID's mixed up. I'm trying to do this in Notepad++, but any other suggestions are welcome. I'm wondering if there's a way to search for a string (ex. "Question[any number]") and replace the numbers with first 1, then 2, et.c. For clarification, this is how one question looks like: TriviaBot_Questions[3]['Question'][63] = "Acronyms: What does WTT stand for?"; TriviaBot_Questions[3]['Answers'][63] = {"Want To Trade"}; TriviaBot_Questions[3]['Category'][63] = 7; TriviaBot_Questions[3]['Points'][63] = 1; TriviaBot_Questions[3]['Hints'][63] = {}; and the next question, as is now, is not followed by 64. It might be 245 or 1029, and regardless of which number it is, I want it replaced with "previous number + 1", basically.

  Read the article

• What can I do to determine the root cause of a Windows server hanging/freezing?

  - by Aaronaught

  We set up a new server here a few weeks ago that I am informally responsible for managing. Almost everything works perfectly except for one thing: Every so often it hangs without warning. To clarify: When I say hangs, I mean completely. None of the services respond and I'm unable to even get onto a local console - the display acts as though there's no VGA signal. One time, the server actually responded to pings, another time I got the "destination host unreachable" response, but most of the time the pings just time out, as one would expect for a hung server. Event logs don't show anything after a reboot. I don't mean that they don't show anything interesting, I mean that they don't show anything at all from before the failure occurs to after the reboot. And there are never any performance problems, strange errors, or other obvious signs of impending doom before it happens. I don't expect any easy answers here. What I'd like to know his I can methodically determine the root cause of this problem, be it a misbehaving service, defective hardware, or something else. Is there any kind of logging I can set up that will help me get to the bottom of this? Any hardware diagnostics or remote monitoring? Anything else I can do to help me discover what's actually happening, or at least be able to eliminate what isn't wrong? Just to reiterate, I really don't want to start speculating about possible causes and take a trial-and-error approach, because it's going to be at least several days at a time before I would have conclusive results. I'm looking for solutions to reliably trace the problem to its source.

  Read the article

• FreeNAS pool configuration - RAID1 + other drives

  - by trnelson

  Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

  Read the article

• Recover windows cached domain password

  - by theguy

  I have a computer from another small organization that works with our school. It was previously joined to another domain from elsewhere. The organization doesn't have an IT person so they didn't think of what they needed to do about the information on the computer before they moved it to our school. The previous user of the computer is no longer with the organization so no information about the password. The computer has information that needs to be accessed and programs so putting the hard drive on another computer and grabbing the information is a no go as I need the computer itself to be working as well. The computer is running Windows Vista Business Edition and is joined to a domain with a cached profile. The admin accounts are disabled by GPO. I've been asked to see if I could recover the password but running ophcrack gave me no hits on the cached profile. I'm not too familiar with password recovery tools that would work on a cached profile from a domain so I'm looking for answers here. Any other suggestions? Preferably something free as we're a small school and an easy to use liveCD solution like ophcrack would be appreciated.

  Read the article

• Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit

  - by Gleeson9

  Pre-note: This is not a problem I am having with Minecraft. All answers I can find seem to be Minecraft issues. Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit. I get this error when I try to do something Java related. I cannot launch a .jar without this error coming up and when I try to install JDK, I get this error. This has been plauging me for a while and I was not able to research an answer so I thought I would ask it myself. EDIT: Windows 7 (x64) Dell Studio Laptop, 4GB RAM, external Radeon HD 6950 Graphics Card. I have tried uninstalling all JVMs and reinstalling but it didn't work, although I cannot remember how thorough I was so I may try again. Here is a list of all the Java related things I have installed (found in the uninstall or change programs window): Java 3D 1.5.1 Java 3D 1.5.1 (x64) Java 3D 1.5.2 Java 6 Update 30 Java 6 Update 30 (64-bit) Java 7 Update 2 Java 7 Update 3 (64-bit) JavaFX 2.0.3 (64-bit) JavaFX 2.0.3 SDK (64-bit)

  Read the article

< Previous Page | 337 338 339 340 341 342 343 344 345 346 347 348  | Next Page >