Search Results

Search found 20448 results on 818 pages for 'ip address'.

Page 343/818 | < Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >

• My VPS host (rosehosting) sold me a domain name, but I can't get it to work

  - by Faisal Vali

  My VPS host (rosehosting) sold me a domain name, but I can’t get it to work. They sent me an email with the following (almost a month ago) DNS Servers (unless you ordered your own DNS servers): ns1.rosehosting.com (216.114.78.148) ns2.rosehosting.com (216.114.78.155) Operating System: Ubuntu 9.04 Domain Name: mytestdomainfv.com Host Name: mytestdomainfv.com IP Address: .... Physical Host Name: Vs####.rosehosting.com When I type in the Physical Host Name or the IP from a remote computer I get connected to my VPS. But when i type 'mytestdomainfv.com' the name is never resolved, and it has been a month now. I thought that they would configure it so that it would, but it seems that they haven't. Does anyone know how I can get 'mytestdomainfv.com' to point to my VPS? I looked at some of the other similar questions, but they talk about forwarding GoDaddy domain names - so I'm not sure if it applies - but then again, it might just be my naivete. Any direction will be greatly appreciated. Thanks! p.s mytestdomainfv.com is not the real domain name

  Read the article

• How to stop my VPS from picking up ARP reqs it is not supposed to?

  - by Charles Stewart

  Machine: Xen-3.0 image running stable Debian Linux 2.6.18, pretty vanilla. My VPS provider asks me to deal with some trouble my image is causing, namely handling IP addresses it is not supposed to: The problem is that your server seems to be configured to use IPs that have not been appointed to you. Your server responds to ARP requests for the IPs 81.171.111.219 and 81.171.111.218. But you are not allowed to use those. Not explicitly, as far as I can tell! At least, nothing under /etc or /var/tmp mentions these IP addresses. But arp -v says something I can't make sense of: Address HWtype HWaddress Flags Mask Iface 81.171.111.1 ether 00:0C:DB:E3:80:00 C eth0 Entries: 1 Skipped: 0 Found: 1 What is it listening to? The possibilities seem to be: It's not my fault: my VPS providers have overlooked something. What might that be? 81.171.111.1 means I'm happy listening in on ARP requests that I shouldn't be: how do I change this? In any case, what does this mean? I'm looking in completely the wrong place for information on what my image is doing. Where should I be looking?

  Read the article

• How can I set up a local nameserver and modify DNS zones on it?

  - by Joe Hopfgartner

  This is a follow up to this question. I am having an issue with a Router that doesn't support hairpinning properly. See the link above for details. Now I want to set up a local DNS server that Hosts in our LAN can use to resolve public Hostnames (usual webbrowsing... ). Additionally I want to modify certain zones. In our LAN we have some servers serving resources that are not available in our public dns zone. We always have to configure our local LMHost files accordingly. For example we have a staging installation with a new feature running on a local Webserver, and we cannot access it with the IP directly because the website runs in a named virtual host container, we have to configure LMHost file to point some domain to the local IP address. And now we have also the Hair pinning issue. So my question is: What software can I use? Will bind do the job? I just need to insert some A entries into the zone. As easy as possible. We have local Linux/Ubuntu servers.

  Read the article

• Apache2 VirtualHost on Debian not working

  - by milo5b

  I am having some problems with Apache2 configuration. I have already tried to look for documentation on the web (Apache's site, Debian's site, here on serverfault, etc), but nothing really helps. I have tried different configurations, but my current configuration is the following (/etc/apache2/sites-available/default): <VirtualHost *:80> ServerAdmin [email protected] ServerName mysite.dev ServerAlias mysite.dev DocumentRoot /var/www/mysite.dev/httpdocs/ ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] ServerName livesite.com ServerAlias www.livesite.com DocumentRoot /var/www/livesite.com/httpdocs/ <Directory /var/www/livesite.com/httpdocs/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> mysite.dev it's just an entry in hosts file on my client machine, while livesite.com it's an actual DNS record which would resolve to the same IP as the IP set in hosts file for mysite.dev. The problem is that when i try to type mysite.dev in my browser, it would automatically go to livesite.com. I tried to have different /etc/apache2/sites-enabled/ files (/etc/apache2/sites-enabled/mysite.dev , /etc/apache2/sites-enabled/livesite.com ) - and of course with the actual sites-available related files, but achieving the same results. I have tried to have a peak on error.log and access.log but there's nothing I can see. My httpd.conf contains: AccessFileName .htaccess And I have no /etc/apache2/conf.d/virtual.conf file. Any help would be greatly appreciated - if I did not provide enough info please let me know I will do my best to provide all necessary info. Thanks

  Read the article

• IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing problem

  - by Ernest Mueller

  Hey all, I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

  Read the article

• Cacti is ignoring hash marks in interface aliases

  - by Matt Simmons

  I'm attempting to set up Cacti to monitor a router's interfaces, and I'm having trouble getting the graph templates to show the information that I'd like. Our interface configuration looks like this: interface GigabitEthernet3/6 description WalljackNumber # Server info no ip address no shutdown switchport switchport access vlan 116 switchport mode access ip dhcp snooping trust spanning-tree portfast The "Server Info" string is really just the machine name, and a short relevant description, such as "PolarSprings vmnic2". The important part appears to be that it follows the hashmark. When I run snmpwalk, I get the proper output: IF-MIB::ifAlias.230 = STRING: WalljackNumber # Server info But in Cacti, when I go into the graph templates and set the title to this: |host_description| - Traffic - |query_ifName| (|query_ifAlias|) All that shows up in the graph is: switchname - Traffic - Gi3/6 (WalljackNumber #) Which strikes me as a little weird. What I suppose MAY be happening is that somewhere in the cacti stream, it's interpreting # as being a comment and stripping everything after, but I'm not sure. I was hoping someone could tell me that this was a known documented behavior, or that I could change it in a setting that I wasn't aware of. The alternative answer is to change the delimiter from # to something else, but I've got over a thousand lit switchports on an old college infrastructure, and I'm not sure what else might be relying on them.

  Read the article

• Using Round Robin DNS on simple VPN setup

  - by dannymcc

  We have two internet connections which are load balanced to share the load between the two. We set this up after one of the internet provider proved to be less than reliable but great speed and latency wise when it is working. We'd rather utilise both connections as much as possible rather than leave one idle until the other drops out. We have a number of remote workers who occasionally need to connect via VPN from their laptops or iPads, we also have a small number of permanent LAN to LAN tunnels running from smaller branches. Originally we only had one internet connection and used one of our static IP addresses for all VPN users. Now that we have two internet connections running all of the time I am trying to make sure that the VPN is available to our team regardless of which connection drops. So my solution is to create two A records for our domain name with a value of vpn. and the two static IP addresses from each peer. Is this a sensible way of achieving this? Should I expect higher latency due to packets being lost if one peer fails and some packets still get routed to it anyway? A brief mockup of the setup I have:

  Read the article

• Successful login with iscsiadm on target still doesn't create block device

  - by Halfgaar

  I've set up an experiment to test iscsitarget and initiator, which at some point worked. Later, I turned the setup back on and much to my dismay, the initiator machine stopped making block devices for its successful logins. As far as I know, I haven't changed anything on either machine. Some details: # iscsiadm -m node --login Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260] Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260] Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260]: successful Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260]: successful Sessions: # iscsiadm -m session tcp: [3] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun1 tcp: [4] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun2 Netstat: # netstat -n -p|grep 3260 tcp 0 0 10.0.0.2:48719 10.0.0.1:3260 ESTABLISHED 1078/iscsid tcp 0 0 10.0.0.2:48718 10.0.0.1:3260 ESTABLISHED 1078/iscsid /var/log/syslog doesn't give errors: Jan 27 11:41:49 vmnode001 kernel: [ 378.041749] scsi7 : iSCSI Initiator over TCP/IP Jan 27 11:41:49 vmnode001 kernel: [ 378.044180] scsi8 : iSCSI Initiator over TCP/IP lsscsi doesn't show my devices: [0:0:1:0] cd/dvd TSSTcorp DVD-ROM TS-L333A D100 /dev/sr0 [4:0:0:0] disk ATA Hitachi HUA72105 A74A - [4:0:1:0] disk ATA Hitachi HUA72105 A74A - [4:1:0:0] disk Dell VIRTUAL DISK 1028 /dev/sda And there are no block devices in /dev for it: # ls -1 /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda3 /dev/sda4 I tried loading all scsi kernel modules I could find, but that doesn't seem to be the problem. I reall don't get this; it used to work. I found people with similar problems (here and here) but no solution. Initiator is Debian Sqeeuze (testing), target is Debian Lenny (stable). iscsitarget is 0.4.16+svn162-3.1+lenny1, open-iscsi (initiator) is 2.0.871.3-2squeeze1. Target kernel: 2.6.26-2-amd64, initiator kernel: 2.6.32-5-amd64

  Read the article

• Unable to send mail to hotmail from rackspace cloud

  - by Jo Erlang

  I'm having issue sending mail from postfix on a rackspace cloud instance for my domain. Hotmail says "550 SC-001 (SNT0-MC4-F35) Unfortunately, messages from 198.101.x.x weren't sent. Please contact your Internet service provider since part of their network is on our block list. " Here is the mail log Sep 20 08:02:59 mydomain postfix/smtpd[1810]: disconnect from localhost[127.0.0.1] Sep 20 08:02:59 mydomain postfix/smtp[1814]: 59CFF4B191: to=<[email protected]>, relay=mx3.hotmail.com[65.55.92.184]:25, delay=0.19, delays=0.1/0.01/0.06/0.01, dsn=5.0.0, status=bounced (host mx3.hotmail.com[65.55.92.184] said: 550 SC-001 (SNT0-MC4-F35) Unfortunately, messages from 198.101.x.x weren't sent. Please contact your Internet service provider since part of their network is on our block list. You can also refer your provider to http://mail.live.com/mail/troubleshooting.aspx#errors. (in reply to MAIL FROM command)) Sep 20 08:02:59 mydomain postfix/smtp[1814]: 59CFF4B191: lost connection with mx3.hotmail.com[65.55.92.184] while sending RCPT TO I have implemented rDNS, SPF and DKIM they all are looking fine. I have checked my IP and domain, on most of the spam black lists and it is listed as ok on those, (not listed as spamming IP) What should I try next?

  Read the article

• ISC DHCPD IPv6 for multiple interfaces

  - by Seoman

  I want to assign multiple IPv6 to a server with multiple NIC. As IPv6 RFC defines, each server has a unique DUID that can have one of the 3 formats (LL, LLT or enterprise). And each NIC has an IAID. So a request from NIC1 its the DUID and the IAID of the NIC1 and the request from NIC2 its the same DUID but the IAID its different. The problem is that from a Centos box, when I ask for an IP in 2 different interfaces, I get the same IP. I can't find how to specify host entry based on DUID and the IAID. I see some people generating a unique DUID based on the MAC of the NIC but this is not IPv6 RFC says. What I tried is: host entry1 { host-identifier option dhcp6.client-id 00:01:00:01:19:fc:f8:1c:52:54:00:7e:c9:ec; option dhcp6.ia-na "00:09:40:5d"; fixed-address6 2001:db8:0:1::202; } host entry2 { host-identifier option dhcp6.client-id 00:01:00:01:19:fc:f8:1c:52:54:00:7e:c9:ec; option dhcp6.ia-na "00:7e:c9:ec"; fixed-address6 2001:db8:0:1::201; } This causes a Segmentation Fault in the client (what is scary...). I guess is not the right use for ia-na option but I don't see any other option.

  Read the article

• Linksys wireless router will not hardware reset.

  - by Jack M.

  Hello, all. I'm unable to make my router perform a hardware reset, and I cannot understand why. All was working well, except that my iPhone could not connect to the wireless. I found that the router was only allowing AES encryption on WPA2 Personal mode, so I upgraded the firmware. I updated the firmware to Ver.1.06.1, and everything went screwy. The router is no longer showing up in the WiFi list (as Linksys, or its previous network name). Wiring into the router gives me an IP address from my ISP (24.121.121.XXX). Attempting to do a hardware reset, but the power light never starts flashing and the router does not seem to reboot. My machine wired in is still online with no interruption in WoW. Pulling the power cord to force a reset returns it to the same state. I even went so far as to pull up my previous IP address (from DynDNS) and try to connect to that, but it wont even ping. What I'm trying to find out is: Did the new firmware fry the thing, or is there some way to fix this? Thanks in advance for any help.

  Read the article

• Monitoring multiple sites on a single server using OpsView

  - by Kev

  We have several web servers. On each of these servers there can be ~250 web sites. I need to add a HTTP check for each site on each server. Each site has a reserved host header that we know can always be resolved in the format of: w10000.hostchecks.mycompany.com w10020.hostchecks.mycompany.com w11992.hostchecks.mycompany.com ..and so on.. What I want is for there to be a master ping check on the web server's main IP address and then separate HTTP checks for each of the sites on the server. If the master ping test fails then I want the HTTP tests to cease until the master ping check goes OK. I had a stab at this and tried do the following: Create a parent host that does a ping check on the server's main ip address (e.g. server is named WEB0001). For each of the sites that reside on WEB0001: Create a separate Host with a Primary Hostname of wXXXXX.hostchecks.mycompany.com Make WEB0001 the parent host Add a monitor (HTTP check to a special url that is mapped into each site using a virtual directory: H- $HOSTADDRESS$ -u /__hostcheck/IsAlive.aspx -w 5 -c 10 -p 80 However I find that if I down the parent server (WEB0001) the http checks seem to continue. Am I going about this completely the wrong way?

  Read the article

• Ruckus wireless AP and Dell PowerConnect configuration problems

  - by DanielJay

  We are working on trying to get some Ruckus Access Points to work correctly on our network. Currently our network is as follows: VLAN 10 - Servers VLAN 11 – Computers/DHCP VLAN 12 – Voice VLAN 13 – Guest We use Dell PowerConnect 6248P switches for our switches. Port settings are as follows: ZoneDirector 1100 is plugged into this port. Should be accessing the server VLAN and then allowing all other traffic. interface ethernet 1/g2 classofservice trust ip-dscp description 'Ruckus ZoneDirector 1100' switchport mode general switchport general pvid 10 switchport general allowed vlan add 10 switchport general allowed vlan add 11-13 tagged exit Access point is plugged into this port. The port has to be on VLAN 11 in order to get DHCP. interface ethernet 1/g16 classofservice trust ip-dscp description 'Ruckus - IT' switchport mode general switchport general pvid 11 switchport general allowed vlan add 10-12 switchport general allowed vlan add 13 tagged exit If we tag the traffic from the SSID as VLAN 11 data fails. If we leave the SSID tagged as 1 the data flows correctly. Are there problems with passing tagged traffic to untagged ports? We are looking to see what we can do to get the SSID tagged as 11 instead of 1. Any suggestions?

  Read the article

• Natting trafic from a tunnel to internet

  - by mezgani

  I'm trying to set up a GRE tunnel between a linux box and a router (LAN), and I'm having a few problems which seem to depend to my iptables configuration. Watching with tcpdump on linux box, I can see packets coming with flags GREv0, all i need right know is forwarding this data to internet, found here some trace : iptables -F iptables -X iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -t nat -F iptables -t nat -X iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -t nat -P OUTPUT ACCEPT iptables -t mangle -F iptables -t mangle -X iptables -t mangle -P PREROUTING ACCEPT iptables -t mangle -P OUTPUT ACCEPT iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -o cloud -j ACCEPT iptables -A FORWARD -i cloud -o ppp0 -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE echo "1" /proc/sys/net/ipv4/ip_forward cloud Link encap:UNSPEC HWaddr C4-CE-7A-2E-F2-BF-DD-C0-00-00-00-00-00-00-00-00 inet adr:10.3.3.3 P-t-P:10.3.3.3 Masque:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:124 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:0 (0.0 B) TX bytes:10416 (10.1 KiB) Table de routage IP du noyau Destination Passerelle Genmask Indic MSS Fenêtre irtt Iface 196.206.120.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.3.3.0 0.0.0.0 255.255.255.0 U 0 0 0 cloud 0.0.0.0 196.206.120.1 0.0.0.0 UG 0 0 0 ppp0 root@aldebaran:~# ip route 196.206.120.1 dev ppp0 proto kernel scope link src 196.206.122.46 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.18 10.3.3.0/24 dev cloud scope link default via 196.206.120.1 dev ppp0

  Read the article

• ServerName wildcards in Apache name-based virtual hosts?

  - by Martijn Heemels

  On our LAN I've set up several 'fake' TLDs in the DNS server, with the intention of using them for Apache name-based virtual hosting. I'd like to combine this with mass-virtual-hosting (i.e. VirtualDocumentRoot) on an Ubuntu 10.04 LAMP server. However, I can't get it to select the right vhost! Here is a summary of the Apache config: NameVirtualHost 10.10.0.205 <VirtualHost 10.10.0.205> ServerName *.test VirtualDocumentRoot /var/www/%-3.0.%-2/test/%1/ CustomLog /var/log/apache2/access.log vhost_combined </VirtualHost> <VirtualHost 10.10.0.205> ServerName *.dev VirtualDocumentRoot /var/www/%-3.0.%-2/dev/%1/ CustomLog /var/log/apache2/access.log vhost_combined </VirtualHost> A hostname such as www.domain.com.dev, correctly resolves to 10.10.0.205, but always selects the top vhost, instead of the bottom one, which matches more closely. I was under the impression that Apache would first try to match the ServerName before defaulting to the top vhost for a given IP. What am I doing wrong? Or is this not possible and must I use another IP for each TLD? apachectl -S outputs (trimmed): 10.10.0.205:* is a NameVirtualHost default server *.test port * namevhost *.test port * namevhost *.dev

  Read the article

• Cisco Router - Add a missing MIB file

  - by Jonathan Rioux

  I have a Cisco 881w, and I would like to setup NBAR in my NetFlow Analyzer. But it says that my router misses this MIB in order to allow NFA to poll the router with snmp to get NBAR infos. From the FAQ page of the NetFlow Analyzer website, it responds to my error: Q. I am able to issue the command "ip nbar protocol-discovery" on the router and see the results. But NFA says my router does not support NBAR, Why? A. Earlier version of IOS supports NBAR discovery only on router. So you can very well execute the command "ip nbar protocol-discovery" on the router and see the results. But NBAR Protocol Discovery MIB(CISCO-NBAR-PROTOCOL-DISCOVERY-MIB) support came only on later releases. This is needed for collecting data via SNMP. Please verify that whether your router IOS supports CISCO-NBAR-PROTOCOL-DISCOVERY-MIB. The missing MIB is: CISCO-NBAR-PROTOCOL-DISCOVERY-MIB I found it here: ftp://ftp.cisco.com/pub/mibs/v2/CISCO-NBAR-PROTOCOL-DISCOVERY-MIB.my But how can I add this MIB into the router? The IOS of my router is: c880data-universalk9-mz.151-3.T1.bin

  Read the article

• filter / directing URLs coming onto a network

  - by Jon

  Hi all, I an not sure if this is possible or not but what i would like to do is as follows: I have one IP address (dynamic using zoneedit.com to keep it upto date). I have one webserver running my main site which is an Ubuntu machine running Apache. I also have a windows 2008 server running another site. Just to confuse things I also run part of my Apache site on the windows server, currently using proxypassreverse to get the information from it. So it looks something like this: IP 1.2.3.4 maps to mydomain.com as well as myotherdomain.com All requests that come into port 80 are forwarded to the Apache box and I use Virtualhost settings to proxy the windows sites where needed. so mydomain.com is an Apache site mydomain.com/mywindowssection is the Apache server using proxypassreverse to get part of the site from the Windows server myotherdomain.com uses Apache and proxypassreverse to get the whole site. What I would like to be able to do is forward all http requests that come into my network to one machine that figures out who should be serving that content. so: mydomain.com would go to the Apache machine myotherdomain.com would go the windows machine. I am just in the process of setting up an Astaro gateway (never done this before so taking a while to configure) as my firewall, dns, dhcp etc, don't know if this can handle it. I have the capacity to run a VM on the network if a seperate box would be needed for this process as well. Thanks for any and all feedback. Jon

  Read the article

• Cisco Spam Blocker, Iron Port, Lotus Domino, Integration Help

  - by NickToyota

  Hi serverfault universe, I work for a medium sized (roughly 200 user) company. We are attempting to intagrate our new Cisco Spam Video Blocker (ironport) device into our network so that it acts as an incoming filter then passes it off to our Lotus domino mail server. And also vise versa. The way our network is setup currently has an mx record pointing to our Domino mail SMTP incoming server which is currently setup to be an inbound gateway and filter (using symantec domino mail software). We want to replace the inbound gateway with the ironport. Our company has also invested in a pool of external IP addresses which I believe has been currently assigned to our web, email, servers. What would the proper course of action be to successfully integrate the device be? Mx record change? Replace the domino gateway completely with the ironport? We attempted to set the ironport device to the external IP of what our mx record is pointing to without much success. Any help on proper setup would be greatly appreciated.

  Read the article

• pppd disconnects from 3G, doesn't reconnect, w/ persist set

  - by bytenik

  I am trying to configure pppd to connect to a 3G network (Sprint, in this case) and then stay connected, reconnecting automatically if the remote connection is terminated. I have enabled the persist option. My configuration file is as follows: hide-password noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/cellular" debug /dev/cell 921600 defaultroute noipdefault user " " persist maxfail 0 lcp-echo-failure 10 lcp-echo-interval 60 holdoff 5 However, when the peer disconnects the connection, pppd often waits a long time (substantially more than my holdoff) to reconnect the modem -- if it ever reconnects at all! An example log showing this: May 23 05:17:24 00270e0a8888 pppd[2408]: rcvd [LCP TermReq id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: LCP terminated by peer May 23 05:17:24 00270e0a8888 pppd[2408]: Connect time 60.1 minutes. May 23 05:17:24 00270e0a8888 pppd[2408]: Sent 0 bytes, received 0 bytes. May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down started (pid 2456) May 23 05:17:24 00270e0a8888 pppd[2408]: sent [LCP TermAck id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down finished (pid 2456), status = 0x0 May 23 05:17:24 00270e0a8888 pppd[2408]: Hangup (SIGHUP) May 23 05:17:24 00270e0a8888 pppd[2408]: Modem hangup May 23 05:17:24 00270e0a8888 pppd[2408]: Connection terminated. May 23 05:17:24 00270e0a8888 pppd[2408]: Terminating on signal 15 May 23 05:17:24 00270e0a8888 pppd[2408]: Exit. May 23 06:08:07 00270e0a8888 pppd[2500]: pppd 2.4.5 started by root, uid 0 May 23 06:08:10 00270e0a8888 pppd[2500]: Script /usr/sbin/chat -v -f /etc/chatscripts/cellular finished (pid 2530), status = 0x0 May 23 06:08:10 00270e0a8888 pppd[2500]: Serial connection established. May 23 06:08:10 00270e0a8888 pppd[2500]: using channel 11 The disconnect at the request of the peer occurs at 5:17, but the reconnect didn't happen until 6:08. I had a friend monitoring the server so I'm not certain that this wasn't a manual reconnection. Either way, it either took almost an hour to reconnect or never reconnected. Shouldn't persist + holdoff 5 cause this to automatically reconnect after 5 seconds of the link terminating?

  Read the article

• router only assigns small number of IPs

  - by Liam Coates

  Been having a problem with my router for a while now, might just be because it is really old but here's the problem: If a lot of computers are connected to my home network someone will get disconnected. They are assigned IPs and it seems like at a certain point (and I don't know how many) you either get assigned the same IP as someone else or something else is happening and you get disconnected - until i soft reset it and it works again which takes 30 secs. I'd say my tablet, my PC, my sisters iPad, 2 laptops and a netbook is the most that can be connected at one time so that is 6 but that should be fine. The only way I know this is the problem is because I turned on my tablet and I was online on my PC, got disconnected but my tablet was still connected, this is just after i turned the tablet on so I know my router is having difficulty with IPs, it is like it assigned the same IP to the tablet which then clashed with my desktop and knocked me off. I see that sometimes the following solves it as well so I wrote a batch file with a menu to execute these commands as I have to do it so often. ipconfig /release ipconfig /flushdns ipconfig /renew Any ideas? Or shall I just get a new router as this one is old and maybe can't handle giving out that many IPs? Cheers!

  Read the article

• How can you connect to a SQL Server not on your domain?

  - by scotty2012

  I have a test machine that's not allowed on our domain because we are testing corporately unsupported applications (SQL 2008 and Server 2008). I want to use management studio to connect to the SQL2008 server but can't get it working. I have authentication set to mixed-mode, I've checked 'allow remote connections to this server', but when I try to access it, I get the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 53) Since it says the provider is Named Pipes, I enabled Named Pipes on the server, but still no dice. I've tried connecting to the system name, the IP, the system name\instance and IP\instance, all to no avail. Is what I'm trying to do not possible? Edit: Well, through some basic troubleshooting, I've found that I can't ping the server from my client computer, but I can ping the client computer from the server? They are both plugged into the same switch, and are sitting next to each other. The windows firewall on the server is turned on, is there some specific settings I need to enable? DAH! So it was the firewall blocking me. How can I enable the firewall and still connect?

  Read the article

• Apache showing 500 error during Active Directory LDAP authentication

  - by Tyllyn

  I have Apache (on Windows Server) set up to authenticate one directory through Active Directory. Config settings are as follows: <LocationMatch "/trac/[^/]+/login"> Order deny,allow Allow from all AuthBasicProvider ldap AuthzLDAPAuthoritative Off AuthLDAPURL ldap://<ip-redacted>:3268/cn=Users,OU=MyBusiness,DC=<dc-redacted>,DC=local?sAMAccountName?sub?(objectClass=*) AuthLDAPBindDN trac@<dc-redacted>.local AuthLDAPBindPassword "<password-redacted>" AuthType Basic AuthName "Protected" require valid-user </LocationMatch> Watching, Wireshark, I see the following get sent through when I visit the page: To the AD server: bindRequest(1) "trac@<dc-redacted>.local" simple And from the AD server: bindResponse(1) success I'm assuming this means that the auth was successful... but Apache doesn't think so. It returns a 500 server to me. Apache logs show the following: [Thu Nov 18 16:21:12 2010] [debug] mod_authnz_ldap.c(379): [client 192.168.x.x] [7352] auth_ldap authenticate: using URL ldap://<ip-redacted>:3268/cn=Users,OU=MyBusiness,DC=<dc-redacted>,DC=local?sAMAccountName?sub?(objectClass=*), referer: http://192.168.x.x/trac/Trac/login [Thu Nov 18 16:21:12 2010] [info] [client 192.168.x.x] [7352] auth_ldap authenticate: user authentication failed; URI /trac/Trac/login [ldap_search_ext_s() for user failed][Filter Error], referer: http://192.168.x.x/trac/Trac/login Now, that log file shows a failed auth for a blank user. I am confused. Any idea what I am doing wrong... and how I can get the Apache authentication working? :) Thanks!

  Read the article

• Fail2Ban adds iptable rules but they are not working?

  - by EApubs

  Fail2Ban just blocked my IP for 3 SSH attempts. It added the iptables rule and I can see it using the "sudo iptables -L -n" command. But I can still access the site and login through SSH! What might be the problem? Is it because im using CloudFlare? I have set Nginx to write the real IPs to the access logs instead of the Cloud Flare IP. Isn't it enough? Chain fail2ban-ssh (1 references) target prot opt source destination DROP all -- 119.235.14.8 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 The input chain : Chain INPUT (policy DROP) target prot opt source destination fail2ban-NoAuthFailures tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 fail2ban-nginx-dos tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,8090 fail2ban-postfix tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 25,465 fail2ban-ssh-ddos tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 ufw-before-logging-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-logging-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-reject-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-track-input all -- 0.0.0.0/0 0.0.0.0/0 LOG all -- 0.0.0.0/0 0.0.0.0/0 LOG flags 0 level 4

  Read the article

• Using proxy.pac to access Apache 2 with a hostname?

  - by leeand00

  Note that I do not have a DNS on my network, and that is why I am resorting to using a proxy.pac file. I would like to be able to access my development Apache 2 server using a name instead of an ip without setting up a full blown DNS. I am aware of setting names in the C:\Windows\System32\drivers\etc\hosts file and the /etc/hosts files, however I cannot edit the hosts file on all of the devices that I am testing the site on. I've added a proxy.pac file to my Apache2 server and pointed my browsers settings to it at: http://192.168.2.221/proxyutils/proxy.pac ...where 192.168.2.221 is thehostname's ip address. I set the above URL in Firefox in the following manner: From the menubar selecting "Edit-Preferences" In the resulting "Firefox Preferences" window clicking the "Advanced" tab. Clicking the "Network" tab Clicking the "Settings" button. Selecting the "Automatic proxy configuration URL:" radio button. Entering http://192.168.2.221/proxyutils/proxy.pac and pressing OK. The contents of the proxy.pac file on the Apache server function FindProxyForURL(url, host) { if( dnsDomainIs(host, "thehostname") ) return "PROXY 192.168.2.221:80"; return "DIRECT"; } In Firefox I then access the following URL: http://thehostname/wp-blog/ And instead of the development version of the Wordpress blog I am trying to access I get a URL of http://thehostnamehttp/thehostname/wp-blog/ in my address bar and a 404 Not Found page in the browser window. Looking over proxy.pac, it seems like calling dnsDomainIs shouldn't work considering I don't have a DNS setup on my network, but I've also tried just comparing the host argument with the string "hostname" and it yielded the same result, even after modifying the proxy.pac file and clicking the reload button near the proxy settings. This could also be a Wordpress problem, since I've noticed that directories without Wordpress seem to function perfectly normally. (see cross post here) Is there any way I can modify my configuration so that I can access the site using http://thehostname/wp-blog/ ?

  Read the article

• SSH through standard Belkin router to Asus Tomato router

  - by Luke

  I've set up SSH on the Tomato firmware on an Asus N10, via port 22 with key authentication. I've tested the keys by connecting with putty directly to the router when connected to its network. That works OK. But this router is behind a Belkin (F5D7632-4) router which also acts as modem and when I try to connect through with the (dynamic) public IP it times out. I'm guessing it's something to do with the NAT? My putty settings are taken from various online tutorials, but it's set up for port 22, with the correct key as mentioned. The Belkin router has port forwarding to the Asus (192.168.2.3) for port 22 TCP and UDP set up. It's now tough to see what to do in order to connect to the Asus router with an external IP - if it's even possible. Ideally I would have liked to have only needed to use the Asus router, but as it doesn't act as a modem, I need to connect it to the Belkin to use Tomato's features. Perhaps there's a solution here too? Network: Internet -> Belkin modem/router -> Asus router (Tomato SSH) -> Devices

  Read the article

< Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >