Search Results

Search found 10731 results on 430 pages for 'k day'.

Page 345/430 | < Previous Page | 341 342 343 344 345 346 347 348 349 350 351 352  | Next Page >

• ADSL2+ - High sync-rate, good line attenuation, but low noise margin and slow speeds

  - by Mark Pim

  I've been with my ISP (IdNet) for a few months and have been getting some good speeds, but in the last week the speed has dramatically decreased (from 15 Mbps+ to around 0.2 Mbps). This happens at all times of day, not just peak periods. Obviously I've done all I can to isolate problems my end - only one PC is connected to the router (via ethernet cable) and no other background programs are using the network etc. I've raised the issue with the ISP and they've suggested trying a new ADSL filter to see if that is casuing the problem, but I thought it would also be good to get the opinion of superuser on possible causes or other troubleshooting I can do. Here are the juicy stats :) My router (Netgear DGN1000) reports: Downstream Upstream Connection Speed 17602 kbps 1062 kbps Line Attenuation 17.9 db 8.6 db Noise Margin 6.0 db 6.1 db I used RouterStats and it seems to show those figures stay fairly consistent all the time I ran the BT speedtest and it reported: download speed of 164 kbps, out of a max achievable of 21000 kbps upload speed of 859 kbps, out of 1048 kbps DSL connection rate 17719 kbps down and 1048 kbps up IP Profile of 15000 kbps Is there any more troubleshooting I can do? Does this look like a problem with my equipment / wiring or with BT's line? Any advice would be great :)

  Read the article

• One workstation gets slow access to the server, but others are fast

  - by Mike Hanson

  I've just setup a machine with Windows Server 2008. It hosts various services, like IIS, POP3, SMTP, Music for Squeezeboxes, VNC. All was working well for the first week or so. One day I needed to create a mapped drive on the server, so it could access files on my workstation. Windows indicated that Network Discovery was needed, so I turned it on with the "Home / Office" option (rather than "Public"). This may be coincidence, but since that time I've been having troubles accessing various services from my main workstation (running Windows 7/64): POP3 continued working correctly, but SMTP was delayed or failed entirely. (Telnet took 20 seconds to connect, but Outlook would never send messages.) VNC failed entirely. I reinstalled it on the server, and now it works but feels sluggish. The music web server was extremely delayed and usually failed. I tried reinstalling, and now it takes about 30 seconds to show the page name on the browser tab, and another 30 seconds to display any page contents. Other machines on the local network seem fine, as do machines connected via the Internet. I don't believe I changed anything on my own machine that would cause this. I considered the possibility that my anti-virus was involved, so I uninstalled AVG (commercial version), but that didn't help. I installed Norton 360 after that, and it didn't complain of viruses on my machine, and the delays remained. Because only my machine is affect, I'm tempted to blame it, except that reinstalling software on the server improved the situation, so there is almost certainly something going on with the server too. The firewall has all the necessary ports open, and it works fine for the other workstations (including external machines connected via the Internet), which indicates that it should be OK. Any ideas?

  Read the article

• Windows module installer delaying login, server 2008 R2

  - by Kyle

  We updated our servers this weekend (windows updates), everything went fine except one of our terminal servers now hangs at login with the message, "waiting for windows modules installer." It eventually times out and leaves an event log message that the service has stopped unexpectedly. I have disabled the service and users can now login in a reasonable time frame. However we will need to re-enable the service in order to install further updates. I'm not sure where to start with this one, I'm an entry level admin and my colleagues are on vacation today, thank God this isn't a serious problem. Further details: -It affects all users. -The only third party software on the server is our ERP software and screwdrivers from Tricerat. -The only event log message is that the service has stopped unexpectedly. -The server manager screen does not display any information about roles it just says, "error". -The remote desktop roles all seem to be functioning properly, Remote app works as well as standard RDP. Let me know if there is any further details I can provide, I will be checking this frequently throughout the day.

  Read the article

• Azure Virtual Machines - what fault tolerance do they provide?

  - by Borek

  We are thinking about moving our virtual machines (Hyper-V VHDs) to Windows Azure but I haven't found much about what kind of fault tolerance that infrastructure provides. When I run VHD in Azure, I've got two questions: Is my VHD and all the data in it safe? I think that uploaded VHDs use the "Storage" infrastructure so they should be automatically replicated to multiple disks and geographically distributed but should I still make a full-image backup just to be safe? (Note that of course I will be backing up the actual data inside VMs that I care about; I just want to know if there is a chance greater than 0.0000001% that one day I will receive an email from Microsoft telling me that my VM is gone and that I should create or restore it from scratch). Do I need to worry about other things regarding the availability of my VMs? I mean, when I have an on-premise server I need to worry about the hardware itself, about the host operating system, what would happen if my router failed, if my Hyper-V's C: drive failed etc. Am I right in thinking that with Azure, their infrastructure takes care of all of this? Thanks.

  Read the article

• Client cannot access my IIS7 web server

  - by Soccerwiz

  I have a Windows 2008 web server on running IIS 7 with about 25 websites. One of those sites is an SaaS application that is accessed constantly throughout the day. However, one particular client keeps getting blocked from my server. They will be using the service, and then all of a sudden they cannot access the program, or any other site on the server. The entire office of 4 users is blocked from accessing anything on the web server. A trace route reveals they get all the way to the server before they are blocked. However, they can access a linux server that is a different VM with a different IP on the same physical server. Also, when they are blocked from their office, they can still access the site from their mobile phone or local Starbucks. They can also occasionally reset the router and gain access to the web server again as they are on a dynamic IP address. I checked IIS and allow all IPs to access the server. There is nothing in the logs the says anything about a user being banned. I really have no idea what is causing this? Could it be a virus on their end? I have even moved the SaaS to a completely new server in a different location, and they were working fine for about a month, and then the problem started occurring again. Are there any hidden blacklists in IIS? Or is it a routing issue on their end?

  Read the article

• NGINX: How do I calculate an optimal no. of worker processes and worker connections?

  - by bodacious

  Our web app is running on a Linode 2048 server at the moment (~ 2048 GB of RAM) The MYSQL database is on another linode of it's own so this server is really only handling NGINX and and the Rails application. The application itself uses about 185976 of memory per instance (RSS). Our traffic is < 1000 per day and the pages are mostly cached so there are fewer hits to the rails app itself. My question is - how can I calculate optimal NGINX config settings for my app? Below is the current config: worker_processes 1; # pid of nginx master process pid /var/run/nginx.pid; events { worker_connections 1024; } http { access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; passenger_root /home/user/.rvm/gems/ree-1.8.7-2011.01@URTV/gems/passenger-3.0.3; passenger_ruby /home/user/.rvm/rubies/ree-1.8.7-2011.01/bin/ruby; include mime.types; default_type application/octet-stream; sendfile on; tcp_nopush on; tcp_nodelay on; # gzip settings gzip on; gzip_http_version 1.0; gzip_comp_level 2; gzip_vary on; gzip_proxied any; gzip_types text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; # load extra modules from the vhosts directory include /opt/nginx/vhosts/*.conf; } Any advice would be appreciated! :)

  Read the article

• SBS 2008 - DNS Forwarders timing out.

  - by Moif Murphy

  Hello, We have an SBS 2008 server that keeps losing connection to the internet approx 2-3 times a day. It's a simple setup, BT Business Broadband ADSL to a Wireless Zyxel router to the server. Clients connect via WiFi from their laptops. Plugging ethernet in makes no difference, only a reboot of the router seems to bring everything back again. I'm looking at the forwarders on the DNS properties page and they're timing out when trying to resolve the IPs. Currently there are two IPs in there, 194.72.9.34 which has timed out and 194.72.9.38 which has finally resolved to ns8.bt.net We've been in there and replaced all media, installed a PCI NIC, have changed the router three times. There are no errors in the DNS event logs pertaining to what's going on. We've also been on to BT who are adamant that it's not their end. Could someone shed some light on what could be going on or where else to look in the configuration of the server? Thank you.

  Read the article

• Large scale file replication with an option to "unsubscribe" from a replicated file on a given machine

  - by Alexander Gladysh

  I have a 100+ GB files per day incoming on one machine. (File size is arbitrary and can be adjusted as needed.) I have several other machines that do some work on these files. I need to reliably deliver each incoming file to the worker machines. A worker machine should be able to free its HDD from a file once it is done working with it. It is preferable that a file would be uploaded to the worker only once and then processed in place, and then deleted, without copying somewhere else — to minimize already high HDD load. (Worker itself requires quite a bit of bandwidth.) Please advise a solution that is not based on Java. None of existing replication solutions that I've seen can do the "free HDD from the file once processed" stuff — but maybe I'm missing something... A preferable solution should work with files (from the POV of our business logic code), not require the business logic to connect to some queue or other. (Internally the solution may use whatever technology it needs to — except Java.)

  Read the article

• MysqlTunner and query_cache_size dilemma

  - by wbad

  On a busy mysql server MySQLTuner 1.2.0 always recommends to add query_cache_size no matter how I increase the value (I tried up to 512MB). On the other hand it warns that : Increasing the query_cache size over 128M may reduce performance Here are the last results: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.5.25-1~dotdeb.0-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 6G (Tables: 195) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [!!] Total fragmented tables: 51 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 19h 17m 8s (254M q [1K qps], 5M conn, TX: 139B, RX: 32B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 24.2G global + 92.2M per thread (1200 max threads) [!!] Maximum possible memory usage: 132.2G (139% of installed RAM) [OK] Slow queries: 0% (2K/254M) [OK] Highest usage of available connections: 32% (391/1200) [OK] Key buffer size / total MyISAM indexes: 128.0M/92.0K [OK] Key buffer hit rate: 100.0% (8B cached / 0 reads) [OK] Query cache efficiency: 79.9% (181M cached / 226M selects) [!!] Query cache prunes per day: 1033203 [OK] Sorts requiring temporary tables: 0% (341 temp sorts / 4M sorts) [OK] Temporary tables created on disk: 14% (760K on disk / 5M total) [OK] Thread cache hit rate: 99% (676 created / 5M connections) [OK] Table cache hit rate: 22% (1K open / 8K opened) [OK] Open file limit used: 0% (49/13K) [OK] Table locks acquired immediately: 99% (64M immediate / 64M locks) [OK] InnoDB data size / buffer pool: 6.1G/19.5G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 192M) [see warning above] The server has 76GB ram and dual E5-2650. The load is usually below 2. I appreciate your hints to interpret the recommendation and optimize the database configs.

  Read the article

• BackupExec 12 + RALUS - VERY slow backups

  - by LVDave

  We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

  Read the article

• Cannot get at data in my NAS

  - by Ben

  I've got a bit of an issue that I'm hoping you can help me with. I have an Iomega ix4 as my NAS. This runs Linux and each drive in the box has 2 partitions: one for the OS and RAID info, and the second for the actual data. I had it configured as RAID5. Recently one of the drives failed. At this point all of the data was available, it was just reporting a failed drive. I had a drive of the same capacity (although not the exact same spec) which I swapped in place of the failed drive. It recognised it, and started to rebuild the data protection. So far so good ... or so I thought. The next day, after data protection had finished reconstructing, the NAS was telling me that 4 new drives had been added, and wanted confirmation to overwrite the data. Obviously I declined to do this. I swapped the failed drive back in again, in the hope that it would return to its previous state of the data being accessible, but one failed disk. However it didn't - it still tells me that the NAS has 4 new drives in it. I am hopeful that the actual data is untouched, so what I need to do is get it to rebuild the RAID without touching the data on the disks. I have ssh access, and have run stuff like mdadm --examine to see what I can find. The mdadm.conf file has no entry in the "definitions of existing MD arrays" section. I have not run any actual rebuilding commands as yet, because this is entering an area which I am out of my depth in. Please can someone advise the best way of getting my data? Thanks.

  Read the article

• Onboard Ethernet suddenly stopped working to router

  - by AfterschoolHobbist

  Hey guys, yesterday I have a sudden problem of my Ethernet connection to my router. My computer is a Pendium 4 with Window XP SP3 running on it and it was working fine earlier in the day, but yesterday night was the start of the problem. My computer is unable to ping to the router and to any other website and unable to get internet connection. As beside it was connected to a hub, I directly connected it to the router directly and the same problem occurred, being unable to ping to the router (and connecting to it) and still no internet access. My directly connected to the modem and the problem still persisted. For each connection, I connected it to my computer and my laptop and my laptop was able to connect, while my desktop computer was unable. I wondered if it was a OS issue and ran a live Ubuntu CD to see if Ubuntu was able to connect to the internet, but the issue persisted and I was unable to get internet access. I then set my router's lease time to 1 hour and waited. After 1 hour, the lease for my computer was removed and I hoped this worked, but it didn't work, but something strange is acting up. My desktop computer is still unable to ping to the router or connect to the internet, but for some reason, my router and desktop computer is still able to contact each other by providing a lease of an local ip address. The router record of a lease to my desktop computer, and when I do ipconfig, my desktop also recognize that it has been provided a local ip address. I have concluded that this is a hardware issue and the only solution to fix this is to by a network card adapter, but I am wondering if anyone has any solutions that could explain why this happen, why my mac address is 01-23-45-67-89-ab, and is there any way to fix it without buying a new network card? Thanks in advance.

  Read the article

• Mapped network drive connection timeout

  - by Terix

  I have server "Alpha" and server "Beta". Server Beta has a shared folder, that is mapped on server Alpha as "X:" On server Alpha there is a .vbs script that runs and take some files on local drive and copy them on X: drive. My issue is if no user log on server Alpha for a long time, it seems like the tcp connection underneath the mapped drive has a timeout, and the vbs script fails on the copy of file. As soon I log with remote desktop on Alpha server, the .vbs is successfull on the copy of the files. I have made many tests, using file logs to check what was happening and I found no way to refresh the connection and let the .vbs be able to copy files unattended.. I have always to log with remote desktop on Alpha server to refresh the connection and let the .vbs copy the files without issues. What can I do to avoid to log every time? The .vbs script runs 3 times a day and is very annoying. I do not have control over server Beta so I cannot change anything there, and I am very limited on changes I can do on server Alpha ( I cannot change registry and that sort of things)

  Read the article

• Switch between network configurations via command line in fedora 17

  - by Mike Fairhurst

  I have two different setups I use on my work laptop; one enables synergy over an ethernet ssh tunnel with my work computer on the local network, and the other opens an HTTP tunnel to my work computer from outside the network. When I have wifi enabled at work, my laptop seems to use it by preference. This makes synergy run incredibly slowly. At home I must use wifi. I have scripts that begin my ssh tunnels, add my ssh keys, and starts up other programs like synergy, and close themselves when I shut my laptop. However, every day I have to start out my routine by opening my gnome-control-center and turning on my ethernet. I have tried route add and ifup, none of it works, so I dove into gnome-control-center's source code and found that it enabled the connection by libnm's method nm_client_activate_connection with some libnm specific structs that I am having trouble tracking down. I'm not much of a c programmer, and I'm not familiar with either GTK or libnm. Does anybody know what fedora 17 does with ethernet connections to fully enable them? Or does anybody know what libnm does to fully enable an ethernet connection? Do I have to write a c script to run libnm for me to fully emulate whatever gnome-control-center is trying to do?

  Read the article

• Log connections to program

  - by Zac

  Besides for using iptables to log incoming connections.. Is there a way to log established inbound connections to a service that you don't have the source to (suppose the service doesn't log stuff like this on its own)? What I'm wanting to do is gather some information based on who's connecting to be able to tell things like what times of the day the service is being used the most, where in the world the main user base is, etc. I am aware I can use netstat and just hook it up to a cron script, but that might not be accurate, since the script could only run as frequently as a minute. Here is what I am thinking right now: Write a program that constantly polls netstat, looking for established connections that didn't appear in the previous poll. This idea seems like such a waste of cpu time though, since there may not be a new connection.. Write a wrapper program that accepts inbound connections on whatever port the service runs on, but then I wouldn't know how to pass that connection along to the real service. Edit: Just occurred to me that this question might be better for stackoverflow, though I am not certain. Sorry if this is the wrong place.

  Read the article

• Can a non-redundant RAID5 cause any serious problems (compared to RAID0)?

  - by leemes

  I used to have a three-disc RAID5 (mdadm) in my computer for personal media storage (music, videos, photos, programs, games, ...). It had three discs with 750 GB each, resulting in an array capacity of 1.5 TB. One day (one year ago), I needed one of those discs to install another operating system. I thought, I don't need the redundancy anymore since I backup the most important stuff (personal photos e.g.) on an external disc anyway. So I decided to remove one of the three discs without converting the RAID to RAID0 or even two separate discs, because I had no temporary storage (since one cannot simply convert the RAID5 to RAID0 AFAIK). So now, for about one year, I have a non-redundant RAID5 with 2 of 3 discs running. Sometimes, one of the discs has a defective contact at the power cable or something similar causing the drive to stop working temporarily (I don't know exactly what it is). Since it still works when rebooting the computer and in most cases by calling some mdadm commands, it wasn't that problematic. Note that the data is not very critical, since I still have a backup of the most important stuff. But in the last few weeks, one of the drives fails very frequently (every few hours), so it gets really annoying to manage this. My questions are: Is there any disadvantage (apart from the annoying management) of a non-redundant RAID5 (with one drive less than typical) over a RAID0? If I understand it correctly, both have no redundancy and the same capacity. On a temporary drive failure, I can restart the array in both cases, assuming that the drive itself still works after the failure. Can it happen that the drive contents alter on a drive failure, making the array inconsistent? If so, can I tell mdadm to check the array for failures (without a file system level checking tool)? Since the drive most probably only has a defective contact causing it to fail for a second only, can I tell mdadm to automatically restart the array, so I will not even notice the failure if no application wanted to access the file system during the failure?

  Read the article

• Linux: Encryption of a physical LVM volume doesn't imply encryption of its logical subvolumes?

  - by java.is.for.desktop

  Hello, everyone! I installed OpenSuse one year ago on my notebook. I created all partitions except /boot inside an LVM partition. I enabled encryption for it during setup. The system asked me a password on each boot later. Everything seemed fine... But one day I wanted to cancel the boot process and did it with SysRq REISUB. During entering this combination, the system suddenly continued to boot without any password being entered. I had no /home and no swap, but / was mounted! I checked multiple times, it was inside an "encrypted" physical LVM volume. Later I found out that OpenSuse can't encrypt / at all. There is an option to enable encryption for each logical volume, and indeed it fails for /. Later I tried Fedora. The options during partitioning were misleading by same means. I could enable "encryption" of a physical volume and each logical subvolume. With the exception that Fedora actually allowed to encrypt /. Question: What's the point of setting up "encryption" for a physical LVM volume, when it doesn't imply (real) encryption of its logical subvolumes? Did I get something wrong in this whole concept?

  Read the article

• Scripted redirection for Outlook 2003

  - by John Gardeniers

  We have a staff member in sales who has gone onto a 4 day week (getting ready for retirement), so each Thursday afternoon her email needs to be forwarded to another user and each Friday afternoon it needs to be set back. I'm using the VBS script below to do this, run via the Task Scheduler. Although the script appears to do it's job, based on what I see when I view the user's Exchange settings, Exchange doesn't always recognise that the setting has changed. e.g. Last Thursday the forwarding was a enabled and worked correctly. On Friday the script did it's thing to clear the forwarding but Exchange continued to forward messages all weekend. I found that I can force Exchange to honour the changed setting be merely opening and closing the user's properties in ADUC. Of course I don't want to have to do that. Is there a non-manual way I can have Exchange read and honour the setting? The script (VBS): ' Call this script with the following parameters: ' ' SrcUser - The logon ID of the suer who's account is to be modified ' DstUser - The logon account of the person to who mail is to be forwarded ' Use "reset" to clear the email forwarding SrcUser = WScript.Arguments.Item(0) DstUser = WScript.Arguments.Item(1) SourceUser = SearchDistinguishedName(SrcUser) 'The user login name Set objUser = GetObject("LDAP://" & SourceUser) If DstUser = "reset" then objUser.PutEx 1, "altRecipient", "" Else ForwardTo = SearchDistinguishedName(DstUser)' The contact common name objUser.Put "AltRecipient", ForwardTo End If objUser.SetInfo Public Function SearchDistinguishedName(ByVal vSAN) Dim oRootDSE, oConnection, oCommand, oRecordSet Set oRootDSE = GetObject("LDAP://rootDSE") Set oConnection = CreateObject("ADODB.Connection") oConnection.Open "Provider=ADsDSOObject;" Set oCommand = CreateObject("ADODB.Command") oCommand.ActiveConnection = oConnection oCommand.CommandText = "<LDAP://" & oRootDSE.get("defaultNamingContext") & ">;(&(objectCategory=User)(samAccountName=" & vSAN & "));distinguishedName;subtree" Set oRecordSet = oCommand.Execute On Error Resume Next SearchDistinguishedName = oRecordSet.Fields("DistinguishedName") On Error GoTo 0 oConnection.Close Set oRecordSet = Nothing Set oCommand = Nothing Set oConnection = Nothing Set oRootDSE = Nothing End Function

  Read the article

• What's Keeping My Computer Awake?

  - by phantomdata

  First the question; How do I figure out what is preventing my Windows 7 computer from going into sleep mode? Second; some background... I've been struggling with this for a few days and am utterly perplexed. I setup sleep mode on my Windows 7 PC a few weeks ago, and all was well. The PC would sleep as expected and I was snuggly in knowing that my computer was saving power and some wear and tear on the components (we'll leave the 'is it better to sleep' debate for another thread/day, please don't start it). Well, I noticed the other night that my system stopped ever going to sleep. I set the sleep time down to 1 minute and wandered fully away from the PC (ensuring that no errant mouse or keyboard movements would occur) and the PC never went to sleep. I've also observed this over longer intervals as well, such as overnight. I have sleep mode enabled, of course "multimedia settings - When Sharing Media" is set to allow the computer to sleep. "powercfg -lastwake" show nothing of interest, since it never goes to sleep and can't wake up. "powercfg /requests" shows 3 entries - all "[DRIVER] ?". I assume that 2 of these are my mouse and keyboard - as I've recently used them to run the powercfg command. I'm at a loss for the third though. I've unhooked all USB peripherals save for my keyboard and mouse. Wake on LAN is disabled in my BIOS. I know that you can disable all apps from waking/preventing sleep - but I want the ability to remain for those apps that do legitimately need to keep the system awake. So; does anyone know of a way to figure out what the 3rd phantom "[DRIVER] ?" is in powercfg /requests?

  Read the article

• Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

  - by Jeff

  A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

  Read the article

• I need to take the first three letters of a filename and set it into a text file, in a certain fashion. How can I do this?

  - by JuniorD

  Okay, so I need to take the first three letters of a file from a list of files, and place this into a text file in a certain manner. I will provide examples below. Lets say that I have two file names in the same directory, one called cougar.txt and the other bear.txt. These are in the animals directory. I need to take the first three letters of these words, and transpose them into a text file along with the directory, in the following format: BEA = "animals/bear.txt" COU = "animals/cougar.txt" This should happen with any random thing that might be in the list. I'm fairly new to this sort of coding, so I'm not quite sure which language to use, and I'm learning as I go. This new challenge seems fairly daunting to me, and I would be much appreciated if you guys could help. Also, I'm using Windows 7. Been attempting at this all day, to no avail. Preferably done in batch, but if that is impossible I'm open to recommendations.

  Read the article

• OpenLDAP 2.4.23 - Debian 6.0 - Import schema - Insufficient access (50)

  - by Yosifov

  Good day to everybody. I'm trying to add a new schema inside OpenLDAP. But getting an error: ldap_add: Insufficient access (50) root@ldap:/# ldapadd -c -x -D cn=admin,dc=domain,dc=com -W -f /tmp/test.d/cn\=config/cn\=schema/cn\=\{5\}microsoft.ldif root@ldap:/# cat /tmp/test.d/cn\=config/cn\=schema/cn\=\{5\}microsoft.ldif dn: cn=microsoft,cn=schema,cn=config objectClass: olcSchemaConfig cn: microsoft olcAttributeTypes: {0}( 1.2.840.113556.1.4.302 NAME 'sAMAccountType' DESC 'Fss ssully qualified name of distinguished Java class or interface' SYNTAX 1.3.6. 1.4.1.1466.115.121.1.27 SINGLE-VALUE ) olcAttributeTypes: {1}( 1.2.840.113556.1.4.146 NAME 'objectSid' DESC 'Fssssull y qualified name of distinguished Java class or interfaced' SYNTAX 1.3.6.1.4. 1.1466.115.121.1.40 SINGLE-VALUE ) olcAttributeTypes: {2}( 1.2.840.113556.1.4.221 NAME 'sAMAccountName' DESC 'Fds sssully qualified name of distinguished Java class or interfaced' SYNTAX 1.3. 6.1.4.1.1466.115.121.1.15 SINGLE-VALUE ) olcAttributeTypes: {3}( 1.2.840.113556.1.4.1412 NAME 'primaryGroupToken' SYNTA X 1.3.6.1.4.1.1466.115.121.1.27 SINGLE-VALUE ) olcAttributeTypes: {4}( 1.2.840.113556.1.2.102 NAME 'memberOf' SYNTAX 1.3.6.1. 4.1.1466.115.121.1.12 SINGLE-VALUE ) olcAttributeTypes: {5}( 1.2.840.113556.1.4.98 NAME 'primaryGroupID' SYNTAX 1.3 .6.1.4.1.1466.115.121.1.27 SINGLE-VALUE ) olcObjectClasses: {0}( 1.2.840.113556.1.5.6 NAME 'securityPrincipal' DESC 'Cso ntainer for a Java object' SUP top AUXILIARY MUST ( objectSid $ sAMAccountNam e ) MAY ( primaryGroupToken $ memberOf $ primaryGroupID ) ) I also tried to add the schema by phpldapadmin, but gain the same error. I'm using the admin user which is specified by default from the begging of the slpad installation. How may I add permissions to this user ? Best wishes

  Read the article

• Windows Vista freezes

  - by Kakurady

  Windows Vista (32-bit) would randomly freeze on my computer, usually 15-30 minutes after login but can happen just after login. All applications would stop responding and the hard drive will not make any sound, and after a while, the mouse cursor will also stop moving. I dual-boot Ubuntu, and that still works fine. It started with the computer freezing when loading Team Fortress 2. Alt-Tab and Ctrl-Alt-Del have no effect, and the hard drive does not make any sound. I tried to verify the game data using Steam and that freezes the computer too. So I stupidly reinstalled the game. Now the game doesn't freeze when it starts, but instead the whole computer randomly freezes. This computer is a Dell XPS M1530 with a 320GB (298GiB) drive (WDC WD3200BEVT-7) split 5-ways, with Windows and Linux a partition each, one more for Linux swap space, and another two partitions for Dell diagnostic program and factory image and drivers. There was once where the hard drive would make clicking noises all day, and only stopped when I rebooted the computer. Since then, the BIOS diagnostics would fail the drive (for "self-test log contains previous errors") whenever ran. (The on-disk diagnostics cannot be run because I overwrote the MBR with GRUB.) Naturally, I thought the hard drive could be the problem. CHKDSK found one bad sector, but this seems to have no effect. System File Checker found two protected files with wrong hashes, one is some kind of IE manifest, and the other is a tcpmon.ini. Neither of them can be restored because their back up copy also have wrong hashes. Nothing about system failures in the event viewer. What should I do next?

  Read the article

• What are the typical methods used to scale up/out email storage servers?

  - by nareshov

  Hi, What I've tried: I have two email storage architectures. Old and new. Old: courier-imapds on several (18+) 1TB-storage servers. If one of them show signs of running out of disk space, we migrate a few email accounts to another server. the servers don't have replicas. no backups either. New: dovecot2 on a single huge server with 16TB (SATA) storage and a few SSDs we store fresh mails on the SSDs and run a doveadm purge to move mails older than a day to the SATA disks there is an identical server which has a max-15min-old rsync backup from the primary server higher-ups/management wanted to pack in as much storage as possible per server in order to minimise the cost of SSDs per server the rsync'ing is done because GlusterFS wasn't replicating well under that high small/random-IO. scaling out was expected to be done with provisioning another pair of such huge servers on facing disk-crunch issues like in the old architecture, manual moving of email accounts would be done. Concerns/doubts: I'm not convinced with the synchronously-replicated filesystem idea works well for heavy random/small-IO. GlusterFS isn't working for us yet, I'm not sure if there's another filesystem out there for this use case. The idea was to keep identical pairs and use DNS round-robin for email delivery and IMAP/POP3 access. And if one the servers went down for whatever reasons (planned/unplanned), we'd move the IP to the other server in the pair. In filesystems like Lustre, I get the advantage of a single namespace whereby I do not have to worry about manually migrating accounts around and updating MAILHOME paths and other metadata/data. Questions: What are the typical methods used to scale up/out with the traditional software (courier-imapd / dovecot)? Do traditional software that store on a locally mounted filesystem pose a roadblock to scale out with minimal "problems"? Does one have to re-write (parts of) these to work with an object-storage of some sort - such as OpenStack object storage?

  Read the article

• Laptop freezing every few seconds, including screen + sound

  - by zenstealth

  Just a few days ago, my Windows 7 HP dv4170us (1.76Ghz CPU, 1GB Ram) laptop started to freeze every other second where everything on screen and and sound (such as a song playing in iTunes) would just freeze until I bash it violently (without actually breaking the laptop) or wait for a couple of more seconds. I think it started one night when I noticed that a USB mouse of mine stopped working, and it displayed random "Device was not recognized" errors. I just unplugged the mouse and ignored it. Skip forward to the next day, is started freezing, and as of today I can't get my computer to not keep freezing. I tried to backup my files onto an external hdd, but it almost corrupted the drive. I ran 4 complete virus scans using MSSE and MalwareBytes (both quick and full scans), and they all came up clean. In the Task manager, the CPU usage is on a constant max, and so is the RAM (if I have just a few apps running, I only have like 30Mb of free RAM left). Also, on the outside of my laptop, right above where the CPU is located, it's very, very hot. I suspect that something is wrong internally within inside of the computer, but I'm not sure. It also does the same thing when booted into Ubuntu.Does anyone know what could be wrong with it?

  Read the article

< Previous Page | 341 342 343 344 345 346 347 348 349 350 351 352  | Next Page >