Search Results

Search found 9611 results on 385 pages for 'low power'.

Page 346/385 | < Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >

• Proxy / Squid 2.7 / Debian Wheezy 6.7 / lots of TCP Timed-out

  - by Maroon Ibrahim

  i'm facing a lot of TCP timed-out on a busy cache server and here below my sysctl.conf configuration as well as an output of "netstat -st" Kernel 3.2.0-4-amd64 #1 SMP Debian 3.2.57-3 x86_64 GNU/Linux Any advice or help would be highly appreciated #################### Sysctl.conf cat /etc/sysctl.conf net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 1 fs.file-max = 65536 net.ipv4.tcp_low_latency = 1 net.core.wmem_max = 8388608 net.core.rmem_max = 8388608 net.ipv4.ip_local_port_range = 1024 65000 fs.aio-max-nr = 131072 net.ipv4.tcp_fin_timeout = 10 net.ipv4.tcp_keepalive_time = 60 net.ipv4.tcp_keepalive_intvl = 10 net.ipv4.tcp_keepalive_probes = 3 kernel.threads-max = 131072 kernel.msgmax = 32768 kernel.msgmni = 64 kernel.msgmnb = 65536 kernel.shmmax = 68719476736 kernel.shmall = 4294967296 net.ipv4.ip_forward = 1 net.ipv4.tcp_timestamps = 0 net.ipv4.conf.all.accept_redirects = 0 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_sack = 0 net.ipv4.tcp_syncookies = 1 net.ipv4.ip_dynaddr = 1 vm.swappiness = 0 vm.drop_caches = 3 net.ipv4.tcp_moderate_rcvbuf = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_ecn = 0 net.ipv4.tcp_max_orphans = 131072 net.ipv4.tcp_orphan_retries = 1 net.ipv4.conf.default.rp_filter = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv4.tcp_max_syn_backlog = 32768 net.core.netdev_max_backlog = 131072 net.ipv4.tcp_mem = 6085248 16227328 67108864 net.ipv4.tcp_wmem = 4096 131072 33554432 net.ipv4.tcp_rmem = 4096 174760 33554432 net.core.rmem_default = 33554432 net.core.rmem_max = 33554432 net.core.wmem_default = 33554432 net.core.wmem_max = 33554432 net.core.somaxconn = 10000 # ################ Netstat results /# netstat -st IcmpMsg: InType0: 2 InType3: 233754 InType8: 56251 InType11: 23192 OutType0: 56251 OutType3: 437 OutType8: 4 Tcp: 20680741 active connections openings 63642431 passive connection openings 1126690 failed connection attempts 2093143 connection resets received 13059 connections established 2649651696 segments received 2195445642 segments send out 183401499 segments retransmited 38299 bad segments received. 14648899 resets sent UdpLite: TcpExt: 507 SYN cookies sent 178 SYN cookies received 1376771 invalid SYN cookies received 1014577 resets received for embryonic SYN_RECV sockets 4530970 packets pruned from receive queue because of socket buffer overrun 7233 packets pruned from receive queue 688 packets dropped from out-of-order queue because of socket buffer overrun 12445 ICMP packets dropped because they were out-of-window 446 ICMP packets dropped because socket was locked 33812202 TCP sockets finished time wait in fast timer 622 TCP sockets finished time wait in slow timer 573656 packets rejects in established connections because of timestamp 133357718 delayed acks sent 23593 delayed acks further delayed because of locked socket Quick ack mode was activated 21288857 times 839 times the listen queue of a socket overflowed 839 SYNs to LISTEN sockets dropped 41 packets directly queued to recvmsg prequeue. 79166 bytes directly in process context from backlog 24 bytes directly received in process context from prequeue 2713742130 packet headers predicted 84 packets header predicted and directly queued to user 1925423249 acknowledgments not containing data payload received 877898013 predicted acknowledgments 16449673 times recovered from packet loss due to fast retransmit 17687820 times recovered from packet loss by selective acknowledgements 5047 bad SACK blocks received Detected reordering 11 times using FACK Detected reordering 1778091 times using SACK Detected reordering 97955 times using reno fast retransmit Detected reordering 280414 times using time stamp 839369 congestion windows fully recovered without slow start 4173098 congestion windows partially recovered using Hoe heuristic 305254 congestion windows recovered without slow start by DSACK 933682 congestion windows recovered without slow start after partial ack 77828 TCP data loss events TCPLostRetransmit: 5066 2618430 timeouts after reno fast retransmit 2927294 timeouts after SACK recovery 3059394 timeouts in loss state 75953830 fast retransmits 11929429 forward retransmits 51963833 retransmits in slow start 19418337 other TCP timeouts 2330398 classic Reno fast retransmits failed 2177787 SACK retransmits failed 742371590 packets collapsed in receive queue due to low socket buffer 13595689 DSACKs sent for old packets 50523 DSACKs sent for out of order packets 4658236 DSACKs received 175441 DSACKs for out of order packets received 880664 connections reset due to unexpected data 346356 connections reset due to early user close 2364841 connections aborted due to timeout TCPSACKDiscard: 1590 TCPDSACKIgnoredOld: 241849 TCPDSACKIgnoredNoUndo: 1636687 TCPSpuriousRTOs: 766073 TCPSackShifted: 74562088 TCPSackMerged: 169015212 TCPSackShiftFallback: 78391303 TCPBacklogDrop: 29 TCPReqQFullDoCookies: 507 TCPChallengeACK: 424921 TCPSYNChallenge: 170388 IpExt: InBcastPkts: 351510 InOctets: -609466797 OutOctets: -1057794685 InBcastOctets: 75631402 #

  Read the article

• Apache strace to hunt down a memory leak

  - by Zipp

  We have a server with a memory issue: the server keeps allocating itself memory and doesn't release it. We're running Apache. I set MaxReqsPerClient to a really low value just so the threads don't hold a lot of memory, but has anyone seen calls like this? Am I wrong in thinking that it's probably Drupal pulling too much data back from the cache in DB? read(52, "h_index\";a:2:{s:6:\"weight\";i:1;s"..., 6171) = 1368 read(52, "\";a:2:{s:6:\"author\";a:3:{s:5:\"la"..., 4803) = 1368 read(52, ":\"description\";s:19:\"Term name t"..., 3435) = 1368 read(52, "abel\";s:4:\"Name\";s:11:\"descripti"..., 2067) = 1368 read(52, "ions\";a:2:{s:4:\"form\";a:3:{s:4:\""..., 16384) = 708 brk(0x2ab554396000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55f653000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55f753000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55f853000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55f953000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55fa53000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55fb53000 brk(0x2ab554356000) = 0x2ab5542f5000 mmap(NULL, 1048576, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2ab55fc53000 poll([{fd=52, events=POLLIN|POLLPRI}], 1, 0) = 0 (Timeout) write(52, "d\0\0\0\3SELECT cid, data, created, "..., 104) = 104 read(52, "\1\0\0\1\5E\0\0\2\3def\23drupal_database_nam"..., 16384) = 1368 read(52, ";s:11:\"granularity\";a:5:{s:4:\"ye"..., 34783) = 1368 read(52, ":4:\"date\";}s:9:\"datestamp\";a:9:{"..., 33415) = 1368 read(52, "\";i:0;s:15:\"display_default\";i:0"..., 32047) = 1368 read(52, "e as an integer value.\";s:8:\"set"..., 30679) = 1368 read(52, "label' pairs, i.e. 'Fraction': 0"..., 29311) = 1368 top (the procs just keep growing in memory..): 12845 apache 15 0 581m 246m 37m S 0.0 4.1 0:17.39 httpd 12846 apache 15 0 571m 235m 37m S 0.0 4.0 0:12.13 httpd 12833 apache 15 0 420m 117m 37m S 0.0 2.0 0:06.04 httpd 12851 apache 15 0 412m 113m 37m S 0.0 1.9 0:05.32 httpd 13871 apache 15 0 409m 109m 37m S 0.0 1.8 0:04.90 httpd 12844 apache 15 0 407m 108m 37m S 0.0 1.8 0:04.50 httpd 13870 apache 15 0 407m 108m 37m S 0.3 1.8 0:03.50 httpd 14903 apache 15 0 402m 103m 37m S 0.3 1.7 0:01.29 httpd 14850 apache 15 0 397m 100m 37m S 0.0 1.7 0:02.08 httpd 14907 apache 15 0 390m 93m 36m S 0.0 1.6 0:01.32 httpd 13872 apache 15 0 386m 91m 37m S 0.0 1.5 0:03.13 httpd 12843 apache 15 0 373m 81m 37m S 0.0 1.4 0:02.51 httpd 14901 apache 15 0 370m 75m 33m S 0.0 1.3 0:00.78 httpd 14904 apache 15 0 335m 29m 15m S 0.0 0.5 0:00.26 httpd

  Read the article

• Puppet master fails to run under nginx+passenger configuration as rack app, works when run as system service

  - by Anadi Misra

  I get the error [anadi@bangda ~]# tail -f /var/log/nginx/error.log [ pid=19741 thr=23597654217140 file=utils.rb:176 time=2012-09-17 12:52:43.307 ]: *** Exception LoadError in PhusionPassenger::Rack::ApplicationSpawner (no such file to load -- puppet/application/master) (process 19741, thread #<Thread:0x2aec83982368>): from /usr/local/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `gem_original_require' from /usr/local/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `require' from config.ru:13 from /usr/local/lib/ruby/gems/1.8/gems/rack-1.4.1/lib/rack/builder.rb:51:in `instance_eval' from /usr/local/lib/ruby/gems/1.8/gems/rack-1.4.1/lib/rack/builder.rb:51:in `initialize' from config.ru:1:in `new' from config.ru:1 when I start nginx server with passenger module configured, puppet master configured to run through rack. here is the config.ru [anadi@bangda ~]# cat /etc/puppet/rack/config.ru # a config.ru, for use with every rack-compatible webserver. # SSL needs to be handled outside this, though. # if puppet is not in your RUBYLIB: #$:.unshift('/usr/share/puppet/lib') $0 = "master" # if you want debugging: # ARGV << "--debug" ARGV << "--rack" require 'puppet/application/master' # we're usually running inside a Rack::Builder.new {} block, # therefore we need to call run *here*. run Puppet::Application[:master].run and the nginx configuration for puppet master is as follows [anadi@bangda ~]# cat /etc/nginx/conf.d/puppet-master.conf server { listen 8140 ssl; server_name bangda.mycompany.com; passenger_enabled on; passenger_set_cgi_param HTTP_X_CLIENT_DN $ssl_client_s_dn; passenger_set_cgi_param HTTP_X_CLIENT_VERIFY $ssl_client_verify; access_log /var/log/nginx/puppet/master.access.log; error_log /var/log/nginx/puppet/master.error.log; root /etc/puppet/rack/public; ssl_certificate /var/lib/puppet/ssl/certs/bangda.mycompany.com.pem; ssl_certificate_key /var/lib/puppet/ssl/private_keys/bangda.mycompany.com.pem; ssl_crl /var/lib/puppet/ssl/ca/ca_crl.pem; ssl_client_certificate /var/lib/puppet/ssl/certs/ca.pem; ssl_ciphers SSLv2:-LOW:-EXPORT:RC4+RSA; ssl_prefer_server_ciphers on; ssl_verify_client optional; ssl_verify_depth 1; ssl_session_cache shared:SSL:128m; ssl_session_timeout 5m; } however when I run puppet through the ususal puppetmasterd daemon it works perfect with no errors. I can see somehow the nginx+passenger+rack setup fails to initialize while the same works when running the natvie puppetmaster daemon. Any configuration that I am missing?

  Read the article

• How do I troubleshoot root cause of a hung windows (2003) server?

  - by GregW

  I have a pair of Windows (2003 Server) servers both running MS SQL Server (2008 EE) that each hang every few months. This has been occurring intermittently :( for the past 15 months pretty much since we started using the servers. The symptoms are as-follows: I cannot remote desktop in to troubleshoot; when I attempt to, I get stuck on a blank black screen and am never offered a login prompt I can still ping the servers I can still open a SQL connection to the server, and, CURIOUSLY/BIZARRELY, when I do a "select getdate()", the time it returns appears to be stuck on the exact fraction of a second when (I presume) the server hung. Repeated attempts to do "select getdate()" keep getting that same date, suggesting that the clock is frozen. Filesharing attempts to connect to the hung server fail with the error message: "\ServerName is not accessible. You might not have permissions to use this network resource. Contact the administrator of this server to find out if you have access permissions. The server's clock is not synchronized with the primary domain controller's clock." This is consistent with a frozen clock. Post-reboot, if I investigate the Windows Event Viewer logs, I can see many security accesses (coming from me and others) that I recognize were login attempts during the "down" period, but all of them in the security log are associated with that same timestamp of when the server hung. This also suggests the clock is frozen. There is not a clear cause in the Application or System event logs. I have a local Admin account on the server and am in the process of getting a domain-credentialed Admin account for better remote admin access. HP is supposed to be supporting these machines and has some low-level ILO2 access but they seem incapable of finding the root cause. A reboot will "fix" the problem but I would like to get to the root cause and solve the issue. Has anyone ever seen something like this odd clock behavior?! (If it were just one server I'd perhaps say a bad hardware clock, but two?) Can anyone advise me on what I should try to troubleshoot this sort of situation to find the root cause (or what I should tell HP to try?)

  Read the article

• Disable Acer eRecovery system

  - by Joel Coehoorn

  The meat of this question is that I'm looking for a way to either require a password before using a recovery partition or "break" the recovery partition (specifically, Acer eRecovery) in a way that I can later "unbreak" only by booting normally into windows first. Here's the full details: I have a set of new Acer Veriton n260g machines in a computer lab. A lot work went into setting up this lab to work well - for example, Office 2007 and other programs needed by the students were installed, all windows updates are applied, and a default desktop is setup. All in all it's several hours work to fully set up one machine. Unfortunately, I don't currently have the ability to easily image these machines, and even if I did I would want to avoid downtime even while an image is restored. Therefore, I've taken steps to lock them down — namely DeepFreeze and a bios password to prevent booting from anywhere but the frozen hard drive. DeepFreeze is an amazing product — as long as you boot from the frozen hard drive, there is no way to actually make permanent changes to that hard drive. Anything you do is wiped after the machine restarts. It lets me give students the leeway to do what they want on lab computers without worrying about them breaking something. The problem is that even with the bios locked and set to only boot from the hard drive, these Acers still have a simple way to choose a different boot source: shut them down and put a paper click in a little hole at the top while you turn it on again. This puts them into the "Acer eRecovery" mode. This by itself is no big deal — you can still power cycle with no impact. But if you then click through the menu to reset the machine (we're now past the point of curiosity and on to intent) it will wipe the hard drive and restore it to the original state. Of course, a few students have already figured this out and reset a couple machines. That's unfortunate, but inevitable. I don't want to destroy the ability to do this entirely (which I could by repartitioning the drives to remove the recovery partition) but I would like a way to require a password first, or "break" the recovery system in a way that I can "unbreak" only if I first un-freeze the hard drive in DeepFreeze. Any ideas?

  Read the article

• Debugging IO limitation

  - by Martin F

  I have a Fedora box with some severe IO limitations which I have no idea how to debug. The server has a Areca Technology Corp. ARC-1130 12-Port PCI-X to SATA RAID Controller with 12 7200 RPM 1.5 TB disks and a Marvell Technology Group Ltd. 88E8050 PCI-E ASF Gigabit Ethernet Controller. uname -a output: 2.6.32.11-99.fc12.x86_64 #1 SMP Mon Apr 5 19:59:38 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux The server is a file server running Nginx with the stub status module enabled, so I can see the current amount of connections. The problem present itself when I have a high number of simultaneous connections in a writing state. Usually around 350, at this very moment it's at 590 and the server is almost unusable and stuck at 230mbit/s. If I run stop and hit 1 to see CPU core usages I have all 4 cores with around 99% io wait, if I run iotop the nginx workers are the only processes producing any read load, currently at around 25MB/s. I have each of the workers bound to their own core. Initially I figured it was just the disks being bugged. But I've run fscheck and smartmontools checks and found no errors. I also ran an iozone test which you can see the result of here: http://www.pastie.org/951667.txt?key=fimcvljulnuqy2dcdxa Additionally, when the amount of connections are low I have no problem getting a good speed. If I wget over the local network it easily hits 60MB/sec. Right now I just tried putting a file in /dev/shm, then I symlinked a file from the public dir to it and used wget over the local network and only got 50KB/s. Also, if I try to cp /dev/shm/test /root/test it quickly copies around 740MB and then slows down HEAVILY. Again with iotop reporting 99% iowait. I'm not really sure how to go about figuring out what the problems are. It could be a natural disk limitation but then the file from /dev/shm ought to transfer so it seems there's a network limit, but that's fine when there's not many connections. Perhaps it's a TCP stack problem but I really have no idea how to check that. Any suggestions on how to proceed with debugging would be very welcome. If additional information is required then let me know and I'll try to get it. Thanks.

  Read the article

• Making application behind reverse proxy aware of https

  - by akaIDIOT

  https in tomcat being the hassel it is, I've been trying to get an Axis2 webapp to work behind a reverse proxy for ages now, can't seem to get it to work. The proxying itself works like a charm, but the app fails to generate 'links' (or ports as it concerns SOAP) using https. It would seem I need some way to let Axis2 know it is being accessed through https, even though the actual transport to it is done over http (proxied from localhost). The nginx config that proxies https to localhost:8080: server { listen 443; server_name localhost; ssl on; ssl_certificate /path/to/.pem ssl_certificate_key /path/to/.key; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv3:+EXP; ssl_prefer_server_ciphers on; location / { # force some http-headers (avoid confusing tomcat) proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $http_host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto https; # pass requests to local tomcat server listening on default port 8080 proxy_pass http://localhost:8080; } } The proxy itself works fine, the info pages of the webapp work. The problem lies in the ports generated in the .wsdl: <wsdl:service name="WebService"> <wsdl:port name="WebServiceHttpSoap11Endpoint" binding="ns:WebServiceSoap11Binding"> <soap:address location="http://10.10.3.96/axis2/services/WebService.WebServiceHttpSoap11Endpoint/"/> </wsdl:port> <wsdl:port name="WebServiceHttpSoap12Endpoint" binding="ns:WebServiceSoap12Binding"> <soap12:address location="http://10.10.3.96/axis2/services/WebService.WebServiceHttpSoap12Endpoint/"/> </wsdl:port> <wsdl:port name="WebServiceHttpEndpoint" binding="ns:WebServiceHttpBinding"> <http:address location="http://10.10.3.96/axis2/services/WebService.WebServiceHttpEndpoint/"/> </wsdl:port> </wsdl:service> The Host header does its job; it shows 10.10.3.96 in stead of localhost, but as the snippet shows: it says http:// in front of it in stead of https://. My client app can't deal with this... Adding proxyPort and proxyName to the tomcat6 server.xml in the default <Connector> doesn't help; I'm at a loss on how to get this to work properly.

  Read the article

• Bash-Scripting - Munin Plugin don't work

  - by FTV Admin

  i have written a munin-plugin to count the http-statuscodes of lighttpd. The script: #!/bin/bash ###################################### # Munin-Script: Lighttpd-Statuscodes # ###################################### ##Config # path to lighttpd access.log LIGHTTPD_ACCESS_LOG_PATH="/var/log/lighttpd/access.log" # rows to parse in logfile (higher value incrase time to run plugin. if value to low you may get bad counting) LOG_ROWS="200000" # #munin case $1 in autoconf) # check config AVAILABLE=`ls $LIGHTTPD_ACCESS_LOG_PATH` if [ "$AVAILABLE" = "$LIGHTTPD_ACCESS_LOG_PATH" ]; then echo "yes" else echo "No: "$AVAILABLE echo "Please check your config!" fi exit 0;; config) # graph config cat <<'EOM' graph_title Lighhtpd Statuscodes graph_vlabel http-statuscodes / min graph_category lighttpd 1xx.label 1xx 2xx.label 2xx 3xx.label 3xx 4xx.label 4xx 5xx.label 5xx EOM exit 0;; esac ## calculate AVAILABLE=`ls $LIGHTTPD_ACCESS_LOG_PATH` if [ "$AVAILABLE" = "$LIGHTTPD_ACCESS_LOG_PATH" ]; then TIME_NOW=`date` CODE_1xx="0" CODE_2xx="0" CODE_3xx="0" CODE_4xx="0" CODE_5xx="0" for i in 1 2 3 4 5; do TIME5=`date +%d/%b/%Y:%k:%M --date "$TIME_NOW -"$i"min"` CODE_1xx=$(( $CODE_1xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 1' | grep -c " "` )) CODE_2xx=$(( $CODE_2xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 2' | grep -c " "` )) CODE_3xx=$(( $CODE_3xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 3' | grep -c " "` )) CODE_4xx=$(( $CODE_4xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 4' | grep -c " "` )) CODE_5xx=$(( $CODE_5xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 5' | grep -c " "` )) done CODE_1xx=$(( $CODE_1xx / 5 )) CODE_2xx=$(( $CODE_2xx / 5 )) CODE_3xx=$(( $CODE_3xx / 5 )) CODE_4xx=$(( $CODE_4xx / 5 )) CODE_5xx=$(( $CODE_5xx / 5 )) echo "1xx.value "$CODE_1xx echo "2xx.value "$CODE_2xx echo "3xx.value "$CODE_3xx echo "4xx.value "$CODE_4xx echo "5xx.value "$CODE_5xx else echo "1xx.value U" echo "2xx.value U" echo "3xx.value U" echo "4xx.value U" echo "5xx.value U" fi If i run the script on local machine it runs perfectly: root@server1 /etc/munin/plugins # ll lrwxrwxrwx 1 root root 45 2011-12-19 15:23 lighttpd_statuscodes -> /usr/share/munin/plugins/lighttpd_statuscodes* root@server1 /etc/munin/plugins # ./lighttpd_statuscodes autoconf yes root@server1 /etc/munin/plugins # ./lighttpd_statuscodes config graph_title Lighhtpd Statuscodes graph_vlabel http-statuscodes / min graph_category lighttpd 1xx.label 1xx 2xx.label 2xx 3xx.label 3xx 4xx.label 4xx 5xx.label 5xx root@server1 /etc/munin/plugins #./lighttpd_statuscodes 1xx.value 0 2xx.value 5834 3xx.value 1892 4xx.value 0 5xx.value 0 But Munin shows no graph: http://s1.directupload.net/images/111219/3psgq3vb.jpg I have tested the Plugin from munin-server via telnet: root@munin-server /etc/munin/plugins/ # telnet 123.123.123.123 4949 Trying 123.123.123.123... Connected to 123.123.123.123. Escape character is '^]'. # munin node at server1.cluster1 fetch lighttpd_statuscodes 1xx.value U 2xx.value U 3xx.value U 4xx.value U 5xx.value U . Connection closed by foreign host. You can see in the script that value = U only printed, when the script can't check the lighttpd's access.log. But why can't script do it, when running via munin, and when running on local machine all is ok? Is there a bug in my bash-script? I have no Idea. Thanks for helping!

  Read the article

• TeamSpeak 3 Disconnects

  - by ArchUser

  I've recently had a few random TS3 mass disconnects and I'm am curious to know where I may find any applications that can help me determine the cause of any types of TS3 server disconnections as we plan on having many more users in the future. I run an almost empty VPS (OpenVZ) server with an ArchLinux template on it. I have 1.5/2GB of RAM, 2GHz of CPU and plenty of hard drive space, to run for the most part, just my TS3 and a low traffic apache web server. This is what I am investigating. 2011-02-04 06:07:05.130343|INFO |VirtualServer | 1| client disconnected 'Valamoor'(id:224) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.131338|INFO |VirtualServer | 1| client disconnected 'Kevrow'(id:19? reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.191849|INFO |VirtualServer | 1| client disconnected 'scuba'(id:200) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.192633|INFO |VirtualServer | 1| client disconnected '[Ash] Setna'(id:75) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.193350|INFO |VirtualServer | 1| client disconnected 'Akiris'(id:254) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.194047|INFO |VirtualServer | 1| client disconnected 'Marcus'(id:25? reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.194726|INFO |VirtualServer | 1| client disconnected 'Guthry'(id:275) reason 'reasonmsg=connection lost' 2011-02-04 07:18:50.327071|INFO |VirtualServer | 1| client disconnected 'Valamoor'(id:224) reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.339018|INFO |VirtualServer | 1| client disconnected 'Marcus'(id:25? reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.339870|INFO |VirtualServer | 1| client disconnected '[Ash] Setna'(id:75) reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.340515|INFO |VirtualServer | 1| client disconnected 'Guthry'(id:275) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.797353|INFO |VirtualServer | 1| client disconnected 'JohnyRingo'(id:240) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.798517|INFO |VirtualServer | 1| client disconnected 'Maloo roots'(id:196) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.799314|INFO |VirtualServer | 1| client disconnected 'Cpt dravyn'(id:234) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.839254|INFO |VirtualServer | 1| client disconnected 'scuba'(id:200) reason 'reasonmsg=connection lost' etc... I need to determine if it is my hosting provider or my server, and what tools I can use to determine the issues. My VPS host has told me this... "I checked out the node that your VPS runs on and there is no abnormal system load, or I/O wait from the drive. I also checked the bandwidth history from the server and there have been no spikes or outages."

  Read the article

• Backing Up vs. Redundancy

  - by TK Kocheran

  I'm currently in stage 2 of 3 of building my home workstation. What this means is that my RAID-0 array of solid state disks will be backed up nightly to a RAID-5 or RAID-6 array of traditional spinning hard disks. However, it recently dawned on me that redundancy is not backup. The main reason for setting up a RAID array with redundancy was to protect myself in the event of a drive failure to serve as an effective backup solution. Wait. What if a bolt of lightning finds a way to travel into my house, through my surge-protector, into my power supply and physically destroys all of my hard disks and SSDs? Well, in that case, I guess I'd be fine because I generally keep most important files (music, pictures, videos) stored in multiple places like on my laptop, my wife's laptop, and an encrypted USB hard drive. Wait. What if a giant hedgehog meteor attacks my house from space traveling at mach 3 and all machines and hard disks are blown to smithereens. Well, I guess I could find a way to do ridiculously slow and cumbersome rsyncs or backups to Amazon's Glacier. Wait. What if there's a nuclear apocalypse... and at this point I start laughing hysterically. At what point does backing up become irrelevant? I completely understand situation one (mechanical drive failure), situation two (workstation compromised or destroyed somehow), possibly even situation three (all machines and disks destroyed), but situation four? There's no questioning the need for backups. None. However, there are three questions I'd really like addressed: To what level should one backup? I definitely understand the merits of physical disk redundancy. I also believe in keeping important files on multiple machines and thinning out the possibility of losing all of my files. Online backups make sense, but they beg the following question. What should I be backing up remotely and how often? It's no problem storage-wise to back up important files (music, pictures, videos) and even configuration and temporal data for all of the machines in my network (all Linux based)... albeit locally. Transferring to the cloud is another story. Worst-case scenario, if I lost all of my configuration for my individual computers, the reality is that I probably lost the machines too. The cloud is a long way away from here; I can run backups over CAT-6 here and see 100MB/s easily, but I'm afraid that I'm only going to see 2MB/s at best when transferring up to the cloud.

  Read the article

• Blank displays after inactivity, mouse cursor not showing up

  - by Mike Christiansen

  I have a Windows 7 Enterprise x86 machine that is exhibiting some strange problems. After some inactivity (it varies how long it takes), when I come back to my computer, both of my monitors are black. The monitors are on, with a black display. Moving the mouse and pressing keys on the keyboard do not work. This happens at least once a day. When I first encountered the issue, I performed a hard shutdown and restarted the computer. About 10% of the time when I did this, the resolutions on my monitors were messed up. The native resolution on the primary monitor is 1600x900, and the native on my secondary is 1440x900. None of the widescreen resolutions would be present in the display properties. I had 800x600, 1024x768, and 1280x1024. As a workaround to this issue, I've found that if I plug in my secondary monitor as the primary monitor, and leave the secondary unplugged, then Windows will start in 1024x768 on the secondary. Then, I can use Windows 7's "Detect" feature and it finds the 1440x900 resolution, and sets it. Then I have to connect the primary monitor to the secondary port and set it as the primary. Then I can switch the two cables, putting the primary into the primary, the secondary into the secondary. Then use the "Detect" feature again, and it finds the correct resolutions. Some time after performing the above, I discovered that when the screens were blanked, I could simply press "Control+Alt+Delete", type in my password, and everything comes up fine - except my mouse cursor. All applications and features work as intended, except there is no mouse cursor (the mouse actually works though...). I have the "Show location of pointer when I press CTRL key" option selected, so I can press CTRL and use my mouse as normal - but I have no actual cursor. When the computer is in this state, UAC is also not functional. Whenever a UAC prompt appears, the screens go black (the original symptoms) and I have to press Escape to exit UAC. Because of the above symptoms (the UAC black screen thing, etc) I beleive winlogon.exe may be the culprit. However, I have no idea how to fix it. I am unable to restart winlogon.exe due to the problems I am having with winlogon.exe (the UAC black screen) Looking for any ideas.... More information Windows 7 x86 Enterprise Domain environment (I have a secondary account with administrator rights) Dell Optiplex 960 Cannot perform "optional" windows updates due to an activation issue (I am testing a windows 7 image, and an activation infrastructure has not been created yet. However, this issue was happening before I was unable to perform windows update, and windows was up to date at the time Updated video card driver (as an attempt to fixing the resolution issue) Disabled all power saving options Please let me know what else you need to help me solve this issue! Thanks in advance, Mike

  Read the article

• Brand new Mac Pro tower fan suddenly runs full-tilt

  - by Caffeine Coma

  My Quad-Core Mac Pro tower is two days old. Initially, I was impressed with how quiet it was compared to my older Macbook Pro. Then on day two, for some reason it started running very loudly. It's not just a "little" loud- my wife walked into the room and asked what the noise was. At first I thought this was just because I was hitting the CPU a bit (importing my iPhone library into iLife '09, and running Eclipse). But now that that's done, Activity Monitor shows a virtually idle CPU; there's nothing running that ought to be causing this, as far as I can tell. I tried powering it off & letting it cool down for a few minutes to no avail; about 10 seconds after powering up, the box gets loud again. I took a look at it with the side cover off, and it seems to be the fan near the top middle, between the power supply and the disk drive. It can't be a dust issue, as the machine is only 2 days old (and I peeked inside anyway just to be sure- clean). I did do a software update over the past 24 hours or so, but I can't say that it occurred immediately after that. I also did a migration of my old apps and data from my MBPro, for what it's worth. Why is it suddenly so loud? How can I monitor the fan speed and various system temperatures? Here's a link to my temps and fan speeds. UPDATE 1: Took it to the Apple Store. They took it in the back (where it's presumably quieter) and ran a fan diagnostic; no problems were found. The guy also told me that it was "a little loud", but normal. I don't buy it. It was virtually silent the first 24 hours I was using it. They would not replace/service it in the store (grrr... that's why I went there, as directed by Apple Care) but said I could get a replacement from the online store, as it was just purchased. I think I will try that. UPDATE 2: Apple is letting me send it back for a replacement. Glad to see so many responses to this question mentioning that the MacPros are usually silent; it's not all just in my head. :-)

  Read the article

• Looking for a new backup solution to replace dying tape drive

  - by E3 Group

  We're running Windows Server 2003 SBS and another machine with Server 2003 Standard on it. The SBS server is about 7 years old running pretty much 24/7 - a HP server of some description. We have an Ultrium 448 cycling LTO2 400GB tapes daily and incrementally backing up approximately 100gb worth of data (20gb C:\ and system state, 40gb exchange, 40gb database for some crap marketing software) on BackupExec 10D. As of 5 months ago, the backups have been consistently failing with IO errors, bad reads and some write errors. When I say consistent, I mean every time and we haven't had a proper backup for the entire 5 months - So if the server explodes tomorrow, 7 years worth of data will just cease to exist. I've only just recently rejoined the company and am looking at rectifying the more concerning problems, so the first thing I did was try a backup to an USB2.0 external drive. It was excruciatingly slow. In fact it was so slow it took 40 hours and it still wasn't finished. I ended up cancelling it and reconfiguring the selections again to reduce file size. This, however, isn't a permanent solution. I concluded that the IO error was either from a faulty tape drive (which has a tape stuck in there right now and not coming out) or from a dying SCSI controller. Neither of them are good news and both are extremely expensive to fix. I'm operating on an extremely low budget so have been looking at outsourcing the backups. A company in Sydney (where I'm located) offer incremental online backups via a NAS. It costs almost double a new tape drive but offers monthly repayments which will let us get through times when cash flow is minimal. It seems like a sweet deal but it is still a little bit pricey. So I'm looking for a cheaper, yet reliable solution. Maybe some in-house NAS or something offsite? The idea is to avoid using tapes. Are there any recommendations for rectifying my current situation? Or are tapes the only way to go? I'm concerned that the server will die one day in the near future and I must be able to restore it to another server with different hardware.

  Read the article

• TCP/IP & throughput between FreeNAS (BSD) server & other LAN machines

  - by Tim Dickerson

  I have got a question for someone that knows BSD a bit better than me that are in regards to my LAN setup at home/work here outside Chicago. I can't seem to fully optimize my network's (LAN) thoughput via my FreeNAS (BSD based) file server. It runs with the latest FreeBSD release which is modified to support several protocols for file transfers and more. Every machine that is behind my Smoothwall (Linux based) router is on the usual 192.168.0.x subnet and for most part works just fine. Behind the Smoothwall box, all machines are connected to a GB HP unmanaged switch. I host a large WISP here and have an OC-3 connection here at home/work and have no issues with downloading/uploading from/to the 'net'. My problem is with throughput. When I try and transfer large files...really any for that matter..between any of the machines to/and from the FreeNAS server via FTP, the max throughput I can achieve say between a Win 7 or a Linux box is ~65Mbit/sec. All machines are running Intel Pro 1000 GB NIC's and all cable is CAT6. Each is set to 'auto negotiation' and each shows 1500 MTU Full Duplex @1GB so I know the hardware is okay. I have not adjusted the MTU on any machine as I understand it to be pointless unless certain configurations are used (I assume I am not one of those). My settings for the FreeNAS machine are the following: # FreeNAS /etc/sysctl.conf - pertinent settings shown kern.ipc.maxsockbuf=262144 kern.ipc.nmbclusters=32768 kern.ipc.somaxconn=8192 kern.maxfiles=65536 kern.maxfilesperproc=32768 net.inet.tcp.delayed_ack=0 net.inet.tcp.inflight.enable=0 net.inet.tcp.path_mtu_discovery=0 net.inet.tcp.recvbuf_auto=1 net.inet.tcp.recvbuf_inc=524288 net.inet.tcp.recvbuf_max=16777216 net.inet.tcp.recvspace=65536 net.inet.tcp.rfc1323=1 net.inet.tcp.sendbuf_inc=16384 net.inet.tcp.sendbuf_max=16777216 net.inet.tcp.sendspace=65536 net.inet.udp.recvspace=65536 net.local.stream.recvspace=65536 net.local.stream.sendspace=65536 net.inet.tcp.hostcache.expire=1 From what I can tell, that looks to be a somewhat optimized profile for a typical BSD machine acting as a server for a LAN. I might be wrong and just wanted to find out from someone that knows BSD better than I do if indeed that is ok or if something is out of tune or what. Are there other ways I would find better for P2P file transfers? I honestly do not know what I SHOULD be looking for with respect to throughput between the NAS box and another client when xferring files via FTP, but I am told that what I get on average (40-70MB/sec) is too low for what it could be. I have thought about adding another NIC in the FreeNAS box as well as the Win7 machine and use a X-over cable via a static route, but wanted to check with someone first to see if that might be worth it or not. I don't know if doing that would bypass the HP GB switch and allow for a machine to machine xfer anyways. The FTP client I use is: Filezilla and have tried both active and passive modes with no real gain over each other. The NAS box runs ProFTPD.

  Read the article

• Rails 3 shows 404 error instead of index.html (nginx + unicorn)

  - by Miko

  I have an index.html in public/ that should be loading by default but instead I get a 404 error when I try to access http://example.com/ The page you were looking for doesn't exist. You may have mistyped the address or the page may have moved. This has something to do with nginx and unicorn which I am using to power Rails 3 When take unicorn out of the nginx configuration file, the problem goes away and index.html loads just fine. Here is my nginx configuration file: upstream unicorn { server unix:/tmp/.sock fail_timeout=0; } server { server_name example.com; root /www/example.com/current/public; index index.html; keepalive_timeout 5; location / { try_files $uri @unicorn; } location @unicorn { proxy_pass http://unicorn; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $host; proxy_redirect off; } } My config/routes.rb is pretty much empty: Advertise::Application.routes.draw do |map| resources :users end The index.html file is located in public/index.html and it loads fine if I request it directly: http://example.com/index.html To reiterate, when I remove all references to unicorn from the nginx conf, index.html loads without any problems, I have a hard time understanding why this occurs because nginx should be trying to load that file on its own by default. -- Here is the error stack from production.log: Started GET "/" for 68.107.80.21 at 2010-08-08 12:06:29 -0700 Processing by HomeController#index as HTML Completed in 1ms ActionView::MissingTemplate (Missing template home/index with {:handlers=>[:erb, :rjs, :builder, :rhtml, :rxml, :haml], :formats=>[:html], :locale=>[:en, :en]} in view paths "/www/example.com/releases/20100808170224/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/paperclip/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/haml/app/views"): /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/paths.rb:14:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/lookup_context.rb:79:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/base.rb:186:in `find_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:45:in `_determine_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:23:in `render' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/haml-3.0.15/lib/haml/helpers/action_view_mods.rb:13:in `render_with_haml' etc... -- nginx error log for this virtualhost comes up empty: 2010/08/08 12:40:22 [info] 3118#0: *1 client 68.107.80.21 closed keepalive connection My guess is unicorn is intercepting the request to index.html before nginx gets to process it.

  Read the article

• Passenger 2.2.4, nginx 0.7.61 and SSL

  - by boompa

  Has anyone had any luck configuring Passenger and nginx with SSL? I've spent hours trying to get this configuration working as I'd like, using what few resources there are out there on the net, and I can't get any of the supposedly forwarded headers to show up in the Rails controller. For example, with a conf file of the following (and multiple variations thereof): server { listen 3000; server_name .example.com; root /Users/website/public; passenger_enabled on; rails_env development; } server { listen 3443; root /Users/website/public; rails_env development; passenger_enabled on; ssl on; #ssl_verify_client on; ssl_certificate /Users/website/ssl/server.crt; ssl_certificate_key /Users/website/ssl/server.key; #ssl_client_certificate /Users/website/ssl/CA.crt; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-SSL-Subject $ssl_client_s_dn; #proxy_set_header X-SSL-Issuer $ssl_client_i_dn; proxy_redirect off; proxy_max_temp_file_size 0; } and Rails code in the controller like this: request.headers.each { |k, v| RAILS_DEFAULT_LOGGER.error "Header #{k} Val #{v}" } other headers appear, but not those set in nginx, e.g.: Header rack.multithread Val false Header REQUEST_URI Val /login/new Header REMOTE_PORT Val 64021 Header rack.multiprocess Val true Header PASSENGER_USE_GLOBAL_QUEUE Val false Header PASSENGER_APP_TYPE Val rails Header SCGI Val 1 Header SERVER_PORT Val 3443 Header HTTP_ACCEPT_CHARSET Val ISO-8859-1,utf-8;q=0.7,*;q=0.7 Header rack.request.query_hash Val Header DOCUMENT_ROOT Val /Users/website/public I've even gone so far as to modify Passenger's abstract_request_handler's main_loop method, i.e., headers, input = parse_request(client) if headers if headers[REQUEST_METHOD] == PING process_ping(headers, input, client) else headers.each { |h,v| log.unknown "abstract_request_handler: #{h} = #{v}" } process_request(headers, input, client) end end only to find that the supposedly added headers do not exist there either: abstract_request_handler: HTTP_KEEP_ALIVE = 300 abstract_request_handler: HTTP_USER_AGENT = Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1) Gecko/20090624 Firefox/3.5 abstract_request_handler: PASSENGER_SPAWN_METHOD = smart-lv2 abstract_request_handler: CONTENT_LENGTH = 0 abstract_request_handler: HTTP_IF_NONE_MATCH = "b6e8b9afbc1110ee3bf0c87e119252ad" abstract_request_handler: HTTP_ACCEPT_LANGUAGE = en-us,en;q=0.5 abstract_request_handler: SERVER_PROTOCOL = HTTP/1.1 abstract_request_handler: HTTPS = on abstract_request_handler: REMOTE_ADDR = 127.0.0.1 abstract_request_handler: SERVER_SOFTWARE = nginx/0.7.61 abstract_request_handler: SERVER_ADDR = 127.0.0.1 abstract_request_handler: SCRIPT_NAME = abstract_request_handler: PASSENGER_ENVIRONMENT = development abstract_request_handler: REMOTE_PORT = 64021 abstract_request_handler: REQUEST_URI = /login/new abstract_request_handler: HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.7 abstract_request_handler: SERVER_PORT = 3443 abstract_request_handler: SCGI = 1 abstract_request_handler: PASSENGER_APP_TYPE = rails abstract_request_handler: PASSENGER_USE_GLOBAL_QUEUE = false I'm tired of banging my head against the wall, so I'd truly appreciate any help I can get!

  Read the article

• SMTP host name vs. domain in "From:" address vis-a-vis Email Deliverability

  - by Jared Duncan

  I'm trying to implement (or make sure that I'm correctly following) email sending best practices to improve deliverability, but the role of the smtp server's host name vs the domain name of the From: email address seems to be unclear, even after reading dozens of people's articles/input. Specifically, I understand that to satisfy the reverse DNS check, there must be a PTR record for the IP address of the sending machine that yields a domain name that matches the host name of the sending machine / SMTP server. Some say it needs to match the one given by the "hostname" command, most say it's the one provided with the HELO / EHLO statement, and this guy even says they MUST be the same (according to / enforced by what, I don't know; that's only a minor point of confusion, anyhow). First, what I can't find anywhere is whether or not the domain name of the From: email address needs to match the domain name of the SMTP server. So in my case, I have a VPS with linode. It primarily hosts a particular domain of mine, example.com, but I also sometimes do work on other projects: foo.com and bar.com. So what I'm wondering is if I can just leave the default linode PTR record (which resolves to abc.def.linode.com), make sure that abc.def.linode.com is what my mail server (qmail) is configured to say at HELO, and then proceed to use it to send out emails for example.com, foo.com, et al. If so, then I am confused by the advice given here, specifically (in a listing of bad case scenarios): No SPF record for the domain being used in the HELO command Why would THAT domain need an SPF record? And if it does, which domain should it provide whitelisting for: the HELO domain, or the domain of the From: email address (envelope sender)? Also, which domain would need to accept mail sent to [email protected]? If the domains must be the same, that would seem rather limiting to me, because then for every domain you wanted to send email from, you'd have to get another IP address for it. It would also compromise or ruin one's ability to do non-email sending things (e.g. wget) relatively anonymously. However, the upside--if this is the case--is that it would make for a far less confusing setup. I'm currently using the linode.com SMTP+PTR domain and example.com From: address combination without much of any deliverability issue, but my volume is very low and I'd like to know if someone out there has experience with larger volumes and has specifically tested the difference and/or has inside knowledge and/or has an authoritative answer (and source) for this particular question. I'm happy to clarify anything, let me know. Thanks in advance.

  Read the article

• Why does Ubuntu 9.10 hang during boot at "Booting processor 1 APIC 0x1 ip 0x6000"?

  - by BraeburnDev

  I recently installed a new copy of Ubuntu 9.10 (Kernel 2.6.31-14) on to my Hp Pavilion dv6t, so I can setup a Linux development environment. The install went flawlessly and I proceeded with Ubuntu's udate manager's long list of updates (292 in all). I also setup a swap file and activated a Nvidia 185 driver for the Nvidia 260m GPU on the machine. After all this was done I restarted the computer and booted into Ubuntu this time with a newer 2.6.31-19 Kernel which was installed from the update manager. During booth the computer hung at this point: Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013136] Performance Counters: Nehalem/Corei7 events, Intel PMU driver. Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013141] ... version: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013142] ... bit width: 48 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013144] ... generic counters: 4 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013146] ... value mask: 0000ffffffffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013147] ... max period: 000000007fffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013149] ... fixed-purpose counters: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013151] ... counter mask: 000000070000000f Feb 24 14:23:12 braeburn-laptop kernel: [ 0.015539] ACPI: Core revision 20090521 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052264] Setting APIC routing to flat Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052639] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.152580] CPU0: Intel(R) Core(TM) i7 CPU Q 720 @ 1.60GHz stepping 05 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.270845] Booting processor 1 APIC 0x1 ip 0x6000 I can post a full kern.log of this boot process if requested. Hopefully this is enough information to go on. I should add that I'm still new to configuring and running a Linux OS although I know enough basic command line usage to do software development. This is my attempt to become more familiar with Linux and manage my own system. I'd like to get some insight on the nature of this system hang, what the problem is and how to resolve it. At this point I can scrap the install if I broke something, but my intuition says this is an issue with the kernel recognizing the correct hardware configuration for my system, or perhaps this is an issue with the APIC drivers managing Nehalem's new power management capabilities? Thanks for looking at this issue and providing feed back.

  Read the article

• Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

  - by Software Monkey

  I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

  Read the article

• Buying a new printer instead of replacing ink?

  - by Kelsey

  With prices of basic printers being around $40 - $50 and a ink cartridge being around $20 - $30 each for black AND color. It costs me more to replace the printer's ink than to just buy a brand new printer. This just seems like a total waste of materials though (I have 4 printers sitting in my basement with no ink). I know the ink cartridges are smaller (not as full) in a new printer but I go through it in about 1 to 1.5 years only and by then my $40 gets me a better printer to boot. Also with certain printers the heads are not part of the ink (Epson use to do this and still might) so I get new heads as well. Is this a bad practice? Are retailers making this a reality when they are selling working hardware cheaper than replacement parts? Is there something more I should be considering? Edit: Some background, long ago I bought an Epson printer which I used to print docs etc vary rarely. The ink started running low so I bought to new carts for around $60 if I recall. The printer then stopped working so I replaced the carts with the new ones but the head was dead on the black which was not worth repairing. I bought a new HP printer for $49. This lasted around 1.5yrs and then the ink ran out, I went to buy new carts and the guy at the store got me to buy a new printer (that was smaller, faster, higher dpi, etc) and it was cheaper than replacing the ink. When the ink ran out on that one I bought a new printer again, etc. The printer gets used maybe once a week at most and I never print photos or anything. It normally is jsut stored away unplugged accumulating dust. People say to buy a laser printer but they are much larger, do not print color, (in the price range I am looking at) and might have the exact same issues. The problem I see is the manufacturer is making my behaviour possible by selling new printers at a loss hoping that they will cash in on the ink later. How can they produce a printer for so cheap which HAS ink in it, and the refills cost more than the unit? It can't.

  Read the article

• Revolutionary brand powder packing machine price from affecting marketplace boom and put on uniform in addition to a lengthy service life

  - by user74606

  In mining in stone crushing, our machinery company's encounter becomes much more apparent. As a consequence of production capacity in between 600~800t/h of mining stone crusher, stone is mine Mobile Cone Crushing Plant Price 25~40 times, effectively solved the initially mining stone crusher operation because of low yield prices, no upkeep problems. Full chunk of mining stone crusher. Maximum particle size for crushing 1000x1200mm, an effective answer for the original side is mine stone provide, storing significant chunks of stone can not use complications in mines. Completed goods granularity is modest, only 2~15mm, an effective option for the original mine stone size, generally blocking chute production was an issue even the grinding machine. Two types of material mixed great uniformity, desulfurization of mining stone by adding weight considerably. Present quantity added is often reached 60%, effectively minimizing the cost of raw supplies. Electrical energy consumption has fallen. Dropped 1~2KWh/t tons of mining stone electrical energy consumption, annual electricity savings of one hundred,000 yuan. Efficient labor intensity of workers and also the atmosphere. Due to mine stone powder packing machine price a high degree of automation, with out human make contact with supplies, workers working circumstances enhanced significantly. Positive aspects, and along with mine for stone crushing, CS series cone Crusher has the following efficiency traits. CS series cone Crusher Chamber is divided into 3 unique designs, the user is usually chosen in accordance with the scenario on site crushing efficiency is high, uniform item size, grain shape, rolling mortar wall friction and put on uniform in addition to a extended service life of crushing cavity-. CS series cone Crusher utilizes a one of a kind dust-proof seal, sealing dependable, properly extend the service life of the lubricant replacement cycle and parts. CS series Sprial Sand washer price manufacture of important components to choose unique materials. Each and every stroke left rolling mortar wall of broken cone distances, by permitting a lot more products into the crushing cavity, as well as the formation of big discharge volume, speed of supplies by way of the crushing Chamber. This machine makes use of the principle of crushing cavity, also as unique laminated crushing, particle fragmentation, so that the completed product drastically improved the proportions of a cube, needle-shaped stones to lower particle levels extra evenly.

  Read the article

• The ping response time doesn't reflect the real network response time

  - by yangchenyun

  I encountered a weird problem that the response time returned by ping is almost fixed at 98ms. Either I ping the gateway, or I ping a local host or a internet host. The response time is always around 98ms although the actual delay is obvious. However, the reverse ping (from a local machine to this host) works properly. The following is my route table and the result: route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 100 0 0 eth1 60.194.136.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 # ping the gateway ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_req=1 ttl=64 time=98.7 ms 64 bytes from 192.168.1.1: icmp_req=2 ttl=64 time=97.0 ms 64 bytes from 192.168.1.1: icmp_req=3 ttl=64 time=96.0 ms 64 bytes from 192.168.1.1: icmp_req=4 ttl=64 time=94.9 ms 64 bytes from 192.168.1.1: icmp_req=5 ttl=64 time=94.0 ms ^C --- 192.168.1.1 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4004ms rtt min/avg/max/mdev = 94.030/96.149/98.744/1.673 ms #ping a local machine ping 192.168.1.88 PING 192.168.1.88 (192.168.1.88) 56(84) bytes of data. 64 bytes from 192.168.1.88: icmp_req=1 ttl=64 time=98.7 ms 64 bytes from 192.168.1.88: icmp_req=2 ttl=64 time=96.9 ms 64 bytes from 192.168.1.88: icmp_req=3 ttl=64 time=96.0 ms 64 bytes from 192.168.1.88: icmp_req=4 ttl=64 time=95.0 ms ^C --- 192.168.1.88 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 95.003/96.696/98.786/1.428 ms #ping a internet host ping google.com PING google.com (74.125.128.139) 56(84) bytes of data. 64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=1 ttl=42 time=99.8 ms 64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=2 ttl=42 time=99.9 ms 64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=3 ttl=42 time=99.9 ms 64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=4 ttl=42 time=99.9 ms ^C64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=5 ttl=42 time=99.9 ms --- google.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 32799ms rtt min/avg/max/mdev = 99.862/99.925/99.944/0.284 ms I am running iperf to test the bandwidth, the rate is quite low for a LAN connection. iperf -c 192.168.1.87 -t 50 -i 10 -f M ------------------------------------------------------------ Client connecting to 192.168.1.87, TCP port 5001 TCP window size: 0.06 MByte (default) ------------------------------------------------------------ [ 4] local 192.168.1.139 port 54697 connected with 192.168.1.87 port 5001 [ ID] Interval Transfer Bandwidth [ 4] 0.0-10.0 sec 6.12 MBytes 0.61 MBytes/sec [ 4] 10.0-20.0 sec 6.38 MBytes 0.64 MBytes/sec [ 4] 20.0-30.0 sec 6.38 MBytes 0.64 MBytes/sec [ 4] 30.0-40.0 sec 6.25 MBytes 0.62 MBytes/sec [ 4] 40.0-50.0 sec 6.38 MBytes 0.64 MBytes/sec [ 4] 0.0-50.1 sec 31.6 MBytes 0.63 MBytes/sec

  Read the article

• How to know the source of certain TCP traffic on AIX

  - by A.Rashad

  We have two AIX boxes, one for production system and another for testing. both systems are running ATM machine switches, where the ATM device is connected via TCP socket. we had an issue on production system where the machine would power off or get disconnected but the netstat -na | grep <IP of machine > would still mention that the socket is up when simulated that case on the UAT environment, the problem did not happen, where the socket would terminate in 3 to 5 minutes. when sniffed on the traffic between the machine and ATM we found that no traffic takes place on production while there is some sort of heartbeat on UAT. but it is not initiated by the application. $>tcpdump | grep -v "10.2.2.71" | grep -v "HSRP" | grep "10.3.1.30" tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on en6, link-type 1, capture size 96 bytes 09:08:13.323421 IP server073.afs3-callback > 10.3.1.30.impera: . 278204201:278204202(1) ack 3307884029 win 164 09:08:13.335334 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:08:23.425771 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:08:23.425789 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 09:09:13.628985 IP server073.afs3-callback > 10.3.1.30.impera: . 0:1(1) ack 1 win 164 09:09:13.633900 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:09:23.373634 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:09:23.373647 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 while on production, that traffic is not there. we want to know where this traffic is initiated from to implement on production to sense disconnection our comms parameters are: tcp_keepcnt = 2 tcp_keepidle = 100 tcp_keepinit = 150 tcp_keepintvl = 150 tcp_finwait2 = 1200 can anyone help?

  Read the article

• Core i7 c1e and speedstepping - BSOD on shutdown

  - by DeaconDesperado

  I'm having an interesting problem with my recent Core i7 Digital Audio workstation build that I am curious to see if others have encountered. First, here are the specs on the machine. ASUS P6TD Deluxe Intel X58 Socket LGA1366 MB Intel Core i7-950 3.06Ghz 8M LGA1366 CPU CORSAIR DOMINATOR 6GB (3 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 Western Digital Caviar Black WD5001AALS 500GB Plus a couple ASUS optical drives and a 750W Corsair PSU. Running Windows 7 x64. All this is connected to the nefarious Digi 002 firewire audio interface for use with Pro Tools. I following mostly the specs posted by many other I7 users in the digidesign community who pooled their collective knowledge in this thread. Now after completing my build, I fell victim to the "UD5 squeal" described at that forum thread. So taking the advice posted, I disabled c1e advanced halt state and Intel speed stepping (I would likely have done this anyway to maintain a stable clock, power consumption isn't really a relevant concern on this machine.) I enabled XMP to set the ram timings properly as well. What I am experiencing is a BSOD upon shutdown, but only immediately after windows fully exits and ends all processes. The error is a MACHINE_CHECK_EXCEPTION 0x000000. The funny thing is that it is extremely intermitent and only occurs if the shutdown immediately followed a period of relative idleness. It does not a generate a minidump, I suspect because windows monitoring has terminated by the time this error occurs. No damage is evident and one can simply turn off manually and the system will act as though a proper shutdown had occurred. If anything it is a annoyance, I just want to be certain it is not affecting my long term stability. I have read that the i7 950 does not like DRAM voltages past 1.65, but that they are acceptable if they are within .5 of the BLCK setting. I have tried disabling XMP and setting all timings to auto and the problem still manifests in an identical way. It is suspect that the cpu idleness preceding shutdown is the determining factor, as both c1e and speedstepping are both settings intended to modify handling of this state. Any suggestions or prior experiences would be greatly appreciated. EDIT: The behavior very closely resembles what's described in this thread: http://www.tomshardware.com/forum/12003-63-shut-problem-windows The benign nature of it of is identical. I can't seem to download the hotfix cited there however.

  Read the article

• Connecting multiple ColdFusion 10 instances to a single Apache 2.2 server

  - by Adam Cameron

  This is on Windows 7 Home Premium edition. I have got two ColdFusion 10 (updater 2) instances: "cfusion" (the default one), and "scratch". I have got a single instance of Apache 2.2 running. Within Apache, I have set up two virtual hosts, each of which needs to be served by a different ColdFusion instance. Each of the CF instances serves files fine via Tomcat's internal web server. Apache serves vanilla HTML files fine too. So both CF instances, and both virtual hosts separately work OK. I can get wsconfig.exe to connect either one of the CF instances to the Apache server, and serve CF files via Apache & that instance. However I cannot find a way of connecting the second CF instance to Apache as well, so that both CF instances are conected, each serving one of the virtual hosts. WSConfig doesn't seem to understand the notion of "multiple CF instances", and the changes it makes to the httpd.conf (via mod_jk.conf) does not seem to be implemented in such a way as to accommodate multiple CF instances talking to a single Apache instance, or multiple virtual hosts. I freely admit to not being confident enough with how mod_jk (or even really httpd.conf) works to be able to guess if I can change stuff to make it work. If I try to add the second CF instance using WSConfig, I just get a message "the web server is already configured for ColdFusion". Be that as it may... not the instance of ColdFusion I want to connect it to! If I remove the existing connector to whichever instance is already connected, I can then connect the other one no problems. Not that this helps, but it demonstrates that the CF instance can connect to Apache. This all used to be fairly straight fwd under older versions of CF and JRun :-( The only docs I have found are on the "Connect multiple Apache virtual hosts on a web server to a single ColdFusion server" page, but that specifically only deals with a single CF instance. There is no equivalent page for multiple CF instances. I'm kinda hoping I can move some of the mod_jk config into my virtual host entries in httpd-vhosts.conf (this is how it used to work for JRun), but I've no idea what to put where. I think I've covered all the necessary info here? If not, sing out and I'll add more. Thanks. PS: tried to specifically tag this as "ColdFusion-10" as the answer will be different from previous CF versions, but it won't let me cos my rep on this site is too low (odd how it doesn't consider my rep from other S/O sites...). If someone with sufficient rep can add it, that'd be cool: it's probably a valid tag to have. Ta.

  Read the article

< Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >