Search Results

Search found 19471 results on 779 pages for 'network troubleshooting'.

Page 346/779 | < Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >

• Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

  - by ale

  I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• How to correctly set up iWARP? Preferably on loopback

  - by ajdecon

  iWARP is a protocol for doing remote direct memory access (RDMA) on top of TCP/IP, so that it can work with Ethernet and other network types as opposed to Infiniband. It works with many of the standard IB interfaces - the IB verbs, for example - so it's all pretty transparent. I'm doing some IB-verbs programming (mostly for the sake of learning about how they work better), and it'd be wonderfully convenient for me if I could use iWARP to do RDMA over my loopback interface, so that I could test some of my code without getting on our IB-connected cluster. :-) But I cannot figure out how to get a "local development environment" set up: there are no tutorials I'm aware of for even setting up iWARP from scratch on a server or a network interface. Can anyone give me a tutorial or point me in the right direction? Environment is Fedora 16 running in VirtualBox.

  Read the article

• Accessing the Internet via browser

  - by ucas

  I am on Windows 7 and using Firefox browser. I am using WiFi, but since the morning I cannot access the Internet via the browsers (Firefox, Chrome, or IE). The laptop shows there is Internet connection, Skype is online, but I can't reach the Internet. Then I launched Tor application which creates secure channel and provides its Firefox browser. Well, I can now access the Internet over that browser. So, what might be the problem causing this malfunction? The error: The connection has timed out The server at mail.google.com is taking too long to respond. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Best regards

  Read the article

• why do Vagrant docs suggest using public IP address 33.33.33.10 for local VMs?

  - by Gert

  I'm following a tutorial to set up vagrant (a tool to build and configure portable virtual machine images), and it seems that vagrant documentation suggests using IPv4 address 33.33.33.10 to configure a new box. That is a publicly routed IP adress, so I'm a bit confused why using this address is suggested. Since I don't own this network, I should not use an address from the 33.33.33.10/8 range. Am I correct in thinking that I should only use either a public address from a network I own, or an address from one of the private ranges as defined in RFC 1918? If so, why does Vagrant documentation suggest otherwise?

  Read the article

• "Play on another device" function not working with Samsung Allshare

  - by Tural Teyyuboglu

  Briefly I can't get work "Play on another device" function More detailed My Samsung TV (which support network) and PC are in the same network. The problem is, I can play PC contents from TV. But when I try to control TV remotely from Allshare software (PC), it shows TV only as connected device: But not as remote player in "players" list The result Tried to turn off firewall completely, reset router, re-install software. No success. Please help. BTW. On this link they kinda explained how to do it, but I software doesn' detect the TV as player in my case: http://www.samsung.com/global/allshare/pcsw/quickguide.html

  Read the article

• VLC RTP Streaming in FC12

  - by Matt D

  I'm trying to get VLC to work streaming RTP audio/video over my office network. The goal is multicast a/v streaming. In all test cases, we are streaming from VLC to VLC. I am able to stream from Windows to Windows, and from Fedora to Windows, but not from Windows to Fedora. Additionally, I am unable to receive a LOCAL stream from one instance of VLC to another, within Fedora. I don't see any reason why this would be. The buffer indicator (where the elapsed/total time is normally displayed) never shows any connectivity, so it would appear to be a network problem, but since I am able to stream from Fedora to Windows (same IP, same port) I thought it would be something else. Does anyone know of a solution to this issue?

  Read the article

• Issues connecting to WPA2 with User Authentication Mavericks?

  - by heinst

  I was on all the builds of the Mavericks beta and connecting to my University's network was fine. Then I upgraded to the public release and now I can't seem to connect to the internet. I can connect to other networks, but not my schools. Its a WPA2 network with a User Authentication. And my MacBook is a 2011? 2.2 GHz first gen i7 Quad Core with 8 GBs of RAM. Does anyone else have the same issue? Any tips on how to fix it? Thanks! heinst

  Read the article

• Cannot Join a Domain on VM

  - by arvind0007

  Hi Guys. I have installed Windows 2003 server R2 on a VM. This VM is running on Windows XP PRO. When i try to make this XP Pro PC join the domain on the VM it tries to locate the server and gives me the following error message " The specified network name is no longer available", despite the fact that i can still see this domain on my network. can anyone help with this please. This is the very first time i am trying connecting a client to a VM server so hope am not doing anything wrong.. thanks

  Read the article

• Simple NAT router for ESX

  - by Evan M.

  Hi Guys, I'm looking for a simple virtual appliance that I can deploy to my ESX environment to use as a virtual NAT router / firewall to create an isolated network that I can easily give internet access too. Basic setup: ESX Host, has 2 vswitches configured: 1 is connected to the physical LAN, the other is isolated. I need an appliance that I can add 2 vNICs to, and attach one to the isolated vSwitch, the other to the LAN, to give the isolated network outbound access (so it can reach the internet). Anyone have an appliance that I can setup quickly to do so? Thanks.

  Read the article

• Frequent disconnects using wlan AR9285

  - by John Neil

  I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

  Read the article

• Configure IIS 6 to deny access to specific file based upon IP address

  - by victorferreira

  Hello guys, We are using IIS 6 as our webserver. And we need to deny the access for one specif file, placed in only one specific URL, to everybody OUTSIDE the local network. In other words, if somebody is trying to access that filme/page from their own computer at home, using the internet, they must not succeed. But, if the same person try to do that at the same network of the web server, its ok. I am not sure about that, but Apache uses ORDER DENY,ALLOW. You specify the URL, allow or deny to all or to a range of IP. Any suggestions? Thanks!

  Read the article

• NAT and ISP Subnet when load balancing on pfsense?

  - by dannymcc

  I have a pfsense box that I'm trying to plan the configuration for. I am going to be load balancing two ISP's, each with their own /29 static IP subnet. The question I have is in relation to the way those IP's are associated with workstations on the local network. Currently I have some workstations with local (192.168.1.0/29) IP addresses, and other more complicated workstation setups have their own public IP address. Some of the more complicated systems have a NAT 1:1 configuration where I forward a public IP address to a local IP address. Others however are directly on the ISP subnet and cannot be seen on our local network. Is this configuration possible with pfsense? If so, what terms should I be looking through the documentation for? Here is a simple/brief diagram of what I am trying to achieve.

  Read the article

• Slow LAN transfer from 3rd party computer

  - by Chris

  Hi Everyone, I've got an odd problem that I'm not really sure where to start the troubleshooting process. I have a 'server' with Windows Server 2008R2 (64-bit) installed and it has a couple of hard drives. If I Remote Desktop into the server and transfer files from one HD to the other, all it fine. If however, I use my workstation (Windows 7 64bit) and open up a shared resource on the server and transfer a file from one hard drive on the server to another HD on the server (not using Remote Desktop, just Windows explorer/Network places), the transfer crawls... It takes about 5mins to discover files/calculate the transfer and then starts transferring at speeds like 56KB/s - 200KB/s. Both machines have Marvel GigE network ports with a TrendNet 8-port green GigE switch. I've set Jumbo packets to 9K on both machines...

  Read the article

• Windows 7 - Remote Desktop - multiple credentials

  - by w--

  My home network consists of a couple Windows XP machines and a Windows 7 box. One of the Windows XP boxes is like a shared server accessed via Remote Desktop. I have an account on there and my gf has another. Previously I was able to save RDC shortcuts to this shared server including credentials. So in order to access the server from a computer on the network, I just needed to open the shortcut. I thus would have two shortcuts, one for my account and one for my gf's. In Windows 7, it seems to store credentials for a box based on machine name. I.e. I can only store one set of credentials per machine name. This seems incredibly stupid so my question is: In Windows 7, is there some way to have RDC shortcuts that use different credentials to login to the same target box?

  Read the article

• ArchBeat Link-o-Rama for 2012-09-25

  - by Bob Rhubart

  Oracle 11gR2 RAC on Software Defined Network (SDN) | Gilbert Stan "The SDN [software defined network] idea is to separate the control plane and the data plane in networking and to virtualize networking the same way we have virtualized servers," explains Gil Standen. "This is an idea whose time has come because VMs and vmotion have created all kinds of problems with how to tell networking equipment that a VM has moved and to preserve connectivity to VPN end points, preserve IP, etc." H/T to Oracle ACE Director Tim Hall for the recommendation. ServerSent-Events on WebLogic Server | Steve Buttons "The HTML5 ServerSent-Event model provides a mechanism to allow browser clients to establish a uni-directional communication path to a server, where the server is then able to push messages to the browser at any point in time," explains Steve "Buttso" Buttons. Focus on Architects and Architecture This handy guide for sessions and other activities at Oracle OpenWorld 2012 focuses on IT architecture in all its many facets and permutations. Operating System Set-up for WebLogic Server | Rene van Wijk Oracle ACE Rene van Wijk shows you how to set-up an operating system for WebLogic Server. "We will use VMware as our virtualization platform and use CentOS as the operating system," says van Wijk. "We end the post by showing how the operating system can be tuned when running a Java process such as WebLogic Server." Free eBook: Oracle SOA Suite - In the Customer's Words If you find yourself in the position of having to sell the idea of Service-oriented Architecture to business stakeholders this free e-book may come in very handy. Check out "Oracle SOA Suite: In the Customer's Words. (Registration / Oracle.com login required.) Thought for the Day "The first rule of any technology used in a business is that automation applied to an efficient operation will magnify the efficiency. The second is that automation applied to an inefficient operation will magnify the inefficiency." — Bill Gates Source: BrainyQuote.com

  Read the article

• Naming your website longname.com vs shortcatchy.net vs shortcatchy.info

  - by jskye

  I'm designing a website that will basically be a social network for sharing information. I have the domain $$$$d.net and the same domain $$$$d.info where $$$$ is a word (that runs into the d) pertaining to the purpose of the site . The .com of this domain was already taken, but they've got nothing showing. They only have a not reached google error showing ie. dont seem to be trying to sell it either. I also have the long name of the site $$$$------&&&&&&&&&.com where the words $$$$ and &&&&&&&&& would contribute relevant seo to the site. In fact the word $$$$------ would also if a one letter spelling mistake is recognised at all by google, which i doubt but am unsure about. But as a brandname the $$$$------ word still works relevantly. Which do you think is a better choice to use? The short catchy name with the .info for relevance to information The .net which is more familiar than .info but slightly less relevant maybe. (But i think net as in network still works cos as i said it will be a social networking site). The long, .com domain which has more SEO plus a pun albeit on a spelling mistake. I know its kind of a subjective question and also hard to answer without knowing the name (which I've obfuscated because I'm only in initial design stage) but nevertheless im interested in what some of you guys think.

  Read the article

• Is it necessary to add an HP printer to CUPS using the hplip URI?

  - by JPbuntu

  I recently setup a CUPS print server (Ubuntu server 12.04) and I having trouble with performance of a HP Color LaserJet Printer CP3505n. The printer pauses for about a second between printing each page, which is annoying when there is a lot of printing to be done. This doesn't happen when the printer is installed directly to a Windows client. In an attempt to fix this I have setup the printer a couple different ways. I decided not to do a Samba share since this wiki said IPP is preferred. First Method Added to HP LaserJet to CUPS as a Discovered Network Printer, and selected HP Color LaserJet cp3505 hpijs pcl3, 3.12.2 (en) driver. I did not use a hplip URI. Second Method (hplip URI) I thought adding hplip to the mix might improve the performance, so I added the printer like this: Ran hp-setup -m 192.168.2.60, prompted to select driver Selected HP Color LaserJet cp3505 hpijs pcl3, 3.12.2 (en) Used hplip to generate a URI: hp-makeuri 192.168.2.60 Then added the printer to CUPS as a Local Printer: HP Printer (HPLIP), and entered: hp:/net/HP_Color_LaserJet_CP3505?ip=192.168.2.60. Either method I use I am able to share the printer on the network by adding a printer as http://192.168.2.2:631/printers/HP_LASER-TERRAC. Does it make a difference which way the printer is added cups? If so, and I install the printer with the hp URI, can I still change the driver using the CUPS web interface? I have been trying out different drivers to try and improve performance, and the cups interface is the easiest way to change them. Thanks in advance.

  Read the article

• Routing Essentials

  - by zharvey

  I'm a programmer trying to fill a big hole in my understanding of networking basics. I've been reading a good book (Networking Bible by Sosinki) but I have been finding that there is a lot of "assumed" information contained, where terms/concepts are thrown at the reader without a proper introduction to them. I understand that a "route" is a path through a network. But I am struggling with visualizing some routing-based concepts. Namely: How do routes actually manifest themselves in the hardware? Are they just a list of IP addresses that get computed at the network layer, and then executed by the transport? What kind of data exists in a so-caleld routing table? Is a routing-table just the mechanism for holding these lists of IP address (read above)? What are the performance pros/cons for having a static route, as opposed to a dynamic route?

  Read the article

• Windows Server 2008 R2 DNS Server not working?

  - by wolfvilleian

  I have a server running Windows Server 2008 R2 hosting a DNS server, exchange 2010 and is a domain controller. One computer on the network (and domain) can ping the server 25% of the time, also when I try to ping it's own hostname it also does not work. However another computer that is on the domain can ping it fine, and another computer on the network but not domain can ping fine as well. The computer that cannot ping the server is setup to use the DNS server running on the server only (secondary dns points to nothing) and it will resolve the hostname of the server to the external IP not internal when the other two computers correctly resolve the internal All 3 computers and server are connected directly into the same switch. Does anyone have any ideas on how to fix this? Thanks

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the Internet via Eth0. Has one wireless network adapter and one another ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration.

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the internet via Eth0. Has one wireless network adapter and one more ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration

  Read the article

• Access my mac's local server from a windows machine

  - by Simon Davies

  I am running my test sites on my mac, but I would like be able to use my windows machine to also access this server and be able to write / read fiels form this server. I can access my sites on my windows by using the IP address 192.168.1.???. But I would like to be able to use my windows machine to also access the fiels and edit them. Any ideas much appreciated. Some details: Mac OSX SL file sharing set to on. Windows 7 (tried setting up network map using afp://192.... but nothing) Both machines are connected to a local network, with several other machine (windows) Thanks

  Read the article

• How do I set zone priority in Microsoft DNS?

  - by Justin

  I have a standard small network setup (20 users) on Active Directory. All Windows machines have a primary DNS server as the AD and a secondary DNS server as Google PDNS. I want to setup a DNS entry that exists in real DNS but set it up on our DC so that local requests would route this public domain to a local development machine on the network. I setup the zone in DNS which results in the clients resolving the public FQDN to our internal IP. However, sometimes it still resolves to the "real" value (I check by pinging it). Is there some way to give the zone definition in my DC DNS higher priority? Or will the client that has secondary public DNS always at sometimes have a competing entry for this zone?

  Read the article

• Configure IIS 6 to deny access to specific file based upon IP address

  - by victorferreira

  Hello guys, We are using IIS 6 as our webserver. And we need to deny the access for one specif file, placed in only one specific URL, to everybody OUTSIDE the local network. In other words, if somebody is trying to access that filme/page from their own computer at home, using the internet, they must not succeed. But, if the same person try to do that at the same network of the web server, its ok. I am not sure about that, but Apache uses ORDER DENY,ALLOW. You specify the URL, allow or deny to all or to a range of IP. Any suggestions? Thanks!

  Read the article

< Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >