Search Results

Search found 69096 results on 2764 pages for 'theoretical problem'.

Page 346/2764 | < Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >

• CentOS Installation on a Cisco MCS 7800

  - by William

  I'm having some problems installing CentOS 5.5 Final (i386) onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up and gives you the option on how to boot into the DVD, I'll press enter to go into the graphical installer. The screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours). I then booted into it again and tried using Linux Text thinking it was a problem with the graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point I think it's a hardware problem. The server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) configured for RAID 0. (There is also an option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. Edit Typing "text" doesn't change a thing. Still stuck at the blinking cursor. I looked it up and it's really the same thing as typing "linux text", which as stated in the first part of my question, I've already done.

  Read the article

• my laptop wireless registers as 169.254.111.111

  - by Roalt

  I sometimes gets an ip address of 169.254.111.111 received for my laptop (instead of one in the 10.0.0.x range). I thought it was a problem with my Ubuntu system, but after I dual-booted I got the same problem under Windows Vista with the same laptop. What's the problem, why does it happens only sometimes, and how can it be solved? For the record: I'm using a Linksys WRT610N wireless router.

  Read the article

• SBS 2003 boot stalls at acpitabl.dat

  - by John

  I have a SBS 2003 server running for 3 year without any problems, and few days ago it freezes during the boot. System is using two 500 Gb drives in RAID1 (Intel Matrix 7.5) After trying to load in safe mode, boot stops on acpitabl.dat. First idea was that there is a problem with RAID altough disk status was OK, and RAID status was Rebuild. I tried to boot with each drive, and one gives me the same problem, and the other drive is failing to load. Took both drives out, and checked it on a different machine. One drive is dead, other is without any problems. Returned the good drive back in SBS 2003 with changed status to Degraded, but the problem is still the same. I also have a clean SBS 2003 copy installed on this drive (previous installation), which loads smooth and quick. So, I believe the main problem is this installed version of SBS 2003. Did not make any hardware changes, did not make any updates (not sure about any automatic windows updates lately). Since there are tons posts about this problem, and no clear solution, I am trying to figure how to repair SBS 2003 installation, since there are some installed programs on this installation which I cannot re-install without additional issues.

  Read the article

• Vista laptop won't connect to airport extreme

  - by Hutch

  Our previous router died, and to replace it I procured an apple airport extreme. My mac, my wrt54gs (with ddwrt acting as a bridge) and a linux machine have had no problem connecting to the wireless. None of the wired clients are having a problem obviously. The problem is one of my roommates can not connect. That's not strictly true. He can connect to the network, and will, infact, get a dhcp lease. However he cannot get any packets out. Can't ping the router, can't access any web sites, nothing. However he's fine if we switch to an unsecured network. Which is obviously not acceptable. The airport only allows for 'wpa/wpa2 personal' and 'wpa2 personal' (and of course the enterprise versions there of) I keep reading about this problem in multiple spots on the web, but never see any actual answers... Anyway the laptop: hp/compaq cq50-215nr vista home premium wireess card: atheros 5007 airport is simultaneos dualband II

  Read the article

• System says memory controller not available and doesn't boot?

  - by Martin

  Hello everybody, Recently I have had a MainBoard-problem. I've send my mainboard to service and today I got it back from the company. It is a Foxconn 520a mainboard. Now I have installed my exchanged mainboard. But now I have a problem. My system boots until the device list with IRQ entries appear. The system says "Verifying DMI-pool-data..." and nothing happens. The IRQ-device list shows that the memory-controller is not available. All other devices have got an IRQ. Bus No. Device No. Func No. Vendor/Device Class Device Class IRQ 0 0 0 10DE 0547 0500 Memory Controller NA Do you have any ideas where the problem could be? I already have disconnected all unnecessary devices like the hard disks. Perhaps it is a BIOS problem, but I don't know where I should look. Would be nice if there is any advice, Greetings, Martin

  Read the article

• Stop the constant random reboots of my GIGABYTE GA-B75M-D3V

  - by Frederic

  I've got some issues with a new system. It's rebooting constantly. The system consists of a: brand new: Gigabyte GA-B75M-D3V with F9 BIOS (latest) Intel Core i5-3470 Ivy Bridge 2x 8GB G.SKILL Ripjaws 1600MHz memory (mem-tested x-86) coming from a stable system: Creative Soundcard X-FI Titanium Asus Radeon HD4850 OCZ Vertex 3 120G SSD Sata 3 Hard disk 1TB Sata 2 ASUS Blu-ray Drive PSU 400w Connected peripherals : Toshiba tv (displayport on dvi of MB or HD4850) Wired mouse, wireless keyboard (logitech) Bluetooth usb key Azio main problem : it's not possible to read the errors from the MB. nothing on the manual neither on internet. At the beginning, I received a MB with graphic problems and the problem of rebooting. I RMA'd it. The new one doesn't have any graphic problems. but it's still constantly rebooting. I removed everything except the HD, the sound-card, the blu-ray drive and the wireless keyboard. It's still unexpectdly rebooting. I'm running a test with just the motherboard and the HD. I will update this text after the test. I've got some questions : Somebody have an idea of a test? The PSU could cause that problem? I used it a lot of years with the stable system. Update 1: BTW, if anyone has the same problem, the manual won't say it but you'll need to reset the bios between two tests (the screwdriver on the two pins) if you suspect a problem of compatibility .

  Read the article

• Netbook (Samsung N220) on Ubuntu 10.04 slows down WiFi for other computers

  - by Joachim

  I encountered a really odd problem with my new netbook. I am running Ubuntu 10.04 on a Samsung N220 Mito. So far everything worked fine. Now I tried the machine for the first time in our work group where we have a wifi (with internet access) for all laptops. The wifi is controlled by a computer running Suse 9.3 which provides a DHCP server and imposes a firewall. At the moment there is only a macbook in the wifi, where no problems with the internet or wifi connection are encountered. Now coming to my actual problem: In addition to the macbook i connect the Samsung N220 to the Wifi. Problem: My download speed is for some reason limited to 70KB/s max. This is neither a limitation of the server/website i browse on, nor a configuration of the netbook: at home i have 500KB/s download speeds. Furthermore, it is not a default limitation for "untrusted" or "new machines" in the wifi, as for instance other new laptops get full speed internet with our wifi. Problem: Once the Samsung N220 is generating traffic in the wifi, the wifi is slowed down dramatically for all other machines: I run a ping to the router from the macbook. The ping times with the N220 ideling are 2-6ms. When I start downloading or browsing in the web with the N220 the ping speed drops to 800ms. Vice versa, when the macbook is generating the traffic the ping of the N220 to the rooter stays constant at around 2-6ms. So clearly, it is some problem originating from my netbook or maybe its treatment in the wifi. Thanks for any help

  Read the article

• MicroSD card getting corrupted for no good reason

  - by ChaosR

  I recently bought an MicroSD card online. It's a Sandisk 16GB class 2. However, it has a nasty problem. Every time I fill it with my data, the fat tables get corrupted. I've tried reformatting it, blanking it, doesn't seem to solve the problem. I have tried windows and linux (ubuntu), both have the problem. I've used my usb microsd readers, and even tried putting it in my phone and putting data on it from there. All have this problem. Now the really odd thing is, besides the corrupted file tables, no programs can find anything wrong with the hardware. I've tried both chkdisk and "badblocks -w", neither give any type of error. Now I don't know if the actual data gets corrupted, or if its just filesystem tables. What happens is that one or more folders start showing a load of chinese-charred (random UTF8 symbols I suppose) folders and files, and it is impossible to do anything with those. All the other data (outside of the corrupted folders) seems fine. I've tried to test it, and the problem doesn't seem to show up until I fill the disk upto about 3~4GB. After that I can still access the data. But as soon as I eject/safely remove/unmount it, the bad things happen somehow. Next time I plug it in, the folders I most recently wrote to (but sometimes also the folders I wrote the time before last time to) are all gibberish. Does anybody have any clue what might be going on here? EDIT: It seems I can't even put ext3 or ext4 on it, they both complain about a corrupted journal. Gheh, guess something is really broken here.

  Read the article

• cant access site intermittent as i get site not available

  - by user61438

  i have a news site i check stuff for regularly.. once in a while i cant access it completely from my 5 different browsers and even from the command line, nslookup cant resolve, ping and tracert fails.. all not being able to resolve site name..the problem is specific to this.. i am told by the site support person that problem is that its cache on my machine or on ISP and I say thats not true because this site I access it 1-2-3 times a week from one browser only.. i only fire up the other ones in times of trouble..and when i have the problem even if i try on my secondary machines i still get the same problems.. when problem goes away all works well.... question is whats causing the intermittent dns/http problems... i don't believe this is something to do with my machine because probe disappears without me having done anything at all.

  Read the article

• what's the reason that two antiviruses cannot scan the computer together properly?

  - by Ehsan Mamakani

  what is the reason for this problem?

  Read the article

• Getting spurious undo (ctrl-z) sent randomly on a Dell Laptop

  - by squelart

  For the past couple of weeks, my laptop has had a strange problem where it looks like ctrl-z is pressed, so I usually lose bits of text I just typed. If I press ctrl-shit-z (redo), the text comes back, proving it's really as if ctrl-z was pressed. It's difficult to see a pattern, I can be undo-free for hours, then get a few within minutes, sometimes 2-3 undoes at a time. Very frustrating! Running WinXP+SP3 on Dell Latitude D820, Clamwin antivirus. I've tried another keyboard, no difference. Any clue on what this could be, or how I could trace this problem? 2009-09-25: Tried a few things that were listed or linked to on this page: http://www.selfishman.net/2008/06/24/problem-with-dell-inspiron-1501-keypress-every-second/ but nothing helped. Though it seems to point at a Dell laptop issue. I upgraded the BIOS and other drivers, but still got the problem.

  Read the article

• Explorer.exe keeps crashing during log in

  - by asif

  I have got a weird problem. My windows 7 has two user accounts (both are administrator). I can log in to one account and do all sort of work. But whenever I try to log in to other account, it shows a blank screen and a messagebox pops up with "windows explorer has stopped working". The options available are: Close the program Check online for a solution and close the program The problem signature is as follows: Problem Event Name: InPageError Error Status Code: c000009c Faulting Media Type: 00000003 OS Version: 6.1.7601.2.1.0.256.1 Locale ID: 1033 Additional Information 1: 0a9e Additional Information 2: 0a9e372d3b4ad19135b953a78882e789 Additional Information 3: 0a9e Additional Information 4: 0a9e372d3b4ad19135b953a78882e789 If I press alt+ctrl+del and then select start task manager, it also crashes. I can not run any program using runas command (from good profile) too. The task manager and runas programs all show same problem signature. I read the similar question and followed all the steps, but no luck. Later, I viewed the event log and found that, explorer.exe could not access a file. I checked the location but the file is there. The actual message is: Windows cannot access the file C:\Users\testuser\AppData\Local\Microsoft\Windows\Caches\{AFBF9F1A-8EE8-4C77-AF34-C647E37CA0D9}.1.ver0x0000000000000020.db for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program Windows Explorer because of this error. The question is, how can I resolve this issue? Should I just delete the file or replace it with another one to stop explorer.exe from crashing? offtopic: What is the content of this file and why it is necessary?

  Read the article

• Local Apache on Windows XP not finishing page requests

  - by asgeo1

  I have Apache 2.2.11 installed locally on my Windows XP (SP3) dev machine, which I setup about 3 months ago. I have just started having a strange problem in the last few week. Apache is serving some basic PHP applications like phpMyAdmin. When I make a page request, Apache appears to not finish serving all resources for that page. Firefox shows the "Transferring data from servername..." message, and the page never completes. The same problem happens in Internet Explorer too. I can sometimes tell which resource it is waiting on, because most of the page will render except for some image or similar resources. (Not sure why Firebug doesn't show this) It doesn't have the problem every page request - for page requests where most of the resources are cached in my browser, the page request will work with no problems. Or pages that are very light will work with no problems. However, if I "hard" refresh the page, I will have this problem (probably because it is requesting all page resources) Does anyone know what this could be? It is so strange that it has only just started happening - and I did not make any changes to my system (that I am aware of) I tried playing with the Apache ThreadsPerChild setting, but it did not seem to make a difference. UPDATE: I have been doing some more tests. I have been serving the most basic of pages, just a plain HTML file: <html> <body> <h1>testing</h1> </body> </html> If I request this page multiple times in a row, AND each request occurs immediately after the previous has completed, then 50% of the time the request will time out. However, if I put a 1-2 second gap between requests, then there is no problem. This correlates to what I have observed when the brower requests a real application page. When the browser has nothing cached, then all of the page resources are requested from the browser in a short amount of time - this appears to trigger the problem. UPDATE2: Nathan Long has helped me understand the issue a little better with the server-status page (see below). It is weird, it is like the server has a hickup sending data to the client. The client sits there waiting forever for data that never arrives. Closing the client process does not terminate the connection on the server - the server still has active threads for each previously attempted connection, but they just sit there - not sending any data and never terminating. (even though the client is now closed) Only a restart of the server seems to terminate them.

  Read the article

• Troubleshooting an NFS server hanging after authenticated mount request

  - by Christoph

  I need some advice on troubleshooting an NFS server problem on Scientific Linux (RHEL) 6.1. The log on the server shows that an authenticated mount request was made: Jan 13 16:30:02 ??? rpc.mountd[3996]: authenticated mount request from ????:784 for /shared-storage/cm/shared (/shared-storage/cm/shared) But after that, it does not continue. On the client, it is also hanging. The interesting thing now is that I have two NFS servers, which should be identical, and the one is working perfectly, but the other exhibits the above mentioned behaviour. The problem is also not completely persistent, i. e. sometimes the mount request succeeds. I assume that the problem must be related to the server rather than to the client, because it is working perfectly on the other server. My question is where I should search the problem. I have already re-created the exports using exportfs -r, I have restarted the NFS server, I have compared the rpcinfo outputs of both server - no success. The problem even survives a reboot. Any other ideas are appreciated. As answer to Tim's question: I have sporadically the following in dmesg, but do not know whether it is related e1000e 0000:0c:00.0: eth4: Detected Hardware Unit Hang: TDH <24> TDT <25> next_to_use <25> next_to_clean <24> buffer_info[next_to_clean]: time_stamp <1c3d12940> next_to_watch <24> jiffies <1c3d12940> next_to_watch.status <0> MAC Status <80383> PHY Status <792d> PHY 1000BASE-T Status <7800> PHY Extended Status <3000> PCI Status <10> Further edit: The problem above does not occur on the machine that is working, so it probably is related. Again an edit: The error is not on the (software) device that is used for NFS, but on another one. The NFS mount also does not trigger the message.

  Read the article

• Problems with Windows Server 2012 Hyper-V

  - by user3438673

  I install a windows server 2012 R2 and then install a virtual machine on hyper-v. When i configure the virtual machine in hyper-v i configure 4gb of ram then few days later y change it to 12gb of Ram Problem the problem is when i change the ram the virtual machine star working slower and i have to return the 4gb of ram. i cretae a new virtual machine and i configure the virtual machine with 12gb of ram from start but still working to slow do you know how to solve this problem in hyper-v?

  Read the article

• Windows 7 connect to Lion file sharing

  - by McKvack

  Trying to access my Mac from a Windows 7 computer, I fail with the infamous error 86 incorrect password. Now this appears to be a well-known problem with countless threads on the internet giving as many "solutions" as there are discussion threads about it (mostly ranging from installing third-party commercial samba servers, to switching to some other protocol, to compiling a plain-vanilla Samba installation - the latter which I will probably do when I give up this :) ) I am stubborn, and I believe there must be some problem here that can be solved or worked around, but there is surprisingly little detail about this problem. It appears to have something to do with a mismatch of authentication methods. Trying to run samba in debug mode: sudo /usr/sbin/smbd -debug -stdout gets me this output when trying to access it from Win 7 ... smb1_dispatch_one [smb_dispatch.cpp:377] dispatching SMB_COM_SESSION_SETUP_ANDX smb1_dispatch_session_setup [session_setup.cpp:261] FIXME erase existing sessions log_gss_error [gssapi_mechanism.cpp:97] gssapi: gss-code: Miscellaneous failure (see text) log_gss_error [gssapi_mechanism.cpp:113] gssapi: mech-code: unknown mech-code 22 for mech unknown What is the problem here, and how do I fix it?

  Read the article

• Debian Linux server hangs after a week or so

  - by Alex Flo

  I have 2 Debian Linux 6.0.4 servers that have a strange behaviour: after 5-7-10 days they hang. By this I mean the servers need to be restarted and before that ping won't answer. I've been struggling with this problem for a couple of months now and here's some thoughts/what I tried without being able to solve the problem. I changed the RAM on a server. Being 2 different servers I doubt that it could be something related to hardware as a 3rd identical server won't have this problem. I logged the server load and when it crashes the load is fine (quite low) I cannot find anything in the server logs, logs are fine till the server freezes. I don't have access to console unfortunately. While I have years of admin experience I have never encountered such an issue and right now I have no idea where else to investigate. If you have an idea of what I could try in order to fix the problem please share it with me:-)

  Read the article

• WS2008 subst in Logon script does not "stick"

  - by Frans

  I have a terminal server environment exclusively with Windows Server 2008. My problem is that I need to "map" a drive letter to each users Temp folder. This is due to a legacy app that requries a separate Temp folder for each user but which does not understand %temp%. So, just add "subst t: %temp%" to the logon script, right? The problem is that, even though the command runs, the subst doesn't "stick" and the user doesn't get a T: drive. Here is what I have tried; The simplest version: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") WinShell.Run "subst T: %temp%", 2, True That didn't work, so tried this for more debug information: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") Set procEnv = WinShell.Environment("Process") wscript.echo(procEnv("TEMP")) tempDir = procEnv("TEMP") WinShell.Run "subst T: " & tempDir, 3, True This shows me the correct temp path when the user logs in - but still no T: Drive. Decided to resort to brute force and put this in my login script: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") WinShell.Run "\\domain\sysvol\esl.hosted\scripts\tempdir.cmd", 3, True where \domain\sysvol\esl.hosted\scripts\tempdir.cmd has this content: echo on subst t: %temp% pause When I log in with the above then the command window opens up and I can see the subst command being executed correctly, with the correct path. But still no T: drive. I have tried running all of the above scripts outside of a login script and they always work perfectly - this problem only occurs when doing it from inside a login script. I found a passing reference on an MSFN forum about a similar problem when the user is already logged on to another machine - but I have this problem even without being logged on to another machine. Any suggestion on how to overcome this will be much appreciated.

  Read the article

• How can I avoid a few seconds of blank video when using -vcodec copy?

  - by arlomedia

  I'm processing user-uploaded videos on a CentOS web server with ffmpeg. I need to convert each video to a standard size and format, then extract a 30-second sample clip from each video. I want to use the "-vcodec copy" flag in the extraction command to avoid encoding a second time. This command works for my initial conversion: ffmpeg -i uploaded.mov -f mp4 -vcodec libx264 -vpre medium -acodec libfaac -r 15 -b 360k -ab 48k -ar 22050 -s 480x320 formatted.mp4 And this sometimes works for the extraction: ffmpeg -i formatted.mp4 -vcodec copy -acodec copy -ss 0 -t 30 formatted_sample.mp4 However, when I run the extraction command on some videos, the extracted sample clip starts with several seconds of blank video. The audio starts right away but the video doesn't start for 3-6 seconds. To demonstrate the problem, I've uploaded two video clips and run the above commands on them. I created the first clip in Final Cut Express and encoded it with Handbrake before uploading to the web server: 1a) uploaded clip 1b) converted with first command 1c) extracted with second command, missing first six seconds By comparison, this second clip comes from Apple's website and does not show the problem: 2a) uploaded clip 2b) converted with first command 2c) extracted with second command, no problem Can anyone see what's different about the two source clips? And if so, is there anything I can do in my conversion command so that when the extraction command runs, the clip is set up to avoid the missing video? By the way, I initially had the problem with ffmpeg 0.6.1 installed from yum, but I upgraded to the latest git version and the problem remains.

  Read the article

• Ubuntu Server login not recognizing the keyboard after entering username.

  - by Jeff Malewski

  I'm having similar issues with logging into ubuntu server. chief problem is that once I enter my user name & hit enter, I can't enter anything ffor my password - it won't accept any keystrokes until I press Ctrl+any key. Once I've pressed Ctrl+ any key, I'm able to type again, but have never been able to enter any more than 3 characters before the 60 sec time limit. This problem is present on fresh installs of both 10.04 & 9.10. Part of the problem is lkely to be my antique pc which is an old Emachines Trigems I850 based mbd and an equally ancient Nvidia 4x AGP video card. Initially I was going to install Ubuntu 10.10, but with ORCA running with both screen reader and full screen magnification crashed the system & smoked a stick of Rambus memory. Is there any fix to this problem? Jeff

  Read the article

• Linux wireless disconnect every 20 minutes

  - by james

  My laptop uses CentOS 6.3 with kernel 2.6.32-279.el6.x86_64. My wireless adaptor is Intel Corporation Centrino Wireless-N 1000. My wireless connection always get off after about 20 minutes. The network applet shows the connection is still on with good signal strength, but I just cannot load any web pages even the configuration page of the wireless router. The problem will continue until I disable and reconnect the wireless. Other devices like my cell phone uses the same wireless network without the problem. Even yesterday I'm using the same laptop with Fedora 17 without this problem. I also searched the internet and someone said running services NetworkManager and network simultaneously may be a problem. But I cannot stop any one of them because: if I stop network and start NetworkManager, the network service will start automatically; if I stop NetworkManager and run network, it says "Device does not seem to be present, delaying initialization." when trying to bringing on the wireless. What shall I do to get rid of the problem? Thank you very much!

  Read the article

• 'Bug in Mailman version 2.1.12'

  - by davorg

  I'm working on setting up a server running Plesk 10.4.4 Update #13 on Centos 6.2. I've configured Mailman and now I want to set up some mailing lists. I've created a list in the Plesk control panel, but when I try to administer the new list (by visiting http://lists.[domain].com/mailman/admin/[listname] I see the following error: Bug in Mailman version 2.1.12 We're sorry, we hit a bug! Please inform the webmaster for this site of this problem. Printing of traceback and other system information has been explicitly inhibited, but the webmaster can find this information in the Mailman error logs. I see exactly the same error if I try to go to the list info page at http://lists.[domain].com/mailman/listinfo/[listname]. I would follow the instructions and look in the error logs, but I can't find them. I would expect to find a file at /var/log/mailman/error, but there's nothing there. My test list seems to work correctly. It sends all the expected email. It's just the web pages for the list that seem to be broken. Has anyone else seen this? Any suggestions for tracking down and fixing the problem? p.s. I think I've chosen the correct Stack Exchange site, but it this question would be better asked elsewhere, please let me know. Update: I got to the bottom of this, so I'm documenting the answer in case anyone else has the same problem. The fact that I couldn't find the error log was the clue. The problem was that the Mailman process didn't have permissions to create an error log. And it seems that if Mailman can't create an error log then it will respond to any web request with this error page. Creating an error log file (in /var/log/mailman/error) and giving it the correct permissions fixed the problem.

  Read the article

• Save a single web page (with background images) with Wget

  - by mikael

  I want to use Wget to save single web pages (not recursively, not whole sites) for reference. Much like Firefox's "Web Page, complete". My first problem is: I can't get Wget to save background images specified in the CSS. Even if it did save the background image files I don't think --convert-links would convert the background-image URLs in the CSS file to point to the locally saved background images. Firefox has the same problem. My second problem is: If there are images on the page I want to save that are hosted on another server (like ads) these wont be included. --span-hosts doesn't seem to solve that problem with the line below. I'm using: wget --no-parent --timestamping --convert-links --page-requisites --no-directories --no-host-directories -erobots=off http://domain.tld/webpage.html

  Read the article

• Where to download replacement "Explorerframe.DLL" Files for x64 Windows 7 Pro?

  - by Ben Franchuk

  After posting this question, I did some research to reveal what the problem likely was, and found what I need to fix. Following this is the original post, then my updated question. A few months ago I ended up requiring to change my computer's SID to fix a problem it had been having- Instead of fixing the problem, though, it screwed up my at-the-time current install of windows, to the point of me needing to do a fresh install. As I am in possession of an OEM copy of Windows 7 Pro 64 Bit, I successfully reinstalled over the dead copy with that (all the files that were on the computer previous to this windows install were put in a Windows.old folder). Everything installed and worked absolutely fine, except for one thing. The problem I am experiencing is that, in some Windows Explorer windows, the explorer pane doesn't show. Instead, it simply shows a white area where the pane would show. This makes some software not usable, I recently realized; Software such as Cubase, which use just the explorer pane to select file save locations, cannot save at all as the pane itself is... not operational. Below is a screenshot of this problem as it occurs in cubase; ...and again as it shows in UTorrent in the save location selector window. The highlighted area is where the sidebar would NORMALLY be. Pardon my scribbling over some of the things in the window- I would personally rather the internet did not get a glimpse of my files. I have yet to find a common reason why the pane works in some applications when they pull explorer, and others not. I have yet to see it go away, and the software affected by it has been affected since I reinstalled my copy of windows. Initially, I was able to live with it as I can type out save locations in the file name bar to navigate, but with software like Cubase, I do not have this option. Reinstalling windows again is NOT an option. Here's the updated question. After posting this question originally, I did some research on the problem in question, and it turns out that this is extremely easily fixable via replacing the file "ExplorerFrame.DLL" which is located in the System32 and SystemWOW64 Folders, in the windows folder, on the C:\ drive. As I quite frequently customize my computer, this is a normal thing for me to do and I know exactly how to safely and properly replace this file. The only problem is that I cannot for the life of me find a download of this file that actually works with my computer. I tried a couple from some different sites but they all caused explorer to not restart (I was given an error when starting the application from Task Manager) and was forced to revert to the broken .DLL files. Since there are 2 separate "ExplorerFrame.DLL" files; one for 64 bit and the other for 32 bit, I am assuming that I will need to download 2 separate versions to replace the corrupted ones. Where can I acquire these files? I am currently running Windows 7 Professional x64 Bit.

  Read the article

• How to stop Firefox on an SSD from freezing when using the search box or submitting a form?

  - by sblair

  Firefox usually freezes for about a second whenever I search for something from the toolbar search box, when submitting a form, or when clearing the search box history. I suspect it has something to do with the auto-complete feature. Using Windows 7's Resource Monitor, the problem seems to be from the file: C:\Users\<username>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\formhistory.sqlite-journal I believe this is a temporary file which caches database writes. The following screenshot shows the very high response times from six different searches, and that the queue length on drive C shoots off the scale: My Firefox profile is on an Intel X25-M G2 SSD. The problem doesn't seem to occur if I create a new profile on a hard disk drive. However, I'd like to know why the problem exists on the SSD in the first place (because it's an annoying problem which contradicts the reason I bought an SSD, and it might happen with other applications too), and how to prevent it. It still occurs if Firefox is started in safe mode, and with the recent beta versions. Updates: VACUUMing the Firefox profile databases does not help with this problem. The SSD Optimizer in the Intel SSD Toolbox does not help either.

  Read the article

< Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >