Search Results

Search found 11482 results on 460 pages for 'portable device'.

Page 347/460 | < Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >

• Ubuntu 12.04 wireless disabled even though the direct connectin (thru modem) is working fine

  - by user90841

  Need help with my newly installed Ubuntu 12.04 system (dual booting along with Win 7), even thoguh I can use internet using the modem and directly plugging it, the wireless network is disabled and it says firmware missing. I tried the following options: 1) checking to see if the wireless is disabled using the hot keys (F2 or Ctrl+F2, Fn + F2 keys), the wireless is working fine in Win 7 but not in Ubuntu. 2) I am able directly plug the laptop with the modem and able connect to Internet using Ubuntu. 3) From the top right hand menu bar, te Wireless networks options say "device not ready (firmware missing) and the Enable Wireless checkbox is checked. 4) tried the command "rfkill list" , it shows all are NOT blocked. 0: phy0: Wireless LAN soft blocked:no Hard blocked: no 1: dell-wifi: Wireless LAN soft blocked:no Hard blocked: no 2: dell-bluetooth: BlueTooth soft blocked:no Hard blocked: no 3: hci0 Bluetooth soft blocked:no Hard blocked: no 5) ifconfig command shows eth0 and lo (lcoalhost) up and running but the wlan0 option is not available to show unless I type ifconfig -a, when it shows wlan0 but its down. 6) The command lspci -vvnn | grep 14e4 shows 04:00.0 network Controller [0280]: Broadcom Corp BCM4312 802.11b/g LP-PHY [14e4:4315] {rev 01) 08:00.0 Ethernet Controller [0200]: Broadcom Corp Netlink BCM5784M Gigabit Ethernet PCIe [1434:1698] {rev 10) 7) The file /var/lib/NetworkManager/NetworkManager.state shows all options are true (networking enabled, wireless enabled, wwlanenabled and wimaxenabled all options are set to true). 8) 'additional drivers' in your Dash and/or Preferences do not bring up anything at all. 9) output for lshw -C network shows *-network DISABLED description : Wireless interface physical id: 4 logical name: wlan0 serial: 78:e4_00"43:b6:ab capabilities: ethernet physical wireless Configuration: broadcast=yes driver=b43 driverversion=3.2.0.29-generic-pae firmware=N/A link=no multicast= yes wireless=IEEE 802.11bg

  Read the article

• 13.04 Temp Save, rt3290, Kernel downgrade

  - by user170534

  It's kind of a multiplying but I didn't wanted to open more than one topics. I'd have a fresh install of Ubuntu with tlp configured and using acpi_call to keep 7670M turned off. I was a short time arch user and with openbox and firefox it was about 60 to 70 degrees; wanted to turn to a stable release just for this reason. acpitz-virtual-0 Adapter: Virtual device temp1: +50.0°C radeon-pci-0100 Adapter: PCI adapter temp1: -128.0°C coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +56.0°C (high = +87.0°C, crit = +105.0°C) Core 0: +54.0°C (high = +87.0°C, crit = +105.0°C) Core 1: +55.0°C (high = +87.0°C, crit = +105.0°C) The temperature is not seriously high yet can be lower. Another issue is my wifi card, rt3290: The rt2800pci module is fine and all that but the download performance is pretty bad alongside of annoying signal range and the prop. driver gives a conf error about some specific rt2860 code and integrales in pci_dev file. If I blank off the error making variables, module loads but the driver is unused. Since the driver is old, I was thinking of downgrading the kernel of raring to 3.7 or may be 3.6. Should &-or can I?

  Read the article

• Reverse-Engineer Driver for Backlit Keyboard

  - by user87847

  Here's my situation: I recently purchased a Sager NP9170 (same as the Clevo P170EM) and it has a multi-colored, backlit keyboard. Under Windows 7, you can launch an app that allows you to change the color of the backlighting to any of a handful of colors (blue, green, red, etc). I want that same functionality under Linux. I haven't been able to find any software that does this, so I guess I'm going to have to write it myself. I'm a programmer by trade, but I've haven't done much low level programming, and I've certainly never written a device driver, so I was wondering if anyone could answer these two questions: 1) Is there any software already out there that does this sort of thing? I've looked fairly thoroughly but haven't found anything applicable. 2) Where would I start in trying to reverse engineer this sort of thing? Any useful articles, tutorials, books that might help? And just to clarify: The backlighting already works, that's not the problem. I just want to be able to change the color of the backlighting. This functionality is supported by the hardware. The laptop came with windows software that does this and I want the same functionality in Linux. I am willing to write this software myself, I just want to know the best way to go about it. Thanks!

  Read the article

• Mobile web app, styling in percentages; I can't get height to work [migrated]

  - by Mick79

  I am building a mobile app for a band and obviously want it to display well in all the plethora of handsets out there today. I built it at first for my own device and it looks and works great, so now I am reworking it in percentages so that it works in all devices. I have a slider (jquerytools) going on and if i set width to 100% then it is perfectly wide in my iphone and my ipad... success, however I am not having any luck with height. It seems to only accept a height in px. If i set a height in percent it just doesn't display. any ideas? #header{ width:100%; height:198px; position:relative; z-index: 20; box-shadow: 0 0 10px white; } .scrollable { /* required settings */ position:relative; overflow:hidden; width: 100%; height:100%; box-shadow: 0 0 20px purple; z-index: 20; } .scrollable .items { /* this cannot be too large */ width:500%; height:100%; position:absolute; clear:both; box-shadow: 0 0 30px green; } .items div { float:left; width:20%; height:100%; } /* single scrollable item */ .scrollable img { float:left; width:100%; height:100%; /* height:198px; */ } /* active item */ .scrollable .active { border:2px solid #000; position:relative; cursor:default; } `

  Read the article

• I have Ubuntu only and need to install Windows

  - by Terzuz

  I had Windows 8, I installed Ubuntu for a new OS, Then I want to sadly go back to Windows , I have a Windows Vista *.iso but I can't boot from it. When I try to extract the '.iso file and have the contents on my USB so it can boot up , When I restart and click F9 for my Boot Device Options , Only my Hard Drive and CD ROM are there but my "Generic Flash Drive" is not , But when I do not have Windows Vista '.iso on it , It will show up in the list. How can I make a partition of some sort, Provide instructions since I am new at this all , then I need to be able to use the Windows Vista installer and install Windows Vista, I would like Dual-Boot if possible. Info: I have the HP 2000 Laptop (Mine was removed from the Best Buy Website so the closest laptop to the specifications and the design is the link at the bottom) I am running Ubuntu 12.10. I have 4GB of RAM , 220 GB in my Hard Drive left , I have a USB Flash Drive which works sometimes , other times it fails. Note - I tried using GParted in Ubuntu but I had a problem where the main drive with 220 GB Free was locked , I am not sure what to do and can not find the correct forum. http://www.bestbuy.com/site/HP+-+Pavilion+15.6"+Laptop+-+4GB+Memory+-+320GB+Hard+Drive+-+Pewter/5043836.p?id=1218608951204&skuId=5043836

  Read the article

• Which hard disk drive is which?

  - by djeikyb

  I want to know which hard disk drive corresponds to which device path. It's trivial to match the hard disk stats (brand, size) with the dev path, but I want more. I want to know which drive is which inside my case. What's a good way to go about getting this info? Rules: I am a lazy bum. I don't want to tear apart my server to remove all the drives, then add back one by one. A reboot is acceptable. The drives are inconveniently scrunched together in the case. All label information is hidden. The case can be opened. Most disks are SATA, so theoretically hot swappable. Unplugging cables is fair game. Bonus: For a cli only solution. I'll award answer to the best/easiest gui or cli answer, and give a bounty to the next-best answer of the other kind. Or maybe the other way around, because the bounty is worth more points.

  Read the article

• Algorithms for Data Redundancy and Failover for distributed storage system?

  - by kennetham

  I'm building a distributed storage system that works with different storage sizes. For instance, my storage devices have sizes of 50GB, 70GB, 150GB, 250GB, 1000GB, 5 storage systems in one system. My application will store any files to the storage system. Question: How can I build a distributed storage with the idea of data redundancy and fail-over to store documents, videos, any type of files at the same time ensuring that should one of any storage devices fail, there would be another copy of these files on another storage device. However, the concern is, 50GB of storage can only store this maximum number of files as compared to 70GB, 150GB etc. With one storage in mind, bringing 5 storage systems like a cloud storage, is there any logical way to distribute or store the files through my application? How do I ensure data redundancy through different storage sizes? Is there any algorithm to collate multiple blob files into a single file archive? What is the best solution for one cloud storage with multiple different storage sizes? I open this topic with the objective of discussing the best way to implement this idea, assuming simplicity, what are the issues of this implementation, performance measurements and discussion of the limitations.

  Read the article

• How to integrate Java ME SDK 3.2 with Eclipse

  - by SungmoonCho

  Here is also an instruction on how you can integrate Java ME SDK 3.2 with Eclipse. You need additional steps for Eclipse Juno, because it does automatically detect and download MTJ (Mobile Tools for Java) plugin. The following instruction is for Eclipse Indigo. 1. Download Java ME SDK and Eclipse plugins from here. 2. Install Java ME SDK 3. Launch Eclipse 4. Go to "Help" - "Install New Software" 5. Click "Archive", and choose the Eclipse Plugin zip file you downloaded. Name is something like "Java ME SDK Plugin" 6. Choose Java ME SDK Tools, and select "Next". 7. It will calculate requirements and dependencies. Simply follow the instruction. 8. You may also have to manually install the platform. Check out "Help" - "Preferences" - "Java ME" - "Device Management". If you do not see Java ME SDK 3.2 devices, click "Manual Install" on the right side, and specify the folder where Java ME SDK is installed. By default, it is installed at "C:\Java_ME_platform_SDK_3.2". 9. You're done. Now you can use the Java ME SDK plugins for Eclipse.

  Read the article

• Oracle Virtual Desktop Infrastructure

  - by Fat Bloke

  A lot of the recent blog entries here have been about Oracle VM VirtualBox, possibly the coolest personal desktop virtualization product known to man. Deploying VirtualBox on your PC or Mac lets you run many virtual desktops at the same time to one user, you. But did you know that VirtualBox can also power an Enterprise-scale virtual desktop deployment too, delivering many desktops to many users?  As part of another Oracle product, Oracle Virtual Desktop Infrastructure (VDI), VirtualBox can run your Windows, Linux or Solaris desktops on servers located in the datacenter. Oracle VDI orchestrates the whole deal by looking after : creating or cloning the virtual desktops from a master template; managing the lifecycle of the desktops (create, start, suspend, resume, stop, delete); assigning which users get which desktops;  delivering easy and fast access to these virtual desktops from almost any device, such as existing PCs or Macs, iPads, or specially designed Sun Ray client devices too; load balancing and session management of all of this.  Architecturally the solution looks something like this: This is an increasingly hot area of the IT landscape, so the Fat Bloke has decided to create a new blog category (VDI) and dedicate a few blog entries to look into this in a bit more detail over the next few weeks. Watch this space... - FB 

  Read the article

• Is it reasonable to null guard every single dereferenced pointer?

  - by evadeflow

  At a new job, I've been getting flagged in code reviews for code like this: PowerManager::PowerManager(IMsgSender* msgSender) : msgSender_(msgSender) { } void PowerManager::SignalShutdown() { msgSender_->sendMsg("shutdown()"); } I'm told that last method should read: void PowerManager::SignalShutdown() { if (msgSender_) { msgSender_->sendMsg("shutdown()"); } } i.e., I must put a NULL guard around the msgSender_ variable, even though it is a private data member. It's difficult for me to restrain myself from using expletives to describe how I feel about this piece of 'wisdom'. When I ask for an explanation, I get a litany of horror stories about how some junior programmer, some-year, got confused about how a class was supposed to work and accidentally deleted a member he shouldn't have (and set it to NULL afterwards, apparently), and things blew up in the field right after a product release, and we've "learned the hard way, trust us" that it's better to just NULL check everything. To me, this feels like cargo cult programming, plain and simple. A few well-meaning colleagues are earnestly trying to help me 'get it' and see how this will help me write more robust code, but... I can't help feeling like they're the ones who don't get it. Is it reasonable for a coding standard to require that every single pointer dereferenced in a function be checked for NULL first—even private data members? (Note: To give some context, we make a consumer electronics device, not an air traffic control system or some other 'failure-equals-people-die' product.) EDIT: In the above example, the msgSender_ collaborator isn't optional. If it's ever NULL, it indicates a bug. The only reason it is passed into the constructor is so PowerManager can be tested with a mock IMsgSender subclass.

  Read the article

• How do I add a boot from cd option to yaboot?

  - by Sergiu

  So I'm dual-booting Ubuntu 12.04.1 on my iMac G5 powepc alongside Mac OS X and I want to add a boot cd option to yaboot because I'm trying to boot a scratched Mac OS X installation DVD that takes a while to read and the frst bootstrap moves on too fast. How do I edit the timeout for the first bootstrap anyways? So, my main question is, how do I add a cd booting option to yaboot and then, how doI boot it? The devalias from OpenFrmware tells me that 1 have 2 cd-rom instaled, on is /ht/pci@3/ata-6/disk@0 and the other on ends with a 1 instead of a zero. These are the contents of my yaboot.conf file: yaboot.conf generated by the Ubuntu installer run: "man yaboot.conf" for details. Do not make changes until you have!! see also: /usr/share/doc/yaboot/examples for example configurations. For a dual-boot menu, add one or more of: bsd=/dev/hdaX, macos=/dev/hdaY, macosx=/dev/hdaZ boot="/dev/disk/by-id/scsi-SATA_ST3160023AS_5MT1GCWA-part2" device=/ht@0,f2000000/pci@3/k2-sata-root@c/@0/@0 partition=4 root="UUID=798a048f-ee48-49e0-bba3-111aed8dee04" timeout=12000 install=/usr/lib/yaboot/yaboot magicboot=/usr/lib/yaboot/ofboot enablecdboot macosx="/dev/disk/by-id/scsi-SATA_ST3160023AS_5MT1GCWA-part3" image=/boot/vmlinux label=Linux read-only initrd=/boot/initrd.img append="quiet splash" What do I add here so that yaboot will boot from my cd in like 3 minutes after startup? Thanks!

  Read the article

• USB Keyboard works occasionally

  - by palimmo

  A few days ago I bought a SL640 Hama USB keyboard to use on my laptop with Ubuntu 12.04. But I'm having problems, as it works one time out of 10! While on my girlfriend's laptop, with Win Vista, always works. And on my laptop I have Win7 in dual boot. And I have to say that it always works on it. Here are some infos: ~$ lsusb Bus 006 Device 003: ID 04d9:1503 Holtek Semiconductor, Inc. Shortboard Lefty As you can see, the OS recognized it but the keyboard doesn't react ... even the Caps Lock and Num Lock keys don't blink. Regarding the legacy support (useful for GRUB), I have found no entry in the BIOS. But I'm not interested in it. I just want to use it in Ubuntu. However, in GRUB it works sometimes. Surprisingly, now I have booted my laptop: the usb keyboard hasn't worked in GRUB but it has worked since the ubuntu login! And now I'm typing with it. Well.. it means that Ubuntu has the right drivers and they work. But how to "load" them always correctly? thanks in advance!

  Read the article

• One of my VMs went boom using Virtual Box and how it got fixed

  - by Enrique Lima

  I am running an HP Envy 15, 16GB and 500GB (7200 RPM) Hard drive. Had a VM configured from another environment, created the virtual machine config file on Virtual Box, everything seemed ok. Fired it up, and it was  s   l   o   w, it took close to 10 minutes for it to load, and about 5 more to see Windows was in the process of loading before the BSOD.  Thought, maybe, just maybe it will not happen again … oh was I wrong. Frustration had already hit an all time high with this configuration and the number of issues I’ve had. How I did the troubleshooting … The best thing to do (IMO) is to step back, and gather your tools to debug this situation. Tools:  Virtual Box command line tools, Windows Debug. Virtual Box comes with a pretty good set of tools to examine, migrate and overall tasks to deal with VMs. The firs step:  use VBoxManage to prevent the VM from rebooting after the error to get enough time to really dig into the BSOD issue. Command used:   VBoxManage setextradata VMNAME "VBoxInternal/PDM/HaltOnReset" 1 Once this was done, the error reported was an “Inaccessible boot device” coming from a “Stop – 7B” type of error on the BSOD. The issue I had with this, my VM was configured to use a virtual SATA controller, and thought Windows 2008 R2 would handle this fine … again wrong!  Because the integration tools from the other product where wanting to take effect that was throwing everything off. The fix The fix was almost handed to me, edited the configuration for the VM, removed the SATA controller from it, added the virtual hard drive under an IDE controller, boot up and voilà … it works! I was then able to install the Virtual Box guest tools and such, but have decided to favor “keep on working” over “let’s try SATA again”

  Read the article

• Ubuntu 12.04 startup is slow and dmesg output seems to lose several seconds

  - by cdowen

  I use ubuntu on Dell Inspiron n4050.I have upgraded to ubuntu 12.04 from 10.04. But now I find the system startup is a little slow and plymouth only show purple screen without logo during startup. When I use dmesg, it shows such messages: [ 2.497750] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 2.603028] usb 2-1.6: new high-speed USB device number 3 using ehci_hcd [ 2.715538] Initializing USB Mass Storage driver... [ 2.715594] usbcore: registered new interface driver usb-storage [ 2.715596] USB Mass Storage support registered. [ 21.317843] Adding 2000892k swap on /dev/sda5. Priority:-1 extents:1 across:2000892k [ 21.323724] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 21.391450] udevd[431]: starting version 175 I wonder what it is doing between 2 second and 21 second. Is it related to being so slow? I tried bootchart. It gave me a complex picture. Sorry I can't post it here. http://3.bp.blogspot.com/-7LX8T5uQvlw/UKhdFMVkp4I/AAAAAAAAADg/dtxePkE94mg/s320/lengzhen-ubuntu-precise-20121118-1.png While ubuntu is booting , I also noticed that it appears:/tmp is not ready or present And sometimes follows *Stop saving kernel messages. Is this the reason dmesg lost output?

  Read the article

• My new hard drive won't automount on boot

  - by user518

  I installed a new hard drive right before installing the new Ubuntu 11.10 by reformatting, not upgrading. I was able to mount my drive, and partition it. It's a 1TB, and I was able to transfer all of my music, and videos to it. For some reason, it won't mount on boot, and I can't figure out how to manually mount it afterwards either. Here's my current /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation UUID=e0fbdf09-f9a0-4336-bac3-ba4dc6cfbcc0 / ext4 errors=remount-ro,user_xattr 0 1 # swap was on /dev/sda5 during installation UUID=adf15180-c84c-4309-bc9f-085fd7464f89 none swap sw 0 0 /dev/sdc1 /media/sdc1 ext4 defaults 0 0 The last line is what I added for my hard drive. Here's the output from sudo lshw -C disk: % sudo lshw -C disk ~ *-disk:0 description: ATA Disk product: ST3250310AS vendor: Seagate physical id: 0 bus info: scsi@2:0.0.0 logical name: /dev/sda version: 3.AD serial: 6RYBF2QE size: 232GiB (250GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000da204 *-cdrom description: DVD-RAM writer product: DVD+-RW DH-16A6S vendor: PLDS physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 version: YD11 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc

  Read the article

• Can't install Ubuntu 12.04 64-bit on a dual-drive MacBook Pro 8,2

  - by kizdp

  Good afternoon, this is the first time I participate here as I'm new to Linux. I've been trying to solve the following problem for over a week without any sign of success so I hope there's a much more knowledgeable person here that can give me a solution. I have an early 2011 MacBook Pro (8,2) with Mac OS X running in a SSD. Then, instead of the Optical bay, I have a HDD in where I would like to install Ubuntu to run it natively. I've tried to do the normal installation process, with or without rEFIt, but it seems the problem resides on the communication between the device containing the Ubuntu .iso file and the laptop. It doesn't allow communication with the boot CD or USB drive. It usually says: “Loading bootlogo...” after I click on the “boot from CD, Linux Icon”. After trying several things, I would like to know if I could install Ubuntu on the HDD as an external HDD (using a friend's Window's system) and then simply put it back into my laptop so as to become an Internal HDD again. I guess, I would have to reinstall many drivers and so on, but would this approach work? Thanks in advance and sorry for this huge block of text

  Read the article

• Can't install Ubuntu in Windows 8

  - by user171635

  I’ve been trying to install Ubuntu 13.04 64-bit edition on an ASUS (K53Z) laptop. I have Windows 8 64-bit installed in a non UEFI mode (I think since it starts-up with the Windows logo and I don’t have the UEFI settings). This laptop had installed Windows 7 and when I upgraded it I didn’t knew about the UEFI advantages. I tried several times to install Ubuntu from a USB device and it loads the logo and then I can’t go further in the installation. I thought it was the version of Ubuntu and tried to install Fedora (even if I personally prefer Ubuntu). I had the same problem: Fedora’s logo appears and it gets stuck. I tried also to boot from different USB devices and didn’t work either. My Bios has EFI options to boot but they were not enabled. So I tried to enable them to boot the USB in UEFI mode. A menu shows up with the options of install Ubuntu and try Ubuntu. If I click the Install or try option, I get a black screen and I can’t go further with the install (which I think is normal since I don’t have Windows 8 in EFI mode). My hypothesis is that the Bios isn’t letting Ubuntu write or read from my SSD, because the activity LED in the USB memory is on when it’s loading the installation files. Once the files are ready and the Ubuntu logo is loaded I don’t see a LED activity on neither the SSD or the USB. Thanks If I missed data you can ask me.

  Read the article

• Kubuntu never gets to the login screen

  - by searchfgold6789

  I am not sure if Xorg is using the right device... The system in question is an A4-1400 CPU with built-in Radeon Graphics. I added a PCIe Radeon HD 5750, and changed the BIOS so it would use that card automatically. Now it appears that I can see output from the TV plugged into the HDMI port, and boot into recovery mode, but cannot get to a desktop - X doesn't start. It just freezes at the Kubuntu splash screen. I have no idea how to get X to use the proper graphics card. I pasted the Xorg.log to http://paste.ubuntu.com/6261137/. And the Xorg.conf generated by aticonfig --initial is at http://paste.ubuntu.com/6261161/ Also, see lspci and lshw -c display outputs. I can provide more information, but something does tell me X is not using the right graphics card and I've no idea where to begin how to fix it... I faced a similar issue before with another distribution but found no information anywhere on how to make X use a specific graphics card. Or maybe it's not that simple.

  Read the article

• Win8 x64 Laptop (Samsung) unable to boot after installing Ubuntu

  - by user285872

  I posted here a while back and no one was able to help me so I am going to try to explain my problem better. I have a Samsung series 7 Ultrabook and I connected a USB optical drive with an Ubuntu 14.04 installation disc. I did not set or change any of my partitions, however, as I mainly wanted to just be able to boot from the disc and fool around with Ubuntu. Upon restarting my computer I get a blue-screen message saying: Recovery Your PC needs to be repiared The Boot configuration date file is missing some required information. File: \BCD Error Code: 0xc000000d You'll need to use the recovery tools on your installing media. If you don't have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. However I am never given the option to even try to boot to anything. When I turn my computer on the optical drive spins and then after a moment or two comes to a halt. I turned off safeboot and switched it to CSM (I believe that is what it is called) mode, and that makes it so when I turn my computer on it takes me to a Windows Recovery screen. I am able to change the date I want to recover and view all the applications installed, however upon recovering Windows says "All boot options are tried. Press key to recover with factory image using Recovery or any other keys for next boot loop iteration." It seems to be stuck in a loop. Can someone please help me?! I'm so confused and nothing is working!

  Read the article

• Battery Life in ubuntu 14.04

  - by user287466

  Today i had fresh installation of ubuntu 14.04 previously i had ubuntu 12.04 and had 5 to 6 hours of battery backup even at constant work, but in 14.04 getting 3 hrs only, tried with tlp but no use. lspci: 0:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 02:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01)

  Read the article

• Partitions mixing up

  - by anon

  I am trying to install ubuntu alongside my windows 7. The problem is that ubuntu is not detecting all of my partitions and basically clubs together many of them. The same thing is done by using GParted. However this problem does not arise while I am using Windows - 7. I cant paste the image of GParted since I dont have the required reputation... I think this could be due to stray GPT data but am not sure how to take care of it. Can someone help me figure this out ? The output of fdisk -l is as follows Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x20000000 Device Boot Start End Blocks Id System /dev/sda1 63 2047 992+ 42 SFS /dev/sda2 * 2048 206847 102400 42 SFS /dev/sda3 206848 146802687 73297920 42 SFS /dev/sda4 146802688 625140399 239168856 42 SFS However actually I have 4 partitions along with 25 gb unallocated space that I had thought to use for Ubuntu installation.

  Read the article

• Unreal Torunament (UT99) no sound in 12.04?

  - by Talas

  I've been trying to get sound working in Unreal Torunament for a couple of days now. I'm using the native Unreal Tournament version, not wine or something like that. I have sound in all other games and media applications that I have tried. In older ubuntu versions it worked fine. I'm now using kubuntu 12.04, I have all the alsa-oss and oss-compat packages installed. I have followed most of the advice out there, and it all seems to fall on padsp and aoss. My problem, however, is that even when trying to use padsp or aoss, I can't get any sound at all. (Note UT has two output modes: ALAudio and Generic(OSS), I have tried both). Is there some configuration required to use padsp or aoss correctly? I have ran it like padsp ./ut and aoss ./ut If using the AL backend in UT I get (both aoss and padsp give this): Bound to ALAudio.so open /dev/dsp: Invalid argument Audio initialization failed. If using the OSS backend in UT I get (both aoss and padsp give this): Bound to Audio.so Failed to open audio device. Audio initialization failed. Note that so far, I have gotten absolutely no sound. Thanks for any help!

  Read the article

• How to fix GRUB on dualboot with Windows7 and Ubuntu?

  - by b_oliv

  I am a relatively recent user of Linux. I had several releases of Ubuntu installed on my laptop working in dual-boot and never had any issues. Recently, I installed openSUSE because I thought it would be necessary for an assignment at my university. It turns out it wasn't so I returned to Ubuntu and decided to burn the new .iso to a CD and install it. The problem is that during installation process I almost for sure messed up with the partitions and now, whenever I tried to load Windows 7, it will tells me that a required device is inaccessible. So, I reinstalled Ubuntu again and now all I get is that I am redirected to the GRUB menu without any warnings. I tried creating a Windows Recovery Disk but it gives me Unexpected I/O error. I suspect it is because it was downloaded from the Internet and maybe some files weren't there. I tried everything without success, so I decided to ask here, in the hope I can receive some help and also learn how to help others with it in the future. Here it is my boot info summary: http://paste.ubuntu.com/1344990/ Also, I might add, that on the boot-repair advanced options, the box repair Windows boot files is "locked", so I can't check it. EDIT: Apparentely, the box is locked, because, from what I understood after reading the boot-repair information, everything is fine with my windows boot-files... I still need some guidance though

  Read the article

• external usb hard drive is not being seen anymore

  - by incrediblehulk

  I think my problem is a little different than several other similar titled questions. Everything started while I was using 10.10. External drive was always recognized and mounted, but the timing of this differed. I mean when I booted, the OS sometimes saw the drive immediately, sometimes after a few minutes, sometimes after hours. Although this was annoying, I tolerated this somehow. Then this problem persisted after I upgraded to 11.04 with a clean install. Afterwards, the drive became totally invisible to the OS. It is not even detected as an usb device anymore. However, there is one thing I can do to make it seen. If I boot to another operating system which can detect the drive, and then boot back to ubuntu, everything is perfect. but this is of course very impractical. To summarize, the usb drive is recognized by ubuntu if and only if another OS in the same computer could recognize it first. I should also say I have not had any problems with the same drive in any other OS or a different computer. My drive is philips with a hitachi hdd inside, has its own power source and any other usb powered drives have never caused this kind of a problem. I've tried almost all recommendations in similar topics but none of them seems to be related to this one. What can I possibly do to fix this?

  Read the article

• Ubuntu Wireless not working on Lenovo t400

  - by VmaxBoss

  This problem started after upgrading to 12.04, an my system is 'up2date' Have tried most of the solution-proposals found on the net. lspci -nnk | grep -iA2 net 00:19.0 Ethernet controller [0200]: Intel Corporation 82567LF Gigabit Network Connection [8086:10bf] (rev 03) Subsystem: Lenovo Device [17aa:20ee] Kernel driver in use: e1000e 03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlagn iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off sudo lshw -C network *-network description: Ethernet interface product: 82567LF Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:22:68:1a:c4:75 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.0.2-k2 duplex=full firmware=1.8-3 ip=192.168.2.154 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:29 memory:fc000000-fc01ffff memory:fc024000-fc024fff ioport:1820(size=32) *-network DISABLED description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:6c:2d:24 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:30 memory:f4300000-f4301fff Please help Br/VB

  Read the article

< Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >