Search Results

Search found 10482 results on 420 pages for 'virtual lab'.

Page 349/420 | < Previous Page | 345 346 347 348 349 350 351 352 353 354 355 356  | Next Page >

• How have multiple web servers and IPs on the same physical network

  - by jsigned

  I do web development out of a small office and need to have multiple physical and virtual servers that can be accessed from the internet. I also have a number of devices (computers, laptops, tablets, printers, etc) that need connections as well. I have gotten a subnet of 8 IP's from my ISP and while that is adequate for the web servers its far too small for everything that needs access to the network. My router is an ASUS RT-N16 running DD-WRT. I'm just smart enough about this routing topic to be dangerous, think 2 year old with a magic marker. I would like to keep my internal network NAT'ed on the 192.168.x.x network and route the 68.69.x.x 255.255.255.248 traffic directly to the servers. The physical network consists of the 4 port DD-WRT router and an unmanaged gig switch. I have a fiber connection to the office that works as an Ethernet port. In other words I can plug my laptop directly into it and have access to the internet. There is no login or password and the router is setup to get DHCP from the ISP, and to provide DHCP addresses for the internal network. What I've done so far is google and try different configurations with little success. In the end I decided I didn't even know how to ask the questions needed. My questions are: Is this the best way to configure the network? How do you do it? VLANs? Multiple routers? I've never had to configure a router using anything more than the GUI so if this is command line stuff be gentle.

  Read the article

• Installing SilverStripe on 000webhost.com (Free web host)?

  - by benwad

  Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it brings me to a page with the following errors: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how.

  Read the article

• What is the correct mail set up for multiple domains on one server?

  - by newmarc

  I have a machine (centos 5) with one external ip address. On that machine I have many virtual hosts with a few different top level domain names and sub-domains under those eg. sub1.domain1.com sub2.domain1.com sub3.domain1.com sub1.domain2.com sub2.domain2.com sub1.domain3.com And so on... Alot of these different sites need to send mail as their corresponding domain (or second-level domain at least). I need to set up DKIM, SPF (but that's handled on the DNS) and rDNS lookup so the mail gets received. As I understand it, you can only have one rDNS entry per machine. I could set up a server for each top level domain, but I'm thinking that'll get expensive. What should I do here? Is there a way to have multiple rDNS lookups on one ip address? How do I setup DKIM signing for multiple domain names on the one machine? Are there any services out there that could handle this for me? Thanks for your help...

  Read the article

• Any way to move Office Starter To-Go to a non-flash drive?

  - by Scott Bussinger

  Microsoft's Office Starter edition has an interesting option to create a portable version on a USB flash drive using the "Microsoft Office Starter To-Go Device Manager". This creates a portable version of the Word and Excel starter editions (limited versions of the normal applications that include ads). This would be great for use in Virtual Machines since it requires no registration and has a perpetual license. But I want to copy the files off of the flash drive and just store them in the VHD. The problem is that it appears when you try to run the office.exe executable from anywhere but the USB drive you get the error "Microsoft Office Starter To-Go cannot be launched because it is installed on an unsupported device." Any ideas what it is objecting to and is there a legal workaround for this? A limited but legal and portable version of Word and Excel is a great idea. But tying it specifically to a USB flash drive seems a bit odd. They don't seem to care how many of those flash drives you create so it's not clear what the restrictions are about.

  Read the article

• Page pool memory

  - by legiwei

  I'm currently using Windows XP SP3 32 bit, using C2D E6320 with 2GB RAM. When I am playing Starcraft 2, I encounter an error where it says my system is running low on page pool memory. Starcraft graphic settings suggested a high settings for me. I do not think it has to do with my GC but with my RAM. I then made a search to try to rectify the problem. Apparently, it's something to do with my virtual memory. I then proceed to try to the suggested solution which is to temper the registry and limit the page pool memory to 384MB. However, having done so, I still could not achieved it. I've seen screenshot settings of windows XP with 2GB having 384MB of page pool memory. My default settings puts it at 195MB whereas when I try to increase the pool limit, it can only go to a max of 229MB. I tried increasing my RAM capacity to 3GB but the pool limit still remains. I like to know how to increase my page pool memory. I've tried searching for solution but to no avail other than the one that I've mentioned above (which didn't solve my problem completely).

  Read the article

• ADO 2.8, VMWare and SQL Server - sudden bulk dropped connections

  - by CodeByMoonlight

  We have an overworked server currently running a single SQL Server 2000 instance on physical hardware, and about 40 different apps interact with it on a daily basis. Last year, the RAID controller failed and we had no spare, so IT Support hurriedly migrated it overnight to a copy running on a VMWare Server. While it was on that server everything ran much quicker due to it being a big improvement in spec. However, the biggest app using it had occasional serious errors which never occurred on physical hardware. Specifically, several times a week it would disconnect batches of users - anywhere from just ten to hundreds at once, and all at the same time. It didn't affect any particular users or PCs or offices - all were affected equally. The only common thing was the app, which is a VB6 app using ADO 2.8 to connect. The other apps connecting to that virtualised instance of SQL Server seemingly had no problems, although they were (and are) responsible for only a tiny fraction of the work involving this server. The upshot is that after about two weeks of loving the speed and hating the random mass disconnections (which we were never able to find a cause for), we sadly took the decision to return to physical hardware and the disconnections vanished. Now we've reached the point where the old server just can't handle all that's being asked of it, and we're intending to migrate everything to 2 or more other servers. The snag is that there's a good chance they'll have to be virtual ones again. Given what happened last time, I'm trying to find out what possible reasons there could be for these mass disconnections. We were running VMWare ESX, but the network is Novell-based. Also, the server had a linked server setup to connect to an Informix server using a known-to-be-buggy ODBC driver, and this is used throughout the day. Any ideas on the cause(s)?

  Read the article

• Windows XP seemingly out of resources but plenty of free RAM and swap available

  - by Artem Russakovskii

  This one has been bothering me for years and so far I couldn't find an adequate solution. The problem occurs on pretty much every XP install I've done. After opening a variety of programs or the system running existing programs for a while, Windows seemingly runs out of resources, without telling me. There's ALWAYS free RAM. For example, it just happened to me and I had over a gig of free RAM. There are no viruses, spyware, or other nonsense - it is a Windows resource problem, but the question is which resource is it running out of, how does one pinpoint it, and how does one prevent it? Sometimes, this happens after running specific programs - for example, today it happened when I started Photoshop CS4 and Flash CS4 at the same time. I also noticed that restarting The Bat (email client by Ritlabs) seems to get rid of this problem for a while but again, this happens on machines that don't even have The Bat installed. So what does exactly happen? The symptoms are: pressing alt-tab doesn't bring up the list anymore - it just jumps to the next window instantly, very similar to the way Alt-Esc works, however in this case, it's due to not having enough resources to bring up the alt-tab menu random programs would randomly crash, citing random errors, out of memory errors, system resources, inabilities to do system calls, etc. random programs would start missing random parts - for example, Firefox top menus might disappear, pull up partial selections, or not pull up anymore altogether. IE might lose a few of its toolbars. Some programs might fail to redraw or would just plain go gray where the UI used to be. Windows itself never complains about running out of RAM, virtual memory, or anything at all, yet it's running out of something. The only clue I was able to find and apply the fix today was this Desktop Heap Limitation. I haven't confirmed the fix working as not enough time passed. In the meantime, what are everyone's thoughts?

  Read the article

• Use Mac OS X Server As Development Environment

  - by macinjosh

  I've installed Mac OS X Server 10.6.3 on my laptop to use as my normal OS. I do a lot of web development and thought it would be handy to run OS X Server so I could more easily manage my local development environment (Apache Virtual Hosts, Hostnames for each local site, etc). I'm really enjoying the new setup except for one problem. DNS. My ideal situation would be to add a site (some-site.local) in the Web Service and then go to the DNS Service and add a primary record for the new site. I actually got this working at one point but after a reboot it stopped working! The records look the same as they did before the reboot but the site doesn't come up in Safari. Here is a list of my needs: Need to be able to add new domains at a whim Domains always map to a site on the same box's Web Service Local & External IPs often change It would nice if it worked on any network (i.e. WiFi at the airport or coffee shop) Sites only need to be accessible locally Configuration should stay put even after rebooting I've done some googling and used this as a bit of guide. In the past I've used MAMP and then just a local Apache/PHP/MySQL install with a manually managed hosts file. I'd rather not go back.

  Read the article

• Problem hosting server behing personal router

  - by Venkatesh Hodavdekar

  I recently bought the domain name lucidcontraptions.com and want to host the website from home. I have a D-Link router in which I have set up my personal virtual server correctly. My application server is Apache 2.2. The server works perfectly with the following settings: External IP: 207.172.xx.xx. Public port: 8888 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx:8888/ the server works perfectly and my Apache page shows up without any issues, both from inside the intranet as well as outside. This setting would not work out for me as I am not allowed port numbers in my DNS management. Now when I tweak the settings to the following: External IP: 207.172.xx.xx. Public port: 80 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx/ the server works perfectly and my Apache page shows up without any issues, BUT ONLY FROM INSIDE THE INTRANET. This page does not show up for people outside the intranet.

  Read the article

• apache2: ssl_error_rx_record_too_long when visiting port 80?

  - by John

  Hi, I have an Ubuntu 10 x64 server edition machine. I got a second IP and configured /etc/network/interfaces like so (actual IPs and gateways removed): auto lo iface lo inet loopback #iface eth0 inet dhcp auto eth0 auto eth0:0 iface eth0 inet static address [ my first IP ] netmask 255.255.255.0 gateway [ my first gateway ] iface eth0:0 inet static address [ my second IP ] netmask 255.255.255.0 gateway [ my second gateway ] /etc/apache2/ports.conf: Listen 80 NameVirtualHost [ my first IP ]:80 NameVirtualHost [ my second IP ]:80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 NameVirtualHost [ my first IP - some site is running SSL successfully using it ]:443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> /etc/apache2/sites-enabled/mysite.conf: <VirtualHost [my second IP ]:80> ServerName mysite.com Include /var/www/mysite.com/djangoproject/apache/django.conf </VirtualHost> Then when visiting http[mysite].com:80 or http[mysite].com (:// removed because serverfault doesn't allow me to post hyperlinks), I get: An error occurred during a connection to [mysite].com. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) My guess is that the configuration file is not being picked up, and apache is therefore looking for the default-ssl file, which is not in conf-enabled. If I were to configure that file properly, it seems I would successfully connect to whatever default directory is specified in the default-ssl file. But I want to connect to my website. Any ideas? Thanks in advance!

  Read the article

• Nginx Not Passing URL Parameters

  - by jmccartie

  Messing around with Nginx ... for some reason, it looks like none of my URL parameters are being passed. My homepage loads fine, but a URL like "http://mysite.com/more.php?id=101" throws errors, saying that the ID is an undefined index. I'm assuming this is something basic I'm missing in a conf file. Some info: conf.d/virtual.conf server { listen 80; server_name dev.mysite.com; index index.php; root /var/www/dev.mysite.com_html; location / { root /var/www/dev.mysite.com_html; } location ~ \.php(.*)$ { fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME /var/www/wap/dev.mysite.com_html/$fastcgi_script_n ame; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } } Error log: 2009/06/22 11:44:21 [notice] 16319#0: start worker process 16322 2009/06/22 11:44:28 [error] 16320#0: *1 FastCGI sent in stderr: "PHP Notice: Undefined index: id in /var/www/dev.mysite.com_html/more.php on line 10 Thanks in advance.

  Read the article

• Getting Windows (VMware) to load from OSX's localhost without an Internet Connection

  - by Jonah Goldstein

  I'm using MAMP to host my local sites, and VirtualHostX so that I can access sites during local development via a convenient URL like mysite.dev I'm also running Windows XP via VirtualBox, and it would be great to be able to load up any of my local sites within windows while offline as currently often working without access, on the move, unfortunately. I know that I can append my IP and a nice domain name to the host file in C:/WINDOWS/system32/drivers/etc ... and i can find my IP simply through terminal with "ifconfig" while I'm online. The problem is that when I'm not online, there's no IP. Even if there is an IP (when i have a connection), I still have grab it and update the windows hosts' file all the time, since I'm developing from a laptop and have a new IP at the drop of a dime. I found a tutorial where the author is able to get a permanent IP. He uses VMware Fusion as his VMachine, which is the only difference between his setup and mine. By running the terminal command "ifconfig vmnet1" he gets: a secret IP the virtual machine uses to talk to OSX And that doesn't change - which is awesome. I'm assuming it exists even if he's offline. His tutorial is here, http://bit.ly/U2lq It would be pretty fantabulous if I could replicate this with virtualBox. Anyone have ideas? Thanks:)

  Read the article

• Where is my CPU usage going?

  - by Josh

  My Ubuntu 10.04 Lucid virtual machine is saying it's at 100% CPU usage... but all I'm running is Thunderbird. According to top, CPU usage should be ~25.9%... How do I interpret this conflicting output from top? top - 13:55:26 up 3:35, 4 users, load average: 3.03, 2.59, 2.48 Tasks: 178 total, 1 running, 177 sleeping, 0 stopped, 0 zombie Cpu(s): 16.0%us, 79.7%sy, 0.0%ni, 0.0%id, 0.0%wa, 1.3%hi, 3.0%si, 0.0%st Mem: 509364k total, 479108k used, 30256k free, 3092k buffers Swap: 2096440k total, 58380k used, 2038060k free, 225116k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7708 jnet 20 0 480m 109m 17m S 18.4 22.1 21:59.14 thunderbird-bin 4615 jnet 20 0 5488 1268 1040 S 2.3 0.2 5:00.03 nx-rootless-ses 7124 jnet 20 0 56688 27m 4812 S 2.0 5.5 6:35.09 nxagent 6724 nx 20 0 9628 1400 636 S 1.6 0.3 3:26.59 sshd 30106 root 20 0 2544 1236 908 R 0.7 0.2 0:00.33 top 19 root 20 0 0 0 0 S 0.3 0.0 0:22.45 ata/0 38 root 20 0 0 0 0 S 0.3 0.0 0:05.53 scsi_eh_1 345 root 20 0 0 0 0 S 0.3 0.0 0:04.72 kjournald 1719 root 20 0 3260 1192 944 S 0.3 0.2 0:17.36 vmware-guestd 1 root 20 0 2804 1356 940 S 0.0 0.3 0:01.99 init 2 root 20 0 0 0 0 S 0.0 0.0 0:00.01 kthreadd 3 root RT 0 0 0 0 S 0.0 0.0 0:00.00 migration/0 4 root 20 0 0 0 0 S 0.0 0.0 0:00.15 ksoftirqd/0 5 root RT 0 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 ... Specifically I'm referring to the fact that the CPU usage totals show 0% idle time: Cpu(s): 16.0%us, 79.7%sy, 0.0%ni, 0.0%id, 0.0%wa, 1.3%hi, 3.0%si, 0.0%st Yet when adding up the percentages in the %CPU column I get 25.9%, not 100%!

  Read the article

• Multiple Internet connections, multiple networks and split access in Linux

  - by Swapneel Patnekar

  I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

  Read the article

• Deleted vmware ESXi snapshot file - any way to recover?

  - by Mark Allison

  Hi there, I wanted to make some changes to a file server VM today on ESXi 4. The machine is a Debian Lenny guest with two virtual disks - one is 8GB and the other is 500Gb (data). In order to protect the machine from unwanted changes, I made a snapshot of the machine. I went ahead and made my changes and it didn't work out well. So, I powered off the VM and went into snapshot manager and reverted to snapshot. However I reverted to an older snapshot and not the one I just made by mistake. I then (idiotically) deleted the snapshot I just made in snapshot manager. This has resulted in me losing about one year's worth of data. Is there any way to recover this deleted snapshot file? I'm using vmware esxi 4. When I browse the VMWare repository I can see various vmdk files - is it possible the data I need is still there? What should I look for? Thanks, Mark.

  Read the article

• ntpd on Fedora Core 6 with high negative time reset values

  - by Mark White

  The basic problem is we have a FC6 server instance running on a virtual machine, and the system time seems to have been slowly varying until it is now causing a problem. The server runs 24/7 and has been up for 155 days. It has been changed to show GMT, and reports the time as (example) 00:15:15 GMT whereas the actual time is 00:00:00 GMT. This is an offset of 915 seconds. selinux has been changed to 'setenforce 0' for testing and I am running as root. I stop the ntpd service and change the time in System|Administration|Date & Time. The time still shows the same with 'date' in bash. There are no error logs. I change the date with 'date --set' in bash. The response confirms the changed date. I run 'date' and the incorrect date is shown. There are no error logs. I start the ntpd service and /var/log/messages shows success with 'time reset -915.720139s'. The date remains unchanged. ntpq -p shows three three time servers all have offsets of around -915 seconds. I stop ntpd service and try 'ntpd -gqx' and get the same result as above - success, but a large negative time reset. I've tried varying combinations of the above, and a few more settings in System|Administration|Date & Time - no change. I just need to reset the system time to GMT. No offset. But I can't wait for ntpd to slew the time over the next few weeks. Any advice is welcome, cheers! Surely this shouldn't be this difficult... Mark...

  Read the article

• How can I run Gnome or KDE locally in Cygwin?

  - by John Peter Thompson Garcés

  Apparently it is possible to do this using cygwin ports, as can be seen in screenshots. I followed this how-to to get apt-cygports set up, and I used it to install gnome-session. This how-to supposedly gives the commands needed to run Gnome or KDE, but whenever I try to run Gnome, a blank X-window pops up and then quickly disappears. Here is the terminal output: $ startx /usr/bin/dbus-launch gnome-session xauth: file /home/jpthomps/.serverauth.4168 does not exist Welcome to the XWin X Server Vendor: The Cygwin/X Project Release: 1.10.3.0 OS: Windows 7 Service Pack 1 [Windows NT 6.1 build 7601] (WoW64) Package: version 1.10.3-12 built 2011-08-22 XWin was started with the following command line: /usr/bin/X :0 -auth /home/jpthomps/.serverauth.4168 (II) xorg.conf is not supported (II) See http://x.cygwin.com/docs/faq/cygwin-x-faq.html for more information LoadPreferences: /home/jpthomps/.XWinrc not found LoadPreferences: Loading /etc/X11/system.XWinrc LoadPreferences: Done parsing the configuration file... winDetectSupportedEngines - DirectDraw installed, allowing ShadowDD winDetectSupportedEngines - Windows NT, allowing PrimaryDD winDetectSupportedEngines - DirectDraw4 installed, allowing ShadowDDNL winDetectSupportedEngines - Returning, supported engines 0000001f winSetEngine - Using Shadow DirectDraw NonLocking winScreenInit - Using Windows display depth of 32 bits per pixel winFinishScreenInitFB - Masks: 00ff0000 0000ff00 000000ff Screen 0 added at virtual desktop coordinate (0,0). MIT-SHM extension disabled due to lack of kernel support XFree86-Bigfont extension local-client optimization disabled due to lack of shared memory support in the kernel (II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so (II) GLX: Initialized DRISWRAST GL provider for screen 0 winPointerWarpCursor - Discarding first warp: 637 478 (--) 5 mouse buttons found (--) Setting autorepeat to delay=500, rate=31 (--) Windows keyboard layout: "00000409" (00000409) "US", type 4 (--) Found matching XKB configuration "English (USA)" (--) Model = "pc105" Layout = "us" Variant = "none" Options = "none" Rules = "base" Model = "pc105" Layout = "us" Variant = "none" Options = "none" winBlockHandler - pthread_mutex_unlock() winProcEstablishConnection - winInitClipboard returned. winClipboardProc - DISPLAY=:0.0 winClipboardProc - XOpenDisplay () returned and successfully opened the display. xinit: XFree86_VT property unexpectedly has 0 items instead of 1 xinit: connection to X server lost waiting for X server to shut down winClipboardProc - winClipboardFlushWindowsMessageQueue trapped WM_QUIT message, exiting main loop. winClipboardProc - XDestroyWindow succeeded. winClipboardProc - Clipboard disabled - Exit from server winDeinitMultiWindowWM - Noting shutdown in progress

  Read the article

• Gerrit ssh key setup on windows server

  - by hotpotato

  I am attempting to configure google's 'Gerrit' code review web app on a Windows server 2008 virtual machine on our internal network. We are using Apache Tomcat (6.0.36) to host the web app and have deployed the gerrit.war to tomcats webapp folder, setup the context.xml, web.xml etc for the web app correctly i believe. However when i startup Tomcat using the $CATALINA_HOME/bin/startup.bat i get the following message in the tomcat logs: *Dec 07, 2012 1:03:54 PM org.apache.catalina.core.StandardContext listenerStart SEVERE: Exception sending context initialized event to listener instance of class com.google.gerrit.httpd.WebAppInitializer com.google.inject.CreationException: Guice creation errors:* 1) No SSH keys under C:\Gerrit\config\etc while locating com.google.gerrit.sshd.HostKeyProvider at com.google.gerrit.sshd.SshModule.configure(SshModule.java:90) I have created a is_rsa.pub SSH key and placed it in the specified directory to no avail. I have been googling this for about a week now and can't seem to find any information about the file or format it is expecting... documentation on setting gerrit up on windows seems hard to come by! Can anyone provide useful information about how to correctly configure a host SSH key in this context?

  Read the article

• How can adding a server to a domain cause Remote Desktop to stop working?

  - by Adrian Grigore

  I have two dedicated with Windows 2008 R2 servers which I am using for Web hosting. One Server A is a domain controller, Server B should simply be added to the domain controlled by Server A. So I RDP'd into Server B and changed the system settings so that Server B is part of that domain. I entered my domain admin credentials, was welcomed to the domain and asked to reboot the server. So far everything seemed to work smoothly After rebooting, I could not open an RDP connection to Server B anymore: Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled. I restored an older backup of Server B and switched off the firewall before adding the server to my domain. But the problem reoccurred just the same. What could be the reason for this? The domain is brandnew and I did not change any of the default settings. Could this be some kind of domain-wide default policy that shuts down RDP on any domain clients? Or perhaps it has to do with the fact that Server B is virtual? Thanks for your help, Adrian

  Read the article

• Repository bugzilla package changed to bugzilla3 in Lenny; upgradable?

  - by Pukku

  This question was asked in debianhelp.org almost half a year ago, but never got an answer. I wasn't the one who posted it, however I was today facing exactly the same question. Not sure if copying it to here as such is considered as inappropriate or something, but there's not really anything that I would even like to paraphrase... So let's just go. (I'm sure you will be happy to close it, if this is not the way to go :) Hello all! We are using a Bugzilla server install on a Debian 4/Etch server and are starting to look at the upgrade to Debian 5/Lenny. I was hoping to upgrade the existing Bugzilla server and database from the oldstable (v2.22) to the newer stable in Lenny (v3) when we get to doing a dist-upgrade. However from testing in a virtual machine it seems that the old package was called "Bugzilla" whereas the Lenny package is called "Bugzilla3" and I could not figure a way to directly upgrade between the two. Is it possible to establish some kind of upgrade path quickly after the dist-upgrade to minimise downtime using apt-get or aptitude? Going on past experiences I would not want to do a fresh install with the Bugzilla3 package and attempt to inject the old database into it (previous attempts failed miserably!) :(

  Read the article

• Thin client - cloud machine - to run via iPad, iPhone, most Androids etc

  - by Carl Lindberg

  I'm tired of having a laptop macbook that breaks down or having files that I need to sync via dropbox etc all the time via the machines to different OS installations. It sucks. I want a thin client where I can login on any machine - my iPhone, PC desktop, iPad etc to one running machine. I would like to replace a modernly powerful desktop iMac with a thin client running via my iPad. I will connect the iPad with a keyboard/mouse too so you get the idea. But I want to be able to use some of the Android phones as well (I guess most Android phones today has a good enough performance/resolution etc to run a thin client). Of course it has to be able to have input/output in sound. Printing can be solved by PDF/emailing etc - so no direct communication to the printer ports to USB etc is necessary. Is there such a service today? It should cost somewhere under something like $40/ month. I will run stuff like CPU heavy duty ableton for music production, xCode for making iOS apps, some games etc. And on the thin client also run virtual machines. VM of Ubuntu and Windows.

  Read the article

• Dell PERC 5 - RAID-10 keeps rebuilding drive 2 every day

  - by raid question

  I have a Dell PowerEdge 2950 with this card: RAID bus controller [0104]: Dell PowerEdge Expandable RAID controller 5 [1028:0015] and six disks in a RAID-10. I replaced drive 2, because it didn't show up, and then it started to rebuild itself: root@backup01:~# megaraidsas-status -- Arrays informations -- -- ID | Type | Size | Status a0d0 | RAID 10 | 5587GiB | DEGRADED -- Disks informations -- ID | Model | Status | Warnings a0e8s0 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s1 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5394 a0e8s2 | ATA ST2000DM001-1E61 1863GiB | rebuild | errs: media:0 other:99 a0e8s3 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s4 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s5 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 The rebuild finishes, then the virtual drive becomes optimal, and drive 2 goes online. Then once a day, drive 2 acts like it's been removed, and the rebuild starts all over again. How do I make this once a day rebuild stop? Event Description: Removed: PD 02(e1/s2) Event Description: Removed: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: State change on VD 00/0 from OPTIMAL(3) to DEGRADED(2) Event Description: VD 00/0 is now DEGRADED1 Event Description: State change on PD 02(e1/s2) from ONLINE(18) to FAILED(11) Event Description: State change on PD 02(e1/s2) from FAILED(11) to UNCONFIGURED_BAD(1) Event Description: Background Initialization failed on VD 00/0 Event Description: Inserted: PD 02(e1/s2) Event Description: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: PD 02(e1/s2) is not a certified drive Event Description: State change on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from UNCONFIGURED_GOOD(0) to OFFLINE(10) from UNCONFIGURED_BAD(1) to UNCONFIGURED_GOOD(0) Event Description: Rebuild automatically started on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from OFFLINE(10) to REBUILD(14)

  Read the article

• Where to place Nginx IP blacklist config file?

  - by ProfessionalAmateur

  I have an Nginx web server hosting two sites. I created a blockips.conf file to blacklist IP addresses that are constantly probing the server and included this file in the nginx.conf file. However in my access logs for the sites I still see these IP addresses showing up. Do I need to include the black list in each site's conf instead of the global conf for Nginx? Here is my nginx.conf user nginx; worker_processes 1; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; include /etc/nginx/conf.d/*.conf; # Load virtual host configuration files. include /etc/nginx/sites-enabled/*; # BLOCK SPAMMERS IP ADDRESSES include /etc/nginx/conf.d/blockips.conf; } blockips.conf deny 58.218.199.250; access.log still shows this IP address. 58.218.199.250 - - [27/Sep/2012:06:41:03 -0600] "GET http://59.53.91.9/proxy/judge.php HTTP/1.1" 403 570 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)" "-" What am I doing incorrectly?

  Read the article

• Can't make Dovecot communicate with Postfix using SASL (warning: SASL: Connect to private/auth failed: No such file or directory)

  - by Fred Rocha

  Solved. I will leave this as a reference to other people, as I have seen this error reported often enough on line. I had to change the path smtpd_sasl_path = private/auth in my /etc/postfix/main.cf to relative, instead of absolute. This is because in Debian Postfix runs chrooted (and how does this affect the path structure?! Anyone?) -- I am trying to get Dovecot to communicate with Postfix for SMTP support via SASL. the master plan is to be able to host multiple e-mail accounts on my (Debian Lenny 64 bits) server, using virtual users. Whenever I test my current configuration, by running telnet server-IP smtp I get the following error on mail.log warning: SASL: Connect to /var/spool/postfix/private/auth failed: No such file or directory Now, Dovecot is supposed to create the auth socket file, yet it doesn't. I have given the right privileges to the directory private, and even tried creating a auth file manually. The output of postconf -a is cyrus dovecot Am I correct in assuming from this that the package was compiled with SASL support? My dovecot.conf also holds client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } I have tried every solution out there, and am pretty much desperate after a full day of struggling with the issue. Can anybody help me, pretty please?

  Read the article

• when i try to access website without www. i get access denied.

  - by madphp

  I have an apache web server on a debian machine. Im using virtualmin to administer virtual hosts. I have two sites on this server right now, when i try to access one site without the www in the URL i get an access denied. The other site is fine. The site with the problem is a cakephp app and has the following .htaccess file in the public_html folder. <IfModule mod_rewrite.c> RewriteEngine on RewriteRule ^$ app/webroot/ [L] RewriteRule (.*) app/webroot/$1 [L] </IfModule> Below is the directives for the problem domain. SuexecUserGroup "#1001" "#1001" ServerName mydomain.net ServerAlias www.mydomain.net ServerAlias webmail.mydomain.net ServerAlias admin.mydomain.net DocumentRoot /home/mydomain/public_html ErrorLog /var/log/virtualmin/mydomain.net_error_log CustomLog /var/log/virtualmin/mydomain.net_access_log combined ScriptAlias /cgi-bin/ /home/mydomain/cgi-bin/ ScriptAlias /awstats/ /home/mydomain/cgi-bin/ DirectoryIndex index.html index.htm index.php index.php4 index.php5 <Directory /home/mydomain/public_html> Options -Indexes +IncludesNOEXEC +FollowSymLinks +ExecCGI allow from all AllowOverride All AddHandler fcgid-script .php AddHandler fcgid-script .php5 FCGIWrapper /home/mydomain/fcgi-bin/php5.fcgi .php FCGIWrapper /home/mydomain/fcgi-bin/php5.fcgi .php5 </Directory> <Directory /home/mydomain/cgi-bin> allow from all </Directory> RewriteEngine on RewriteCond %{HTTP_HOST} =webmail.mydomain.net RewriteRule ^(.*) https://mydomain.net:20000/ [R] RewriteCond %{HTTP_HOST} =admin.mydomain.net RewriteRule ^(.*) https://mydomain.net:10000/ [R] RemoveHandler .php RemoveHandler .php5 IPCCommTimeout 31 <Files awstats.pl> AuthName "mydomain.net statistics" AuthType Basic AuthUserFile /home/mydomain/.awstats-htpasswd require valid-user </Files>

  Read the article

< Previous Page | 345 346 347 348 349 350 351 352 353 354 355 356  | Next Page >