Search Results

Search found 11718 results on 469 pages for '2 epm installs and config'.

Page 35/469 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

  • BIND split-view DNS config problem

    - by organicveggie
    We have two DNS servers: one external server controlled by our ISP and one internal server controlled by us. I'd like internal requests for foo.example.com to map to 192.168.100.5 and external requests continue to map to 1.2.3.4, so I'm trying to configure a view in bind. Unfortunately, bind fails when I attempt to reload the configuration. I'm sure I'm missing something simple, but I can't figure out what it is. options { directory "/var/cache/bind"; forwarders { 8.8.8.8; 8.8.4.4; }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; zone "." { type hint; file "/etc/bind/db.root"; }; zone "localhost" { type master; file "/etc/bind/db.local"; }; zone "127.in-addr.arpa" { type master; file "/etc/bind/db.127"; }; zone "0.in-addr.arpa" { type master; file "/etc/bind/db.0"; }; zone "255.in-addr.arpa" { type master; file "/etc/bind/db.255"; }; view "internal" { zone "example.com" { type master; notify no; file "/etc/bind/db.example.com"; }; }; zone "example.corp" { type master; file "/etc/bind/db.example.corp"; }; zone "100.168.192.in-addr.arpa" { type master; notify no; file "/etc/bind/db.192"; }; I have excluded the entries in the view for allow-recursion and recursion in an attempt to simplify the configuration. If I remove the view and just load the example.com zone directly, it works fine. Any advice on what I might be missing?

    Read the article

  • config a router to act as a client and access another wireless router/network, wag120n

    - by mihai
    I currently have a WAG120N( http://www.linksysbycisco.com/EU/en/support/WAG120N) router and I would like to know if it's possible to configure it to connect to a different wireless network(WEP with no password) so I can get internet access on it and then to connect a pc to this router(WAG120N) so I can take advantage of the internet connection. Basically I think that my need is a kind of yagi antenna but as I already got this router I would like to know if I can use instead it of yagi . Thank you in advance for any answer !

    Read the article

  • IBM Server Config questions

    - by Joel Coel
    I have a few questions on a potential server setup. First, the situation: Last year we bought an IBM x3500 server with 2 Xeon E5410's, 9GB RAM, 6 HDDs. The original intent for this server was to replace the old exchange e-mail server. It was brought in, set up, and then shortly after we switched to gmail. Shortly after that my predecessor left for greener pastures, and finally I was hired. So this nice server is now sitting (mostly) idle. This year I have budget again for one server, and of course I want to put this other server to work. I'm thinking about the best use for the two server, and I think I finally have a plan for what I want to do with them. The idea is to use the two newer servers as a pair of VM hosts. I will set up each server with the same 8 VMs, but divide up the load so that only 4 are active per physical host. That means I've normally got 2GB RAM + 2 cores per host. I've done some load testing to pick out what servers to convert to virtual, and chose them so that each host will be capable of handling the entire set of 8 by itself in a pinch with 1 core and 1GB RAM, but would be very taxed to do so. This should take our data center from 13 total servers down to 7. The "servers" I'm replacing are mostly re-purposed desktops, so I'm more than happy to be able to do this. Now it's time to go shopping for the new server. I'd like my two hosts to match as closely as possible, and so I'm looking at IBM again. It also helps that we have some educational matching grant money from IBM that I need to use to help pay for this system (we're a small private college). So finally, (if you're not bored already), we come to my questions: Am I missing anything big or obvious in this plan? I'm a little worried about network performance since the VM hosts will only have 4 nics total where 8 used to be, but I don't think it will be a problem. Is there anything else like this I might be overlooking? Am I making it even too complicated? IBM no longer has a good analog to last year's server. If I want to match the performance (8 cores, 9GB RAM, 1333mhz front side bus, 6 spindles), I have to spend quite a bit more than we paid last year: $2K+, or nearly a 33% cost increase. This only brings a marginal increase in performance. The alternative to stay in budget is to take a hit on the fsb down to 800mhz or cut the number of cores in half, neither of which is attractive. The main cost culprit is the processor. IBM no longer offers the E5410. It's listed as a part, but not available in any of the server configs I've looked at. I'm considering getting the cheapest 800mhz fsb dual core xeon I can configure and then buying the E5410's separately. That's still an extra $350 I wasn't counting on, but that's better than $2K. I want to know what others think of this - will it work or will I end up with the wrong motherboard or some other issue? Am I missing a simple way to configure the server I really want? I don't really intend to do this, but one option to save some money back is to omit the redundant power supply. Since my redundancy plan for these system is to switch over to a completely different host, the extra power isn't fully necessary. That said, it's still very helpful to avoid even short downtimes while I switch over VMs. Has anyone done this?

    Read the article

  • How should I config Apache2.2?

    - by user1607641
    I tried to configure Apache 2.2.17 with PHP5.4 using this manual. But when I restarted my PC and went to http://localhost/phpinfo.php, I received this message: Not Found. The requested URL /phpinfo.php was not found on this server. Here is my httpd.conf - (full version with comments) and a copy with the comments stripped for brevity: ServerRoot "C:/Program Files/Apache2.2" #Listen 12.34.56.78:80 Listen 80 LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule cgi_module modules/mod_cgi.so LoadModule dir_module modules/mod_dir.so LoadModule env_module modules/mod_env.so LoadModule include_module modules/mod_include.so LoadModule isapi_module modules/mod_isapi.so LoadModule log_config_module modules/mod_log_config.so LoadModule mime_module modules/mod_mime.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule php5_module "C:/Languages/PHP/php5apache2_4.dll" # PHP AddHandler application/x-httpd-php .php PHPIniDir "C:/Languages/PHP" <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> User daemon Group daemon </IfModule> </IfModule> ServerAdmin [email protected] #ServerName localhost:80 DocumentRoot "C:/Sites" <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> <Directory "C:/Sites"> Options Indexes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.php index.html </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "logs/error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> # You need to enable mod_logio.c to use %I and %O LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "logs/access.log" common </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "C:/Program Files/Apache2.2/cgi-bin/" </IfModule> <IfModule cgid_module> #Scriptsock logs/cgisock </IfModule> <Directory "C:/Program Files/Apache2.2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types #AddType application/x-gzip .tgz #AddEncoding x-compress .Z #AddEncoding x-gzip .gz .tgz AddType application/x-compress .Z AddType application/x-gzip .gz .tgz #AddHandler cgi-script .cgi #AddHandler type-map var #AddType text/html .shtml #AddOutputFilter INCLUDES .shtml </IfModule> #MIMEMagicFile conf/magic # Some examples: #ErrorDocument 500 "The server made a boo boo." #ErrorDocument 404 /missing.html #ErrorDocument 404 "/cgi-bin/missing_handler.pl" #ErrorDocument 402 http://localhost/subscription_info.html #MaxRanges unlimited #EnableMMAP off #EnableSendfile off # Server-pool management (MPM specific) #Include conf/extra/httpd-mpm.conf # Multi-language error messages #Include conf/extra/httpd-multilang-errordoc.conf # Fancy directory listings #Include conf/extra/httpd-autoindex.conf # Language settings #Include conf/extra/httpd-languages.conf # User home directories #Include conf/extra/httpd-userdir.conf # Real-time info on requests and configuration #Include conf/extra/httpd-info.conf # Virtual hosts Include conf/extra/httpd-vhosts.conf # Local access to the Apache HTTP Server Manual #Include conf/extra/httpd-manual.conf # Distributed authoring and versioning (WebDAV) #Include conf/extra/httpd-dav.conf # Various default settings #Include conf/extra/httpd-default.conf <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> Directory with sites is C:/Sites and PHP is located at C:/Languages/PHP.

    Read the article

  • Where to place Nginx IP blacklist config file?

    - by ProfessionalAmateur
    I have an Nginx web server hosting two sites. I created a blockips.conf file to blacklist IP addresses that are constantly probing the server and included this file in the nginx.conf file. However in my access logs for the sites I still see these IP addresses showing up. Do I need to include the black list in each site's conf instead of the global conf for Nginx? Here is my nginx.conf user nginx; worker_processes 1; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; include /etc/nginx/conf.d/*.conf; # Load virtual host configuration files. include /etc/nginx/sites-enabled/*; # BLOCK SPAMMERS IP ADDRESSES include /etc/nginx/conf.d/blockips.conf; } blockips.conf deny 58.218.199.250; access.log still shows this IP address. 58.218.199.250 - - [27/Sep/2012:06:41:03 -0600] "GET http://59.53.91.9/proxy/judge.php HTTP/1.1" 403 570 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)" "-" What am I doing incorrectly?

    Read the article

  • Apache2 Virtualhost practice config issue

    - by sisko
    I am practicing virtualhost configuration. In my /var/www directory I have created 3 directories called test1, test2 and test3 each of which has a simple index.php script in it. I:E test1/index.php etc. In /etc/apache2/sites-available/test1 I have the following configuration: <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName test1 DocumentRoot /var/www/test1 <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/test1/> Options -Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> All the other sites have a similar virtualHost definition. I have enabled the site(the symlink appears in sites-enabled) and I have restarted apache. However, when I visit localhost/test1, I get a 404 Error. My error log show the following message: [Wed Oct 23 06:22:52 2013] [error] [client 127.0.0.1] File does not exist: /var/www/test1/test1 I don't know why I get the double test1/test1 in the error logs. I'm trying to find the right virtualHost setup which will allow all 3 test websites to be served from their URLs I:E test1/index.php, test2/index.php and test3/index.php. Can anyone help me out, please?

    Read the article

  • Vmware - How do i config a host-only network

    - by nXqd
    The understanding about Host-only: I use VMware 7, Vmnet1 is the host-only adapter for host and it's IP is 192.168.209.1 . I'm really confused about this , does it connect to Vmnet 1 switch and Vmnet has DHCP also, it provieds IP range: Why it has virtual host adapter ( Vmnet 1) has IP which isn't in range while it's just an adapter in virtual network, it connects through switch Vmnet like the guest adapter Waiting for your answers , thanks in advance :)

    Read the article

  • Updating Cisco VPN config to add vpnc support

    - by Igor Kuzmitshov
    I have a Cisco 1841 configured for VPN connections of two types: Peer-to-peer for partners' routers (IPsec) — using different crypto isakmp key and crypto map with set peer, set transform-set, match address for every peer (same map name, different priorities). That crypto map name is added to the WAN interface. Client access (PPTP) — using vpdn-group with accept-dialin protocol pptp. Now, a new partner wants to connect using vpnc client. The latter needs IPSec ID (group name) and IPSec secret in addition to username and password. I guess that IPSec secret is pre-shared key that can be specified in crypto isakmp key on Cisco. But I could not find any VPN tutorials involving groups. Hence, my questions: How to add IPSec ID (group name) and IPSec secret on Cisco router for vpnc connections? Should I add a new crypto map matching all addresses as well? Is it possible to add this configuration without breaking the existing setup? Thank you.

    Read the article

  • django subdomains apache config

    - by bocca
    Trying to setup django to take subdomains and use different settings file based on subdomain dns is setup as wildcards apache mod_vhost_alias sounded like good option, it did not work SetEnv DJANGO_SETTINGS_MODULE site.settings.%1 gets this error ImportError: Could not import settings 'site.settings.%1' can mod_vhost_alias be made to work somehow? can rewrite module be used to pass along subdomain to django settings? is there any other way to pick up different settings files based on subdomain

    Read the article

  • Kernel config file generator

    - by lisak
    Hey guys, could please anybody recommend some kind of kconfig generator that would trim modules and built-in stuff that is not needed according to current hardware ? The best I have found is this : http://lkml.org/lkml/2008/9/16/290 I don't care about compilation time and the amount of modules that are not built-in. I'm concerned about performance. I don't know how much memory and runtime is wasted on huge kernels with almost everything possible. I'm a java developer and I don't know what most of the modules and drivers are for. So there is not much I can disable and be sure that I don't screw it up. Thanks in advance

    Read the article

  • Second DocumentRoot for certain URLS

    - by scrr
    Hello, I have the following setup in my apache-config: <VirtualHost 1.2.3.4:80> ServerName example.com:80 ServerAlias www.example.com DocumentRoot /var/www/page <Location "/blog"> DocumentRoot /var/www/blog </Location> RailsBaseURI / RailsEnv development </VirtualHost> However, Apache tells me, I am not allowed to have a second DocumentRoot. How can I make "www.example.com/blog" point to "/var/www/blog"? I'm sure this is basic, but I just can't find the proper documentation online.

    Read the article

  • How to config mysql-server for heavy load

    - by Rasmus
    Im in the process of setting up a new database server. I have been running a few mysql database servers before and it has been working okay. But i would like to hear the recommended setup for my server. For example, what should i set the max connection, query_cache_size, table_cache and so on. I have arround 4-600 per second: Open tables: 112 Queries per second avg: 430.386. The server i am setting it up on have the following configuration: Linux version 2.6.32-5-amd64 (Debian 2.6.32-41squeeze2) 2x Intel Xeon X3440 @ 2.53GHz 4GB Ram /, /boot, /tmp etc on Software RAID1, 2x 7200RPM SATA Data location on Software RAID0, 2x7200RPM SATA Im am going to place the mysql databases on the RAID0. Am im missing anything? Let me know! Thanks in advance, im looking forward to hearing from you :-) /Rasmus

    Read the article

  • All subdomains routed to same DocumentRoot, apache config

    - by ed209
    You've seen it done on sites like basecamphq.com where you would have username.basecamphq.com I'm wanting to do a similar thing, any subdomain is routed through to the same index.php file. so username1.example.com will request /home/some/path/to/www (in here is index.php) and username2.example.com will request the same file I have it working locally, but my server uses cPanel. What would be your guess at the apache conifguration?

    Read the article

  • How to configure citrix presentation server 4.5 login config

    - by Cory
    Hello, I am a little confused as to something my Citrix Server has been doing. When I login to the web login, (username, password, domain); everything logs in ok and I see all the available application. The problem that I was trying to fix is that when I try to start an application, it asks me to login again to the server that is hosting the citrix server. So, is there anyway to have the initial login credentials pass-through to the server login or skip the server login completely? Side note - I do have pass-through authentication enabled on both my internal and external Citrix site. Thanks for the help! Cory

    Read the article

  • It it possible to have multiple ReWrite rules that all do the same Action, for an IIS7.5 webserver?

    - by Pure.Krome
    I've got rewrite module working great for my IIS7.5 site. Now, I wish to add a number of urls that all goto an HTTP 410-Gone status. Eg. <rule name="Old Site = image1" patternSyntax="ExactMatch" stopProcessing="true"> <match url="image/loading_large.gif"/> <match url="image/aaa.gif"/> <match url="image/bbb.gif"/> <match url="image/ccc.gif"/> <action type="CustomResponse" statusCode="410" statusReason="Gone" statusDescription="The requested resource is no longer available" /> </rule> but that's invalid - the website doesn't start saying there's a rewrite config error. Is there another way I can do this? I don't particularly want define a single URL and ACTION for each url.

    Read the article

  • nginx redirect TLD to TLD with virtual folder (example.com => example.com/test)

    - by Amund
    Im running nginx and in the config file I need to always have the domain example.com redirect to example.com/test. I tried various methods for achieving this but I always got a redirect error. What is the correct way to do this? nginx.conf snippet: server { server_name example.com www.example.com; location / { rewrite ^.+ /test permanent; } } server { listen 80; server_name www.example.com example.com; location / { root /var/www/apps/example/current/public; passenger_enabled on; rails_env production; } } Thanks!

    Read the article

  • lighttpd config and rewriting/disabling attempts to access favicon.ico

    - by Kyle
    I've got lighttpd and apache working together on an app I'm building. lighty is serving out static content. However, each time a static asset is requested, I see a not found: favicon.ico message in the logs. I have added the following url rewrite: url.rewrite-once = ( "^/favicon.ico$" => "/assets/images/favicon.png" ) But to no avail; still getting the message. Any ideas?

    Read the article

  • Samba 'include' a per user config script

    - by cb0
    It is possible to use the include = /somepath/%u.smb.conf in the global section to call a script /somepath/cb0.smb.conf if the user cb0 connects to the samba server. Unfortunately this does not wotk for me because testparm alway gives me Can't find include file /somepath/.smb.conf When I connect to the server I can enter a username and pass but it alway rejects the connection. I'm using Samba Version 3.2.5 How can I achieve to load a custom user script depending on the user that is connecting ?

    Read the article

  • Howto change Axis server-config.wsdd sothat we don't expect a SOAPAction

    - by GKForcare
    The problem I'm facing is that the client of my service will never send me a SOAPAction header. How can I tell Axis to still map to the incomming call to my service implementation anyway. I did bump into tricks like adding a Handler like this: <handler name="ReportMapper" type="java:com.mycompany.project.ReportMapper"/> <transport name="http"> <requestFlow> <handler type="ReportMapper"/> <handler type="URLMapper"/> <handler type="java:org.apache.axis.handlers.http.HTTPAuthHandler"/> </requestFlow> <parameter name="qs:list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs:wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> <parameter name="qs.list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs.method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs:method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs.wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> </transport>

    Read the article

  • Config postGreSQL pg_hba.conf restric role access

    - by Mathias
    Hello postgre experts. I am completely new to the game but need the following: I Create a new role with login. Let's say: User1 I then create a Database 'User1Database' and set User1 as the owner. User1 has no rights to do anything except for access. Now when I connect using User1 it somehow has access to all databases. I then learned I neeed to write something in here. User1 should have global access to User1Database and absolutely no access to anything else. What lines do I need to add to my pg_hba file? Currently it looks like this: # IPv4 local connections: host all all 127.0.0.1/32 md5 # IPv6 local connections: host all all ::1/128 md5 host all all 0.0.0.0/0 md5 Hope someone can write me the exact lines and explain them to me.

    Read the article

  • How can I set up OpenVPN to accept more than 60 connections?

    - by Robin
    Greetings! We're using OpenVPN and today hit an unexpected connection limit of 60 - even though max-clients is set to the source code default 1024. Server log: Tue Dec 21 13:49:41 2010 MULTI: new incoming connection would exceed maximum number of clients (60) We're slowly adding new clients to the VPN and expect to hit 200 some time next year, if we can get it working. We're running the server on a Win2003 R2. OpenVPN 2.0.9 Server config as follows: local 192.168.10.211 port 1195 proto tcp dev tun dev-node OpenVPN_Vision ca vision_ca.crt cert vision_server.crt key vision_server.key # This file should be kept secret dh vision_dh1024.pem server 192.168.211.0 255.255.255.0 ifconfig-pool-persist vision_ipp.txt ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 ;client-to-client keepalive 10 120 comp-lzo ;max-clients 100 # Default in source code is 1024 persist-key persist-tun status openvpn-status-vision.log log vision.log verb 3 I would greatly appreciate any help or input on this one. Thanks! Best regards, Robin

    Read the article

  • What are the things to look out for when adding other domain user to your IIS?

    - by Jack
    I have a Windows Server 2008 R2 called Jack11 that joined a domain called Watson.org. It has IIS 7 installed. From my understanding, we need to add the following into the web.config file <system.web> <identity impersonate="true" /> </system.web> Also, we need to ensure that the server Jack11 can ping to the domain Watson.org. What other setting do we need to setup in order for a user of domain Watson.org (e.g. the user Watson\User1 to access the application in the Server IIS? This is because currently, there is a problem as follows: Exception Details: System.Data.SqlClient.SqlException: Login failed for user 'WATSON\User1'. The error message was displayed when the user User1 wish to access one of the web application in server Jack11 IIS and that web application also do some retrieval of records from the database, which is installed in SQL Server 2008 Enterprise located in the same server Jack11.

    Read the article

  • Howto change Axis server-config.wsdd so that we don't expect a SOAPAction

    - by GKForcare
    The problem I'm facing is that the client of my service will never send me a SOAPAction header. How can I tell Axis to still map to the incomming call to my service implementation anyway. I did bump into tricks like adding a Handler like this: <handler name="ReportMapper" type="java:com.mycompany.project.ReportMapper"/> <transport name="http"> <requestFlow> <handler type="ReportMapper"/> <handler type="URLMapper"/> <handler type="java:org.apache.axis.handlers.http.HTTPAuthHandler"/> </requestFlow> <parameter name="qs:list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs:wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> <parameter name="qs.list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs.method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs:method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs.wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> </transport> but that did not help. The mapper is found during the creation of the WSDL but when calling the service, the invoke of the handler is not used. I do need to note that when I simulate the SOAP-call using @curl@ and I do add the SOAPAction header, the invoke is called. Any help would be most appreciated.

    Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >