Search Results

Search found 952 results on 39 pages for 'bluetooth'.

Page 35/39 | < Previous Page | 31 32 33 34 35 36 37 38 39  | Next Page >

  • Integrated webcam in lenovo t410 not working with 12.04

    - by kristianp
    I have a Lenovo T410 with an inbuilt webcam and I haven't been able to get the webcam working. I tried skype, cheese, both just give me a black window. The microphone works fine with skype, by the way. Can anyone provide any clues please? The webcam is enabled in the bios, but there is no light indicating the webcam is on (not sure if there should be, though). I tried this on Kubuntu 11.10 and have upgraded to 12.04 with the same results. The Fn-F6 keyboard combination doens't seem to do anything either. EDIT: I got the webcam replaced, it looks like it was a hardware problem, because it works fine now. Thanks guys. $ ls /dev/v4l/* /dev/v4l/by-id: usb-Chicony_Electronics_Co.__Ltd._Integrated_Camera-video-index0 /dev/v4l/by-path: pci-0000:00:1a.0-usb-0:1.6:1.0-video-index0 And lsusb: $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 004: ID 0a5c:217f Broadcom Corp. Bluetooth Controller Bus 001 Device 005: ID 17ef:480f Lenovo Integrated Webcam [R5U877] Bus 002 Device 003: ID 05c6:9204 Qualcomm, Inc. Bus 002 Device 004: ID 17ef:1003 Lenovo Integrated Smart Card Reader Here is the output from guvcview, minus lots of lines describing the available capture formats. It says "unable to start with minimum setup. Please reconnect your camera.". guvcview 1.5.3 ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, .... { discrete: width = 1600, height = 1200 } Time interval between frame: 1/15, vid:17ef pid:480f driver:uvcvideo checking format: 1196444237 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! Init video returned -2 trying minimum setup ... video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } .... vid:17ef pid:480f driver:uvcvideo checking format: 1448695129 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! ERROR: Minimum Setup Failed. Exiting... VIDIOC_REQBUFS - Failed to delete buffers: Invalid argument (errno 22) cleaned allocations - 100% Closing portaudio ...OK Terminated.

    Read the article

  • Atheros AR9485 wireless card doesn't work in an ASUS K53E

    - by John
    I just installed Ubuntu 11.10 32-bit version in dual boot mode on an ASUS K53. Every thing seems to work fine except for the wireless. The wireless works on Windows 7. Ubuntu finds the wireless card, but it does not appear to be turned on. The only physical means of turning on the card is the FN-F2 key combo. That works on Windows, but not in Ubuntu. I've looked in the forums for a solution and I'm not quite sure what to do. I've gathered the following information: jdwbmc@Spatha:~$ cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" Linux Spatha 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:50:42 UTC 2011 i686 i686 i386 GNU/Linux jdwbmc@Spatha:~$ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:1186] Kernel driver in use: ath9k -- 04:00.0 Ethernet controller [0200]: Atheros Communications AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) Subsystem: ASUSTeK Computer Inc. Device [1043:1851] Kernel driver in use: atl1c jdwbmc@Spatha:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 058f:a014 Alcor Micro Corp. jdwbmc@Spatha:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff jdwbmc@Spatha:~$ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no jdwbmc@Spatha:~$ lsmod Module Size Used by parport_pc 32114 0 ppdev 12849 0 snd_hda_codec_hdmi 31426 1 bnep 17923 2 rfcomm 38408 0 bluetooth 148839 10 bnep,rfcomm snd_hda_codec_realtek 254125 1 binfmt_misc 17292 1 joydev 17393 0 asus_nb_wmi 12469 0 asus_wmi 19333 1 asus_nb_wmi sparse_keymap 13658 1 asus_wmi uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 24262 2 snd_hda_codec 91754 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80468 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 wmi 18744 1 asus_wmi snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event arc4 12473 2 i915 505108 3 snd_timer 28932 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq ath9k 112711 0 psmouse 73673 0 serio_raw 12990 0 mac80211 272785 1 ath9k drm_kms_helper 32889 1 i915 ath9k_common 13599 1 ath9k drm 192226 4 i915,drm_kms_helper ath9k_hw 293893 2 ath9k,ath9k_common ath 19387 2 ath9k,ath9k_hw cfg80211 172392 3 ath9k,mac80211,ath snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,s nd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd snd_page_alloc 14115 2 snd_hda_intel,snd_pcm mei 36466 0 i2c_algo_bit 13199 1 i915 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 3 libahci 25727 1 ahci atl1c 36638 0 xhci_hcd 72915 0 jdwbmc@Spatha:/var/lib/NetworkManager$ cat NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true jdwbmc@Spatha:~$ lspci -nn | grep 0280 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Any help would be appreciated. Thanks.

    Read the article

  • Why does Ubuntu only detect one USB LAN adapters at a time?

    - by EGO
    I try to connect real switch with my computer for an exam preparation, for this purpose I need more than one LAN cards, and there is only one built in LAN card in my computer. So, to get more LAN cards, I bought 4 USB Ethernet adapters (as I have 4 usb ports in may laptop 2 usb 2.0 ports, 2 usb 3.0 ports). When I plug these adapters in my computer Ubuntu only detects one LAN card from 2.0 usb ports, and one LAN card from 3.0 ports. And sometimes detects only one USB LAN from all the usb ports. Actually the real problem is Ubuntu shows these USB LAN adapters in the "lsusb", but does not list them in "ifconfig". Kontron (Industrial Computer Source / ICS Advent) is my LAN USB ethernet. abc@ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 001 Device 003: ID 138a:0018 Validity Sensors, Inc. Bus 001 Device 004: ID 064e:e258 Suyin Corp. Bus 003 Device 011: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 013: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 003 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 005: ID 0a5c:21b4 Broadcom Corp. BCM2070 Bluetooth 2.1 + EDR -- etho is my built in LAN card, while eth1 is the only USB LAN card that ubuntu has detected. abc@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 2c:27:d7:a5:d2:39 inet6 addr: fe80::2e27:d7ff:fea5:d239/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:21056 errors:0 dropped:1 overruns:0 frame:0 TX packets:5669 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1407289 (1.4 MB) TX bytes:372566 (372.5 KB) Interrupt:49 Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:e0:4c:53:44:58 inet6 addr: fe80::2e0:4cff:fe53:4458/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9230 errors:0 dropped:0 overruns:0 frame:0 TX packets:9230 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:557648 (557.6 KB) TX bytes:557648 (557.6 KB) wlan0 Link encap:Ethernet HWaddr cc:52:af:5e:78:05 inet addr:192.168.1.65 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::ce52:afff:fe5e:7805/64 Scope:LinkU UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17389 errors:0 dropped:0 overruns:0 frame:0 TX packets:12231 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22452248 (22.4 MB) TX bytes:1502750 (1.5 MB) If I unplug the USB LAN card which Ubuntu has detected, then Ubuntu will detect a USB LAN card from the remaining plugged adapters, and process go on untill I plug all the USB LAN adapters. Looking for some urgent help. Thanks

    Read the article

  • Nec USB 3.0 controller drops connection - Ubuntu 12.04.1

    - by Tom
    I have some serious problems with Technaxx pci-e 302p card. It has uPD720200a NEC chip with 4020 firmware. BIOS recognises it. Sometimes it recognises devices and system mounts them and are functional for few minutes, other times they can't be mount and error occours. After fresh install card worked fine, but after kernel and firmware update it behaves as mentioned. Outputs: uname -a Linux asd-GA-MA770-UD3 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lspci -vvv USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fd8fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 07d1:3c0a D-Link System DWA-140 RangeBooster N Adapter(rev.B2) [Ralink RT3072] Bus 005 Device 004: ID 1997:1221 Bus 005 Device 003: ID 15c2:003c SoundGraph Inc. lsmod Module Size Used by nls_iso8859_1 12713 0 nls_cp437 16991 0 vfat 17585 0 fat 61512 1 vfat vesafb 13844 1 saa7134_alsa 18602 1 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep tda827x 18182 1 snd_hda_codec_hdmi 32474 1 ir_lirc_codec 12859 0 lirc_dev 19204 1 ir_lirc_codec tda8290 22616 1 arc4 12529 2 snd_hda_codec_realtek 224173 1 ir_mce_kbd_decoder 12777 0 ir_sony_decoder 12510 0 ir_jvc_decoder 12507 0 tuner 27428 1 ir_rc6_decoder 12507 0 snd_hda_intel 33773 5 rt2800usb 22684 0 rt2800lib 58925 1 rt2800usb crc_ccitt 12667 1 rt2800lib rt2x00usb 20762 1 rt2800usb rt2x00lib 51144 3 rt2800usb,rt2800lib,rt2x00usb mac80211 506816 3 rt2800lib,rt2x00usb,rt2x00lib ir_rc5_decoder 12507 0 rc_avermedia_m135a 12526 0 rc_imon_pad 12505 0 ir_nec_decoder 12507 0 cfg80211 205544 2 rt2x00lib,mac80211 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_ctxfi 111202 2 snd_hwdep 13668 1 snd_hda_codec imon 32839 0 snd_pcm 97188 5 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_ctxfi snd_seq_midi 13324 0 saa7134 181851 1 saa7134_alsa videobuf_dma_sg 19354 2 saa7134_alsa,saa7134 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi joydev 17693 0 rc_core 26412 13 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_avermedia_m135a,rc_imon_pad,ir_nec_decoder,imon,saa7134 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 101 videobuf_core 26390 2 saa7134,videobuf_dma_sg v4l2_common 16454 2 tuner,saa7134 videodev 98259 3 tuner,saa7134,v4l2_common sp5100_tco 13791 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 28 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_ctxfi,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device v4l2_compat_ioctl32 17128 1 videodev tveeprom 21249 1 saa7134 i2c_piix4 13301 0 soundcore 15091 1 snd edac_core 53746 0 serio_raw 13211 0 snd_page_alloc 18529 3 snd_hda_intel,snd_ctxfi,snd_pcm edac_mce_amd 23709 0 wmi 19256 0 mac_hid 13253 0 ppdev 17113 0 parport_pc 32866 1 k10temp 13166 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usb_storage 49198 0 uas 18180 0 usbhid 47199 0 hid 99559 1 usbhid firewire_ohci 41000 0 firewire_core 63558 1 firewire_ohci crc_itu_t 12707 1 firewire_core floppy 70365 0 pata_atiixp 13204 2 r8169 62099 0 dmesg | tail after plugging to usb 3.0 port [ 834.871296] sd 9:0:0:0: rejecting I/O to offline device [ 834.871308] sd 9:0:0:0: rejecting I/O to offline device [ 834.871319] sd 9:0:0:0: rejecting I/O to offline device [ 834.871330] sd 9:0:0:0: rejecting I/O to offline device [ 834.871530] sd 9:0:0:0: [sdd] Unhandled error code [ 834.871536] sd 9:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 834.871545] sd 9:0:0:0: [sdd] CDB: Read(10): 28 00 0e 8e 48 0a 00 00 3e 00 [ 834.871564] end_request: I/O error, dev sdd, sector 244205578 [ 834.875497] sd 8:0:0:1: Device offlined - not ready after error recovery [ 834.885339] usb 9-2: USB disconnect, device number 2 Are there any other outputs need for answering? I'll post them ASAP. I could of course reject updating the system but I think it's halfway solution. Any help appreciated. BTW USB 2.0 and 1.1 ports run well, card itself runs under win7 as charm. Tom

    Read the article

  • Unable to make properly work the Ralink rt3090 wifi card on my Lenovo B575 with Kubuntu 12.04 64bit

    - by Sebastien
    I look and tried many solution from many thread but I still unable to make this wifi card work properly (very slow, unable to connect to some wifi spot, etc.). I tried to compile the driver from the ralink website but it doesn't work. Tried to blacklist many mod, withou any result. So here are some command results, hope their help you help me: lspci sebastien@sebastien-portable:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Wrestler [Radeon HD 6310] 00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Wrestler HDMI Audio [Radeon HD 6250/6310] 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42) 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:15.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) 00:15.2 PCI bridge: Advanced Micro Devices [AMD] nee ATI SB900 PCI to PCI bridge (PCIE port 2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe lsmod sebastien@sebastien-portable:~$ lsmod Module Size Used by rt2800pci 18715 0 arc4 12529 2 rt2800lib 58925 1 rt2800pci crc_ccitt 12667 1 rt2800lib rt2x00pci 14577 1 rt2800pci rt2x00lib 55301 3 rt2800pci,rt2800lib,rt2x00pci mac80211 506816 3 rt2800lib,rt2x00pci,rt2x00lib cfg80211 205544 2 rt2x00lib,mac80211 eeprom_93cx6 12725 1 rt2800pci rt2860sta 864748 0 snd_hda_codec_conexant 62128 1 snd_hda_codec_hdmi 32474 1 uvcvideo 72627 0 rts5139 351143 0 snd_hda_intel 33773 4 videodev 98259 1 uvcvideo snd_hda_codec 127706 3 snd_hda_codec_conexant,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec psmouse 87692 0 v4l2_compat_ioctl32 17128 1 videodev serio_raw 13211 0 k10temp 13166 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec sp5100_tco 13791 0 i2c_piix4 13301 0 snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi ideapad_laptop 18234 0 sparse_keymap 13890 1 ideapad_laptop rfcomm 47604 0 joydev 17693 0 snd_seq_midi_event 14899 1 snd_seq_midi bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 18 snd_hda_codec_conexant,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd mac_hid 13253 0 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid r8169 62099 0 radeon 804372 4 video 19596 0 wmi 19256 0 ttm 76949 1 radeon drm_kms_helper 46978 1 radeon drm 242038 6 radeon,ttm,drm_kms_helper i2c_algo_bit 13423 1 radeon iwconfig sebastien@sebastien-portable:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"4CE6763F0E0A" Mode:Managed Frequency:2.452 GHz Access Point: 4C:E6:76:3F:0E:0A Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:100 Missed beacon:0 eth0 no wireless extensions.

    Read the article

  • Microsoft Build 2012 Day 1 Keynote Summary

    - by Tim Murphy
    So I have finally dried the tears after watching the Keynote for Build 2012.  This wasn’t because it was an emotional presentation, but because for the second year I missed the goodies.  Each on site attendee got a Surface RT, a Lumia 920 and a voucher for 100GB of SkyDrive storage. The event was opened with the announcement that in the three days since the launch of Windows 8 over 4 million upgrades have been sold.  I don’t care who you are that is an impressive stat.  Ballmer then spent a fair amount of time remaking the case for the Windows and Windows Phone platforms similar to what we have heard over the last to launch events. There were some cool, but non-essential demos.  The one that was the most fun was the Perceptive Pixel 82” slate device.  At first glance I wondered why I would ever want such a device, but then Ballmer explained it’s possible use for schools and boardrooms.  The actually made sense. Then things got strange.  Steve started explaining features that developers could leverage.  Usually this type of information is left to the product leads.  He focused on the integration with the Charms features such as Search and Share. Steve “Guggs” Guggenheim showed off an app that would appeal to my kids from Disney called “Agent P” which is base on Phineas and Ferb.  Then he got to the meat of the presentation.  We found out that you could add a tile that can be used to sell ad space.  In the same vein we also found out that you could use Microsoft’s, Paypal’s or any commerce engine of your own creation or choosing. For those who are interested in sports and especially developing sports apps you would have found the small presentation from Michael Bayle of ESPN.  He introduced the ESPN app which has tons of features.  For the developers in the crowd he also mentioned that ESPN has an API available at developer.espn.com. During the launch events we were told apps were coming.  In this presentation we were actually shown a scrolling list of logos and told about a couple of them.  Ballmer mentioned specifically Twitter, SAP and DropBox.  These are impressive names that were just a couple of the list impressive names. Steve Ballmer addressed the question of why you should develop for the Windows 8 platform.  He feels that Microsoft has the best commercial terms for developers, a better way to build apps than other platforms and a variety of form factors.  His key point though was the available volume of customers given the current Windows install base and assuming even a flat growth of the platform.  This he backed with a promise that Microsoft is going to do better at marketing and you won’t be able to avoid the ads that they are bringing out. The last section of the key note was present by Kevin Gallo from the Windows Phone team.  This was the real reason I tuned into the webcast.  He impressed upon those watching that the strength of developing for the Microsoft platform is the common programming model that now exist.  While there are difference between form factor implementations you can leverage code across them. He claimed that 90% of developer requests for Windows Phone 8 had been implemented.  These include: More controls with better performance Better live tiles including lock screen integration Speech support in custom apps Easier submission to the market place App camera integration VOIP and chat support Bluetooth and NFC support Native C++ development Direct 3D development   The quote from Kevin that stood out for me was that “Take your Dramamine and buckle your seatbelt type of games are coming to Windows Phone 8”.  He back this up by displaying a list of game development frameworks and then having Unity come out and do a demo. Ok, almost done … The last two things of note for me were the announcement that the SDK is immediately available at dev.windowsphone.com and that they were reducing the cost of an individual developer account to $8 for the next 8 days. Let the development commence. del.icio.us Tags: Build 2012,Windows 8,Windows Phone 8,Windows Phone

    Read the article

  • Incomplete upgrade 12.04 to 12.10

    - by David
    Everything was running smoothly. Everything had been downloaded from Internet, packages had been installed and a prompt asked for some obsolete programs/files to be removed or kept. After that the computer crashed and and to manually force a shutdown. I turned it on again and surprise I was on 12.10! Still the upgrade was not finished! How can I properly finish that upgrade? Here's the output I got in the command line after following posted instructions: i astrill - Astrill VPN client software i dayjournal - Simple, minimal, digital journal. i gambas2-gb-form - A gambas native form component i gambas2-gb-gtk - The Gambas gtk component i gambas2-gb-gtk-ext - The Gambas extended gtk GUI component i gambas2-gb-gui - The graphical toolkit selector component i gambas2-gb-qt - The Gambas Qt GUI component i gambas2-gb-settings - Gambas utilities class i A gambas2-runtime - The Gambas runtime i google-chrome-stable - The web browser from Google i google-talkplugin - Google Talk Plugin i indicator-keylock - Indicator for Lock Keys i indicator-ubuntuone - Indicator for Ubuntu One synchronization s i A language-pack-kde-zh-hans - KDE translation updates for language Simpl i language-pack-kde-zh-hans-base - KDE translations for language Simplified C i libapt-inst1.4 - deb package format runtime library idA libattica0.3 - a Qt library that implements the Open Coll idA libbabl-0.0-0 - Dynamic, any to any, pixel format conversi idA libboost-filesystem1.46.1 - filesystem operations (portable paths, ite idA libboost-program-options1.46.1 - program options library for C++ idA libboost-python1.46.1 - Boost.Python Library idA libboost-regex1.46.1 - regular expression library for C++ i libboost-serialization1.46.1 - serialization library for C++ idA libboost-signals1.46.1 - managed signals and slots library for C++ idA libboost-system1.46.1 - Operating system (e.g. diagnostics support idA libboost-thread1.46.1 - portable C++ multi-threading i libcamel-1.2-29 - Evolution MIME message handling library i libcmis-0.2-0 - CMIS protocol client library i libcupsdriver1 - Common UNIX Printing System(tm) - Driver l i libdconf0 - simple configuration storage system - runt i libdvdcss2 - Simple foundation for reading DVDs - runti i libebackend-1.2-1 - Utility library for evolution data servers i libecal-1.2-10 - Client library for evolution calendars i libedata-cal-1.2-13 - Backend library for evolution calendars i libedataserver-1.2-15 - Utility library for evolution data servers i libexiv2-11 - EXIF/IPTC metadata manipulation library i libgdu-gtk0 - GTK+ standard dialog library for libgdu i libgdu0 - GObject based Disk Utility Library idA libgegl-0.0-0 - Generic Graphics Library idA libglew1.5 - The OpenGL Extension Wrangler - runtime en i libglew1.6 - OpenGL Extension Wrangler - runtime enviro i libglewmx1.6 - OpenGL Extension Wrangler - runtime enviro i libgnome-bluetooth8 - GNOME Bluetooth tools - support library i libgnomekbd7 - GNOME library to manage keyboard configura idA libgsoap1 - Runtime libraries for gSOAP i libgweather-3-0 - GWeather shared library i libimobiledevice2 - Library for communicating with the iPhone i libkdcraw20 - RAW picture decoding library i libkexiv2-10 - Qt like interface for the libexiv2 library i libkipi8 - library for apps that want to use kipi-plu i libkpathsea5 - TeX Live: path search library for TeX (run i libmagickcore4 - low-level image manipulation library i libmagickwand4 - image manipulation library i libmarblewidget13 - Marble globe widget library idA libmusicbrainz4-3 - Library to access the MusicBrainz.org data i libnepomukdatamanagement4 - Basic Nepomuk data manipulation interface i libnux-2.0-0 - Visual rendering toolkit for real-time app i libnux-2.0-common - Visual rendering toolkit for real-time app i libpoppler19 - PDF rendering library i libqt3-mt - Qt GUI Library (Threaded runtime version), i librhythmbox-core5 - support library for the rhythmbox music pl i libusbmuxd1 - USB multiplexor daemon for iPhone and iPod i libutouch-evemu1 - KernelInput Event Device Emulation Library i libutouch-frame1 - Touch Frame Library i libutouch-geis1 - Gesture engine interface support i libutouch-grail1 - Gesture Recognition And Instantiation Libr idA libx264-120 - x264 video coding library i libyajl1 - Yet Another JSON Library i linux-headers-3.2.0-29 - Header files related to Linux kernel versi i linux-headers-3.2.0-29-generic - Linux kernel headers for version 3.2.0 on i linux-image-3.2.0-29-generic - Linux kernel image for version 3.2.0 on 64 i mplayerthumbs - video thumbnail generator using mplayer i myunity - Unity configurator i A openoffice.org-calc - office productivity suite -- spreadsheet i A openoffice.org-writer - office productivity suite -- word processo i python-brlapi - Python bindings for BrlAPI i python-louis - Python bindings for liblouis i rts-bpp-dkms - rts-bpp driver in DKMS format. i system76-driver - Universal driver for System76 computers. i systemconfigurator - Unified Configuration API for Linux Instal i systemimager-client - Utilities for creating an image and upgrad i systemimager-common - Utilities and libraries common to both the i systemimager-initrd-template-am - SystemImager initrd template for amd64 cli i touchpad-indicator - An indicator for the touchpad i ubuntu-tweak - Ubuntu Tweak i A unity-lens-utilities - Unity Utilities lens i A unity-scope-calculator - Calculator engine i unity-scope-cities - Cities engine i unity-scope-rottentomatoes - Unity Scope Rottentomatoes

    Read the article

  • How can I make sound work without starting X?

    - by Magnus Hoff
    I have a headless machine connected to my sound system, and I am using it to run a music playing daemon that I control over the network. (Among other things) However, I can't seem to be able to have sound come out of my speakers without running X. I am running pulse audio in a system wide instance and my daemon is not running within X. Nevertheless, when my daemon is playing music without me hearing it, I can fix it by running startx in an unrelated session. After X starts, I can hear the sound. The sound disappears again if I kill the X server. Interestingly/annoyingly, the sound also stops after X has been running for a few minutes. This could possibly be because of a screen saver of some sort, but I haven't been able to verify or falsify this theory. So my current workaround is to ssh into the box whenever I want music and startx, and restart it every fifteen minutes or so. I'd like to do better. I have been able to verify the following: Adjustments in alsamixer have no effect on this problem. The relevant output channel is never muted In alsamixer, I can see no difference between when the sound is working and when it isn't Nothing is muted in pactl list There is no difference in the output from pactl list between before starting X and after it's started. (Except the identifier of the pactl instance connected to pulse, which is different each time you run pactl) The user running the music daemon is a member of the groups audio, pulse and pulse-access The music daemon program does not report any error messages and acts as if it is playing the music like it should Some form of dbus daemon is running. ps aux|grep dbus reports dbus-daemon --system --fork --activation=upstart before and after I have started X Some details about my hardware: Motherboard: http://www.asus.com/Motherboards/AT5IONTI_DELUXE/ Sound chip: Nvidia GPU 0b HDMI/DP (from alsamixer) Using HDMI for output (Machine also has an Intel Realtek ALC887 that I am not using) Output of lsmod: Module Size Used by deflate 12617 0 zlib_deflate 27139 1 deflate ctr 13201 0 twofish_generic 16635 0 twofish_x86_64_3way 25287 0 twofish_x86_64 12907 1 twofish_x86_64_3way twofish_common 20919 3 twofish_generic,twofish_x86_64_3way,twofish_x86_64 camellia 29348 0 serpent 29125 0 blowfish_generic 12530 0 blowfish_x86_64 21466 0 blowfish_common 16739 2 blowfish_generic,blowfish_x86_64 cast5 25112 0 des_generic 21415 0 xcbc 12815 0 rmd160 16744 0 bnep 18281 2 rfcomm 47604 12 sha512_generic 12796 0 crypto_null 12918 0 parport_pc 32866 0 af_key 36389 0 ppdev 17113 0 binfmt_misc 17540 1 nfsd 281980 2 ext2 73795 1 nfs 436929 1 lockd 90326 2 nfsd,nfs fscache 61529 1 nfs auth_rpcgss 53380 2 nfsd,nfs nfs_acl 12883 2 nfsd,nfs sunrpc 255224 16 nfsd,nfs,lockd,auth_rpcgss,nfs_acl btusb 18332 2 vesafb 13844 2 pl2303 17957 1 ath3k 12961 0 bluetooth 180153 24 bnep,rfcomm,btusb,ath3k snd_hda_codec_hdmi 32474 4 nvidia 11308613 0 ftdi_sio 40679 1 usbserial 47113 6 pl2303,ftdi_sio psmouse 97485 0 snd_hda_codec_realtek 224173 1 snd_hda_intel 33719 5 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel serio_raw 13211 0 snd_seq_midi 13324 0 snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 79041 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device asus_atk0110 18078 0 mac_hid 13253 0 jc42 13948 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm coretemp 13554 0 i2c_i801 17570 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62154 0 Any ideas? What does X do that's so important?

    Read the article

  • Schizophrenic Ubuntu 12.10-12.04: Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to getit to work?

    - by zewone
    I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686 ![Schizophrenic Ubuntu](http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) Any help much appreciated... Thanks, Philippe

    Read the article

  • History of Mobile Technology

    - by David Dorf
    Over the last ten years, mobile phones have gone through several incremental technology leaps that have added capabilities that impact the retail industry.  I've listed the six major ones below, along with their long-lasting impact. 1. Location In the US, the FCC required mobile phones to implement E911 (emergency calls) by 2006, requiring the caller to be located to within 300 meters.  Back in 2000, GPS was opened up for civilian use, and by 2004 Qualcomm had figured out how to use GPS in mobile phones.  So mobile operators moved from cell tower triangulation to GPS, principally for E911.  But then lots of other uses became apparent, especially navigation.  The earliest mobile apps from retailers made it easy to find nearby stores, and companies are looking at ways to use WiFi triangulation inside stores. 2. Computer Vision In 1997 Philippe Kahn shared a photo of his newborn using a mobile phone thus launching the popularity of instant visual communications.  Over the years the quality of the cameras got better, reaching the point where barcodes could be read around 2008.  That's when Occipital came on the scene with their Red Laser application, which was eventually acquired by eBay.  This opened up the ability for consumers to easily price compare inside stores.  Other interesting apps included Tesco's Wine Finder and Amazon's Price Checker, both allowing products to be identified by picture. 3. Augmented Reality Once the mobile phone had GPS, a video camera, and compass functionality it was suddenly possible to overlay digital information on the screen in real-time.  Yelp, which was using GPS to find nearby merchants, created a backdoor called Monocle on the iPhone that showed nearby merchants overlayed on the video camera view.  Today AR apps are mostly used by retailers for marketing, like Moosejaw's app that undresses models in their catalog. 4. Geo-Fencing So if we're able to track the location of a mobile phone, why not use that context to offer timely information?  My first experience with geo-fencing came courtesy of North Face, the outdoor enthusiast store. When a mobile phone enters a predetermined area, like near a store, a text message is sent to phone with an offer or useful information.  Of course retailers can geo-fence their competitors as well and find out which customers are aren't so loyal. 5. Digital Wallet Mobile payments leverage different technologies such as NFC, QRCodes, bluetooth, and SMS to facilitate communication between the consumers's phone and the retailer's point-of-sale. The key here is the potential to consolidate loyalty cards, coupons, and bank cards into the mobile phone and enable faster checkout.  Nobody does this better than Starbucks today, but McDonald's and Duncan Donuts aren't far behind.  Google, Isis, Paypal, Square, and MCX are all vying for leadership in this area.  If NFC does finally take off, it will be leveraged by retailers in more places than just the POS. 6. Voice Response Mobile Phones have had the ability to interpret simple voice commands for a while, but Google and Amazon were the first to use voice to allow searches for products.  Allowing searches by text, barcode, and voice makes it easy to comparison shop in the aisles.  Walmart even uses voice to build shopping lists, and if the Siri API is even opened we could see lots more innovation in this area.

    Read the article

  • Wireless doesn't work on a Broadcom BCM4312

    - by Boderick
    As stated, I've just upgraded to 12.04 and my Dell Inspiron 1545 isn't recognising its wireless card and I was wondering if anybody could help? Edit: Okay, so I found the wireless card by using lspci -vvv and it returned this: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- Kernel modules: ssb lsmod Module Size Used by dm_crypt 22528 0 joydev 17393 0 dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi dell_laptop 13671 0 dcdbas 14098 1 dell_laptop psmouse 72919 0 uvcvideo 67203 0 serio_raw 13027 0 videodev 86588 1 uvcvideo snd_hda_codec_idt 60251 1 mac_hid 13077 0 snd_hda_intel 32765 5 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec parport_pc 32114 0 rfcomm 38139 0 bnep 17830 2 ppdev 12849 0 snd_pcm 80845 3 snd_hda_intel,snd_hda_codec bluetooth 158438 10 rfcomm,bnep snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq binfmt_misc 17292 1 snd 62064 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp sky2 53628 0 ums_realtek 17920 0 uas 17699 0 i915 414603 3 wmi 18744 1 dell_wmi drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 usb_storage 39646 1 ums_realtek ifconfig -a eth0 Link encap:Ethernet HWaddr 00:23:ae:24:71:45 inet addr:192.168.1.158 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:aeff:fe24:7145/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14340 errors:0 dropped:0 overruns:0 frame:0 TX packets:10191 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15403754 (15.4 MB) TX bytes:1262570 (1.2 MB) Interrupt:18 ham0 Link encap:Ethernet HWaddr 7a:79:05:2d:b0:f7 inet addr:5.45.176.247 Bcast:5.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:5ff:fe2d:b0f7/64 Scope:Link inet6 addr: 2620:9b::52d:b0f7/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:27480 (27.4 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:433 errors:0 dropped:0 overruns:0 frame:0 TX packets:433 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:60051 (60.0 KB) TX bytes:60051 (60.0 KB) iwconfig lo no wireless extensions. ham0 no wireless extensions. eth0 no wireless extensions. the results for sudo lshw -class network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0c:00.0 logical name: eth1 version: 01 serial: 00:22:5f:77:1f:e6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f69fc000-f69fffff *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 13 serial: 00:23:ae:24:71:45 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.158 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:f68fc000-f68fffff ioport:de00(size=256) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:05:2d:b0:f7 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.45.176.247 link=yes multicast=yes port=twisted pair speed=10Mbit/s and the results of rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

    Read the article

  • Wireless cycling between connected and disconnected

    - by Tony Kilgore
    My friend has a Acer Aspire 5733Z-4851 it keeps disconnecting and connecting to his wifi but his hard wire will run just fine. Any suggestions? All the codes: lspci: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) lsmod: Module Size Used by snd_seq_dummy 12798 0 rfcomm 46619 0 bnep 18140 2 bluetooth 209199 10 rfcomm,bnep parport_pc 32688 0 ppdev 17073 0 lp 17759 0 parport 46345 3 parport_pc,ppdev,lp binfmt_misc 17500 1 ums_realtek 17949 0 snd_hda_codec_realtek 77876 1 uas 17844 0 coretemp 13400 0 snd_hda_intel 33491 4 snd_hda_codec 134212 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 96580 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30512 1 snd_seq_midi uvcvideo 76749 0 videobuf2_core 32851 1 uvcvideo videodev 120309 2 uvcvideo,videobuf2_core videobuf2_vmalloc 12860 1 uvcvideo videobuf2_memops 13368 1 videobuf2_vmalloc snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61521 3 snd_seq_dummy,snd_seq_midi,snd_seq_midi_event snd_timer 29425 2 snd_pcm,snd_seq arc4 12529 2 snd_seq_device 14497 4 snd_seq_dummy,snd_seq_midi,snd_rawmidi,snd_seq psmouse 95552 0 ath9k 131308 0 tg3 148780 0 snd 78734 17 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device microcode 22803 0 mac80211 539908 1 ath9k ath9k_common 14055 1 ath9k ath9k_hw 395218 2 ath9k,ath9k_common ath 23827 3 ath9k,ath9k_common,ath9k_hw i915 520629 3 soundcore 15047 1 snd serio_raw 13215 0 cfg80211 206566 3 ath9k,mac80211,ath snd_page_alloc 18484 2 snd_hda_intel,snd_pcm intel_ips 18049 0 lpc_ich 17061 0 drm_kms_helper 46784 1 i915 drm 275528 4 i915,drm_kms_helper mei 40690 0 i2c_algo_bit 13413 1 i915 joydev 17457 0 acer_wmi 32453 0 sparse_keymap 13890 1 acer_wmi mxm_wmi 12979 0 mac_hid 13205 0 wmi 19070 2 acer_wmi,mxm_wmi video 19335 2 i915,acer_wmi usb_storage 48838 1 ums_realtek sudo lshw -C network: *-network description: Ethernet interface product: NetLink BCM57780 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: b8:70:f4:9a:35:b6 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=half firmware=sb latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:44 memory:d3400000-d340ffff[/QUOTE][QUOTE]*-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 68:a3:c4:eb:60:7d width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-19-generic firmware=N/A ip=192.168.0.168 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d2400000-d240ffff)

    Read the article

  • Upgraded to 12.04 now wifi doesn't work

    - by Benito Kestelman
    My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

    Read the article

  • How to support 3-byte UTF-8 Characters in ANT

    - by efelton
    I am trying to support UTF-8 characters in my ANT script. As long as the character string are made up of 2-byte UTF-8 characters, such as: Lògìñ Ùsèr ÌÐ Then things work fine. When I use Unicode Han Character: ? Which, according to this site: http://www.fileformat.info/info/unicode/char/6211/index.htm Has a UTF-8 encoding of 0xE6 0x88 0x91 I can see in UltraEdit, my input properties file has the values "E6 88 91" all in a row, so I'm fairly confident that my input is correct. And When I open the same file in Notepad++ I can see all the characters correctly. Here is my Build Script: <?xml version="1.0" encoding="UTF-8" ?> <project name="utf8test" default="all" basedir="."> <target name="all"> <loadproperties encoding="UTF-8" srcfile="./apps.properties.all.txt" /> <echo>No encoding ${common.app.name}</echo> <echo encoding="UTF-8">UTF-8 ${common.app.name}</echo> <echo encoding="UnicodeLittle">UnicodeLittle ${common.app.name}</echo> <echo encoding="UnicodeLittleUnmarked">UnicodeLittleUnmarked ${common.app.name}</echo> <echo>${common.app.ServerName}</echo> <echo>${bb.vendor}</echo> <echo>No encoding ${common.app.UserIdText}</echo> <echo encoding="UTF-8">UTF-8 ${common.app.UserIdText}</echo> <echo encoding="UnicodeLittle">UnicodeLittle ${common.app.UserIdText}</echo> <echo encoding="UnicodeLittleUnmarked">UnicodeLittleUnmarked ${common.app.UserIdText}</echo> <echoproperties /> </target> </project> And here is my properties file: common.app=VrvPsLTst common.app.name=?? common.app.description=Pseudo Loc Test App for Build Script testing common.app.ServerName=http://Vèrìvò.com bb.vendor=Vèrìvò common.app.PasswordText=Pàsswòrð bb.override.list=MP_COPYRIGHTTEXT, "Çòpÿrìght 2012 Vèrívó Bùîlð TéàM" common.app.LoginButtonText=Lògìñ common.app.UserIdText=Ùsèr ÌÐ bb.SMSSuccess=Mèssàgéß Sùççêssfúllÿ Sëñt common.app.LoginScreenMessage=WèlçòMé Mêssàgë common.app.LoginProgressMessage=Àùthèñtìçàtíòñ îñ prógréss... ios.RegistrationText=Règìstràtíòñ Téxt ios.RegistrationURL=http://www.josscrowcroft.com/2011/code/utf-8-multibyte-characters-in-url-parameters-%E2%9C%93/ Here is what the output looks like: Buildfile: C:\Temp\utf8\build.xml all: [echo] No encoding ?? [echo] UTF-8 ?? [echo] ÿþU n i c o d e L i t t l e ? ? [echo] U n i c o d e L i t t l e U n m a r k e d ? ? [echo] http://Vèrìvò.com [echo] Vèrìvò [echo] No encoding Ùsèr ÌÐ [echo] UTF-8 Ùsèr ÃŒÃ? [echo] ÿþU n i c o d e L i t t l e Ù s è r Ì Ð [echo] U n i c o d e L i t t l e U n m a r k e d Ù s è r Ì Ð [echoproperties] #Ant properties [echoproperties] #Mon Jun 18 15:25:13 EDT 2012 [echoproperties] ant.core.lib=C\:\\ant\\lib\\ant.jar [echoproperties] ant.file=C\:\\Temp\\utf8\\build.xml [echoproperties] ant.file.type=file [echoproperties] ant.file.type.utf8test=file [echoproperties] ant.file.utf8test=C\:\\Temp\\utf8\\build.xml [echoproperties] ant.home=c\:\\ant\\bin\\.. [echoproperties] ant.java.version=1.6 [echoproperties] ant.library.dir=C\:\\ant\\lib [echoproperties] ant.project.default-target=all [echoproperties] ant.project.invoked-targets=all [echoproperties] ant.project.name=utf8test [echoproperties] ant.version=Apache Ant version 1.8.1 compiled on April 30 2010 [echoproperties] awt.toolkit=sun.awt.windows.WToolkit [echoproperties] basedir=C\:\\Temp\\utf8 [echoproperties] bb.SMSSuccess=M\u00E8ss\u00E0g\u00E9\u00DF S\u00F9\u00E7\u00E7\u00EAssf\u00FAll\u00FF S\u00EB\u00F1t [echoproperties] bb.override.list=MP_COPYRIGHTTEXT, "\u00C7\u00F2p\u00FFr\u00ECght 2012 V\u00E8r\u00EDv\u00F3 B\u00F9\u00EEl\u00F0 T\u00E9\u00E0?" [echoproperties] bb.vendor=V\u00E8r\u00ECv\u00F2 [echoproperties] common.app=VrvPsLTst [echoproperties] common.app.LoginButtonText=L\u00F2g\u00EC\u00F1 [echoproperties] common.app.LoginProgressMessage=\u00C0\u00F9th\u00E8\u00F1t\u00EC\u00E7\u00E0t\u00ED\u00F2\u00F1 \u00EE\u00F1 pr\u00F3gr\u00E9ss... [echoproperties] common.app.LoginScreenMessage=W\u00E8l\u00E7\u00F2?\u00E9 M\u00EAss\u00E0g\u00EB [echoproperties] common.app.PasswordText=P\u00E0ssw\u00F2r\u00F0 [echoproperties] common.app.ServerName=http\://V\u00E8r\u00ECv\u00F2.com [echoproperties] common.app.UserIdText=\u00D9s\u00E8r \u00CC\u00D0 [echoproperties] common.app.description=Pseudo Loc Test App for Build Script testing [echoproperties] common.app.name=?? [echoproperties] file.encoding=Cp1252 [echoproperties] file.encoding.pkg=sun.io [echoproperties] file.separator=\\ [echoproperties] ios.RegistrationText=R\u00E8g\u00ECstr\u00E0t\u00ED\u00F2\u00F1 T\u00E9xt [echoproperties] ios.RegistrationURL=http\://www.josscrowcroft.com/2011/code/utf-8-multibyte-characters-in-url-parameters-%E2%9C%93/ [echoproperties] java.awt.graphicsenv=sun.awt.Win32GraphicsEnvironment [echoproperties] java.awt.printerjob=sun.awt.windows.WPrinterJob [echoproperties] java.class.path=c\:\\ant\\bin\\..\\lib\\ant-launcher.jar;C\:\\Temp\\utf8\\.\\;C\:\\Program Files (x86)\\Java\\jre7\\lib\\ext\\QTJava.zip;C\:\\ant\\lib\\ant-antlr.jar;C\:\\ant\\lib\\ant-apache-bcel.jar;C\:\\ant\\lib\\ant-apache-bsf.jar;C\:\\ant\\lib\\ant-apache-log4j.jar;C\:\\ant\\lib\\ant-apache-oro.jar;C\:\\ant\\lib\\ant-apache-regexp.jar;C\:\\ant\\lib\\ant-apache-resolver.jar;C\:\\ant\\lib\\ant-apache-xalan2.jar;C\:\\ant\\lib\\ant-commons-logging.jar;C\:\\ant\\lib\\ant-commons-net.jar;C\:\\ant\\lib\\ant-contrib-1.0b3.jar;C\:\\ant\\lib\\ant-jai.jar;C\:\\ant\\lib\\ant-javamail.jar;C\:\\ant\\lib\\ant-jdepend.jar;C\:\\ant\\lib\\ant-jmf.jar;C\:\\ant\\lib\\ant-jsch.jar;C\:\\ant\\lib\\ant-junit.jar;C\:\\ant\\lib\\ant-launcher.jar;C\:\\ant\\lib\\ant-netrexx.jar;C\:\\ant\\lib\\ant-nodeps.jar;C\:\\ant\\lib\\ant-starteam.jar;C\:\\ant\\lib\\ant-stylebook.jar;C\:\\ant\\lib\\ant-swing.jar;C\:\\ant\\lib\\ant-testutil.jar;C\:\\ant\\lib\\ant-trax.jar;C\:\\ant\\lib\\ant-weblogic.jar;C\:\\ant\\lib\\ant.jar;C\:\\ant\\lib\\bb-ant-tools.jar;C\:\\ant\\lib\\xercesImpl.jar;C\:\\ant\\lib\\xml-apis.jar;C\:\\Program Files\\Java\\jre7\\lib\\tools.jar [echoproperties] java.class.version=51.0 [echoproperties] java.endorsed.dirs=C\:\\Program Files\\Java\\jre7\\lib\\endorsed [echoproperties] java.ext.dirs=C\:\\Program Files\\Java\\jre7\\lib\\ext;C\:\\Windows\\Sun\\Java\\lib\\ext [echoproperties] java.home=C\:\\Program Files\\Java\\jre7 [echoproperties] java.io.tmpdir=C\:\\Users\\efelton\\AppData\\Local\\Temp\\ [echoproperties] java.library.path=C\:\\Windows\\SYSTEM32;C\:\\Windows\\Sun\\Java\\bin;C\:\\Windows\\system32;C\:\\Windows;C\:\\Windows\\SYSTEM32;C\:\\Windows;C\:\\Windows\\SYSTEM32\\WBEM;C\:\\Windows\\SYSTEM32\\WINDOWSPOWERSHELL\\V1.0\\;C\:\\PROGRAM FILES\\INTEL\\WIFI\\BIN\\;C\:\\PROGRAM FILES\\COMMON FILES\\INTEL\\WIRELESSCOMMON\\;C\:\\PROGRAM FILES (X86)\\MICROSOFT SQL SERVER\\100\\TOOLS\\BINN\\;C\:\\PROGRAM FILES\\MICROSOFT SQL SERVER\\100\\TOOLS\\BINN\\;C\:\\PROGRAM FILES\\MICROSOFT SQL SERVER\\100\\DTS\\BINN\\;C\:\\PROGRAM FILES (X86)\\MICROSOFT SQL SERVER\\100\\TOOLS\\BINN\\VSSHELL\\COMMON7\\IDE\\;C\:\\PROGRAM FILES (X86)\\MICROSOFT SQL SERVER\\100\\DTS\\BINN\\;C\:\\Program Files\\ThinkPad\\Bluetooth Software\\;C\:\\Program Files\\ThinkPad\\Bluetooth Software\\syswow64;C\:\\Program Files (x86)\\QuickTime\\QTSystem\\;C\:\\Program Files (x86)\\AccuRev\\bin;C\:\\Program Files\\Java\\jdk1.7.0_04\\bin;C\:\\Program Files (x86)\\IDM Computer Solutions\\UltraEdit\\;. [echoproperties] java.runtime.name=Java(TM) SE Runtime Environment [echoproperties] java.runtime.version=1.7.0_04-b22 [echoproperties] java.specification.name=Java Platform API Specification [echoproperties] java.specification.vendor=Oracle Corporation [echoproperties] java.specification.version=1.7 [echoproperties] java.vendor=Oracle Corporation [echoproperties] java.vendor.url=http\://java.oracle.com/ [echoproperties] java.vendor.url.bug=http\://bugreport.sun.com/bugreport/ [echoproperties] java.version=1.7.0_04 [echoproperties] java.vm.info=mixed mode [echoproperties] java.vm.name=Java HotSpot(TM) 64-Bit Server VM [echoproperties] java.vm.specification.name=Java Virtual Machine Specification [echoproperties] java.vm.specification.vendor=Oracle Corporation [echoproperties] java.vm.specification.version=1.7 [echoproperties] java.vm.vendor=Oracle Corporation [echoproperties] java.vm.version=23.0-b21 [echoproperties] line.separator=\r\n [echoproperties] os.arch=amd64 [echoproperties] os.name=Windows 7 [echoproperties] os.version=6.1 [echoproperties] path.separator=; [echoproperties] sun.arch.data.model=64 [echoproperties] sun.boot.class.path=C\:\\Program Files\\Java\\jre7\\lib\\resources.jar;C\:\\Program Files\\Java\\jre7\\lib\\rt.jar;C\:\\Program Files\\Java\\jre7\\lib\\sunrsasign.jar;C\:\\Program Files\\Java\\jre7\\lib\\jsse.jar;C\:\\Program Files\\Java\\jre7\\lib\\jce.jar;C\:\\Program Files\\Java\\jre7\\lib\\charsets.jar;C\:\\Program Files\\Java\\jre7\\lib\\jfr.jar;C\:\\Program Files\\Java\\jre7\\classes [echoproperties] sun.boot.library.path=C\:\\Program Files\\Java\\jre7\\bin [echoproperties] sun.cpu.endian=little [echoproperties] sun.cpu.isalist=amd64 [echoproperties] sun.desktop=windows [echoproperties] sun.io.unicode.encoding=UnicodeLittle [echoproperties] sun.java.command=org.apache.tools.ant.launch.Launcher -cp .;C\:\\Program Files (x86)\\Java\\jre7\\lib\\ext\\QTJava.zip [echoproperties] sun.java.launcher=SUN_STANDARD [echoproperties] sun.jnu.encoding=Cp1252 [echoproperties] sun.management.compiler=HotSpot 64-Bit Tiered Compilers [echoproperties] sun.os.patch.level=Service Pack 1 [echoproperties] user.country=US [echoproperties] user.dir=C\:\\Temp\\utf8 [echoproperties] user.home=C\:\\Users\\efelton [echoproperties] user.language=en [echoproperties] user.name=efelton [echoproperties] user.script= [echoproperties] user.timezone= [echoproperties] user.variant= BUILD SUCCESSFUL Total time: 1 second Thank you for your help EDIT\UPDATE 6/19/2012 I am developing in a Windows environment. I have installed a TTF from: http://freedesktop.org/wiki/Software/CJKUnifonts/Download I have updated UltraEdit to use the TTF and I can see the Chinese characters. <?xml version="1.0" encoding="UTF-8" ?> <project name="utf8test" default="all" basedir="."> <target name="all"> <echo>??</echo> <echo encoding="ISO-8859-1">ISO-8859-1 ??</echo> <echo encoding="UTF-8">UTF-8 ??</echo> <echo file="echo_output.txt" append="true" >?? ${line.separator}</echo> <echo file="echo_output.txt" append="true" encoding="ISO-8859-1">ISO-8859-1 ?? ${line.separator}</echo> <echo file="echo_output.txt" append="true" encoding="UTF-8">UTF-8 ?? ${line.separator}</echo> <echo file="echo_output.txt" append="true" encoding="UnicodeLittle">UnicodeLittle ?? ${line.separator}</echo> <echo file="echo_output.txt" append="true" encoding="UnicodeLittleUnmarked">UnicodeLittleUnmarked ?? ${line.separator}</echo> </target> </project> The output captured by running inside UltraEdit is: Buildfile: E:\temp\utf8\build.xml all: [echo] ?? [echo] ISO-8859-1 ?? [echo] UTF-8 ?? BUILD SUCCESSFUL Total time: 1 second And the echo_output.txt file shows up like this: ?? ISO-8859-1 ?? UTF-8 ?? ÿþU n i c o d e L i t t l e ? ? U n i c o d e L i t t l e U n m a r k e d ? ? So there appears to be somehting fundamentally wrong with how my ANT environment is set up since I cannot simply echo the character to the screen or to a file.

    Read the article

  • How to persist options selected in AlertDialog spawned from ItemizedOverlay onTap method

    - by ahsteele
    In the description of how to add a list of options to an AlertDialog the official Android documentation alludes to saving a users preferences with one of the "data storage techniques." The examples assume the AlertDialog has been spawned within an Activity class. In my case I've created a class that extends ItemizedOverlay. This class overrides the onTap method and uses an AlertDialog to prompt the user to make a multi-choice selection. I would like to capture and persist the selections for each OverlayItem they tap on. The below code is the onTap method I've written. It functions as written but doesn't yet do what I'd hope. I'd like to capture and persist each selection made by the user to be used later. How do I do that? Is using an AlertDialog in this manner a good idea? Are there better options? protected boolean onTap(int index) { OverlayItem item = _overlays.get(index); final CharSequence[] items = { "WiFi", "BlueTooth" }; final boolean[] checked = { false, false }; AlertDialog.Builder builder = new AlertDialog.Builder(_context); builder.setTitle(item.getTitle()); builder.setMultiChoiceItems(items, checked, new DialogInterface.OnMultiChoiceClickListener() { @Override public void onClick(DialogInterface dialog, int item, boolean isChecked) { // for now just show that the user touched an option Toast.makeText(_context, items[item], Toast.LENGTH_SHORT).show(); } }); builder.setPositiveButton("Okay", new DialogInterface.OnClickListener() { @Override public void onClick(DialogInterface dialog, int id) { // should I be examining what was checked here? dialog.dismiss(); } }); builder.setNegativeButton("Cancel", new DialogInterface.OnClickListener() { @Override public void onClick(DialogInterface dialog, int id) { dialog.cancel(); } }); AlertDialog alert = builder.create(); alert.show(); return true; }

    Read the article

  • blackberry smartcard reader example

    - by pajton
    I am writing an app for BlackBerry that utilizes a BlackBerry smartcard reader. There is not much documentation on the subject, so I'd really like if someone could give me starting examples. Basically, there is one RSA private key on the card plus a certificate (for paired public key). I would like to be able to encrypt/decrypt data and also sign it as well. The final goal would be to establish an mutual-authenticated SSL connection using client certificate contained on the smartcard. Here is the code I managed to come up with so far: SmartCardReader btReader = null; SmartCardReader[] readers = SmartCardReaderFactory.getInstalledReaders(); for (int i = 0; i < readers.length; i++) { SmartCardReader reader = readers[i]; if (reader.getType().equalsIgnoreCase("bluetooth")) { btReader = reader; break; } } SmartCardReaderSession readerSession = reader.openSession(); CryptoSmartCard card = (CryptoSmartCard) readerSession.getSmartCard(); RSACryptoToken token = (RSACryptoToken) card.getCryptoToken("RSA"); This token looks promising - has some nice methods, but with "cryptic" arguments. What to do next?

    Read the article

  • Why is WMDC/ActiveSync so flaky?

    - by Ira Rainey
    I'm developing a Windows Mobile app using the .NET Compact Framework 3.5 and VS2008, and for debugging using the Device Emulator V3, on Win7, and seem to have constant problems with Windows Mobile Device Centre (6.1) connecting. Using the Emulator Manager (9.0.21022.8) I cradle the device using DMA in WMDC. The problem is it's so flaky at actually connecting that it's becoming a pain. I find that when I turn my computer on, before I can get it to connect I have to open up WMDC, disable Connect over DMA, close WMDC down, reopen it again, and then it might cradle. Often I have to do this twice before it will cradle. Once it's cradled it's generally fine, but nothing seems consistent in getting it to connect. Connecting with physical devices is often better, although not always. If I plug a PDA into a USB socket other than the one it was originally plugged into then it won't connect at all. Often the best/most reliable connection method seems to be over Bluetooth, but that's quite slow. Anybody got any tips or advice?

    Read the article

  • Save options selected in AlertDialog spawned from ItemizedOverlay onTap method

    - by ahsteele
    In the description of how to add a list of options to an AlertDialog the official Android documentation alludes to saving a users preferences with one of the "data storage techniques." The examples assume the AlertDialog has been spawned within an Activity class. In my case I've created a class that extends ItemizedOverlay. This class overrides the onTap method and uses an AlertDialog to prompt the user to make a multi-choice selection. I would like to capture and persist the selections for each OverlayItem they tap on. That said I am unsure if utilizing an AlertDialog in this manner is the right approach and open to other suggestions. protected boolean onTap(int index) { OverlayItem item = _overlays.get(index); final CharSequence[] items = { "WiFi", "BlueTooth" }; final boolean[] checked = { false, false }; AlertDialog.Builder builder = new AlertDialog.Builder(_context); builder.setTitle(item.getTitle()); builder.setMultiChoiceItems(items, checked, new DialogInterface.OnMultiChoiceClickListener() { @Override public void onClick(DialogInterface dialog, int item, boolean isChecked) { // for now just show that the user touched an option Toast.makeText(_context, items[item], Toast.LENGTH_SHORT).show(); } }); builder.setPositiveButton("Okay", new DialogInterface.OnClickListener() { @Override public void onClick(DialogInterface dialog, int id) { // should I be examining what was checked here? dialog.dismiss(); } }); builder.setNegativeButton("Cancel", new DialogInterface.OnClickListener() { @Override public void onClick(DialogInterface dialog, int id) { dialog.cancel(); } }); AlertDialog alert = builder.create(); alert.show(); return true; }

    Read the article

  • C# .Net Serial DataReceived Event response too slow for high-rate data.

    - by Matthew
    Hi, I have set up a SerialDataReceivedEventHandler, with a forms based program in VS2008 express. My serial port is set up as follows: 115200, 8N1 Dtr and Rts enabled ReceivedBytesThreshold = 1 I have a device I am interfacing with over a BlueTooth, USB to Serial. Hyper terminal receives the data just fine at any data rate. The data is sent regularly in 22 byte long packets. This device has an adjustable rate at which data is sent. At low data rates, 10-20Hz, the code below works great, no problems. However, when I increase the data rate past 25Hz, there starts to recieve mulitple packets on one call. What I mean by this is that there should be a event trigger for every incoming packet. With higher output rates, I have tested the buffer size (BytesToRead command) immediatly when the event is called and there are multiple packets in the buffer then. I think that the event fires slowly and by the time it reaches the code, more packes have hit the buffer. One test I do is see how many time the event is trigger per second. At 10Hz, I get 10 event triggers, awesome. At 100Hz, I get something like 40 event triggers, not good. My goal for data rate is 100HZ is acceptable, 200Hz preferred, and 300Hz optimum. This should work because even at 300Hz, that is only 52800bps, less than half of the set 115200 baud rate. Anything I am over looking? public Form1() { InitializeComponent(); serialPort1.DataReceived += new SerialDataReceivedEventHandler(serialPort1_DataReceived); } private void serialPort1_DataReceived(object sender, SerialDataReceivedEventArgs e) { this.Invoke(new EventHandler(Display_Results)); } private void Display_Results(object s, EventArgs e) { serialPort1.Read(IMU, 0, serial_Port1.BytesToRead); }

    Read the article

  • Tablet interface for the physically disabled?

    - by Glenn
    My sister has Cerebral Palsy, which in her case means she has only gross motor control and her speech is slurred. Implications should be obvious: traditional computer/phone/tablet interfaces won't work for her and she can't speak clearly enough for speech recognition software to help her at all. She enjoys reading but has difficulty holding the book and/or turning a page. There are a few options for helping her use a computer, but nothing for tablets or eReaders. That's where you come in. I would like to make (or buy, if such a thing exists) a better interface to an Android tablet that would work for someone with little to no physical dexterity or speech ability. I'd also be interested in work on the Kindle or iPad, but I'm most familiar with Android so I'm starting there. I know Android has Bluetooth capability. Is it possible to interface a joystick to control the Android device? By "control", I mean the entire operating system - selecting an app, launching it, controlling the menus, etc. I want to give her control over the whole thing, not just a specific app. On a PC this can be accomplished by creating a generic USB HID interface and an arcade joystick to move the mouse over the screen and click on thigns. Is it possible to do something like that in Android? Any help you can offer would be greatly appreciated. Thanks!

    Read the article

  • Low-level Keyboard Hooks/SendInput with Winkey+L possible? (workstation lockout is intercepted in Vi

    - by Brian Jorgensen
    I work on a project called UAWKS (Unofficial Apple Wireless Keyboard Support) that helps Windows users use Apple's bluetooth keyboard. One of the main goals of UAWKS is to swap the Cmd key (which behaves as Winkey in Windows) with Ctrl, allowing users to do Cmd+C for copy, Cmd+T for new tab, etc. It is currently developed using AutoHotkey, which worked pretty well under Windows XP. However, on Vista and Windows 7, Cmd+L causes problems: Regardless of low-level keyboard hooks, Winkey+L is always intercepted by Windows and normally locks the workstation... You can disable workstation locking with this registry hack, but pressing Winkey+L still can't be rebound in AHK Pressing Winkey+L leaves Winkey in the Keydown state until the next (additional) Winkey Up. Simulating a Keyup event doesn't seem to work either! It seems that Winkey+L is a special chord that messes everything else up. I've looked through the AHK source code, and they try to address this problem in SendKey() in keyboard_mouse.cpp (near line 883 in v1.0.48.05), but it doesn't work. I wrote up my own low-level keyboard hook application in C#, and I see the same problem. Has anyone else run into this? Is there a workaround?

    Read the article

  • Graphics driver for ubuntu on dell latitude XT

    - by marc.riera
    Hi, we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

    Read the article

  • Graphics driver for ubuntu on dell latitude XT

    - by marc.riera
    we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

    Read the article

  • No login prompt displayed after updating Ubuntu 10.04, broken gdm

    - by cliff
    So here's what happens: I updated my system the other day, was prompted for a reboot for the update to complete but was in the middle of working so I delayed it until after I was done. I reboot and it's broken :(. It appears to boot normally, with the following exceptions: The purple Ubuntu load screen no longer displays (though it did for the first couple of times I tried to get in). I hear the login prompt sound, but no login prompt appears. Nor is it simply "invisible" - pressing enter, typing my password, and pressing enter again do nothing. Normally my Bluetooth mouse is functional at this point, but it is not. GRUB displays recovery options for my current kernel, and for an older one (2.6.32-24). Trying to boot into .32-24 gives me an error saying "udevadm can't do something while udev is not configured". So I try solutions listed here: http://superuser.com/questions/195786/ubuntu-update-went-wrong-pc-doesnt-boot-how-can-i-repair-it Nothing I tried seemed to work, and after further Googling my hunch is that it's a problem with gdm. Please correct me if I'm wrong, I don't know all that much about how Linux/Ubuntu systems work just yet. Things I'm able to do: Boot to a live CD Ctrl-Alt-F2 after that login sound plays brings me to a console login, which I can successfully do (it's how I tried the solutions above). This works only under the current kernel. A hack I'd be willing to explore is removing the login prompt from the console, but I'd prefer to "simply" fix what's wrong. Like that guy, I need to repair the system rather than reinstall. System: Dell Inspiron 1525 Core 2 Duo Proprietary Driver for Broadcom 43xx wireless Dual-boot with Windows 7 (which is how I'm posting this, unfortunately I only have this machine and any experimenting requires constant reboots into Windows/brokenbuntu) Last package installed was Moonlight, but it appeared to install properly. Kernel: 2.6.32-25 Edit: After working with Karl's suggestions, it seems that the problem is with gdm. Error exit status 245 when attempting to sudo apt-get install --reinstall gdm, also an error processing gdm when running sudo apt-get -f install. How do I reinstall or repair gdm so that I can get back into my machine?

    Read the article

  • Hell: NTFS "Restore previous versions"...

    - by ttsiodras
    The hell I have experienced these last 24h: Windows 7 installation hosed after bluetooth driver install. Attempting to recover using restore points via "Repair" on the bootable Win7 installation CD. Attempting to go back one day in the restore points. No joy. Attempting to go back two days in the restore points. No joy. Attempting to go back one week in the restore points. Stil no joy. Windows won't boot. Apparently something is REALLY hosed. And then it hits me - PANIC - the restore points somehow reverted DATA files to their older versions! Word, Powerpoint, SPSS, etc document versions are all one week old now. Using the "freshest" restore point. Failed to restore yesterday's restore point!!! I am stuck at old versions of the data!!! Booting KNOPPIX, mounting NTFS partition as read-only under KNOPPIX. Checking. Nope, the data files are still the one week old versions. Booting Win7 CD, Recovery console - Cmd prompt - navigating - yep, data files are still one week old. Removing the drive, mounting it under other Win7 installation. Still old data. Running NTFS undelete on the drive (read-only scan), searching for file created yesterday. Not found. Despair. At this point, idea: I will install a brand new Windows installation, keeping the old one in Windows.old (default behaviour of Windows installs). I boot the new install, I go to my C:\Data\ folder, I choose "Restore previous versions", click on yesterday's date, and click open... YES! It works! I can see the latest versions of my files (e.g. from yesterday). Thank God. And then, I try to view the files under the "yesterday snapshot-version" of c:\Users\MyAccount\Desktop ... And I get "Permission Denied" as soon as I try to open "Users\MyAccount". I make sure I am an administrator. No joy. Apparently, the new Windows installation does not have access to read the "NTFS snapshots" or "Volume Shadow Snapshots" of my old Windows account! Cross-installation permissions? I need to somehow tell the new Windows install that I am the same "old" user... So that I will be able to access the "Users\MyAccount" folder of the snapshot of my old user account. Help?

    Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39  | Next Page >