Search Results

Search found 13331 results on 534 pages for 'fluent interface'.

Page 35/534 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

• iptables forwarding to a dummy interface

  - by madinc

  Hi, I'm trying to accomplish the following: I have a box with a service listening on a dummy interface (say 172.16.0.1), udp port 5555. Now what I'd like to do is to take packets that arrive on interfaces eth0 (1.1.1.1:5555) and eth1 (2.2.2.2:5555) and forward them to the service on the dummy interface, and have replies go back to clients out the same physical interface they came in. Clients must think they're talking to 1.1.1.1:5555 or 2.2.2.2:5555. I think I need a mix of iptables rules and packet marking, plus some iproute rules (if it's possible at all). What I tried is to catch packets coming in from eth0 and eth1, udp port 5555, and mark them with 1 and 2 respectively, and --save-mark in the connmark. Then I used a DNAT to 172.16.0.1. The service seems to be getting the packets. Now I'm not sure how to do the reverse. It seems that for packets originating from the box, you can't do anything before the routing decision, but that would be the place to restore the marks, and thus make a routing decision based on those. Here's what I have so far: iptables -t mangle -A PREROUTING -d 1.1.1.1 -p udp --port 5555 -j MARK --set-mark 1 iptables -t mangle -A PREROUTING -d 2.2.2.2 -p udp --port 5555 -j MARK --set-mark 2 iptables -t mangle -A PREROUTING -d 1.1.1.1 -p udp --port 5555 -j CONNMARK --save-mark iptables -t mangle -A PREROUTING -d 2.2.2.2 -p udp --port 5555 -j CONNMARK --save-mark iptables -t nat -A PREROUTING -m mark --mark 1 -j DNAT --to-destination 172.16.0.1 iptables -t nat -A PREROUTING -m mark --mark 2 -j DNAT --to-destination 172.16.0.1 # What next? As I said, I'm not even sure it can be done. To give a bit of background, it's an old OpenVPN installation that cannot be upgraded (otherwise I'd install a recent version that supports multihoming natively). Thanks for any help.

  Read the article

• Vyatta masquerade out bridge interface

  - by miquella

  We have set up a Vyatta Core 6.1 gateway on our network with three interfaces: eth0 - 1.1.1.1 - public gateway/router IP (to public upstream router) eth1 - 2.2.2.1/24 - public subnet (connected to a second firewall 2.2.2.2) eth2 - 10.10.0.1/24 - private subnet Our ISP provided the 1.1.1.1 address for us to use as our gateway. The 2.2.2.1 address is so the other firewall (2.2.2.2) can communicate to this gateway which then routes the traffic out through the eth0 interface. Here is our current configuration: interfaces { bridge br100 { address 2.2.2.1/24 } ethernet eth0 { address 1.1.1.1/30 vif 100 { bridge-group { bridge br100 } } } ethernet eth1 { bridge-group { bridge br100 } } ethernet eth2 { address 10.10.0.1/24 } loopback lo { } } service { nat { rule 100 { outbound-interface eth0 source { address 10.10.0.1/24 } type masquerade } } } With this configuration, it routes everything, but the source address after masquerading is 1.1.1.1, which is correct, because that's the interface it's bound to. But because of some of our requirements here, we need it to source from the 2.2.2.1 address instead (what's the point of paying for a class C public subnet if the only address we can send from is our gateway!?). I've tried binding to br100 instead of eth0, but it doesn't seem to route anything if I do that. I imagine I'm just missing something simple. Any thoughts?

  Read the article

• Separated virtual networks with same subnet range with 2 interface

  - by Coolpet

  I'm having some problems with routing with the following: I have a server with 2 interfaces. It has 1-1 alias contains the same subnet. the 2 interface is connected to 2 switch, which are separated from each other. Infrastructure: Eth0 192.168.16.2/20 Eth0:eth0 192.168.1.222/20 Eth1 192.168.32.3/20 Eth1:eth1 192.168.1.223/20 I have a PC which has the IP address: 192.168.1.3/24 The problem is the next: If PC is on subnet 1, I can ping it. If PC is on subnet 2, I can't ping it. traceroute shows the route is across 192.168.1.222 ping -I 192.168.1.223 192.168.1.3 is not working on subnet 2. arp entries show the MAC address belonging to the correct interface (eth1 on subnet 2) How can I force the server to look on both interface same ranged subnet for specific IP? It searches only in the first subnet. The routing table has these 2 entries: 192.168.0.0/20 dev eth0 proto kernel scope link src 192.168.1.222 192.168.0.0/20 dev eth1 proto kernel scope link src 192.168.1.223

  Read the article

• Using FluentNHibernate + SQLite with .Net4?

  - by stiank81

  I have a WPF application running with .Net3.5 using FluentNHibernate, and all works fine. When I upgraded to VS2010 I ran into some odd problems, but after changing to use x64 variant of SQLite it worked fine again. Now I want to change to use .Net4, but this has turned into a more painful experience then I expected.. When calling FluentConfiguration.BuildConfiguration I get an exception thrown: FluentConfigurationException unhandled An invalid or incomplete configuration was used while creating a SessionFactory. Check PotentialReasons collection, and InnerException for more detail The inner exception gives us more information: Message = "Could not create the driver from NHibernate.Driver.SQLite20Driver, NHibernate, Version=2.1.2.4000, Culture=neutral, PublicKeyToken=aa95f207798dfdb4." It has an InnerException again: Exception has been thrown by the target of an invocation. Which again has an InnerException: The IDbCommand and IDbConnection implementation in the assembly System.Data.SQLite could not be found. Ensure that the assembly System.Data.SQLite is located in the application directory or in the Global Assembly Cache. If the assembly is in the GAC, use element in the application configuration file to specify the full name of the assembly. Now - to me it sounds like it doesn't find System.Data.SQLite.dll, but I can't understand this. Everywhere this is referenced I have "Copy Local", and I have verified that it is in every build folder for projects using SQLite. I have also copied it manually to every Debug folder of the solution - without luck. Notes: This exact same code worked just fine before I upgraded to .Net4. I did see some x64 x86 mismatch problems earlier, but I have switched to use x86 as the target platform and for all referenced dlls. I have verified that all files in the Debug-folder are x86. I have tried the precompiled Fluent dlls, I have tried compiling myself, and I have compiled my own version of Fluent using .Net4. I see that there are also others that have seen this problem, but I haven't really seen any solution yet. After @devio's answer I tried adding a reference to the SQLite dll. This didn't change anything, but I hope I made it right though.. This is what I added to the root node of the app.config file: <runtime> <assemblyBinding xmlns="urn:schemas-microsoft-com:asm.v1"> <qualifyAssembly partialName="System.Data.SQLite" fullName="System.Data.SQLite, Version=1.0.60.0, Culture=neutral, PublicKeyToken=db937bc2d44ff139" /> </assemblyBinding> </runtime> Anyone out there using Fluent with .Net4 and SQLite successfully? Help! I'm lost...

  Read the article

• Problems using FluentNHibernate + SQLite with .NET4?

  - by stiank81

  I have a WPF application running with VS2010 .Net3.5 using Nhibernate with FluentNHibernate + SQLite, and all works fine. Now I want to change to use .Net4, but this has turned into a more painful experience then I expected.. When setting up the connection a FluentConfigurationException is thrown from FluentConfiguration.BuildConfiguration saying: An invalid or incomplete configuration was used while creating a SessionFactory. Check PotentialReasons collection, and InnerException for more details. The inner exception gives us more information: Could not create the driver from NHibernate.Driver.SQLite20Driver, NHibernate, Version=2.1.2.4000, Culture=neutral, PublicKeyToken=aa95f207798dfdb4. It has an InnerException again: Exception has been thrown by the target of an invocation. Which again has an InnerException: The IDbCommand and IDbConnection implementation in the assembly System.Data.SQLite could not be found. Ensure that the assembly System.Data.SQLite is located in the application directory or in the Global Assembly Cache. If the assembly is in the GAC, use element in the application configuration file to specify the full name of the assembly. Now - to me it sounds like it doesn't find System.Data.SQLite.dll, but I can't understand this. Everywhere this is referenced I have "Copy Local", and I have verified that it is in every build folder for projects using SQLite. I have also copied it manually to every Debug folder of the solution - without luck. Notes: This is exactly the same code that worked just fine before I upgraded to .Net4. I did see some x64 x86 mismatch problems earlier, but I have switched to use x86 as the target platform and for all referenced dlls. I have verified that all files in the Debug-folder are x86. I have tried the precompiled Fluent dlls, I have tried compiling myself, and I have compiled my own version of Fluent using .Net4. I see that there are also others that have seen this problem, but I haven't really seen any solution yet. After @devio's answer I tried adding a reference to the SQLite dll. This didn't change anything, but I hope I made it right though.. This is what I added to the root node of the app.config file: <runtime> <assemblyBinding xmlns="urn:schemas-microsoft-com:asm.v1"> <qualifyAssembly partialName="System.Data.SQLite" fullName="System.Data.SQLite, Version=1.0.60.0, Culture=neutral, PublicKeyToken=db937bc2d44ff139" /> </assemblyBinding> </runtime> Anyone out there using Fluent with .Net4 and SQLite successfully? Help! I'm lost...

  Read the article

• Can extension methods be applied to interfaces?

  - by Greg

  Hi, Is it possible to apply an extension method to an interface? (C# question) That is for example to achieve the following: create an ITopology interface create an extension method for this interface (e.g. public static int CountNodes(this ITopology topologyIf) ) then when creating a class (e.g. MyGraph) which implements ITopology, then it would automatically have the Count Nodes extension. This way the classes implementing the interface would not have to have a set class name to align with what was defined in the extension method.

  Read the article

• FluentNhibernate dynamic runtime mappings.

  - by Paul Knopf

  I am building a framework where people will be able to save items that the created by inheriting a class of mine. I will be iterating over every type in the appdomain to find classes that I want to map to nhibernate. Every class that I find will be a subclass of the inherited type. I know how to create sub types in FluentNhibernate, but every sub type requires its own ClassMap class. Since I won't know these untill runtime, there is no way I can do that. Is there a way that I can add mappings to fluent nhibernate? Note, I know this is possible without fluent nhibernate using the Cfg class, but I don't want to manage the same code two different ways.

  Read the article

• fluent nhibernate not caching queries in asp.net mvc

  - by AWC

  I'm using a fluent nhibernate with asp.net mvc and I not seeing anything been cached when making queries against the database. I'm not currently using an L2 cache implementation. Should I see queries being cached without configuring an out of process L2 cache? Mapping are like this: Table("ApplicationCategories"); Not.LazyLoad(); Cache.ReadWrite().IncludeAll(); Id(x => x.Id); Map(x => x.Name).Not.Nullable(); Map(x => x.Description).Nullable(); Example Criteria: return session .CreateCriteria<ApplicationCategory>() .Add(Restrictions.Eq("Name", _name)) .SetCacheable(true); Everytime I make a request for an application cateogry by name it is hitting the database is this expected behaviour?

  Read the article

• When using Dependency Injection with StructureMap how do I chooose among multiple constructors?

  - by Mark Rogers

  I'm trying to get structuremap to build Fluent Nhibernate's SessionSource object for some of my intregration tests. The only problem is that Fluent's concrete implementation of ISessionSource (SessionSource) has 3 constructors: public SessionSource(PersistenceModel model) { Initialize(new Configuration().Configure(), model); } public SessionSource(IDictionary<string, string> properties, PersistenceModel model) { Initialize(new Configuration().AddProperties(properties), model); } public SessionSource(FluentConfiguration config) { configuration = config.Configuration; sessionFactory = config.BuildSessionFactory(); dialect = Dialect.GetDialect(configuration.Properties); } I've tried configuring my ObjectFactory supplying an argument for the first constructor but it seems like it wants to try the second one. How do I configure my ObjectFactory so that I can choose the first constructor or perhaps even another one if I decide to use that?

  Read the article

• Items Created via IB are not being displayed

  - by Rohan

  Hello, This is what i have done so far, Made a Custom view added few objects, as shown below @interface CommUICustomSignInView : CommUICustomView { IBOutlet NSButton *pBtn; IBOutlet NSTextField *pTextField; NSTrackingArea *pTrackingArea; NSCursor *pPonitHandCursor; } Added all IBoutlet correctly, Now thru Interface builder constructed a Window controller interface builder in which added a custom view and provided this class name in the interface builder, I hope i could able to visualize you guys, now whenever i loaded this view, the item whatever i created by IB are not being displayed, Am i doing something wrong, or something missing,

  Read the article

• How to implement fluent interface with a base class, in C++

  - by Vincenzo

  How can I implement this fluent interface in C++: class Base { public: Base& add(int x) { return *this; } } class Derived : public Base { public: Derived& minus(int x) { return *this; } } Derived d; d.add(1).minus(2).add(3).minus(4); Current code doesn't work since Base class doesn't know anything about Derived class, etc. I would be very thankful for a hint/suggestion.

  Read the article

• Simple Cisco ASA 5505 config issue

  - by Ben Sebborn

  I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

  Read the article

• WCF <operation>Async methods not generated in proxy interface

  - by Charlie

  I want to use the Asnyc methods rather than the Begin on my WCF service client proxy because I'm updating WPF controls and need to make sure they're being updated from the UI thread. I could use the Dispatcher class to queue items for the UI thread but that's not what I'm asking about.. I've configured the service reference to generate the asynchronous operations, but it only generates the methods in proxy's implementation, not it's interface. The interface only contains syncronous and Begin methods. Why aren't these methods generated in the interface and is there a way to do this, or do I have to create a derived interface to manually add them?

  Read the article

• OpenIndiana (illumos): vmxnet3 interface lost on reboot

  - by protomouse

  I want my VMware vmxnet3 interface to be brought up with DHCP on boot. I can manually configure the NIC with: # ifconfig vmxnet3s0 plumb # ipadm create-addr -T dhcp vmxnet3s0/v4dhcp But after creating /etc/dhcp.vmxnet3s0 and rebooting, the interface is down and the logs show: Aug 13 09:34:15 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:15 neumann vmxnet3s: [ID 715698 kern.notice] vmxnet3s:0: stop() Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:17 neumann vmxnet3s: [ID 920500 kern.notice] vmxnet3s:0: start() Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(TxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxBufPoolLimit) -> 512 Aug 13 09:34:17 neumann nwamd[491]: [ID 605049 daemon.error] 1: nwamd_set_unset_link_properties: dladm_set_linkprop failed: operation not supported Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x20000) -> no Aug 13 09:34:17 neumann nwamd[491]: [ID 751932 daemon.error] 1: nwamd_down_interface: ipadm_delete_addr failed on vmxnet3s0: Object not found Aug 13 09:34:17 neumann nwamd[491]: [ID 819019 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv4 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 160156 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv6 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 771489 daemon.error] 1: add_ip_address: ipadm_create_addr failed on vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 405346 daemon.error] 9: start_dhcp: ipadm_create_addr failed for vmxnet3s0: Operation not supported on disabled object I then tried disabling network/physical:nwam in favour of network/physical:default. This works, the interface is brought up but physical:default fails and my network services (e.g. NFS) refuse to start. # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vmxnet3s0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:1: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:2: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:3: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:4: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:5: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:6: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:7: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:8: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 vmxnet3s0: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 9000 index 2 inet6 ::/0 # cat /var/svc/log/network-physical\:default.log [ Aug 16 09:46:39 Enabled. ] [ Aug 16 09:46:41 Executing start method ("/lib/svc/method/net-physical"). ] [ Aug 16 09:46:41 Timeout override by svc.startd. Using infinite timeout. ] starting DHCP on primary interface vmxnet3s0 ifconfig: vmxnet3s0: DHCP is already running [ Aug 16 09:46:43 Method "start" exited with status 96. ] NFS server not running: # svcs -xv network/nfs/server svc:/network/nfs/server:default (NFS server) State: offline since August 16, 2012 09:46:40 AM UTC Reason: Service svc:/network/physical:default is not running because a method failed. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:default Reason: Service svc:/network/physical:nwam is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:nwam Reason: Service svc:/network/nfs/nlockmgr:default is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/network/nfs/nlockmgr:default See: man -M /usr/share/man -s 1M nfsd Impact: This service is not running. I'm new to the world of Solaris, so any help solving would be much appreciated. Thanks!

  Read the article

• ASP.NET MVC 1 and 2 on Mono 2.4 with Fluent NHibernate

  - by SztupY

  Hi! I'd like to create an application using ASP.NET MVC, that should run under mono 2.4 (compiling will be done on a Windows box). Has anyone getting luck with this? Here is what I've already tried: ASP.NET MVC on mono without any persistence model support, and using nhaml as the view engine S#aml architecture, which is a quite good framework imho, but it depends too much on stuff, that are not working good under mono (like windsor) The first part worked fine, I didn't encounter any major problems. But I couldn't get the second part working. It seems it's dependency on Castle.Windsor breaks the whole mono support (but there might be other parts too). Therefore I decided to create an alternative framework, that borrows some of the ideas of s#arp-architecture, but designed to be working under mono (and if I'm able to do this I'll release it for the community of course). The controller and view part is working fine (not much magic here though, they have been always working), but I have some questions before I start job on the persistence part: What NHibernate versions are working under mono? I've heard 1.2 is working fine. Does 2.0.1/2.1 beta work under mono? Does Fluent.NHibernate and NHibernate.Linq work under mono? (for the latter it seems it needs some dependcies that aren't avaialable in mono) Are there any good alternatives for persistence support to NHibernate under mono? Alternative questions: Are there any frameworks that have mono+persistence+asp.net mvc support already or am I the first one to think about this? If you have already done this: what are your opinions on stability/usability? Thanks for the answers EDIT: Updated the framework to support ASP.NET MVC 2: http://shaml.sztupy.hu/

  Read the article

• Sonicwall with failover, multiple subnets, and preferred WAN interface per subnet

  - by Dan

  I am trying to set up my Sonicwall TZ-210 as follows: Two WAN interfaces (different ISPs), set up in failover mode. Two LAN interfaces with different subnets Each LAN subnet will have a preferred outbound WAN interface, but would failover when necessary. In this way, each ISP is being used for a separate subnet of my network, but both subnets could failover to the other ISP if their primary went down. I know how to do 1 and 2, but I don't know how to do 3. I could set up a route for each subnet to go through a specific interface, but what would happen in the event of a failover? Would it automatically update those routes? Thanks!

  Read the article

• pfSense 2.1 OpenVPN client not using tunnelled interface

  - by Brian M. Hunt

  I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

  Read the article

• Get CLSID by PIA interface Type

  - by Charles

  How can I get the CLSID for a given interface within a Primary Interop Assembly? Here's what I'm talking about: // The c# compiler does some interesting magic. // The following code ... var app = new Microsoft.Office.Interop.Outlook.Application(); // ... is compiled like so (disassembled with Reflector): var app =((Microsoft.Office.Interop.Outlook.Application) Activator.CreateInstance(Type.GetTypeFromCLSID(new Guid("0006F03A-0000-0000-C000-000000000046")))); Microsoft.Office.Interop.Outlook.Application is an interface, and therefore it cannot be instantiated directly. What's interesting here is that c# lets you treat these COM interfaces as if there where classes that you can instantiate with the new keyword. What I want to know is, given the System.Type for a given interface, how can I get the CLSID? Note: I ultimately want to be able to create an instance given the interface's System.Type - I don't really care how. I'm assuming here that the easiest way to do this would be to get CLSID given the Type, just as the c# compiler does.

  Read the article

• ifconfig return "unknown interface: no such device"

  - by xolstice

  I'm trying to install a Linux driver for my wireless network card (D-Link DWL-G510) on my Red Hat Linux 7.1 machine with a 2.4.37.9 kernel. I downloaded the serial monkey driver from the sourceforge site and was able to successfully compile the rt73 module and load it into the kernel. The problem now is that everytime I issue the command ifconfig wlan0 up it keeps returning with the following error message: wlan0: unknown interface: No such device. I'm at a loss as to what to do here. I specifed wlan0 as the alias for the rt73 module in the modules.conf and also tried to load the driver with the command modprobe rt73 ifname=wlan0 (this specifies the interface name according to the instructions packaged in the driver), but the error message still keeps coming up. Is there something else I need to do in Linux to configure the wlan0 part or is the module not recognizing the wireless network card? It would be quite strange if it is the later since all information from the Internet is indicating this is the linux driver I should be using for mentioned wireless card.

  Read the article

• Disable (or switch off) a network interface on windows but keep the "plug and play"

  - by Leandro

  I'm looking for a good workaround to do this on Windows 7 and Windows XP: Disable or make ineffective the network interface (ETH, WIFI, any NIC). If the user connect his ETH cable, the network interface enable again. Important Notes to take care: I'm working with wmic on Win7 (through the command line) I'm working with devcon on WinXP (through the command line) I'm specifically working with the .NET Framework 2.0 on C# but this is just for informational purposes. I know that an event won't help me to detect it (if there is a way or workaround to do this I don't know it). The real problem is that when I disable the NIC, I can't know if the user connects his cable or has a wired network. This is why I am looking for a workaround. I'll treat suggestions as answers if no direct answer exists. I'll provide any extra detail necessary.

  Read the article

• Static IPv4 and dynamic IPv6 on same interface

  - by Zsub

  I am trying to set up a CentOS 5.4 box to use a static IPv4 address, while getting a dynamic IPv6 address at boot time. I have only one interface, apart from the loopback interface, eth0. It has a static v4 and internet connectivity (I can SSH in). However, it doesn't get an IPv6 by default. I have enabled IPv6 in /etc/sysconfig/network and I have added IPV6INIT=yes to the config in /etc/sysconfig/networking/devices/. If I use dhcp6c it does get a valid IPv6 address, but the main question is how do I configure it to get one at boot-time?

  Read the article

• second ip address on the same interface but on a different subnet

  - by fptstl

  Is it possible in CentOS 5.7 64bit to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet? Here is the original config for eth0 more etc/sysconfig/network-scripts/ifcfg-eth0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.91.255 HWADDR=00:1D:09:FE:DA:04 IPADDR=192.168.91.250 NETMASK=255.255.255.0 NETWORK=192.168.91.0 ONBOOT=yes And here is the config for eth0:0 more etc/sysconfig/network-scripts/ifcfg-eth0:0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0:0 BOOTPROTO=static BROADCAST=10.10.191.255 DNS1=10.10.15.161 DNS2=10.10.18.36 GATEWAY=10.10.191.254 HWADDR=00:1D:09:FE:DA:04 IPADDR=10.10.191.210 NETMASK=255.255.255.0 NETWORK=10.39.191.0 ONPARENT=yes How would the resolv.conf file should change since there are two different gateways? Any other change needed?

  Read the article

• Single-port 2600 router with 2900XL switch

  - by Slava Maslennikov

  I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

  Read the article

• Filesystem access through web interface

  - by Jorge Suárez de Lis

  I have an SSH+Samba server so people can access its files from anywhere on the network. I thought it would be also interesting to provide access through a web interface, so they can access the files even when they don't have access to the VPN or a Samba/SSH client. Something like the Ubuntu One or Dropbox web interface. The http server could be on the same machine as the SSH+Samba, so it should just provide access to local files and some way to login with their username/password. Someone knows any software like this?

  Read the article

• Rhino Mocks - Fluent Mocking - Expect.Call question

  - by Ben Cawley

  Hi, I'm trying to use the fluent mocking style of Rhino.Mocks and have the following code that works on a mock IDictionary object called 'factories': With.Mocks(_Repository).Expecting(() => { Expect.Call(() => factories.ContainsKey(Arg<String>.Is.Anything)); LastCall.Return(false); Expect.Call(() => factories.Add(Arg<String>.Is.Anything, Arg<Object>.Is.Anything)); }).Verify(() => { _Service = new ObjectRequestService(factories); _Service.RegisterObjectFactory(Valid_Factory_Key, factory); }); Now, the only way I have been able to set the return value of the ContainsKey call is to use LastCall.Return(true) on the following line. I'm sure I'm mixing styles here as Expect.Call() has a .Return(Expect.Action) method but I can't figure out how I am suppose to use it correctly to return a boolean value? Can anyone help out? Hope the question is clear enough - let me know if anyone needs more info! Cheers, Ben

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >