Search Results

Search found 19486 results on 780 pages for 'link submission'.

Page 35/780 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• Link rate between EMC DAE and HBA

  - by Johan Christensson

  I have a EMC DAE (KTN-STL4) drive cage directly connecconnected to a HP Proliant server using a QLogic QLE2560 HBA. I'm using copper cable between the HBA card and the DAE. On the controller card in the DAE there is a label that states "4Gb". I'm guessing that this means 4Gbit/s. But if I set the HBA card to "Auto speed" it negotiate 2Gbit/s, and if I hard set it to 4Gbit/s I end up with no link. Why is this? Isn't the DAE controller card capebel of link speed higher then 2Gbit/s or is it the copper cable that limits the speed, or is it the interface used between the DAE and Qlogic HBA that is the problem? I have been browsing for HSSDC-FC converters and they always seems to på rated at ~2Gbit/s. If this is the limit, why does it say 4Gb on the controller cards in the DAE?

  Read the article

• linksys Rvo16 redundant link config

  - by Adeodatus

  Hi All I have been given an RVO16 to play with. I'm multihomed and I'd like to set it up so that my primary, highest bandwidth link receives all traffic and the other connection is a hot spare basically. I want them both online but only the primary 1 used until it goes down then all traffic should automatically failover to the secondary link. Those of you that have played on an RVO16, can I do this and if so, how? I imagine I'd have it act as a router and pad the route on one so that the other is never used unless the primary is down. How? Thanks all.

  Read the article

• TP-LINK TD-W8151N Modem/router as just wi-fi router

  - by Reshma

  I am planning to buy TP-LINK ADSL wifi router (model TD-W8151N) for my Internet connection which provides Internet through ADSL telephone line. I am also planning to take cable internet in a few months which provides internet through a LAN cable without the need of any modem. So I would like to have my modem work for both connections which I am using. When using cable internet I want this TP-Link modem to work just as a wireless router (so that I can have the freedom to use my laptop in different rooms instead of sitting at a place by plugging in that cable). Is it possible to use this modem in that way? I don't have much knowledge about these things except that I can configure things as instructed. Please suggest me whether I should go ahead and buy this one or if there is any other modem in your view which can serve both my purposes, let me know. Operating System I am using: Windows 7

  Read the article

• "Fast link detected" warning in GP management console

  - by ???????? ??????

  There is a message that is shown in every report i make in Group Policy Results section of Group Policy Management Console, saying that "A fast link is detected". I followed the link in the waring, but after I read the page several times, I concluded, that I can ignore the warning. However, I noticed that the group policies are not applied when security filtering is used untl "gpupdate /sync" is executed... Is this related to the fast sync? In general, can somebody explain me the consequences of fast links briefly?

  Read the article

• Setting up Linux VPN Client on Mint: Never sends "Set-Link-Info" packet

  - by cabanaboy

  I have tried to set up a VPN Connection on the Linux Mint disto, but could not get it working. When I use a Windows 7 VPN client it works fine. I brought up Wireshark on both Windows and Linux machine and noticed that on the Windows machine, the client never attempted to send the "Set-Link-Info" packet whereas the Windows (working) VPN client did. Why isn't the Linux Mint client sending the "Set-Link-Info" packet. I think if it did that, then my connection would work. What am I missing?

  Read the article

• Apache won't start after creating symbolic link

  - by Carlin

  I'm installing apache for the first time and trying to display some webpages on localhost. Apache's default path for serving web pages is /var/www/html/ but I don't have permissions to write there. Rather than change ownership of the entire directory, I decided to get rid of the /html/ folder in /var/www/ and created it in my home directory. Then I made a symbolic link ln -s /home/me/html/ /var/www/ hoping Apache would serve web pages from my home directory while keeping the default path and following the symbolic link to my home directory. When I go to start the apache service with service httpd start I get Job failed. See system journal and 'systemctl status' for details.

  Read the article

• Creating a Network link between 2 buildings

  - by Adam

  Hey My company needs to create a network link between two buildings. Currently we have a cat5e network in one building and would like to connect some computers(about 15) in our second building to the main network in the first building. The distance between the two buildings is 30 metres. The 30 metres means going through a wall from the first building. Going through the car park and then through a wall into the other building. We can run any cables through speed ramps and so we do not need to dig up the road! Also the second building does not have an Internet connection and so we have to create some sort of cable link so that they can share our Internet connection. Ideas? Should we just run cat5e? Should we run fibre? Should we run coaxial?

  Read the article

• Using the link command to keep backups on another drive

  - by Xavier

  I have a folder that contains a not so large amount of space called /data/backup. I have been told that if I link that folder (/data/backup) to an even bigger folder area like /bigdata/backup for example, that I will be able to execute backups to the /data/backup folder. It will then just create a link, but the data will be seen in both folders and the latter one (/bigdata/backup) will contain the backup results but it will show on both folders. Since the /bigdata/backup has far more disk space then the backup will no longer fail because of space problems in the /data/backup one. Is this true?

  Read the article

• Running a bash script from an HTML link or button

  - by Andrew

  I have a webserver that's hosting lots of images. I want the client to be able to press a button or a link, which will run a bash script, which will create a video based on all these pictures. The script I'm trying to run is this: #!/bin/bash # cd to the directory cd /var/www/gallery # use ffmpeg to make video ffmpeg -pattern_type glob -i 'img-*jpg' -r 1 video.mp4 # Take the first file in the directory and name it video.mp4.jpg (for thumbnail) cp `ls | sort -n | head -1` video.mp4.jpg The script is located on the server. So when the client clicks the link or button, the script will run, and the video is created. I've tried both solutions listed here but I can't seem to get it to work. I have php installed on my server.

  Read the article

• Everytime I click on a link from within Mac, parallels boots up my Windows VM and opens the link there

  - by Christoph

  Everytime I click on a link from within Mac, parallels boots up my Windows VM and opens the link there. That's super annoying and I haven't found a configuration to change it. In the settings of my Windows VM there is an option where to launch the webbrowser. However that seems to only affect links that I open from within my Windows session. UPDATE I just stumbled across this answer: How to disassociate a file type with an application in Mac OS So I disabled "share windows apps with mac" completely. Also this seems to be overly protective it at least does the trick. I think it also deactivates that running windows apps show up in the dock but I don't care that much about that anyway.

  Read the article

• Break a hard link of a file in use

  - by Stebi

  I used hard links to merge duplicated files on my SSD (space is still precious) and now have a weird problem. Common files like msvcr110.dll got hard linked. Now I want to delete a program which has this file in its installation directory. But I cannot because this file (on another location) is used by a currently running application (don't know which) and windows doesn't allow me to delete this file because it's in use. I can rename the file but it still points to the same file, so not possible to delete it. Is there any way to break a the hard link of a file which is currently in use? I currently use a trash folder where I move those files to so I can delete the directory structure of program to be deleted. But I'd like to get rid of this leftover (although it doesn't take much space as it's a hard link).

  Read the article

• Creating a network link between 2 very close buildings

  - by Daniel Johnson

  I have a charity who have two adjacent medium sized modern detached houses (in the UK): the buildings stand next to each other and are less than 5 metres apart. They have DSL connected to a single computer in one of the buildings. They want to add a network with wireless, and want it to work across both buildings. Being a charity they need to keep costs down. The network would be used for sharing Word documents, e-mail, browsing and skyping. My initial thoughts were to connect the buildings with fibre. So: Option 1 Use fibre between the buildings. Sufficient cable and two TP-LINK MC100CM Fast Ethernet Media Converters. Cost ~£80.00. But there is the extra cost and hassle of running the cable down and up the external walls, lifting and relaying paving, and burying underground. Never having fitted fibre I'm also a little worried about going up the wall and then bending the cable at 90 degrees to go through the wall and into the building. Option 2 Use two TP-Link TL-WA7510N High Powered Outdoor 5Ghz 15dBi Wireless antennas to connect the buildings. There is a clear line of sight at first floor level. Cost ~£100. And much easier to fit than fibre! Is using the TL-WA7510Ns overkill? Is there something more suitable? I had hoped to use some Netgear stuff, e.g. two DGN2200, one in each house and also use them to provide the wireless link between the buildings. However, in bridge mode wireless client association is not available and repeater mode with client association only supports WEP security which isn't strong enough. Is there something similar that would be up to the job? Option 3 Connect the buildings with UTP cable. My concerns here are risk of electric shock due to a difference of potential between the buildings (or are they so close this shouldn't be an issue) and protection from lightning strikes. Is fitting lighting arrestors expensive? And what can be done to ameliorate against the risk of shock? This all falls outside my area of expertise so I would really appreciate some advice.

  Read the article

• How to access original files from before a symlink gets updated, which have since been moved to another dir

  - by Luke Cousins

  We have a website and our deployment process goes somewhat like the following (with lots of irrelevant steps excluded) echo "Remove previous, if it exists, we don't need that anymore" rm -rf /home/[XXX]/php_code/previous echo "Create the current dir if it doesn't exist (just in case this is the first deploy to this server)" mkdir -p /home/[XXX]/php_code/current echo "Create the var_www dir if it doesn't exist (just in case this is the first deploy to this server)" mkdir -p /home/[XXX]/var_www echo "Copy current to previous so we can use temporarily" cp -R /home/[XXX]/php_code/current/* /home/[XXX]/php_code/previous/ echo "Atomically swap the symbolic link to use previous instead of current" ln -s /home/[XXX]/php_code/previous /home/[XXX]/var_www/live_tmp && mv -Tf /home/[XXX]/var_www/live_tmp /home/[XXX]/var_www/live # Rsync latest code into the current dir, code not shown here echo "Atomically swap the symbolic link to use current instead of previous" ln -s /home/[XXX]/php_code/current /home/[XXX]/var_www/live_tmp && mv -Tf /home/[XXX]/var_www/live_tmp /home/[XXX]/var_www/live The problem we are having and would like help with is that, the first thing any website page load does is work out the base dir of the application and define it as a constant (we use PHP). If then during that page load a deployment occurs, the system tries to include() a file using the original full path and will get the new version of that file. We need it to get the old one from the old dir which has now moved as in: System starts page load and determines SYSTEM_ROOT_PATH constant to be /home/[XXX]/var_www/live or by using PHP's realpath() it could be /home/[XXX]/php_code/current. Symlink for /home/[XXX]/var_www/live get updated to point to /home/[XXX]/php_code/previous instead of /home/[XXX]/php_code/current where it did originally. System tries to load /home/[XXX]/var_www/live/something.php and gets /home/[XXX]/php_code/current/something.php instead of /home/[XXX]/php_code/previous/something.php I'm sorry if that is not explained very well. I'd really appreciate some ideas on how to get around this problem if someone can. Thank you.

  Read the article

• Linux using the link command

  - by Xavier

  Here it goes. I have a folder that contains a not so large amount of space called /data/backup but I have been told that if I link that folder (/data/backup) to an even bigger folder area like /bigdata/backup for example, that I will be able to execute backups to the /data/backup folder because it will be just a link but the data will be seen in both folders and the latter one (/bigdata/backup) will contain the backup results but it will show on both folders and since the /bigdata/backup has far more disk space then the backup will no longer fail because of space problems in the /data/backup one. Is this true? Thanks Xav

  Read the article

• How to use a D-Link usb network adapter on debian

  - by Barranka

  I have a Debian (squeeze) desktop, and I need to use a D-Link 150 USB Wireless Network Adapter. So far I've done this: $ lsusb ... Bus 001 Device 006: ID 2001:3c18 D-Link Corp. ... After looking for a solution in google, I found that I needed to install the following package: firmware-ralink_0.28+squeeze1_all.deb I've installed it, but Debian doesn't want to find the adapter. When I run lsmod, I can't find what I'm supposed to find: rt2870sta Can you point me in the right direction?

  Read the article

• rsync --link-dest behaviour when run as sudo

  - by fotNelton

  In order to create regular backups, I'm using rsync together with --link-dest so as to create hard-links for unchanged files. For example: rsync -ax \ --partial --delete --delete-excluded --inplace \ --exclude-from=/tmp/temp_excludes \ --link-dest=/Volumes/Backup/current \ /Users /Volumes/Backup/2012-06-25 This works very well as long as I start the process from my normal user account. Though as soon as I start the process using sudo it behaves erradically, meaning that rsync copies all the unchanged files instead of hard-linking them. Since sudo modifies the environment, I've already also tried sudo -E in conjunction with making sure that my sudoers file has the corresponding option set. Well, that didn't work either. So, the question is, how can I run rsync using sudo? Whereas the above example only shows a backup of the Users directory, I also need to backup some system files that I can only access as root.

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• D-link Local wireless

  - by Filippo

  I created a wireless network inside a D-Link DIR-301 connected to a Mac, What I want is that every device to connect to this network if the browser automatically opens instead of the default homepage, it redirects to my website already set in the localhost of the machine which also has the router attached. I'd also like to see that instead of the IP to connect to the site, there will be a "fake" link. What do you advise me? how can I proceed? I state that I am a bit novice in this field, being more a web programmer.

  Read the article

• .htaccess - Simulating virtual host wrong link to Parent Directory in Directory Listing

  - by ?????? ?????

  I have a domain dedicated for my local server (.dev), and an .htaccess file which redirects requests like http://folder.dev/subfolder/ to /htdocs/folder/subfolder. It works great and all, except for one minor issue. When I have the Directory Listing enabled, I can access all the folders, subfolders and files properly, except when I click on the Parent Directory link, which, for example, should lead to http://folder.dev, but redirects to http://folder.dev/folder/ and consequently throws 404 not found. Similarly, if Parent Directory should link to http://folder.dev/subfolder/, it links to http://folder.dev/folder/subfolder/. Here's how my .htaccess looks like: RewriteEngine On RewriteBase / RewriteCond %{REQUEST_URI} !(/$|\.) RewriteRule (.*) %{REQUEST_URI}/ [R=301,L] RewriteCond %{ENV:REDIRECT_SUBDOMAIN} ="" RewriteCond %{HTTP_HOST} ^(www\.)?([a-z0-9][-a-z0-9]+)\.dev\.?(:80)?$ [NC] RewriteCond %2 !^www|ftp|mail|pop3|localhost$ RewriteCond %{DOCUMENT_ROOT}/%2 -d RewriteRule ^(.*) %2/$1 [E=SUBDOMAIN:%2,L] RewriteRule ^ - [E=SUBDOMAIN:%{ENV:REDIRECT_SUBDOMAIN}] Apart from that one thing, everything else works fine (e.g. relative links in documents etc.)

  Read the article

• Why "scope link" ipv6 address can be pinged via interfaces which they are not active on

  - by olagu

  [root@2_01 ~]# /sbin/ip -6 addr show pubeth0 inet6 2001:1::6/64 scope global inet6 2001:1::1/64 scope global inet6 fe80::20c:29ff:fe69:f9e8/64 scope link [root@v2_01 ~]# /sbin/ip -6 addr show pubeth1 inet6 fe80::20c:29ff:fe69:f906/64 scope link [root@2_01 ~]# ping6 fe80::20c:29ff:fe69:f9e8%pubeth1 PING fe80::20c:29ff:fe69:f9e8%pubeth1(fe80::20c:29ff:fe69:f9e8) 56 data bytes 64 bytes from fe80::20c:29ff:fe69:f9e8: icmp_seq=1 ttl=64 time=0.259 ms --- fe80::20c:29ff:fe69:f9e8%pubeth1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 286ms rtt min/avg/max/mdev = 0.259/0.259/0.259/0.000 ms [root@2_01 ~]# ping6 fe80::20c:29ff:fe69:f9e8%pubeth0 PING fe80::20c:29ff:fe69:f9e8%pubeth0(fe80::20c:29ff:fe69:f9e8) 56 data bytes 64 bytes from fe80::20c:29ff:fe69:f9e8: icmp_seq=1 ttl=64 time=0.057 ms --- fe80::20c:29ff:fe69:f9e8%pubeth0 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 390ms rtt min/avg/max/mdev = 0.057/0.057/0.057/0.000 ms Why can I ping6 "fe80::20c:29ff:fe69:f9e8" via pubeth1?

  Read the article

• Clicking on a link in Chrome opens up Notepad

  - by jonsca

  I'm currently using Chrome 21.0.1180.89 on Windows 7, but I have noticed this behavior in other versions before. Probably about one time in a hundred, I will click on a link on a website and an instance of Notepad will open up with a blank page rather than the browser going to the link. To my knowledge, I have no malware or viruses on the machine that could be causing this. It's a minor annoyance, so I'm not very concerned about it, but I'm wondering if there could be a MIME type that's set wrong by default in the browser?

  Read the article

• Can't access link in network using fully qualified domain name

  - by user1033715

  I have installed windows server 2003 and configured Domain controller (domain name - xyz.com) and DNS service. for that I have configured fully qualified domain name as server.xyz.com also I have installed apache tomcat with port 8080 on that server and accessed link successfully using "http://localhost:8080", "http://ip address of server:8080", "http://server.xyz.com:8080". but its working for local machine, and when I tried to access it from another machine in same network using "http://ip address of server:8080" its worked for me. but when I tried it using fully qualified domain name i.e. "http://server.xyz.com:8080" it's giving me error, "Could not connect to server.xyz.com" Please guide me getting this setup done. I need to be able to access this link "http://ip address of server:8080" as "http://server.xyz.com:8080" outside my network Any suggestion are highly appreciated..

  Read the article

• iphone - direct link to iPhone review form from inside iphone

  - by Mike

  I am trying to link directly to the review link of one of my Apps. I know that it is possible because Appirater did it in the past, but some change in iTunes turned the API down. Appirater uses this URL NSString *templateReviewURL = @"itms-apps://itunes.apple.com/WebObjects/MZStore.woa/wa/viewContentsUserReviews?id=APP_ID&onlyLatestVersion=true&pageNumber=0&sortOrdering=1&type=Purple+Software"; where APP_ID is the ID of an application. running this from inside the APP gives me the message Cannot Connect to iTunes Store. This Page talks about another kind of link https://userpub.itunes.apple.com/WebObjects/MZUserPublishing.woa/wa/addUserReview?id=APP_ID&type=Purple+Software and also itms-apps://ax.itunes.apple.com/WebObjects/MZStore.woa/wa/viewContentsUserReviews?type=Purple+Software&id=APP_ID The first one works, but just from the desktop mac. The second gives me the same error as the first... Cannot Connect to iTunes Store. iTunes link maker is not helping too, because it has no tools for iPad links... Do you guys know how to link to an app's review form from inside an app? In case you don't know, what kind of package should I use to dig this? a package sniffer? thanks for any help.

  Read the article

• Extremely strange iTunesConnect error--Missing Screenshot??

  - by Steve

  So I finally got through the mess of preparing my app binary to support the iPad, making it a univeral app, and then I got this strange error "Missing Screenshot". And due to the fact that I hadn't uploaded my iPad screenshots to the original binary (I forgot) that error made sense. So I went into the original iPhone app, added my iPad screenshots, and hoped that somehow it would just work, but it didn't. So then, I rejected the binary, and made sure the iPad screenshots were where they needed to be, re-uploaded a new binary, and it still says MISSING SCREENSHOT. I emailed apple, and they characteristically won't get back to me till probably sometime next week, so I am hoping that someone here can shed some on this error for me! What can I do to get that error to go away, so I can get my ap reviewed and updated? Thank you very much!

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >