Search Results

Search found 10313 results on 413 pages for 'hardware sharing'.

Page 352/413 | < Previous Page | 348 349 350 351 352 353 354 355 356 357 358 359  | Next Page >

• Why does ATI 5570 HD video card driver installation cause Windows 7 To Blue Screen?

  - by Mort

  This one is for the hive mind. I have a brand new Dell Optiplex 760 workstation with 4 gigabytes of RAM running Windows 7 Professional (32bit). This is a new box with nothing installed other than what was provided for directly by Dell. I installed a Saphire ATI PCI Express 5570 HD. Upon trying to install the 10.4 Catalyst drivers the system will blue screen. It blue screens during the hardware detection phase of the installation process. I have already performed the following trouble shooting steps: Changed system RAM Installed only 2 gigabytes of RAM Installed different versions of Catalyst drivers (10.4 - 9.12) Tried to install video only component of driver (vs entire Catalyst suite) Made sure Windows 7 was fully updated Flashed mother board BIOS to current version Removed and re-seated video card Contacted ATI Support (We all know how this went......) Verified supply outputting properly The blue screen error (via Windows BugCheck entry in event log) is a 0x000000CA and refers to a plug and play error most likely caused by a bad driver. The problem is that the driver installation process never gets far enough to actually install a driver. The resolution center in Windows provides a solution of installing the 10.4 Catalyst driver to resolve issue (which fails). Looking for some alternate views to resolve.

  Read the article

• Most transparent way to connect two LANS using a WET610N Wireless Bridge

  - by Spencer Ruport

  I have two wired systems hooked to a Linksys WRT54GL wired/wireless router which is also hooked to my internet. I'll refer to this as LAN1. I have two more systems in another room that are connected wirelessly. Recently I decided I would much rather have another wired LAN in the other room and use a bridge to connect them. This would be LAN2. Prior to hooking up the device I assumed that the ethernet side of the bridge would have a DHCP server so that I could simply hook it up to a switch and I'd be on my way. However that isn't the case which leads me to believe I'll have to add one to LAN2 correct? Or is there some way to have the DHCP from LAN1 also hand out IP addresses to LAN2? If I do need a DHCP device on LAN2 what would be best? Another hardware device or should I just install some DHCP software on one of the systems (since they're both on 24/7 anyway). Any recommendations would be appreciated. :)

  Read the article

• Mac Management Without Permission and Security

  - by Bart Silverstrim

  I was going through some literature on managing OS X laptops and asked someone some questions about usage scenarios when using the MacBooks. I asked someone more knowledgeable than I about whether it was possible for my Mac to be taken over if I were visiting another site for a conference or if I went on a wifi network at a local coffee house with policies from an OS X Server with workgroup manager (either legit for the site or someone running a version of OS X Server on hardware they have hidden somewhere on the network), which apparently could be set up to do things like limit my access to Finder or impose other neat whiz-bang management features. He said that it is indeed possible for it to happen as it would be assigned via the DHCP server and the OS X server would assume my Mac is a guest and could hand out restrictions and apparently my Mac will happily accept them without notifying me or giving me an option, unlike Windows which I believe would need to be joined to a domain before it becomes "managed" by Active Directory. So my question is as network admins and sysadmins with users traveling with MacBooks, is there a way to reasonably protect your users from having their machines hijacked without resorting to just turning off networking all the time? Or isn't this much of a security hazard? What threat does this pose to the road warriors in your businesses?

  Read the article

• Remote server security: handling compiler tools

  - by Gonzolas

  Hello! I was wondering wether to remove compiler tools (gcc, make, ...) from a remote production server, mainly for security purposes. Background: The server runs a web application on Linux. Consider Apache jailed. Otherwise, only OpenSSHd faces the public network. Of course there is no compiler stuff within the jail, so this is about the actual OS outside of any jails. Here's my personal PRO/CON list (regarding removal) so far: PRO: I had been reading some suggestions to remove compiler tools in order inhibit custom building of trojans etc. from within the host if an attacker attains unpriviliged user permissions. CON: I can't live without Perl/Python and a trojan/whatever could be written in a scripting language like that, anyway, so why bother about removing gcc et al. at all. There is a need to build new Linux kernels as well as some security tools from source directly on the server, because the server runs in 64-bits mode and (to my understanding) I can't (cross-)compile locally/elsewhere due to lack of another 64-bits hardware system. OK, so here are my questions for you: (a) Is my PRO/CON assessment correct? (b) Do you know of other PROs / CONs to removing all compiler tools? Do they weigh in more? (c) Which binaries should I consider dangerous if the given PRO statement holds? Only gcc, or also make, or what else? Should I remove the enitre software packages them come with? (d) Is it OK to just move those binaries to a root-only accessible directory when they are not needed? Or is there a gain in security if I "scp them in" every time? Thank you!

  Read the article

• Failed to start apache Can't open /etc/apache2/envvars

  - by bumperbox

  i have had this problem a couple of times now and i am not sure what is causing it Failed to start apache : .: 45: Can't open /etc/apache2/envvars when i look at a dir listing, i get these question marks next to envvars, does anyone know what that means? os is ubuntu 10 if that helps drwxr-xr-x 7 root root 4096 Jan 29 11:56 . drwxr-xr-x 83 root root 4096 Feb 4 10:34 .. -rw-r--r-- 1 root root 8113 Sep 29 01:52 apache2.conf -rw-r--r-- 1 root root 8027 Oct 3 22:26 apache2.conf.dpkg-old drwxr-xr-x 2 root root 4096 Jan 29 11:56 conf.d ?????????? ? ? ? ? ? envvars -rw-r--r-- 1 root root 0 Oct 3 22:25 httpd.conf ?????????? ? ? ? ? ? magic drwxr-xr-x 2 root root 4096 Jan 29 11:56 mods-available drwxr-xr-x 2 root root 4096 Jan 29 10:18 mods-enabled ?????????? ? ? ? ? ? ports.conf drwxr-xr-x 2 root root 4096 Jan 29 11:56 sites-available drwxr-xr-x 2 root root 4096 Jan 29 11:55 sites-enabled UPDATE Just heard back from the hosting company, they move my VPS to a new hardware node last night, and something at their end wasn't quite right which caused the issue

  Read the article

• What parts should I get for an ASRock x58 Extreme motherboard

  - by Brad Gilbert

  I just received an ASRock x58 Extreme motherboard, for my post on this question. It was a 2009 Tom's Hardware recommended buy. It is a Core i7 motherboard, with an X58 Express Chipset. It uses DDR3 RAM. What I want to know is, what parts should I get to finish it off. I'm looking for some good bargains, because of a lack of funds. The most taxing game I will probably play on it is OpenTTD. The only parts I currently have that are compatible: A Dynex 400W power supply. It appears to be an ATX 2.1 power supply, with the addition of a -5 rail. Apparently designed to be compatible with most ATX-style motherboards. Several PCI add-in cards. Mostly 10/100 Network cards Some sound cards Some video cards with a VGA connector Plenty of PATA drives. 8 GB - 80 GB Hard-drives A dozen or-so CD-ROM drives, only a handful of them are CD-RW drives. One DVD-ROM drive I have one LCD, with a 15 pin VGA connector, which I salvaged from the dump. The only thing wrong with it was some dead capacitors. It also has a stuck pixel.

  Read the article

• How to whitelist external access to an internal webserver via Cisco ACLs?

  - by Josh

  This is our company's internet gateway router. This is what I want to accomplish on our Cisco 2691 router: All employees need to be able to have unrestricted access to the internet (I've blocked facebook with an ACL, but other than that, full access) There is an internal webserver that should be accessible from any internal IP address, but only a select few external IP addresses. Basically, I want to whitelist access from outside the network. I don't have a hardware firewall appliance. Until now, the webserver has not needed to be accessible externally... or in any case, the occasional VPN has sufficed when needed. As such, the following config has been sufficient: access-list 106 deny ip 66.220.144.0 0.0.7.255 any access-list 106 deny ip ... (so on for the Facebook blocking) access-list 106 permit ip any any ! interface FastEthernet0/0 ip address x.x.x.x 255.255.255.248 ip access-group 106 in ip nat outside fa0/0 is the interface with the public IP However, when I add... ip nat inside source static tcp 192.168.0.52 80 x.x.x.x 80 extendable ...in order to forward web traffic to the webserver, that just opens it up entirely. That much makes sense to me. This is where I get stumped though. If I add a line to the ACL to explicitly permit (whitelist) an IP range... something like this: access-list 106 permit tcp x.x.x.x 0.0.255.255 192.168.0.52 0.0.0.0 eq 80 ... how do I then block other external access to the webserver while still maintaining unrestricted internet access for internal employees? I tried removing the access-list 106 permit ip any any. That ended up being a very short-lived config :) Would something like access-list 106 permit ip 192.168.0.0 0.0.0.255 any on an "outside-inbound" work?

  Read the article

• How can i get more low memory with the following setup:

  - by user539484

  Modules using memory below 1 MB: Name Total = Conventional + Upper Memory -------- ---------------- ---------------- ---------------- MSDOS 14 317 (14K) 14 317 (14K) 0 (0K) HIMEM 1 120 (1K) 1 120 (1K) 0 (0K) EMM386 3 120 (3K) 3 120 (3K) 0 (0K) OAKCDROM 36 064 (35K) 36 064 (35K) 0 (0K) POWER 80 (0K) 80 (0K) 0 (0K) NLSFUNC 2 784 (3K) 2 784 (3K) 0 (0K) COMMAND 2 928 (3K) 2 928 (3K) 0 (0K) MSCDEX 15 712 (15K) 15 712 (15K) 0 (0K) SMARTDRV 30 384 (30K) 13 984 (14K) 16 400 (16K) KEYB 6 752 (7K) 6 752 (7K) 0 (0K) MOUSE 17 296 (17K) 17 296 (17K) 0 (0K) DISPLAY 8 336 (8K) 0 (0K) 8 336 (8K) SETVER 512 (1K) 0 (0K) 512 (1K) DOSKEY 4 144 (4K) 0 (0K) 4 144 (4K) POWER 4 672 (5K) 0 (0K) 4 672 (5K) Free 552 944 (540K) 539 088 (526K) 13 856 (14K) Memory Summary: Type of Memory Total = Used + Free ---------------- ---------- ---------- ---------- Conventional 653 312 114 224 539 088 Upper 47 920 34 064 13 856 Reserved 0 0 0 Extended (XMS)* 64 898 256 2 671 824 62 226 432 ---------------- ---------- ---------- ---------- Total memory 65 599 488 2 820 112 62 779 376 Total under 1 MB 701 232 148 288 552 944 Total Expanded (EMS) 33 947 648 (33 152K Free Expanded (EMS)* 33 538 048 (32 752K * EMM386 is using XMS memory to simulate EMS memory as needed. Free EMS memory may change as free XMS memory changes. Largest executable program size 538 976 (526K) Largest free upper memory block 7 488 (7K) MS-DOS is resident in the high memory area. I'm running MS-DOS 6.22 on VMWare virtual hardware. This is memory state after memmaker pass, so i'm looking for optimization beyond memmaker. Note: NLS drivers (DISPLAY, KEYB, NSLFUNC) are essential for me. Thanks to @mtone for valuable reminder about MSCDEX /E which gave me 16KiB of low memory (see the diff)!

  Read the article

• Redundant Microsoft server solution for small company

  - by MadBoy

  I'm planning to change one server Microsoft SBS 2003 with SharePoint, Exchange and SQL database into something that will provide me with some redundancy and won't be single point of failure. I was thinking to buy 2x exactly the same physical servers and put 2 virtualized servers on HyperV or VMWare on each. Then i would put SharePoint, Exchange and SQL on that 1 physical server (shared onto 2x VM's). I would like 2nd physical server to be exact duplicate of the first one so that when 1st server goes down (for reboot or hw failure), 2nd takes care of everything so that users don't even see anything changed (in terms all their emails, sharepoint stuff is available). My questions are: Will I have to pay for licenses for both servers even thou only one instance of SharePoint, Exchange, SQL will be used at same time? What are proposed solutions to do that? Any additional hardware I would need, any complicated software configuration to be expected to configure such redundancy so that when one physical server goes down 2nd one is taking care of rest? What problems should I expect? This solution is for 60 people. Later on it may or may expand.

  Read the article

• Handheld Linux device can't see one wireless network

  - by Nathan

  I'm using a Nokia N810 running OS 2008 (version 5.2008.43-7; should be the latest). It can see networks up and down the street in my neighborhood and can connect to mine using WEP. I can also connect to free networks at restaurants and the like. When I bring it into work, it can't see a wireless network ("No connections available"). When I use netstumbler on my laptop I can see a list of several essids showing green connectivity for the network. I know that the network has its essid broadcast, and I know that it's unsecured. When I run iwlist wlan0 scan, I see several APs with no essid, but I don't see anything with an essid set. I have verified using iwlist that my hardware supports the correct channels and speeds. I know this isn't a Nokia/mobile forum, but it's running what's basically a Debian kernel. Any suggestions on what to do in this case? I'm really frustrated by this. Thanks, Nathan

  Read the article

• Using NginX and Apache alongside for both static and dynamic files

  - by faridv

  Background: I've searched a lot and found these useful threads about using of Apache or NginX for static or dynamic files. But they are old (mostly about 1 or 2 years ago) and I think both webservers, specifically Nginx has had important changes in performance and usage. So I think take another look on these issue cannot be that bad. Nginx (for static files) and Apache (for dynamic content)? nginx better than apache for dynamic content? [closed] Apache or NGINX for PHP? Nginx as reverse proxy to Apache with only dynamic content? My question: I have a PHP web application with lots of dynamic files and lots of static contents (videos, images etc.) and it's currently running on a CentOS 6 server and Apache 2.2 since 2 months ago. In past few days, number of our site visitors have gained so fast and I just thought if this number continues to increase with current ratio, we need to change many things (web server, application, etc.) to prevent failures. Because of hardware limitations that we are facing, I thought that it's best for us to start with web server. Should I start with something else? Should I try to increase performance of my PHP application and forget about web server for now? (even if gonna take a long time!) Because of huge usage of .htaccess files (for redirection, rewrites, etc.), I think it's gonna be painful to migrate to NginX as default web server or maybe only for dynamic files. Does this mean that I can't even use Nginx as reverse proxy? I'm not sure latest stable version of NginX and PHP-FPM have a better performance over my current Apache and my limitations (too many things) won't let me to give it a try. Which one is doing better currently? What will I lose by migrating to Nginx? To make it short, what should I do?

  Read the article

• NAT cause huge External (actually internal) bandwidth usage

  - by user67953

  We have 4 servers running in a data center, with internal IP: 192.168.3.* assigned. A hardware (FORTIGATE) firewall configured NAT, and it will lead the traffic as: external IP: 111.222.333.10 -> 192.168.3.10 www.server1.com 111.222.333.11 -> 192.168.3.11 www.server2.com 111.222.333.12 -> 192.168.3.12 www.server3.com In DNS, we have www.server1.com A 111.222.333.10 Now if I send a lot of data to www.server1.com from www.server2.com, the data will be send through 111.222.333.10 (external IP) and this cause our bandwidth usage huge (expensive!). The work around I have is to add a local host mapping to server2: 192.168.3.10 www.server1.com. That way when send files from server2 to www.server1.com, it will be internal. However, we are having more and more servers, it would be hard to manually add mapping to every server. Just wondering do we have another solution for this? Can we do something in the FORTIGATE firewall? ps. The DNS server being used is public, such as opendns, Google dns etc.

  Read the article

• How can I find out which processes on my computer are accessing the microphone?

  - by Vinayak

  After reading this interesting Lifehacker post and reading the comments on the page, one person was wondering if it would be possible to use the Physical Device Object Names of other hardware such as the microphone to find out the names of processes using that device. I tried the same approach, but so far it only seems to work for the webcam. Is there any other way I could get this to work in Process Explorer? UPDATE: The Lifehacker post was about finding out which Windows process is currently using your webcam. This is how they went about doing it: Start Device Manager (WIN+R → "devmgmt.msc" → OK) Find your webcam among the list of devices (check under Imaging Devices) Open the properties window of the device and switch to the Details tab (Right click → Properties → Details) In the dropdown menu, select Physical Device Object Name and copy the string(Right click → Copy) Download Process Explorer Make sure you have opened Process Explorer in Administrator Mode(File → Show Details for All Processes) Hit CTRL+F and enter the string you copied earlier(it should be something like \Device\000000XX) Hit the Search button and you should see a list of processes using the webcam(if there are any)

  Read the article

• Switch Windows 8 from a hybrid MBR/GPT => GPT only on Macbook Pro Retina

  - by Sid

  I used DiskUtility+Bootcamp Wizard to setup my hard drive for Windows 8 (final MSDN). Somewhere in that process, the Apple tools turned my GPT disk into a hybrid MBR/GPT. All my 4 primary MBR partitions are used up, so when I try turning on Bitlocker in Windows 8, it complains about not finding a System drive. I know on Windows 8 the Bitlocker setup tries to create the 200(?)MB system partition if it's missing. However with all 4 partitions filled I suspect it can't create system drive = it can't find it = throws back an error like "BitLocker Setup could not find a target system drive. You may need to manually prepare your drive for BitLocker". I've already tried disabling hibernation, swap file etc. Now I'm thinking that if I were to get rid of the MBR scheme altogether, perhaps I can be alright within the GPT world without MBR's 4 primary partitions limit. So, how can I get rid of the MBR tables on the hybrid scheme in a manner that still leaves Mac OS and Windows 8 in working conditions? Details: Hardware is the MacbookPro Retina. Primary MBR partitions are consumed as follows: EFI partition HFS+ partition (=encrypted, therefore ="Apple_CoreStorage") HFS+ partition (Recovery partition, contains unencrypted Mac bootloader) NTFS partition (Windows8 all-in-one partition) diskutil list output sid-mbpr:~ sid$ diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *251.0 GB disk0 1: EFI 209.7 MB disk0s1 2: Apple_CoreStorage 160.0 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 4: Microsoft Basic Data Win8 90.1 GB disk0s4 GPT vs MBR addresses sid-mbpr:~ sid$ sudo gptsync /dev/rdisk0 Password: Current GPT partition table: # Start LBA End LBA Type 1 40 409639 EFI System (FAT) 2 409640 312909639 Unknown 3 312909640 314179175 Mac OS X Boot 4 314179584 490233855 Basic Data Current MBR partition table: # A Start LBA End LBA Type 1 1 409639 ee EFI Protective 2 409640 312909639 ac Apple RAID 3 312909640 314179175 ab Mac OS X Boot 4 * 314179584 490233855 07 NTFS/HPFS Status: GPT partition of type 'Unknown' found, will not touch this disk.** **: Ignore this message, the gptsync tool is old and doesn't understand the UUID for "Apple_CoreStorage" / FileVault2 partitions. Since LBA addresses are alright, safe to ignore this message.

  Read the article

• Is it possible to detect nearby Wi-Fi enabled devices, not necessarily on the same network? [closed]

  - by Sky

  first question on StackExchange ever. I hope I got the right board. I'm trying to create a device (either from a standard AP or some other unconventional means) that will be able to detect nearby Wi-Fi enabled devices. For example, if a cellular phone (iPhone for instance) would be carried into the secured area, its MAC address will be logged. A cellular phone is a good example because it's the most common threat that should be detected. Some important points: The detection can be either active or passive, doesn't matter. The detected device might be connected to a different network, or might not be connected to anything at all. I assume most cellular phones are actively probing when not connected, but I'm not sure. It is important to not only identify the breach, but also to identify the device (MAC address). Conventional hardware is only optional. Distance of detection is at least 6 meters (20 feet). Handling one device at a time is good. Speed of detection is important, under 5 seconds is ideal. So my question is, is this even possible? If so, what can I use in order to make this a reality? Thank you for reading!

  Read the article

• Are HDMI to VGA Adapters Really Device-Specific?

  - by allquixotic

  There are a lot of devices on the market right now (especially mobile devices) with a Micro-HDMI or Mini-HDMI port and no VGA or D-Sub output. Most manufacturers of said devices sell a cable that looks something like this: I have yet to find a cable like this that claims to work on a wide array of devices. In general, these cables claim to work with one specific device only. The way these cables work, I think, is that analog VGA signals are sent from the HDMI port on the device. This should work for devices that have special hardware on the motherboard/GPU capable of driving this. Is it the case that these cables have to be custom designed for each device? Or, is it rather that any device which possesses this special "signaling of analog VGA over the HDMI port" can be made to work with a cable that is physically compatible (i.e. the HDMI end plugs into the device and the VGA end accepts a VGA monitor cable)? Note that I am not looking for a product recommendation, just a conceptual clarification on what exactly these devices are doing. Also, a few remarks: The cables like the one depicted here are not digital to analog converters. I know about these: they are expensive, and they are the ONLY solution if your device only outputs a digital signal and is incapable of driving analog VGA over the HDMI port. The cables like the one depicted here are not straight crossover cables from VGA to HDMI, either. The crossover cables are designed to send a digital HDMI signal over the VGA port's wires; that is, the wire protocol is HDMI (digital) but the physical pinout is the same as VGA, even though nothing analog is happening. Once again, this is not the behavior that, I believe, the devices which I'm talking about in this question are doing. The cabling and devices that this question is about transmit the analog VGA data over the HDMI port (the HDMI port is in the device outputting the data, and the VGA side is the monitor/projector).

  Read the article

• Why would my HDD main partition suddenly become hidden?

  - by Luis Oscar

  A few days ago I was using my computer as usual and I turned it off. The next day it wouldn't boot up. It just stayed after the hardware diagnostic window on the intermittent underscore screen. So clearly It wasn't booting up. I tried turning it on and off a couple of times with no avail. Finally I used windows 7 disk and it seemed as if there was no HDD. not even the installation would see the HDD. So i thought it was dead, i bought a new one installed it with windows and used a external case with the old HDD. plug it in and still couldn't see it. I finally downloaded a partition program EASUS or something and my HDD was there listed WITHOUT a system letter. I could however explore it and i set it as Unhidden and it came back to life. I could see it normally. I really just wish someone could explain to me what happened here, was it a virus? does it means the HDD is about to die? How can i prevent this or what should I do now? should i stop using this OLD HDD? Thanks

  Read the article

• BIOS corrupted? How to proceed? Acer Travelmate 290

  - by dtlussier

  I have a older ACER Travelmate 290 (manufactured in 2002 or 2003), which I recently tried to upgrade to Ubuntu 9.10. After doing the upgrade process it appeared as if I had a problem with my x server configuration, as on the first reboot post-install I heard the Ubuntu startup sound, but had a black screen. I thought I would then reboot again to drop down into text-mode to trouble shoot the x configuration problem. However, when I tried rebooting, something went wrong and since then when I start up the machine I get absolutely nothing except the first hardware check (i.e. HDD light flashes, CD/DVD drive spins, etc.). Other than that the screen remains totally black and I have no HDD or processor activity at all. I have tried restarting it a number of time holding down all kinds of key combinations to try and coax it into the BIOS (if possible) with no luck. I have also tried putting in both a live Linux disc and a Windows install disk without any luck. With a disk in the drive it will spin for a few seconds and then stop. All this has lead me to suspect that the BIOS is somehow corrupt (not sure about the right terminology). I have tried putting a new BIOS image and installer program downloaded from ACER on a USB key to see if it will run when I start up the machine, but no luck. I'm not sure if this method of interacting/updating/flashing the BIOS will work outside of Windows/DOS as both OSs are mentioned kind of ambiguously in the documentation. I have also taken the laptop case apart and inspected the various cards and cannot find any obviously burned out components. I'm not sure how to proceed at this point in terms of components to try, or how to try and load a new BIOS image onto the board. Any advice here would be great, especially from those with experience with this particular line of laptops. Thanks!

  Read the article

• Keep-Alive header not sent from Tomcat 5.5 http connector?

  - by Codek

  We're currently using a hardware load balancer, which then goes to Apache and that then goes to Tomcat 5.5 via the AJP connector. We've decided to dump apache for various reasons - In our current system it doesnt provide any advantage. However when I look at the headers sent when we do this, the "Keep-Alive: timeout=15 max=96" header doesnt get sent when you use the tomcat http connector Interestingly, i can find no documentiation on "keepalivetimeout" for tomcat5.5, but i can for tomcat6. But neither can i find evidence that tomcat5.5 doesnt support this setting. here's my connector: <Connector port="8090" maxHttpHeaderSize="8192" maxThreads="400" minSpareThreads="150" maxSpareThreads="300" enableLookups="false" connectionTimeout="2" maxKeepAliveRequests="400" disableUploadTimeout="true" /> So; Is there any way I can specify the keepalive timeout if we use the http connector with tomcat 5.5, and force this header entry to be sent? Just to be clear - the exact header entry i see back from the server is this with apache: Keep-Alive: timeout=2, max=100 But nothing from tomcat/coyote. I've looked at this some more, and I dont think the Keep-Alive header entry really matters. The problem seems to be that keep-alives are simply not supported in tomcat 5.5 http connector? They do seem to work in tomcat6 (+java 6). Thanks, Dan

  Read the article

• Request bursting from web application Load Tests

  - by MaseBase

  I'm migrating our web and database hosting to a new environment on all new machines. I've recently performed a Load Test using WAPT to generate load from multiple distributed clients. The server has plenty of room to handle the traffic load, but I'm seeing an odd pattern of incoming traffic during the load tests. Here is the gist of our setup: Firewall server running MS Forefront TMG 2010 on Win 2k8 server Request routing done by IIS Application Request Routing on firewall machine Web server is a Hyper-V VM on the Database server (which is the host OS) These machines are hefty with dual-CPU's with six cores (12 total procs) Web server running IIS 7.5 Web applications built in ASP.NET 2.0, with 1 ISAPI filter (Url Rewrite) in front What I'm seeing during the load tests is that the requests all come through in bursts. Even though I have 7 different distributed clients sending traffic loads, the requests come through about 300-500 requests at a time. The performance monitor shows nearly all of the counters moving through this pattern, where a burst of requests comes in the req/sec jumps to 70, the queued requests jumps to 500, the current requests jumps up, the CPU jumps up, everything. Then once it's handled that group of requests, it has a lull for nearly 10 seconds where nearly nothing is happening. 0-5 req/sec, 0 queued requests, minimal CPU usage. Then after 10 seconds of inactivity, another burst comes through, spiking all of the counters once again. What I can't figure out is why the requests are coming through in bursts when I know that the load being generated is not sent that way, especially considering the various load-generating clients sending traffic all in different intervals with random think time's between each request. Is there something in the layers between Hyper-V or perhaps in the hardware which might cause this coalesce of requests together? Here is what i'm looking at, the highlighted metric is Requests/sec, but the others critical counter go with it: Requests Queued (which I'd obviously like to keep as close to 0 as possible). Any ideas on this?

  Read the article

• Spurious alleged file corruption on Windows 7

  - by Johannes Rössel

  Recently my Laptop sometimes warns about corrupted files on the hard drive (Samsung SSD PB22-JS3 TM). This has only happened so far when updating (or checking out) an SVN repository with either TortoiseSVN or the command line Subversion client. The fun thing is that the corrupted file has always been a .svn directory (although the directory entry may contain files in that directory too, if they're small enough?—?which should be the case with SVN). However, when looking into the warned-about directory I notice nothing strange or unusual and don't get any more warnings about it and another try (SVN stops updating once that error occurs?—?TortoiseSVN even with an appropriate error message) of updating the working copy works (well, mostly; sometimes it does it again, albeit with a different directory). Since the laptop is only a few months old I doubt the SSD is failing already—five months of normal usage shouldn't be too surprising. Also it (so far) occurred only with SVN updates on a large repository. Maybe that's too many writes in a short time and some part between the software and the hardware doesn't quite catch up fast enough or so?—?I don't know enough about this to actually make an informed guess here. Anyone knows what's up here? ETA: Note to add: I've run chkdsk (it seems to schedule itself anyway when this happens) and it didn't find anything out of the ordinary.

  Read the article

• cisco 2900xl - SNMP - Get mac address of device connected to an interface

  - by ankit

  Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

  Read the article

• Windows 7 Black Screen On Boot, Seperate Bootable VHD Works Fine

  - by David Osborn

  I have a Window 7 x64 install with a bootable VHD (also Windows 7 x64). I was having problems getting my homeserver to do backups (VSS erred) so I ran check disk and used a tool from MS (cleanc2r.exe) to remove an empty Q drive from the VHD that I believe was a result of installing Office 2010 Beta. (All of this was done on the bootable VHD, not the main install.) Now I can't boot into the main install. It gets past the Starting Windows screen and then goes black. I can still boot into the bootable VHD and everything works fine from there. I have tried to boot the main install in Safe Mode/Safe Mode with Networking/and Safe Mode command prompt and it has the same issue. I ran chkdsk /r on the main install and after doing all the work there was a message about correcting some free space that was marked as allocated and also that it was unable to make an entry into the event log. I tried the startup repair utility and it found no problems. I don't see the setting for restore to last know good configuration so I couldn't do that. I don't recall installing anything new to the main install nor having hooked up any new hardware recently.

  Read the article

• Cheapest iSCSI SAN for Windows 2008/SQL Server clustering?

  - by MichaelGG

  Are there any production-quality iSCSI SANs suitable for use with Windows Server 2008/SQL Server for failover clustering? So far, I've only seen Dell's MD3000i, and HP's MSA 2000 (2012i), which both are around $6K with a minimal disk configuration. Buffalo (yea, I know), has a $1000 device with iSCSI support, but they say it will not work for 2008 failover clustering. I'm interested in seeing something suitable for failover in a production environment, but with very low IO requirements. (Clustering, say, a 30GB DB.) As for using software: On Windows, StarWind seems to have a great solution. But it's actually more money than buying a hardware SAN. (As I understand, only the enterprise edition supports having replicas, and that's $3000 a license.) I was thinking I could use Linux, something like DRBD + an iSCSI target would be fine. However, I haven't seen any free or low-cost iSCSI software that supports SCSI-3 persistent reservations, which Windows 2008 needs for failover clustering. I know $6K isn't much at all, just curious to see if there are practical cheaper solutions out there. And finally, yes, the software is expensive, but many small business get MS BizSpark, so the Windows 2008 Enterprise / SQL 2008 licenses are completely free.

  Read the article

• Upgrading memory on an IBM Power 710 Express (8231-E2B)

  - by cairnz

  We have a Power 710 Express server that was loaded with 4x4 GB memory on a single riser card. I have replaced the 4 chips with 4x8GB and put in another riser card and loaded it with 4x8GB more for a total of 64GB memory. The firmware is AL730_078. When i power it on, the service processor boots up and i can access the ASMi. From here I can look at "Memory Serial Presence Data" and see that the system in some way detects 8x8 GB. However when i look at Hardware Deconfiguration and specifically Memory Deconfiguration, it is still listed with old values, 16384MB, and claims there are 4x4 chips in the C17 riser. How do i proceed to make the server recognize properly the amount of memory installed? I get a FSPSP04 and B181B50F progress code on booting because (i think) it hasn't been told the memory has changed. It then does not proceed to booting the operating system (VIOS) when turned on. Are there any steps I have overlooked here? Can I do some commands, either on the service processor, or otherwise, to tell the system to configure with the proper amount of memory? PS: This is a stand alone server, not configured with HMC or SDMC.

  Read the article

< Previous Page | 348 349 350 351 352 353 354 355 356 357 358 359  | Next Page >