Search Results

Search found 10280 results on 412 pages for 'remote shutdown'.

Page 352/412 | < Previous Page | 348 349 350 351 352 353 354 355 356 357 358 359  | Next Page >

• Vlans and subinterfaces

  - by Adeodatus

  I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

  Read the article

• ipmi - can't ping or remotely connect

  - by Fidel

  I've tried configuring the IPMI controller to accept remote connections, but I can't even ping it. Here is it status: #/usr/local/bin/ipmitool lan print 2 Set in Progress : Set Complete Auth Type Support : NONE PASSWORD Auth Type Enable : Callback : : User : NONE PASSWORD : Operator : PASSWORD : Admin : PASSWORD : OEM : IP Address Source : Static Address IP Address : 192.168.1.112 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:67:45:25 IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Enabled Gratituous ARP Intrvl : 8.0 seconds Default Gateway IP : 192.168.1.1 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : Disabled 802.1q VLAN Priority : 0 RMCP+ Cipher Suites : 0,1,2,3 Cipher Suite Priv Max : uaaaXXXXXXXXXXX : X=Cipher Suite Unused : c=CALLBACK : u=USER : o=OPERATOR : a=ADMIN : O=OEM # /usr/local/bin/ipmitool user list 2 ID Name Enabled Callin Link Auth IPMI Msg Channel Priv Limit 1 true false true true USER 2 admin true false true true ADMINISTRATOR # /usr/local/bin/ipmitool channel getaccess 2 2 Maximum User IDs : 5 Enabled User IDs : 2 User ID : 2 User Name : admin Fixed Name : No Access Available : callback Link Authentication : enabled IPMI Messaging : enabled Privilege Level : ADMINISTRATOR # /usr/local/bin/ipmitool channel info 2 Channel 0x2 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : multi-session Active Session Count : 0 Protocol Vendor ID : 7154 Volatile(active) Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available Non-Volatile Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available # /usr/local/bin/ipmitool chassis status System Power : on Power Overload : false Power Interlock : inactive Main Power Fault : false Power Control Fault : false Power Restore Policy : unknown Last Power Event : Chassis Intrusion : inactive Front-Panel Lockout : inactive Drive Fault : false Cooling/Fan Fault : false # arp Address HWtype HWaddress Flags Mask Iface 192.168.1.112 ether 00:A0:A5:67:45:25 C bond0 # /usr/local/bin/ipmitool -I lan -H 192.168.1.112 -U admin -P admin chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status In summary. It exists on the ARP list so arp's are being broadcast. I can't ping it and can't connect to it. Can anyone spot any glaring mistakes in the configuration? Many thanks, Fidel

  Read the article

• SSH client not showing prompt after successful login

  - by user431949

  I'm having problems with my SSH client on Ubuntu 10.10. When I switch on my computer and open a Terminal and execute the command ssh user@host, it gives me a password prompt after which I enter the right password, I then get a prompt to execute my commands on the remote computer. Now the problem is, after a little while (probably around 10 minutes), the terminal window stops accepting commands (No matter what I type, nothing shows). Once this happens, I close the Terminal window and try to start all over again by opening another Terminal window. But this time around, after entering the right password, I don't get a welcome message or prompt. The cursor just keeps blinking on a new line. I ran the ssh command with -v parameter and the message I get after a successful login is: debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = en_GB.utf8 Still the cursor keeps blinking on a new line without a prompt. However, Putty SSH client works perfectly on the same machine. Thank you very much for your time. Your help would be greating appreciated.

  Read the article

• NRPE: Unable to read output with check_connections plugin

  - by Wlodzimierz

  I'm using plugin which gives me warning or crtis with established connections. If I run it on local machine it gives: *root@graber:/usr/lib/nagios/plugins# ./check_connections -w 1 -c 5 -C sshd CRITICAL Established connections: 6* I know, I run as root. But: Rights to the file: root@graber:/usr/lib/nagios/plugins# ls -all check_connections -rwxr-xr-x 1 nagios nagios 5459 2012-07-06 10:19 check_connections /etc/sudoers: root@graber:/usr/lib/nagios/plugins# cat /etc/sudoers Defaults env_reset root ALL=(ALL:ALL) ALL %admin ALL=(ALL) ALL nagios ALL=(ALL) NOPASSWD: /usr/bin/lsof nagios ALL=(ALL) NOPASSWD: /usr/lib/nagios/plugins/ /etc/nagios/nrpe.cfg: *nrpe_user=nagios nrpe_group=nagios* *dont_blame_nrpe=1* *command_prefix=/usr/bin/sudo command[check_connections]=/usr/lib/nagios/plugins/check_connections -w 1 -c 5 -C sshd* log from remote: *2012-07-06T11:12:49+02:00 graber nrpe[25928]: Handling the connection... 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Host address is in allowed_hosts 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Host is asking for command 'check_connections' to be run... 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Running command: /usr/lib/nagios/plugins/check_connections -w 1 -c 5 -C sshd 2012-07-06T11:19:11+02:00 graber nrpe[26100]: Return Code: 2, Output: NRPE: Unable to read output* Why is this happening? I'm out of ideas, I've searched google for 2 days now :)

  Read the article

• Assistance on setup to Connect an offsite server to the LAN via RRAS VPN - Server 2008 R2

  - by Paul D'Ambra

  I have an office LAN protected using a Zyxel Zywall USG 300. I've set up an L2TP/ipsec VPN on that which accepts connections using a shared secret and I've tested this from multiple clients. I have a server offsite and want to set up RRAS to use a persistent connection to the VPN so that it can carry out network jobs even with no one logged in (I'm using it for Micorosft DPM secondary backup). If I create a vpn as if I were setting up a users laptop it can dial in no problem but if I set up a demand dial interface in RRAS it errors. I enable RRAS ticking only demand dial interface (branch office routing) Select network interfaces, right click and choose new demand dial interface Name the VPN ToCompany Select connect using VPN And then L2TP as the vpn type enter the IP address (double-checked for typos!) select Route IP packets on this interface specify static route to remote network as 10.0.0.0/24 with metric of 1 add dial out credentials (again double checked for typos and confirmed with other vpn connections click finish now I right-click on the new interface and choose properties and then the security tab I change Data encryption to optional select only PAP for Authentication (both as per manufacturer of Zywall) click advanced settings against type of vpn and set shared secret then I select the new interface, right-click and choose connect this dials and then errors with either 720 or 811 as the error codes. However, if I create a VPN by going to Network & Sharing center and setting up as if I was creating a VPN from my laptop to the office (say) it dials successfully so I know the VPN settings are correct and the machine can connect to the VPN. Suggests very strongly the problem is how I'm setting up RRAS. Can anyone help?

  Read the article

• Is there an SSL equivelent to an ssh agent?

  - by Matthew J Morrison

  Here is my situation: There are a number of developers who all need to have access to be able to install ruby gems and python eggs from a remote source. Currently, we have a server inside our firewall that hosts the gems and eggs. We now want the ability to be able to install things hosted on that server outside of our firewall. Since some of the gems and eggs that we host are proprietary I would like to somewhat lock access to that machine down, as unobtrusively as possible to the developers. My first thought was using something like ssh keys. So, I spent some time looking at SSL mutual authentication. I was able to get everything set up and working correctly, testing with curl, but the unfortunate thing was that I had to pass extra arguments to curl so it knows about the certificate, key and certificate authority. I was wondering if there is anything like the ssh agent that I can set up to provide that information automatically so that I can push the certificates and keys to the developer's machines so the developers don't have to log in or provide keys each time they try to install something. Another thing that I want to avoid is having to modify the 'gem' command and the 'pip' command to provide keys when they make the http connection. Any other suggestions that may solve this problem (not related to ssl mutual auth) are also welcome. EDIT: I've been continuing to research this and I came across stunnel. I think this may be what I'm looking for, any feedback regarding stunnel would also be great!

  Read the article

• Windows 7 pc freezes for an indeterminate amount of time after unlocking

  - by pikes

  Not sure if this type of question is appropriate for this forum, but I've tried everything I can think of to solve this problem aside from format/reinstall. I recently got a new work PC (Dell optiplex 755) with windows 7 professional x64. Standard developer software installed for .net development: VS2008, VS2005, SQL management studio, office 2007, etc. Recently I've been having this weird problem where after I lock my pc, when I try to unlock it, the screen will be black for awhile after unlocking. I can ctl+alt+del and put my password in but then it just goes black. The amount of time on the black screen seems to be related to the amount of time I am away from my PC. If only away a few minutes, it'll take about a minute to get to the desktop. If away for an hour, could take up to 15 minutes. If I lock it and go home for the night, I have to restart my PC in the morning (I've let it sit for an hour after a night of being locked and nothing happened). It doesn't do it every time but definitely the majority of the time. One weird thing I've seen is that if I remote into my machine before trying to log back in it does not do it. I uninstalled all software back to the point when I remember it started happening and it still does it. I was using this PC for a few weeks without this problem happening at all. Anyone know what my next troubleshooting steps could be? My IT department tried to fix it by moving my old profile to another disk and having me log in, effectively recreating a profile from scratch but that didn't solve it. As I said above if this isn't the right forum for these types of questions please let me know. Thanks in advance!

  Read the article

• How do I correctly SSH port forward using LiveReload on Redhat?

  - by program247365

  Referencing this page: http://feedback.livereload.com/knowledgebase/articles/86280-if-you-edit-files-directly-on-your-server It says you can remotely port forward the LiveReload specific port of 35729, using this command: ssh -L 35729:127.0.0.1:35729 mylogin@myremoteserverIP When I run the -v option, I get: debug1: Local connections to LOCALHOST:35729 forwarded to remote address 127.0.0.1:35729 debug1: Local forwarding listening on ::1 port 35729. debug1: channel 0: new [port listener] debug1: Local forwarding listening on 127.0.0.1 port 35729. debug1: channel 1: new [port listener] debug1: channel 2: new [client-session] debug1: Entering interactive session. debug1: Sending environment. debug1: client_input_channel_req: channel 2 rtype [email protected] reply 1 debug1: Connection to port 35729 forwarding to 127.0.0.1 port 35729 requested. debug1: channel 3: new [direct-tcpip] channel 3: open failed: connect failed: Connection refused debug1: channel 3: free: direct-tcpip: listening port 35729 for 127.0.0.1 port 35729, connect from 127.0.0.1 port 63673, nchannels 4 I thought editing my /etc/services with this line, would work, but it doesn't: livereload 35729/tcp # livereload usage with guard-livereload Every time I attempt to connect with the browser extension, I believe It's getting blocked by my server. What am I missing here? Do I need to edit /etc/services for this to work?

  Read the article

• Multiple static WAN IP addresses to single LAN subnet

  - by Jessy Houle

  Below is my home network topology. I currently have 5 static IP addresses, 3 of which are in use by 3 routers. These routers in-turn subnet internal networks and port forward. I use my SSL VPN appliance to remote home from work or on the road. At this point I can remotely administer my Windows Server. I know the network is setup wrong, I was matching existing hardware the best I knew how. http://storage.jessyhoule.com.s3.amazonaws.com/network_topology.jpg Ok this said, here is the problem... One of my websites on my Windows Server now needs to be secure (SSL using port 443). However, I'm already port forwarding port 443 to my VPN appliance. Furthermore, if I'm going to have to reconfigure the network, I would really like to be able to use the SSL VPN to remotely administer all machines. I mentioned this to a friend of mine, who said that what I was looking for was a firewall. Explaining that a firewall would take in multiple static (WAN) IP addresses, and still allow all internal devices to be on the same network. So, basically, I could supply my SSL VPN appliance it's very own static (WAN) IP address routing, and yet have it on the same internal network (192.168.1.x) as all my other devices. The first question is... Does this sound right? Secondly, would you suggest anything different? And, finally, what is the cheapest way to do this? I am started down the road of downloading/installing untangle and smoothwall to see if they will do the job, hoping they take multiple static (WAN) IP addresses. Thank you in advance for your answers. -Jessy Houle

  Read the article

• Windows 8 folder to folder sync software

  - by Danny

  I'm looking for direct folder to folder synchronization in Windows 8. I was previously using Live Mesh to accomplish this, but now it looks like that is no longer an option. Note that I'm talking about direct folder to folder sync between different computers, not syncing to the cloud. I'm aware of products like Google Drive, SkyDrive, Dropbox, etc. The problem with them is the space limitation. Basically, I was syncing important files before between my desktop and all of my laptops. One folder for example is My Pictures. This folder has almost 40 gigs of files, which is why the options listed above are not going to work for me. Just need direct syncing, nothing stored on the cloud. I was told by a Microsoft employee that SkyDrive would be replacing Mesh and would provide all the same functionality. So far this looks to be completely false, since the ability to remote desktop is gone along with folder to folder sync. Unless I'm just missing something?

  Read the article

• Msg 10054, Level 20, State 0, Line 0 Error when altering a stored procedure to add a couple of curso

  - by doug_w

  We have a home-rolled backup stored procedure that uses xp_cmdshell to create and clean up database backups. We have an instance that is 2005 sp3 that we are trying to deploy this script to. I am at a bit of a loss for why it is not working. When I execute the create it runs for about 30 seconds and yields the following error: Msg 10054, Level 20, State 0, Line 0 A transport-level error has occurred when sending the request to the server. (provider: TCP Provider, error: 0 - An existing connection was forcibly closed by the remote host.) In my tinkering I discovered that by removing the cursors that actually do the work it will allow me to create the stored procedure (not very helpful for me though). If I add the cursors back in using an alter the error returns. I would be curious if someone has experienced this problem and knows of a solution or work around. I am not opposed to posting the source, it is just lengthy. Things I have checked: Error Logs No dump files in the log directory Thanks in advance for the help.

  Read the article

• OpenVPN Server - CPU is pegged out

  - by ericl42

  Hello, I am configuring OpenVPN to act as a SSL tunnel for a remote location. I have OpenVPN1 at our current location acting as a server then OpenVPN2 at the other location that is acting as a client but is also acting as a DHCP server to machines behind it so they are basically connected to the local LAN. Everything is set up fine and I can talk from location A to location B with no problems like everyone is local. I am however having some performance issues. OpenVPN1 CPU is pegged to 100% the entire time I am copying or doing any type of activity through the tunnel. I expect some CPU usage going up but nothing like this. It's really killing my performance. OpenVPN1 is running in ESX right now with 2 gig RAM and 4 procs with unlimited bursting capacity. I am using AES-192 encryption with a 1024 key. Any idea how I can get my CPU down on OpenVPN1 and my download/upload speeds higher between the tunnel? Thanks. edit: Turning down the logging helped boost the throughput a little bit, but I am still fairly shy of where I believe I should be. Also I am still maxed out on the CPU. Does anyone have any ideas? I am really stuck on this. Thanks.

  Read the article

• Is it worth hiring a hacker to perform some penetration testing on my servers ?

  - by Brann

  I'm working in a small IT company with paranoid clients, so security has always been an important consideration to us ; In the past, we've already mandated two penetration testing from independent companies specialized in this area (Dionach and GSS). We've also ran some automated penetration tests using Nessus. Those two auditors were given a lot of insider information, and found almost nothing* ... While it feels comfortable to think our system is perfectly sure (and it was surely comfortable to show those reports to our clients when they performed their due diligence work), I've got a hard time believing that we've achieved a perfectly sure system, especially considering that we have no security specialist in our company (Security has always been a concern, and we're completely paranoid, which helps, but that's far as it goes!) If hackers can hack into companies that probably employ at least a few people whose sole task is to ensure their data stays private, surely they could hack into our small business, right ? Does someone have any experience in hiring an "ethical hacker"? How to find one? How much would it cost? *The only recommendation they made us was to upgrade our remote desktop protocols on two windows servers, which they were able to access because we gave them the correct non-standard port and whitelisted their IP

  Read the article

• Can I trick Carbonite into backing up an external hard drive?

  - by Brian

  I use Carbonite to back up my PC (Windows XP). We were running low on disk space on our home PC (down to 15 GB), so I went out and purchased an external hard drive. However, Carbonite will not back it up. Is it possible to set up Carbonite to backup an external hard drive? I just want the external drive to be extra disk space. From their FAQ: The current version of Carbonite backs up only the files that reside on permanent hard drives on your computer. It will not back up network drives, external drives, and NAS (network accessed storage) drives. If there are files on a remote drive that you wish to include in your Carbonite backup, you should copy the files to a folder on your local hard drive. If the files are on a shared network drive, you could install Carbonite on the computer on which the network shared drive physically exists, and back the files up directly from that computer. Check back soon for a Carbonite service plan that will allow you to back up your external drives.

  Read the article

• Connecting jconsole using SOCKS to Amazon EC2

  - by freshfunk

  I'm trying to use jconsole to view stats on an EC2 instance by using a socks proxy created by SSH. I've tried the various scripts mentioned in the links below but to no avail: http://simplygenius.com/2010/08/jconsole-via-socks-ssh-tunnel.html http://gabrielcain.com/blog/2010/11/02/using-ssh-proxying-to-connect-jconsole-to-remote-cassandra-instances/ I'm running ssh -f -ND 8123 myuser@mymachine and verified that at least Firefox goes through it as a proxy. I then run jconsole -J-DsocksProxyHost=localhost -J-DsocksProxyPort=8123 service:jmx:rmi:///jndi/rmi://ec2-XX-XX-XXX-XXX.compute-1.amazonaws.com:8080/jmxrmi I run netstat -n on my EC2 instance and I see a connection created by my machine. However, the connection eventually disappears and I get a 'channel 2: open failed: connect failed: Operation timed out' from my ssh tunnel. I've opened the jmx port through the security group and I've checked the port on the EC2 instance to make sure it's open (by telnet-ing to it). I'm not sure where to look next. Are there some properties in sshd_config or ssh_config I need to enable for tunneling? Or anything in Mac OS X? I feel like a serious noob but sys administration is really not my strong point. I've spent several hours and can't get this to work.

  Read the article

• Cannot resolve Hostname to IP, but IP to hostname works

  - by blade

  Hi, I have deployed a bunch of windows server VMs on a cloud hosting service. These machines are all joined to a domain controller on the same service, which also hosts DNS. All of the domain-joined machines have dynamic IP (along with the DC). If I try to resolve any of the hostnames remotely, it fails. For example, I am in SQL Server Reporting Services and I need to connect to a remote server. I provide the hostname of the desired target server and this fails, but then if I provide the IP, this works. How can I pass the hostname and have this resolve to IP? Is there anything I need to look for in the DNS server? It has records of the hostnames (in forward lookup I think), but reverse is empty. Isn't it the case that forward lookup resolves ip to hostname and reverse resolves hostname to ip? Also, I don't know what he subnet mask because this is not in my control, so the machines may not be in the same subnet - can this be a cause of the problem? Where is the problem? Thanks

  Read the article

• RRAS Problem routing to central site from RRAS server only?

  - by TomTom

  Given is an office connected to headquarters using a RRAS bridge (2 virtual machines using RRAS to route between the two networks). Naming: The office is A, the RRAS on A is a-lnk. THe headquartters is B, b-lnk the RRAS machine there. The VPN works perfectly - machines can ping and work between the sites. Domain controllers on both ends replicating, DFS working, remote desktop working. All in all... everything is fine. EXCEPT: a-lnk itself can not reach any machine in B. This would normally not be troublesome (noone ever does anything on a-lnk), but there are two exceptions: * a-lnk is supposed to get it's license from a KMS in B, so not being able to reach B means it is not prolonging. * a-lnk is supposed to pull updates from a WSUS in B - and not being able to reach B means - no updates. Given that thigns work (and security is a minor issue - A-lnk is not reachable from the internet as it is behing a NAT hardware anyway) this got not handled for months. I just wan to get this item ticked off now. Anyone an idea what this is? It definitely is not a "dns does not work" or "routing in general is bad" item, as any computer in A can connect to any computer in B, and the other way arount - only the RRAS computer itself seems to do something really awkward. Platform for both: 2008 R2 standard.

  Read the article

• Network Load Balancing, intermittent port problem on Windows Server 2008

  - by Jimmy Chandra

  Trying to troubleshoot an intermittent problem on a Windows Server 2008 NLB. I think it might be related to an NLB issue. We are using Windows Network Load Balancing to balance load for our multiserver SharePoint front ends. Say... Web Front End 1 IP is 192.168.1.100 and Web Front End 2 IP is 192.168.1.101, the NLB is setup to load balance both WFE servers on any incoming traffic to the IP 192.168.1.200. Sometimes we got an intermittent issue where when we try to access the SharePoint site using 192.168.1.200:8080 (say the site is set up to run on port 8080) from a remote client, it will display page not found. Pinging the 192.168.1.200 will give responses, but when trying to telnet to 192.168.1.200:8080 it just won't connect. However, browsing the SharePoint site directly on individual WFE (192.168.1.100 and 192.168.1.101) show no problem whatsoever. My guess also (we didn't get a chance to try it yet, but I think it should work), if I try connecting remotely to individual server, it will respond just fine. But any attempt on trying to connect using the virtual IP (192.168.1.200) will fail miserably. Funny thing is, after a while it will return back to normal. Anyone had similar experience with this type of problem while implementing NLB before? We are doing this in a virtual environment.

  Read the article

• Windows 7 pc freezes for an indeterminate amount of time after unlocking

  - by pikes

  Not sure if this type of question is appropriate for this forum, but I've tried everything I can think of to solve this problem aside from format/reinstall. I recently got a new work PC (Dell optiplex 755) with windows 7 professional x64. Standard developer software installed for .net development: VS2008, VS2005, SQL management studio, office 2007, etc. Recently I've been having this weird problem where after I lock my pc, when I try to unlock it, the screen will be black for awhile after unlocking. I can ctl+alt+del and put my password in but then it just goes black. The amount of time on the black screen seems to be related to the amount of time I am away from my PC. If only away a few minutes, it'll take about a minute to get to the desktop. If away for an hour, could take up to 15 minutes. If I lock it and go home for the night, I have to restart my PC in the morning (I've let it sit for an hour after a night of being locked and nothing happened). It doesn't do it every time but definitely the majority of the time. One weird thing I've seen is that if I remote into my machine before trying to log back in it does not do it. I uninstalled all software back to the point when I remember it started happening and it still does it. I was using this PC for a few weeks without this problem happening at all. Anyone know what my next troubleshooting steps could be? My IT department tried to fix it by moving my old profile to another disk and having me log in, effectively recreating a profile from scratch but that didn't solve it. As I said above if this isn't the right forum for these types of questions please let me know. Thanks in advance!

  Read the article

• Is timeout in tracertoutput an indication of an error?

  - by nitramk

  TCP/IP packages sent from my computer to a remote server does not always reach destination and ends up being retransmitted sometimes several times before they succeed. To troubleshoot this, I'm running a tracert to the server: Tracing route to <site> [<address>] Over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms mymachine 2 <1 ms <1 ms <1 ms gw.levonline.com [217.70.32.30] 3 <1 ms <1 ms <1 ms 81.201.213.218 4 <1 ms <1 ms <1 ms bmf1-hmf1.driften.net [81.201.213.12] 5 <1 ms <1 ms <1 ms 10ge-2-4-cr2.a1.sth.ownit.se [84.246.88.157] 6 <1 ms * <1 ms netnod-ix-ge-b-sth-4470.microsoft.com [195.69.11.181] 7 26 ms * * ge-3-0-0-0.ams-64cb-1a.ntwk.msn.net [207.46.42.1] 8 48 ms 57 ms 56 ms ten9-1.lts-76e-1.ntwk.msn.net [207.46.42.133] 9 * * * Request timed out. In step 6 and 7, I'm seeing timeouts while waiting for the reply from the server (as seen above). Running the same tracert many times gives varying output, sometimes the response is fine, but sometimes I get this timeout 1, 2 and sometimes for all 3 packets. The timeout always starts at the same server, netnod-ix-ge-b-sth-4470.microsoft.com. I've tried setting the tracert timeout to 10 seconds, but am still getting the timeout. Running tracert towards other servers does not give me the same timeout. Microsoft network technicians tells me that the problem is not on "their" side. Are these timeouts an indicator of a lost packet on the specific node which did not respond? Are the timeouts an indication of there being a problem, or is it normal?

  Read the article

• Share Exchange Calendar Outside Organization

  - by CalCurious

  I'm trying to figure out the best way to meet a user's (Corp-A-User) request to share their calendar with someone at another company (Corp-B-User). We're running Microsoft SBS 2008 with Exchange 2007 and SharePoint. The remote user is running Exchange, version unknown. Corp-A-User wants to give the Corp-B-User the ability to create appointments on Corp-A-User's calendar. This will naturally require sharing of Free/Busy information. Corp-A-User naturally lacks the vision to seen ANY problem with giving Corp-B-User full access to their calendar. But, I see the problems with that and would prefer that Corp-B-User have only the ability to see Free/Busy and create appointments. Most of the external publishing options that I have thought of, such as WebDav, allow displaying a user's calendar, but there are problems with security and the ability to create appointments. Right now, I'm thinking the cleanest solution would be to use a Google calendar along with Google Calendar Sync for the two user's Outlook clients. But, I'm not sure if there isn't a better way and I hate teh idea of pushing a corporate calendar up to Google. Not to mention the issues likely to pop up from the multiple sync paths. Does any one have a good solution for this scenario that would be willing to share what they use?

  Read the article

• Wake OSX 10.8 over WiFi (WoWL - Wake on WiFi Lan)

  - by WrinkledCheese

  I have a stack of Apple Mac minis running SSH servers for remote login. The problem is that I can't seem to get them to wake up. From what I gathered, as of Mac OSX 10.7 you required to have a boot time option set - darkwake=0 10.7 and darkwake=no 10.8. So I tried this and then I came to the realization that this will probably work for a wired connection but I'm using WiFi. My wired connections are used for another local subnet without Internet access, so I have to get it to wake on WiFi. I realize that I can just set the stack of Mac minis to just not sleep, but I'm looking for a sleep enabled option. These services don't require initial response speed as once the connection is made they will be active and once they are no longer active they will hopefully go back to sleep. I have a FreeBSD box running avahi-daemon in order to try and wake the Macs with the Bonjour Service but it doesn't seem to work. I tried registering the service as Gordon suggested in the below post, but that just makes it so that there isn't a timeout when discovering services and resolving them. It still doesn't allow ssh connections to port 22 when it's asleep. For reference, I want what seems like what Gordon Davisson explained on this question: Wake on Demand for Apache server in OS X 10.8

  Read the article

• LVM and cloning HDs

  - by jcea

  Using Linux, I have several backup levels. One of them is a periodical sector by sector copy (using dd) of my laptop harddisk to an external USB disk. Yes, I have other backups too, like remote rsync. This approach (the disk dd) is OK when cloning a HDD with no LVM volumes, since I can plug the external disk anytime and mount the partitions simply mounting /dev/sdb* instead of /dev/sda*. Trivial and handy. Today I moved ALL my harddisk (including the /boot) to LVM. Everything works fine. I will stress it for a couple of days, and then I will do a sector by sector copy to my external harddisk. Now I have a problem, I guess. If in the future I plug the external USB HDD to recover any file, the OS will detect a duplicate LVM configuration, with the same name and the same UUID. Even doing a vgrename (which LVM would be renamed, the internal HDD or the external HDD?), the cloned UUID will not change. Is there any command to change name and UUID? Ideally I would clone the HDD and then change the LVM group name and its UUID, but I don't know how to do it. Another related issue would be... In the past I have booted my laptop using the external disk, using the BIOS boot menu and changing GRUB entries manually to boot from /dev/sdb instead of /dev/sda. But now my current GRUB configuration boots directly from a LVM logical volume, something like: set root='(LVM-root)' in my grub.cfg. So... What is going to happen with duplicated volumes? Any suggestion? I guess I could repartition my external harddisk and change backup strategy from dd to rsync, but this disk has windows installed too, and I really would like to have a physical "real" copy.

  Read the article

• Virtual Machine Network Architecture, Isolating Public and Private Networks

  - by Mark

  I'm looking for some insight into best practices for network traffic isolation within a virtual environment, specifically under VMWARE ESXi. Currently I have (in testing) 1 hardware server running ESXi but i expect to expand this to multiple pieces of hardware. The current setup is as follows: 1 pfsense VM, this VM accepts all outside (WAN/internet) traffic and performs firewall/port forwarding/NAT functionality. I have multiple public IP addresses sent to the this VM that are used for access to individual servers (via per incoming IP port forwarding rules). This VM is attached to the private (virtual) network that all other VMs are on. It also manages a VPN link into the private network with some access restrictions. This isn't the perimeter firewall but rather the firewall for this virtual pool only. I have 3 VMs that communicate with each other, as well as have some public access requirements: 1 LAMP server running an eCommerce site, public internet accessible 1 accounting server, access via windows server 2008 RDS services for remote access by users 1 inventory/warehouse management server, VPN to client terminals in warehouses These servers constantly talk with each other for data synchronization. Currently all the servers are on the same subnet/virtual network and connected to the internet through the pfsense VM. The pfsense firewall uses port forwarding and NAT to allow outside access to the servers for services and for server access to the internet. My main question is this: Is there a security benefit to adding a second virtual network adapter to each server and controlling traffic such that all server to server communication is on one separate virtual network, while any access to the outside world is routed through the other network adapter, through the firewall, and on the the internet. This is the type of architecture i would use if these were all physical servers, but i'm unsure if the networks being virtual changes the way i should approach locking down this system. Thank you for any thoughts or direction to any appropriate literature.

  Read the article

• Exchange Connector Won't Send to External Domains

  - by sisdog

  I'm a developer trying to get my .Net application to send emails out through our Exchange server. I'm not an Exchange expert so I'll qualify that up front!! We've set up a receive Connector in Exchange that has the following properties: Network: allows all IP addresses via port 25. Authentication: Transport Layer Security and Externally Secured checkboxes are checked. Permission Groups: Anonymous Users and Exchange Servers checkboxes are checked. But, when I run this Powershell statement right on our Exchange server it works when I send to a local domain address but when I try to send to a remote domain it fails. WORKS: C:\Windows\system32Send-Mailmessage -To [email protected] -From [email protected] -Subject testing -Body testing -SmtpServer OURSERVER (BTW: my value for OURSERVER=boxname.domainname.local. This is the same fully-qualified name that shows up in our Exchange Management Shell when I launch it). FAILS: C:\Windows\system32Send-Mailmessage -To [email protected] -From [email protected] -Subject testing -Body testing -SmtpServer OURSERVER Send-MailMessage : Mailbox unavailable. The server response was: 5.7.1 Unable to relay At line:1 char:17 + Send-Mailmessage <<<< -To [email protected] -From [email protected] -Subject testing -Body himom -SmtpServer FTI-EX + CategoryInfo : InvalidOperation: (System.Net.Mail.SmtpClient:SmtpClient) [Send-MailMessage], SmtpFailed RecipientException + FullyQualifiedErrorId : SmtpException,Microsoft.PowerShell.Commands.SendMailMessage EDIT: From @TheCleaner 's advice, I ran the Add-ADPermission to the relay and it didn't help; [PS] C:\Windows\system32Get-ReceiveConnector "Allowed Relay" | Add-ADPermission -User "NT AUTHORITY\ANONYMOUS LOGON" -E xtendedRights "Ms-Exch-SMTP-Accept-Any-Recipient" Identity User Deny Inherited -------- ---- ---- --------- FTI-EX\Allowed Relay NT AUTHORITY\ANON... False False Thanks for the help. Mark

  Read the article

< Previous Page | 348 349 350 351 352 353 354 355 356 357 358 359  | Next Page >