Search Results

Search found 12768 results on 511 pages for 'little snitch'.

Page 353/511 | < Previous Page | 349 350 351 352 353 354 355 356 357 358 359 360  | Next Page >

• Juniper NetScreen NS-5GT traffic monitoring

  - by blah

  I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

  Read the article

• Bad performance with Linux software RAID5 and LUKS encryption

  - by Philipp Wendler

  I have set up a Linux software RAID5 on three hard drives and want to encrypt it with cryptsetup/LUKS. My tests showed that the encryption leads to a massive performance decrease that I cannot explain. The RAID5 is able to write 187 MB/s [1] without encryption. With encryption on top of it, write speed is down to about 40 MB/s. The RAID has a chunk size of 512K and a write intent bitmap. I used -c aes-xts-plain -s 512 --align-payload=2048 as the parameters for cryptsetup luksFormat, so the payload should be aligned to 2048 blocks of 512 bytes (i.e., 1MB). cryptsetup luksDump shows a payload offset of 4096. So I think the alignment is correct and fits to the RAID chunk size. The CPU is not the bottleneck, as it has hardware support for AES (aesni_intel). If I write on another drive (an SSD with LVM) that is also encrypted, I do have a write speed of 150 MB/s. top shows that the CPU usage is indeed very low, only the RAID5 xor takes 14%. I also tried putting a filesystem (ext4) directly on the unencrypted RAID so see if the layering is problem. The filesystem decreases the performance a little bit as expected, but by far not that much (write speed varying, but 100 MB/s). Summary: Disks + RAID5: good Disks + RAID5 + ext4: good Disks + RAID5 + encryption: bad SSD + encryption + LVM + ext4: good The read performance is not affected by the encryption, it is 207 MB/s without and 205 MB/s with encryption (also showing that CPU power is not the problem). What can I do to improve the write performance of the encrypted RAID? [1] All speed measurements were done with several runs of dd if=/dev/zero of=DEV bs=100M count=100 (i.e., writing 10G in blocks of 100M). Edit: If this helps: I'm using Ubuntu 11.04 64bit with Linux 2.6.38. Edit2: The performance stays approximately the same if I pass a block size of 4KB, 1MB or 10MB to dd.

  Read the article

• Please help to find a solution for two way, real-time synchronization on Centos 5.5 64Bit

  - by Vipul Limbachiya

  I am in need of a real time, two way synchronization software for Centos 5.5 / 64Bit. Here's little explanation: It needs to be able to perform: Two way synchronization. It must be realtime. By realtime means it can be almost realtime, i.e. a delay of 1 second for example is fine. And the folders are on the same server. I am currently using GlusterFS across two webservers. However, it has extremely poor small file read performance and it's slowing down my website. There's nothing more that can be done to improve this, I have already tested many configurations. As a solution, I was going to mount a RAM drive (tmpfs) that mirrors the GlusterFS web files but get the webserver to use the RAM drive. The issue is that I need two way realtime mirroring or replication between glusterfs and the RAM drive. I need this is as Apache writes files as wells. As I said, realtime two way synchronization across two folders. Which are in fact 2 different mounts points. The RAM (tmpfs) mount poing and the GlusterFS mount point. I already know about: Rsync - Which is one way Unison - Which is not realtime Please suggest me any solution free or paid. Thanks in advance

  Read the article

• Poor write performance on Debian server running NFS with 22TB exported JFS filesystem

  - by user143546

  I am currently running a debian server that is exporting a large JFS filesystem (22TB) over NFS (nfs-kernel-server.) When attempting to write to the NFS share, the performance is very poor. The 22TB disk is sitting on a NAS mounted using iSCSI. It will bust for a moment near expected line speed, and then sit idle for several seconds. Very little traffic measured in the low kb/sec. The wait peeks on write. When reading from the NFS mount, the system operates at expected speeds (11MB/sec). The issue does not occur when using SFTP, rsync, or local coping (non-nfs). The issue persists between stable and testing releases. On the same machine I have a 14TB ext4 filesystem using the exact same export configuration that does not share the issue. This share is not in regular use and thus not consuming resources. NFS Server: cat /etc/exports /data2 10.1.20.86(rw,no_subtree_check,async,all_squash) cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /etc/default/nfs-kernel-server RPCNFSDCOUNT=8 RPCNFSDPRIORITY=0 RPCMOUNTDOPTS=--manage-gids NEED_SVCGSSD= RPCSVCGSSDOPTS= NFS Client: cat /etc/fstab 10.1.20.100:/data2 /root/incoming nfs rw,noatime,soft,intr,noacl 0 2 cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /proc/mounts 10.1.20.100:/data2/ /root/incoming nfs4 rw,noatime,vers=4,rsize=262144,wsize=262144,namlen=255,soft,proto=tcp,port=0,timeo=600,retrans=2,sec=sys,clientaddr=10.1.20.86,minorversion=0,addr=10.1.20.100 0 0 This problem has me pretty stumped. Any help would be greatly welcomed. Thanks.

  Read the article

• Requests are making it to my app server, but not into node.js -- why?

  - by Zane Claes

  I detailed in this question on StackOverflow how some random requests are not making it from the client to my Node.js app server, resulting in a gateway timeout. In summary, identical requests are, at random, not even making it far enough to trigger a console.log() in my first line of express middleware. I need to narrow down the problem, though, to find out WHERE the traffic is being lost and it was suggested that I try a packet sniffer on my app servers. Here's my setup: 2x Load Balancers (m1.larges) 2x node.js servers (also m1.large) Here's what's interesting/unusual: the node.js servers started as PHP servers with an Apache stack and continue to serve PHP files for my domain (streamified.me). However, I use a little httpd.conf magic on the app servers so that requests to api.streamified.me get routed over port 8888 to the node.js server: RewriteCond %{HTTP_HOST} ^api.streamified.me RewriteRule ^(.*) http://localhost:8888$1 [P] So, the request hits the load balancer = goes to an app server = gets routed to port 8888 if it's intended for the API = gets handled by node.js So, in the same httpd.conf file, I turned on RewriteLogLevel 5 and then created a simple PHP+CURL script on my localhost to hit my api.streamified.me with a random URL (which should cause node.js to trigger a simple "not found" response) until it resulted in a Gateway timeout. Here, you can see that it has happened -- and the rewrite log shows that the request was definitely received by the app server and forwarded to port 8888... but it was never received by node.js (or, at least, the first line of code in the first line of middleware never gets it...) Image Link: http://i.stack.imgur.com/3OQxS.png

  Read the article

• Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

  - by alexleonard

  I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

  Read the article

• Random server lag, no CPU/mem/pagefile usage

  - by Kev

  We have a fairly new server running Windows 2003 SP2, and the past few days we've noticed random slowdowns. When I'm logged into the server over remote desktop while this is happening, or if I'm physically sitting at the server logged in, suddenly everything becomes extremely laggy. Any UI element I try to interact with takes upwards of ten seconds to react, and then responds very slowly. Then a minute later everything is quite snappy again. During this, I have Task Manager minimized to the tray, and there's no CPU usage. I open it up right after this happens, and there's very little CPU usage on the graph, and no memory or pagefile usage above normal. (Normal being 1.5 GB free in the case of memory.) This is what I see logged into the server, and then users start calling saying things are slow, timing out, and failing--anything to do with our server. No events in the Event Viewer around the times this happens. The context I'm working in (last thing I clicked, etc.) seems different every time--different programs active, different combinations of programs open. Never anything particularly stressful (like adding an event entry to a Cobian Backup configuration, or editing text in TextPad, which has been exceptionally stable in my extensive usage of it.) I would've thought it was just the server, but a family member's home PC (entirely separate) running WinXPSP3 had the same thing happen to it last night a few times. Is this some new behaviour introduced by the latest Windows Updates? Either way, where do I even start to look when nothing seems to be chewing up resources?

  Read the article

• In APC+PHP, how much RAM is too much? Is it okay to set apc.shm_size to many GB?

  - by Jeremy Clarke

  On our server we have a LOT of RAM for our traffic levels (16GB). The HTTP processes regularly eat up all CPU and need to be restarted without even getting close to using swap memory, so I'm looking for ways to spend RAM to ease the load on Apache (and/or help the seperate MySQL server which may be breaking Apache). I have many WordPress installs on the HTTPD instance so APC sometimes uses as much as 900MB of ram (according to the apc.php charts). Just in case I have apc.shm_size set to 1600MB which is more than it needs but not more than I can spare. This means there is usually lots of extra RAM available to APC but also very little turnover and fragmentation is never more than 1%. Is this dangerous? Should I be slimming down APC to less than 1GB just on principle? Should I be expecting some turnover within APC in the name of bringing it's overall footprint down? Having so much memory devoted to APC means that in top/htop every single httpd process shows ~1.9GB in the VIRT memory column. Obviously this is shared memory and not used per-process, but could it be hurting our server? NOTE: The problem with the server remains unclear but the effect is that about 60 times a day all 8 CPU's fill up to 100% and everything stops working until Monit sees that Apache is broken and restarts it (Monin also saves the MySQL server). I'm not sure if APC is even part of the problem but I'm trying to optimize everything just in case.

  Read the article

• Which revision control system for single user

  - by G. Bach

  I'm looking to set up a revision control system with me as a single user. I'd like to have access (read and write) protected using SSL, little overhead, and preferrably a simple setup. I'm looking to do this on my own server, so I don't want to use the option of registering with some professional provider of such a service (I like having direct control over my data; also, I'd like to know how to set up something like that). As far as I'm aware, what kind of project I want to subject to revision control doesn't really matter, but just for completeness' sake, I'm planning on using this for Java project, some html/css/php stuff, and in the future possibly as a synchronizing tool for small data bases (ignore that later one if it doesn't fit in with the paradigm of revision control). My questions primarily arise from the fact that I only ever used Subversion from Eclipse, so I don't have thorough knowledge of what's out there, what fits better for which needs, etc. So far I've heard of Subversion, Git, Mercurial, but I'm open to any system that's widely used and well supported. My server is running Ubuntu 11.10. Which system should I choose, what are the advantages of the respective systems, and if you know of any particularly useful ones, are there tutorials regarding the setup of the system I should choose that you could recommend?

  Read the article

• What mobile phones are viable for a "nerdy" person? [closed]

  - by Blixt

  This community wiki is for determining a list of good mobile phone choices if you are "nerdy" (definition follows.) As a point of reference, the almost two years old N95 8GB will be used. Mostly because that's what I can most relate to since I've had it since it came out. Today, iPhone and other modern mobile phones really out-shine it in usability and interface. However, it still does everything I want it to do (and here's the definition of "nerdy"; modify as needed): Syncs contacts, calendar, tasks and mail in the background Can run multiple installable applications in the background (Google Maps with Latitude, for example) Good amount of space for music etc. Lets you develop your own little toy applications (Python; not to mention it can also run an Apache server with a public URL!) Tethering! Supports Flash (maybe not very important, but it has its uses) Has a manufacturer that believes in the nerdiness! (The people at Nokia Labs make lots of cool stuff and share early versions with the community and are generally open) A high resolution screen (at least 320x240) Special hardware features such as an accelerometer and GPS What's missing from the N95 8GB but still qualifies as good, "nerdy", qualities: 7.2 Mbit/s (or faster) internet through HSDPA or HSPA+. A good web browser that can do most of the stuff a desktop browser can (especially render sites properly and run JavaScript correctly) Touch (especially multi-touch) More special hardware features such as a compass Intuitive and fluent user interface (Shiny stuff) Ability to configure it to trust root certificates of my own choice A processor fast enough to run Quake 3! =)

  Read the article

• Retrieve a user's Exchange database in powershell

  - by Paul

  Hey Everyone, I've scoured the interwebs for a few days now off and on to find this. I am creating a powershell script for email-enabling new user's(Exchange 2007). To give you a little background when we have a new hire, their AD account is created at our off-site helpdesk, but they don't create their email account. I'm trying to automate the process of mail-enabling the user which involves putting them in the same database as an existing user, disable imap pop activesync, and lastly email the requester of the ticket. I would like to just get prompted for the New User's name, User to Replicate(mailbox, storage group, database), and the person to email after it's been created. So if someone could just help with a command to Retrieve a user's Exchange database in powershell that would be great, but if people also want to help with my hacked up script please do so as well!!! Here is what I have so far: Write-output “ENTER THE FOLLOWING DETAILS” $DName = Read-Host “User Diplay Name" $RUser = Read-Host "Replicate User(Database Grab)" ***$RData = #get the Replicate user's mailbox database here*** $REmail = #either just use a Read-Host “Requester's Email address" or ask for Requester's name and pipe through their email address by digging for it w/ powershell Enable-Mailbox -Identity "$DName" -Database "$RData" Send-MailMessage -From "John Doe <[email protected]>" -To (put $REmail here which is the Requester's email) -Subject "Test Person's email account" -Body "Test Person's email account has been setup.`n`n`nJohn Doe`nGeneric Company`nSystems Administrator`nOffice: 123.456.7890`[email protected]" -SmtpServer genericexchange.exchange.com

  Read the article

• Multiple Remote Desktop Connection in Windows Server 2003?

  - by Joel Bradley

  My company is transitioning all user PC's to Windows 7 64-Bit in anticipation of the 2014 cutoff for Windows XP support. So far everything has been going great except for one specific piece of software that will not run in Windows 7. The current plan is to give everyone a cheap secondary PC to run this software but I feel that's a little much for software that's not even used all the time, although it is essential. I've suggested we install virtual machines but the company does not want to pay for the XP licences. I have access to a copy of Windows Server 2003 that is no longer being used and I was wondering if it was possible to create a remote desktop server. I know it can be done on a one-to-one basis, but this is a 15 person helpdesk. I'd like to be able to support multiple remote dekstop sessions, each with their own logins and dekstops. Is this possible? Are there any other alternatives to my issue? FYI, I've been told that XP mode is only free for consumers. There are costs when used in a corporate environment.

  Read the article

• 1080p monitor: connected through VGA - perfect, HDMI - awful

  - by develroot

  When I connect my 23" monitor (1920x1080) to my pc through HDMI, I encourage some problems. It's not full screen That's it. There are ~1cm black borders on right and left side and ~0,5cm black borders on the top and the bottom of the monitor. That's pretty frustrating. I tried adjusting overscan, but I can't mannualy type the % of overscan that I need. I can only select between ex. 8 and 10% in AMD Vision Engine Control center, but what I need is 9%. Next, even if i select 10% and the image fits all the corners, but after log off all the settings are lost and I have to do it again and again. Text, images, everything looks blurry That surprised me a lot. Should'nt HDMI quality be better than VGA's one? When connected through HDMI, the text isn't readable. It's like a very low refresh rate, although i'm running at 60Hz. Also the text has something like little shadows, very very annoying. Are there any tips to get the same quality as with VGA, with HDMI ? (running on integrated ATI Radeon HD4200, which, appearently, is the best card I have ever seen in terms of integrated ones)

  Read the article

• Linux Cups raspberry pi offload processing to server

  - by jaredmsaul

  I am interested in setting up a raspberry pi as the local end of a printing solution. In my testing the pi chokes on acting as a complete cups based print server. It seems a little underpowered for some of the ghostscipt processing and other filtering that occurs-- particularly on larger or complex documents the processing time can be 5 or more minutes. My question is can the processing be largely done elsewhere and the prepared end product of the processing chain be fed to the pi for output on the connected printer? So in this scenario any arbitrary document (html, pdf, text) is initially 'printed' on a relatively powerful machine but the output is stored in a file. This file is then grabbed by the pi and with all the heavy work out of the way easily printed using cups. I know files can be pushed through cups in raw mode but I am fuzzy on the pros and cons and the applicability in what I describe. I have tested this with pdftops creating a ps file then feeding that raw to cups and I think it works but it seems like there may be a cleaner solution. This scenario would ideally work for any number of printer types.

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• how do I fix a wrong UUID in grub.cfg?

  - by mozerella

  I run Debian Wheezy alone on my PC and I recently copied the root partition to another with rsync as I found that worked well (I also know about dd and ddrescue but they leave unusable space on the new partition). I generated a new random UUID for the new partition with sudo tune2fs -U random /dev/hda9 and also updated fstab / and /home entries. Then as I know so little about GRUB I used a gui (GRUB Customizer) to probe for the new OS and add an entry to GRUB and the MBR -it makes an /etc/grub.d entry then updates GRUB. On startup, the GRUB list contains the new OS (on sda9) but it boots the first OS (which I copied from -sda5). /boot/grub/grub.cfg contains the new debian OS but it looks like this set root='(hd0,msdos9)' search --no-floppy --fs-uuid --set=root 64662470-0e58-4dfd-90ac-43227d773556 linux /boot/vmlinuz-3.2.0-2-amd64 root=UUID=cc3bca0d-aee4-4b9c-95c2-57212cc36d4d ro quiet initrd /boot/initrd.img-3.2.0-2-amd64 the 1st uuid is of sda9, but the 2nd uuid there is of sda5. I can change the 2nd uuid at startup (with E) and it boots sda9. So how can I get grub.cfg corrected so that the sda9 GRUB list entry boots from sda9 permanently?

  Read the article

• Why does my microwave kill the Wi-Fi?

  - by Ohlin

  Every time I start the microwave in the kitchen, our home Wi-Fi stops working and all devices lose connection with our router! The kitchen and the Wi-Fi router are in opposite ends of the apartment but devices are being used a little here and there. We've been annoyed by the instability of the Wi-Fi for some time and it wasn't until recently we realized it was correlated to microwave usage. After some testing with having the microwave on and off we could narrow down the problem to only occurring when the router is in b/g/n mode and uses a set channel. If I change to b/g mode or set channel to auto then there is no problem any more...but still! The router is a Zyxel P-661HNU ("802.11n Wireless ADSL2+ 4-port Security Gateway" with latest firmware) and the microwave is made by Neff with an effect of 1000W (if this information might be useful to anyone). There is an "internet connection" light on the router and it doesn't go out when the interruption occurs so I think this is only an internal Wi-Fi issue. Now to my questions: What parts of the Wi-Fi can possibly be affected by the microwave usage? Frequency? Disturbances in the electrical system? How can setting Auto on channels make a difference? I thought the different channels were just some kind of separation system within the same frequency spectrum? Could this be a sign that the microwave is malfunctioning and slowly roasting us all at home? Is there any need to be worried? Since we were able to find router settings that cooperate well with our microwave's demand for attention, this question is mainly out of curiosity. But as most people out there...I just can't help the fact that I need to know how it's possible :-)

  Read the article

• Windows thinks outgoing connections are incoming connections?

  - by Slayer537

  I have a rather weird issue.. I'm trying to configure Windows Firewall to block all outgoing connections to a certain app, but allow all incoming. This app is used to transfer files across a network. The reason for this type of setup is to only allow certain users (IP Address) access to the files I have, but to still allow others to see what's available. Since Windows Firewall defaults to allowing all outgoing connections, I made a rule to deny all outgoing connections that were not in the IP ranges I specified. For the incoming connections, I'd like to leave it at allow all, but at the moment it is set to only allow the connections that also have outgoing permissions set. If I blanket say allow all incoming connections, I observe that unauthorized IP Address are able to actually download files, even though their IP was blocked in the outgoing connections. To shed a little more visibility on this, I used NetLimiter to see what was going on. NetLimiter showed me that the connection was an incoming connection. Shouldn't this be an outgoing connection, as I am uploading files to them, not the other way around? Is there a way to make the connection type be correct and show up as outgoing instead of incoming?

  Read the article

• How to setup a hyper-v domain with internet access

  - by fynnbob

  First off let me say that I'm not a network admin or server guy, I know very little about that stuff. What I'm trying to do is setup a virtualized domain using hyper-V. Here is the configuration: Physical Server: 4Mb RAM Windows Server 2008 R2 running Hyper-V Virtual Environment: One Domain Controller running Windows Server 2008 R2 One Client running Windows Server 2008 R2 I have been successful in setting up a virtual domain controller and adding a virtual client to that domain controller but I'm stuck at trying to give the virtual Environment Internet access. I can give the client VM Internet access if I remove them from the virtual domain but once I add them back to the virtual domain, Internet access is gone. I've read articles describing many different ways this can be done (using RRAS with NAT, using a wireless connection, etc...) but all of those articles only cover a small piece of the setup and also seem to be geared towards people who know there way around networking and servers which I don't. I'd like to know more but my thing is software development and I have my hands full trying to keep up with everything in that realm. I simply want to setup a virtual domain with Internet access for testing. Can anyone point me to any "for Dummy's" type information on how to setup this type of environment or can anyone provide this kind of step-by-step help. Any help would be very much appreciated.

  Read the article

• Is there any way to tweak / rotate mouse orientation? Any applications? Registry edits?

  - by calbar

  I've got a very frustrating issue with my new Logitech Marathon Mouse M705. It is absolutely perfect for what I need, with the exception that it tracks on an angle for some reason. What I mean is when you slide the cursor to the left, it trends upward - when you slide to the right, it trends down. Moving the cursor along a flat horizontal line is no longer a natural motion - you need to fight what I suspect is a mechanical error of some kind. Unfortunately, I've already exchanged this mouse once and tested both on different Windows 7 and Mac OS X machines - the problem continues to occur. Is there a software solution for me? I'm incredibly surprised there is no simple way to adjust the orientation... how can every mouse manufacturer possibly adjust their hardware to track to everyone's tastes? What about those who need to flip orientation a full 90 or 180 degrees? I only need to adjust mine a few degrees, but I'm sure that need has arisen as well. Anyway, I'm running the latest SetPoint drivers (6.00) on Windows 7 and there are no orientation options available. I've checked out uberOptions and the M705 isn't supported yet (with the last version update over 6 months ago). MAF Mouse instructions are a very strange series of mouse clicks to activate. This app also seems a little overkill and costs $$ (which I'm willing to pay as a last resort). Is there no universal registry value for mouse orientation? How about for SetPoint drivers specifically? I've done a simple search in regedit without any luck. An XML file somewhere? Anything?

  Read the article

• SQL Server 2000, large transaction log, almost empty, performance issue?

  - by Mafu Josh

  For a company that I have been helping troubleshoot their database. In SQL Server 2000, database is about 120 gig. Something caused the transaction log to grow MUCH larger than normal to over 100 gig, some hung transaction that didn't commit or roll back for a few days. That has been resolved and it now stays around 1% full or less, due to its hourly transaction log backups. It IS my understanding that a GROWING transaction log file size can cause performance issues. But what I am a little paranoid about is the size. Although mainly empty, MIGHT it be having a negative effect on performance? But I haven't found any documentation that suggests this is true. I did find this link: http://www.bigresource.com/MS_SQL-Large-Transaction-Log-dramatically-Slows-down-processing-any-idea-why--2ahzP5wK.html but in this post I can't tell if their log was full or empty, and there is not any replies to the post in this link. So I am guessing it is not a problem, anyone know for sure?

  Read the article

• Can a USB/IDE/SATA adapter be flaky?

  - by Ward

  I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

  Read the article

• How to go about rotating logs which are arbitrary named and placed in deeply nested directories?

  - by Roman Grazhdan

  I have a couple of hosts which are basically a playground for developers. On these hosts, each of them has a directory under /tmp where he is free to do all he wants - store files, write logs etc. Of course, the logs are to be rotated, or else the disc will be 100% full in a week. The files can be plenty, but I've dealt with it with paths like /tmp/[a-e]*/* and so on and lived happily for a while, but as they try new cool stuff on the machine logrotate rules grow ugly and unmanageable, and it's getting more difficult to understand which files hit the glob. Also, logrotate would segfault if asked to rotate a socket. I don't feel like trying to enforce some naming policies in that environment, I think it's going to take quite a lot of time and get people annoyed and still would fail at some point. And I still need to manage the logs, not just rm the dirs at night. So is it a good idea in circumstances like these to write a script which would handle these temporary files? I prefer sticking with standard utilities whenever possible, but here I think logrotate is getting less and less manageable. And probably someone heard of some logrotate alternatives which would work well in such an environment? I don't need emailing logs or some other advanced features, so theoretically some well commented find | xargs would do. P.S. I do have a log aggregator but this stuff is not going to touch my little cute logstash machine.

  Read the article

• Fill down in Excel, but based on multiple values

  - by Jenn D.

  I have spreadsheets (not created by me) that have blank entries in one column where they should really have data. I want to take every empty cell and fill it with the nearest value above it. I'm looking for as little manual intervention as possible, because I'll have to do it repeatedly. I thought some previous version of Excel, or maybe another spreadsheet from the distant past, would do this by default -- that is, if you selected the column with foo and bar, and chose the equivalent of "fill down", you would get what's in the WANT column. What I actually get in Excel is the GET column. HAVE: WANT: GET: foo 1 foo 1 foo 1 2 foo 2 foo 2 bar 1 bar 1 foo 1 2 bar 2 foo 2 3 bar 3 foo 3 I'm worried that this might need a macro to be done properly. I used to be a whiz with Excel macros, and then suddenly they were all in VB. My fallback position will be to dump the whole thing to CSV and write a Python script, but if there's any way to do it in Excel that would be much preferable. Even if it involves a couple of different manual steps, that's fine; just not one step per group of lines. That is, a process of "copy the column, do X to it, cut and paste it back" would work, but "do X for each occurrence of foo or bar" won't. The files are too big for that. Any thoughts are appreciated!

  Read the article

• How to have LiveJournal delegate my OpenID to something else?

  - by T-Boy

  I understand that if I have full control over my domain, I can set it up so that I can delegate the task of authenticating to another OpenID service provider. The problem is, what I'd like to do is to get the LiveJournal server to pass the authentication to someone else, instead of having LJ doing it. Preferably what I'd like to do is get LiveJournal, when asked by a web site, say, "No, I don't do it anymore -- go to this address". The plan was that this address would then be in a domain I fully control, which then would pass it on to whichever service provider I choose. I don't even know if I've gotten my understanding of OpenID right, if all this shenanigans are necessary, if my question makes sense, or if it's even possible with a service provider like Livejournal. ETA: Doing a little more reading up, and examining the source for my LiveJournal user page, I note that this particular line in the file's <header> area: <link rel="openid.server" href="http://www.livejournal.com/openid/server.bml" /> I suspect that changing this will allow me to forward OpenID requests to whomever I wish, I think; so far so good. Now comes the hard part -- figuring out how to change all of that using LiveJournal's customization options, if that is at all possible (here's hoping I don't need to pay to get that functionality).

  Read the article

< Previous Page | 349 350 351 352 353 354 355 356 357 358 359 360  | Next Page >