Search Results

Search found 12824 results on 513 pages for 'glen little'.

Page 355/513 | < Previous Page | 351 352 353 354 355 356 357 358 359 360 361 362  | Next Page >

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Bad performance with Linux software RAID5 and LUKS encryption

  - by Philipp Wendler

  I have set up a Linux software RAID5 on three hard drives and want to encrypt it with cryptsetup/LUKS. My tests showed that the encryption leads to a massive performance decrease that I cannot explain. The RAID5 is able to write 187 MB/s [1] without encryption. With encryption on top of it, write speed is down to about 40 MB/s. The RAID has a chunk size of 512K and a write intent bitmap. I used -c aes-xts-plain -s 512 --align-payload=2048 as the parameters for cryptsetup luksFormat, so the payload should be aligned to 2048 blocks of 512 bytes (i.e., 1MB). cryptsetup luksDump shows a payload offset of 4096. So I think the alignment is correct and fits to the RAID chunk size. The CPU is not the bottleneck, as it has hardware support for AES (aesni_intel). If I write on another drive (an SSD with LVM) that is also encrypted, I do have a write speed of 150 MB/s. top shows that the CPU usage is indeed very low, only the RAID5 xor takes 14%. I also tried putting a filesystem (ext4) directly on the unencrypted RAID so see if the layering is problem. The filesystem decreases the performance a little bit as expected, but by far not that much (write speed varying, but 100 MB/s). Summary: Disks + RAID5: good Disks + RAID5 + ext4: good Disks + RAID5 + encryption: bad SSD + encryption + LVM + ext4: good The read performance is not affected by the encryption, it is 207 MB/s without and 205 MB/s with encryption (also showing that CPU power is not the problem). What can I do to improve the write performance of the encrypted RAID? [1] All speed measurements were done with several runs of dd if=/dev/zero of=DEV bs=100M count=100 (i.e., writing 10G in blocks of 100M). Edit: If this helps: I'm using Ubuntu 11.04 64bit with Linux 2.6.38. Edit2: The performance stays approximately the same if I pass a block size of 4KB, 1MB or 10MB to dd.

  Read the article

• Requests are making it to my app server, but not into node.js -- why?

  - by Zane Claes

  I detailed in this question on StackOverflow how some random requests are not making it from the client to my Node.js app server, resulting in a gateway timeout. In summary, identical requests are, at random, not even making it far enough to trigger a console.log() in my first line of express middleware. I need to narrow down the problem, though, to find out WHERE the traffic is being lost and it was suggested that I try a packet sniffer on my app servers. Here's my setup: 2x Load Balancers (m1.larges) 2x node.js servers (also m1.large) Here's what's interesting/unusual: the node.js servers started as PHP servers with an Apache stack and continue to serve PHP files for my domain (streamified.me). However, I use a little httpd.conf magic on the app servers so that requests to api.streamified.me get routed over port 8888 to the node.js server: RewriteCond %{HTTP_HOST} ^api.streamified.me RewriteRule ^(.*) http://localhost:8888$1 [P] So, the request hits the load balancer = goes to an app server = gets routed to port 8888 if it's intended for the API = gets handled by node.js So, in the same httpd.conf file, I turned on RewriteLogLevel 5 and then created a simple PHP+CURL script on my localhost to hit my api.streamified.me with a random URL (which should cause node.js to trigger a simple "not found" response) until it resulted in a Gateway timeout. Here, you can see that it has happened -- and the rewrite log shows that the request was definitely received by the app server and forwarded to port 8888... but it was never received by node.js (or, at least, the first line of code in the first line of middleware never gets it...) Image Link: http://i.stack.imgur.com/3OQxS.png

  Read the article

• Frequent freezes with constant disk activity on SSD netbook

  - by SamsLembas

  I am running Arch Linux on an HP Mini 1000 with a SSD. The machine is a little under a year old and fairly heavily used. About a month ago the machine started freezing up. During the freezes, the system is almost completely unresponsive, seemingly especially for disk-intensive tasks such as launching an application for the first time since reboot. The disk activity led is always constantly illuminated during the freezes. After somewhere between 30 sec and 3 minutes, the machine returns to normal operation. I am pretty sure that the SSD is the source or the problem. Iotop reports a disk transfer rate of 0 during the freezes, so I think it must be getting "stuck" and simply not performing any r/w during the time. I can't seem to find any information on these symptoms on the Internet, so any input on exactly what might be the cause of this would be greatly appreciated. The machine is under warranty, but I would rather not deal with HP until I actually know what is going on. Thanks.

  Read the article

• Please help to find a solution for two way, real-time synchronization on Centos 5.5 64Bit

  - by Vipul Limbachiya

  I am in need of a real time, two way synchronization software for Centos 5.5 / 64Bit. Here's little explanation: It needs to be able to perform: Two way synchronization. It must be realtime. By realtime means it can be almost realtime, i.e. a delay of 1 second for example is fine. And the folders are on the same server. I am currently using GlusterFS across two webservers. However, it has extremely poor small file read performance and it's slowing down my website. There's nothing more that can be done to improve this, I have already tested many configurations. As a solution, I was going to mount a RAM drive (tmpfs) that mirrors the GlusterFS web files but get the webserver to use the RAM drive. The issue is that I need two way realtime mirroring or replication between glusterfs and the RAM drive. I need this is as Apache writes files as wells. As I said, realtime two way synchronization across two folders. Which are in fact 2 different mounts points. The RAM (tmpfs) mount poing and the GlusterFS mount point. I already know about: Rsync - Which is one way Unison - Which is not realtime Please suggest me any solution free or paid. Thanks in advance

  Read the article

• Why can't I get out of display mirror mode?

  - by Roy Smith

  I've been running Ubuntu (10.04.1 LTS, 64-bit) for a while and just replaced my hardware with a faster machine with an ATI Radeon HD 5700 video card. I've got twin 1920 x 1080 displays. I downloaded the latest driver (ati-driver-installer-10-9-x86.x86_64.run) from the ATI web site and installed that. I've gone through a few rounds of playing with /etc/X11/xorg.conf, and can't get things right. At the moment, it's in display mirroring mode, and I can't figure out how to get it out of mirror mode. If I run Monitor Preferences, there's a "Same image in all monitors" checkbox. If I uncheck that, the little preview window switches to show two monitors. When I click Apply, it asks me to log out and log back in again. When I do that, I'm right back to mirrored mode. What's really weird is that I'm currently running a copy of xorg.conf from a coworker's machine. He's got identical hardware, and his display works fine. So, I'm inclined to think there's something else going on other than the conf file. Any ideas what might be wrong?

  Read the article

• which virtualization technology is right for me?

  - by Chris

  I need a little help with this getting this sorted out. I want to setup a linux virtual server that I can use to run both sever and desktop systems. I want a linux system that is minimalist in nature as all the main os will be doing is acting as a hypervisor. The system I'm trying to setup will be running a file server, windows 7, ubuntu 10.04, windows xp and a firewall/gateway security system. All the client OS'es accessing and storing files on the file server. Also all network traffic will be routed through the gateway guest os. The file sever will need direct disk access while the other guests can run one disk images. All of this will be running on the same computer so I wont be romoting in to access the guests OS'es. Also if possible I would like to be able to use my triple head setup in the guest OS'es. I've looked at Xen, kvm and virtualbox but I don't know which is the best for me. I'm really debating between kvm and virtual box as kvm seem to support direct hardware access.

  Read the article

• Which revision control system for single user

  - by G. Bach

  I'm looking to set up a revision control system with me as a single user. I'd like to have access (read and write) protected using SSL, little overhead, and preferrably a simple setup. I'm looking to do this on my own server, so I don't want to use the option of registering with some professional provider of such a service (I like having direct control over my data; also, I'd like to know how to set up something like that). As far as I'm aware, what kind of project I want to subject to revision control doesn't really matter, but just for completeness' sake, I'm planning on using this for Java project, some html/css/php stuff, and in the future possibly as a synchronizing tool for small data bases (ignore that later one if it doesn't fit in with the paradigm of revision control). My questions primarily arise from the fact that I only ever used Subversion from Eclipse, so I don't have thorough knowledge of what's out there, what fits better for which needs, etc. So far I've heard of Subversion, Git, Mercurial, but I'm open to any system that's widely used and well supported. My server is running Ubuntu 11.10. Which system should I choose, what are the advantages of the respective systems, and if you know of any particularly useful ones, are there tutorials regarding the setup of the system I should choose that you could recommend?

  Read the article

• Spreadsheet application that can handle big data OS X

  - by Peter

  I've been working with Excel for quite a while for some statistical analysis that I do regularly. The size of the data that I'm working with has gotten much larger as of late, however. The layout of the databases in question is quite simple, usually just three rows which includes a UNIX timestamp, and EST value, a proprietary numeric value and finally an average of the rows that have a timestamp +/- 1000 that row's timestamp (little AVERAGEIFS() formula). That formula and the EST conversion are the only formulas in the sheet. I'm beginning to work with files with 500,000+ rows. Running the average formula down the entire row takes forever. The end result is the production of print-worthy graphs. I'm looking for either a UNIX CL utility or separate spreadsheet/database application that can handle this amount of data without melting my CPU or making me wait an hour. Is there anything out there? TL;DR: Simple excel sheet with over half a million rows is getting too slow to work with. OS X alternatives?

  Read the article

• Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

  - by alexleonard

  I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

  Read the article

• Borked ubuntu uninstall - need to delete boot partition (i think)

  - by Max Williams

  I just got a new pc laptop with windows 7 and wanted to install Ubuntu on it. Which i did, no problem there, by downloading the installer, burning it to dvd then booting off the dvd and installing. Then, i realised that the new Ubuntu 12.04 uses the Unity desktop, which i immediately disliked, and after some research, began to hate. So, i decided (after a little googling) to install Linux Mint instead. So, thinking i'd better start from scratch, i went to the Windows 7 disk manager and wiped the Ubuntu partition that had been created. Now, when i start up, i get an error from grub, the ubuntu boot manager: error: unknown filesystem grub rescue> _ and a blinking cursor where i can enter commands. I suspect that what i've done is deleted the main ubuntu partition but NOT deleted another partition which is a boot partition, or something like that? Can anyone tell me how i can rescue or unbork this? I'd like to either a) get back to my original windows-only setup OR b) install linux mint off dvd (which i have), into the empty partition, fixing any grub confusion in the process. Any suggestions? Thanks, max BTW please don't answer if you're just going to tell me to stick with 12.04, or install a different distro or something. I definitely want Mint and just want to fix this mess - thanks :)

  Read the article

• Poor write performance on Debian server running NFS with 22TB exported JFS filesystem

  - by user143546

  I am currently running a debian server that is exporting a large JFS filesystem (22TB) over NFS (nfs-kernel-server.) When attempting to write to the NFS share, the performance is very poor. The 22TB disk is sitting on a NAS mounted using iSCSI. It will bust for a moment near expected line speed, and then sit idle for several seconds. Very little traffic measured in the low kb/sec. The wait peeks on write. When reading from the NFS mount, the system operates at expected speeds (11MB/sec). The issue does not occur when using SFTP, rsync, or local coping (non-nfs). The issue persists between stable and testing releases. On the same machine I have a 14TB ext4 filesystem using the exact same export configuration that does not share the issue. This share is not in regular use and thus not consuming resources. NFS Server: cat /etc/exports /data2 10.1.20.86(rw,no_subtree_check,async,all_squash) cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /etc/default/nfs-kernel-server RPCNFSDCOUNT=8 RPCNFSDPRIORITY=0 RPCMOUNTDOPTS=--manage-gids NEED_SVCGSSD= RPCSVCGSSDOPTS= NFS Client: cat /etc/fstab 10.1.20.100:/data2 /root/incoming nfs rw,noatime,soft,intr,noacl 0 2 cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /proc/mounts 10.1.20.100:/data2/ /root/incoming nfs4 rw,noatime,vers=4,rsize=262144,wsize=262144,namlen=255,soft,proto=tcp,port=0,timeo=600,retrans=2,sec=sys,clientaddr=10.1.20.86,minorversion=0,addr=10.1.20.100 0 0 This problem has me pretty stumped. Any help would be greatly welcomed. Thanks.

  Read the article

• Why does my microwave kill the Wi-Fi?

  - by Ohlin

  Every time I start the microwave in the kitchen, our home Wi-Fi stops working and all devices lose connection with our router! The kitchen and the Wi-Fi router are in opposite ends of the apartment but devices are being used a little here and there. We've been annoyed by the instability of the Wi-Fi for some time and it wasn't until recently we realized it was correlated to microwave usage. After some testing with having the microwave on and off we could narrow down the problem to only occurring when the router is in b/g/n mode and uses a set channel. If I change to b/g mode or set channel to auto then there is no problem any more...but still! The router is a Zyxel P-661HNU ("802.11n Wireless ADSL2+ 4-port Security Gateway" with latest firmware) and the microwave is made by Neff with an effect of 1000W (if this information might be useful to anyone). There is an "internet connection" light on the router and it doesn't go out when the interruption occurs so I think this is only an internal Wi-Fi issue. Now to my questions: What parts of the Wi-Fi can possibly be affected by the microwave usage? Frequency? Disturbances in the electrical system? How can setting Auto on channels make a difference? I thought the different channels were just some kind of separation system within the same frequency spectrum? Could this be a sign that the microwave is malfunctioning and slowly roasting us all at home? Is there any need to be worried? Since we were able to find router settings that cooperate well with our microwave's demand for attention, this question is mainly out of curiosity. But as most people out there...I just can't help the fact that I need to know how it's possible :-)

  Read the article

• Random server lag, no CPU/mem/pagefile usage

  - by Kev

  We have a fairly new server running Windows 2003 SP2, and the past few days we've noticed random slowdowns. When I'm logged into the server over remote desktop while this is happening, or if I'm physically sitting at the server logged in, suddenly everything becomes extremely laggy. Any UI element I try to interact with takes upwards of ten seconds to react, and then responds very slowly. Then a minute later everything is quite snappy again. During this, I have Task Manager minimized to the tray, and there's no CPU usage. I open it up right after this happens, and there's very little CPU usage on the graph, and no memory or pagefile usage above normal. (Normal being 1.5 GB free in the case of memory.) This is what I see logged into the server, and then users start calling saying things are slow, timing out, and failing--anything to do with our server. No events in the Event Viewer around the times this happens. The context I'm working in (last thing I clicked, etc.) seems different every time--different programs active, different combinations of programs open. Never anything particularly stressful (like adding an event entry to a Cobian Backup configuration, or editing text in TextPad, which has been exceptionally stable in my extensive usage of it.) I would've thought it was just the server, but a family member's home PC (entirely separate) running WinXPSP3 had the same thing happen to it last night a few times. Is this some new behaviour introduced by the latest Windows Updates? Either way, where do I even start to look when nothing seems to be chewing up resources?

  Read the article

• How to setup a hyper-v domain with internet access

  - by fynnbob

  First off let me say that I'm not a network admin or server guy, I know very little about that stuff. What I'm trying to do is setup a virtualized domain using hyper-V. Here is the configuration: Physical Server: 4Mb RAM Windows Server 2008 R2 running Hyper-V Virtual Environment: One Domain Controller running Windows Server 2008 R2 One Client running Windows Server 2008 R2 I have been successful in setting up a virtual domain controller and adding a virtual client to that domain controller but I'm stuck at trying to give the virtual Environment Internet access. I can give the client VM Internet access if I remove them from the virtual domain but once I add them back to the virtual domain, Internet access is gone. I've read articles describing many different ways this can be done (using RRAS with NAT, using a wireless connection, etc...) but all of those articles only cover a small piece of the setup and also seem to be geared towards people who know there way around networking and servers which I don't. I'd like to know more but my thing is software development and I have my hands full trying to keep up with everything in that realm. I simply want to setup a virtual domain with Internet access for testing. Can anyone point me to any "for Dummy's" type information on how to setup this type of environment or can anyone provide this kind of step-by-step help. Any help would be very much appreciated.

  Read the article

• 1080p monitor: connected through VGA - perfect, HDMI - awful

  - by develroot

  When I connect my 23" monitor (1920x1080) to my pc through HDMI, I encourage some problems. It's not full screen That's it. There are ~1cm black borders on right and left side and ~0,5cm black borders on the top and the bottom of the monitor. That's pretty frustrating. I tried adjusting overscan, but I can't mannualy type the % of overscan that I need. I can only select between ex. 8 and 10% in AMD Vision Engine Control center, but what I need is 9%. Next, even if i select 10% and the image fits all the corners, but after log off all the settings are lost and I have to do it again and again. Text, images, everything looks blurry That surprised me a lot. Should'nt HDMI quality be better than VGA's one? When connected through HDMI, the text isn't readable. It's like a very low refresh rate, although i'm running at 60Hz. Also the text has something like little shadows, very very annoying. Are there any tips to get the same quality as with VGA, with HDMI ? (running on integrated ATI Radeon HD4200, which, appearently, is the best card I have ever seen in terms of integrated ones)

  Read the article

• Windows thinks outgoing connections are incoming connections?

  - by Slayer537

  I have a rather weird issue.. I'm trying to configure Windows Firewall to block all outgoing connections to a certain app, but allow all incoming. This app is used to transfer files across a network. The reason for this type of setup is to only allow certain users (IP Address) access to the files I have, but to still allow others to see what's available. Since Windows Firewall defaults to allowing all outgoing connections, I made a rule to deny all outgoing connections that were not in the IP ranges I specified. For the incoming connections, I'd like to leave it at allow all, but at the moment it is set to only allow the connections that also have outgoing permissions set. If I blanket say allow all incoming connections, I observe that unauthorized IP Address are able to actually download files, even though their IP was blocked in the outgoing connections. To shed a little more visibility on this, I used NetLimiter to see what was going on. NetLimiter showed me that the connection was an incoming connection. Shouldn't this be an outgoing connection, as I am uploading files to them, not the other way around? Is there a way to make the connection type be correct and show up as outgoing instead of incoming?

  Read the article

• Mesh Networked servers via vpn

  - by microspino

  I got a design idea and I would like to have some advice from SF about It. I have 5 customers with small real-estate databases. I've built for them a desktop app and now they would like to merge their database to share their data. I don't want to centralize everything in one place nor I want to do maintenance for servers. They told me also, that all of them in their offices, have little servers and maintenance guys available. Although everything seems suitable for web application, I had the idea to experiment something new: Any customer small-server wild be connected to the others in a sort of mesh network without a single point of failure and through VPNs. If one of the servers went down the customers could still connect to their databases from one of the other mesh networked servers instead of from the local one that is down. During normal operations all the servers sync the db with the others through VPNs. I can accept a half-day timing window of NON synched data, in other words, since I don't need real time synchronization, the server don't have to always stay in synch. I can migrate my data over to other Non-Sql technologies like CouchDB or Redis or whatever you suggest. As you can see I don't have a lot of constraints and although I could go with a web application I would like to delegate and decentralize support, data-privacy and management, as more as I can to my customers offices. Is that a crazy idea? Do you know If something similar exist? Which technology would you suggest?

  Read the article

• Juniper NetScreen NS-5GT traffic monitoring

  - by blah

  I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

  Read the article

• DPM server 2010 Attach agent error : administrator privileges missing?

  - by Michael

  I’m hoping you would be able to help me out with this little problem I’m having. I installed DPM 2010 in our test environment to test backups on Exchange 2010 servers. The environment includes : 1xDC 2x Exchange Server 2010 1x DPM 2010 server All of these are running on Microsoft server 2008 R2 Virtual machines. The host machines are using Hyper-v. So the problem goes like this : 1- I tried to install the agents from the DPM server GUI, which failed saying I didn’t have the correct permissions. 2- So then I tried the manual installation using the commands from : the Microsoft site http://technet.microsoft.com/en-us/library/bb870935.aspx 3- The agent installation worked but when I get to attaching the agents to the DPM server it still gives me the error saying that the specified account does not have administrator rights. 4- I tried the Domain admin, users who are domain admin + local admin, single local admins. 5- I have turned off the windows firewall and made sure all the services are running. So now I’m out of ideas and really need help, the agent attach to the DPM server is the last thing that is holding me back from deploying everything to the production site. Any help would be really appreciated.

  Read the article

• Linux Cups raspberry pi offload processing to server

  - by jaredmsaul

  I am interested in setting up a raspberry pi as the local end of a printing solution. In my testing the pi chokes on acting as a complete cups based print server. It seems a little underpowered for some of the ghostscipt processing and other filtering that occurs-- particularly on larger or complex documents the processing time can be 5 or more minutes. My question is can the processing be largely done elsewhere and the prepared end product of the processing chain be fed to the pi for output on the connected printer? So in this scenario any arbitrary document (html, pdf, text) is initially 'printed' on a relatively powerful machine but the output is stored in a file. This file is then grabbed by the pi and with all the heavy work out of the way easily printed using cups. I know files can be pushed through cups in raw mode but I am fuzzy on the pros and cons and the applicability in what I describe. I have tested this with pdftops creating a ps file then feeding that raw to cups and I think it works but it seems like there may be a cleaner solution. This scenario would ideally work for any number of printer types.

  Read the article

• What mobile phones are viable for a "nerdy" person? [closed]

  - by Blixt

  This community wiki is for determining a list of good mobile phone choices if you are "nerdy" (definition follows.) As a point of reference, the almost two years old N95 8GB will be used. Mostly because that's what I can most relate to since I've had it since it came out. Today, iPhone and other modern mobile phones really out-shine it in usability and interface. However, it still does everything I want it to do (and here's the definition of "nerdy"; modify as needed): Syncs contacts, calendar, tasks and mail in the background Can run multiple installable applications in the background (Google Maps with Latitude, for example) Good amount of space for music etc. Lets you develop your own little toy applications (Python; not to mention it can also run an Apache server with a public URL!) Tethering! Supports Flash (maybe not very important, but it has its uses) Has a manufacturer that believes in the nerdiness! (The people at Nokia Labs make lots of cool stuff and share early versions with the community and are generally open) A high resolution screen (at least 320x240) Special hardware features such as an accelerometer and GPS What's missing from the N95 8GB but still qualifies as good, "nerdy", qualities: 7.2 Mbit/s (or faster) internet through HSDPA or HSPA+. A good web browser that can do most of the stuff a desktop browser can (especially render sites properly and run JavaScript correctly) Touch (especially multi-touch) More special hardware features such as a compass Intuitive and fluent user interface (Shiny stuff) Ability to configure it to trust root certificates of my own choice A processor fast enough to run Quake 3! =)

  Read the article

• Is there any way to tweak / rotate mouse orientation? Any applications? Registry edits?

  - by calbar

  I've got a very frustrating issue with my new Logitech Marathon Mouse M705. It is absolutely perfect for what I need, with the exception that it tracks on an angle for some reason. What I mean is when you slide the cursor to the left, it trends upward - when you slide to the right, it trends down. Moving the cursor along a flat horizontal line is no longer a natural motion - you need to fight what I suspect is a mechanical error of some kind. Unfortunately, I've already exchanged this mouse once and tested both on different Windows 7 and Mac OS X machines - the problem continues to occur. Is there a software solution for me? I'm incredibly surprised there is no simple way to adjust the orientation... how can every mouse manufacturer possibly adjust their hardware to track to everyone's tastes? What about those who need to flip orientation a full 90 or 180 degrees? I only need to adjust mine a few degrees, but I'm sure that need has arisen as well. Anyway, I'm running the latest SetPoint drivers (6.00) on Windows 7 and there are no orientation options available. I've checked out uberOptions and the M705 isn't supported yet (with the last version update over 6 months ago). MAF Mouse instructions are a very strange series of mouse clicks to activate. This app also seems a little overkill and costs $$ (which I'm willing to pay as a last resort). Is there no universal registry value for mouse orientation? How about for SetPoint drivers specifically? I've done a simple search in regedit without any luck. An XML file somewhere? Anything?

  Read the article

• In APC+PHP, how much RAM is too much? Is it okay to set apc.shm_size to many GB?

  - by Jeremy Clarke

  On our server we have a LOT of RAM for our traffic levels (16GB). The HTTP processes regularly eat up all CPU and need to be restarted without even getting close to using swap memory, so I'm looking for ways to spend RAM to ease the load on Apache (and/or help the seperate MySQL server which may be breaking Apache). I have many WordPress installs on the HTTPD instance so APC sometimes uses as much as 900MB of ram (according to the apc.php charts). Just in case I have apc.shm_size set to 1600MB which is more than it needs but not more than I can spare. This means there is usually lots of extra RAM available to APC but also very little turnover and fragmentation is never more than 1%. Is this dangerous? Should I be slimming down APC to less than 1GB just on principle? Should I be expecting some turnover within APC in the name of bringing it's overall footprint down? Having so much memory devoted to APC means that in top/htop every single httpd process shows ~1.9GB in the VIRT memory column. Obviously this is shared memory and not used per-process, but could it be hurting our server? NOTE: The problem with the server remains unclear but the effect is that about 60 times a day all 8 CPU's fill up to 100% and everything stops working until Monit sees that Apache is broken and restarts it (Monin also saves the MySQL server). I'm not sure if APC is even part of the problem but I'm trying to optimize everything just in case.

  Read the article

• How to go about rotating logs which are arbitrary named and placed in deeply nested directories?

  - by Roman Grazhdan

  I have a couple of hosts which are basically a playground for developers. On these hosts, each of them has a directory under /tmp where he is free to do all he wants - store files, write logs etc. Of course, the logs are to be rotated, or else the disc will be 100% full in a week. The files can be plenty, but I've dealt with it with paths like /tmp/[a-e]*/* and so on and lived happily for a while, but as they try new cool stuff on the machine logrotate rules grow ugly and unmanageable, and it's getting more difficult to understand which files hit the glob. Also, logrotate would segfault if asked to rotate a socket. I don't feel like trying to enforce some naming policies in that environment, I think it's going to take quite a lot of time and get people annoyed and still would fail at some point. And I still need to manage the logs, not just rm the dirs at night. So is it a good idea in circumstances like these to write a script which would handle these temporary files? I prefer sticking with standard utilities whenever possible, but here I think logrotate is getting less and less manageable. And probably someone heard of some logrotate alternatives which would work well in such an environment? I don't need emailing logs or some other advanced features, so theoretically some well commented find | xargs would do. P.S. I do have a log aggregator but this stuff is not going to touch my little cute logstash machine.

  Read the article

< Previous Page | 351 352 353 354 355 356 357 358 359 360 361 362  | Next Page >