Search Results

Search found 12281 results on 492 pages for 'ip blocking'.

Page 357/492 | < Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >

• Is there a way to submit a batch of commands to a Cisco router and have them execute from the router?

  - by atroon

  I need to change the configuration of a remote (6 hours' drive) client's Cisco 871 (IOS 12.4.15T) from my location because of some new internet service at his location. To be more precise, I need to change the default route, ip address of the outside interface (Fa4) and disable the PPPoE setup there. Unfortunately, doing any of this will (obviously) break the connection to the router. I do not have an out-of-band management modem set up (I know, I know). Is there any way to enter the commands I need to have run and have them execute one after the other, from a file on flash:? I have never tried anything like that before. Essentially a DOS-style batch file is exactly what I need. Nothing like it seems to be out there except using kron to execute CLI commands, but that is specified here as only taking EXEC commands, not configuration ones. Is there hope, or do I travel?

  Read the article

• Debugging Connection Issues Between Two Linux Servers

  - by clickfault

  I have two CentOS 5 servers running iptables and apf. I am having issues connecting with ssh from server 1 to server 2. I can connect from server 1 to a third server and from that third server to both 1 and 2. In all cases I am using the IP address and not a host name. I have stopped iptables and apf on all servers and it doesn't seem to change anything. What is the best way to debug this process?

  Read the article

• How to route traffic through a specific SOCKS proxy on a per-app basis?

  - by GJ.

  I'm running a certain desktop app (actually via AIR if it makes any difference) which doesn't have any built-in proxy configuration settings. I need to get all traffic just from this app directed through a secure SOCKS proxy. This implies I can't use the global network preferences, as these would affect many other apps. Is there any way to force all network communication through a given SOCKS proxy on a per-app basis? It would also be helpful to know if there's a way to perform such routing globally, based on specific IP addresses (as this could allow for some reasonable workaround).

  Read the article

• How to detect when a user copies files from a server over the network?

  - by Mr. Graves

  I have a few virtual servers + desktops that are used for shared development with remote users, including some consultants. Each user has an account with access to most aspects of the server. I don't want to prevent people from being productive, or track passwords or read emails, but I do want to know when and what files they copy from the virtual server or what they upload from the server to a remote site, and what if any applications they install. This will help make sure my IP is protected, that no one is installing tools they shouldn't, and that things are licensed appropriately. What is the simplest way to do this? In order of importance I would say detecting file transfers off the machine to be most critical. Thanks

  Read the article

• Routing table change to access Internet over mifi

  - by Randall Blake

  I have two networks at home. One uses a Verizon mifi wireless on 192.168.1.1. The other uses a dlink router on 192.168.0.1. I have one laptop with two nics, one wireless and one not. The wireless nic connects to the mifi. The Ethernet nic connects to the dlink router. It's ip is 192.168.0.2. I also have a laptop with only one nic connected to the dlink on 192.168.0.3. I want to connect laptop 2 to the Internet. Can I do that by adding an entry to the routing table so that destination 0.0.0.0 routes to 192.168.0.2? If I do that, will laptop 1 "know" that it should route traffic from 192.168.0.3 to 192.168.1.1? Thanks for any assistance.

  Read the article

• open-iscsi does not login into targets on boot

  - by Creshal

  We have a Debian Lenny server with open-iscsi that's configured to log into a target automatically: hostname:~# grep \\.startup /etc/iscsi/iscsid.conf node.startup = automatic hostname:~# grep \\.startup /etc/iscsi/nodes/iqn..../the.correct.ip.address\,port node.startup = automatic node.conn[0].startup = automatic hostname:~# If I issue a restart of open-iscsi via init.d, it works fine. But if I reboot the machine, iscsi starts, but does not even search for targets. I have to manually restart it before it works. Any ideas how to make it find the target on boot?

  Read the article

• How to correctly set up iWARP? Preferably on loopback

  - by ajdecon

  iWARP is a protocol for doing remote direct memory access (RDMA) on top of TCP/IP, so that it can work with Ethernet and other network types as opposed to Infiniband. It works with many of the standard IB interfaces - the IB verbs, for example - so it's all pretty transparent. I'm doing some IB-verbs programming (mostly for the sake of learning about how they work better), and it'd be wonderfully convenient for me if I could use iWARP to do RDMA over my loopback interface, so that I could test some of my code without getting on our IB-connected cluster. :-) But I cannot figure out how to get a "local development environment" set up: there are no tutorials I'm aware of for even setting up iWARP from scratch on a server or a network interface. Can anyone give me a tutorial or point me in the right direction? Environment is Fedora 16 running in VirtualBox.

  Read the article

• How to upgrade a single instance's size without downtime

  - by Justin Meltzer

  I'm afraid there may not be a way to do this since we're not load balancing, but I'd like to know if there is any way to upgrade an EC2 EBS backed instance to a larger size without downtime. First of all, we have everything on one instance: both our app and our database (mongodb). This is along the lines i'm thinking: I know you can create snapshots of your EBS and an AMI of your instance. We already have an AMI and we create hourly snapshots. If I spin up a new separate instance of a larger size and then implement (not sure what the right term is here) the snapshots so that our database is up to date, then I could switch the A record of our domain from the old ip address to the new one. However, I'm afraid that after copying over the data from the snapshot, by the time it takes to change the A record and have that change propagate, the data could potentially be stale. Is there a way to prevent this, and is there a better way to do this than I am suggesting?

  Read the article

• Configuring BIND to use VM's DNS for specific domain

  - by Srirangan

  I work on a project for which I use an Ubuntu server vm on an Ubuntu host. The VM runs all the services / webapps through haproxy and nginx and serves it on the domain (xyz.com). I manually modify my resolv.conf to use the VMs IP address as the nameserver and I can run my app on the host browser. The problem is I am modifying an auto-generated file (resolv.conf) and I need to do it each time. Is there a smart way to say: -- are you accessing xyz.com? -- if yes use VM's DNS server, else use the hosts

  Read the article

• Finding the most common errors in event logs using Powershell.

  - by Paul

  I have the event logs for one of our servers locally in .evtx format. I can load the log file into PS using the command: Get-WinEvent -Path D:\Desktop\serverlogs.evtx What I would like to do is on the Message field group events where the text matches by a certain percent (say 80% the same). As we have stacktraces for errors in the details which will be the same, but we also log the client's IP, url that was accessed which will likely be different. I want to group them so that I can work out the most common errors to prioritize fixing them and as there are 25,000+ errors in the log file I would rather not do it manually. I think I can work out how to do most of this, but am not sure how I could do the 'group fields which are mostly the same' part, does powershell have anything like this built in?

  Read the article

• Where is debian storing its network settings?

  - by user13743

  I have a debian machine that is supposed to have a static ip, but insists on getting its address from the DHCP server. Here's this settings file: $> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.1.99 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 Yet $> sudo /etc/init.d/networking restart Reconfiguring network interfaces...done. $> sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:e0:03:09:05:2e inet addr:192.168.1.205 Bcast:255.255.255.255 Mask:255.255.255.0 ... Where is it being told to use dhcp?

  Read the article

• postfix and chdir domain.com/admin/ failed

  - by senzacionale

  root@ubuntu-server:/var/log# telnet localhost 110 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. +OK Hello there. user [email protected] +OK Password required. pass MyPasswd -ERR chdir domain.com/admin/ failed Connection closed by foreign host. and mail.log Apr 24 12:36:41 ubuntu-server pop3d: Connection, ip=[::ffff:127.0.0.1] Apr 24 12:36:58 ubuntu-server pop3d: chdir domain.com/admin/: No such file or directory what can i do? how to set up this directories? MX records are set, domain is set,...

  Read the article

• Apache Configuration Issue - website without www going to default site

  - by Brian

  I have included a copy of my virtual host file for apache below. (However I have hidden the ip address and domain name for now) My problem is that the following work: www.mydomainnamehere.org www.mydomainnamehere.com mydomainnamehere.com This one doesn't work: mydomainnamehere.org - instead of going to the document root listed below, it goes to the document root of the default site. What could be causing this? <VirtualHost [ipaddresshidden]:80> ServerAdmin [email protected] ServerName mydomainnamehere.org ServerAlias www.mydomainnamehere.org ServerAlias mydomainnamehere.com ServerAlias www.mydomainnamehere.com DocumentRoot /home/www/mydomainnamehere.org/html/ ErrorLog /home/www/mydomainnamehere.org/logs/error.log CustomLog /home/www/mydomainnamehere.org/logs/access.log combined </VirtualHost>

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• network user isolation

  - by seaquest

  My question is for a network with a Linux iptables router gateway. How can it be possible to prevent inter-network traffic of those users. Think this case as a public network, IPs are distributed through linux gw and users are authenticated thru the gateway. We want to protect public users from public users. Network is not wireless and I can not use Wireless AP user isolation. Actually I have a simple method. Subnet the network into /30 mask. Give minimum IP of each subnet to the gateay and ditribute those /30 IPs from the subnet. But this is pretty costly for such an aim. I want to ask for other methods Thanks.

  Read the article

• VLC RTP Streaming in FC12

  - by Matt D

  I'm trying to get VLC to work streaming RTP audio/video over my office network. The goal is multicast a/v streaming. In all test cases, we are streaming from VLC to VLC. I am able to stream from Windows to Windows, and from Fedora to Windows, but not from Windows to Fedora. Additionally, I am unable to receive a LOCAL stream from one instance of VLC to another, within Fedora. I don't see any reason why this would be. The buffer indicator (where the elapsed/total time is normally displayed) never shows any connectivity, so it would appear to be a network problem, but since I am able to stream from Fedora to Windows (same IP, same port) I thought it would be something else. Does anyone know of a solution to this issue?

  Read the article

• Machine account authentication on Radius server

  - by O.Shevchenko

  My workstation is under Linux. I have an Active Directory domain controller + Radius server on Windows 2008. I can verify user account 'radius-01' using 'radtest' tool: $ radtest -t pap radius-01 password123 195.234.133.32 1812 password123 Sending Access-Request of id 98 to 195.234.73.2 port 1812 User-Name = "radius-01" User-Password = "password123" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 rad_recv: Access-Accept packet from host 195.234.133.32 port 1812, id=98, length=84 Framed-MTU = 1344 Framed-Protocol = PPP Service-Type = Framed-User Class = 0x537004f00000013700010200ac1c0... I have joined my Linux PC to Active Directory domain ARB-HRK using Samba: [root@shev-arb]# net ads testjoin Join is OK I can dump machine password: [root@shev-arb]# tdbdump /var/lib/samba/private/secrets.tdb { key(34) = "SECRETS/MACHINE_PASSWORD/ARB-HRK" data(15) = "yGgXJsquRnpT0g\00" } How can i authenticate my machine account on Radius server? Do anybody know any tools for this, like: radtest shev-arb$ yGgXJsquRnpT0g 195.234.133.32 1812 password123 (this command fails)

  Read the article

• Removing (Presumably) Extraneous Network Adapters from Device Manager (eg WAN Miniport)

  - by Synetech inc.

  Can anyone shed some light on the default items in the Network Adapters branch of the Windows Device Manager? In addition to the network card, there are always a bunch of other things that I cannot find any useful information on such as RAS Asynch Adapter and all the WAN Miniports (IKEv2, IP(v6), L2TP, Network Monitor, PPPOE, PPTP, SSTP). I would like to trim it down and uninstall whatever possible but cannot find out exactly what these items are responsible for (and therefore whether or not they are needed on my system). Most of the pages found with Google are either people trying to fix an error with such an item or someone asking what it is and being given an unhelpful, pat response like “just leave them alone” or “they’re necessary”. I highly doubt that is the case and I’m certain that at least some items can be removed because even if they become necessary in the future they can be added again (for example installing Network Monitor or Protowall reinstalls the miniport drivers anyway).

  Read the article

• Timeouts when connecting to SQL Server since installing SP1 for Windows 7

  - by Julien

  Hi, I just installed SP1 for windows 7 and I have severe performance degradation when connecting to SQL Server 2005 since then. Establishing connection takes more than 30 seconds while it's instantaneous on another computer. Firewall is disabled and I didn't make any change to the configuration. It happens both when trying to connect with a hostname and with an ip address. Everything else seems to be fine (for instance, I'm have no issue connecting to other computers with remote desktop) What can cause such a problem? Thanks in advance! Edit : uninstalling the SP1 solves the issue instantly.

  Read the article

• VoIP on Netgear DGN 2000 and Lynksys PAP2

  - by David Brown

  I have a VoIP service running perfectly for outgoing calls but I cannot receive incoming calls. I have a Netgear DGN 2000 modem router on 192.168.0.1 and a Lynksys Phone Adapter PAP2 on 192.168.0.2. I have created 3 new custom services: Service Table Service Name Ports tlenfon(TCP) 5060 tlenfon2(UDP) 15000 tlenfon3(UDP) 35000 I have reserved the address 192.168.0.2 for the PAP 2 I have forwarded the ports for each service to the PAP2 Service Name Action LAN Server IP address WAN Users Log tlenfon ALLOW always 192.168.0.2 Any Always tlenfon2 ALLOW always 192.168.0.2 Any Always tlenfon3 ALLOW always 192.168.0.2 Any Always I have checked the Default DMZ and specified 192.168.0.2 What have I missed?

  Read the article

• Do I need a VPN to secure communication over a T1 line?

  - by Seth

  I have a dedicated T1 line that runs between my office and my data center. Both ends have public IP addresses. On both ends, we have a T1 routers which connect to SonicWall firewalls. The SonicWalls do a site-to-site VPN and handle the network translation, so the computers on the office network (10.0.100.x) can access the servers in the rack (10.0.103.x). So the question: can I just add a static route to the SonicWalls so each network can access each other with out the VPN? Are there security problems (such as, someone else adding the appropriate static route and being able to access either the office or the datacenter)? Is there another / better way to do it? The reason I'm looking at this is because the T1 is already a pretty small pipe, and having the VPN overhead makes connectivity really slow.

  Read the article

• "DNS not responding" error with D-Link router and PPTP internet connection

  - by Born2win

  I have a D-Link DIR-615 router since around six months. My internet connection is VPN (PPTP) based, i.e. I have been given a username and password from my ISP and my IP address is dynamic. Since a few days I am experiencing a serious problem. My router connects normally (I can see the yellow light), but my computer is giving me a "DNS not responding" error. I have tried everything (reset, reboot etc.) but no success.

  Read the article

• iptables and snatting to different networks

  - by codingfreak

  linuxbox (p.q.r.t) | | INTERNAL ------ ABCD ----- INTERNET (p.q.r.s) (m.n.o.k) ABCD has 3 interfaces connected to linuxbox, INTERNAL N/W, INTERNET. Linuxbox has a private address (p.q.r.t). At present I am snatting the packets from linuxbox to INTERNET at ABCD. I have a small doubt regarding the FTP from linuxbox since I have to support ftp from linuxbox to both INTERNAL N/W as well as in INTERNET. How can I right a rule in iptables present in ABCD where it can decide if the destination ip-address of ftp server is within INTERNAL N/W or in INTERNET and do natting accordingly.

  Read the article

• How to configure machines in a public subnet with two gateways?

  - by Shtééf

  We have a single public /24 subnet, with a BGP router as the primary gateway. Now I'm interested in configuring a second router for redundancy. How do I deal with multiple gateways on the servers in our public subnet? I found some other questions related to multiple gateways that seem to deal with NAT set-ups. In my situation, the servers all have public routed IP-addresses. So from what I can tell, it doesn't really matter which route incoming or outgoing packets take. But I figure the servers need some way of telling when one of the gateways is down, and route around it? Is this accomplished with protocols such as OSPF? And do I need to deploy this on all my servers?

  Read the article

• Virtual hosting all resolving to the same files

  - by nona urbiz

  I'm trying to set up virtual hosts on my VPS (centos). I set both domain nameservers to fns1.dnspark.net and fns2.dnspark.net and set an A record there for each domain pointing to my IP address 50.16.219.8. Both domains are currently resolving to the first virtual host. What am I doing wrong? Thanks! NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/root/dylanstestserver.com ServerName dylanstestserver.com ServerAlias www.dylanstestserver.com ErrorLog logs/dylanstestserver.com-error-log CustomLog logs/dylanstestserver.com-access_log common </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/root/repthis.info ServerName repthis.info ServerAlias www.repthis.info ErrorLog logs/repthis.info-error-log CustomLog logs/repthis.info-access_log common </VirtualHost>

  Read the article

< Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >