Search Results

Search found 34306 results on 1373 pages for 'ubuntu 14 04'.

Page 357/1373 | < Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >

• Installing Linux on an Asus p8z68-m PRO Motherboard

  - by Holland

  Here is a challenge: how is this done? I've tried disabling the ASM1061 controller in the Onboard Devices section, using Wubi, booting from USB (as I don't have a DVD drive, yet), and even booting from RAID/IDE (with AHCI as the default) to do this. Still, no dice. Google shows up virtually nothing related about Linux and this mobo, apart from a people just saying "disable ASMedia" (which, I assume is the ASM1061 controller, as that's all I see - apart from the USB 3.0, which I disabled already) and it hasn't really helped much. Thus, what is wrong here? Edit My problem is that I cannot boot Linux via USB or a simple Windows installer such as Wubi (for Ubuntu). I wind up getting error messages along the lines of write cache failed, along with many other cryptic error messages similar to the following: [ 1400.351374] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled [ 1400.353433] sd 4:0:0:0: [sdb] Asking for cache data failed [ 1400.356601] sd 4:0:0:0: [sdb] Assuming drive cache: write through This seems to be common for Asus P8Z68-M Pro motherboards, with the only notable solution being to "disable ASMedia", which, as I said before, I'm guessing is the ASM1061 controller on the motherboard. Despite already disabling this, I have tried this with both Fedora and Ubuntu without any success. I need to know what I can do about this; has anyone ran into something similar or heard about this issue before? I know these motherboards are relatively new...

  Read the article

• Memcached Lagging

  - by Brad Dwyer

  Let me preface this by saying that this is a followup question to this topic. That was "solved" by switching from Solaris (SmartOS) to Ubuntu for the memcached server. Now we've multiplied load by about 5x and are running into problems again. We are running a site that is doing about 1000 requests/minute, each request hits Memcached with approximately 3 reads and 1 write. So load is approximately 65 requests per second. Total data in the cache is about 37M, and each key contains a very small amount of data (a JSON-encoded array of integers amounting to less than 1K). We have setup a benchmarking script on these pages and fed the data into StatsD for logging. The problem is that there are spikes where Memcached takes a very long time to respond. These do not appear to correlate with spikes in traffic. What could be causing these spikes? Why would memcached take over a second to reply? We just booted up a second server to put in the pool and it didn't make any noticeable difference in the frequency or severity of the spikes. This is the output of getStats() on the servers: Array ( [-----------] => Array ( [pid] => 1364 [uptime] => 3715684 [threads] => 4 [time] => 1336596719 [pointer_size] => 64 [rusage_user_seconds] => 7924 [rusage_user_microseconds] => 170000 [rusage_system_seconds] => 187214 [rusage_system_microseconds] => 190000 [curr_items] => 12578 [total_items] => 53516300 [limit_maxbytes] => 943718400 [curr_connections] => 14 [total_connections] => 72550117 [connection_structures] => 165 [bytes] => 2616068 [cmd_get] => 450388258 [cmd_set] => 53493365 [get_hits] => 450388258 [get_misses] => 2244297 [evictions] => 0 [bytes_read] => 2138744916 [bytes_written] => 745275216 [version] => 1.4.2 ) [-----------:11211] => Array ( [pid] => 8099 [uptime] => 4687 [threads] => 4 [time] => 1336596719 [pointer_size] => 64 [rusage_user_seconds] => 7 [rusage_user_microseconds] => 170000 [rusage_system_seconds] => 290 [rusage_system_microseconds] => 990000 [curr_items] => 2384 [total_items] => 225964 [limit_maxbytes] => 943718400 [curr_connections] => 7 [total_connections] => 588097 [connection_structures] => 91 [bytes] => 562641 [cmd_get] => 1012562 [cmd_set] => 225778 [get_hits] => 1012562 [get_misses] => 125161 [evictions] => 0 [bytes_read] => 91270698 [bytes_written] => 350071516 [version] => 1.4.2 ) ) Edit: Here is the result of a set and retrieve of 10,000 values. Normal: Stored 10000 values in 5.6118 seconds. Average: 0.0006 High: 0.1958 Low: 0.0003 Fetched 10000 values in 5.1215 seconds. Average: 0.0005 High: 0.0141 Low: 0.0003 When Spiking: Stored 10000 values in 16.5074 seconds. Average: 0.0017 High: 0.9288 Low: 0.0003 Fetched 10000 values in 19.8771 seconds. Average: 0.0020 High: 0.9478 Low: 0.0003

  Read the article

• BIOS corrupted? How to proceed? Acer Travelmate 290

  - by dtlussier

  I have a older ACER Travelmate 290 (manufactured in 2002 or 2003), which I recently tried to upgrade to Ubuntu 9.10. After doing the upgrade process it appeared as if I had a problem with my x server configuration, as on the first reboot post-install I heard the Ubuntu startup sound, but had a black screen. I thought I would then reboot again to drop down into text-mode to trouble shoot the x configuration problem. However, when I tried rebooting, something went wrong and since then when I start up the machine I get absolutely nothing except the first hardware check (i.e. HDD light flashes, CD/DVD drive spins, etc.). Other than that the screen remains totally black and I have no HDD or processor activity at all. I have tried restarting it a number of time holding down all kinds of key combinations to try and coax it into the BIOS (if possible) with no luck. I have also tried putting in both a live Linux disc and a Windows install disk without any luck. With a disk in the drive it will spin for a few seconds and then stop. All this has lead me to suspect that the BIOS is somehow corrupt (not sure about the right terminology). I have tried putting a new BIOS image and installer program downloaded from ACER on a USB key to see if it will run when I start up the machine, but no luck. I'm not sure if this method of interacting/updating/flashing the BIOS will work outside of Windows/DOS as both OSs are mentioned kind of ambiguously in the documentation. I have also taken the laptop case apart and inspected the various cards and cannot find any obviously burned out components. I'm not sure how to proceed at this point in terms of components to try, or how to try and load a new BIOS image onto the board. Any advice here would be great, especially from those with experience with this particular line of laptops. Thanks!

  Read the article

• Samba4 [homes] share

  - by SambaDrivesMeCrazy

  I am having issues with the [homes] share. OS is Ubuntu 12.04. I've installed samba 4.0.3, bind9 dlz, ntp, winbind, everything but pam modules, and did all the tests from https://wiki.samba.org/index.php/Samba_AD_DC_HOWTO. Running getent passwd and getent user work just fine. Creating a simple share works just fine too. I can manage the users, GPOs, and DNS from the windows mmc snap-ins. I can join winxp,7,8 to the domain and log on perfectly. I can change my passwords from windows, etc..etc.. I could say that everything is fine and be happy :) buuuut, no, home directories do not work. Searching in here, and on our good friend google I gathered that a simple [homes] read only = no path = /storage-server/users/ and mapping the user's home folder in dsa.msc to \\server-001\username or \\server-001\homes should get me a home share I could map for my user homedir. But the snap-in give me an error saying that it cannot create the home folder because the network name has not been found (rough translation from portuguese). also, running root@server-001:/storage-server/users# smbclient //server-001/test -Utest%'12345678' -c 'ls' Domain=[MYDOMAIN] OS=[Unix] Server=[Samba 4.0.3] tree connect failed: NT_STATUS_BAD_NETWORK_NAME Server name is alright, if I go for a simple share on the same server it opens just fine. If I map the user homedir to this simple share it works. What I want is that I dont have to go and manually make a new folder on linux everytime I create a new user on windows. It looks like permissions but I cant find any documentation on this (yes I've tried the manpages, but its hard to tell with so many options on man smb.conf alone). My smb.conf right now looks like this (pretty simple I know) # Global parameters [global] workgroup = MYDOMAIN realm = MYDOMAIN.LAN netbios name = SERVER-001 server role = active directory domain controller server services = s3fs, rpc, nbt, wrepl, ldap, cldap, kdc, drepl, winbind, ntp_signd, kcc, dnsupdate [netlogon] path = /usr/local/samba/var/locks/sysvol/mydomain.lan/scripts read only = No [sysvol] path = /usr/local/samba/var/locks/sysvol read only = No [homes] read only = no path = /storage-server/users Folder permissions /storage-server drwxr-xr-x 6 root root 4096 Fev 15 15:17 storage-server /storage-server/users drwxrwxrwx 6 root root 4096 Fev 18 17:05 users/ Yes, I was desperate enough to set 777 on the users folder... not proud of it. Any pointers in the right direction would be very welcome. Edited to include: root@server-001:/# wbinfo --user-info=test MYDOMAIN\test:*:3000045:100:test:/home/MYDOMAIN/test:/bin/false root@server-001:/# wbinfo -n test S-1-5-21-1957592451-3401938807-633234758-1128 SID_USER (1) root@server-001:/# id test uid=3000045(MYDOMAIN\test) gid=100(users) grupos=100(users) root@server-001:/# wbinfo -U 3000045 S-1-5-21-1957592451-3401938807-633234758-1128 root@server-001:/# Edit 2: getent passwd | grep test MYDOMAIN\test:*:3000045:100:test:/home/MYDOMAIN/test:/bin/false I have no idea how to change that home folder to /storage-server/users/test so I just went and ln -s /storage-server/users /home/MYDOMAIN just in case. still, no changes, same errors. Edit 3 On log.smbd I get the following error when trying to set the test user home folder to \server-001\test [2013/02/20 14:22:08.446658, 2] ../source3/smbd/service.c:418(create_connection_session_info) user 'MYDOMAIN\Administrator' (from session setup) not permitted to access this share (test)

  Read the article

• iconv supports too few encoding

  - by schemacs

  iconv -l outputs too few encodings on CentOS 6.5: $ iconv -l 10646-1:1993, 10646-1:1993/UCS4, ANSI_X3.4-1968, ANSI_X3.4-1986, ANSI_X3.4, ASCII, CP367, CSASCII, CSUCS4, IBM367, ISO-10646, ISO-10646/UCS2, ISO-10646/UCS4, ISO-10646/UTF-8, ISO-10646/UTF8, ISO-IR-6, ISO-IR-193, ISO646-US, ISO_646.IRV:1991, OSF00010020, OSF00010100, OSF00010101, OSF00010102, OSF00010104, OSF00010105, OSF00010106, OSF05010001, UCS-2, UCS-2BE, UCS-2LE, UCS-4, UCS-4BE, UCS-4LE, UCS2, UCS4, UNICODEBIG, UNICODELITTLE, US-ASCII, US, UTF-8, UTF8, WCHAR_T But on my Ubuntu the list seems much longer, here is different: CentOS6.5: $ php -a php > echo iconv('utf8', 'gbk', 'abc'); PHP Notice: iconv(): Wrong charset, conversion from `utf8' to `gbk' is not allowed in php shell code on line 1 php > quit $ php -i|grep iconv iconv iconv support => enabled iconv implementation => glibc iconv library version => 2.12 iconv.input_encoding => ISO-8859-1 => ISO-8859-1 iconv.internal_encoding => ISO-8859-1 => ISO-8859-1 iconv.output_encoding => ISO-8859-1 => ISO-8859-1 Ubuntu 14.04: $ php -a Interactive mode enabled php > echo iconv('utf8', 'gbk', "abc\n"); abc php > quit $ php -i|grep iconv iconv iconv support => enabled iconv implementation => glibc iconv library version => 2.19 iconv.input_encoding => ISO-8859-1 => ISO-8859-1 iconv.internal_encoding => ISO-8859-1 => ISO-8859-1 iconv.output_encoding => ISO-8859-1 => ISO-8859-1 But I don't want to recompile glibc(this will be huge mount of work), any idea on how to ad new encoding support?

  Read the article

• ghc6 install trouble: hGetContents: invalid argument (invalid UTF-8 byte sequence)

  - by olimay

  Having trouble installing ghc6 on Ubuntu Maverick via apt. Here's what seems to be the relevant error that comes up when I try to (apt-get|aptitude) install ghc6: A package failed to install. Trying to recover: Setting up ghc6 (6.12.1-13ubuntu1) ... ghc-pkg: /home/opm/.ghc/i386-linux-6.12.1/package.conf.d/unix-compat-0.2-edefa7bced91ebe610d455bab466e200.conf: hGetContents: invalid argument (invalid UTF-8 byte sequence) (Here's the full output, if you're interested: http://paste.ubuntu.com/566475/ ) This still happens after apt-get clean and apt-get update. My searching around has not really helped me understand what's going on, except that it might be caused by a mismatch in locale. So, here's the output of locale too: LANG=en_US.utf8 LANGUAGE=en_US:en LC_CTYPE="en_US.utf8" LC_NUMERIC="en_US.utf8" LC_TIME="en_US.utf8" LC_COLLATE="en_US.utf8" LC_MONETARY="en_US.utf8" LC_MESSAGES="en_US.utf8" LC_PAPER="en_US.utf8" LC_NAME="en_US.utf8" LC_ADDRESS="en_US.utf8" LC_TELEPHONE="en_US.utf8" LC_MEASUREMENT="en_US.utf8" LC_IDENTIFICATION="en_US.utf8" LC_ALL= Any ideas? Additional background: this all seems very strange to me, because I used to have ghc6 installed correctly--I use XMonad as my main window manager most of the time. I tried to install haskell-platform (through apt), which failed and told me that there was something wrong with ghc6, and so I reinstalled ghc6 and began to get the above error message.

  Read the article

• Cannot send email outside of network using Postfix

  - by infmz

  I've set up an Ubuntu server with Request Tracker following this guide (the section about inbound mail would be relevant). However, while I'm able to send mail to other users within the network/domain, I cannot seem to reach beyond - such as my personal accounts etc. Now I have no idea what is causing this, I thought that all it takes is for the system to fetch mail through our exchange server and be able to deliver in the same way. However, that hasn't been the case. I have found another server setup in a similar fashion (CentOS 5, Request Tracker but using Sendmail), however it is a dated server and whoever's built it has kindly left no documentation on how it works, making it a pain to use that as a reference system! :) At one point, I was told I need to set up a relay between the local server's email add and our AD server but this didn't seem to work. Sorry, I know next to nothing about mailservers, my colleagues nothing about Linux so it's a hard one for me. Thank you! EDIT: Result of postconf -N with details masked =) alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = myhost.mydomain.com, localhost.mydomain.com, , localhost myhostname = myhost.mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = EXCHANGE IP smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes Sample log message: Sep 4 12:32:05 theedgesupport postfix/smtp[9152]: 2147B200B99: to=<[email protected]>, relay= RELAY IP :25, delay=0.1, delays=0.05/0/0/0.04, dsn=5.7.1, status=bounced (host HOST IP said: 550 5.7.1 Unable to relay for [email protected] (in reply to RCPT TO command))

  Read the article

• Easy Linux distribution with newer packages than Ubuntu?

  - by sweetiecakes

  I'm a programmer and sysadmin, and I'm looking for a better Linux distro to use than Ubuntu. It certainly is a well-polished, nice distribution to use, but a lot of the programs available in the Ubuntu repositories are very old versions. Installing PPA's or compiling from source just isn't very nice. I'd love to use something like Arch Linux that uses a rolling release cycle, but I really don't want to configure my system from scratch, and support for ATI Catalyst drivers is necessary. I just want to pop the CD in, install and start using my computer - just like with Ubuntu. Additionally, if you know of a package like ubuntu-restricted-extras for the distribution, that'd be nice! What do you suggest?

  Read the article

• Passwordless SSH not working - keys copied and permissions set

  - by Comcar

  I know this question has been asked, but I'm certain I've done what all the other answers suggest. Machine A: used keygen -t rsa to create id_rsa.pub in ~/.ssh/ copied Machine A's id_rsa.pub to Machine B user's home directory Made the file permissions of id_rsa.pub 600 Machine B added Machine A's pub key to authorised_keys and authorised_keys2: cat ~/id_rsa.pub ~/.ssh/authorised_keys2 made the file permissions of id_rsa.pub 600 I've also ensured both the .ssh directories have the permission 700 on both machine A and B. If I try to login to machine B from machine A, I get asked for the password, not the ssh pass phrase. I've got the root users on both machines to talk to each other using password-less ssh, but I can't get a normal user to do it. Do the user names have to be the same on both sides? Or is there some setting else where I've missed. Machine A is a Ubuntu 10.04 virtual machine running inside VirtualBox on a Windows 7 PC, Machine B is a dedicated Ubuntu 9.10 server UPDATE : I've run ssh with the option -vvv, which provides many many lines of output, but this is the last few commands: debug3: check_host_in_hostfile: filename /home/pete/.ssh/known_hosts debug3: check_host_in_hostfile: match line 1 debug1: Host '192.168.1.19' is known and matches the RSA host key. debug1: Found key in /home/pete/.ssh/known_hosts:1 debug2: bits set: 504/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/pete/.ssh/identity ((nil)) debug2: key: /home/pete/.ssh/id_rsa (0x7ffe1baab9d0) debug2: key: /home/pete/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127 debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/pete/.ssh/identity debug3: no such identity: /home/pete/.ssh/identity debug1: Offering public key: /home/pete/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/pete/.ssh/id_dsa debug3: no such identity: /home/pete/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password

  Read the article

• lm-sensors - always returns 32 degrees (celsius) for temperature

  - by mopoke

  On my VIA EPIA motherboard (using VIA VT8231 ISA bridge), I get strange output for the lm-sensors temperature reading. It always returns 32 degrees (celsius). I have previously had correct output for temperature (my munin graphs show temperatures typically in the range of 50 to 60 degrees. I've tried uninstalling (and purging) the lm-sensors package, have re-run sensors-detect a number of times and rebooted but nothing seems to change the output. I am running Ubuntu Karmic Koala (9.10). Anyone got any bright ideas on what I might have missed? uname -a: Linux george 2.6.31-16-386 #53-Ubuntu SMP Tue Dec 8 06:39:34 UTC 2009 i686 GNU/Linux cpuinfo: processor : 0 vendor_id : CentaurHauls cpu family : 6 model : 7 model name : VIA Samuel 2 stepping : 3 cpu MHz : 399.000 cache size : 64 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu de tsc msr cx8 mtrr pge mmx 3dnow up bogomips : 800.04 clflush size : 32 power management: lspci: 00:00.0 Host bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia] (rev 05) 00:01.0 PCI bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia AGP] 00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev 10) 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e) 00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e) 00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10) 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40) 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 51) 01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 6a) sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +32.0°C (crit = +60.0°C)

  Read the article

• Recovering Data from a Linkstation LS-WXL/R1

  - by kingkool68

  I've been running a Buffalo Linkstation LS-WXL/R1 in RAID1 for a few weeks. Two nights ago we had a brief power outage. Yesterday when I tried to mount the disk it couldn't be found. I logged in to the web admin and it couldn't see any storage attached and no arrays available. Well this sucks. I ended up taking the disks out and mounting them to an Ubuntu virtual machine. They how up as an Array but I can't start the Array to the best of my limited knowledge. I could still see the 6 partitions, so I'm confident the data is there. I can use Photorec (http://www.cgsecurity.org/wiki/PhotoRec) to recover most of the files I want, it just takes some time. Could I make an image of the data partition and mount that in Ubuntu so I can get at the data I want through the file system? 95% of the data on my Linkstation LS-WXL/R1 is backup. I just put a few folders of images on there that I need to get back. I'm already preparing to format the disks when I'm done and re-building the RAID1 array from scratch. Any advice would be appreciated.

  Read the article

• Recover LVM2 volume group after one HDD failed

  - by Bernd

  I had two HDDs, each one containing a LVM partition which formed a volume group. Then I had two LVs, one for my / directory and one for my /home/ directory. Yesterday where I had my / dir failed. I'm trying to recover at least my /home/ dir. What I've done so far: Boot a live system Extract LVM2 metadata from the working HDD using dd Copy metadata to /etc/lvm/backup/vg0 Now I'm trying to do this: pvcreate --restore /etc/lvm/backup/vg0 --uuid "[uuid of my working hdd]" /dev/sdb2 But I always get: Couldn't find device with uuid '[uuid of broken hdd]'. Couldn't find device with uuid '[uuid of working hdd]'. Device /dev/sdb2 not found (or ignored by filtering). I confirmed that /dev/sdb2 exists and I've commented out all filtering settings from /etc/lvm/lvm.conf so I don't know what might be causing pvcreate not to find the device. So: What might be the problem? Is it even possible to restore this partition? (As I'm writing this I'm starting to think it's impossible D:) Edit: Okay, looks like I've got it figured out. I was using a Ubuntu 8.10 CD (yeah, I know it's not supported anymore) and it seems that was the problem. When I started from a Ubuntu 10.04 CD everything worked 'fine', I could mount my LVM partitions partially without problems. (Will answer the question in 4 hours. But if anyone has still got some hints/tips, please share! :)

  Read the article

• Virtualized Screen Resolution

  - by Jim R

  I have a 64 bit Ubuntu 9.10 workstation with two virtualized guest OSes using KVM/QEMU. Also both 64-bit. One is Fedora 12 the other is beta of Ubuntu 10.04. The problem is that I would like to use a larger size display that is configured by default. Both guest OSes have a maximum screen resolution of 1024x768. I would like to increase this to something like 1280x900 or 1440x900. The resolution of the host system is 1920x1080. This configuration appears to be a result of the installation detecting the resolution being reported by the virtual screen during installation. The only information I have found on the subject suggests modifying the xorg.conf file in the /etc/X11 directory. Neither guest system has this file. I tried creating one by hand in the Fedora system and managed to render it completely unusable. Not a big deal as this is recently installed and can be reinstalled easily. Is what I want to do possible? If so, how do I accomplish it?

  Read the article

• Virtualized Screen Resolution

  - by Jim R

  I have a 64 bit Ubuntu 9.10 workstation with two virtualized guest OSes using KVM/QEMU. Also both 64-bit. One is Fedora 12 the other is beta of Ubuntu 10.04. The problem is that I would like to use a larger size display that is configured by default. Both guest OSes have a maximum screen resolution of 1024x768. I would like to increase this to something like 1280x900 or 1440x900. The resolution of the host system is 1920x1080. This configuration appears to be a result of the installation detecting the resolution being reported by the virtual screen during installation. The only information I have found on the subject suggests modifying the xorg.conf file in the /etc/X11 directory. Neither guest system has this file. I tried creating one by hand in the Fedora system and managed to render it completely unusable. Not a big deal as this is recently installed and can be reinstalled easily. Is what I want to do possible? If so, how do I accomplish it?

  Read the article

• 3 Servers, is this is a cluster?

  - by Andy Barlow

  Hello, At the moment I have one Ubuntu server, 9.10, running with a simple Samba share, a mail server, DNS server and DHCP server. Mostly its just there for file sharing and email server. I also have 2 other servers that are exactly the same hardware and spec as the first, which have an rsync set up to retrieve the shared folders and backs them up. However, if the first server goes down, all of our shares disappear along with our mail and the system must be rebuilt. Also I tend to find if people are downloading a large amount from the file server, no-one can access there emails - especially in the morning when everyone is signing in at once. Would it be more beneficial for me to have all 3 servers, all running the same services, doing the same thing with some sort of cluster with load balancing? I'm not really sure where to begin looking, or how to go about such a setup where 3 servers are all identical, but perhaps one acts as the main load balancer?? If someone can point me in the right direction, or if this simply sounds like one of those Enterprise Cloud's that is now a default setup in Ubuntu Server 9.10+, then I'll go down that route. Cheers in advance. Andy

  Read the article

• What do I need to do to set my computer as Default Gateway?

  - by Vaibhav

  We are trying to put together a box with dual LAN cards (let's say Outer and Inner), where the Inner LAN card is supposed to act as a default gateway on the network it is connected to. This box is running Ubuntu. The basic purpose for this box is to take messages generated on the inner network, do some work with them and forward them out the Outer LAN card to a server. The inner network is completely isolated with simply a regular switch connecting the Inner LAN Card with two other boxes. These other boxes either throw out multi-cast messages (which the Inner LAN Card is listening to), or send out unicast messages meant for the server which is not on this inner network. So, we need the Inner LAN Card to act as a default gateway, where these unicast messages will then be sent, and the code on the dual-LAN Card box can then intercept and forward these messages to the server. Question: 1. How do we setup the LAN Card to be default gateway (does it need some configuration on Ubuntu)? 2. Once we have this setup, is it a simple matter of listening to the interface to intercept the incoming messages? Any help (pointers in the right direction) is appreciated. Thanks.

  Read the article

• Trying to setup catchall mail forwarding on my rackspace's cloudspace server

  - by bob_cobb

  I'm running Ubuntu 12 Precise Pangolin and am trying to configure my server to catchall mail sent to it and forward it to my gmail address. I've been trying lots of examples online like editing my main.cf file which looks like this: smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = destiny alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = destiny, localhost.localdomain, localhost relayhost = smtp.sendgrid.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 51200000 recipient_delimiter = + inet_interfaces = all inet_protocols = all In my /etc/postfix/virtual I have: @mydomain.com [email protected] @myotherdomain.com [email protected] Which isn't working when I email [email protected] or [email protected]. So I got the recommendation to add the following to my /etc/alias: postmaster:root root:[email protected] restarted postfix, and tried emailing [email protected] or [email protected] but it still won't send. Does anyone have any idea what I'm doing wrong here? I'd appreciate any help.

  Read the article

• Internet Radio Station for University

  - by ryan

  I am trying to help my University Student Radio station rethink the setup of the way they stream music, but I have some questions regarding the use of Ubuntu to stream music. Currently, the radio station uses two windows machines: one of which is used to stream the radio station and serve the website, and the other is used by rotating djs to select songs and create playlists. The computer used by djs feeds mono into the sound card of the server and the server streams the feed online. -Ideally I would like to maintain a two-computer setup: One computer as server, and another that is used to select and play music by rotating djs. -I would like to use Ubuntu for the server. -I would like to use Windows for the other machine. -The server should be able to stream song information. First, is there a way to somehow get the song information from an analog feed? Second, what is the best streaming server for radio? I have encountered shoutcast, icecast, and darwin, but I don't know where to begin in attempting to gauge them. Finally, if anyone has any tips or pointers about small internet radio station management/ setup they would be appreciated as this is my first radio station, and I am eager to hear of past experiences.

  Read the article

• pptpd-logwtmp.so config wrong ip address

  - by rgc

  i have setup a pptp vpn on ubuntu 10.04, and i config local ip address , remote ip address as following: local IP address 10.0.30.100 remote IP address 192.168.13.100 after i use windows to connect to vpn server in windows , i only could send packets, can not receive any packets. i also check the pptp log in ubuntu server, and find this strange thing rcvd [IPCP ConfAck id=0x1 <compress VJ 0f 01> <addr 10.0.30.100>] rcvd [IPCP ConfReq id=0x2 <compress VJ 0f 01> <addr 192.168.13.100> <ms-dns1 202.119.32.6> <ms-dns2 202.119.32.12>] sent [IPCP ConfAck id=0x2 <compress VJ 0f 01> <addr 192.168.13.100> <ms-dns1 202.119.32.6> <ms-dns2 202.119.32.12>] Cannot determine ethernet address for proxy ARP local IP address 10.0.30.100 remote IP address 192.168.13.100 pptpd-logwtmp.so ip-up ppp0 **172.25.146.174** i did not set 172.25.146.174, it should be 192.168.13.100, can anyone tell me what should i do to fix this problem?

  Read the article

• Karmic iptables missing kernel moduyles on OpenVZ container

  - by luison

  After an unsuccessful p2v migration of my Ubuntu server to an OpenVZ container which I am stack with I thought I would give a try to a reinstall based on a clean OpenVZ template for Ubuntu 9.10 (from the OpenVZ wiki) When I try to load my iptables rules on the VM machine I've been getting errors which I believe are related to kernel modules not being loaded on the VM from the /vz/XXX.conf template model. I've been testing with a few post I've found but I was stack with the error: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. FATAL: Could not load /lib/modules/2.6.24-10-pve/modules.dep: No such file or directory iptables-restore v1.4.4: iptables-restore: unable to initialize table 'raw' Error occurred at line: 2 Try `iptables-restore -h' or 'iptables-restore --help' for more information. I read about the template not loading all iptables modules so I added modules to the XXX.conf of the VZ virtual machine like this: IPTABLES="ip_tables iptable_filter iptable_mangle ipt_limit ipt_multiport ipt_tos ipt_TOS ipt_REJECT ipt_TCPMSS ipt_tcpmss ipt_ttl ipt_LOG ipt_length ip_conntrack ip_conntrack_ftp ip_conntrack_irc ipt_conntrack ipt_state ipt_helper iptable_nat ip_nat_ftp ip_nat_irc" As the error remained I read that I should build dependencies again on the virtual machine: depmod -a but this returned an error: WARNING: Couldn't open directory /lib/modules/2.6.24-10-pve: No such file or directory FATAL: Could not open /lib/modules/2.6.24-10-pve/modules.dep.temp for writing: No such file or directory So I read again about creating the directory empty and redoing "depmod -a" it. I now don't get the dependancies error but get this and I don't have a clue how to proceed: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. FATAL: Module ip_tables not found. iptables-restore v1.4.4: iptables-restore: unable to initialize table 'raw' Error occurred at line: 2 Try `iptables-restore -h' or 'iptables-restore --help' for more information. I understand that iptables rules have to be different on the VM machine and perhaps some of the rules we are trying to apply (from our physical server) are not compatible but these are just source IP and destination port checks that I would like to be able to have available . I've heard that on the CentOS template there are no issues with this, so I understand is to do with VM config. Any help would be greatly appreciated.

  Read the article

• Why won't my service start, and why doesn't upstart output any errors?

  - by Alex Waters

  I am trying to 'start gunicorn' as a service via upstart as user ale. I'm using gunicorn/flask on ubuntu 12.04 w/ init (upstart 1.5) Here is my /etc/init/gunicorn.conf setuid btw setgid flask script export HOME=/home/btw export WORKON_HOME=$HOME/.virtualenvs . $HOME/.virtualenvs/default/bin/activate cd $HOME/flask workon default gunicorn -c gunicorn.py bw:app end script It doesn't output anything other than gunicorn start/running, process 12992. If i then do 'status gunicorn' I get stop/waiting. any ideas on how to debug this? I tried following http://upstart.ubuntu.com/wiki/Debugging but it didn't help. If I do the following as user ale in the app's directory: 1. workon default 2. gunicorn -c gunicorn.py bw:app then Gunicorn runs fine. Here is ~/flask/gunicorn.py: bind = "0.0.0.0:8080" workers = 3 backlog = 2048 worker_class = "gevent" debug = True daemon = False pidfile ="/tmp/gunicorn.pid" log_level = "debug" accesslog = "/var/log/gunicorn/access.log" errorlog = "/var/log/gunicorn/error.log" user = "btw" group = "flask" Also, /var/log/error.log doesn't show anything new when I try to start the Gunicorn service. If I start it manually, it shows that the workers have been loaded, etc. Thanks for any help / suggestions!

  Read the article

• publickey authentication only works with existing ssh session

  - by aaron

  publickey authentication only works for me if I've already got one ssh session open. I am trying to log into a host running Ubuntu 10.10 desktop with publickey authentication, and it fails when I first log in: [me@my-laptop:~]$ ssh -vv host ... debug1: Next authentication method: publickey debug1: Offering public key: /Users/me/.ssh/id_rsa ... debug2: we did not send a packet, disable method debug1: Next authentication method: password me@hosts's password: And the /var/log/auth.log output: Jan 16 09:57:11 host sshd[1957]: reverse mapping checking getaddrinfo for cpe-70-114-155-20.austin.res.rr.com [70.114.155.20] failed - POSSIBLE BREAK-IN ATTEMPT! Jan 16 09:57:13 host sshd[1957]: pam_sm_authenticate: Called Jan 16 09:57:13 host sshd[1957]: pam_sm_authenticate: username = [astacy] Jan 16 09:57:13 host sshd[1959]: Passphrase file wrapped Jan 16 09:57:15 host sshd[1959]: Error attempting to add filename encryption key to user session keyring; rc = [1] Jan 16 09:57:15 host sshd[1957]: Accepted password for astacy from 70.114.155.20 port 42481 ssh2 Jan 16 09:57:15 host sshd[1957]: pam_unix(sshd:session): session opened for user astacy by (uid=0) Jan 16 09:57:20 host sudo: astacy : TTY=pts/0 ; PWD=/home/astacy ; USER=root ; COMMAND=/usr/bin/tail -f /var/log/auth.log The strange thing is that once I've got this first login session, I run the exact same ssh command, and publickey authentication works: [me@my-laptop:~]$ ssh -vv host ... debug1: Server accepts key: pkalg ssh-rsa blen 277 ... [me@host:~]$ And the /var/log/auth.log output is: Jan 16 09:59:11 host sshd[2061]: reverse mapping checking getaddrinfo for cpe-70-114-155-20.austin.res.rr.com [70.114.155.20] failed - POSSIBLE BREAK-IN ATTEMPT! Jan 16 09:59:11 host sshd[2061]: Accepted publickey for astacy from 70.114.155.20 port 39982 ssh2 Jan 16 09:59:11 host sshd[2061]: pam_unix(sshd:session): session opened for user astacy by (uid=0) What do I need to do to make publickey authentication work on the first login? NOTE: When I installed Ubuntu 10.10, I checked the 'encrypt home folder' option. I'm wondering if this has something to do with the log message "Error attempting to add filename encryption key to user session keyring"

  Read the article

• wget is working only when used with sudo

  - by Yusuf

  I'm having quite a strange behavior with wget since yesterday. I can download files by using sudo wget, but when I try the same file with only wget, I can get this error: yusufh@ubuntu-yuh:~$ wget http://www.kegel.com/wine/winetricks --2010-12-17 09:34:11-- http://www.kegel.com/wine/winetricks Resolving www.kegel.com... failed: Name or service not known. wget: unable to resolve host address `www.kegel.com' and with sudo wget: yusufh@ubuntu-yuh:~$ sudo wget http://www.kegel.com/wine/winetricks --2010-12-17 09:35:37-- http://www.kegel.com/wine/winetricks Connecting to 127.0.0.1:5865... connected. Proxy request sent, awaiting response... 200 OK Length: 190672 (186K) [text/plain] Saving to: `winetricks' 100%[==================================================================================================>] 190,672 --.-K/s in 0.03s 2010-12-17 09:35:37 (6.92 MB/s) - `winetricks' saved [190672/190672] After the comments below, here is an update: I can use Google Chrome or Firefox perfectly without running it as root. I use ntlmaps to connect to the office proxy. So I need to use 127.0.0.1:5865 as the proxy for clients. Result for env | grep -i proxy: NO_PROXY=localhost,127.0.0.0/8,*.local, http_proxy=127.0.0.1:5865 ftp_proxy=127.0.0.1:5865 all_proxy=socks://127.0.0.1:5865/ ALL_PROXY=socks://127.0.0.1:5865/ https_proxy=127.0.0.1:5865 no_proxy=localhost,127.0.0.0/8,*.local while sudo env | grep -i proxy is empty! HELP!

  Read the article

• Securing SSH/SFTP and best practices on security

  - by MultiformeIngegno

  I'm on a fresh VPS with Ubuntu Server 12.04. I wanted to ask you the good practices to apply to enhance security over a stock Ubuntu-server. This is what I did up to now: I added Google Authenticator to SSH, then I created a new user (whom I'll use instead of 'root' for SSH & SFTP access) which I added to my /etc/sudoers list below 'root', so now it's: # User privilege specification root ALL=(ALL:ALL) ALL new_user ALL=(ALL:ALL) ALL Then I edited sshd_config and set PermitRootLogin to 'no'. Then restarted the ssh service. Is this ok? There are a few things I'd like to ask you though: 1) What's the sense of adding a new (sudoer) user whilst the root user still exist (ok it can't access with root privilege but it's still there..)? 2) System files are owned by 'root'.. I want to use my new_user to access via SFTP but with it I can't edit those files!! Should I mass-CHMOD 'em so that new_user has write perms too? What's the good practice on this? Thanks in advance, I hope you'll tell me if I did something wrong and/or other ways to secure the system. :)

  Read the article

• PHP sessions currupt

  - by Baversjo

  Using symfony framework 1.4 I have created a website. I'm using sfguard for authentication. Now, this is working great on WAMP (windows). I can login to several accounts on different browsers and use the website. I have ubuntu server 9.10 running apache (everything up to date and default configuration). On my server, when I login to the website in one browser it works great. When I on my other computer login with another user account on the public website, the login is successful. But when I refresh/go to another page the first user is shown as logged in instead! Also, when I press logout, It's not showing that I'm logged out after page load. When I press f5 again I'm logged out. As mentioned, all this works as expected on my local installation. I'm thinking there something wrong with my PHP session configuration on my ubuntu server, but I've never touched it.. Please help me. This is a school project and I'm presenting it today :(

  Read the article

< Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >