Search Results

Search found 11331 results on 454 pages for 'resource monitor'.

Page 358/454 | < Previous Page | 354 355 356 357 358 359 360 361 362 363 364 365  | Next Page >

• Hardware reserved memory issue

  - by Robert Koritnik

  I've seen lots of folks having problem with hardware reserved memory issue in Windows 7/Server 2008 R2. I have it myself but not as huge as others have. Problem description When you install Windows 7 (or its bigger brother Windows Server 2008 R2) your memory may not be fully utilised. If you look at Task Manager > Performance Tab > Resource Monitor > Memory Tab And scroll to the bottom of the list you will see a graphical representation of your memory. Some of it may be hardware reserved. Previous Windows versions didn't have this problem. System was able to utilise all memory available. Question Is there any solution to lower/remove hardware reserved memory? Sidenote I tried installing 32 and 64 bit versions but to no avail. I also tried both Windows: 7 and Server 2008 R2. But always get the same amount reserved by HW. On previous Windows versions I had more memory available because I'm simultaneously running 2 VMs on host (so three machines all together). And my memory peaks much higher now as it did on older versions.

  Read the article

• VLAN support on Juniper EX - 2200 switches

  - by liv2hak

  I have 6 Juniper switches (EX - 2200) connected to each other as shown in the network topology below. I have two PC's that I am using PC1 - (used for configuring the 6 switches via minicom) PC2 - to monitor the traffic between the switches via the Ports that are marked with arrows in the diagram. STEP 1: I create a new vlan On Switch 3 (SW3) that includes Port 12 and Port 22. I also assign l3-interface to the vlan (vlan_2) with ip address - 192.168.1.7. Now I plug-in Port 0 of Switch 3 on PC2. Now I try pinging 192.168.1.7 from PC2 (192.168.1.10) I want to know what will happen? My postulation is that I will not be able to ping SW3 from PC2.This is because SW3 (Port 12 and Port 22) is a part of a vlan_2 and vlan_2 logically breaks up broadcast domains and so 192.168.1.7 will not be reachable from 192.168.1.10. Now I have an l3-interface on SW1 with IP 192.168.1.1 using default vlan( vlan-id 0). Similarly I have enabled IP on SW2 - 192.168.1.2 SW3 - 192.168.1.3 SW4 - 192.168.1.4 SW5 - 192.168.1.5 SW6 - 192.168.1.6 all using default vlan. Now I plug in Port 12 of SW3 (blue cable) into the PC2. I try to ping 192.168.1.1 from PC2. What will happen at this stage.? My postulation is that I will be able to ping switch 1.Is this correct? Also another question is that can a single port on a Switch be added multiple VLANS? I am a beginner at network configuration? Any help would be highly appreciated. (Please ignore the CISCO symbol on the switches in the diagram.All swithes are Junper EX 22-00.)

  Read the article

• Nagios returns "No output returned from plugin" running process

  - by user56291

  I have a nagios server and a bunch of nagios clients that i currently monitor. All the clients are setup with the following nrpe configuration. check_users, check_load... metrics are successfully displayed on the nagios interface but check_nginx and check_server_proxy displayed as "Unknown"-(No output returned from plugin). As far as i understood nagios simply runs ps command and looks for either the argument strings or the name of the command to verify whether the service is running. Also with -c flag, one can give nagios a threshold to determine the output (ie: -c 1 returns 'OK' for if it finds at least 1 process.) nrpe_local.cfg: ###################################### # Do any local nrpe configuration here ###################################### allowed_hosts =127.0.0.1,10.0.2.181 command[check_users]=/usr/lib/nagios/plugins/check_users -w 5 -c 10 command[check_load]=/usr/lib/nagios/plugins/check_load -w 15,10,5 -c 30,25,20 command[check_all_disks]=/usr/lib/nagios/plugins/check_disk -w 20% -c 10% command[check_zombie_procs]=/usr/lib/nagios/plugins/check_procs -w 5 -c 10 -s Z command[check_total_procs]=/usr/lib/nagios/plugins/check_procs -w 150 -c 200 command[check_swap]=/usr/lib/nagios/plugins/check_swap -w 50% -c 25% command[check_server_proxy]=/usr/lib/nagios/plugins/check_procs -c 1 -a "api-v1/server.js" command[check_nginx]=/usr/lib/nagios/plugins/check_procs -c 1:30 -C nginx nagios_server.cfg ... define host{ use generic-host ; Name of host template to use host_name plum alias plum address 10.0.2.88 check_command check-host-alive-by-ssh } ... #Check api-proxy-server define service{ use generic-service host_name plum service_description check api proxy service check_command check_nrpe!check_server_proxy } define service { use generic-service ; Name of service template to use host_name plum service_description CHECK_NGINX check_period 24x7 max_check_attempts 3 normal_check_interval 5 retry_check_interval 3 check_command check_nrpe!check_nginx notifications_enabled 1 } Also when i run the command on the nagios client: /usr/lib/nagios/plugins/check_procs -c 1 -a "api-v1/server.js" I get the desired output PROCS OK: 1 process with args 'api-v1/server.js' I would really appreciate any pointers that might help me solve why it nrpe command does not return the desired output on the nagios server panel.

  Read the article

• Implement QoS/Bandwidth Management or Upgrade Bandwidth?

  - by Michael

  A question that I'm faced with currently. Here's my setup: Cisco ASA 5510 15Mbps Internet Connection @ $1350/month The bandwidth was originally meant for 35-45 people but we've grown quite quickly to roughly 60-65 people. Needless to say, when I check bandwidth logs it's almost always spiked at 15Mbps. I did use Wireshark to do some poking around to see what was hogging up our bandwidth but with everything running through CDNs and Cloud Services it proved difficult to get a good grasp of where our bandwidth was going. So the question is do I ONLY implement bandwidth management through ASA OR upgrade the Internet to 50Mbps ($1600/month) and then implement bandwidth management through ASA? Any suggestions on how to segment the 15Mbps connection if we decided ONLY to go with the bandwidth management solution? Thanks. UPDATE 1 Installed PRTG and used packet content to monitor the traffic. As I suspected still pretty vague. My Top Connections include the following: a204-2-160-16.deploy.akamaitechnologies.com ec2-50-16-212-159.compute-1.amazonaws.com a204-2-160-48.deploy.akamaitechnologies.com a72-247-247-133.deploy.akamaitechnologies.com mediaserver-sv5-t1-1.pandora.com Other than the Pandora destination, the rest doesn't tell me much on how to properly control the bandwidth. Any thoughts or suggestions? Thanks. M

  Read the article

• Can compressing Program Files save space *and* give a significant boost to SSD performance?

  - by Christopher Galpin

  Considering solid-state disk space is still an expensive resource, compressing large folders has appeal. Thanks to VirtualStore, could Program Files be a case where it might even improve performance? Discovery In particular I have been reading: SSD and NTFS Compression Speed Increase? Does NTFS compression slow SSD/flash performance? Will somebody benchmark whole disk compression (HD,SSD) please? (may have to scroll up) The first link is particularly dreamy, but maybe head a little too far in the clouds. The third link has this sexy semi-log graph (logarithmic scale!). Quote (with notes): Using highly compressable data (IOmeter), you get at most a 30x performance increase [for reads], and at least a 49x performance DECREASE [for writes]. Assuming I interpreted and clarified that sentence correctly, this single user's benchmark has me incredibly interested. Although write performance tanks wretchedly, read performance still soars. It gave me an idea. Idea: VirtualStore It so happens that thanks to sanity saving security features introduced in Windows Vista, write access to certain folders such as Program Files is virtualized for non-administrator processes. Which means, in normal (non-elevated) usage, a program or game's attempt to write data to its install location in Program Files (which is perhaps a poor location) is redirected to %UserProfile%\AppData\Local\VirtualStore, somewhere entirely different. Thus, to my understanding, writes to Program Files should primarily only occur when installing an application. This makes compressing it not only a huge source of space gain, but also a potential candidate for performance gain. Testing The beginning of this post has me a bit timid, it suggests benchmarking NTFS compression on a whole drive is difficult because turning it off "doesn't decompress the objects". However it seems to me the compact command is perfectly capable of doing so for both drives and individual folders. Could it be only marking them for decompression the next time the OS reads from them? I need to find the answer before I begin my own testing.

  Read the article

• Dell Management Packs in System Center Operations Manager 2007 R2?

  - by bwerks

  Hey all, I recently set up SCOM in a small business network environment. The root management server is a Dell Poweredge 2950, and I'd like to use SCOM to monitor it using Dell's management packs. I've imported the management packs into the SCOM deployment and followed Dell's installation instructions, but it doesn't seem to be fully working yet. Currently, the Diagram views in the Dell tree (Monitoring tab) seem to show me the server's place in the network topology, so it seems that at least part of it is working. However, none of the reports under "Performance and Power Monitoring Views" provide any information. When clicking on one of them (Power Consumption (Watts), for instance), the display area is blank and there is a tooltip visible that reads "No performance counter is selected. To select a counter, place a check mark in the Show column in legend below." However, in the legend, there's nothing there for me to check. I've installed OpenManage 6.2 on the server as per the Dell documentation, but I don't know what else I could have done that I missed. Does this sound like a familiar problem to anyone?

  Read the article

• Activation context generation failed for "C:\php\php-cgi.exe". Dependent Assembly

  - by Eyla

  Greeting, I have Windows Server 2008 Server Core. I want to configure this server to host php websites using IIS 7. I installed and configured IIS7 to run php using the steps in this website: http://blogs.msdn.com/b/philpenn/archive/2009/07/19/deploying-iis-7-5-fastcgi-php-on-server-core.aspx Now I’m facing a problem that when I request my php website I would get this error. Server Error 500 - Internal server error. There is a problem with the resource you are looking for, and it cannot be displayed. I check the even log and I found these details too: Activation context generation failed for "C:\php\php-cgi.exe". Dependent Assembly Microsoft.VC90.CRT,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="9.0.21022.8" could not be found. Please use sxstrace.exe for detailed diagnosis. I search about this error and I found a solution for it but which is to install Microsoft Visual C++ 2008 SP1 Redistributable Package (x86). I installed but still I’m getting same error. Please help me to solve this problem and let me know if you want to know more info about my issue.

  Read the article

• How do I locate the app generating this network traffic?

  - by Christopher Bartels

  I don't know what this process is doing on my computer. I run Windows 7 Professional w/ all its updates running current non-free antivirus. I only see it in Resource Monitor, where you can see the Network Service process connected to bitum.nnov.ru. When my PC's network traffic generating apps are idle, this process is using the most of all the idle processes using the network. Screenshot hosted here: http://sss.proinbox.com/bitum-nnov-ru.jpg Does anyone recognize this? The page source mentions a control port & a stream port: Page Source for http://bitum.nnov.ru : <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <title>DVR WebViewer</title> <meta http-equiv="Content-Type" content="text/html; charset=euc-kr"> </head> <body topmargin="0" leftmargin="0"> <OBJECT classid="clsid:EE479A40-C128-40DD-93DA-000556AF9607" codebase="CtrWeb.cab#version=1,0,2,2" width=875 height=585 align=center hspace=0 vspace=0 > <param name="CmdPort" value="5920"> <param name="StreamPort" value="5921"> </body> </html> When I google this page's title, I see a number of other domains that host the same page. Whois: domain: NNOV.RU nserver: ns.kis.ru. nserver: ns.nnov.ru. 78.25.80.210 nserver: ns1.kis.ru. nserver: ns2.kis.ru. state: REGISTERED, DELEGATED, VERIFIED org: "Agentstvo Delovoj Svjazi", Ltd registrar: RU-CENTER-REG-RIPN admin-contact: https://www.nic.ru/whois created: 1996.10.23 paid-till: 2012.11.01 free-date: 2012.12.02 source: TCI Last updated on 2012.06.16 04:20:46 MSK

  Read the article

• What's the right way to start a node.js service?

  - by elliot42

  I'm running a node.js service (statsd) on CentOS 6. What's the proper way to daemonize and start such a service? Potential Daemonizers--are daemonizers supposed to be language-specific or general?: forever (node-specific) daemonize nohup (presumably wrong) start-stop-daemon(debian-only? is this for daemonizing or starting/stopping? what is the Centos equivalent?) Should the app itself really know how to daemonize itself and then have a -d flag? (e.g. via node-daemonize2 or forever-monitor?) Service starters--should these be from the system/distro, or should they be from monitoring tools such as monit?: service? is really /etc/init.d on CentOS? service? is really Upstart on Ubuntu? monit? daemontools? runit? I'm unfortunately new to this--where can I read up on what is the most standard, classic, reliable way of doing this?

  Read the article

• nginx with stub_status.. need help with nginx.conf

  - by Amar

  Hello I am trying to setup nginx with stub status so I can monitor nginx requests etc.. with serverdensity.com. I needed to put something like this in nginx.conf server { listen 82.113.147.xxx; location /nginx_status { stub_status on; access_log off; allow 82.113.147.xxx; deny all; } } And with this monitoring acctualy works. However It seems I lost "include" part in my nginx.conf and now none of vhosts in sites-enabled work. Here is a bit more of my nginx.conf http { include /etc/nginx/mime.types; default_type application/octet-stream; server_tokens off; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_comp_level 2; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; server { listen 82.113.147.226; location /nginx_status { stub_status on; access_log off; allow 82.113.147.226; deny all; } } } Hope someone can help me with this , as I belive its minor issue, its just that "I dont see it" ty

  Read the article

• 426 Connection closed; transfer aborted.

  - by Jiaoziren

  Hi, I have an IIS FTP set up on Windows 2003 SP2 (S1). Everyday in the early morning, a script on another server (S2) will run and initiate FTP transfer of pulling log files from S1 to S2. The FTP client we're using is built-in FTP.exe in Windows 2000 on S2. Recently we replaced S1 with a new server however we kept the IP address. There are multiple IP addresses on new S1. Ever since the new S1 was in place, the '426 Connection closed; transfer aborted.' errors haven been occuring randomly. The log indicated that the transfer started ok however the file cannot be transferred completely, as per log below: mget access*.log 200 Type set to A. 200 PORT command successful. 150 Opening ASCII mode data connection for access02232010.log(205777167 bytes). 426 Connection closed; transfer aborted. ftp: 20454832 bytes received in 283.95Seconds 72.04Kbytes/sec. The firewall monitor suggested that the connection was setup in passive mode however I've been told that MS FTP.exe doesn't support passive mode. Though I can see the response of 'entering passive mode' from server when typing in 'quote pasv'. My network admin has told me to try the transfer in active mode however I don't know how to open active mode on client side. It's getting really frustrating. Wish someone here has the right knowledge/experience could shed me a light. Cheers.

  Read the article

• Intel Core i7 QuadCore on HP Pavilion dv7 Overheating Issues

  - by kellax

  I bought a brand new HP notebook: HP Pavilion dv7-6b21em BeatsAudio edition. The notebook is about 2 months old and has pretty nasty overheating problem. I mainly use it for development however i do play some games. The disturbing thing is that the computer is loud on pretty simple tasks. Here are the specs: CPU: Intel Core i7-2670QM QuadCore ( 8 threads ) @ 2.20 GHz RAM: ( 8GB ) 2x 4GB @ 1066 HDD: 1TB 7200 GPU: ATI Radeon HD 6770M 1GB Dedicated DDR OS: Windows 7 64bit Enterprise I have an external monitor runing on VGA port an 22' Samsung SyncMaster S24B300 CPU Heat Statistics Platform: rPGA 988B (Socket G2) Frequency: cca. 3000 Mhz VID: 1.1809 - 1.2059 v Revision: D2 CPUID: 0x206A7 TDP: 45.0 Wats, Lithographu: 32 nm Heat: Tj. Max: 100*C, Power 4.5 - 5.9 Wats Core #0: 63*C Load on all is about 0 to 2% Core #1: 65*C Core #2: 66*C Core #3: 67*C I opened the notebook the fan is working fine there is no dust but still right now the fan is pretty loud even tho all i have open is FireFox. When i run a game the heat jumps to whopping 90-97*C. It has not shut down due to overheating yet but the loud fan is pretty annoying considering I'm not really doing anything stressfull. Is there anything i can do to fix this is it maybe a BIOS issue ? I have all drivers updated tho to the latest. I have very few background processes running consuming bare 2GB of RAM and about 2% of CPU. I had it serviced they said there is nothing wrong with it. But i feel that a Notebook that costs 1.2k Euros cant be like this.

  Read the article

• Throttling Postfix memory

  - by teddybeard

  I have a VPS on 1and1 similar to this configuration (512MB, burst up to 2GB). I run a web service where I crawl the web and notify my users through email and sms when a certain online data feed changes. When I send the emails out, I just have PHP loop through the recipients list and send the emails out using the mail() function. Whenever I try to send a large volume of these messages out, my server starts acting funny. I can't even run an 'ls' sometimes because the shell tells me it 'cannot allocate memory'. The shell is unusable and yet my website is being served up fine. Mail.err contains: Nov 14 17:30:09 s15351477 postfix/smtp[26000]: fatal: inet_addr_local[getifaddrs]: getifaddrs: Cannot allocate memory Nov 14 17:30:09 s15351477 postfix/sendmail[25999]: fatal: username(1000): unable to execute /usr/sbin/postdrop -r: Success Nov 14 18:29:14 s15351477 postfix/smtp[9911]: fatal: inet_addr_local[getifaddrs]: getifaddrs: Cannot allocate memory Nov 14 18:29:14 s15351477 postfix/sendmail[9910]: fatal: username(1000): unable to execute /usr/sbin/postdrop -r: Success Also, if relevant, my bean counters are: Version: 2.5 uid resource held maxheld barrier limit failcnt 53907331: kmemsize 20779422 21041560 31457280 34603008 2989403 lockedpages 0 0 512 512 0 privvmpages 81488 82498 524288 576716 94640 shmpages 2831 2831 32768 32768 0 dummy 0 0 9223372036854775807 9223372036854775807 0 numproc 90 91 128 128 6603 physpages 32692 33531 2147483647 2147483647 0 vmguarpages 0 0 131072 2147483647 0 oomguarpages 32942 33781 9223372036854775807 2147483647 0 numtcpsock 22 23 720 720 0 numflock 27 28 376 413 0 numpty 1 1 32 32 0 numsiginfo 0 1 512 512 0 tcpsndbuf 425888 441064 3440640 5406720 0 tcprcvbuf 369200 376832 3440640 5406720 0 othersockbuf 268000 268464 2252160 4194304 0 dgramrcvbuf 0 8472 524288 576716 0 numothersock 180 182 720 720 0 dcachesize 952146 966231 5242880 5767168 0 numfile 3609 3683 8192 8192 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 25 25 200 205 0 Is there some way I can throttle postfix to keep it from swamping the system like this? Also wondering: why does email use so many resources, these emails are just short text?

  Read the article

• authbind, privbind or iptables REDIRECT (port 80 to 8080)?

  - by chris_l

  Hi, I'd like to run Glassfish v3 as a non-privileged user on Linux (Debian), but make it available on port 80. I'm currently doing this with iptables: iptables -t nat -I PREROUTING -p tcp -d x.x.x.x --dport 80 -j REDIRECT --to-port 8080 This works, but I wonder: If this has any significant performance impact compared to binding directly to port 80 If I could make a similar setup also work for HTTPS (or if that must run on 443) If there's a way to avoid other users from binding to port 8080 (in case my server crashes) - maybe block that port permanently to other users somehow? ...or if I should use authbind/privbind instead? Problem: I couldn't make it work with authbind or privbind so far. For authbind, I edited asadmin's last line to: exec authbind --deep "$JAVA" -Djava.net.preferIPv4Stack=true -jar ... For privbind: exec privbind -u glassfish "$JAVA" -Djava.net.preferIPv4Stack=true -jar ... (Only) with these settings, I can successfully perform a create-domain --domainport 80. This proves, that authbind and privbind actually work (the authbind version of the script is called by the glassfish user; the privbind version is called by root of course). However, in both cases I get the following exception, when starting the domain (start-domain): [#|2010-03-20T13:25:21.925+0100|SEVERE|glassfishv3.0|javax.enterprise.system.core.com.sun.enterprise.v3.server|_ThreadID=11;_ThreadName=FelixStartLevel;|Shutting down v3 due to startup exception : Permission denied: 80=com.sun.enterprise.v3.services.impl.monitor.MonitorableSelectorHandler@1fc25e5|#] I haven't found a solution for that yet (after searching the web, it seems, that this isn't so easy?) But maybe, the solution with iptables is good enough - what do you think? Thanks, Chris

  Read the article

• Is there a way to tell what the download speed is from a site/server

  - by Memor-X

  i'm looking into which ISP i should go with at the place i'm moving into, one ISP which i have been told good things about has data limits (which when breached will drop your speed to dial-up speed) but multiple memberships which, apart from the cheapest membership, have the same data limits (the cheapest has a 10GB data limit) in their fine print, they say that each different membership has different port speeds, one particular part jumps out at me These speeds are the NBN (National Broadband Network) port speed and not the actual Internet data speed which will vary based on numerous factors including destination you are reaching, your network equipment, network congestion etc. i plan to use the net to download DLC and patch updates for games (particular the insanely large update for the Wii U) and games from Steam (if i find any good one other than this one JRPG) and downloading development resources from free sites like Deposit Files and Mediafire since one membership with a 1000GB data limit is $145 with the port speed being 12Mbps/1Mbps (cheapest) while another with the same limit is $190 with the port speed of 100Mbps/40Mbps (expensive) i am wondering how i can tell what the speed coming from site is since i don't want to be wasting money on speed that makes no difference (unlike memory which i rather have to spare) NOTE: the speeds are for a fiber optic network which where my new place is can only connect via fixed wireless which i may not be able to get with this ISP but if i can get this network then good NOTE 2: most of the resources i get from Deposit Files are always about 200 MB or less, if a resource pack is greater then it's split into multiple archives (like .7z.part) while Mediafire i have to see one bigger than 150MB NOTE 3: one update patch for a PS3 game is close to 4 GB (Disgaea 4) which i need to get access to the DLC and on the weekend i downloaded 5 GB for the Final Fantasy XIV Open Beta for the PS3 which took almost 5 hours

  Read the article

• Sharepoint db issue after DB move to SQL 08

  - by JohnyV

  Recently we have moved our sharepoint 2007 db from sql 2000 server to 2008 x64 SQL server. All seems well, however there is a problem where the sql server stops running and the service has to be restarted. The errors mention insufficient internal memory etc. I have tried to start the db using -g384 which is the default in sql 2000 but 256 is default for 2008 I believe. This has not rectified the issue. I was advised that perhaps the issue may be rectified by upgrading to wss 3.0 sp2 however When I have tried to install this i get another error post sp2 update and have to refer back to a vm snapshot. The error after the service pack is Server error: http://go.microsoft.com/fwlink?LinkID=96177 So I guess I have a few questions How can I fix the first issue and the 2nd issue. I have checked out many forums and posts and have tried a few things and still get no joy. Any assistance would be great. UPDATE I have fixed the Server error: http://go.microsoft.com/fwlink?LinkID=96177 the i needed to run the wss sp2 as well as the office servers sp2 then the config wizard then the moss configuration worked. The errors I am getting in SQL are SQL Server was unable to run a new system task, either because there is insufficient memory or the number of configured sessions exceeds the maximum allowed in the server. Verify that the server has adequate memory. Use sp_configure with option 'user connections' to check the maximum number of user connections allowed. Use sys.dm_exec_sessions to check the current number of sessions, including user processes. A read operation on a large object failed while sending data to the client. A common cause for this is if the application is running in READ UNCOMMITED isolation level. The connection will be terminated. There is insufficient system memory in resource pool 'internal' to run this query. These errors are by a user that was created as a service for sharepoint.

  Read the article

• Linux Distro for Beginners

  - by XLR3204S

  Well... I know that's the question arising all over the Internet, but I couldn't find an answer to suit me after googling for quite some time. I'd like to get a Linux distribution, and start learning using the CLI. I'm looking for a distribution already having GNOME installed, as I'll be using Linux-Command.org as my learning resource, and I'm not very familiar with CLI-based web browsers. I'd mainly like to get to know my way around a UNIX-based system, and then I think I'd like to pick up a CLI-only distribution, and start doing more complex stuff. I've tried Ubuntu, Fedora Core, OpenSolaris and FreeBSD (the last two aren't linux distros, I know). Ubuntu and FC are fine, they do come with Firefox, but I'm not really sure they're meant for learning purposes. OpenSolaris was OK as well, but I haven't got to play with it enough. FreeBSD 7.2 did not want to install itself on my 13" MacBook Pro, it generated a kernel panic everytime while copying the files to the disk. So to sum this up, I'm trying to learn Linux, and I'm willing to invest time into this (that is, not giving up when the first problems arise). I also have intermediate knowledge of C++, if it helps, and I'm also using the CLI-vim to write small C++ CLI-based programs, so text editing should be any problem. And... speaking of Macs, how am I going to be limited if I try to learn how to use UNIX-based systems using the OS X Terminal? It uses bash 3.2, isn't this the same shell as the one found on most of the Linux machines? How does the fact that OS X is based on FreeBSD 4.4, if I'm not mistaking, affect this? Thanks in advance, and hopefully, I'll have a starting point ASAP.

  Read the article

• How can I filter /var/adm/wtmpx on Solaris 10?

  - by Yanick Girouard

  Some of our Solaris 10 servers are monitored using SiteScope, which uses Telnet to probe certain ports (SSH is one of them) every few minutes. This is creating an insane amount of lines in /var/adm/wtmpx, and eventually make it so big (2,5G+) that we can no longer run the last command, or that the uptime command is unable to accurately show the true uptime of the server. The error we get when trying to run the last command is this: /var/adm/wtmpx: Value too large for defined data type I have found ways we can clean this accounting log using a cron job (with the command /usr/lib/acct/fwtmp), and this works. This is not the issue. I was wondering if there would be a way to simply prevent connections from the monitoring user (in our case, user monsite) from creating entries in this accounting log at all. Is this possible, and if so, how can I do it? I've looked around and searched Google for a while, but couldn't find an answer to this question. NOTE: We are very well aware that the monitoring solution we employ is perhaps not the best one, but we cannot change it at this time. Therefore, suggesting that we change it is not pertinent to this question. If you want to read more on the Sitescope monitoring solution we employ for those servers, please see its documentation here and look for Port Monitor, and Connecting to remote UNIX servers, which explains how it works.

  Read the article

• Oracle 10g for Windows does not start up on system boot

  - by Mike Dimmick

  We have an Oracle 10g Enterprise Edition installation (10.2.0.1.0) on a Windows Server 2003 virtual machine. It was initially created with Virtual Server 2005 R2 SP1 but has now been migrated to Windows Server 2008 Hyper-V. The services start on system boot, but the instance does not start up. This problem was actually occurring on Virtual Server after a migration from one server to another, but I managed to fix it then with: oradim -edit -sid ORCL -startmode auto However, this now has no effect. oradim.log (in %OracleHome%\database\oradim.log) says: Thu Jun 10 14:14:48 2010 C:\oracle\product\10.2.0\db_3\bin\oradim.exe -startup -sid orcl -usrpwd * -log oradim.log -nocheck 0 Thu Jun 10 14:14:48 2010 ORA-12560: TNS:protocol adapter error sqlnet.log in the same folder has: Fatal NI connect error 12560, connecting to: (DESCRIPTION=(ADDRESS=(PROTOCOL=BEQ)(PROGRAM=oracle)(ARGV0=oracleorcl)(ARGS='(DESCRIPTION=(LOCAL=YES)(ADDRESS=(PROTOCOL=beq)))'))(CONNECT_DATA=(SID=orcl)(CID=(PROGRAM=C:\oracle\product\10.2.0\db_3\bin\oradim.exe)(HOST=ORACLE-VM)(USER=SYSTEM)))) VERSION INFORMATION: TNS for 32-bit Windows: Version 10.2.0.1.0 - Production Oracle Bequeath NT Protocol Adapter for 32-bit Windows: Version 10.2.0.1.0 - Production Time: 10-JUN-2010 14:14:48 Tracing not turned on. Tns error struct: ns main err code: 12560 TNS-12560: TNS:protocol adapter error ns secondary err code: 0 nt main err code: 530 TNS-00530: Protocol adapter error nt secondary err code: 2 nt OS err code: 0 The ORA_ORCL_AUTOSTART registry value is set to TRUE, so it should be auto-starting - and you can see that it's trying to. The problem also occurs when stopping and restarting the OracleServiceORCL service. I've enabled SQL*Net tracing which shows: [10-JUN-2010 15:09:33.919] snlpcss: entry [10-JUN-2010 15:09:34.419] snlpcss: Unable to spawn Oracle oracle (DESCRIPTION=(LOCAL=YES)(ADDRESS=(PROTOCOL=beq))) orcl, error 2. [10-JUN-2010 15:09:34.419] snlpcall: exit On a hunch that error 2 is Windows error 2 (file not found) I tried restarting the service with Process Monitor watching oradim.exe, but this appears to delay things just enough that it always works. Right now I have a horrible hack where I've created a Scheduled Task to run oradim -startup -sid ORCL when the Administrator account logs on, and set the VM to auto-logon. I'd still like to work out why it's not working.

  Read the article

• Cannot connect to local network shares when connected to VPN. Error: "the user name could not be found"

  - by Nick G

  I keep finding that on our small company LAN (7 users, 3 servers) that some servers keep becoming "not accessible" for the purposes of file sharing. They display the message "\SERVER is not accessible. You might not have permission to use this network resource. The user name could not be found". But I don't know why "the user name could not be found" as all the machines are on the same domain and the PDC and BDC seem to be behaving OK. EDIT: VPN seems to be the cause: It turns out I can see the server if I use the IP address (\\1.2.3.4\ etc) or the FQ active directory name (eg \server.domainname.local) but not if I use the server name on its own or a mapped network drive originally created from the "short" name. Oddly though, my machine has no issue resolving the server's DNS name as I can ping the machine name OK and it immediately comes back with the IP, however nslookup seems to fail. It seems to be a problem with how Windows looks up machine names when connected to VPNs. When I'm connected to a VPN, windows seems to use the DNS assocated with the VPN and not the one on the domain controller. This behavior to me, seems incorrect as surely that would mean connecting to any VPN would break any ability to lookup local machine names for servers and printers etc. So I guess the real question now is, how can I make my machine still search the local Active Directory DNS (the PDC) even when connected to a VPN? More info in my comments below.

  Read the article

• Can not join additional domain controllers

  - by Hosm

  Hi all, I had a dead PDC and another not so synced domain controller for my domain. using comments here link now the so called secondary domain controller has seized domain controls and I can verify it from dsa.msc that it is a domain controller. I set up another domain controller (win2003SRV) and about to promote an AD on it as a domain controller for my domain. When I try to join the new domain controller to the domain I face DNS problem. here is some more detail DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain DOMNAME.A.B: The query was for the SRV record for _ldap._tcp.dc._msdcs.DOMNAME.A.B The following domain controllers were identified by the query: update.DOMNAME.A.B Common causes of this error include: - Host (A) records that map the name of the domain controller to its IP addresses are missing or contain incorrect addresses. - Domain controllers registered in DNS are not connected to the network or are not running. For information about correcting this problem, click Help. it is worth noting that update.DOMNAME.A.B is the current domain controller to which I'd like to add another controller named PDC.DOMNAME.A.B Ip address of update.DOMNAME.A.B is 192.168.200.1 and for pdc.DOMNAME.A.B is 192.168.200.100 querying DNS on both machine return correct results. Any idea?

  Read the article

• Is it possible to shrink the size of an HP Smart Array logical drive?

  - by ewwhite

  I know extension is quite possible using the hpacucli utility, but is there an easy way to reduce the size of an existing logical drive (not array)? The controller is a P410i in a ProLiant DL360 G6 server. I'd like to reduce logicaldrive 1 from 72GB to 40GB. => ctrl all show config detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: 5001438006FD9A50 Cache Serial Number: PAAVP9VYFB8Y RAID 6 (ADG) Status: Disabled Controller Status: OK Chassis Slot: Hardware Revision: Rev C Firmware Version: 3.66 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Queue Depth: Automatic Monitor and Performance Delay: 60 min Elevator Sort: Enabled Degraded Performance Optimization: Disabled Inconsistency Repair Policy: Disabled Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Enabled Total Cache Size: 512 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 412476 MB Status: OK Logical Drive: 1 Size: 72.0 GB Fault Tolerance: RAID 1+0 Heads: 255 Sectors Per Track: 32 Cylinders: 18504 Strip Size: 256 KB Status: OK Array Accelerator: Enabled Unique Identifier: 600508B1001C132E4BBDFAA6DAD13DA3 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 196 MB, / 12.0 GB, /usr 8.0 GB, /var 4.0 GB, /tmp 2.0 GB OS Status: LOCKED Logical Drive Label: AE438D6A5001438006FD9A50BE0A Mirror Group 0: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 146 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 146 GB, OK) SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 Device Number: 250 Firmware Version: RevC WWID: 5001438006FD9A5F Vendor ID: PMCSIERA Model: SRC 8x6G

  Read the article

• How do I force Windows 7 to recognize my Projector?

  - by user63564

  I have a new Dell XPS with an NVIDIA GeForce GT 445M and an old (several years) Epson PowerLite Cinema 550 projector. Windows 7 refuses to recognize that the projector is connected under normal conditions (I'll get to the strange condition in a moment). Here are some things that I have already tried: Confirm that the projector continues to work well on my old Windows XP laptop. Confirm that the video cable (HDMI to HDMI) is connected Make sure the Dell laptop is plugged in to wall power at all times Reboot both the computer and the projector Click "Detect" under the "Connect to an External Display" Windows dialog (no reaction) Click "Rigorous Display Detection" under NVIDIA Control Panel (dialog: none found) Checked "Force Television Detection on startup" under "My display is not shown..." in NVIDIA Control Panel (no effect) Here's where it gets weird... My projector has three states: off, standby and on. Standby means the power switch on the back is on, but the projector is effectively off (no picture, no access to menu or controls). When I plug in the HDMI cable while the projector is in standby, Windows detects the projector! It lets me switch to Duplicate, Extend, or Project Only mode, and adjusts the resolution appropriately. A new Generic Plug-n-Play monitor shows up in my device manager. A "Seiko EPSON PJ" display shows up in my NVIDIA control panel. Then if I turn my projector on, Windows no longer recognizes the display. This is true whether I turn the projector on while the HDMI cable is plugged in, or if I unplug the HDMI cable while turning on the projector. Anyone have any ideas, because I'm completely stumped...?

  Read the article

• Backup program for Windows using non-proprietary format?

  - by Cristi Diaconescu

  I'm looking at the various local backup programs for windows, and I was wondering which of them use a non-proprietary backup format? By non-proprietary, I mean I want to be able to access at least the latest version of the backed up files either directly, or by using an open-standard format like zip/7z/rdiff... The other thing I'm looking for in a backup program is the ability to create incremental backups. What I have found so far: SyncBack copies files as-is, using separate directories for versioning pretty much the same for all the 'roll you own' task scheduler + rsync/xcopy32/robocopy/MS SyncToy/etc solutions GFI Backup appears to be using Zip files, at least in their 'Business' version, not sure about the free 'Home' version. Didn't try it yet, but it's next on my list. Mozy (!) supports local backup starting with v 2.0 and basically provides a 2nd local copy on a separate partition. Subjectively, it feels slow and resource intensive (I think it took more than a week to finish the first local backup of ~ 300 GB), and does not appear to offer file versioning (arguably, you can get older file versions online). On the positive side, it looks like the local backup is integrated in the restore process which was traditionally a masochistic experience (and this goes for any online backup provider). Other suggestions? I favor ease of use over tons of options (e.g. SyncBack is very flexible but it offers sooo many ways to shoot yourself in the foot...)

  Read the article

• Building new computer, turns on, but no post

  - by addybojangles

  Pardon my ignorance here, finally decided to put together a computer and egads. I purchased a new motherboard, power supply, processor, video card and memory. ASUS M4A79XTD EVO AM3 AMD 790X ATX AMD Motherboard OCZ Fatal1ty OCZ550FTY 550W ATX12V v2.2 / EPS12V SLI Ready 80 PLUS Certified Modular Active PFC Power Supply AMD Phenom II X4 965 Black Edition Deneb 3.4GHz 4 x 512KB L2 Cache 6MB L3 Cache Socket AM3 125W Quad-Core Processor XFX HD-577A-ZNFC Radeon HD 5770 (Juniper XT) 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Ready CrossFireX Support Video Card G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ (originally had links for you guys, but I lack the rep, sorry!!) And I've got it all in the tower. I put in power supply, installed processor on motherboard, installed heatsink, put in ram, and I am using an older IDE hard disk. When I start the computer, the monitor tells me "check signal cable." As far as I can tell, the heatsink on the processor is spinning, the power supply is on (obviously), and the green LED on the motherboard is on. I originally only had the bigger output plugged in to the motherboard (what I saw in a YouTube vid as well as the mobo instructions), but after doing some research, it said plug in the other ATX power supply. Which I did. And trying to power the computer results in nothing. No beeps on startup, no post, anyone have any ideas? Your ideas and help is greatly appreciated.

  Read the article

< Previous Page | 354 355 356 357 358 359 360 361 362 363 364 365  | Next Page >