Search Results

Search found 18244 results on 730 pages for 'controller action'.

Page 36/730 | < Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

• Bad disk performance on HP DL360 with Smarty Array P400i RAID controller

  - by sarge

  I have a HP DL360 server with 4x 146GB SAS disks and a Smart Array P400i RAID controller with 256MB cache. The disks are in RAID 5 (3 disks + 1 hot spare). The server is running VMware ESX 3i. The disk write performance is really bad. Here are some numbers: ns1:~# hdparm -tT /dev/sda /dev/sda: Timing cached reads: 3364 MB in 2.00 seconds = 1685.69 MB/sec Timing buffered disk reads: 18 MB in 3.79 seconds = 4.75 MB/sec ns1:~# time sh -c "dd if=/dev/zero of=ddfile bs=8k count=125000 && sync" 125000+0 records in 125000+0 records out 1024000000 bytes (1.0 GB) copied, 282.307 s, 3.6 MB/s real 4m52.003s user 0m2.160s sys 3m10.796s Compared to another server those number are terrible: Dell R200, 2x 500GB SATA disks, PERC raid controller (disks are mirrored). web4:~# hdparm -tT /dev/sda /dev/sda: Timing cached reads: 6584 MB in 2.00 seconds = 3297.79 MB/sec Timing buffered disk reads: 316 MB in 3.02 seconds = 104.79 MB/sec web4:~# time sh -c "dd if=/dev/zero of=ddfile bs=8k count=125000 && sync" 125000+0 records in 125000+0 records out 1024000000 bytes (1.0 GB) copied, 35.2919 s, 29.0 MB/s real 0m36.570s user 0m0.476s sys 0m32.298s The server isn't very loaded and the VMware Infrastructure Client performance monitor is showing 550KBps average read and 1208KBps average write for the last 30 minutes (highest write rate: 6.6MBps). This has been a problem from the start. Any ideas?

  Read the article

• Windows 2003 Domain Controller Very Upset about NIC Teaming

  - by Kyle Brandt

  I set up BACS (Broadcom Teaming) to team two NIC on a Windows 2003 Active Directory Domain Controller. Networking still works okay, I can ping the gateway etc, but both DNS and Active Directory fail to start with various 40xx errors. The team that I created is Smart load Balancing with Failover, with one backup and only one in smart load balancing (So really it is just failover). I have the team the same IP address that the single active NIC had before. Anyone seen this before, or have any ideas what the problem might be? Event Type: Error Event Source: DNS Event Category: None Event ID: 4015 Date: 3/7/2010 Time: 10:33:03 AM User: N/A Computer: ADC Description: The DNS server has encountered a critical error from the Active Directory. Check that the Active Directory is functioning properly. The extended error debug information (which may be empty) is "". The event data contains the error. Event Type: Error Event Source: DNS Event Category: None Event ID: 4004 Date: 3/7/2010 Time: 10:33:03 AM User: N/A Computer: ADC Description: The DNS server was unable to complete directory service enumeration of zone .. This DNS server is configured to use information obtained from Active Directory for this zone and is unable to load the zone without it. Check that the Active Directory is functioning properly and repeat enumeration of the zone. The extended error debug information (which may be empty) is "". The event data contains the error. Event Type: Error Event Source: NTDS Replication Event Category: DS RPC Client Event ID: 2087 Date: 3/7/2010 Time: 10:40:28 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: ADC Description: Active Directory could not resolve the following DNS host name of the source domain controller to an IP address. This error prevents additions, deletions and changes in Active Directory from replicating between one or more domain controllers in the forest. Security groups, group policy, users and computers and their passwords will be inconsistent between domain controllers until this error is resolved, potentially affecting logon authentication and access to network resources.

  Read the article

• Red Hat 5.3 on HP Proliant DL380 G5 and failed drive on RAID controller

  - by thinkdreams

  I have a development ERP server here in my office that I assist with support on, and originally the DBA requested a single drive setup for some of the drives on the server. Thus the hardware RAID controller (an HP embedded controller) looks like: c0d0 (2 drive) RAID-1 c0d1 (2 drive) RAID-1 c0d2 (1 drive) No RAID <-- Failed c0d3 (1 drive) No RAID c0d4 (1 drive) No RAID c0d5 (1 drive) No RAID c0d2 has failed. I replaced the drive immediately with a spare using the hot-swap, but the c0d2 continues to mark itself as failed, even when I umount the partition. I'm loathe to reboot the server since I'm concerned about the server coming back up in rescue mode but I'm afraid that's the only way to get the system to re-read the drive. I assumed there was some sort of auto-detection routine for this, but I haven't been able to figure out the proper procedure. I have installed the HP ACU CLI utilties, so I can see the hardware RAID setup. I'd really like to find out what the proper procedure should have been, where I went wrong, and how to correct it now. Obviously this goes without saying I should NOT have listened to the DBA and set the drives up as RAID-1 throughout as was my first instinct. He wasn't worried about data loss, but it sure would have been easier to replace the failed drive. :)

  Read the article

• Slow parity initialization of RAID-5 array on HP Smart Array 411 controller

  - by Rob Nicholson

  On 29th October 2011, I built a RAID-5 array using 4 x 146.8GB Seagate SAS ST3146855SS drives running at 15k connected to a PowerEdge R515 with HP Smart Array P411 controller running Windows 2008 (so nothing particularly unusual). I know that parity initialisation of a RAID-5 array can take some time but it's still running after 2.5 weeks which seems a little unusual. I'd previously built another array on the same controller using 4 x 2TB SATA-2 drives and that did take a while to complete but a) I'm sure it was less than 2.5 weeks, b) that array was ~12 times bigger and c) during initialization, the percentrage slowly increased each day. At the moment, the status display for this new 2nd array simply says "Parity Initialization Status: In Progress" and it's said that since the start. It's this lack of change on the status that worries me the most - feels like it's not actually doing anything. Do you think something has gone wrong or am I being unpatient and for some reason, the status not increasing is normal? I kind of expected a much smaller array on faster drives (15k SAS versus 7.5k SATA-2) to build in a few days. This is our primary SAN running StarWind so my "have a play" options are very limited. This 2nd array is currently in use for one small virtual disk so I could shut the target machine down, move the virtual disk to another drive and try rebuilding.

  Read the article

• Using smartctl to get vendor specific Attributes from ssd drive behind a SmartArray P410 controller

  - by Lairsdragon

  Recently I have deployed some HP server with SSD's behind a SmartArray P410 controller. While not official supported from HP the server work well sofar. Now I like to get wear level info's, error statistics etc from the drive. While the SA P410 supports a passthru of the SMART Command to a single drive in the array the output I was not able to the the interesting things from the drive. In this case especially the value the Wear level indicator is from interest for me (Attr.ID 233), but this is ony present if the drive is directly attanched to a SATA Controller. smartctl on directly connected ssd: # smartctl -A /dev/sda smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0000 100 000 000 Old_age Offline In_the_past 0 4 Start_Stop_Count 0x0000 100 000 000 Old_age Offline In_the_past 0 5 Reallocated_Sector_Ct 0x0002 100 100 000 Old_age Always - 0 9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 8561 12 Power_Cycle_Count 0x0002 100 100 000 Old_age Always - 55 192 Power-Off_Retract_Count 0x0002 100 100 000 Old_age Always - 29 232 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 0 233 Unknown_Attribute 0x0002 088 088 000 Old_age Always - 0 225 Load_Cycle_Count 0x0000 198 198 000 Old_age Offline - 508509 226 Load-in_Time 0x0002 255 000 000 Old_age Always In_the_past 0 227 Torq-amp_Count 0x0002 000 000 000 Old_age Always FAILING_NOW 0 228 Power-off_Retract_Count 0x0002 000 000 000 Old_age Always FAILING_NOW 0 smartctl on P410 connected ssd: # ./smartctl -A -d cciss,0 /dev/cciss/c1d0 smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net (Right, it is complety empty) smartctl on P410 connected hdd: # ./smartctl -A -d cciss,0 /dev/cciss/c0d0 smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Current Drive Temperature: 27 C Drive Trip Temperature: 68 C Vendor (Seagate) cache information Blocks sent to initiator = 1871654030 Blocks received from initiator = 1360012929 Blocks read from cache and sent to initiator = 2178203797 Number of read and write commands whose size <= segment size = 46052239 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 3363.25 number of minutes until next internal SMART test = 12 Do I hunt here a bug, or is this a limitation of the p410 SMART cmd Passthru?

  Read the article

• 550 Requested action not taken: mailbox unavailable

  - by Porch

  I setup a small box with Server 2003 64bit to be used as a webserver and email server for a small school. Real simple stuff for a few users. A simple website and a handful of emails. rDNS and spf records setup and pass every test I found including test at dnsstuff.com. Email sending to almost every email address (google, hotmail, aol, whatever) works. However, with one domain, I get an bounce back with the error. 550 Requested action not taken: mailbox unavailable It's another school running Exchange judging from some packet sniffing with WireShark. Every email on this domain I have tried sending to gives this error. The email address is valid as I can send to it from my personal, and gmail account without a problem. Does anyone know of some anti-spam software that gives an 550 error like the above? What else could this be? Thanks for any suggestions. Packet capture of the two servers communicating look like this. 220 <server snip> Microsoft ESMTP MAIL Service, Version: 6.0.3790.3959 ready at Sat, 2 Oct 2010 12:48:17 -0700 EHLO <email snip> 250-<server snip> Hello [<ip snip>] 250-TURN 250-SIZE 250-ETRN 250-XXXXXXXXXX 250-DSN 250-ENHANCEDSTATUSCODES 250-8bitmime 250-BINARYMIME 250-XXXXXXXX 250-VRFY 250-X-EXPS GSSAPI NTLM LOGIN 250-X-EXPS=LOGIN 250-AUTH GSSAPI NTLM LOGIN 250-AUTH=LOGIN 250-X-LINK2STATE 250-XXXXXXX 250 OK MAIL FROM: <email snip> 250 2.1.0 <email snip>....Sender OK RCPT TO:<email snip> 250 2.1.5 <email snip> DATA 354 Start mail input; end with <CRLF>.<CRLF> <email body here> . 550 Requested action not taken: mailbox unavailable QUIT 221 Goodbye

  Read the article

• how to initialize two logical drives on a HP P400i controller without reboot

  - by John

  What I am trying to do is initialize two logical drives on a HP P400i embedded controller without a reboot of the system here my current Array config: array A (SAS, Unused Space: 0 MB) logicaldrive 1 (17.9 GB, RAID 5, OK) logicaldrive 2 (17.9 GB, RAID 5, OK) logicaldrive 3 (75.9 GB, RAID 5, OK) logicaldrive 4 (25.0 GB, RAID 5, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 72 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 72 GB, OK) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 72 GB, OK) array B (SAS, Unused Space: 0 MB) logicaldrive 5 (99 MB, RAID 0, OK) logicaldrive 6 (68.2 GB, RAID 0, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 72 GB, OK) windows 2003 machine running the HpCISs2.sys driver version 6.20.0.32 . I have the ACU and ACU CLI tools installed version 8.28.13.0, P400i firmware version 2.74 . Now what I'd like to do is removes the physical drive 1I:1:4 and delete the two logical drives in array B. then insert a new drive in to bay 4 that contains two new logical drives and have them show up in array B again. So far after I remove the drive and delete the failed logical drives, I insert the new drive and run HPacucli rescan. I get the new drive to show up as unassinged physical drive but I cant figure out now to "for lack of a better word" mount the 2 logical drives on the new unassinged disk. If I reboot the system the array controller picks up the new fourth drive and creates Array B with the drives without problem but I'd really like to not have to reboot the server. Any ideas?

  Read the article

• Domain Controller DNS Best Practice/Practical Considerations for Domain Controllers in Child Domains

  - by joeqwerty

  I'm setting up several child domains in an existing Active Directory forest and I'm looking for some conventional wisdom/best practice guidance for configuring both DNS client settings on the child domain controllers and for the DNS zone replication scope. Assuming a single domain controller in each domain and assuming that each DC is also the DNS server for the domain (for simplicity's sake) should the child domain controller point to itself for DNS only or should it point to some combination (primary VS. secondary) of itself and the DNS server in the parent or root domain? If a parentchildgrandchild domain hierarchy exists (with a contiguous DNS namespace) how should DNS be configured on the grandchild DC? Regarding the DNS zone replication scope, if storing each domain's DNS zone on all DNS servers in the domain then I'm assuming a DNS delegation from the parent to the child needs to exist and that a forwarder from the child to the parent needs to exist. With a parentchildgrandchild domain hierarchy then does each child forward to the direct parent for the direct parent's zone or to the root zone? Does the delegation occur at the direct parent zone or from the root zone? If storing all DNS zones on all DNS servers in the forest does it make the above questions regarding the replication scope moot? Does the replication scope have some bearing on the DNS client settings on each DC?

  Read the article

• Linux - real-world hardware RAID controller tuning (scsi and cciss)

  - by ewwhite

  Most of the Linux systems I manage feature hardware RAID controllers (mostly HP Smart Array). They're all running RHEL or CentOS. I'm looking for real-world tunables to help optimize performance for setups that incorporate hardware RAID controllers with SAS disks (Smart Array, Perc, LSI, etc.) and battery-backed or flash-backed cache. Assume RAID 1+0 and multiple spindles (4+ disks). I spend a considerable amount of time tuning Linux network settings for low-latency and financial trading applications. But many of those options are well-documented (changing send/receive buffers, modifying TCP window settings, etc.). What are engineers doing on the storage side? Historically, I've made changes to the I/O scheduling elevator, recently opting for the deadline and noop schedulers to improve performance within my applications. As RHEL versions have progressed, I've also noticed that the compiled-in defaults for SCSI and CCISS block devices have changed as well. This has had an impact on the recommended storage subsystem settings over time. However, it's been awhile since I've seen any clear recommendations. And I know that the OS defaults aren't optimal. For example, it seems that the default read-ahead buffer of 128kb is extremely small for a deployment on server-class hardware. The following articles explore the performance impact of changing read-ahead cache and nr_requests values on the block queues. http://zackreed.me/articles/54-hp-smart-array-p410-controller-tuning http://www.overclock.net/t/515068/tuning-a-hp-smart-array-p400-with-linux-why-tuning-really-matters http://yoshinorimatsunobu.blogspot.com/2009/04/linux-io-scheduler-queue-size-and.html For example, these are suggested changes for an HP Smart Array RAID controller: echo "noop" > /sys/block/cciss\!c0d0/queue/scheduler blockdev --setra 65536 /dev/cciss/c0d0 echo 512 > /sys/block/cciss\!c0d0/queue/nr_requests echo 2048 > /sys/block/cciss\!c0d0/queue/read_ahead_kb What else can be reliably tuned to improve storage performance? I'm specifically looking for sysctl and sysfs options in production scenarios.

  Read the article

• pxe boot dos 7.x / 8.x on modern mainboard without floppy controller

  - by GitaarLAB

  How to pxe boot MS DOS 7.x / 8.x on a modern pc (mainboard without floppy controller) without using an external usb floppy drive? MS DOS 6.22 and earlier or other flavors pxe boot just fine on floppy-less hardware. But DOS 7.x and 8.x renders an error on boot: "Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) I read somewhere during research this was a rather unknown error, that started to become more common due to the advent of floppy-controller-less hardware. On some hardware (bios dependent) one could plug a usb-floppy-drive in the computer before booting (but that MIGHT also require it to be a "golden floppy drive" (as they where called back then). From a russian site (I read about a year ago and cannot find the hyperlink) MS-Dos versions 6.22 did some-kind of floppy-drive reset during initialization and since it couldn't connect to the floppy-host thus the error. How can I resolve this (without a physical external usb floppy)? Might there be some kind of virtual floppy-driver that could resolve this (for example to be loaded before the dos image loads)? Or could someone point me into the right direction (maybe even a hex-address and some further explanation or something)? I'm using syslinux by the way.

  Read the article

• Restricting access to one controller of an MVC app with Nginx

  - by kgb

  I have an MVC app where one controller needs to be accessible only from several ips(this controller is an oauth token callback trap - for google/fb api tokens). My conf looks like this: geo $oauth { default 0; 87.240.156.0/24 1; 87.240.131.0/24 1; } server { listen 80; server_name some.server.name.tld default_server; root /home/user/path; index index.php; location /oauth { deny all; if ($oauth) { rewrite ^(.*)$ /index.php last; } } location / { if ($request_filename !~ "\.(phtml|html|htm|jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js|xlsx)$") { rewrite ^(.*)$ /index.php last; break; } } location ~ \.php$ { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } } It works, but does not look right. The following seems logical to me: location /oauth { allow 87.240.156.0/24; deny all; rewrite ^(.*)$ /index.php last; } But this way rewrite happens all the time, allow and deny directives are ignored. I don't understand why...

  Read the article

• Cannot access Domain Controller through VPN

  - by Markus

  In our small network there is a Windows 2008 R2 Domain Controller that also serves as Remote Access Server. For years, we could access this server and the resources in the network over a VPN connection without any problem. Since some time however, I am able to connect to the VPN, but my Windows 8 client (and another one I used for testing purposes) is not able to connect the domain controller afterwards. I can access any other server in the network, but there seems to be a problem regarding the trust between the client(s) and the server. If I connect the client to the network directly over a LAN cable, everything works as expected. Also I can connect to another server over VPN and open a RDP prompt to the DC without a problem. On the client, whenever I try to access the DC, I get an access denied message. I've tried to update the group policies both over VPN and LAN. Also, I've removed the client from the domain and re-added it. The client shows a message that Windows requires valid login information when connected to the VPN - but my credentials are valid. They work when I logon to the client when not connected to the VPN and also when connected to the LAN. Turning off the firewall on the client and the server did not change anything. DNS resolution works both on the server and the client. What else can I do to diagnose and solve the problem?

  Read the article

• iPad issue with a modal view: modal view label null after view controller is created

  - by iPhone Guy

  This is a weird issue. I have created a view controller with a nib file for my modal view. On that view there is a label, number and text view. When I create the view from the source view, I tried to set the label, but it shows that the label is null (0x0). Kinda weird... Any suggestions? Now lets look at the code (I put all of the code here because that shows more than I can just explain): The modal view controller - in IB the label is connected to the UILabel object: @implementation ModalViewController @synthesize delegate; @synthesize goalLabel, goalText, goalNumber; // Done button clicked - (void)dismissView:(id)sender { // Call the delegate to dismiss the modal view if ([delegate respondsToSelector:@selector(didDismissModalView: newText:)]) { NSNumber *tmpNum = goalNumber; NSString *tmpString = [[NSString alloc] initWithString:[goalText text]]; [delegate didDismissModalView:tmpNum newText:tmpString]; [tmpNum release]; [tmpString release]; } } - (void)cancelView:(id)sender { // Call the delegate to dismiss the modal view if ([delegate respondsToSelector:@selector(didCancelModalView)]) [delegate didCancelModalView]; } -(void) setLabelText:(NSString *)text { [goalLabel setText:text]; } /* // The designated initializer. Override if you create the controller programmatically and want to perform customization that is not appropriate for viewDidLoad. - (id)initWithNibName:(NSString *)nibNameOrNil bundle:(NSBundle *)nibBundleOrNil { if ((self = [super initWithNibName:nibNameOrNil bundle:nibBundleOrNil])) { // Custom initialization } return self; } */ -(void) viewWillAppear:(BOOL)animated { [super viewWillAppear:animated]; // bring up the keyboard.... [goalText becomeFirstResponder]; } // Implement viewDidLoad to do additional setup after loading the view, typically from a nib. - (void)viewDidLoad { [super viewDidLoad]; // set the current goal number to -1 so we know none was set goalNumber = [NSNumber numberWithInt: -1]; // Override the right button to show a Done button // which is used to dismiss the modal view self.navigationItem.rightBarButtonItem = [[[UIBarButtonItem alloc] initWithBarButtonSystemItem:UIBarButtonSystemItemDone target:self action:@selector(dismissView:)] autorelease]; // and now for the cancel button self.navigationItem.leftBarButtonItem = [[[UIBarButtonItem alloc] initWithBarButtonSystemItem:UIBarButtonSystemItemCancel target:self action:@selector(cancelView:)] autorelease]; self.navigationItem.title = @"Add/Update Goals"; } - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { // Overriden to allow any orientation. return YES; } - (void)didReceiveMemoryWarning { // Releases the view if it doesn't have a superview. [super didReceiveMemoryWarning]; // Release any cached data, images, etc that aren't in use. } - (void)viewDidUnload { [super viewDidUnload]; // Release any retained subviews of the main view. // e.g. self.myOutlet = nil; } - (void)dealloc { [super dealloc]; } @end And here is where the view controller is created, variables set, and displayed: - (void)tableView:(UITableView *)tableView didSelectRowAtIndexPath:(NSIndexPath *)indexPath { // put a checkmark.... UITableViewCell *tmpCell = [tableView cellForRowAtIndexPath:indexPath]; [tmpCell setAccessoryType:UITableViewCellAccessoryCheckmark]; // this is where the popup is gonna popup! // ===> HEre We Go! // Create the modal view controller ModalViewController *mdvc = [[ModalViewController alloc] initWithNibName:@"ModalDetailView" bundle:nil]; // We are the delegate responsible for dismissing the modal view [mdvc setDelegate:self]; // Create a Navigation controller UINavigationController *navController = [[UINavigationController alloc] initWithRootViewController:mdvc]; // set the modal view type navController.modalPresentationStyle = UIModalPresentationFormSheet; // set the label for all of the goals.... if (indexPath.section == 0 && indexPath.row == 0) { [mdvc setLabelText:[[[NSString alloc] initWithString:@"Long Term Goal 1:"] autorelease]]; [mdvc setGoalNumber:[NSNumber numberWithInt:1]]; } if (indexPath.section == 0 && indexPath.row == 1) { [mdvc setLabelText:[[[NSString alloc] initWithString:@"Long Term Goal 2:"] autorelease]]; [mdvc setGoalNumber:[NSNumber numberWithInt:2]]; } if (indexPath.section == 0 && indexPath.row == 2) { [mdvc setLabelText:[[[NSString alloc] initWithString:@"Long Term Goal 3:"] autorelease]]; [mdvc setGoalNumber:[NSNumber numberWithInt:3]]; } if (indexPath.section == 0 && indexPath.row == 3) { [mdvc setLabelText:[[[NSString alloc] initWithString:@"Long Term Goal 4:"] autorelease]]; [mdvc setGoalNumber:[NSNumber numberWithInt:4]]; } if (indexPath.section == 1 && indexPath.row == 0) { [mdvc setLabelText:[[[NSString alloc] initWithString:@"Short Term Goal 1:"] autorelease]]; [mdvc setGoalNumber:[NSNumber numberWithInt:5]]; } if (indexPath.section == 1 && indexPath.row == 1) { [mdvc setLabelText:[[[NSString alloc] initWithString:@"Short Term Goal 2:"] autorelease]]; [mdvc setGoalNumber:[NSNumber numberWithInt:6]]; } if (indexPath.section == 1 && indexPath.row == 2) { [mdvc setLabelText:[[[NSString alloc] initWithString:@"Short Term Goal 3:"] autorelease]]; [mdvc setGoalNumber:[NSNumber numberWithInt:7]]; } if (indexPath.section == 1 && indexPath.row == 3) { [mdvc setLabelText:[[[NSString alloc] initWithString:@"Short Term Goal 4:"] autorelease]]; [mdvc setGoalNumber:[NSNumber numberWithInt:8]]; } // show the navigation controller modally [self presentModalViewController:navController animated:YES]; // Clean up resources [navController release]; [mdvc release]; // ==> Ah... we are done... }

  Read the article

• Artec TV18R Tuner not working :(

  - by Antillar Maximus

  Can somebody kindly help me setup my TV Tuner stick? Make and Model: Artec TV18R USB TV Tuner OS: Ubuntu 11.10 64bit Hardware: MSI MS1656-US (GX640 barebones): i5 580M, 2xIntel X25M SSDs, Radeon HD5850M,Realtek sound. Logs and messages: antillar@antillar-MS-1656:/usr/share/dvb/atsc$ [B][COLOR=Red]sudo lsusb[/COLOR][/B] Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 003: ID ffc0:001f Bus 002 Device 005: ID 05d8:8117 Ultima Electronics Corp. [/code][code]antillar@antillar-MS-1656:/usr/share/dvb/atsc$ So, it seems that the tuner is being detected, but the light on it does not turn on? Not sure what is going on? sudo lspci [sudo] password for antillar: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 05) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 01:00.0 VGA compatible controller: ATI Technologies Inc Broadway PRO [Mobility Radeon HD 5800 Series] 01:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 04:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller 04:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller 04:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller 04:00.3 System peripheral: JMicron Technology Corp. MS Host Controller 04:00.4 System peripheral: JMicron Technology Corp. xD Host Controller 05:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) antillar@antillar-MS-1656:/usr/share/dvb/atsc$ I have been searching for a solution to this all weekend without any luck. I remember reading that ehci_hcd is the problem, but I'm not sure if disabling it is a good idea. I don't want my USB ports to go back to v1.1. Thank you!

  Read the article

• Struts 2- problem with s:action tag

  - by Raghave

  Here is a small test application that does following things ask user to enter his name and submit - (index.jsp) as a result of index.jsp is the welcome.jsp page that asks user to select his/her blood group index.jsp <%@ page language="java" import="java.util.*" pageEncoding="ISO-8859-1"%> <%@ taglib prefix="s" uri="/struts-tags" %> <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> </head> <body> <form action="MyName"> <s:textfield name="UserName" label="Enter Your Name"/> <s:submit/> </form><br> </body> </html> struts.xml <?xml version="1.0" encoding="UTF-8" ?> <!DOCTYPE struts PUBLIC "-//Apache Software Foundation//DTD Struts Configuration 2.1//EN" "http://struts.apache.org/dtds/struts-2.1.dtd"> <struts> <package name="module1" namespace="" extends="struts-default"> <action name="MyName" class="module1.User"> <result>/Welcome.jsp</result> </action> <action name="Blood_Group" class="module1.SelectBloodGroup" method="bloodGroupList"/> </package> </struts> SelectBloodGroup.java package module1; import java.util.ArrayList; import com.opensymphony.xwork2.ActionSupport; public class SelectBloodGroup extends ActionSupport{ private ArrayList<BloodGroup> bglist; public String bloodGroupList(){ bglist = new ArrayList<BloodGroup>(); bglist.add(new BloodGroup("1","A+")); bglist.add(new BloodGroup("2","B+")); bglist.add(new BloodGroup("3","AB+")); bglist.add(new BloodGroup("4","O+")); bglist.add(new BloodGroup("5","A-")); bglist.add(new BloodGroup("6","B-")); bglist.add(new BloodGroup("7","AB-")); bglist.add(new BloodGroup("8","O-")); return "SUCCESS"; } public ArrayList<BloodGroup> getBglist(){ return bglist; } } class BloodGroup{ private String id; private String bg; BloodGroup(String id,String bg){ this.id=id; this.bg=bg; } } welcome.jsp <%@ page language="java" import="java.util.*" pageEncoding="ISO-8859-1"%> <%@ taglib prefix="s" uri="/struts-tags" %> <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> </head> <body> <s:action name="Blood_Group" executeResult="false"/> //***************here is the problem*************** <s:select list="bglist" listKey="id" listValue="bg"/> //*********************************************** </body> </html> Struts is unable to identify bglist as a collection or Array or List or iterator. WHAT SHOULD I ASSIGN TO list ATTRIBUTE IN THE s:select TAG IN THE FILE welcome.jsp What is wrong with the code please tell me in detail. If you could send me the correted version. WHY IS THE s:action Tag not working ? This is the error i am getting Apr 13, 2010 1:49:19 PM org.apache.catalina.core.ApplicationDispatcher invoke SEVERE: Servlet.service() for servlet jsp threw exception tag 'select', field 'list': The requested list key 'bglist' could not be resolved as a collection/array/map/enumeration/iterator type. Example: people or people.{name} - [unknown location]

  Read the article

• Video quality too bad while playing (any) videos in Intel GM965/GL960 Integrated Graphics Controller Ubuntu 12.04

  - by Sukhdev

  I have searched blogs and forums, installed several drivers, but can't find a solution that can provide equivalent video quality as that of Windows 7. Kindly help. Video quality specially color is too bad while playing with any media player. Configuration details are: Ubuntu - 12.04 Intel Corporation Mobile GM965/GL960 Integrated The results of the following commands are a) sudo lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c) b) find /dev -group video /dev/fb0 /dev/dri/card0 /dev/dri/controlD64 /dev/agpgart c) glxinfo | grep -i vendor server glx vendor string: SGI client glx vendor string: ATI OpenGL vendor string: Tungsten Graphics, Inc d) sudo lshw -C video *-display:0 description: VGA compatible controller product: Mobile GM965/GL960 Integrated Graphics Controller (primary) vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 0c width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:fea00000-feafffff memory:e0000000-efffffff ioport:efe8(size=8) *-display:1 UNCLAIMED description: Display controller product: Mobile GM965/GL960 Integrated Graphics Controller (secondary) vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 0c width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: latency=0 resources: memory:feb00000-febfffff I have spent days installing various drivers, and then un-installing but can't come up with a solution. Please help.

  Read the article

• DRY-ing very similar specs for ASP.NET MVC controller action with MSpec (BDD guidelines)

  - by spapaseit

  Hi all, I have two very similar specs for two very similar controller actions: VoteUp(int id) and VoteDown(int id). These methods allow a user to vote a post up or down; kinda like the vote up/down functionality for StackOverflow questions. The specs are: VoteDown: [Subject(typeof(SomeController))] public class When_user_clicks_the_vote_down_button_on_a_post : SomeControllerContext { Establish context = () => { post = PostFakes.VanillaPost(); post.Votes = 10; session.Setup(s => s.Single(Moq.It.IsAny<Expression<Func<Post, bool>>>())).Returns(post); session.Setup(s => s.CommitChanges()); }; Because of = () => result = controller.VoteDown(1); It should_decrement_the_votes_of_the_post_by_1 = () => suggestion.Votes.ShouldEqual(9); It should_not_let_the_user_vote_more_than_once; } VoteUp: [Subject(typeof(SomeController))] public class When_user_clicks_the_vote_down_button_on_a_post : SomeControllerContext { Establish context = () => { post = PostFakes.VanillaPost(); post.Votes = 0; session.Setup(s => s.Single(Moq.It.IsAny<Expression<Func<Post, bool>>>())).Returns(post); session.Setup(s => s.CommitChanges()); }; Because of = () => result = controller.VoteUp(1); It should_increment_the_votes_of_the_post_by_1 = () => suggestion.Votes.ShouldEqual(1); It should_not_let_the_user_vote_more_than_once; } So I have two questions: How should I go about DRY-ing these two specs? Is it even advisable or should I actually have one spec per controller action? I know I Normally should, but this feels like repeating myself a lot. Is there any way to implement the second It within the same spec? Note that the It should_not_let_the_user_vote_more_than_once; requires me the spec to call controller.VoteDown(1) twice. I know the easiest would be to create a separate spec for it too, but it'd be copying and pasting the same code yet again... I'm still getting the hang of BDD (and MSpec) and many times it is not clear which way I should go, or what the best practices or guidelines for BDD are. Any help would be appreciated.

  Read the article

• How can I inherit an ASP.NET MVC controller and change only the view?

  - by AlexWalker

  I have a controller that's inheriting from a base controller, and I'm wondering how I can utilize all of the logic from the base controller, but return a different view than the base controller uses. The base controller populates a model object and passes that model object to its view, but I'm not sure how I can access that model object in the child controller so that I can pass it to the child controller's view.

  Read the article

• Performance - FunctionCall vs Event vs Action vs Delegate

  - by hwcverwe

  Currently I am using Microsoft Sync Framework to synchronize databases. I need to gather information per record which is inserted/updated/deleted by Microsoft Sync Framework and do something with this information. The sync speed can go over 50.000 records per minute. So that means my additional code need to be very lightweight otherwise it will be a huge performance penalty. Microsoft Sync Framework raises an SyncProgress event for each record. I am subscribed to that code like this: // Assembly1 SyncProvider.SyncProgress += OnSyncProgress; // .... private void OnSyncProgress(object sender, DbSyncProgressEventArgs e) { switch (args.Stage) { case DbSyncStage.ApplyingInserts: // MethodCall/Delegate/Action<>/EventHandler<> => HandleInsertedRecordInformation // Do something with inserted record info break; case DbSyncStage.ApplyingUpdates: // MethodCall/Delegate/Action<>/EventHandler<> => HandleUpdatedRecordInformation // Do something with updated record info break; case DbSyncStage.ApplyingDeletes: // MethodCall/Delegate/Action<>/EventHandler<> => HandleDeletedRecordInformation // Do something with deleted record info break; } } Somewhere else in another assembly I have three methods: // Assembly2 public class SyncInformation { public void HandleInsertedRecordInformation(...) {...} public void HandleUpdatedRecordInformation(...) {...} public void HandleInsertedRecordInformation(...) {...} } Assembly2 has a reference to Assembly1. So Assembly1 does not know anything about the existence of the SyncInformation class which need to handle the gathered information. So I have the following options to trigger this code: use events and subscribe on it in Assembly2 1.1. EventHandler< 1.2. Action< 1.3. Delegates using dependency injection: public class Assembly2.SyncInformation : Assembly1.ISyncInformation Other? I know the performance depends on: OnSyncProgress switch using a method call, delegate, Action< or EventHandler< Implementation of SyncInformation class I currently don't care about the implementation of the SyncInformation class. I am mainly focused on the OnSyncProgress method and how to call the SyncInformation methods. So my questions are: What is the most efficient approach? What is the most in-efficient approach? Is there a better way than using a switch in OnSyncProgress?

  Read the article

• DNS slow after losing DNS Server

  - by Tim

  We have set up a small Windows Server 2008 R2 network with a domain controller which is also acting as the DNS server for the network (we opted to install DNS when setting up the domain). This network isn't connected to the Internet in any way, so all machines have been configured to use the IP address of the domain controller as their primary DNS and no secondary DNS server has been configured. If we shut down or unplug the network cable from the domain controller, DNS lookups become quite slow and the performance of the network suffers. For example, running a ping command using a hostname takes around 5-6 seconds to resolve the name. I presume this is because it is looking for the DNS, then falling back to some other method of resolving the names as the DNS server is now gone. All the machines have static IP addresses so we are considering just putting all entries in the HOSTS file of each machine. However, it would be nice to have a centralised DNS in case we one day change the IP of one of the machines. Is there a better way to speed this up?

  Read the article

• likewise-open and samba as pdc

  - by Knight Samar

  Hi, We have successfully implemented a Samba Primary Domain Controller for a hybrid Windows-Linux environment. So now I am setting up dual-boot clients with Windows XP and Ubuntu 9.10. Windows XP can be easily added to the Samba Domain. Everything is manageable. No worries. But when I try using likewise-open 4.1 to add the Ubuntu 9.10 to the samba domain, it cannot locate the domain controller. domainjoin-cli --loglevel verbose join MYDOMAIN root Error: Unable to resolve DC name [code 0x00080026] Resolving 'MYDOMAIN' failed. Check that the domain name is correctly entered. Also check that your DNS server is reachable, and that your system is configured to use DNS in nsswitch. I even tried mydomain.com variations but to no avail. What am I missing ? I read up a document on MSDN wherein it says that the Domain Controller creates some SRV records in the DNS server. I guess, I don't have them on my BIND. Do you think that is the problem ? If yes, can anyone please point out how and what SRV records need to be added. Thanks.

  Read the article

• Smart Array P400 battery failure

  - by RobIII

  The P400 Smart Array controller in my HP DL380G5 is indicating: Battery Status: Failed, Replace Battery 1 in the System Management Homepage. Also the IML indicates: POST Error: 1794-Drive Array - Array Accelerator Battery Charge Low I do have several replacement batteries (actually, several controllers including batteries) lying around at work but never had to actually replace one. I am wondering if the battery replacement (swap) could be done hot or if I need to take down my server to do the battery replacement. I have replaced other spare parts like fans and drives before and all those can be replaced hot. I just don't know about the battery of the P400 Smart Array controller. Any help would be appreciated. EDIT1 For those interested: straight from the horse's mouth: With thanks to Frands Hansen pointing it out here. EDIT2 In the end I did just power down, to be on the safe side and because the manual says so, and replace the battery. Couldn't be easier. Unplugged the old one of the end of the cable (not the end connected to the controller) and reconnected a spare one. The replaced battery is now in the server for about an hour and currently (still) recharging. I'm assuming all will end wel.

  Read the article

• Internal and External DNS from Different Servers, Same Zone

  - by Shane

  Hello All, I am either having trouble understanding how DNS works, or I am having trouble configuring my DNS correctly (either one isn't good). I am currently working with a domain, I'll call it webdomain.com, and I need to allow all of our internal users to get out to dotster to get our public DNS entries just like the rest of the world. Then, on top of that, I want to be able to supply just a few override DNS entries for testing servers and equipment that is not available publically. As an example: public.webdomain.com - should get this from dotster outside.webdomain.com - should get this from dotster as well testing.webdomain.com - should get this from my internal dns controller The problem that I seem to be running into at every turn is that if I have an internal DNS controller that contains a zone for webdomain.com then I can get my specified internal entries but never get anything from the public DNS server. This holds true regardless of the type of DNS server I use also--I have tried both a Linux Bind9 and a Windows 2008 Domain Controller. I guess my big question is: am I being unreasonable to think that a system should be able to check my specified internal DNS and in the case where a requested entry doesn't exist it should fail over to the specified public dns server -OR- is this just not the way DNS works and I am lost in the sauce? It seems like it should be as simple as telling my internal DNS server to forward any requests that it can't fulfill to dotster, but that doesn't seem to work. Could this be a firewall issue? Thanks in advance

  Read the article

• dns in a small network with router and AD domain

  - by Felix

  I have a small office network with router (running OpenWRT), Windows Domain Controller (used to be 2008R2; I just backed it up and upgraded to 2012), about a dozen AD clients (3 server and windows workstation) and several non-AD clients (network printer, PBX). The problem is that the clients can't access servers by name (only by IP). I tried all kind of permutations. Right now domain controller runs DNS server for all desktops; but unless I put an entry in hosts file - I can only get by IP. I have router as DHCP server (since not all devices are on AD); and except for Domain Controller all IP addresses, including "static", are assigned by the router. Most frustrating, some servers sometimes just work! for example, I can often get to the Linux box by name (it is part of Domain using Beyond Trust Integration Services); but I can never get to SQL Server box. Seems like non-domain devices see more names than domain members... This network should be fairly typical; but I couldn't get any guidance about how to set up DNS/DHCP service to make all nodes happy. The closest is this question, but still it's different! Thanks

  Read the article

• w2k3 AD DC Demotion fails with "no other AD DC for that domain can be contacted"

  - by Kstro21

  i've a small office with a single w2k3 sp2 DC(bad idea, but it is real), now, i want to make a clean install of that pc, so, i got another one, install w2k3 sp2, add it to the domain, dcpromo and set it to be a GC, untill now everything is ok, then tried to dcpromo in the primary DC, but it fails with The box indicating that this domain controller is the last controller for the domain mydomain.com is unchecked. However, no other Active Directory domain controllers for that domain can be contacted. Do you wish to proceed anyway? If you click Yes, any Active Directory changes that have been made on this domain controller will be lost. So, i started to move all the roles to the new server as described here, when all was ok with the roles, i tried doing the same, but got the same result. Tried moving the DNS to the new server, but it doesn't make difference. Shutdown to the old server, then tried to log into a workstation, but it fails saying the domain is not available, also coudln't add new workstation to the domain, so i have to power on the old server again. So, if i successfully move all the roles and dns to the new server: why dcpromo give such message in the old server? why if i shutdown the old server the domain is not available?? if i successfully move all the roles and dns to the new server, and i click yes when dcpromo give warning in the old server, will i lose all users, computers, ou, etc.? am i missing some steps to make this work?? hope you can help me thanks

  Read the article

< Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >