Search Results

Search found 4415 results on 177 pages for 'dotnetnuke modules'.

Page 36/177 | < Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

• Error building main Guest Additions Module while installing VirtualBox guest additions

  - by Praveen Sripati

  I have installed Ubuntu 12.10 Guest on Ubuntu 12.04 Host using VirtualBox. Everything is from repository and no direct install. When I install the guest additions, the below error is shown in the console. Before running the command I mapped the VBoxGuestAdditions.iso in the Guest. The closest I could get is this article which says to install the latest version of VirtualBox (not the one from the repository). Is there any alternate solution? sudo ./VBoxLinuxAdditions.run Verifying archive integrity... All good. Uncompressing VirtualBox 4.1.12 Guest Additions for Linux......... VirtualBox Guest Additions installer Removing installed version 4.1.12 of VirtualBox Guest Additions... Removing existing VirtualBox DKMS kernel modules ...done. Removing existing VirtualBox non-DKMS kernel modules ...done. Building the VirtualBox Guest Additions kernel modules The headers for the current running kernel were not found. If the following module compilation fails then this could be the reason. Building the main Guest Additions module ...fail! (Look at /var/log/vboxadd-install.log to find out what went wrong) Doing non-kernel setup of the Guest Additions ...done. Installing the Window System drivers Warning: unknown version of the X Window System installed. Not installing X Window System drivers. Installing modules ...done. Installing graphics libraries and desktop services components ...done.

  Read the article

• NetBeans Sources as a Platform

  - by Geertjan

  By default, when you create a new NetBeans module, the 'development IDE' is the platform to which you'll be deploying your module. It's a good idea to create your own platform and check that into your own repo, so that everyone working on your project will be able to work with a standardized platform, rather than whatever happens to be beneath the development IDE your using. Something else you can do is use the NetBeans sources as your platform, once you've checked them out. That's something I did the other day when trying to see whether adding 'setActivatedNodes' to NbSheet was sufficient for getting UndoRedo enabled in the Properties Window. So that's a good use case, i.e., you'd like to change the NetBeans Platform somehow, or you're fixing a bug, in other words, in some way you need to change the NetBeans Platform sources and then would like to try out the result of your changes as a client of your changes. In that scenario, here's how to set up and use a NetBeans Platform from the NetBeans sources. Run 'ant build platform' on the root of the NetBeans sources. You'll end up with nbbuild/netbeans containing a subfolder 'platform' and a subfolder 'harness'. There's your NetBeans Platform. Go to Tools | NetBeans Platform and browse to nbbuild/netbeans', registering it as your NetBeans Platform. Create a new NetBeans module, using the new NetBeans Platform as the platform. Now the cool thing is you can open any of the NetBeans modules from the NetBeans Platform modules in the NetBeans sources. When you change the source code of one of these modules and then build that module, the changed JAR will automatically be added to the right place in the nbbuild/netbeans folder. And when you do a 'clean' on a NetBeans Platform module, the related JAR will be removed from nbbuild/netbeans. In other words, in this way, by changing the NetBeans sources, you're directly changing the platform that your custom module will be running on when you deploy it. That's pretty cool and gives you a more connected relationship to your platform, since you're able to change it in the same way as the custom modules you create.

  Read the article

• Audio not working

  - by user3215

  Anybody could help me in troubleshooting audio problem on ubutnu 9.04 desktop edition?. For some reason I've to keep this os not upgraded and I'm trying to fix the audio problem on this for months. It works well on upgraded version(9.10,10.04) but not on jaunty. aplay -l: **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: ALC883 Analog [ALC883 Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC883 Digital [ALC883 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 lsmod | grep snd: snd_hda_intel 436148 7 snd_pcm_oss 46336 0 snd_mixer_oss 22656 1 snd_pcm_oss snd_pcm 83076 4 snd_hda_intel,snd_pcm_oss snd_seq_dummy 10756 0 snd_seq_oss 37760 0 snd_seq_midi 14336 0 snd_rawmidi 29696 1 snd_seq_midi snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi snd_seq 56880 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event snd_timer 29704 2 snd_pcm,snd_seq snd_seq_device 14988 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq snd 62756 21 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15200 1 snd snd_page_alloc 16904 2 snd_hda_intel,snd_pcm cat /proc/asound/cards: 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xe1280000 irq 16 cat /proc/asound/version: Advanced Linux Sound Architecture Driver Version 1.0.18rc3. vim /etc/modules: # /etc/modules: kernel modules to load at boot time. # # This file contains the names of kernel modules that should be loaded # at boot time, one per line. Lines beginning with "#" are ignored. lp Audio Settings:

  Read the article

• What are the packages/libraries I should install before compiling Python from source?

  - by Lennart Regebro

  Once in a while I need to install a new Ubuntu (I used it both for desktop and servers) and I always forget a couple of libraries I should have installed before compiling, meaning I have to recompile, and it's getting annoying. So now I want to make a complete list of all library packages to install before compiling Python (and preferably how optional they are). This is the list I compiled with below help and by digging in setup.py. It is complete for Ubuntu 10.04 and 11.04 at least: build-essential (obviously) libz-dev (also pretty common and essential) libreadline-dev (or the Python prompt is crap) libncursesw5-dev libssl-dev libgdbm-dev libsqlite3-dev libbz2-dev More optional: tk-dev libdb-dev Ubuntu has no packages for v1.8.5 of the Berkeley database, nor (for obvious reasons) the Sun audio hardware, so the bsddb185 and sunaudiodev modules will still not be built on Ubuntu, but all other modules are built with the above packages installed. Python 2.5 and Python 2.6 also needs to have LDFLAGS set on Ubuntu 11.04 and later, to handle the new multi-arch layout: export LDFLAGS="-L/usr/lib/$(dpkg-architecture -qDEB_HOST_MULTIARCH)" For Python 2.6 and 2.7 you also need to explicitly enable SSL after running the ./configure script and before running make. In Modules/Setup there are lines like this: #SSL=/usr/local/ssl #_ssl _ssl.c \ # -DUSE_SSL -I$(SSL)/include -I$(SSL)/include/openssl \ # -L$(SSL)/lib -lssl -lcrypto Uncomment these lines and change the SSL variable to /usr: SSL=/usr _ssl _ssl.c \ -DUSE_SSL -I$(SSL)/include -I$(SSL)/include/openssl \ -L$(SSL)/lib -lssl -lcrypto Python 2.6 also needs Modules/_ssl.c modified to be used with OpenSSL 1.0, which is used in Ubuntu 11.10. At around line 300 you'll find this: else if (proto_version == PY_SSL_VERSION_SSL3) self->ctx = SSL_CTX_new(SSLv3_method()); /* Set up context */ else if (proto_version == PY_SSL_VERSION_SSL2) self->ctx = SSL_CTX_new(SSLv2_method()); /* Set up context */ else if (proto_version == PY_SSL_VERSION_SSL23) self->ctx = SSL_CTX_new(SSLv23_method()); /* Set up context */ Change that into: else if (proto_version == PY_SSL_VERSION_SSL3) self->ctx = SSL_CTX_new(SSLv3_method()); /* Set up context */ #ifndef OPENSSL_NO_SSL2 else if (proto_version == PY_SSL_VERSION_SSL2) self->ctx = SSL_CTX_new(SSLv2_method()); /* Set up context */ #endif else if (proto_version == PY_SSL_VERSION_SSL23) self->ctx = SSL_CTX_new(SSLv23_method()); /* Set up context */ This disables SSL_v2 support, which apparently is gone in OpenSSL1.0.

  Read the article

• Having trouble installing guest additions for a Xubuntu 13.10 guest OS in Virtualbox 4.2.10

  - by Duval Pearson III

  I am using Ubuntu 13.04 64-BIT as my host operating system running Virtual Box 4.2.10. I get this message when I tell virtualbox to install guest additions(CTRL+D),mounting the volume in the guest OS and run the VBoxLinuxAdditions.run file using root by: sudo ./VBoxLinuxAdditions.run It starts and then comes to these error messages: Verifying archive integrity... All good. Uncompressing VirtualBox 4.2.10 Guest Additions for Linux.......... VirtualBox Guest Additions installer Removing existing VirtualBox non-DKMS kernel modules ...done. Building the VirtualBox Guest Additions kernel modules The headers for the current running kernel were not found. If the following module compilation fails then this could be the reason. Building the main Guest Additions module ...done. Building the shared folder support module ...fail! (Look at /var/log/vboxadd-install.log to find out what went wrong) Doing non-kernel setup of the Guest Additions ...done. Installing the Window System drivers Warning: unknown version of the X Window System installed. Not installing X Window System drivers. Installing modules ...done. Installing graphics libraries and desktop services components ...done. allusers@allusers-VirtualBox:/media/allusers/VBOXADDITIONS_4.2.10_84104$ I followed everything from the official VirtualBox manual on installing guest additions for linux I used some other commands such as: sudo apt-get install build-essential linux-headers-$(uname -r) dkms and: sudo apt-get install virtualbox-guest-x11 I rebooted after executing those command and it still wont work. It still says the kernel modules are missing and the window is not seamless. Any idea what could be the problem?

  Read the article

• Resetup kernel for virtualbox and now ubuntu is in initramfs state

  - by UbuntuMan

  My 10.04LTS became Read-Only so I wanted to reboot this virtual machine. Then I couldn't get it back up running. VirtualBox threw Result Code: NS_ERROR_FAILURE (0x80004005) error. I did the kernel re-setup: sudo /etc/init.d/vboxdrv setup * Stopping VirtualBox kernel modules [ OK ] * Uninstalling old VirtualBox DKMS kernel modules [ OK ] * Trying to register the VirtualBox kernel modules using DKMS [ OK ] * Starting VirtualBox kernel modules [ OK ] I can't even use sudo in this state. What can I do? (initframfs) /dev/sda1 /bin/sh: /dev/sda1: Permission denied (initframfs) /dev/sda2 /bin/sh: /dev/sda3: Permission denied (initframfs) /dev/sda3 /bin/sh: /dev/sda1: not found I have a similar image so I can check the disks setting if needed. Please help me. Thanks. I have an older version of VirtualBox: 4.0.8 something like that. But other vms on the same VirtualBox are working fine. UPDATE I can hold down SHIFT key and see the GURU menu. Only one kernel exists. Ubuntu(...) Ubuntu(recovery) master test master test

  Read the article

• iptables unresolved dependencies

  - by tertle

  I'm trying to setup OpenVPN Access Server on a VPS running ubuntu 9.10 for a friend so she can play games from her uni campus. The problem is I keep running into this error when trying to start openvpn. Service deferred error: IPTablesServiceBase: failed to run iptables-restore [status=1]: ['FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'iptables-restore: line 46 failed']: internet/base:1175,internet/base:752,internet/process:45,internet/process:306,internet/_baseprocess:48,internet/process:775,internet/_baseprocess:60,svc/pp:116,svc/svcnotify:26,internet/defer:238,internet/defer:307,internet/defer:323,sagent/ipts:105,sagent/ipts:39,util/error:52,util/error:32 service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['iptables_openvpn']) Now I've already got my provider to enabled the TUN/TAP device driver and I checked this using # cat /dev/net/tun Which returned “File descriptor in bad state” Which I believe means it's enabled. After extensive searching, I've been unable to find any solution other than people suggesting to make sure TUN/TAP device driver is enabled. Any ideas on how to solve my issue? I'm not very experience with linux and I feel in over my head here so any advice is greatly appreciated. --edit-- Just stumbled across this Not sure how I missed it earlier. I believe I need to get modprobe ipt_mark & modprobe ipt_MARK run on the hostnode by my provider. Is this correct and something I should try get done.

  Read the article

• Netbook Remix 10.04 to 10.10 upgrade using alternate iso

  - by Suman Subramonian

  I'm using Netbook Remix 10.04 now. I'm having the 10.10 alternate iso with me. If I use that iso to upgrade, will I lose my netbook version? I've seen in some forums that the upgrade resulted in a change from netbook version to desktop version. Updated on 15/12/2010 I upgraded the OS from 10.04 to 10.10. But I'm getting an error like this after restart: modprobe: FATAL: Could not load /lib/modules/2.6.35-22-generic/modules.dep: No such file or directory I searched in the forums and got a solution like this: Open Terminal gksudo gedit /etc/initramfs-tools/initramfs.conf change the line MODULES=most to MODULES=dep Then use Synaptic (SystemAdministrationSynaptic Package Manager) to reinstall initramfs-tools. I'll be definitely trying this later. After that when the system tries to login, my screen starts flashing with just the ubuntu netbook desktop wallpaper on the screen. No other options will be available. It will be flashing continuosly. If I press the power button then one window comes up with options like Shut down, Restart, Hibernate etc. And the screen won't stop flashing either. I've uploaded a 1 min video. Please go through it as it will give you a clear idea of the error which I'm facing now Video Link Here

  Read the article

• When module calling gets ugly

  - by Pete

  Has this ever happened to you? You've got a suite of well designed, single-responsibility modules, covered by unit tests. In any higher-level function you code, you are (95% of the code) simply taking output from one module and passing it as input to the next. Then, you notice this higher-level function has turned into a 100+ line script with multiple responsibilities. Here is the problem. It is difficult (impossible) to test that script. At least, it seems so. Do you agree? In my current project, all of the bugs came from this script. Further detail: each script represents a unique solution, or algorithm, formed by using different modules in different ways. Question: how can you remedy this situation? Knee-jerk answer: break the script up into single-responsibility modules. Comment on knee-jerk answer: it already is! Best answer I can come up with so far: create higher-level connector objects which "wire" modules together in particular ways (take output from one module, feed it as input to another module). Thus if our script was: FooInput fooIn = new FooInput(1, 2); FooOutput fooOutput = fooModule(fooIn); Double runtimevalue = getsomething(fooOutput.whatever); BarInput barIn = new BarInput( runtimevalue, fooOutput.someOtherValue); BarOutput barOut = barModule(BarIn); It would become with a connector: FooBarConnectionAlgo fooBarConnector = new fooBarConnector(fooModule, barModule); FooInput fooIn = new FooInput(1, 2); BarOutput barOut = fooBarConnector(fooIn); So the advantage is, besides hiding some code and making things clearer, we can test FooBarConnectionAlgo. I'm sure this situation comes up a lot. What do you do?

  Read the article

• Updating to linux-image-3.2.0-26-generic occupies all disk space

  - by user42228

  I just ran a normal update through the update manager that wanted to update me to linux-image-3.2.0-26-generic. The installation paused halfway with a message that the root was full. I checked the disk usage, and noticed that one of the newly installed files: /lib/modules/3.2.0-26-generic/modules.ccwmap took up 63GB(!). Compared to the previous version: /lib/modules/3.2.0-24-generic/modules.ccwmap that took up only 4KB it seems like something went awfully wrong! As mentioned the update was paused when i ran out of disk space. There is no option in the update dialog to cancel or perform rollback on the update. Is it asking for trouble to kill the update manager? Any ideas as to what went wrong, and what I can do to remedy it? It's only minimal how much space I can free on that partition (without deleting the above mentioned file). If it is any help, the update was paused after this: Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic

  Read the article

• Hibernate exception

  - by Mark

  Hi all, im new to hibernate! i have followed the netbeans tutorial on creating a hibernate enabled application. after sucessfully creating a database in mysql workbench i reversed engineered the pojos etc and then tried to run a simple query(from Course) and got the following org.hibernate.MappingException: An association from the table coursemodule refers to an unmapped class: DAL.Module at org.hibernate.cfg.Configuration.secondPassCompileForeignKeys(Configuration.java:1252) at org.hibernate.cfg.Configuration.secondPassCompile(Configuration.java:1170) at org.hibernate.cfg.AnnotationConfiguration.secondPassCompile(AnnotationConfiguration.java:324) at org.hibernate.cfg.Configuration.buildSessionFactory(Configuration.java:1286) at org.hibernate.cfg.AnnotationConfiguration.buildSessionFactory(AnnotationConfiguration.java:859) heres the generated class for Course package DAL; // Generated 02-May-2010 16:41:16 by Hibernate Tools 3.2.1.GA import java.util.HashSet; import java.util.Set; /** * Course generated by hbm2java */ public class Course implements java.io.Serializable { private int id; private String name; private Set<Module> modules = new HashSet<Module>(0); public Course() { } public Course(int id, String name) { this.id = id; this.name = name; } public Course(int id, String name, Set<Module> modules) { this.id = id; this.name = name; this.modules = modules; } public int getId() { return this.id; } public void setId(int id) { this.id = id; } public String getName() { return this.name; } public void setName(String name) { this.name = name; } public Set<Module> getModules() { return this.modules; } public void setModules(Set<Module> modules) { this.modules = modules; } } and its config file course.hbm.xml <?xml version="1.0"?> <!DOCTYPE hibernate-mapping PUBLIC "-//Hibernate/Hibernate Mapping DTD 3.0//EN" "http://hibernate.sourceforge.net/hibernate-mapping-3.0.dtd"> <!-- Generated 02-May-2010 16:41:16 by Hibernate Tools 3.2.1.GA --> <hibernate-mapping> <class name="DAL.Course" table="course" catalog="walkthrough"> <id name="id" type="int"> <column name="id" /> <generator class="assigned" /> </id> <property name="name" type="string"> <column name="name" not-null="true" /> </property> <set name="modules" inverse="false" table="coursemodule"> <key> <column name="courseId" not-null="true" unique="true" /> </key> <many-to-many entity-name="DAL.Module"> <column name="moduleId" not-null="true" unique="true" /> </many-to-many> </set> </class> </hibernate-mapping> hibernate.reveng.xml <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE hibernate-reverse-engineering PUBLIC "-//Hibernate/Hibernate Reverse Engineering DTD 3.0//EN" "http://hibernate.sourceforge.net/hibernate-reverse-engineering-3.0.dtd"> <hibernate-reverse-engineering> <schema-selection match-catalog="Walkthrough"/> <table-filter match-name="walkthrough"/> <table-filter match-name="course"/> <table-filter match-name="module"/> <table-filter match-name="studentmodule"/> <table-filter match-name="attendee"/> <table-filter match-name="student"/> <table-filter match-name="coursemodule"/> <table-filter match-name="session"/> <table-filter match-name="test"/> </hibernate-reverse-engineering> hibernate.cfg.xml <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE hibernate-configuration PUBLIC "-//Hibernate/Hibernate Configuration DTD 3.0//EN" "http://hibernate.sourceforge.net/hibernate-configuration-3.0.dtd"> <hibernate-configuration> <session-factory> <property name="hibernate.dialect">org.hibernate.dialect.MySQLDialect</property> <property name="hibernate.connection.driver_class">com.mysql.jdbc.Driver</property> <property name="hibernate.connection.url">jdbc:mysql://localhost:3306/Walkthrough</property> <property name="hibernate.connection.username">root</property> <property name="hibernate.connection.password">password</property> <property name="hibernate.show_sql">true</property> <property name="hibernate.current_session_context_class">thread</property> <mapping resource="DAL/Student.hbm.xml"/> <mapping resource="DAL/Walkthrough.hbm.xml"/> <mapping resource="DAL/Test.hbm.xml"/> <mapping resource="DAL/Module.hbm.xml"/> <mapping resource="DAL/Session.hbm.xml"/> <mapping resource="DAL/Course.hbm.xml"/> </session-factory> </hibernate-configuration> any ideas on why im getting this exception? ps. test is just a table with an id in it and is not related to anything. running "from Test" works

  Read the article

• CodePlex Daily Summary for Monday, June 14, 2010

  CodePlex Daily Summary for Monday, June 14, 2010New ProjectsBD File Hash: BD File Hash is a convenient file hash and hash compare tool for Windows which currently works with MD5, SHA-1, and SHA-256 algorithms. FileScan: This is an application that searches through a drive or directory structure for files matching a filter. This project was converted from VB to ...genesis9: genesis9HeinanOS: HeinanOS is an operating system developed mainly in C++. HeinanOS is a light OS (1.44 MB image) with a lot of capabilites and many more are being ...MediaBrowserWS - Creates a Web Service for the popular MediaBrowser plugin: Creates a web service in Media Center for accessing your MediaBrowser collection. Allows for external devices (Tablets/phones/laptops) to access a ...MME: New Edition of Managed Menu Extensions for Visual Studio 2010 The Main goal of "MME" is to provide easy access to adding Right Click menus in the ...MVMMapper: Generate the ViewModel and its mapping to the Model when implementing MVVM in .NET. Developed using T4 templates. Current version supports Silver...ProjectArDotNet: Si te agarro te parto! Si te agarro te emperno no me importa que seas menor de edad!Scriptagility for DotNetNuke: Scriptagility is a DotNetNuke module for Javascript developers. This module provides dynamic client scripting infrastructure for developing javascr...simpleLinux Distro: SimpleLinux. is a Linux distributions that is easy to use. Simple Linux website: http://simplelinux.tkTag Cloud Control for asp.net: Tag Cloud Control for asp.net allows the user to display the most important keywords to display in tag cloud. Each Tag has it own navigation url to...thefreeimdb: fsadie qwUppityUp: UppityUp is a simple and light-weight tray application which monitors a remote server and shows a notification when it comes online. This is usefu...Vivid3D 2 - DirectX 10 3D ToolKit: The sequel to my first ever engine wrote several years ago. It is not based on it in anyway. VSIDev: VSI DevXTQXK_WORK: Actionscript 3.0东坡博客: 这是一个ASP。net mvc 2博客。New Releases.NET Extensions - Extension Methods Library: Release 2010.08: Added extension methods for Bitmap manipulation (scaling for now): - Bitmap.ScaleToSize() - Bitmap.ScaleToSizeProportional() - Bitmap.ScaleProport...Black Falcon Software's Database Data-Access-Layers: “SQLHELPER”, “ORAHELPER” - Handling Binary Data: See attached document...BTech Networking Library: BTech Networking Library: Same as pervious just new namespace, extended networking coming soon!!!Community Forums NNTP bridge: Community Forums NNTP Bridge V37: Release of the Community Forums NNTP Bridge to access the social and anwsers MS forums with a single, open source NNTP bridge. This release has ad...Generic Entity Model 2: GEM2 build 54383: This is second BETA release of GEM2! Please see source code change sets for updates! Following implementation is not included in this release: My...Hades: Projet Hadès - Official Demo - Version 0.1.0 Beta: ---------------------------------------------------------------------------- - Projet Hadès - Official Demo - Version 0.1.0 Beta ------------------...HeinanOS: HeinanOS M1 Source Code: You can download HeinanOS M1 Source Code and contribute to HeinanOS development! Be aware that you should not use this code for your own systems! ...HeinanOS: Milestone 1: This is the first major release for HeinanOS 1.0 Please note this is a PRE-RELEASE! This release includes the following features: -Bootable DOS-...HKGolden Express: HKGoldenExpress (Build 201006131900): New features: (None) Bug fix: Incorrect message submit date of message/ replies. (Note: Showing message submit date is enabled since Build 20100...HKGolden Express: HKGoldenExpress (Build 201006140110): New features: (None) Bug fix: (None) Improvements: (None) Other changes: Set time zone of message date as Hong Kong. Adjusted the format of messa...MediaCoder.NET: MediaCoder.NET v1.0 Beta 1.5: Installer file for MediaCoder.NET v1.0 beta 1.5. Now converts multiple files.MME: First release: Features of this release 1. One installer MME.msi. However you can also install MMEMenuManagerSetup.vsix which installs a project template that e...MSBuild Launch Pad (mPad): 1.1 Beta 1: Platform selection box is added.MVMMapper: MVMMapper Release v 1.0.1: This release has no downloadable documentation. Please use the Documentation section to get started.NginxTray: NginxTray 0.7 RC2: NginxTray 0.7 RC2PowerAuras: PowerAuras-3.0.0K-beta3: New Auras: Item Name Equipment Slot Tracking Changes from beta1 5 new aura textures Fixed Tracking bug Added graphical equipment slot sele...PowerAuras: PowerAuras-3.0.0K-beta4: New Auras: Item Name Equipment Slot Tracking Changes from beta1 5 new aura textures Fixed Tracking bug Added graphical equipment slot sele...Scriptagility for DotNetNuke: Scriptagility 1.0 (Beta): Initial public release please evaluate and feedbackSharpDevelop: SharpDevelop 4.0 Beta 1: Release notes: http://community.sharpdevelop.net/forums/t/11388.aspxsimpleLinux Distro: Project X3: This is an example of download for simpleLinuxSOAPI - StackOverflow API Parser/Wrapper Generator: SOAPI Beta 3: The SOAPI Beta 3 download will be made availabe later today when the initial documentation is complete. The previously available Beta 1 download h...Sofa: Initial release V1.0: This is the first release of Sofa. As it is made of code being previously used, as we tested it is a stable release. But bugs are always possible,...Tag Cloud Control for asp.net: Tag Cloud Control for asp.net: Tag Cloud Control for asp.net allows the user to display the most important keywords to display in tag cloud. Each Tag has it own navigation url to...UppityUp: UppityUp v0.1: First functional version, supports monitoring availability by ping (ICMP) requests. Fit for general use. Consists of one standalone .exe file - no...VCC: Latest build, v2.1.30613.0: Automatic drop of latest buildWindStyle ExifInfo for Windows Live Writer: 1.1.0.0: Add: Multiple Language(English and Simplified Chinese); Add: Insert multiple files; Fix: Error when insert pictures without Exif info; Update: Icon...Work Recorder - Hold on own time!: WorkRecorder 1.2: +Add a whole day chartXsltDb - DotNetNuke Module Builder: 01.01.24: Syntax highlighting delivered!New samples for RadControls. On single page you can find RadTreeView, RadRating, RadChart, RadFormDecorator, RadEdito...xUnit.net Contrib: xunitcontrib 0.4 (ReSharper 5.0 RTM + dotCover): xunitcontrib release 0.4 (ReSharper runner) This release provides a test runner plugin for Resharper 5.0, 4.5 and 4.1, targetting all versions of x...Most Popular ProjectsCommunity Forums NNTP bridgeRIA Services EssentialsNeatUploadBxf (Basic XAML Framework)Agile Personal Development Methodology.NET Transactional File ManagerSOLID by exampleASP.NET MVC Time PlannerWEI ShareSiverlight ProjectMost Active ProjectsjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryNB_Store - Free DotNetNuke Ecommerce Catalog ModuleRhyduino - Arduino and Managed CodeCommunity Forums NNTP bridgeCassandraemonBlogEngine.NETLightweight Fluent WorkflowMediaCoder.NETAndrew's XNA Helpers

  Read the article

• CodePlex Daily Summary for Wednesday, September 05, 2012

  CodePlex Daily Summary for Wednesday, September 05, 2012Popular ReleasesDesktop Google Reader: 1.4.6: Sorting feeds alphabetical is now optional (see preferences window)DotNetNuke® Community Edition CMS: 06.02.03: Major Highlights Fixed issue where mailto: links were not working when sending bulk email Fixed issue where uses did not see friendship relationships Problem is in 6.2, which does not show in the Versions Affected list above. Fixed the issue with cascade deletes in comments in CoreMessaging_Notification Fixed UI issue when using a date fields as a required profile property during user registration Fixed error when running the product in debug mode Fixed visibility issue when...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.65: Fixed null-reference error in the build task constructor.BLACK ORANGE: HPAD TEXT EDITOR 0.9 Beta: HOW TO RUN THE TEXT EDITOR Download the HPAD ARCHIVED FILES which is in .rar format Extract using Winrar Make sure that extracted files are in the same folder Double-Click on HPAD.exe application fileTelerikMvcGridCustomBindingHelper: Version 1.0.15.247-RC2: TelerikMvcGridCustomBindingHelper 1.0.15.247 RC2 Release notes: This is a RC version (hopefully the last one), please test and report any error or problem you encounter. This release is all about performance and fixes Support: "Or" and "Does Not contain" filter options Improved BooleanSubstitutes, Custom Aggregates and expressions-to-queryover Add EntityFramework examples in ExampleWebApplication Many other improvements and fixes Fix invalid cast on CustomAggregates Support for ...ServiceMon - Extensible Real-time, Service Monitoring Utility: ServiceMon Release 0.9.0.44: Auto-uploaded from build serverJavaScript Grid: Release 09-05-2012: Release 09-05-2012xUnit.net Contrib: xunitcontrib-dotCover 0.6.1 (dotCover 2.1 beta): xunitcontrib release 0.6.1 for dotCover 2.1 beta This release provides a test runner plugin for dotCover 2.1 beta, targetting all versions of xUnit.net. (See the xUnit.net project to download xUnit.net itself.) This release adds support for running xUnit.net tests to dotCover 2.1 beta's Visual Studio plugin. PLEASE NOTE: You do NOT need this if you also have ReSharper and the existing 0.6.1 release installed. DotCover will use ReSharper's test runners if available. This release includes th...B INI Sharp Library: B INI Sharp Library v1.0.0.0 Realsed: The frist realsedActive Forums for DotNetNuke CMS: Active Forums 5.0.0 RC: RC release of Active Forums 5.0.Droid Explorer: Droid Explorer 0.8.8.7 Beta: Bug in the display icon for apk's, will fix with next release Added fallback icon if unable to get the image/icon from the Cloud Service Removed some stale plugins that were either out dated or incomplete. Added handler for *.ab files for restoring backups Added plugin to create device backups Backups stored in %USERPROFILE%\Android Backups\%DEVICE_ID%\ Added custom folder icon for the android backups directory better error handling for installing an apk bug fixes for the Runn...BI System Monitor: v2.1: Data Audits report and supporting SQL, and SSIS package Environment Overview report enhancements, improving the appearance, addition of data audit finding indicators Note: SQL 2012 version coming soon.The Visual Guide for Building Team Foundation Server 2012 Environments: Version 1: --Nearforums - ASP.NET MVC forum engine: Nearforums v8.5: Version 8.5 of Nearforums, the ASP.NET MVC Forum Engine. New features include: Built-in search engine using Lucene.NET Flood control improvements Notifications improvements: sync option and mail body View Roadmap for more details webdeploy package sha1 checksum: 961aff884a9187b6e8a86d68913cdd31f8deaf83WiX Toolset: WiX Toolset v3.6: WiX Toolset v3.6 introduces the Burn bootstrapper/chaining engine and support for Visual Studio 2012 and .NET Framework 4.5. Other minor functionality includes: WixDependencyExtension supports dependency checking among MSI packages. WixFirewallExtension supports more features of Windows Firewall. WixTagExtension supports Software Id Tagging. WixUtilExtension now supports recursive directory deletion. Melt simplifies pure-WiX patching by extracting .msi package content and updating .w...Iveely Search Engine: Iveely Search Engine （0.2.0）: ????ISE?0.1.0??，?????，ISE?0.2.0?????????，???????，????????20???follow?ISE，????，??ISE??????????，??????????，?????????，?????????0.2.0??????，??????????。 Iveely Search Engine ?0.2.0?????????“??????????”，??????，?????????，???????，???????????????????，????、????????????。???0.1.0????????????： 1. ??“????” ??。??????????，?????????，???????????????????。??：????????，????????????，??????????????????。??????。 2. ??“????”??。?0.1.0??????，???????，???????????????，?????????????，????????，?0.2.0?，???????...GmailDefaultMaker: GmailDefaultMaker 3.0.0.2: Add QQ Mail BugfixSmart Data Access layer: Smart Data access Layer Ver 3: In this version support executing inline query is added. Check Documentation section for detail.DotNetNuke® Form and List: 06.00.04: DotNetNuke Form and List 06.00.04 Don't forget to backup your installation before upgrade. Changes in 06.00.04 Fix: Sql Scripts for 6.003 missed object qualifiers within stored procedures Fix: added missing resource "cmdCancel.Text" in form.ascx.resx Changes in 06.00.03 Fix: MakeThumbnail was broken if the application pool was configured to .Net 4 Change: Data is now stored in nvarchar(max) instead of ntext Changes in 06.00.02 The scripts are now compatible with SQL Azure, tested in a ne...Coevery - Free CRM: Coevery 1.0.0.24: Add a sample database, and installation instructions.New ProjectsA Simple Eng-Hindi CMS: A simple English- Hindi dual language content management system for small business/personal websites.Active Social Migrator: This project for managing the Active Social migration tool.ANSI Console User Control: Custom console control for .NET WinformsAutoSPInstallerGUI: GUI Configuration Tool for SPAutoInstaller Codeplex ProjectCode Documentation Checkin Policy: This checkin policy for Visual Studio 2012 checks if c# code is documented the way it's configured in the config of the policy. Code Dojo/Kata - Free Time Coding: Doing some katas of the Coding Dojo page. http://codingdojo.org/cgi-bin/wiki.pl?KataCataloguefjycUnifyShow: fjycUnifyShowHidden Capture (HC): HC is simple and easy utility to hidden and auto capture desktop or active windowHRC Integration Services: Fake SQL Server Integration Services. LOLKooboo CMS Sites Switcher: Kooboo CMS Sites SwitcherMod.CookieDetector: Orchard module for detecting whether cookies are enabledMyCodes: Created!MySQL Statement Monitor: MySQL Statement Monitor is a monitoring tool that monitors SQL statements transferred over the network.NeoModulusPIRandom: The idea with PI Random is to use easy string manipulation and simple math to generate a pseudo random number. Net Core Tech - Medical Record System: This is a Medical Record System ProjectOraPowerShell: PowerShell library for backup and maintenance of a Oracle Database environment under Microsoft Windows 2008PinDNN: PinDNN is a module that imparts Pinterest-like functionality to DotNetNuke sites. This module works with a MongoDB database and uses the built-in social relatioPyrogen Code Generator: PyroGen is a simple code generator accepting C# as the markup language.restMs: wil be deleted soonScript.NET: Script.NET is a script management utility for web forms and MVC, using ScriptJS-like features to link dependencies between scripts.SpringExample-Pagination: Simple Spring example with PaginationXNA and Component Based Design: This project includes code for XNA and Component Based Design

  Read the article

• CodePlex Daily Summary for Monday, March 05, 2012

  CodePlex Daily Summary for Monday, March 05, 2012Popular ReleasesSimple Injector: Simple Injector v1.4.1: This release adds two small improvements to the SimpleInjector.Extensions.dll. No changes have been made to the core library. New features and improvements in this release for the SimpleInjector.Extensions.dll The RegisterManyForOpenGeneric extension methods now accept non-generic decorator, as long as they implement the given open generic service type. GetTypesToRegister methods added to the OpenGenericBatchRegistrationExtensions class which allows to customize the behavior. Note that the...SQL Scriptz Runner: Application: Scriptz Runner source code and applicationCommonLibrary: Code: CodePowerGUI Visual Studio Extension: PowerGUI VSX 1.5.2: Added support for PowerGUI 3.2.Path Copy Copy: 10.0: New version with the following biggest new features: Regular expression support in custom commands (see this work item) Import/export feature for custom commands (see this work item) This version also addresses the following work items: 11353 11348 This version is a recommended upgrade for all users. Note: new custom commands that user regular expressions won't be compatible with earlier versions (if installed by registry manipulation or via network installation), but everything else is ...VidCoder: 1.3.1: Updated HandBrake core to 0.9.6 release (svn 4472). Removed erroneous "None" container choice. Change some logic and help text to stop assuming you have to pick the VIDEO_TS folder for a DVD scan. This should make previewing DVD titles on the Queue Multiple Titles window possible when you've picked the root DVD directory.ASP.NET MVC Framework - Abstracting Data Annotations, HTML5, Knockout JS techs: Version 1.0: Please download the source code. I am not associating any dll for release.ExtAspNet: ExtAspNet v3.1.0: ExtAspNet - ?? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ?????????? ExtAspNet ????? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ??????????。 ExtAspNet ??????? JavaScript，?? CSS，?? UpdatePanel，?? ViewState，?? WebServices ???????。 ??????: IE 7.0, Firefox 3.6, Chrome 3.0, Opera 10.5, Safari 3.0+ ????：Apache License 2.0 (Apache) ??：http://extasp.net/ ??：http://bbs.extasp.net/ ??：http://extaspnet.codeplex.com/ ??：http://sanshi.cnblogs.com/ ????： +2012-03-04 v3.1.0 -??Hidden???????（〓?〓）。 -?PageManager??...AcDown????? - Anime&Comic Downloader: AcDown????? v3.9.1: ?? ●AcDown??????????、??、??????，????1M，????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。??????AcPlay?????，??????、????????????????。 ● AcDown???????????????????????????，???，???????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ????????????? ??：????????Windows XP???,?????????.NET Framework 2.0???(x86)，?????"?????????"??? ??????????????，??????????： ??"AcDo...Windows Phone Commands for VS2010: Version 1.0: Initial Release Version 1.0 Connect from device or emulator (Monitors the connection) Show Device information (Plataform, build , version, avaliable memory, total memory, architeture Manager installed applications (Launch, uninstall and explorer isolate storage files) Manager core applications (Launch blocked applications from emulator (Office, Calculator, alarm, calendar , etc) Manager blocked settings from emulator (Airplane Mode, Celullar Network, Wifi, etc) Deploy and update ap...DNN Metro7 style Skin package: Metro7 style Skin for DotNetNuke 06.01.00: Changes on Version 06.01.00 Fixed issue on GraySmallTitle container, that breaks the layout Fixed issue on Blue Metro7 Skin where the Search, Login, Register, Date is missing Fixed issue with the Version numbers on the target file Fixed issue where the jQuery and jQuery-UI files not deleted on upgrade from Version 01.00.00 Added a internal page where the Image Slider would be replaces with a BannerPaneMedia Companion: MC 3.433b Release: General More GUI tweaks (mostly imperceptible!) Updates for mc_com.exe TV The 'Watched' button has been re-instigated Added TV Menu sub-option to search ALL for new Episodes (includes locked shows) Movies Added 'Source' field (eg DVD, Bluray, HDTV), customisable in Advanced Preferences (try it out, let us know how it works!) Added HTML <<format>> tag with optional parameters for video container, source, and resolution (updated HTML tags to be added to Documentation shortly) Known Issu...Picturethrill: Version 2.3.2.0: Release includes Self-Update feature for Picturethrill. What that means for users is that they are always guaranteed to have a fresh copy of Picturethrill on their computers with all latest fixes. When Picturethrill adds a new website to get pictures from, you will get it too!Simple MVVM Toolkit for Silverlight, WPF and Windows Phone: Simple MVVM Toolkit v3.0.0.0: Added support for Silverlight 5.0 and Windows Phone 7.1. Upgraded project templates and samples. Upgraded installer. There are some new prerequisites required for this version, namely Silverlight 5 Tools, Expression Blend Preview for Silverlight 5 (until the SDK is released), Windows Phone 7.1 SDK. Because it is in the experimental band, I have also removed the dependency on the Silverlight Testing Framework. You can use it if you wish, but the Ria Services project template no longer uses ...CODE Framework: 4.0.20301: The latest version adds a number of new features to the WPF system (such as stylable and testable messagebox support) as well as various new features throughout the system (especially in the Utilities namespace).MyRouter (Virtual WiFi Router): MyRouter 1.0.2 (Beta): A friendlier User Interface. A logger file to catch exceptions so you may send it to use to improve and fix any bugs that may occur. A feedback form because we always love hearing what you guy's think of MyRouter. Check for update menu item for you to stay up to date will the latest changes. Facebook fan page so you may spread the word and share MyRouter with friends and family And Many other exciting features were sure your going to love!WPF Sound Visualization Library: WPF SVL 0.3 (Source, Binaries, Examples, Help): Version 0.3 of WPFSVL. This includes three new controls: an equalizer, a digital clock, and a time editor.Orchard Project: Orchard 1.4: Please read our release notes for Orchard 1.4: http://docs.orchardproject.net/Documentation/Orchard-1-4-Release-NotesNetSqlAzMan - .NET SQL Authorization Manager: 3.6.0.15: 3.6.0.15 28-Feb-2012 • Fix: The communication object, System.ServiceModel.Channels.ServiceChannel, cannot be used for communication because it is in the Faulted state. Work Item 10435: http://netsqlazman.codeplex.com/workitem/10435 • Fix: Made StorageCache thread safe. Thanks to tangrl. • Fix: Members property of SqlAzManApplicationGroup is not functioning. Thanks to tangrl. Work Item 10267: http://netsqlazman.codeplex.com/workitem/10267 • Fix: Indexer are making database calls. Thanks to t...SCCM Client Actions Tool: Client Actions Tool v1.1: SCCM Client Actions Tool v1.1 is the latest version. It comes with following changes since last version: Added stop button to stop the ongoing process. Added action "Query update status". Added option "saveOnlineComputers" in config.ini to enable saving list of online computers from last session. Default value for "LatestClientVersion" set to SP2 R3 (4.00.6487.2157). Wuauserv service manual startup mode is considered healthy on Windows 7. Errors are now suppressed in checkReleases...New ProjectsAbsolute Risk Game: Risk Game is a classic "World Domination Risk" game where you try to conquer the world.Architecture Document Catalog: The Architecture Document Catalog is a catalog for various documentation used by software solution architects. The initial architecture framework supported is from Rozanski and Woods, also called Viewpoints and Perspectives. It's in C#, Silverlight, WCF RIA Services.Background Worker Job Execution & Job Scheduler: Background worker is a multi-threaded job execution and scheduling engine. Very similar to Quartz, but with a slightly different focus.BWOS: preparing a new operating system. and name BWOS. CommonLibrary: Common modules and componentesCustomizeTool: CustomizeToolData Foundry: Data Foundry is a Swiss army knife for database administrator. With capabilities to cross reference check data between tables to find orphaned data and table relations.Data Grid Extensions: Modular extensions for the DataGrid control. Attach filtering capabilities to your existing DataGrid.dk.Helper: dk.Helper makes it easier for tribal wars game players (divoke-kmene.sk) to manage common activities in game. It's developed in C#.ExEn: ExEn is a high-performance implementation of a subset of the XNA API that runs on Silverlight, iOS and Android.Extended Methods for .NET: Developed in VB.NET, this DLL includes some functions I came across over the internet. Originally they were functions. I made some changes to suit my work and recreated them as Extended methods. Currently includes two extended methods for the Image class and one extended method for the String class. I will update it with new methods as I go along.GestionarComenzi: Gestioneaza Comenzi - Firma transporturiGIS Library Management: GIS Library Management System.iFinity Cache Master for DotNetNuke: The iFinity DotNetNuke Cache Master is an Administration module for DotNetNuke. This module allows administrators to inspect the current contents of the ASP.NET Cache in their running DotNetNuke installation. A very useful tool for developers working with the DotNetNuke cache.intelliEssay Document Format Checker: This is a product that tries to check a document's format to see if it conforms to certain given standard.Just T[he]IP: "Just The IP" leverages the Bing API v2 and the ip: Bing Advanced Operator to list the other web sites hosted at this IP Address (that are indexed by Bing).KTool: Ktool is a tool for learning japanese kanji. This program is still in developed. Current version can only display and find a kanji word (Press ctrl-F on main screen for search). Developed in WPF, .NET 4.0Lab Checker: Lab Checker makes it easy for teacher to check students' programs. It allows a student to test his program on a set of test cases which eliminates the need to run the program manually.MeoBox Vera Control Plugin: This is my project for creating a plugin to control my MeoBox ( Scientific Atlanta ) using Vera ( www.micasaverde.com ) Should work with other TV2Client boxesNUnitTestHelper: NUnitTestHelper is a helper class for developing unit tests for C# applications with NUnit framework. This helper library provides set of classes and method which can be used for accomplishing faster unit test development for any kind of project. NUnitTestBase – Supports basic functionality for writing a unit test with NUnit framework. This base class provides built in support for mocking framework. This version provides support for Rhino mocking framework.OnlineExam: Common online examination system based on Asp.net MVC3 can used for knowledge test, I/Q test, college test or most other test project.Orchard Code Generation Extensions: Code Generation Extensions module for Orchard.OrchardTranstion_CN: Orchar?? OsAvatar: to next step showOwnTools: About my toolsPhone Finder App: PhoneFinder will be a Windows Phone platform app alternative for finding a lost or stolen phone. Our plan is to have additional functionality the Windows software does not include. It will be developed using ASP.NET MVC, SQL Server, C#, etc.PoshChat: PoshChat is a client/server chat program written in PowerShell. Supports multiple client connections to a single server to chat.Process Attachment And Secure Text: ProcessAttachmentAndSecureText is an Exchange Transport Agent DLL and associated ASPX page. It is used to 1) strip out attachments and send them to an upload portal, and 2) to strip out text from emails and send it to an upload portal. It is currently coded for Exchange 2010Resource Viewer - Visual Studio Extension: Simply put the “resource viewer extension” enables you to visually view your ResourceDictionary. To open it go to: View – Other Windows – Resource Viewer. When working with WPF/Silverlight you put your reusable resources in a common ResourceDictionary, those resources might be of type Style, SolidColorBrush, DrawingBrush, BitmapImage and more. The problems starts when you have that ResourceDictionary you have no way to see how your resources look like, making the work process (of both t...Scumm XNA: Scumm XNA is an engine that runs old school LucasArts graphical adventure games. It is written completely in C# and will run on PC, Xbox 360 and Windows phone. The code is inspired by ScummVM but this project is not a port, it is a complete rewrite in order to optimize the engine for the CLR. Of course, you will need to own the orinigal games in order to use it. Currently, I will focus my work on the great "Day of Tentacle" game specifically the CD version.SDX DataGrid: SDXDataGrid is a comprehensive data grid component for Microsoft .NET 3.5 web application developers. It is designed to ease the exhausting process of implementing the necessary code for sorting, navigation, grouping, searching and data editing in a data representation object.SQL Scriptz Runner: Features are : Drag And Drop script files Run a directory of script files Sql Script out put messages during execution Script passed or failed that are colored green and red (yellow for running) Stop on error option Open script on error option Run report with time taken for each uComponents Demo: A demo for the code of running uComponents in Umbraco siteUnixTable: UnixTable makes it easier to realize application to access database, with no code but only with visual instrument at runtime. You'll no longer have to write query or code to read table from database. It's developed in Visual Basic for .NET 4. VOA Player.NET: VOA Player is a lightweight windows client for listening VOA Special English. Because of GFW blocking it fetch RSS data via rss2proxy.appspot.com indirectly. User can view article page and listen MP3 stream. The project is a C# implementation of voaplayer.sinaapp.com.Windows Metafile Library: The library supports reading and writing WMF files. Source code is written in pure .NET from scratch following the Windows Metafile Format Specification.Windows Phone 7.1 + MicroFramework (a phone device as remote control): Windows Phone 7.1 + .Net MicroFramework (How use a windows phone device as remote control of a Fez Panda II/MicroFramework board). A windows phone device can be connected to a wifi network (for example a wifi router). If you have also a MicroFramework board connected to the wifi network; you can send some http rest commands from the windows phone device to the MicroFramework board. The microframework board, it must support the tcp/ip protocol through a connect shield. In this exaple it will...XBMC Cache Manager: A Windows Service to manage a shared XBMC MySQL database and shared cache folder.

  Read the article

• Enable wireless on Dell Inspiron 1300

  - by Simon

  As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

  Read the article

• Unable to connect to Wireless after installing Ubuntu 12.10

  - by Moulik

  I am using Asus U56E laptop and after installing Ubuntu 12.10 alongside Windows 8, I am unable to connect to the Wireless. I have been trying to solve this problem since two weeks and couldn't solve it. Please help. Any answer would be appreciated. Here are some command-line results. lspci -v | grep -iA 7 network ubuntu@ubuntu:~$ lspci -v | grep -iA 7 network 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Subsystem: Intel Corporation Centrino Wireless-N + WiMAX 6150 BGN Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at de800000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi lsmod | grep iwlwifi ubuntu@ubuntu:~$ lsmod | grep iwlwifi iwlwifi 386826 0 mac80211 539908 1 iwlwifi cfg80211 206566 2 iwlwifi,mac80211 ubuntu@ubuntu:~$ dmesg | grep iwlwifi [ 57.846261] iwlwifi: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 57.846264] iwlwifi: Copyright(c) 2003-2012 Intel Corporation [ 57.846336] iwlwifi 0000:02:00.0: >pci_resource_len = 0x00002000 [ 57.846338] iwlwifi 0000:02:00.0: >pci_resource_base = ffffc90000c7c000 [ 57.846341] iwlwifi 0000:02:00.0: >HW Revision ID = 0x67 [ 57.846438] iwlwifi 0000:02:00.0: >irq 52 for MSI/MSI-X [ 59.558335] iwlwifi 0000:02:00.0: >loaded firmware version 41.28.5.1 build 33926 [ 59.558514] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUG disabled [ 59.558516] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUGFS enabled [ 59.558517] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 59.558519] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 59.558520] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_P2P disabled [ 59.558522] iwlwifi 0000:02:00.0: >Detected Intel(R) Centrino(R) Wireless-N + WiMAX 6150 BGN, REV=0x84 [ 59.558583] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 59.569083] iwlwifi 0000:02:00.0: >device EEPROM VER=0x557, CALIB=0x6 [ 59.569085] iwlwifi 0000:02:00.0: >Device SKU: 0x150 [ 59.569087] iwlwifi 0000:02:00.0: >Valid Tx ant: 0x1, Valid Rx ant: 0x3 [ 59.569100] iwlwifi 0000:02:00.0: >Tunable channels: 13 802.11bg, 0 802.11a channels [ 70.208469] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.208648] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 [ 70.366319] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.366470] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 sudo lshw -c network ubuntu@ubuntu:~$ sudo lshw -c network *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:84:99:c4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.5.0-17-generic firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 54:04:a6:2b:6a:ef capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) ifconfig ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 54:04:a6:2b:6a:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:176 errors:0 dropped:0 overruns:0 frame:0 TX packets:176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14368 (14.3 KB) TX bytes:14368 (14.3 KB) wlan0 Link encap:Ethernet HWaddr 40:25:c2:84:99:c4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) iwconfig ubuntu@ubuntu:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off iwlist scan ubuntu@ubuntu:~$ iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results nm-tool ubuntu@ubuntu:~$ nm-tool NetworkManager Tool State: disconnected - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 54:04:A6:2B:6A:EF Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: disconnected Default: no HW Address: 40:25:C2:84:99:C4 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points hypeness2: Infra, 00:21:29:DA:08:4F, Freq 2462 MHz, Rate 54 Mb/s, Strength 42 WPA love: Infra, 68:7F:74:17:02:66, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 DIRECT-MwSCX-3400Pamela: Infra, 02:15:99:A3:3F:AC, Freq 2412 MHz, Rate 54 Mb/s, Strength 22 WPA2 router: Infra, 1C:AF:F7:D6:76:F3, Freq 2417 MHz, Rate 54 Mb/s, Strength 20 WPA2 wing: Infra, E8:40:F2:34:E4:F7, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 132LINKSYS: Infra, 00:1A:70:80:1F:E9, Freq 2437 MHz, Rate 54 Mb/s, Strength 57 WEP VMITTAL: Infra, E0:46:9A:3C:F0:C4, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 WEP HP-Print-10-LaserJet 1025: Infra, 7C:E9:D3:7E:F8:10, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 ACNBB: Infra, 00:26:75:22:A6:2F, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 SATKAIVAL: Infra, 00:18:E7:CE:69:A6, Freq 2412 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2 hypeness: Infra, B8:E6:25:24:C3:B1, Freq 2437 MHz, Rate 54 Mb/s, Strength 54 WPA WPA2 CSNetwork: Infra, BC:14:01:58:C5:88, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2 tharma: Infra, BC:14:01:E2:06:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 15 WPA WPA2 Active2.4: Infra, 10:6F:3F:0E:F3:8E, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 ACNBB: Infra, 00:26:75:58:4E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 85 KO: Infra, BC:14:01:2E:AF:A8, Freq 2452 MHz, Rate 54 Mb/s, Strength 22 WPA WPA2 FEAR: Infra, 00:18:4D:C0:BC:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA Pamela: Infra, BC:14:01:52:F6:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 bvrk2: Infra, 78:CD:8E:7B:3C:79, Freq 2457 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 BELL030: Infra, D8:6C:E9:17:AF:09, Freq 2462 MHz, Rate 54 Mb/s, Strength 22 WPA2 Desai: Infra, 00:1D:7E:52:FB:C5, Freq 2437 MHz, Rate 54 Mb/s, Strength 14 WEP Sritharan: Infra, BC:14:01:E5:59:78, Freq 2462 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 PFN: Infra, 00:13:10:8B:CF:45, Freq 2437 MHz, Rate 54 Mb/s, Strength 19 WEP rfkill list all ubuntu@ubuntu:~$ rfkill list all 0: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wimax: WiMAX Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no so these are some more results sudo modprobe -r iwlwifi ubuntu@ubuntu:~$ sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1 ubuntu@ubuntu:~$ sudo modprobe iwlwifi 11n_disable=1 echo "blacklist asus_wmi" | sudo tee -a /etcmodprobe.d/blacklist.conf ubuntu@ubuntu:~$ echo "blacklist asus_wmi" | sudo tee -a /etc/modprobe.d/blacklist.conf blacklist asus_wmi echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf ubuntu@ubuntu:~$ echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi ubuntu@ubuntu:~$ sudo modprobe -rfv iwlwifi rmmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko sudo modprobe -v iwlwifi ubuntu@ubuntu:~$ sudo modprobe -v iwlwifi insmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko 11n_disable=1

  Read the article

• CodePlex Daily Summary for Saturday, November 03, 2012

  CodePlex Daily Summary for Saturday, November 03, 2012Popular ReleasesZXMAK2: Version 2.6.8.2: fix save to SZX snapshot for +3 model fix +3 ULA timingsLaunchbar: Launchbar 4.2.2.0: This release is the first step in cleaning up the code and using all the latest features of .NET 4.5 Changes 4.2.2 (2012-11-02) Improved handling of left clicks 4.1.0 (2012-10-17) Removed tray icon Assembly renamed and signed with strong name Note When you upgrade, Launchbar will start with the default settings. You can import your previous settings by following these steps: Run Launchbar and just save the settings without configuring anything Shutdown Launchbar Go to the folder %LOCA...CommonLibrary.NET: CommonLibrary.NET 0.9.8.8: Releases notes for FluentScript located at http://fluentscript.codeplex.com/wikipage?title=Release%20Notes&referringTitle=Documentation Fluentscript - 0.9.8.8 - Final ReleaseApplication: FluentScript Version: 0.9.8.8 Build: 0.9.8.8 Changeset: 77368 ( CommonLibrary.NET ) Release date: November 2nd, 2012 Binaries: CommonLibrary.dll Namespace: ComLib.Lang Project site: http://fluentscript.codeplex.com/ Download: http://commonlibrarynet.codeplex.com/releases/view/90426 Source code: http://common...Mouse Jiggler: MouseJiggle-1.3: This adds the much-requested minimize-to-tray feature to Mouse Jiggler.Umbraco CMS: Umbraco 4.10.0 Release Candidate: This is a Release Candidate, which means that if we do not find any major issues in the next week, we will release this version as the final release of 4.10.0 on November 9th, 2012. The documentation for the MVC bits still lives in the Github version of the docs for now and will be updated on our.umbraco.org with the final release of 4.10.0. Browse the documentation here: https://github.com/umbraco/Umbraco4Docs/tree/4.8.0/Documentation/Reference/Mvc If you want to do only MVC then make sur...Skype Auto Recorder: SkypeAutoRecorder 1.3.4: New icon and images. Reworked settings window. Implemented high-quality sound encoding. Implemented a possibility to produce stereo records. Added buttons with system-wide hot keys for manual starting and canceling of recording. Added buttons for opening folder with records. Added Help button. Fixed an issue when recording is continuing after call end. Fixed an issue when recording doesn't start. Fixed several bugs and improved stability. Major refactoring and optimization...Access 2010 Application Platform - Build Your Own Database: Application Platform - 0.0.2: Release 0.0.2 Created two new users. One belongs to the Administrators group and the other to the Public group. User: admin Pass: admin User: guest Pass: guest Initial Release This is the first version of the database. At the moment is all contained in one file to make development easier, but the obvious idea would be to split it into Front and Back End for a production version of the tool. The features it contains at the moment are the "Core" features.Python Tools for Visual Studio: Python Tools for Visual Studio 1.5: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 RTM. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, HPC, IPython, etc. support. For a quick overview of the general IDE experience, please watch this video There are a number of exciting improvement in this release comp...BCF.Net: BCF.Net: BCF.Net-20121024 source codeAssaultCube Reloaded: 2.5.5: Linux has Ubuntu 11.10 32-bit precompiled binaries and Ubuntu 10.10 64-bit precompiled binaries, but you can compile your own as it also contains the source. If you are using Mac or other operating systems, please wait while we try to package for those OSes. Try to compile it. If it fails, download a virtual machine. The server pack is ready for both Windows and Linux, but you might need to compile your own for Linux (source included) Changelog: Fixed potential bot bugs: Map change, OpenAL...Edi: Edi 1.0 with DarkExpression: Added DarkExpression theme (dialogs and message boxes are not completely themed, yet)DirectX Tool Kit: October 30, 2012 (add WP8 support): October 30, 2012 Added project files for Windows Phone 8MCEBuddy 2.x: MCEBuddy 2.3.6: Changelog for 2.3.6 (32bit and 64bit) 1. Fixed a bug in multichannel audio conversion failure. AAC does not support 6 channel audio, MCEBuddy now checks for it and force the output to 2 channel if AAC codec is specified 2. Fixed a bug in Original Broadcast Date and Time. Original Broadcast Date and Time is reported in UTC timezone in WTV metadata. TVDB and MovieDB dates are reported in network timezone. It is assumed the video is recorded and converted on the same machine, i.e. local timezone...MVVM Light Toolkit: MVVM Light Toolkit V4.1 for Visual Studio 2012: This version only supports Visual Studio 2012 (and all Express editions too). If you use Visual Studio 2010, please stay tuned, we will publish an update in a few days with support for VS10. V4.1 supports: Windows Phone 8 Windows 8 (Windows RT) Silverlight 5 Silverlight 4 WPF 4.5 WPF 4 WPF 3.5 And the following development environments: Visual Studio 2012 (Pro, Premium, Ultimate) Visual Studio 2012 Express for Windows 8 Visual Studio 2012 Express for Windows Phone 8 Visual...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.73: Fix issue in Discussion #401101 (unreferenced var in a for-in statement was getting removed). add the grouping operator to the parsed output so that unminified parsed code is closer to the original. Will still strip unneeded parens later, if minifying. more cleaning of references as they are minified out of the code.RiP-Ripper & PG-Ripper: PG-Ripper 1.4.03: changes NEW: Added Support for the phun.org forum FIXED: Kitty-Kats new Forum UrlLiberty: v3.4.0.1 Release 28th October 2012: Change Log -Fixed -H4 Fixed the save verification screen showing incorrect mission and difficulty information for some saves -H4 Hopefully fixed the issue where progress did not save between missions and saves would not revert correctly -H3 Fixed crashes that occurred when trying to load player information -Proper exception dialogs will now show in place of crashesPlayer Framework by Microsoft: Player Framework for Windows 8 (Preview 7): This release is compatible with the version of the Smooth Streaming SDK released today (10/26). Release 1 of the player framework is expected to be available next week. IMPROVEMENTS & FIXESIMPORTANT: List of breaking changes from preview 6 Support for the latest smooth streaming SDK. Xaml only: Support for moving any of the UI elements outside the MediaPlayer (e.g. into the appbar). Note: Equivelent changes to the JS version due in coming week. Support for localizing all text used in t...Send multiple SMS via Way2SMS C#: SMS 1.1: Added support for 160by2Quick Launch: Quick Launch 1.0: A Lightweight and Fast Way to Manage and Launch Thousands of Tools and ApplicationsPress Win+Q and start to search and run. http://www.codeplex.com/Download?ProjectName=quicklaunch&DownloadId=523536New Projectsappnitiren: This project's main objective is to deepen my knowledge on developing apps for windows 8 and windows phone and Buddhist philosophy of Nichiren Daishonin. Aspect - TypeScript AOP Framework: A simple AOP framework for TypeScript.AWF's PowerPoint Tab: A collection of little powerpoint utilities, including "resize all shapes".Base64 Encoder-Decoder: (Base64 Encoder/Decoder using C#)BombaJob-WF: Official Windows desktop client for BombaJob.bgBungie Test: !CCAudio: A project to create an audio recording/mixing and processing framework in C#/C++ with a look to creating a Digital Audio Workstation. EvaluationSyarem: for yuanguangexporttfschangesets: Small utility that runs agains tftp.exe(tfs power tools) and exports a given range of changesets.fjfdszjtfs: fjfdszjtfsKladionica: Ovo je mala web aplikacija koja je specijalizovana za f1 kladionicu na forumu KrstaricaListViewItem Float Test: WPF testing ground for development of a "floating" listviewitem (preeettty)Macconnell: This is my test projectNWebsec Demo site: This is the NWebsec demo website project.Ocean Flattened: Summary of this projectQuagmire: QUAGMIRE aims to make distributed data processing and visualisation simple and flexible.Scheduled SQL Jobs for DotNetNuke by IowaComputerGurus Inc.: Keeping a DotNetNuke site database clean can be a real nightmare for those hosting sites on shared hosting providers.Secretary Tool: Tool for secretaries of congregations of Jehovah's Witnesses.Secure My Install for DotNetNuke by IowaComputerGurus: This module is a single-use per DotNetNuke installation utility module that will make a number of security enhancing modifications to your "out of the box" DotNServStop: ServStop is a .NET application that makes it easy to stop several system services at once. Now you don't have to change startup types or stop them one at a time. It has a simple list-based interface with the ability to save and load lists of user services to stop. Written in C#.Simple File List for DotNetNuke by IowaComputerGurus Inc.: The Simple File List module is a Free DotNetNuke module that will list all files within a specific folder under the specific portal folder within DNN for users SOLUS3 Config Discovery: An open-source community developed tool for generating a simple text file detailing your local SIMS server settings to simplify new SOLUS3 configurations.Sort Project: Project Name: Sort Project Description: This project holds a class that extends objects type of IEnumerable by enabling them using sorting algorithms other than the buil in one within the microsoft staff SQL Azure Data Protector: This tool leverages the currently available options that Azure platform has to provide an integrated and automated solution to back up the SQL Azure databases.Throttling Suite for ASP.NET Applications: The Throttling Suite provides throttling control capabilities to the ASP.NET applications. It is highly customizable; including "log-only" mode.TidyBackups: Allows for automation of deletion of Microsoft SQL backup files based on file type (.bak) creation age as well as compression using standard ZIP technology.TrainingData: TrainingData is a set of libraries for reading and modifying training data files for Garmin and Polar heart rate monitors.Virtual eCommerce: ??? ? ?????? ????????? ??????. ??????: ??????????? ?????????, ?????????? ?????????? ?? ????????????? ?? Microsoft - ASP Web Pages with Razor Engine.WebNext: My personal web page / blog with cms on asp mvc 3Windows 8 Mouse Unsticky: Makes Windows 8 top right/left hot corners unsticky.WPForms: WPForms is simple framework for Form-driven Silverlight Windows Phone applications. Using the framework allows developers to easily create and display forms.

  Read the article

• How to get sound on macbook pro 4,1

  - by Thomas

  I have just installed Xubuntu 12.04.2. My soundcard is detected: thomas@thomas-pc:~$ sudo aplay -l **** List of PLAYBACK Hardware Devices **** Home directory /home/thomas not ours. card 0: Intel [HDA Intel], device 0: ALC889A Analog [ALC889A Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC889A Digital [ALC889A Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 Everything is put to max in alsamixer and nothing is muted (all the sliders are on OO. My speakers do not work, but when I plug in a headphone I hear it very soft. When I connect my stereo and put the sound VERY loud (3-blocks-of-complaining-neighbours loud) I hear it on a normal level but crackling. I added options snd-hda-intel model=mbp5 amixer set IEC958 off to at the end of /etc/modprobe.d/alsa-base.conf. When it's still not working I tried everything here: https://help.ubuntu.com/community/SoundTroubleshooting 1 >>> list-sinks 1 sink(s) available. * index: 0 name: <alsa_output.pci-0000_00_1b.0.analog-stereo> driver: <module-alsa-card.c> flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY DYNAMIC_LATENCY state: SUSPENDED suspend cause: IDLE priority: 9959 volume: 0: 100% 1: 100% 0: 0.00 dB 1: 0.00 dB balance 0.00 base volume: 100% 0.00 dB volume steps: 65537 muted: no current latency: 0.00 ms max request: 0 KiB max rewind: 0 KiB monitor source: 0 sample spec: s16le 2ch 44100Hz channel map: front-left,front-right Stereo used by: 0 linked by: 0 configured latency: 0.00 ms; range is 0.50 .. 371.52 ms card: 0 <alsa_card.pci-0000_00_1b.0> module: 4 properties: alsa.resolution_bits = "16" device.api = "alsa" device.class = "sound" alsa.class = "generic" alsa.subclass = "generic-mix" alsa.name = "ALC889A Analog" alsa.id = "ALC889A Analog" alsa.subdevice = "0" alsa.subdevice_name = "subdevice #0" alsa.device = "0" alsa.card = "0" alsa.card_name = "HDA Intel" alsa.long_card_name = "HDA Intel at 0x9b500000 irq 46" alsa.driver_name = "snd_hda_intel" device.bus_path = "pci-0000:00:1b.0" sysfs.path = "/devices/pci0000:00/0000:00:1b.0/sound/card0" device.bus = "pci" device.vendor.id = "8086" device.vendor.name = "Intel Corporation" device.product.name = "82801H (ICH8 Family) HD Audio Controller" device.form_factor = "internal" device.string = "front:0" device.buffering.buffer_size = "65536" device.buffering.fragment_size = "32768" device.access_mode = "mmap+timer" device.profile.name = "analog-stereo" device.profile.description = "Analog Stereo" device.description = "Built-in Audio Analog Stereo" alsa.mixer_name = "Realtek ALC889A" alsa.components = "HDA:10ec0885,106b3a00,00100103" module-udev-detect.discovered = "1" device.icon_name = "audio-card-pci" ports: analog-output-speaker: Speakers (priority 10000, available: unknown) properties: analog-output-headphones: Headphones (priority 9000, available: no) properties: active port: <analog-output-speaker> 2 and 3: Doesn't seem an permission issue, the sound is very far away (See opening paragraph). 4 thomas@thomas-pc:~$ sudo aplay -l **** List of PLAYBACK Hardware Devices **** Home directory /home/thomas not ours. card 0: Intel [HDA Intel], device 0: ALC889A Analog [ALC889A Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC889A Digital [ALC889A Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 5 thomas@thomas-pc:~$ find /lib/modules/`uname -r` | grep snd /lib/modules/3.2.0-48-generic/kernel/sound/core/snd-hwdep.ko /lib/modules/3.2.0-48-generic/kernel/sound/core/snd-pcm.ko [.. huge lists continues ..] /lib/modules/3.2.0-48-generic/kernel/sound/pcmcia/pdaudiocf/snd-pdaudiocf.ko /lib/modules/3.2.0-48-generic/kernel/sound/pcmcia/vx/snd-vxpocket.ko thomas@thomas-pc:~$ 6 thomas@thomas-pc:~$ lspci -v | grep -A7 -i "audio" 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03) Subsystem: Apple Inc. Device 00a4 Flags: bus master, fast devsel, latency 0, IRQ 46 Memory at 9b500000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 7 I guess it's supported. Linux mint and Xubuntu 13.04 had no trouble with sounds. Everything worked out of the box Thanks in advance Edit: alsa-info.sh output: WARNING: /etc/modprobe.d/alsa-base.conf line 45: ignoring bad line starting with 'amixer' ALSA Information Script v 0.4.62 -------------------------------- This script visits the following commands/files to collect diagnostic information about your ALSA installation and sound related hardware. dmesg lspci lsmod aplay amixer alsactl /proc/asound/ /sys/class/sound/ ~/.asoundrc (etc.) See './alsa-info.sh --help' for command line options. WARNING: /etc/modprobe.d/alsa-base.conf line 45: ignoring bad line starting with 'amixer' Automatically upload ALSA information to www.alsa-project.org? [y/N] : y Uploading information to www.alsa-project.org ... Done! Your ALSA information is located at http://www.alsa-project.org/db/?f=6cffc584284d4c0b266eb53249824ef83d6c4e3e Please inform the person helping you. thomas@thomas-pc:~$

  Read the article

• Create Orchard Module in a Separate Project

  - by Steve Michelotti

  The Orchard Project is a new OOS Microsoft project that is being developed up on CodePlex. From the Orchard home page on CodePlex, it states “Orchard project is focused on delivering a .NET-based CMS application that will allow users to rapidly create content-driven Websites, and an extensibility framework that will allow developers and customizers to provide additional functionality through modules and themes.” The Orchard Project site contains additional information including documentation and walkthroughs. The ability to create a composite solution based on a collection of modules is a compelling feature. In Orchard, these modules can just be created as simple MVC Areas or they can also be created inside of stand-alone web application projects.  The walkthrough for writing an Orchard module that is available on the Orchard site uses a simple Area that is created inside of the host application. It is based on the Orchard MIX presentation. This walkthrough does an effective job introducing various Orchard concepts such as hooking into the navigation system, theme/layout system, content types, and more.  However, creating an Orchard module in a separate project does not seem to be concisely documented anywhere. Orchard ships with several module OOTB that are in separate assemblies – but again, it’s not well documented how to get started building one from scratch. The following are the steps I took to successfully get an Orchard module in a separate project up and running. Step 1 – Download the OrchardIIS.zip file from the Orchard Release page. Unzip and open up the solution. Step 2 – Add your project to the solution. I named my project “Orchard.Widget” and used and “MVC 2 Empty Web Application” project type. Make sure you put the physical path inside the “Modules” sub-folder to the main project like this: At this point the solution should look like: Step 3 – Add assembly references to Orchard.dll and Orchard.Core.dll. Step 4 – Add a controller and view.  I’ll just create a Hello World controller and view. Notice I created the view as a partial view (*.ascx). Also add the [Themed] attribute to the top of the HomeController class just like the normal Orchard walk through shows it. Step 5 – Add Module.txt to the project root. The is a very important step. Orchard will not recognize your module without this text file present.  It can contain just the name of your module: name: Widget Step 6 – Add Routes.cs. Notice I’ve given an area name of “Orchard.Widget” on lines 26 and 33. 1: using System; 2: using System.Collections.Generic; 3: using System.Web.Mvc; 4: using System.Web.Routing; 5: using Orchard.Mvc.Routes; 6:   7: namespace Orchard.Widget 8: { 9: public class Routes : IRouteProvider 10: { 11: public void GetRoutes(ICollection<RouteDescriptor> routes) 12: { 13: foreach (var routeDescriptor in GetRoutes()) 14: { 15: routes.Add(routeDescriptor); 16: } 17: } 18:   19: public IEnumerable<RouteDescriptor> GetRoutes() 20: { 21: return new[] { 22: new RouteDescriptor { 23: Route = new Route( 24: "Widget/{controller}/{action}/{id}", 25: new RouteValueDictionary { 26: {"area", "Orchard.Widget"}, 27: {"controller", "Home"}, 28: {"action", "Index"}, 29: {"id", ""} 30: }, 31: new RouteValueDictionary(), 32: new RouteValueDictionary { 33: {"area", "Orchard.Widget"} 34: }, 35: new MvcRouteHandler()) 36: } 37: }; 38: } 39: } 40: } Step 7 – Add MainMenu.cs. This will make sure that an item appears in the main menu called “Widget” which points to the module. 1: using System; 2: using Orchard.UI.Navigation; 3:   4: namespace Orchard.Widget 5: { 6: public class MainMenu : INavigationProvider 7: { 8: public void GetNavigation(NavigationBuilder builder) 9: { 10: builder.Add(menu => menu.Add("Widget", item => item.Action("Index", "Home", new 11: { 12: area = "Orchard.Widget" 13: }))); 14: } 15:   16: public string MenuName 17: { 18: get { return "main"; } 19: } 20: } 21: } Step 8 – Clean up web.config. By default Visual Studio adds numerous sections to the web.config. The sections that can be removed are: appSettings, connectionStrings, authentication, membership, profile, and roleManager. Step 9 – Delete Global.asax. This project will ultimately be running from inside the Orchard host so this “sub-site” should not have its own Global.asax.   Now you’re ready the run the app.  When you first run it, the “Widget” menu item will appear in the main menu because of the MainMenu.cs file we added: We can then click the “Widget” link in the main menu to send us over to our view:   Packaging From start to finish, it’s a relatively painless experience but it could be better. For example, a Visual Studio project template that encapsulates aspects from this blog post would definitely make it a lot easier to get up and running with creating an Orchard module.  Another aspect I found interesting is that if you read the first paragraph of the walkthrough, it says, “You can also develop modules as separate projects, to be packaged and shared with other users of Orchard CMS (the packaging story is still to be defined, along with marketplaces for sharing modules).” In particular, I will be extremely curious to see how the “packaging story” evolves. The first thing that comes to mind for me is: what if we explored MvcContrib Portable Areas as a potential mechanism for this packaging? This would certainly make things easy since all artifacts (aspx, aspx, images, css, javascript) are all wrapped up into a single assembly. Granted, Orchard does have its own infrastructure for layouts and themes but it seems like integrating portable areas into this pipeline would not be a difficult undertaking. Maybe that’ll be the next research task. :)

  Read the article

• Configurer un module Scaime eNod3-C en CANopen sur M340 en Unity, par Bruno Guérangé

  Contrairement à la série TSX57 Premium, la gamme M340 de Schneider ne comporte pas de carte de pesage. Pour ajouter des voies de pesage sur une configuration il faut donc installer et raccorder des modules externes sur l'automate. Nous avons donc cherché des modules raccordables sur le réseau CANopen, CANopen est un bus de terrain ouvert et rapide, de plus il est intégré de série sur certaines CPU de la gamme M340. Un des modules connectable sur le réseau CANopen est le transmetteur de pesage Scaime eNod3-C. Scaime est une marque reconnue dans le domaine du pesage et le module eNod3-C présente de très bonnes caractéristiques de mesure et filtrage. ...

  Read the article

• What commands are needed to install Ubuntu Core?

  - by Oxwivi

  Ubuntu Core's wiki page page contains the instructions to install Ubuntu Core on a target media: Uncompress (do not unpack) rootfs Format target media: at least one partition should be ext2, ext3, or ext4 Unpack Ubuntu Core to ext{2,3,4} partition Install boot-loader Install Linux If the Linux kernel requires modules, add these to /lib/modules/$(uname -r) in the ext{2,3,4} file system Boot the target device Install any additional required software using apt-get But what are the specific commands to do the above? The things I'm specifically confused about are: Uncompressing and unpacking, what's the difference and how do I do them? What package should I install if I want the generic kernel provided in regular Ubuntu installation? I won't be installing any drivers or anything related to kernel other than what's provided in the repos, do I need to worry about manually adding kernel modules? PS I would like to request that all the commands used in the installation process be mentioned in the answer, for the benefit of ones who're completely unfamiliar and myself, should I ever forget.

  Read the article

• EBS Extensions for Endeca 12.2 V5 Now Available

  - by LuciaC-Oracle

  E-Business Suite Development has announced the availability of Oracle E-Business Suite Extensions for Oracle Endeca 12.2 V5 - see the announcement here.  This release adds the following new modules that can be used to extend Oracle E-Business Suite 12.2: Oracle Service Contracts Extensions for Oracle Endeca Oracle TeleService Extensions for Oracle Endeca Oracle Human Resources Extensions for Oracle Endeca Oracle Quality Extensions for Oracle Endeca. These new modules are in addition to those already previously available.  Availability of these new and updated V5 modules for 12.1 is planned. Where can I find more information? Subscribe to the YouTube channel for Oracle E-Business Suite to get the latest on Oracle E-Business Suite Extensions for Oracle Endeca. Bookmark the Information Center: Oracle E-Business Suite Extensions for Oracle Endeca (Doc ID 1486924.2) Read about how to install Oracle E-Business Suite Extensions for Oracle Endeca, Release 12.2 V5 (Doc ID 1614014.1).

  Read the article

• While installing updates I get "Package operation Failed" for ubuntu 12.04

  - by user54395

  i get the following response in the details:- Please help nstallArchives() failed: perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory (Reading database ... (Reading database ... 5%% (Reading database ... 10%% (Reading database ... 15%% (Reading database ... 20%% (Reading database ... 25%% (Reading database ... 30%% (Reading database ... 35%% (Reading database ... 40%% (Reading database ... 45%% (Reading database ... 50%% (Reading database ... 55%% (Reading database ... 60%% (Reading database ... 65%% (Reading database ... 70%% (Reading database ... 75%% (Reading database ... 80%% (Reading database ... 85%% (Reading database ... 90%% (Reading database ... 95%% (Reading database ... 100%% (Reading database ... 427340 files and directories currently installed.) Preparing to replace thunderbird-trunk-globalmenu 14.0~a1~hg20120409r9862.91177-0ubuntu1~umd1 (using .../thunderbird-trunk-globalmenu_14.0~a1~hg20120409r9866.91235-0ubuntu1~umd1_i386.deb) ... Unpacking replacement thunderbird-trunk-globalmenu ... Preparing to replace thunderbird-trunk 14.0~a1~hg20120409r9862.91177-0ubuntu1~umd1 (using .../thunderbird-trunk_14.0~a1~hg20120409r9866.91235-0ubuntu1~umd1_i386.deb) ... Unpacking replacement thunderbird-trunk ... Processing triggers for man-db ... locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for gnome-menus ... Processing triggers for desktop-file-utils ... Setting up crossplatformui (1.0.27) ... Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service acpid restart Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the stop(8) and then start(8) utilities, e.g. stop acpid ; start acpid. The restart(8) utility is also available. acpid stop/waiting acpid start/running, process 5286 package libqtgui4 exist QT_VERSION = 4 make -C /lib/modules/3.2.0-22-generic/build M=/usr/local/bin/ztemtApp/zteusbserial/below2.6.27 modules make[1]: Entering directory /usr/src/linux-headers-3.2.0-22-generic' CC [M] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.o /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:34:28: fatal error: linux/smp_lock.h: No such file or directory compilation terminated. make[2]: *** [/usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.o] Error 1 make[1]: *** [_module_/usr/local/bin/ztemtApp/zteusbserial/below2.6.27] Error 2 make[1]: Leaving directory/usr/src/linux-headers-3.2.0-22-generic' make: * [modules] Error 2 dpkg: error processing crossplatformui (--configure): subprocess installed post-installation script returned error exit status 2 No apport report written because MaxReports is reached already Setting up thunderbird-trunk (14.0~a1~hg20120409r9866.91235-0ubuntu1~umd1) ... Setting up thunderbird-trunk-globalmenu (14.0~a1~hg20120409r9866.91235-0ubuntu1~umd1) ... Errors were encountered while processing: crossplatformui Error in function: SystemError: E:Sub-process /usr/bin/dpkg returned an error code (1) Setting up crossplatformui (1.0.27) ... Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service acpid restart Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the stop(8) and then start(8) utilities, e.g. stop acpid ; start acpid. The restart(8) utility is also available. acpid stop/waiting acpid start/running, process 5541 package libqtgui4 exist QT_VERSION = 4 make -C /lib/modules/3.2.0-22-generic/build M=/usr/local/bin/ztemtApp/zteusbserial/below2.6.27 modules make[1]: Entering directory /usr/src/linux-headers-3.2.0-22-generic' CC [M] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.o /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:34:28: fatal error: linux/smp_lock.h: No such file or directory compilation terminated. make[2]: *** [/usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.o] Error 1 make[1]: *** [_module_/usr/local/bin/ztemtApp/zteusbserial/below2.6.27] Error 2 make[1]: Leaving directory/usr/src/linux-headers-3.2.0-22-generic' make: * [modules] Error 2 dpkg: error processing crossplatformui (--configure): subprocess installed post-installation script returned error exit status 2

  Read the article

• Choice the project pattern, advice for this case

  - by Lucas Rodrigues Sena

  I have a project in MVC4 entity framework, and have to adapt it to possible updates on the dlls and system do not stop work. I'm using portable Areas, but have difficulty creating 5 modules and about 5 functionality for each modules with fully functioning independently as a dll and database. 1- Reflection DLLs, the system works "on the fly". (I cant do it on mvc4 at moment). 2- Portables Areas (I need to do one area for each modules*functionality 5*5 Areas). Confuse way and I'm afraid if this is ridiculous. 3- Implement WFC on MVC4, compatible? 4- Other better way?

  Read the article

• Simple Project Templates

  - by Geertjan

  The NetBeans sources include a module named "simple.project.templates": In the module sources, Tim Boudreau turns out to be the author of the code, so I asked him what it was all about, and if he could provide some usage code. His response, from approximately this time last year because it's been sitting in my inbox for a while, is below. Sure - though I think the javadoc in it is fairly complete.  I wrote it because I needed to create a bunch of project templates for Javacard, and all of the ways that is usually done were grotesque and complicated.  I figured we already have the ability to create files from templates, and we already have the ability to do substitutions in templates, so why not have a single file that defines the project as a list of file templates to create (with substitutions in the names) and some definitions of what should be in project properties. You can also add files to the project programmatically if you want.Basically, a template for an entire project is a .properties file.  Any line which doesn't have the prefix 'pp.' or 'pvp.' is treated as the definition of one file which should be created in the new project.  Any such line where the key ends in * means that file should be opened once the new project is created.  So, for example, in the nodejs module, the definition looks like: {{projectName}}.js*=Templates/javascript/HelloWorld.js .npmignore=node_hidden_templates/npmignore So, the first line means:  - Create a file with the same name as the project, using the HelloWorld template    - I.e. the left side of the line is the relative path of the file to create, and the right side is the path in the system filesystem for the template to use       - If the template is not one you normally want users to see, just register it in the system filesystem somewhere other than Templates/ (but remember to set the attribute that marks it as a template)  - Include that file in the set of files which should be opened in the editor once the new project is created. To actually create a project, first you just create a new ProjectCreator: ProjectCreator gen = new ProjectCreator( parentFolderOfNewProject ); Now, if you want to programmatically generate any files, in addition to those defined in the template, you can: gen.add (new FileCreator("nbproject", "project.xml", false) {     public DataObject create (FileObject project, Map<String,String> substitutions) throws IOException {          ...     } }); Then pass the FileObject for the project template (the properties file) to the ProjectCreator's createProject method (hmm, maybe it should be the string path to the project template instead, to save the caller trouble looking up the FileObject for the template).  That method looks like this: public final GeneratedProject createProject(final ProgressHandle handle, final String name, final FileObject template, final Map<String, String> substitutions) throws IOException { The name parameter should be the directory name for the new project;  the map is the strings you gathered in the wizard which should be used for substitutions.  createProject should be called on a background thread (i.e. use a ProgressInstantiatingIterator for the wizard iterator and just pass in the ProgressHandle you are given). The return value is a GeneratedProject object, which is just a holder for the created project directory and the set of DataObjects which should be opened when the wizard finishes. I'd love to see simple.project.templates moved out of the javacard cluster, as it is really useful and much simpler than any of the stuff currently done for generating projects.  It would also be possible to do much richer tools for creating projects in apisupport - i.e. choose (or create in the wizard) the templates you want to use, generate a skeleton wizard with a UI for all the properties you'd like to substitute, etc. Here is a partial project template from Javacard - for example usage, see org.netbeans.modules.javacard.wizard.ProjectWizardIterator in javacard.project (or the much simpler one in contrib/nodejs). #This properties file describes what to create when a project template is#instantiated.  The keys are paths on disk relative to the project root. #The values are paths to the templates to use for those files in the system#filesystem.  Any string inside {{ and }}'s will be substituted using properties#gathered in the template wizard.#Special key prefixes are #  pp. - indicates an entry for nbproject/project.properties#  pvp. - indicates an entry for nbproject/private/private.properties #File templates, in format [path-in-project=path-to-template]META-INF/javacard.xml=org-netbeans-modules-javacard/templates/javacard.xmlMETA-INF/MANIFEST.MF=org-netbeans-modules-javacard/templates/EAP_MANIFEST.MF APPLET-INF/applet.xml=org-netbeans-modules-javacard/templates/applet.xmlscripts/{{classnamelowercase}}.scr=org-netbeans-modules-javacard/templates/test.scrsrc/{{packagepath}}/{{classname}}.java*=Templates/javacard/ExtendedApplet.java nbproject/deployment.xml=org-netbeans-modules-javacard/templates/deployment.xml#project.properties contentspp.display.name={{projectname}}pp.platform.active={{activeplatform}} pp.active.device={{activedevice}}pp.includes=**pp.excludes= I will be using the above info in an upcoming blog entry and provide step by step instructions showing how to use them. However, anyone else out there should have enough info from the above to get started yourself!

  Read the article

< Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >