Search Results

Search found 44763 results on 1791 pages for 'first responder'.

Page 360/1791 | < Previous Page | 356 357 358 359 360 361 362 363 364 365 366 367  | Next Page >

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Windows Phone sync error when syncing with iTunes on different Hard Drive

  - by njallam

  I have my iTunes library file on a separate hard drive (which I believe may be the cause of the problem) and I have been trying to use it to synchronize with my Windows Phone. I would like to first note that if I set up my phone to synchronize with 'Windows Libraries', then it works fine. This is however not ideal as I have categorised my music and made playlists etc, on iTunes. When I first link my Windows Phone to the Windows Phone App (for desktop) and select iTunes from the above selection, I get the following error message: After searching that error, I found the following forum threads: Fix for error 8300300B when trying to sync Lumia 920 Windows 8 Phone in PC? Error code 8300300B on Windows Phone 8 while trying to sync I've tried the workarounds described in the above threads, however, they did not work for me. If I ignore that error message, I see the expected interface, along with all of my iTunes library's media, however the 'Sync' button is greyed out. I have tried some other things to try and fix this: Removing the app's AppData folder Uninstalling, reinstalling Using the full-screen modern app (does not allow for iTunes syncing)

  Read the article

• Incorrect durations mp4 file created by ffmpeg (avconv)

  - by Ruslan Sharipov

  Example usage: avconv -i rtmp://maps.lo.ufanet.ru/live/10e227922b473e91f37474fa084107af -vcodec copy -an -sn -map 0 -f segment -segment_format mp4 -segment_time 60 -y %05d.mp4 avconv version 0.8.3-6:0.8.3-1+b1, Copyright (c) 2000-2012 the Libav developers built on Jun 15 2012 13:54:35 with gcc 4.7.0 HandShake: client signature does not match! Metadata: height 480.00 remote_addr: sdp_session {sdp_session,0, {sdp_o,"-","1289703354974145","1289703354974145",inet4, "10.1.12.99"}, "Media Presentation", {inet4,"0.0.0.0"}, {0,0}, [{"control","*"},{"range","npt=0.0 start 30400239.52 timeshift_duration 319250.58 timeshift_size 120000.00 width 640.00 [flv @ 0x1d36a40] Estimating duration from bitrate, this may be inaccurate Input #0, flv, from 'rtmp://maps.lo.ufanet.ru/live/10e227922b473e91f37474fa084107af': Duration: N/A, start: 0.000000, bitrate: N/A Stream #0.0: Video: h264 (Baseline), yuvj420p, 640x480 [PAR 1:1 DAR 4:3], 1k tbr, 1k tbn, 2k tbc Output #0, segment, to '%05d.mp4': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: libx264, yuvj420p, 640x480 [PAR 1:1 DAR 4:3], q=2-31, 1k tbn, 1k tbc Stream mapping: Stream #0:0 -> #0:0 (copy) Press ctrl-c to stop encoding ^Cframe= 9566 fps= 36 q=-1.0 Lsize= -0kB time=318.25 bitrate= -0.0kbits/s video:30348kB audio:0kB global headers:0kB muxing overhead -100.000071% Received signal 2: terminating. Result: serafim@yard:~/video2$ ls 00000.mp4 00001.mp4 00002.mp4 00003.mp4 00004.mp4 00005.mp4 Now try to play the files in the player, such as VLC. And that's what we get: the first fragment (00000.mp4) played well, no problems, but the second (00001.mp4 and beyond) starts the bug manifests itself, namely the file 00001.mp4 first 60 seconds black screen, but since 61 seconds starts playing the video. Attachments: https://dl.dropbox.com/u/760901/rtmp_and_mp4.zip How to get rid of the delay with black screen at the beginning of the segments? Maybe ffmpeg to pass parameters, or third-party software is able to correct the obtained segments mp4?

  Read the article

• How to change the spell checking language in Chromium?

  - by mote

  When write I need spell checking in Danish or English (one at a time, not both at the same time), but changing from one language to the other is not working well for me. Example: Writing an email in English, everything is underlined as misspelled because the spelling language is set to Danish. I then right-click the text field and choose "Spell-checker Options" and set the language to English. But is does not change the language. Only after I try maybe 4-5 times it does. Selecting the text, clicking it, clicking the background, click the text, I have tried it all but I cannot figure out how it works. Sometimes it changes on first try, sometimes I have to do it 6-7 times. Searching brings lots of a known bugs stating that Chromium does not re-check the text after changing the language. But that is not what drives me crazy, for starters being able to change the language in the first try would be nice. It is not a fault in my installation, I have the same problem on 3 computers. Does any know something that I don't?

  Read the article

• Comparing 2 (or 3 Files If Possible) "Line By Line"

  - by PythEch

  I want to find out the differences of 2 (or 3 files if possible) line by line. Diff utils can do this, however it gives inaccurate results. Because, 2 files have exact number of lines which is "134". But diff gives me "Added Lines" and "Removed Lines". However this is wrong, they have exact the same number of lines, there is no added or removed lines. The text files which I want to find differences of them, have only numbers written, maybe that's why that algortihm fails. I couldn't find any option to prevent that, however I may be wrong, I mean there should be an option for that, but again, I couldn't find. This is what I get (5am.txt vs 6am.txt, there is a huge problem): This is what I want (6am.txt vs 7am.txt, still has problems): But, first the first image still has this problem, at the last lines. Edit: After I figured out that there is no utility to do this, I handled myself. I almost did the same thing as what RedGrittyBrick have done. This script imitates diff utility so I (or you) can use it with diff2html. To use it with diff2html, just change line diff_stdout = os.popen("diff %s" % string.join(argv[1:]), "r") to diff_stdout = os.popen("script.py %s" % string.join(argv[1:]), "r") and name this script whatever you want: import sys f1=open(sys.argv[1],"r") f1_read=f1.readlines() f1.close() f2=open(sys.argv[2],"r") f2_read=f2.readlines() f2.close() changed={} first_c = "" for n in range(len(f1_read)): if f1_read[n]!=f2_read[n]: if first_c == "": first_c=n+1 changed[first_c]=n+1 else: first_c="" #Let's imitate diff-utils... for (x, y) in changed.items(): print "%d,%dc%d,%d" % (x,y,x,y) for i in range(x,y+1): sys.stdout.write("< %s" % f1_read[i-1]) print "---" for i in range(x,y+1): sys.stdout.write("> %s" % f2_read[i-1]) Final results:

  Read the article

• Very high-pitched noise when computer does something intense?

  - by Starkers

  "Intense" is the best word I can use to describe it because I'm not sure what it is, whether it's RAM, GPU or CPU. If I pan the camera in unity: A high pitched noise issues from the computer. The picosecond I start panning the sound starts. Stops the picosecond I stop panning. If I start an infinite loop: 2.0.0p247 :016 > x = 1 => 1 2.0.0p247 :017 > while x < 2 do 2.0.0p247 :018 > puts 'huzzah!' 2.0.0p247 :019?> end huzzah! huzzah! huzzah! An identical high pitched noise can be heard. I don't think it's the GPU due to this simple experiment. Or any monitor-weirdness (although the sound does sound like one of those old CRT monitors if you're old enough to be young when those things were about) The CPU? Or maybe my SSD? It's my first SSD and the first time I've heard this noise. Should I be worried? Regardless, what's causing this sound? I can't think what would cause such high frequency vibrations. I built the PC myself. Not enough heat paste on the CPU? Too much? Just no idea what's going on. Info: CPU Type QuadCore Intel Core i5-3570K, 3800 MHz (38 x 100) Motherboard Name Asus Maximus V Extreme Flash Memory Type Samsung 21nm TLC NAND Video Adapter Asus HD7770

  Read the article

• XCOPY access denied error on My Documents folder

  - by Ryan M.

  Here's the situation. We have a file server set up at \fileserver\ that has a folder for every user at \fileserver\users\first.last I'm running an xcopy command to backup the My Documents folder from their computer to their personal folder. The command I'm running is: xcopy "C:\Users\%username%\My Documents\*" "\\fileserver\users\%username%\My Documents" /D /E /O /Y /I I've been silently running this script at login without the users knowing, just so I can get it to work before telling them what it does. After I discovered it wasn't working, I manually ran the batch script that executes the xcopy command on one of their computers and get an access denied error. I then logged into a test account on my own computer and got the same error. I checked all the permissions for the share and security and they're set to how I want them. I can manually browse to that folder and create new files. I can drag and drop items into the \fileserver\users\first.last location and it works great. So I try something else to try and find the source of the access denied problem. I ran an xcopy command to copy the My Documents folder to a different location on the same machine and I still got the access denied error! So xcopy seems to be denied access when it tries to copy the My Documents folder. Any suggestions on how I can get this working? Anyone know the reason behind the access denied error?

  Read the article

• Virtualbox port forwarding with iptables

  - by jverdeyen

  I'm using a virtualmachine (virtualbox) as mailserver. The host is an Ubuntu 12.04 and the guest is an Ubuntu 10.04 system. At first I forwarded port 25 to 2550 on the host and added a port forward rule in VirtualBox from 2550 to 25 on the guest. This works for all ports needed for the mailserver. The guest has a host only connection and a NAT (with the port-forwarding). My mailserver was receiving and sending mail properly. But all connections are comming from the virtualbox internal ip, so every host connection is allowed, and that's not what I want. So.. I'm trying to skip the VirtualBox forwarding part and just forward port 25 to my host only ip of the guest system. I used these rules: iptables -F iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT iptables -P FORWARD ACCEPT iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -A INPUT --protocol tcp --dport 25 -j ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -s 192.168.99.0/24 -i vboxnet0 -j ACCEPT echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -A PREROUTING -p tcp -i eth0 -d xxx.host.ip.xxx --dport 25 -j DNAT --to 192.168.99.105:25 iptables -A FORWARD -s 192.168.99.0/24 -i vboxnet0 -p tcp --dport 25 -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.99.0 -o eth0 -j MASQUERADE iptables -L -n But after these changes I still can't connect with a simple telnet. (Which was possible with my first solution). The guest machine doesn't have any firewall. I only have one network interface on the host (eth0) and a host interface (vboxnet0). Any suggestions? Or should I go back to my old solution (which I don't really like). Edit: bridge mode isn't an option, I have only on IP available for the moment. Thanks!

  Read the article

• windows 7 turns off itself everyday at about 9am

  - by Radek

  I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

  Read the article

• Recovering a mdadm+lvm+ext4 partition with read error

  - by bitwelder

  One of disks in my NAS has failed. The NAS is running Linux, and it uses mdadm + LVM technology for its filesystems. I do have backup for most of the contents, but not for the very last changes, and if possible, I'd like to recover that from this failing disk. The disk (a 'green drive' WD10EARS 1TB in size) throws this kind of errors: Oct 3 12:00:41 kernel: [ 3625.620000] ata5.00: read unc at 9453282 Oct 3 12:00:41 kernel: [ 3625.620000] lba 9453282 start 9453280 end 1953511007 Oct 3 12:00:41 kernel: [ 3625.620000] sde5 auto_remap 0 Oct 3 12:00:41 kernel: [ 3625.630000] ata5.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 Oct 3 12:00:41 kernel: [ 3625.630000] ata5.00: edma_err_cause=00000084 pp_flags=00000003, dev error, EDMA self-disable Oct 3 12:00:41 kernel: [ 3625.640000] ata5.00: failed command: READ FPDMA QUEUED Oct 3 12:00:41 kernel: [ 3625.650000] ata5.00: cmd 60/40:00:e0:3e:90/00:00:00:00:00/40 tag 0 ncq 32768 in Oct 3 12:00:41 kernel: [ 3625.650000] res 41/40:00:e2:3e:90/12:00:00:00:00/40 Emask 0x409 (media error) <F> Oct 3 12:00:41 kernel: [ 3625.660000] ata5.00: status: { DRDY ERR } However, while testing with 'dd', I noticed that if I skip the first 4kB, the read seems to be ok, i.e. a command like. dd if=/dev/sde5 of=dev/null bs=4k count=1000 skip=1 doesn't return any read error. Supposing that there is no other read failure in the rest of the disk, would I be able to recover this 900 GB partition (as I mentioned before, it's a 'linux raid autodetect' partition, that contains a a LVM2 volume that contains a ext4 filesystem) if I copy-clone the partition somewhere else, but the first 4kB?

  Read the article

• OpenLDAP ACLs are not working

  - by Dr I

  First things first, I'm currently working with an OpenLDAP: slapd 2.4.36 on a Fedora release 19 (Schrödinger’s Cat). I've just install the openldap with yum and my configuration is the following one: ##### OpenLDAP Default configuration ##### # ##### OpenLDAP CORE CONFIGURATION ##### include /etc/openldap/schema/core.schema include /etc/openldap/schema/cosine.schema include /etc/openldap/schema/inetorgperson.schema include /etc/openldap/schema/nis.schema pidfile /var/lib/ldap/slapd.pid loglevel trace ##### Default Schema ##### database mdb directory /var/lib/ldap/ maxsize 1073741824 suffix "dc=domain,dc=tld" rootdn "cn=root,dc=domain,dc=tld" rootpw {SSHA}SECRETP@SSWORD ##### Default ACL ##### access to attrs=userpassword by self write by group.exact="cn=administrators,ou=builtin,ou=groups,dc=domain,dc=tld" write by anonymous auth by * none I launch my OpenLDAP service using: /usr/sbin/slapd -u ldap -h ldapi:/// ldap:/// -f /etc/openldap/slapd.conf As you can see it's a pretty simple ACL which aim to allow access to the userPassword attribute to a specific group read only, then to the owner read and write to anonymous requiring auth and refuse the access to everyone else. The problem is: Even using a valid user with correct password my ldapsearch ends with zero informations retrieved from the directory, plus I've got a strange response on the result line. # search result search: 2 result: 32 No such object # numResponses: 1 here is the ldapsearch request: ldapsearch -H ldap.domain.tld -W -b dc=domain,dc=tld -s sub -D cn=user,ou=service,ou=employees,ou=users,dc=domain,dc=tld I did not specify any filter as I want to check that ldapsearch is correctly printing only allowed attribute.

  Read the article

• Exchange 2007 - Mailbox Database Recovery

  - by Phrontiste

  Exchange 2007 edb Can we restore Exchange edb (First storage group\mailbox database.edb) to another exchange server ? Do I just copy the edb to the new exchange server and delete the first storage group\mailbox database.edb and replace it with this one ? How can I get all the mailboxes from that (old) mailbox database.edb ? I had a exchange 2007 server with 10 mailboxes, I have installed exchange on another machine and was thinking if I can do the above ? or is there any way I can get all the mailboxes from that edb (old mailbox database) and import them into the new one. I have deleted the old exchange install I had (these are test machines) What are the steps required to get the DB working on the new machine ? Also, I am confused about the recovery storage group ? I can mount a mailbox database in recovery storage group, but when I try to get mailbox out of it, it won't match any thing ? can someone please assist in understanding RSG and how to restore the OLD mailbox database. thanks and regards Phrontiste

  Read the article

• Slackware - Assigning routes (IP address ranges) to one of many network adapters

  - by Dogbert

  I am using a Slackware 13.37 virtual machine within VirtualBox (current). I currently have a number of Ubuntu VMs on a single server, along with this Slackware VM. All VMs have been set up to use "Internal Network" mode, so they are all on a private LAN, and can see each other (ie: share files amongst themselves), but they remain private from the outside world. On on the these VMs (the Slackware one), I need to be able to grant it access to both this private network, and the internet at large. The first suggestion I found for handling this is to add another virtual network adapter to the VM, then set it to NAT. This results in the Slackware VM having the following network adapter setup: -NIC#1: Internal Network -NIC#2: NAT I want to set up the first network adapter (NIC#1) to handle all traffic on the following subnets: 10.10.0.0/255.255.0.0 192.168.1.0/255.255.255.0 And I want the second virtual network adapter (NIC#2) to handle everything else (ie: internet access). May I please have some assistance in setting this up on my Slackware VM? Additionally, I have searched for similar questions on SuperUser and Stackoverflow, but they all seem to pertain to my situation (ie: they all refer to OSX, or Ubuntu via the use of some UI-based tool). I'm trying to do this on Slack specifically via the command-line. Thanks!

  Read the article

• Ubuntu and Windows and Separate HDs, oh my!

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. Here's a pic of the error I get when I try to boot to Windows: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu. (Someone suggested just reinstalling windows from installation CD. Agree?)

  Read the article

• How to avoid sshfs freezing?

  - by Andreas Hagen

  So the issue is this: I've installed sshfs on Ubuntu 12.04 and I'm trying to connect to a couple of remote servers. So initially the mount seams successful. Sometimes Gnome even picks it up and displays the "new device found" box at the bottom of the screen. but from here on there is not much that works. Or at least not any more. The first couple of times i connected it seamed to work fine, and I was able to transfer some files, then i disconnected using fusermount -u <folder> and after reconnecting a little later the trouble started. Now after executing sshfs -o ServerAliveInterval=15 -o reconnect -C -o workaround=all -o idmap=user root@<host>:/ <folder>, when I change directory into the mount-point, the shell just freezes. Strangely ls -al <folder> works when listing just the root of the remote system, but nothing more. Also every file-explorer I've tried freezes just like cd <folder>. To me it seamed like there was some kind of zombie thread or something hanging around my system, due to the fact that it did work the first time, so I have tried rebooting but no luck. sshfs -V gives this: SSHFS version 2.3 FUSE library version: 2.8.6 fusermount version: 2.8.6 using FUSE kernel interface version 7.12 So yea, any ideas?

  Read the article

• SendMail not working in CentOs 6.4

  - by Kane

  I am trying to send e-mails from my CentOS 6.4 but it does not work. My knowledge about servers is quite limited, so I hope someone can help me. Here is what I did: First i tried to send an email using the "mail" command, but it was not in the OS so I installed it. # yum install mailx After that, I tried sending an email using the "mail" command, but it did not send anything. I checked it on the internet and I realized I needed an e-mail server like sendmail, so I installed it. # yum install sendmail sendmail-cf sendmail-doc sendmail-devel After that, I configured it following some tutorials. First, sendmail.mc file. # vi /etc/mail/sendmail.mc Commented out the next line: BEFORE # DAEMON_OPTIONS('Port=smtp, Name=MTA') dnl AFTER # dnl DAEMON_OPTIONS('Port=smtp, Name=MTA') dnl Check that the next lines are correct: # FEATURE(`virtusertable', `hash -o /etc/mail/virtusertable.db')dnl # ... # FEATURE(use_cw_file)dnl # ... # FEATURE(`access_db', `hash -T<TMPF> -o /etc/mail/access.db')dnl Update sendmail.cf # m4 /etc/mail/sendmail.mc > /etc/mail/sendmail.cf Open the port 25 adding the proper line in the iptables file # vi /etc/sysconfig/iptables # -A INPUT -m state --state NEW -m tcp --dport 25 -j ACCEPT restart iptables and sendmail # service iptables restart # service sendmail restart So i thought that would be ok, but when i tried: # mail '[email protected]' # Subject: test subject # test content #. I checked the mail log: # vi /var/log/maillog And that is what I found: Aug 14 17:36:24 dev-admin-test sendmail[20682]: r7D8RItS019578: to=<[email protected]>, ctladdr=<[email protected]> (0/0), delay=1+00:09:06, xdelay=00:00:00, mailer=esmtp, pri=2460500, relay=alt4.gmail- smtp-in.l.google.com., dsn=4.0.0, stat=Deferred: Connection timed out with alt4.gmail-smtp-in.l.google.com. I do not understand why there is a connection time out. Am I missing something? Can anyone help me, please? Thank you.

  Read the article

• Rate limiting bandwidth per IP

  - by Yohan

  First, I am not that good with computer. I even had problem with Windows PC. Right now I own a restaurant which happened to offer free internet. My ISP has my connection setup using a Ubuntu 11.1 box. IP Address is 192.168.1.16 with netmask 255.255.0.0, dns is 192.168.1.1 and gateway is 192.168.1.1. My problem is that my customers complains all day about slow network. When I received that kind of complain, the first thing came to my mind is to scout my area and find out who is the culprit, and ask him not to waste our bandwidth. Now, it is getting bored scouting people around, and I need to implement to my Linux box to limit bandwidth. I don't care if their provider can't be faster, but I want to limit 70kbit for each person. More annoying are people who use flashget and torrents. Usually they consume the biggest bandwidth. My question, how can I limit that? Please guide me in easy way. I've spent few days reading tc documents but doesn't understand a thing. I am using Ubuntu 11.10 Basically, I want all my customer get 70kbps each, no matter what.

  Read the article

• iptables to block VPN-traffic if not through tun0

  - by dacrow

  I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

  Read the article

• Why is writing to my external hard drive slow, while benchmarks show fast writing?

  - by matix2267

  I have an iOmega eGo 320GB portable drive connected through USB2.0 to my laptop running Windows Vista. It's been working fine for quite some time until recently it became very slow when writing e.g. when copying ~300MB movie over to the drive at first it is extremely fast but it actually doesn't write it only puts in cache and then hangs on last 10-20MBs for about a minute. When copying larger files it's the same story: starts fast but then slows down to ~5MB/s (sometimes even slower down to 2MB/s). Strange thing is that I have always had caching disabled for this drive (it was disabled by default and I never bothered changing it). At first I thought that the disk is dying so I checked S.M.A.R.T. values and everything is fine there. I also run chkdsk and it seemed to fix the problem - it worked fast for a few minutes but then it slowed down again. I also tried plugging it into another USB port - no difference. Additionally I noticed that reading under certain circumstances is sometimes slower e.g. loading times for some games are ~10 times longer, whereas simple copying files from this drive to my internal HDD is fast. I ran a speed benchmark using CrystalDiskMark with a 5x100MB run and strangely got these results: read write (MB/s) Seq 33.05 28.25 512k 17.30 15.27 4k 0.267 0.372 4kQD32 0.510 0.260 This is different from what most other people have (I've found many threads about slow disk write while googling but all of them were slow on benchmarks too) which is why I decided to post this problem here. BTW most of the time when writing (or sometimes reading) the activity led is mostly idle (blinks a while and then stops for longer, sometimes has slower blinks ~1 sek, sometimes goes off for a few seconds - extremely long blink :) ) but when benchmarking, defragmenting or just reading (copying from this drive, installing apps from installers there, watching HD videos) it is blinking really fast (like it should) and there are no slowdowns. It shouldn't be driver issue unless stock Windows drivers have some issues I'm not aware of.

  Read the article

• Create image (EBS AMI) takes forever - possibly caused MySQL Server to break?

  - by fuzzybee

  I'm trying to create an EBS AMI from my running EC2 instance to reuse my LAMP fully configured (for my needs). I got my website up and running yesterday on this EC2 instance my MySQL was working fine until this morning (it's not that difficult to install LAMP thanks to yum so I can't see how I could go wrong with this; having said that, it's always difficult for one to realise his own errors) I have seen "Loading, please wait ..." for a few hours now. How do I know whether this is completed or its progress? Shortly after I tried to create the AMI image from my EC2 instance, I encountered database connection error can't connect to local mysql server through socket '/var/lib/mysql/mysql.sock' I was able to restart mysqld at first. But database connection was down again. This time, I could not restart mysqld anymore. It shows MySQL Daemon failed to start. Could my attempt to create the AMI by any chance cause the MySQL server to reboot or corrupt? I did a lot of searched and have done the following although I think I shouldn't have to do any workaround for MySQL server to work here chown -R mysql.mysql /var/lib/mysql/ I also found this workaround but I'm very reluctant to follow due to my belief and the fact I would need to understand this problem first. Any help would be greatly appreciated. Getting back to searching for a solution for the MySQL server problem ... Thanks, Eric

  Read the article

• Http-Only cookies in WebLogic: what versions support them/how and why are they supported?

  - by John

  We want to make all cookies set by our webapp http-only. I only have a basic understanding of the benefits of doing this but I'm told by security people that it's a Good Thing (tm) Our app is running under JDK1.6.05 and WebLogic10.3.0 After way too much digging around Oracle's website for documentation, I've found good evidence that the first version of WebLogic to support http-only cookies is 10.3.1. By "support," I mean the cookie-http-only deployment-descriptor element. Before we go about upgrading, I'd be nice to have these questions answered: 1a) Is it accurate that WL10.3.1 is the first version to support http-only cookies and that we're out of luck with 10.3.0? 1b) If we do indeed need to upgrade, is there an easy to do so under Windows? I've heard people mention an "upgrade jar" that you just stick in the classpath but I can't find any mention of this by Oracle. Does an easy way exist, or do we need to do a full-install of the new version? 2) What does the cookie-http-only deployment-descriptor element do when enabled? Will it ensure all cookies set by the application have an http-only=true attribute? Will it do more or less? Is there anything I'll have to do programmatically? 3) Is there anything in general I should know about http-only cookies, getting my web app to take advantage of them, or other security concerns?

  Read the article

• Arch Linux: eth0 no carrier - network fails at boot

  - by user905686

  The problem My computer is connected to a network where dhcp is required. So my network configuration in /etc/rc.conf looks like interface=eth0 address= netmask= broadcast= gateway= My deamons are DAEMONS=(!hwclock syslog-ng network netfs crond ntpd) With this configuration, Arch hangs at boot a long time at "Network" (Still it says "[done]", but after boot I have no connection). I found out two workaround: Workaround 1 remove network from deamons run mii-tool --reset eth0 and dhcpcd eth0 after boot (somehow it does not work when placing these commands in /etc/rc.local. Then dhcp work very quickly (because of the reset!). Before executing the first command, ip link show eth0 has "NO CARRIER" in output. Afterwards, it doesn´t. (Also, mii-tool first shows "no link", afterwards eth0: 10 Mbit, half duplex, link ok. Workaround 2 Change network configuration to interface=eth0 address=x.y.z.21 netmask=255.255.255.0 broadcast=xxx.y.z.255 gateway=x.y.z.254 whereas x, y, z build the specific adresses of the network (Though dhcp is used, I get a static ip). Add the commands mii-tool --reset eth0 and dhcpcd eth0 to /etc/rc.local Now network starts quickly at boot (though I don´t know if successfully), the commands in /etc/rc.local are executed and the connection is fine after login. What to do? So the problem seems to be that dhcpcd stucks at "wating for carrier" or sth. I do not like the workaround, because some deamons need network (though they seem to start). What can I do to have eth0 ready for dhcp at boot? Or is there another problem?

  Read the article

• Need a place to store a few bytes of meta information on storage media

  - by Jason C

  I'm working on an embedded project. I need a place to store some filesystem-independent meta information on a storage device. The device has an MSDOS partition table. The device also may have unallocated space (depending on its size) but it will be TRIMmed (and also may be blown away by new partitions in the future). I need a location on the device that is not unallocated and that has a low risk of being touched (outside of completely erasing the device). The device is only guaranteed to have an MBR at the point the meta data needs to first be written; meaning there are no EBRs/VBRs present that I could use. There are 446 bytes at the very start of the device available for MBR bootstrap code. Currently my only idea is to store data at the end of this block. However, the device is bootable and I have no way of knowing if I'd be blowing away bootstrap code or not. The sector size is 512 bytes and the MBR is the first sector, I'm pretty sure (correct me if I'm wrong) that that means the second sector is available for use by partition data, so I can't use that either. Does anybody have any ideas? I need 4 bytes of space.

  Read the article

• S.M.A.R.T. broken sectors

  - by Jeffrey Vandenborne

  Recently I received my hard drive (LaCie) that I've sent away for warranty, my disk failed, and I used Palimpsest Disk utility to check if anything was wrong in the S.M.A.R.T Status. And it said that there were a few broken sectors. So the next day, I went to the store and told the story. 4 weeks later I actually got my drive back. The first thing I did was plugging it in and starting the disk utility, and weirdly it showed me pretty much the exact same things, even the values of most tests were the same as they were before when my drive broke. The serial number is different though, but it does show a very peculiar value. Now I'm wondering, I'm almost sure it's the exact same drive and it still says I've got broken sectors, does it just say that because it has been cached in the drive somewhere while LaCie DID actually fix it? Or should I run the extended self test (which seems to take hours) first? Also I've tried the smartctl command tool, it says the drive has smart support, but it doesn't show anything, it says that it's enabled, but then it says that it's disabled, picture below The picture of the Disk utility: Thanks in advance

  Read the article

• Strange sound behavior

  - by caarlos0

  First of all, sorry for the tittle. English isn't my native language, and I can't find a word to describe the strange behavior I'm getting here. In the most simple explanation, is like sound keeps going down and up again... Think in a kid with that old radios that have a circled volume button. Think like these kid keeps "turning" the volume button. That is the behavior I'm getting here. At first, I believed that it was a pulseaudio issue, but, it isn't. I followed the wiki part I think that should be my problem, but it didn't work. After that, as I'm using XFCE, I didn't really need pulseaudio, so I removed it and stays with a clean alsa, hopping that will fix my problem. Sweet mistake. It really looks like a kid looking for trouble. I believed it worked, and, suddenly, here is the same issue again. BTW: I have a full-upgraded testing system (yeah, I upgraded to testing hopping for new pulseaudio version which fix the issue), no pulseaudio at all, just xfce, started with startxfce. What can I do to fix this? It's extremely annoying... sometimes I just want to throw my laptop in the wall because of this. Any extra info you need, please, tell me. Thanks in advance -- EDIT: My alsamixer is like this: And here is a video with the sound behavior.

  Read the article

< Previous Page | 356 357 358 359 360 361 362 363 364 365 366 367  | Next Page >