Search Results

Search found 19265 results on 771 pages for 'country specific'.

Page 361/771 | < Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >

• broadcom 5722 NIC not installed on Ubuntu Server, although driver present

  - by Bastien

  Hello, I just installed Ubuntu Server 10.04 LTS, running kernel 2.6.32-24-server, on a brand new Dell T110 server, supposedly fully compatible with Ubuntu Server. I have two NICs: one ONBOARD, the other additional on PCI. both of them are Broadcom netXtreme 5572. on the first boot of the system, I could see both cards as eth0 and eth1 (with ifconfig) I configured eth0 as static IP (as planned), and did not configure eth1. after rebooting, one of the two NICs "disappeared": it does not appear in ifconfig at all. the one that disappeared is the ONBOARD one. I investigated a bit and found the following things: the card is SEEN, but not "installed", it appears as "UNCLAIMED" in lshw: *-network UNCLAIMED description: Ethernet controller product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress cap_list configuration: latency=0 resources: memory:df9f0000-df9fffff *-network description: Ethernet interface product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 00 serial: 00:10:18:60:23:64 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.102 duplex=full firmware=5722-v3.09 ip=10.129.167.25 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:35 memory:dfaf0000-dfafffff so I checked my dmesg and found a few strange lines, showing, there actually is a problem bringing up this card: [ 3.737506] tg3: Could not obtain valid ethernet address, aborting. [ 3.737527] tg3 0000:04:00.0: PCI INT A disabled [ 3.737535] tg3: probe of 0000:04:00.0 failed with error -22 [ 3.737553] alloc irq_desc for 17 on node -1 [ 3.737555] alloc kstat_irqs on node -1 [ 3.737560] tg3 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.737566] tg3 0000:05:00.0: setting latency timer to 64 [ 3.793529] eth0: Tigon3 [partno(BCM95722A2202G) rev a200] (PCI Express) MAC address 00:10:18:60:23:64 [ 3.793532] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 3.793534] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.793536] eth0: dma_rwctrl[76180000] dma_mask[64-bit] that actually shows that one NIC is recognized, the other is not. I researched a bit more, with lspci -v: 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: fast devsel, IRQ 16 Memory at df9f0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-00-00-fe-ff-00-00-00 Kernel modules: tg3 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: bus master, fast devsel, latency 0, IRQ 35 Memory at dfaf0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 64-23-60-fe-ff-18-10-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 here I could see that the MAC address is 00-00-00-FE-FF-00-00-00, which, according to some forum posts on several websites, could be an issue. I've researched everything I could on the net, and found out several people having slightly comparable issues, but they usually involve different HW, and do not provide a proper explanation / solution... I would appreciate if anyone around here has some info to share ! thanks

  Read the article

• ERROR 2003 (HY000): Can't connect to MySQL server on (111)

  - by JohnMerlino

  I am unable to connect to on my ubuntu installation a remote tcp/ip which contains a mysql installation: viggy@ubuntu:~$ mysql -u user.name -p -h xxx.xxx.xxx.xxx -P 3306 Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on 'xxx.xxx.xxx.xxx' (111) I commented out the line below using vim in /etc/mysql/my.cnf: # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 Then I restarted the server: sudo service mysql restart But still I get the same error. This is the content of my.cnf: # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp lc-messages-dir = /usr/share/mysql skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 16M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog due to /etc/mysql/conf.d/mysqld_safe_syslog.cnf. # # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ (Note that I can log into my local mysql install just fine by running mysql (and it will log me in as root) and also note that I can get into mysql in the remote server by logging into via ssh and then invoking mysql), but I am unable to connect to the remote server via my terminal using the host, and I need to do it that way so that I can then use mysql workbench.

  Read the article

• How do I get my ubuntu server to listen for database connections?

  - by Bob Flemming

  I am having a problems connecting to my database outside of phpmyadmin. Im pretty sure this is because my server isn't listening on port 3306. When I type: sudo netstat -ntlp on my OTHER working server I can see the following line: tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 20445/mysqld However, this line does not appear on the server I am having difficulty with. How do I make my sever listen for mysql connections? Here my my.conf file: # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp lc-messages-dir = /usr/share/mysql #skip-networking=off #skip_networking=off #skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 0.0.0.0 # # * Fine Tuning # key_buffer = 64M max_allowed_packet = 64M thread_stack = 650K thread_cache_size = 32 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 2M query_cache_size = 32M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog due to /etc/mysql/conf.d/mysqld_safe_syslog.cnf. # # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 32M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 32M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/

  Read the article

• Why do we need different CPU architecture for server & mini/mainframe & mixed-core?

  - by claws

  Hello, I was just wondering what other CPU architectures are available other than INTEL & AMD. So, found List of CPU architectures on Wikipedia. It categorizes notable CPU architectures into following categories. Embedded CPU architectures Microcomputer CPU architectures Workstation/Server CPU architectures Mini/Mainframe CPU architectures Mixed core CPU architectures I was analyzing the purposes and have few doubts. I taking Microcomputer CPU (PC) architecture as reference and comparing others. Embedded CPU architecture: They are a completely new world. Embedded systems are small & do very specific task mostly real time & low power consuming so we do not need so many & such wide registers available in a microcomputer CPU (typical PC). In other words we do need a new small & tiny architecture. Hence new architecture & new instruction RISC. The above point also clarifies why do we need a separate operating system (RTOS). Workstation/Server CPU architectures I don't know what is a workstation. Someone clarify regarding the workstation. As of the server. It is dedicated to run a specific software (server software like httpd, mysql etc.). Even if other processes run we need to give server process priority therefore there is a need for new scheduling scheme and thus we need operating system different than general purpose one. If you have any more points for the need of server OS please mention. But I don't get why do we need a new CPU Architecture. Why cant Microcomputer CPU architecture do the job. Can someone please clarify? Mini/Mainframe CPU architectures Again I don't know what are these & what miniframes or mainframes used for? I just know they are very big and occupy complete floor. But I never read about some real world problems they are trying to solve. If any one working on one of these. Share your knowledge. Can some one clarify its purpose & why is it that microcomputer CPU archicture not suitable for it? Is there a new kind of operating system for this too? Why? Mixed core CPU architectures Never heard of these. If possible please keep your answer in this format: XYZ CPU architectures Purpose of XYZ Need for a new architecture. why can't current microcomputer CPU architecture work? They go upto 3GHZ & have upto 8 cores. Need for a new Operating System Why do we need a new kind of operating system for this kind of archictures?

  Read the article

• PXE Boot not working

  - by Nishant

  Please explain the error in this screenshot DHCP Setting: This screenshot was taken after powering off the old comp hence he server interface is shown as the wireless card - it becomes 192.168.0.1 when I connect wires and power up the old laptop to boot via PXE. My scenario is simple. An old laptop and a new laptop . A cross over cable ( that I myself made from CAT 6 cable by cutting it and connecting 4 wires as mentioned in some doc). The new laptop ( tftp server ) has a Wirelss Card ( with which I am browsing and writing this ) . And the cable is connected between laptops . TFTP server ( new laptop details ) Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::f511:3d4a:ca01:122e%16 IPv4 Address. . . . . . . . . . . : 192.168.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.2 Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Achilles Link-local IPv6 Address . . . . . : fe80::99b1:8ae0:9e6c:f300%11 IPv4 Address. . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.1

  Read the article

• openvpn not creating internal route for client

  - by user42055

  I have two openvpn clients and a server using shared keys. I have internal routes specified in the ccd directory for both clients, but when they connect, the server only creates the internal route for one of them, despite the logs saying it's creating both. Both clients and the server use the "--script-security 2" command-line option. Can anyone think of why it would do this ? My ccd files are: client1: iroute 192.168.0.0 255.255.255.0 client2: iroute 10.0.1.0 255.255.255.0 My log file shows the following (cropped): May 3 17:22:59 kino openvpn[2416]: 118.208.58.60:48730 [client1] Peer Connection Initiated with 118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 OPTIONS IMPORT: reading client specific options from: ccd/client1 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: Learn: 192.168.150.10 -> client1/118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: primary virtual IP for client1/118.208.58.60:48730: 192.168.150.10 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: internal route 192.168.0.0/24 -> client1/118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: Learn: 192.168.0.0/24 -> client1/118.208.58.60:48730 May 3 17:23:01 kino openvpn[2416]: client1/118.208.58.60:48730 PUSH: Received control message: 'PUSH_REQUEST' May 3 17:23:01 kino openvpn[2416]: client1/118.208.58.60:48730 SENT CONTROL [client1]: 'PUSH_REPLY,route 192.168.150.1,topology net30,ping 10,ping-restart 120,ifconfig 192.168.150.10 192.168.150.9' (status=1) May 3 17:21:36 kino openvpn[2416]: 124.148.1.90:59277 [client2] Peer Connection Initiated with 124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 OPTIONS IMPORT: reading client specific options from: ccd/client2 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: Learn: 192.168.150.14 -> client2/124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: primary virtual IP for client2/124.148.1.90:59277: 192.168.150.14 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: internal route 10.0.1.0/24 -> client2/124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: Learn: 10.0.1.0/24 -> client2/124.148.1.90:59277 May 3 17:21:39 kino openvpn[2416]: client2/124.148.1.90:59277 PUSH: Received control message: 'PUSH_REQUEST' May 3 17:21:39 kino openvpn[2416]: client2/124.148.1.90:59277 SENT CONTROL [client2]: 'PUSH_REPLY,route 192.168.150.1,topology net30,ping 10,ping-restart 120,ifconfig 192.168.150.14 192.168.150.13' (status=1) And after both clients have connected, the routing table looks like this: 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 203.209.167.192 0.0.0.0 255.255.255.224 U 0 0 0 eth0 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 203.209.167.193 0.0.0.0 UG 0 0 0 eth0 As you can see, it's created the route to 192.168.0.0/24 (client1) but not to 10.0.1.0/24 (client2), even though the log says it's been created. Any suggestions why ?

  Read the article

• How to find my VPN client IP in windows

  - by cateof

  When I run ipconfig and I get the following: C:\Documents and Settings\grmsrh14>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 112.25.2.222 Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : 112.25.2.1 DHCP Class ID . . . . . . . . . . : rise Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected PPP adapter my_lab: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.2.251.41 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : Is there a command that prints only the my_lab(VPN) IP address, ie 10.2.251.41?

  Read the article

• File copying utility like rsync with error handling like ddrescue, for data recovery from a hard drive with bad sectors or hardware failure

  - by purefusion

  I have a hard drive with either bad blocks or sectors that are failing to read due to potential mechanical issues, such as a bad disk head, bad motor, or some other issue that is causing the hard drive to read data excruciatingly slowly and with lots of read errors. I'm seeing an average of 50 KB/sec, with some reads dropping below 10 KB/sec, and frequently it gets stuck on a file or sector altogether, usually for quite a long time—from 2-10 minutes or more (when using rsync, before it times out). Speed seems to vary wildly, and it gets stuck on files a lot, and when it finally gets "unstuck" it only seems to last for a short burst before it gets stuck again. The drive is also very quiet with only an occasional sound of files copying (usually when it gets stuck/unstuck for a brief time, before getting stuck again). Thus, there are none of those evil sounds that are normally associated with HDD death. Someone suggested that the problems sounded like they might be caused by a misaligned disk head, which requires a lot of re-reads before it finally reads data with success. Sounds plausible, but I digress... Anyway, the problem with rsync is that it seems to have no decent error handling support. Obviously, it wasn't meant for use in recovering data from failing hard drives, but all the so-called "data recovery" utilities out there that are meant for such use usually focus on recovery of deleted files or messed up partitions, rather than copying files off dying hard drives. Deleted file recovery is not what I need, obviously, so perhaps you can understand my disappointment in not being able to find what I'm after yet. Naturally, this is where you'd probably say "You should use ddrescue!" Well, that's all fine and dandy, but I've already got most of the data backed up, so I just want to recover certain files. I'm not concerned with trying to recover a full partition block-by-block as ddrescue does. I am only interested in rescuing just specific files and directories. Ideally, what I'd like is some sort of cross between rsync and ddrescue: something that lets me specify source and destination as directories of normal files like rsync (rather than two full partitions as ddrescue requires), with a way to skip files with errors in an initial run, and then allows me to attempt recovery of those files with errors in a later run (with a slightly altered command, of course), perhaps even offering an option to specify the number of retry attempts ...just like how ddrescue works with blocks, only I want a utility that works with specific files/directories like rsync does. So am I daydreaming here, or does something out there exist that can do this? Or, maybe even a way to make rsync or ddrescue work in such a way? I'm really open to whatever solutions might work, so long as they let me choose which files I want to "rescue", and can skip files with errors in the initial run, and try/retry those errors again later. So far I've tried rsync with the following options, but it often gets stuck on a file for longer than the timeout, and ideally I'd just like it to move on to the next file and come back later to the files it gets stuck on. I don't think that's possible though. Anyway, here's what I've been using up till now: rsync -avP --stats --block-size=512 --timeout=600 /path/to/source/* /path/to/destination/

  Read the article

• Bridging a non-persistent PPP connection to wireless (or wired) in Windows XP

  - by phooze

  I have a 3G modem-like device (eMobile's D01NX, PC card style, for any Japan nerds out there) that I use to connect my PC to the Internet. I'd like to bridge this connection with another computer either via an ad-hoc wireless network, or a simple cross-over cable (either are options). However, when I open "Network Connections", I do not see the PPP connection (otherwise I could click both and bridge). I believe this is because there is software (provided by the vendor) that is handling the card directly and registering a PPP connection dynamically. When connected, an ipconfig at the command line yields: Ethernet adapter wireless: Connection-specific DNS Suffix . : Autoconfiguration IP Address. . . : 169.254.5.169 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Ethernet adapter lan: Media State . . . . . . . . . . . : Media disconnected PPP adapter {B59EEDDE-A22B-48DF-93E5-04842B641257}: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 114.xx.xxx.xx Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 114.xx.xxx.xx (I've commented out my IP address for privacy reasons, but what does appear there is a functional Internet IP address.) When I disconnect the adapter with the vendor software, the PPP connection disappears completely from the ipconfig list. Any ideas on how to do this?

  Read the article

• How to use a different Ethernet connection

  - by SteveC

  I'm running a virtual machine at home which has a VPN connection to our main office, but I also want to connect to a share on another machine at home. When I check with IPCONFIG I can see two ethernet connections ... my work VPN ... Ethernet adapter Local Area Connection* 11: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : xxxx::xxxx:xxxx:xxxx:xxxxxxx IPv4 Address. . . . . . . . . . . : XXX.XXX.XXX.XXX Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : XXX.XXX.XXX.XXX and home local ... Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : lan Link-local IPv6 Address . . . . . : xxxx::xxxx:xxxx:xxxx:xxxxxxx IPv4 Address. . . . . . . . . . . : 192.168.1.70 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : What's weird is when I've been working before with a plugged-in ethernet cable I've not had any problem getting to the share? I can PING the other machine, but I can't access the share at ... \\othermachine\c$ I tried 'TRACERT` but that disappears off to the work network and eventually gets back to the local other machine after a few time-outs Is there anyway to "force" the connection to stay local ? UPDATE: the VPN is AEP SSL Tunnel

  Read the article

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• "The server closed the connection without sending any data"

  - by Toby

  Server setup The problem Diagnostic information What I've tried Specific Help needed 1. I have the following server setup: Debian Squeeze Linux 2.6.32-5-amd64 Apache2-mpm-prefork 2.2.16-6+squeeze10 PHP 5.3.3-7+squeeze14 This server is protected with the Suhosin Patch 0.9.9.1 Max Requests Per Child: 0 - Keep Alive: on - Max Per Connection: 100 Timeouts Connection: 300 - Keep-Alive: 15 Loaded Modules core mod_log_config mod_logio prefork http_core mod_so mod_alias mod_auth_basic mod_auth_digest mod_authn_file mod_authz_default mod_authz_groupfile mod_authz_host mod_authz_user mod_cgi mod_deflate mod_dir mod_env mod_mime mod_negotiation mod_php5 mod_reqtimeout mod_rewrite mod_setenvif mod_ssl mod_status Wordpress 3.4.2 (Upgrading to 3.5 soon :) 2. The problem When I restart the server (sudo shutdown -r now), going to any website page results in the following error from the web browser (in this case, Google Chrome, but other browsers also show the same error). This error can also occur an hour or so after all is working ok, seemingly randomly, which is my biggest concern as it means my server is not reliable: No data received Unable to load the web page because the server sent no data. Here are some suggestions: Reload this web page later. Error 324 (net::ERR_EMPTY_RESPONSE): The server closed the connection without sending any data. 3. Diagnostic information The apache error log contains the folowing entries: [Fri Dec 14 22:23:27 2012] [notice] child pid 1955 exit signal Floating point exception (8) [Fri Dec 14 22:23:27 2012] [notice] child pid 1956 exit signal Floating point exception (8) [Fri Dec 14 22:23:29 2012] [notice] child pid 1957 exit signal Floating point exception (8) [Fri Dec 14 22:23:30 2012] [notice] child pid 1958 exit signal Floating point exception (8) [Fri Dec 14 22:23:32 2012] [notice] child pid 1959 exit signal Floating point exception (8) [Fri Dec 14 22:23:32 2012] [notice] child pid 1960 exit signal Floating point exception (8) [Fri Dec 14 22:23:34 2012] [notice] child pid 1961 exit signal Floating point exception (8) [Fri Dec 14 22:23:34 2012] [notice] child pid 1962 exit signal Floating point exception (8) 4. What I've tried a) I can 'fix' the website temporarily by resetting the server twice (resetting it once does not work) using the following commands. NB: the 'reload' option does not work, I have to use restart twice. However, the error can reoccur sometime later. sudo /etc/init.d/apache2 restart sudo /etc/init.d/apache2 restart b) I have tried disabling suhosin by uninstalling php5-suhosin, but a php info page still shows "This server is protected with the Suhosin Patch 0.9.9.1". I have tried putting Suhosin into simulation mode by creating a file /etc/php5/apache2/conf.d/suhosin.ini containing: [suhosin] suhosin.simulation = On The php info page shows the suhosin.ini file in the list of "Additional .ini files parsed" but the php info page still shows "This server is protected with the Suhosin Patch 0.9.9.1" c) Increasing the PHP memory limit In /etc/php5/apache2/ : ; Maximum amount of memory a script may consume (128MB) ; http://php.net/memory-limit memory_limit = 512M d) Disabling all Wordpress plugins, and going back to the default theme. 5. Specific help needed I would very much like help in debugging what is going on here. I am not sure how to determine what processes are in the Apache error log which are exiting "[notice] child pid 1955 exit signal Floating point exception (8)", or what is causing them to exit. And whether suhosin is part of the problem (and how to disable it if it is). Thank you in advance for any advice or tips you can offer in helping me debug this.

  Read the article

• Set source address to use tun device does not work (Debian Squeeze)

  - by A. Donda

  there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

  Read the article

• connecting mysql from android with jdbc

  - by manuraphy

  hai i used the following code to connect mysql in local host from android. it only displays the actions given in catch section . i dont know whether its a connection problem or not package com.test1; import java.sql.Connection; import java.sql.DriverManager; import java.sql.PreparedStatement; import java.sql.ResultSet; import android.app.Activity; import android.os.Bundle; import android.widget.TextView; public class Test1Activity extends Activity { /** Called when the activity is first created. */ String str="new"; static ResultSet rs; static PreparedStatement st; static Connection con; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); final TextView tv=(TextView)findViewById(R.id.user); try { Class.forName("com.mysql.jdbc.Driver"); con=DriverManager.getConnection("jdbc:mysql://10.0.2.2:8080/example","root",""); st=con.prepareStatement("select * from country where id=1"); rs=st.executeQuery(); while(rs.next()) { str=rs.getString(2); } tv.setText(str); setContentView(tv); } catch(Exception e) { tv.setText(str); } } } when executes it displays "new" in the avd. java.lang.management.ManagementFactory.getThreadMXBean, referenced from method com.mysql.jdbc.MysqlIO.appendDeadlockStatusInformation Could not find class 'javax.naming.StringRefAddr', referenced from method com.mysql.jdbc.ConnectionPropertiesImpl$ConnectionProperty.storeTo Could not find method javax.naming.Reference.get, referenced from method com.mysql.jdbc.ConnectionPropertiesImpl$ConnectionProperty.initializeFrom can anyone suggest some solution ? and thankz in advance

  Read the article

• iPhone: Software Development And Distribution

  - by xsl

  I have a few quick questions about the iPhone software development. I did some research about the topic, but there are a few specific things I would like to ask here, because I will have to estimate the cost of the required hardware and software, before I am allowed to buy anything. I never did any Mac development nor have I ever owned an iPhone, so needless to say this is quite hard for me. I will buy an iMac mini with 2 GB RAM for iPhone development. I will have to use it at the same time as my regular PC, but the majority of the time I won't use the Mac at all. Do I have to buy an additional monitor, a mouse and a keyboard or is there a better solution? I will have to port a C library to the iPhone platform and develop an iPhone application that uses the ported library. Do I need anything else than the iPhone SDK to do this? If I use an external library (see above), can I test the application with the integrated emulator, or is it recommend to buy the device? In a later phase of the project I will have to buy an iPhone, but I will have to wait until the iPhone 4 is released here in Europe, because the application requires a camera. In addition to this I will have to send data to a remote webservice. Aside from these two things I don't require any other features. Can I just buy the iPhone online from another country (the iPhones here are sim locked), or should I buy one with a contract? When the application is ready, it will be installed on a few iPhones owned by our customer. Because of security reasons it is crucial that there is no third party involved in this process (i.e. the application should not be distributed on the app store). Is this possible?

  Read the article

• Problem with Informix JDBC, MONEY and decimal separator in string literals

  - by Michal Niklas

  I have problem with JDBC application that uses MONEY data type. When I insert into MONEY column: insert into _money_test (amt) values ('123.45') I got exception: Character to numeric conversion error The same SQL works from native Windows application using ODBC driver. I live in Poland and have Polish locale and in my country comma separates decimal part of number, so I tried: insert into _money_test (amt) values ('123,45') And it worked. I checked that in PreparedStatement I must use dot separator: 123.45. And of course I can use: insert into _money_test (amt) values (123.45) But some code is "general", it imports data from csv file and it was safe to put number into string literal. How to force JDBC to use DBMONEY (or simply dot) in literals? My workstation is WinXP. I have ODBC and JDBC Informix client in version 3.50 TC5/JC5. I have set DBMONEY to just dot: DBMONEY=. EDIT: Test code in Jython: import sys import traceback from java.sql import DriverManager from java.lang import Class Class.forName("com.informix.jdbc.IfxDriver") QUERY = "insert into _money_test (amt) values ('123.45')" def test_money(driver, db_url, usr, passwd): try: print("\n\n%s\n--------------" % (driver)) db = DriverManager.getConnection(db_url, usr, passwd) c = db.createStatement() c.execute("delete from _money_test") c.execute(QUERY) rs = c.executeQuery("select amt from _money_test") while (rs.next()): print('[%s]' % (rs.getString(1))) rs.close() c.close() db.close() except: print("there were errors!") s = traceback.format_exc() sys.stderr.write("%s\n" % (s)) print(QUERY) test_money("com.informix.jdbc.IfxDriver", 'jdbc:informix-sqli://169.0.1.225:9088/test:informixserver=ol_225;DB_LOCALE=pl_PL.CP1250;CLIENT_LOCALE=pl_PL.CP1250;charSet=CP1250', 'informix', 'passwd') test_money("sun.jdbc.odbc.JdbcOdbcDriver", 'jdbc:odbc:test', 'informix', 'passwd') Results when I run money literal with dot and comma: C:\db_examples>jython ifx_jdbc_money.py insert into _money_test (amt) values ('123,45') com.informix.jdbc.IfxDriver -------------- [123.45] sun.jdbc.odbc.JdbcOdbcDriver -------------- there were errors! Traceback (most recent call last): File "ifx_jdbc_money.py", line 16, in test_money c.execute(QUERY) SQLException: java.sql.SQLException: [Informix][Informix ODBC Driver][Informix]Character to numeric conversion error C:\db_examples>jython ifx_jdbc_money.py insert into _money_test (amt) values ('123.45') com.informix.jdbc.IfxDriver -------------- there were errors! Traceback (most recent call last): File "ifx_jdbc_money.py", line 16, in test_money c.execute(QUERY) SQLException: java.sql.SQLException: Character to numeric conversion error sun.jdbc.odbc.JdbcOdbcDriver -------------- [123.45]

  Read the article

• Nokogiri pull parser (Nokogiri::XML::Reader) issue with self closing tag

  - by Vlad Zloteanu

  I have a huge XML(400MB) containing products. Using a DOM parser is therefore excluded, so i tried to parse and process it using a pull parser. Below is a snippet from the each_product(&block) method where i iterate over the product list. Basically, using a stack, i transform each <product> ... </product> node into a hash and process it. while (reader.read) case reader.node_type #start element when Nokogiri::XML::Node::ELEMENT_NODE elem_name = reader.name.to_s stack.push([elem_name, {}]) #text element when Nokogiri::XML::Node::TEXT_NODE, Nokogiri::XML::Node::CDATA_SECTION_NODE stack.last[1] = reader.value #end element when Nokogiri::XML::Node::ELEMENT_DECL return if stack.empty? elem = stack.pop parent = stack.last if parent.nil? yield(elem[1]) elem = nil next end key = elem[0] parent_childs = parent[1] # ... parent_childs[key] = elem[1] end The issue is on self-closing tags (EG <country/>), as i can not make the difference between a 'normal' and a 'self-closing' tag. They both are of type Nokogiri::XML::Node::ELEMENT_NODE and i am not able to find any other discriminator in the documentation. Any ideas on how to solve this issue?

  Read the article

• Open layers multiple mouseover events for multiple markers

  - by Bren G.

  I have the following loop inside an function init(); which is executed "onload", I am having traouble attaching the mouseover event for each marker, the alert i always returns the value of the last loop/iteration? for(i=0; i<document.getElementById('departureSelect').options.length; i++){ var coords = eval(document.getElementById('departureSelect').options[i].value); if(i==0){ window['popup'+i] = new OpenLayers.Marker(new OpenLayers.LonLat(coords[0], coords[1]),icon); }else{ window['popup'+i] = new OpenLayers.Marker(new OpenLayers.LonLat(coords[0], coords[1]),icon.clone()); } window['z'+i] = new OpenLayers.Popup.Anchored(coords[2], new OpenLayers.LonLat(coords[0], coords[1]), new OpenLayers.Size(0,0), '<span class="country-label">' + coords[2] + '</span>', icon, false ); window['z'+i].autoSize = true; window['z'+i].setBorder('1px solid #888'); map.addPopup(window['z'+i]); window['z'+i].hide(); window['popup'+i].events.register('mouseover', window['popup'+i], function(e){ alert(i); // only returns loast iteration of i????? }); countries.addMarker(window['popup'+i]); }

  Read the article

• Sphinx PHP Geodist problems

  - by James

  Below is my PHP function to call nearby points using Sphinx for MySQL. There are hundreds of thousands of nearby points which to what I can tell, are being indexed by Sphinx, but simply fails silently when searching with Sphinx. Other Sphinx queries I run against other indexes work completely fine. function nearby($latitude, $longitude, $radius) { global $sphinx; $sphinx->SetMatchMode(SPH_MATCH_ALL); $sphinx->SetArrayResult(true); $sphinx->SetLimits(0, 1000); $sphinx->SetGeoAnchor('latitude', 'longitude', (float) deg2rad($latitude), (float) deg2rad($longitude)); $circle = (float) $radius * 1.609344; $sphinx->SetFilterFloatRange('@geodist', 0.0, $circle); $matches = $sphinx->Query('', 'geo'); return $matches; } $nearby = nearby($latitude, $longitude, 10000); var_dump($nearby); This, when called with valid latitude and longitude co-ords and a very large radius for debugging produces: bool(false) Below is my sphinx.conf covering the geo part: source geo { type = mysql sql_host = 127.0.0.1 sql_user = user sql_pass = pass sql_db = db sql_port = 3306 sql_query_pre = set names utf8 sql_query_pre = set session query_cache_type=OFF sql_query = SELECT id,city,region,country,radians(longitude) AS longitude, radians(latitude) AS latitude FROM points; sql_attr_float = longitude sql_attr_float = latitude sql_ranged_throttle = 0 sql_query_info = SELECT * FROM points WHERE id = $id } index geo { source = geo path = /var/data/geo docinfo = extern #mlock = 0 #morphology = none min_word_len = 1 charset_type = utf-8 #charset_table = 0..9, A..Z->a..z, _, a..z, U+410..U+42F->U+430..U+44F, U+430..U+44F ignore_chars = U+00AD html_strip = 0 enable_star = 0 } indexer { mem_limit = 1024M } searchd { port = 3312 log = /var/log/searchd.log query_log = /var/log/query.log read_timeout = 5 max_children = 5 pid_file = /var/log/searchd.pid max_matches = 10000 seamless_rotate = 1 preopen_indexes = 0 unlink_old = 1 }

  Read the article

• How do I use XML prefixes in C#?

  - by Andrew Mock

  EDIT: I have now published my app: http://pastebin.com/PYAxaTHU I was trying to make console-based application that returns my temperature. using System; using System.Xml; namespace GetTemp { class Program { static void Main(string[] args) { XmlDocument doc = new XmlDocument(); doc.LoadXml(downloadWebPage( "http://www.andrewmock.com/uploads/example.xml" )); XmlNamespaceManager man = new XmlNamespaceManager(doc.NameTable); man.AddNamespace("aws", "www.aws.com/aws"); XmlNode weather = doc.SelectSingleNode("aws:weather", man); Console.WriteLine(weather.InnerText); Console.ReadKey(false); } } } Here is the sample XML: <aws:weather xmlns:aws="http://www.aws.com/aws"> <aws:api version="2.0"/> <aws:WebURL>http://weather.weatherbug.com/WA/Kenmore-weather.html?ZCode=Z5546&Units=0&stat=BOTHL</aws:WebURL> <aws:InputLocationURL>http://weather.weatherbug.com/WA/Kenmore-weather.html?ZCode=Z5546&Units=0</aws:InputLocationURL> <aws:station requestedID="BOTHL" id="BOTHL" name="Moorlands ES" city="Kenmore" state=" WA" zipcode="98028" country="USA" latitude="47.7383346557617" longitude="-122.230278015137"/> <aws:current-condition icon="http://deskwx.weatherbug.com/images/Forecast/icons/cond024.gif">Mostly Cloudy</aws:current-condition> <aws:temp units="&deg;F">40.2</aws:temp> <aws:rain-today units=""">0</aws:rain-today> <aws:wind-speed units="mph">0</aws:wind-speed> <aws:wind-direction>WNW</aws:wind-direction> <aws:gust-speed units="mph">5</aws:gust-speed> <aws:gust-direction>NW</aws:gust-direction> </aws:weather> I'm just not sure how to use XML prefixes correctly here. What is wrong with this?

  Read the article

• Entity Data Model & DataGridView - Creating new objects

  - by AcousticBoom

  I'm pretty new to the EDM, so bear with me. I have a windows form that has a DataGridView on it that's bound from the EDM I created. I figured out how to update my changes fine, but it's when the user creates a new row that I'm having a problem. I tried numerous ways and many google searches, but came up with nothing so far. Here's how the data is loaded: Dim boilerID As Integer = DirectCast(ddlBoiler.SelectedValue, Integer) Dim countryID As Integer = DirectCast(ddlCountry.SelectedValue, Integer) Dim ratings = From r In _Context.Rating _ Where r.Boiler.Boiler_ID = boilerID _ And r.Country.Country_ID = countryID _ Order By r.Sequence _ Select r RatingBindingSource.DataSource = ratings.ToList() Also, all I'm doing to save the information right now is the following: Private Sub btnSave_Click(ByVal sender As Object, ByVal e As System.EventArgs) Handles btnSave.Click _Context.SaveChanges() End Sub I want the user to be able to use the grid's "new row" feature to add new items to the database instead of having to click a button and open a new dialog. How would this be accomplished? I can include some of the methods i tried for adding new items if anyone needs to see. Thanks!

  Read the article

• jstl taglib not found, where have I gone wrong?

  - by James.Elsey

  I'm trying to add Google Maps onto my JSPs by using the googlemaps jstl taglib. I've added this into my maven pom <dependency> <groupId>com.lamatek</groupId> <artifactId>googlemaps</artifactId> <version>0.98c</version> <scope>provided<>/scope </dependency> This then included the googlemaps-0.98c library under my project libraries in NetBeans, I right clicked and selected Manually install artifact and located the googlemaps.jar file I had downloaded. I've then added this into my taglibs file <%@taglib prefix="googlemaps" uri="/WEB-INF/googlemaps" %> And have then included this where I actually want to show a map on my jsp <googlemaps:map id="map" width="250" height="300" version="2" type="STREET" zoom="12"> <googlemaps:key domain="localhost" key="xxxx"/> <googlemaps:point id="point1" address="74 Connors Lane" city="Elkton" state="MD" zipcode="21921" country="US"/> <googlemaps:marker id="marker1" point="point1"/> </googlemaps:map> But when I load up my application, I get the following error. org.apache.jasper.JasperException: /jsp/dashboard.jsp(1,1) /jsp/common/taglibs.jsp(6,56) PWC6117: File "/WEB-INF/googlemaps" not found root cause org.apache.jasper.JasperException: /jsp/common/taglibs.jsp(6,56) PWC6117: File "/WEB-INF/googlemaps" not found Have I missed something simple? I'm unable to spot what I've done wrong so far.. Thanks

  Read the article

• How to ajax load a parent-child listbox in JQuery/Asp.net MVC popup?

  - by melaos

  hi guys, i'm new to the asp.net mvc. and i have a link which will popup show a 3 panes listbox which allows the user to select country, region and language. and when the user click on the language, this will redirect back to the controller and refresh the page and show the proper localized content. i was thinking of using a jquery dialog/modal to do this but so i try using fancybox for this which will load the hidden div of the three listbox up. unfortunately, on clicking on the first listbox, the page will call a jquery event which will show the populate the 2nd list box in which the lightbox will close. is there a better way to do this? or i'm not using the proper jquery plugin? i was thinking of putting the whole three panes inside a html file and do ajax call to get the content into that page and load the listbox like that and just use the html popup like a normal popup. Any suggestions? i'm stuck, help!!

  Read the article

• ASP.NET Setting Culture with InitializeCulture

  - by Helen

  I have a website with three domains .com, .de and .it Each domain needs to default to the local language/culture of the country. I have created a base page and added an InitializeCulture Protected Overrides Sub InitializeCulture() Dim url As System.Uri = Request.Url Dim hostname As String = url.Host.ToString() Dim SelectedLanguage As String If HttpContext.Current.Profile("PreferredCulture").ToString Is Nothing Then Select Case hostname Case "www.domain.de" SelectedLanguage = "de" Thread.CurrentThread.CurrentUICulture = New CultureInfo(SelectedLanguage) Thread.CurrentThread.CurrentCulture = CultureInfo.CreateSpecificCulture(SelectedLanguage) Case "www.domain.it" SelectedLanguage = "it" Thread.CurrentThread.CurrentUICulture = New CultureInfo(SelectedLanguage) Thread.CurrentThread.CurrentCulture = CultureInfo.CreateSpecificCulture(SelectedLanguage) Case Else SelectedLanguage = "en" Thread.CurrentThread.CurrentUICulture = New CultureInfo(SelectedLanguage) Thread.CurrentThread.CurrentCulture = CultureInfo.CreateSpecificCulture(SelectedLanguage) End Select End If End Sub This is fine. The problem now occurs because we also want three language selection buttons on the home page so that the user can override the domain language. So on my Default.asp.vb we have three button events like this... Protected Sub langEnglish_Click(ByVal sender As Object, ByVal e As System.Web.UI.ImageClickEventArgs) Handles langEnglish.Click Dim SelectedLanguage As String = "en" 'Save selected user language in profile HttpContext.Current.Profile.SetPropertyValue("PreferredCulture", SelectedLanguage) 'Force re-initialization of the page to fire InitializeCulture() Context.Server.Transfer(Context.Request.Path) End Sub But of course the InititalizeCulture then overrides whatever button selection has been made. Is there any way that the InitialCulture can check whether a button click has occurred and if so skip the routine? Any advice would be greatly appreciated, thanks.

  Read the article

• Why isn't jQuery automatically appending the JSONP callback?

  - by Aseem Kishore

  The $.getJSON() documentation states: If the specified URL is on a remote server, the request is treated as JSONP instead. See the discussion of the jsonp data type in $.ajax() for more details. The $.ajax() documentation for the jsonp data type states (emphasis mine): Loads in a JSON block using JSONP. Will add an extra "?callback=?" to the end of your URL to specify the callback. So it seems that if I call $.getJSON() with a cross-domain URL, the extra "callback=?" parameter should automatically get added. (Other parts of the documentation support this interpretation.) However, I'm not seeing that behavior. If I don't add the "callback=?" explicitly, jQuery incorrectly makes an XMLHttpRequest (which returns null data since I can't read the response cross-domain). If I do add it explicitly, jQuery correctly makes a <script> request. Here's an example: var URL = "http://www.geonames.org/postalCodeLookupJSON" + "?postalcode=10504&country=US"; function alertResponse(data, status) { alert("data: " + data + ", status: " + status); } $.getJSON(URL, alertResponse); // alerts "data: null, status: success" $.getJSON(URL + "&callback=?", alertResponse); // alerts "data: [object Object], status: undefined" So what's going on? Am I misunderstanding the documentation or forgetting something? It goes without saying that this isn't a huge deal, but I'm creating a web API and I purposely set the callback parameter to "callback" in the hopes of tailoring it nicely to jQuery usage. Thanks!

  Read the article

< Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >