Search Results

Search found 10852 results on 435 pages for 'tool'.

Page 361/435 | < Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >

  • How to create a static IP on Windows Server 2008 R2 so I can access the server remotely

    - by Aesir
    I have just purchased a HP Proliant N40L which I am intending to use as a NAS, learning tool and just in general something to mess around with. As a student via the Microsoft dreamspark program I can get a free copy of Windows Server 2008 R2 which I am using as the OS. So that I can remote to the box from outside of my local network and so that I can stream media from it to my PS3, I have read that I need to create a static IP for the server and use port forwarding to forward to this IP so I can remote in. Is this correct? I am not really sure how to do this and if I need to make these changes on my router configuration, on the OS or both. I am a novice when it comes to networking however most resources for Windows server 2008 R2 seem to assume a fair amount of experience already. I realise that using this particular OS may seem like overkill for what I currently wish to do with it (stream content to other devices and backup) but as I can get a copy for free it seems sensible. Edit: From reading answers posted I feel I should give more information. I have now tried to add a static IP address using my router configuration settings. I have used the getmac command to get the mac address of the server. My ISP is Virgin Media and I have gone to the LAN IP section and I have added an IP address to the DHCP Reservation Lease Info. I can now use remote desktop connection internally to remote to the server (so I am assuming assigning this IP has worked). How do I configure this on the OS as well? I am also unsure on how I would remote to this machine outside of my local network?

    Read the article

  • Win 7 crashes, PC reboots and says "Hard drive 0 not found" until I turn if off and on again

    - by Danny T.
    I recently made the move from Windows XP to Windows 7. Since then, when my computer is on for a few hours it always ends up rebooting without warning. Then the BIOS won't recognize my hard drive (hard drive 0 not found). If I turn off my computer and then on again, it boots normally. Some details: Dell Dimension 9150 Windows 7 I updated the BIOS I updated all system drivers with the latest version from Dell (SATA, Chipset, etc.) Other drivers updated too (Graphic card, sound, etc.) There is one thing that I tried after some Googling: I turned off the DMA access to the drives, but it's still rebooting after a few hours. Any clue? UPDATE 2010/12/13 Here are the events from the Event Log for today, from when I turned the computer on until it crashed: 19:17 - Error - ID 10016 - DistributedCom 20:06 - Error - ID 1008 - Customer Improvement Program (could not send data to Microsoft) 21:48 - Critical - ID 41 - Kernel-Power (System was restarted without proper shutdown) 21:48 - Error - ID 6008 - EventLog (Previous system down was not planned) 21:48 - Error - ID 1101 - EventLog (Audit Event ignored) 21:49 - Error - ID 10016 - DistributedCom Both DistributedCom events have a description along these lines (translated from French): The authorisation parameters specific to the application are not allowing Local Execeution for the COM server application with the CLSID {C97FCC79-E628-407D-AE68-A06AD6D8B4D1} and the APPID {344ED43D-D086-4961-86A6-1106F4ACAD9B} to the SID AUTHORITY NT\User System (S-1-5-18) from the address LocalHost (LRPC usage). This security authorisation can be changed with the Component service administration tool. UPDATE 2010/12/31 Here are the error messages I have on blue screens : STOP C000007xA - Kernel_Data_Inpage_Error "Unkown hard error" C00000135 - Can't start because &hs is missing

    Read the article

  • Removing Paths/ Landing Pages From SharePoint Search Results

    - by j.strugnell
    Hi there, We've been asked by a client to remove a number of pages from being shown up in their public website search results page. I've been into the SSP and created Crawl Rules to remove these pages. All seemed to have worked ok but we have an issue in that landing pages are still showing up in their "www.domain.com/sitearea/" form but not in their "www.domain.com/sitearea/pages/default.aspx". For each of this type of page we have created one rule to "Exclude" the "aspx" path and another rule to include the "/" path but to "Follow links on the URL without crawling the URL itself". We tried adding rules to exclude the "/" format but that only resulted in all results underneath that being excluded. Does anybody know how to remove the "area/pages/default.aspx" and the "area/" pats from Search Results? I'm not sure if it's the "done thing" to ask 2 questions in one but this is in a similar vein so it should be ok. I was wondering if anyone knew of a tool (or if it is possible) to allow site admins to exclude pages from search results (not via SSP/Crawl Rules). I know they can do it at the site level but I was wondering if anything out there enabled this to be done at the page level through either Page or Site Settings?

    Read the article

  • Goal setting/tracking packages for software projects

    - by Avi
    I'm a developer working by myself. I'm looking for a computerized tool to manage my goals and activities. I own it Microsoft Project, but I don't like it. I've started many "projects" but could never keep on using it. Too complex and heavyweight for me. I use MS-Outlook tasks. They are not what I need. No planning capability. Tracking is not nice. I'm using the Pomodoro technique and I like it, but I'm looking for something more comprehensive and with better computerized support. Something that would allow me to define goals with dependencies and time estimation, keep daily prioritized lists etc. So, I'm looking for a solution. One I've found is GoalPro, but I uneasy because I could not find a cross-product "top ten" like review. Are you using any goal setting package such as GoalPro? Which? Does it help? Pros and Cons?

    Read the article

  • LDAP SSL connect problem

    - by juergen
    I set up a test domain for my LDAP SSL tests and it is not working. I am using Windows Server 2008 R2 SP 1. I came so far: 1. i generated and installed my self signed certificate on the test domain controller 2. on the server i can log into ldap over SSL with the MS ldp.exe tool. 3. using ldp.exe on a client that is no in this domain the login fails with error 0x51 = "failed to connect". (i don't have a client computer that is in this domain right now) 4. I testet the certificate by using it in the IIS on the test server and I can reach the default page of the test server over SSL. (from the client that is not in the domain) 5. analysing the traffic between client and server I can see that the server is sending a certificate to the client. why isn't this working on my client computer?

    Read the article

  • Which revision control system for single user

    - by G. Bach
    I'm looking to set up a revision control system with me as a single user. I'd like to have access (read and write) protected using SSL, little overhead, and preferrably a simple setup. I'm looking to do this on my own server, so I don't want to use the option of registering with some professional provider of such a service (I like having direct control over my data; also, I'd like to know how to set up something like that). As far as I'm aware, what kind of project I want to subject to revision control doesn't really matter, but just for completeness' sake, I'm planning on using this for Java project, some html/css/php stuff, and in the future possibly as a synchronizing tool for small data bases (ignore that later one if it doesn't fit in with the paradigm of revision control). My questions primarily arise from the fact that I only ever used Subversion from Eclipse, so I don't have thorough knowledge of what's out there, what fits better for which needs, etc. So far I've heard of Subversion, Git, Mercurial, but I'm open to any system that's widely used and well supported. My server is running Ubuntu 11.10. Which system should I choose, what are the advantages of the respective systems, and if you know of any particularly useful ones, are there tutorials regarding the setup of the system I should choose that you could recommend?

    Read the article

  • Creating a Jenkins build farm in a hands-off manner?

    - by user183394
    My colleague and I have set up and run Jenkins on a KVM guest running Ubuntu 12.04 with good results for a while now. We are thinking about deploying a cluster of Jenkins CI hosts in master/slave configuration, with the libvirt slave plugin to keep our hardware count low. Our environment is strictly Linux (CentOS, Scientific Linux, Fedora, and Ubuntu). Both of us are competent in setting up large clusters. We typically use tools like cobbler + a configuration management tool (Puppet, Chef, and alike) to set up a large number of machines (physical and/or virtual) hands off (hundreds of nodes in less than an hour typical). We would like to do the same for nodes running Jenkins. But the step by step guide doesn't give us any clues in this regard. I did see a Multi-slave config plugin. But, being used to dealing with hundreds or more machines completely hands-off, clicking the UI for many machines just doesn't feel right. Can someone point to us a reference that talks about how to set up large cluster of Jenkins CI hosts more in the hands-off way?

    Read the article

  • Linux disk usage analyser that acts like symlinks are real files

    - by Rory
    I am using git-annex, an extension to the DVCS git, which is designed for handling large files. It makes heavy use of symlinks. The actual large files are moved to the .git/annex directory and the original files are symlinked to there. I am running out of disk space, and need to clear up, and see what's using all my space. Usually I'd use a disk usage tool like ncdu, Baobab or Filelight. However they treat the symlink as essentially empty, and only count the file that it is pointing to as using any space. Which means when I use git-annex, it shows no space used in the main directories and lots of space used in the .git/annex directory. This is not helpful. Is there any (graphical or ncurses) based disk usage programme for linux (apt-get installable would be easie that is capable (through options or not) of counting a symlink as using up the space that the original file uses up? Many have options for different behaviour for hard links, so makes sense that some should h (I know counting symlinks as using space has flaws, like counting the space space twice, broken symlinks, etc. But that's OK for my purposes)

    Read the article

  • How to convert JPEG JFIF files to JPEG Exif format?

    - by tigrou
    I recently put the SD card of my camera in a Windows 7 PC and start browsing pictures on it. I noticed some were not aligned correctly and use rotate feature included in Windows Photo Viewer in order to view them as I wanted. What I didn't know is that when rotate feature is used, it also overwrite the picture when pressing next or previous button resulting in a possible loss of quality (which is in my opinion a bad idea, app should at least warn user of what will happened when using such a feature). After that, I re-inserted the SD card back in my camera and bad surprise happened : the rotated picture could not be previewed anymore. Instead, i got a black screen saying "Incompatible JPEG format". Other files (untouched) are still working ok. To try to understand what happened I opened a JPEG file from camera and one generated on windows 7 in a hex editor. Here is the difference : The camera JPEG files have a Exif tag in them (with 0xE1 in header). Other JPEG files (Windows 7) have first a JFIF tag in it, followed by a Exif tag (with 0xE0 in header). So if i understand it well, both are JPEG files, but using a different internal format. Here is my question : is it possible (using some tool) to convert JFIF files to Exif format ? I understand that original camera files have been reencoded and thus lose some quality (getting originals back is impossible). What i want know if convert them from JFIF back to Exif (without a second loss of quality if possible...)

    Read the article

  • SNMP closed state in CentOS

    - by anksoWX
    I'm having a problem here, I've added to my IPtables rules this: -A INPUT -p tcp -m state --state NEW -m tcp --dport 161 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 161 -j ACCEPT but when I scan with nmap or any other tool it says this: Not shown: 998 filtered ports PORT STATE SERVICE 22/tcp open ssh 161/tcp closed snmp also when I am doing: netstat -apn | grep snmpd tcp 0 0 127.0.0.1:199 0.0.0.0:* LISTEN 3669/snmpd<br> udp 0 0 0.0.0.0:161 0.0.0.0:* 3669/snmpd<br> unix 2 [ ] DGRAM 226186 3669/snmpd Also: service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination 1 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 3 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 4 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:161 5 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:161 6 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 7 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) num target prot opt source destination Any idea what's going on? There is no UDP in closed/open state. what do I have to do?

    Read the article

  • Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

    - by Shasteriskt
    I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

    Read the article

  • Is there a command to change primary group for a new user in Cygwin?

    - by Rob Gilliam
    Is there a way to set a (new) user's primary group in Cygwin's /etc/passwd file without hand-editing the file? I have a local group set up for members of the Dev Team on a Windows Server 2008 R2 box so that we can all modify a particular group files, but the regular users can only read them. As some of the work we do uses scripts that rely on Cygwin tools, this group is also in the /etc/group file. When I need to add a new user to the "Dev Team" group, I add them in Server Manager, and then use mkpasswd to add that user to Cygwin's /etc/passwd file. Unfortunately, they get the regular Domain Users group assigned as their primary group and I then have to go in and edit the passwd file to change the group. I now need to write some instructions for someone else who is not au fait with UNIX/Linux/Cygwin so that they can set up new Dev Team users and obviously "hand editing" /etc/passwd is a recipe for disaster if you don't know what you're doing. So, is there a way of getting mkpasswd to set a different primary group, or another tool like Linux's usermod which can be used for the purpose of changing the group in a more controlled manner?

    Read the article

  • VirtualBox doesn't see raw partitions

    - by smbear
    What I want to achieve is to set up virtual machine with VirtualBox. Host OS is Windows 7 Home Premium, guest will be (k)Ubuntu 12.04 on a raw partition. The first problem is that when I issue following command: VBoxManage.exe internalcommands listpartitions -rawdisk \\.\PhysicalDrive0 I get following result: Number Type StartCHS EndCHS Size (MiB) Start (Sect) 1 0xee 0 /0 /1 1023/254/63 715404 1 I'm guessing that VirtualBox is unable to see my partitions. If I use diskpart tool, then all partitions are listed correctly (note Polish language version of Windows): DISKPART> select disk 0 Obecnie wybranym dyskiem jest dysk 0. DISKPART> list partition Partycja ### Typ Rozmiar Przesuniecie ------------- ---------------- ------- ------------ Partycja 1 System 200 MB 1024 KB Partycja 2 Zarezerwowany 128 MB 201 MB Partycja 3 Podstawowy 139 GB 329 MB Partycja 5 Nieznany 4883 KB 140 GB Partycja 6 Podstawowy 50 GB 140 GB Partycja 7 Podstawowy 484 GB 190 GB Partycja 4 Odzyskiwanie 24 GB 674 GB Additional note: my PC is using EFI to boot OS. Basing on the results listed above, I believe that: I messed up with my partition table. Something is wrong with VirtualBox. Can anyone help with this issue?

    Read the article

  • Upgrading memory in a laptop

    - by ulidtko
    I'm a bit confused about all the memory types and various bus frequencies of modern consumer PCs. Requesting expert help on the subject. So far I'm confident that: I have an Asus X51L laptop with an unknown set of configuration options. The CPU in there supports PAE, so I still have a chance to extend the memory beyond 3GiB; and the upper limit of the system is 8GiB. (?) The laptop has two SODIMM slots, one of which is occupied by a 2GiB bank, and the other one is empty. dmidecode and lshw tools consistently state 533 Mhz frequency of the bank. The last one confuses me the most. I failed to find out characteristics of the northbridge in this laptop, and still can't figure out what DDR2 to seek for. Is it DDR2-1066? Or, rather, PC2-8500/PC2-8600? Wouldn't a DDR2-800 bank harm the system's performance? Which kind of modules should I look up in stores? Update: I have bought a 2 GiB DDR2-800 SODIMM, and it seams that the system can't handle 4 GiB of memory. When installed by itself in either slot, both new and old bank (which btw happens to be marked GDDR2-677) work just perfectly; i.e. any configuration resulting in 2 GiB works. When both banks are installed though (totalling in 4 GiB), the memcheck86 tool produces horrible artifacts and crashes, and system reboots; an Ubuntu system can be started and even logged into a Unity session, but the system reboots too in this case from even a minor RAM load. So it's pretty obvious to me now that this laptop doesn't support 4 GiB of RAM or more.

    Read the article

  • Server slowdown

    - by Clinton Bosch
    I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

    Read the article

  • one 16K random read I/O issues 2 scsi I/O (16K and 4K) requests in linux

    - by hiroyuki
    I noticed weird issue when benchmarking random read I/O for files in linux (2.6.18). The Benchmarking program is my own program and it simply keeps reading 16KB of a file from a random offset. I traced I/O behavior at system call level and scsi level by systemtap and I noticed that one 16KB sysread issues 2 scsi I/Os as following. SYSPREAD random(8472) 3, 0x16fc5200, 16384, 128137183232 SCSI random(8472) 0 1 0 0 start-sector: 226321183 size: 4096 bufflen 4096 FROM_DEVICE 1354354008068009 SCSI random(8472) 0 1 0 0 start-sector: 226323431 size: 16384 bufflen 16384 FROM_DEVICE 1354354008075927 SYSPREAD random(8472) 3, 0x16fc5200, 16384, 21807710208 SCSI random(8472) 0 1 0 0 start-sector: 1889888935 size: 4096 bufflen 4096 FROM_DEVICE 1354354008085128 SCSI random(8472) 0 1 0 0 start-sector: 1889891823 size: 16384 bufflen 16384 FROM_DEVICE 1354354008097161 SYSPREAD random(8472) 3, 0x16fc5200, 16384, 139365318656 SCSI random(8472) 0 1 0 0 start-sector: 254092663 size: 4096 bufflen 4096 FROM_DEVICE 1354354008100633 SCSI random(8472) 0 1 0 0 start-sector: 254094879 size: 16384 bufflen 16384 FROM_DEVICE 1354354008111723 SYSPREAD random(8472) 3, 0x16fc5200, 16384, 60304424960 SCSI random(8472) 0 1 0 0 start-sector: 58119807 size: 4096 bufflen 4096 FROM_DEVICE 1354354008120469 SCSI random(8472) 0 1 0 0 start-sector: 58125415 size: 16384 bufflen 16384 FROM_DEVICE 1354354008126343 As shown above, one 16KB pread issues 2 scsi I/Os. (I traced scsi io dispatching with probe scsi.iodispatching. Please ignore values except for start-sector and size.) One scsi I/O is 16KB I/O as requested from the application and it's OK. The thing is the other 4KB I/O which I don't know why linux issues that I/O. of course, I/O performance is degraded by the weired 4KB I/O and I am having trouble. I also use fio (famous I/O benchmark tool) and noticed the same issue, so it's not from the application. Does anybody know what is going on ? Any comments or advices are appreciated. Thanks

    Read the article

  • How do I do a mail merge that includes images?

    - by Ian Ringrose
    I am trying to find out the practicalities of doing a mail merge when each “record” to be merged on includes some images. I need to: print letters And envelopes Both the letters and the envelopes have: Fixed text Fixed images Text that come from the mail merge record Images that come from the mail merge record I don’t know if all images will be the same size for every record, so a bit of simple “on the fly” automatic formatting may be needed . I need to be able to repeat a single item if I get a problem (e.g when folding the letter). What problems am I likely to have? Is Word 2007 up to this sort of mail merging, or should I be looking at a report writing tool? How do I restart a print run after a printer jam etc? What format should I store the “records” and there images in? E.g Can standard software cope with images that are stored in separate files named after the “CustomerId” that is in the “record” (I can write custom software if needed, but would rather use standard “of-the-shelf” software for the printing, I am planning on custom software for the data creation, so can output in whatever format is needed)

    Read the article

  • Office 2010 OCT Outlook Filepaths

    - by vlannoob
    I'm playing around with customizing Office 2010 installs on my network, normally I just do a full manual install, but as the environment grows and the lazier I get its becoming a pain to do it manually every time. I've read up and downloaded the Office 2010 OCT tool and it looks relatively straight forward - with one exception - the Outlook Profile. I can 'get around it' by just leaving it all as default (or not enabling offline use) but I'd like to customise it slightly so that its all setup no matter who logs onto the PC. The only issue I have, and my question is: In the OCT - Outlook section What do you enter into the Path and Filename for the OST file and the Offline Address book seetings under Enable Offline Use section? I'm sweet with everything else - just that one section, and I think if I bugger that one it will kill the whole Outlook Profile?? It would need to go into each users unique filepath for their profile correct? I have a fair idea of what should be there but I'm struggling with the correct syntax. I know this is a stupid question....but its late in the day and my brain is fried ;) As usual - any and all help/assistance is appreciated ;)

    Read the article

  • program to track recent saved files or downloads?

    - by DiegoDD
    Back to windows XP times, i used a program named Ava Find that can find any file in the system, but a really nice feature it had, called "scout bot" that automatically finds new files, that is, recently created. More info here: AvaFind For example, if i saved or downloaded a file (in any program), but i cant remember its name or where i put it, i just simply looked at the scoutbot list, and it showed me the most recent files, and then i could just open them from there, or jump to their path. Since i changed to windows 7 (passing through vista), the program no longer works. It simply keeps indexing forever and never finds anything. I don't know if it is not compatible with win 7 itself, or because the fact that my windows 7 is 64 bit. I already tried to contact the Avafind creators, but they never answered, and the program seems to be no longer supported (although the site still works). Now, is there a similar program that finds RECENT files? e.g. listing the most recently saved files, system-wide (or even limiting it to some folders, discs)? And that of course, that is confirmed to work with win 7 64 bit. I know that there are many programs that can find any file, like everything, but what i want is to find recent files and their paths, without knowing their name or e. "everything" also can sort results by date, which is almost what i need, simply to look for part of the file name or extension, and get the most recent one. but if i get to many results, it takes a while, plus, i STILL need to know the name or at least extension of the file. What i want is simply a "Most recently Saved files" tool. i.e., a replacement for Scout Bot in Ava Find. Do you know any alternative?

    Read the article

  • Recover data from quick formatted DVD-R

    - by Andrii Kalytiiuk
    I need to recover data from quick-formatted DVD-R. Please advise a free of charge option (cheap commercial tools will be ok either). Disk was partially recorded with Windows built in disk recorder and recording most likely was not complete. Afterwards I have inserted partially recorded DVD again and on Windows recorder's message box 'How to use this disk?' selected - 'use for CD/DVD player' and data was completely lost - as new recording session was started. Files of photos were recorded on disk. What I have tried so far: DiskInternals CD-DVD recovery - sees 5 jpg files but can't show preview. Tool is commercial - trial version does not allow to recover files. CDCheck - doesn't see any files and reports errors at attempt to scand DVD CD Recovery Toolbox Free - does not even recognize DVD drive ISO Buster - recognizes two files - one MP3 file for 99% of recorded size and one ARC file for about 100 KB MiniTool Power Data Recovery - Free Edition - does not see any files on DVD Stellar Phoenix CD DVD Data Recovery - does not see any files BinaryBiz Virtual Lab - sees DVD disk but needs license to browse content Please advise how is it possible to recover files from DVD.

    Read the article

  • Google Apps, SPF, softfail problem (validates with validation tools, but still softfails otherwise)

    - by mq.chen
    Hi, I guess this is probably a commonly asked and boring question but I'm really at a loss and I don't know what else to do. This might be a duplicate of other questions, but none of the solutions worked for me. I've Googled around and read just about anything I could find but I'm still puzzled as to why it doesn't work. The gist of my problem is that I have set-up Google Apps for a client of mine with the domain fintan.dk. Everthing works just excellent, except emails sent from *@fintan.dk (either with the Gmail web-interface or desktop client) to a non-Google Apps email gets a softfail (I have sent to my University email, an email hosted at MediaTemple and even Hotmail). The emails gets a pass when sent to a Google Apps or Gmail address though... (All emails from that domain are sent via email clients.) So this is what I have done so far: I've added the SPF record Google recommended (v=spf1 include:_spf.google.com ~all), waited several days hoping it would a DNS update delay problem. Now, three days later there is no change. I have verified the settings in the desktop clients several times. I have validated the records with validation tools like the SPF Query Tool, [email protected] and [email protected]. All of them validate and gives a pass, saying there shouldn't be a problem, but strangely there still is. So, I really don't know what else to do. Any help is very much appreciated. Thank you in advance!

    Read the article

  • Recommended Win2k8 Server software to fix my RAID-0 issue

    - by Jason Kealey
    I'm running an Asus P6T V2 Deluxe. It has six SATA ports and supports onboard RAID. I am using two of those ports for a RAID0 array of 1.5TB Seagate drives using the onboard RAID controller. One of them is giving me SMART warnings and I want to preemptively replace it. I pulled out two other 1.5TB drives from another computer and am ready to use one or both, if necessary. I can't run any SMART diagnostic software from within Windows because it only sees the hardware RAID-0 array, not each individual drive. The first thing I tried was a slow sector-by-sector copy using a free tool called EASEUS Disk Copy. Used the bootdisk, copied (took like 16 hours), unplugged the defective drive and plugged the new one in its place. The motherboard didn't recognize the new drive as being part of the known setup, so it did not want to boot. The second thing I tried was using other software (I forget the name) to copy the partition from within Windows. The first software failed because I had a server operating system. I found another software (I forget the name) which supported a server OS and did a partition copy onto the new drive. This seemed to work and the OS started to boot, but blue screened and started a reboot cycle. I'm assuming the software I was using was no good as it was trying to copy the boot disk while it was in use. I am looking for recommendations on what software to use to fix my problem without doing a re-install. Everything is backed up but my computer works fine and I'd like to avoid re-installation when possible. However, my system would be back up now if I had just started over on a second RAID array. :)

    Read the article

  • Good HTTP Monitoring tools

    - by ffffff
    I look for HTTP to work with a Linux system server monitor tool every protocol. I know, and will not there be it in whom or a freeware? When, for example, I dump 80/tcp with a packet monitor to be concrete # tethereal -i ppp0 port 80 -x Capturing on ppp0 1244206390.030474 219.111.xx.xx -> 74.125.xx.xx HTTP GET /search?output=js&num=0&dt=1244206414703&client=pub-3031568651010206&q=Cagliari%20Flight&ad=n3&ie=utf8&oe=utf8&channel=0091594208&adtest=off HTTP/1.1 0000 00 04 02 00 00 00 00 00 00 00 00 00 00 00 08 00 ................ 0010 45 00 01 e5 ee 82 40 00 40 06 d2 b5 db 6f 02 5b E.....@[email protected].[ 0020 4a 7d 4f 93 d4 29 00 50 3e df 4c 63 4b 6b 42 e0 J}O..).P>.LcKkB Such output is provided, but there is too much unnecessary information such as an SYN packet or a header. What I want The IP address of the client and sending out character string(Get; the contents of the POST) Among the output character string of the server only as for the HTML (Content-Type:) I am what is chisel) of a thing of text/html. I can set a filter and am the best if only information wanting can accumulate in the log.

    Read the article

  • Server 2008R2 Server Manager Roles and Features won't refresh or allow addition of new roles or features

    - by MattChorba
    I have a standalone DC in an isolated lab. I have installed the SUR tool and found no errors. I ran SFC and found no errors. I have attempted to install Windows Backup feature using Powershell, but received the same error about the computer needing to be restarted. Powershell cmdlets will list all of the installed roles and features. The rest of Server Manager works without problems. What can I do to get Server Manager Roles and Features working properly again? Picture of Error: CheckSUR.log: ================================= Checking System Update Readiness. Binary Version 6.1.7601.21645 Package Version 13.0 2011-11-28 13:20 Checking Windows Servicing Packages Checking Package Manifests and Catalogs Checking Package Watchlist Checking Component Watchlist Checking Packages Checking Component Store Summary: Seconds executed: 413 No errors detected (w) Unable to get system disk properties 0x0000045D IOCTL_STORAGE_QUERY_PROPERTY Disk Cache CheckSUR.persist.log: ================================= Checking System Update Readiness. Binary Version 6.1.7601.21645 Package Version 13.0 2011-11-28 13:20 Checking Windows Servicing Packages Checking Package Manifests and Catalogs Checking Package Watchlist Checking Component Watchlist Checking Packages Checking Component Store Summary: Seconds executed: 413 No errors detected (w) Unable to get system disk properties 0x0000045D IOCTL_STORAGE_QUERY_PROPERTY Disk Cache

    Read the article

  • Web based KVM management for Ubuntu

    - by Tim
    We've got a single Ubuntu 9.10 root server on which we want to run multiple KVM virtual machines. To administer these virtual machines I'd like a web based KVM management tool, but I don't know which one to choose from the list of tools mentioned on linux-kvm.org. I've used virsh & virt-manager on my desktop, but would like a web interface for the server. I tested ConVirt on my desktop, but it failed to pickup KVM machines from virsh / virt-manager, and I could not get KVM virtual machine import to work (only Xen). oVirt looks good, but I can't find out if and how I can install it on Ubuntu 9.10.. (And I'd really rather not waste another few days on testing stuff that might not work in the end.) Can anyone recommend any good web based KVM management tools that are easy to install on Ubuntu 9.10? I'm looking for something that will also allow me to run other services like apache and postgresql besides hosting virtual machines, so preferably fairly lightweight & no dedicated OS installs. We don't need any professional clustering / migration or anything, just something that will let us create, start, inspect, administer & stop virtual machines from a web page. Best regards, Tim Update: Anyone have any suggestions? It's awfully quiet here..

    Read the article

< Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >