Search Results

Search found 24755 results on 991 pages for 'linux mom'.

Page 362/991 | < Previous Page | 358 359 360 361 362 363 364 365 366 367 368 369  | Next Page >

• Multiple interfaces to one IP address?

  - by Delan Azabani

  At present, I have: a Netgear router with DHCP off at 192.168.0.1 my computer eth0 at 192.168.0.2 wlan0 at 192.168.0.2 The wlan0 interface always connects to the router, while the eth0 interface connects to other computers with crossover and acts as a dnsmasq DHCP server for network boot and installation. If I use the Gnome NetworkManager to enable both connections, that is, with wlan0 connected to the router/internet and eth0 to another computer, both as 192.168.0.2, I cannot access the internet while eth0 is connected. Why is this? How can I configure my computer to follow wlan0 for Internet usage, but use eth0 for itself (the latter is working but blocking wlan0).

  Read the article

• Partition table corrupted (USB flash drive)

  - by 13ren

  It's an 8 GB Patriot thumb drive, which I've used extensively with lots of data. Today, it is detected, but all data is gone: (EDIT at least some data is still there, but the partition table is gone) EDIT @Sathya (thanks) here's the relevant output from sudo fdisk -l: Disk /dev/sdc: 8019 MB, 8019509248 bytes 247 heads, 62 sectors/track, 1022 cylinders Units = cylinders of 15314 * 512 = 7840768 bytes Disk /dev/sdc doesn't contain a valid partition table It looks like it is /dev/sdc, with that 8 GB... and no partition table. I tried to mount /dev/sdc (and then dmesg | tail): /media> sudo mount /dev/sdc mytmp mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so /media> dmesg | tail [ 24.300000] sdc: unknown partition table [ 24.320000] sd 2:0:0:0: Attached scsi removable disk sdc [ 24.370000] usb-storage: device scan complete [ 26.870000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 26.870000] EXT2-fs: group descriptors corrupted! [ 50.420000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 5565.470000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 5565.470000] EXT2-fs: group descriptors corrupted! EDIT @Col: results from testdisk Disk /dev/sdc - 8013 MB / 7642 MiB - CHS 1022 247 62 Current partition structure: Partition Start End Size in sectors Partition sector doesn't have the endmark 0xAA55 After I hit [proceed], it says: Structure: Ok. Keys A: add partition, L: load backup, Enter: to continue The "Structure: Ok." seems reassuring... will "A: add partition" make my old data accessible (if it's still there), or will it make a new, fresh partition? Another option is "[ MBR Code ] Write TestDisk MBR code to first sector" - would it be better to do this? EDIT I found that at least some of my data is still on the flash drive, by using the below, and searching for English text in less (like " the "): cat /dev/sde | tr -cd '\11\12\40\1540-\176' | less (The drive changed from "/dev/sdb" to "/dev/sde" because I connected some extra drives today). I've learnt that "/dev/sde1" would be the first partition; and "/dev/sde" is the whole drive. Because unix treats these devices just like files, you can use all the ordinary unix file commands on them, like cat, and then process them like any other stream of data. The tr above removes non-printable characters ("\40" is space, which I wanted to preserve). In less, you can use "/" to search, similar to Vim. How can I get my data back (assuming it's still there)? If only the partition table is corrupted, is there a standard "partition recovery tool"? Is there a way to "repartition" without deleting everything?

  Read the article

• Sendmail Tuning For Batch Mail Jobs

  - by Kyle Brandt

  I have a webservers that send out emails to a sendmail relay server as a batch job. The emails need to be accepted by the relay sendmail server as fast as possible, however, they do not need to go out (be relayed) very quickly. I am seeing a couple timeouts once and a while from the webserver trying to connect to the relay server. The load currently is about 30 emails a second for a couple minutes. There are quite a few tuning options for sendmail in the sendmail tuning guide. What I am focusing on now is the Delivery Mode: Delivery Mode There are a number of delivery modes that sendmail can operate in, set by the DeliveryMode ( d) configuration option. These modes specify how quickly mail will be delivered. Legal modes are: i deliver interactively (synchronously) b deliver in background (asynchronously) q queue only (don't deliver) d defer delivery attempts (don't deliver) There are tradeoffs. Mode i gives the sender the quickest feedback, but may slow down some mailers and is hardly ever necessary. Mode b delivers promptly but can cause large numbers of processes if you have a mailer that takes a long time to deliver a message. Mode q minimizes the load on your machine, but means that delivery may be delayed for up to the queue interval. Mode d is identical to mode q except that it also prevents lookups in maps including the -D flag from working during the initial queue phase; it is intended for ``dial on demand'' sites where DNS lookups might cost real money. Some simple error messages (e.g., host unknown during the SMTP protocol) will be delayed using this mode. Mode b is the usual default. If you run in mode q (queue only), d (defer), or b (deliver in background) sendmail will not expand aliases and follow .forward files upon initial receipt of the mail. This speeds up the response to RCPT commands. Mode i should not be used by the SMTP server. I currently have the CentOS default modes: Sendmail.cf: DeliveryMode=background Submit.cf: DeliveryMode=i Is sendmail.cf/mc for outgoing email from relay (to the intertubes) and sumbit.cf/mc for incoming eamil (from my webservers). Would it make sense to change the outgoing delivery mode to queue? If I did, what would the outbound email flow behave like? If this is the right thing to do, can anyone show me example mc configurations for this change? If it isn't, what recommendations are there for these constraints?

  Read the article

• How hard for a Software Developer to Maintain a Server

  - by Samy

  I'm a software developer and don't have much experience as a sysadmin. I developed a web app and was considering buying a server and hosting the web app on it. Is this a huge undertaking for a web developer? What's the level of difficulty of maintaining a server and keeping up with the latest security patches and all that kind of fun stuff. I'm a single user, and not planning to sell the service to others. Can someone also recommend an OS for my case, and maybe some good learning resources that's concise and not too overwhelming.

  Read the article

• nginx: php-fastcgi running but php files not executing

  - by Daniel

  I have recently set up a nginx server with PHP running as FastCGI process. The server is running with HTML files however PHP files are downloading instead of displaying and PHP code is not processed. This is what I have in nginx.conf: server { listen 80; server_name pubserver; location ~ \.php$ { root /usr/share/nginx/html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/nginx/html$fastcgi_script_name; include fastcgi_params; } } The command netstat -tulpn | grep :9000 displays the following which indicates php-fastcgi is running and listening on port 9000: tcp 0 0 127.0.0.1:9000 0.0.0.0:* LISTEN 2663/php-cgi If it's if any importance my server is running on CentOS 6 and I installed nginx and PHP using the repositories from The Fedora Project.

  Read the article

• Adding a jar file to CLASSPATH is still not executable

  - by Simon O'Hanlon

  Perhaps I just don't understand how the whole CLASSPATH environment variable works when trying to find .jar files on your system. I thought if you specified it, you could launch .jar files with java in much the same way that you can launch executables that are on your path. I have an executable java archive (.jar file) on my system, that I stuck in /usr/local/bin/gatk/. I added this to my CLASSPATH via: export CLASSPATH=/usr/local/bin/gatk/GenomeAnalysisTK.jar I thought this would make the .jar file visible to my JVM. When I try to invoke it with java -jar GenomeAnalysisTK.jar #Error: Unable to access jarfile .gatk/GenomeAnalysisTK.jar I can invoke it setting the absolute path, e.g. java -jar /usr/local/bin/gatk/GenomeAnalysisTK.jar, however I'd rather not type the full path each time. I have read many of the linked tutorials but somehow I don't seem to be getting this right and I can't understand what I am doing wrong.

  Read the article

• What happens to running processes when I lose a remote connection to a *nix box?

  - by David Marble

  I occasionally lose my remote SSH connection to my VPS. I use screen for long-running processes, but am wondering what happens to the processes I had running aside from those run within a screen session if I lose the connection to the box. When I re-establish a connection to the box, what happened to the bash and sshd processes that were running when I lost the connection? Today I lost connection repeatedly and noticed many more bash and sshd processes than usual. If there are processes hanging around, do I need to kill them? How could I determine which processes were abandoned from my previous session? Thanks for any replies!

  Read the article

• postfix configuration

  - by kibs

  failed to start the postfix service output given was postfix: fatal: config variable inet_interfaces: host not found: all

  Read the article

• refresh screen rate ubuntu

  - by user24224

  Hello all I am having problems with the refresh rate if the screen . In the the refresh mode of the monitor in the monitor options have only one option 60Hz. I have LG 24 + ATI Radon 3870. And already installed the ati driver via ubuntu download centre. Any idea how i solve that one ? Thanks.

  Read the article

• Screen multiuser - Permission denied

  - by Zlug

  I'm trying to send input to a screen session from php. So far I have followed the steps explained here Is running GNU Screen suid root the only way to make multiuser mode work? And I have set "multiuser on" and "acladd www-data" in the screenrc file (or well, no. in another file that I use by the -c option but still) My problem now is that whenever i try to acess screen by php exec('screen -S user/session -p 0 -X stuff "test"'."\n", $ret); I get the error: Cannot opendir /var/run/screen/S-user: Permission denied

  Read the article

• winbind failing after a semi-random amount of time

  - by The Digital Ninja

  I have winbind set up to authenticate to our AD for samba shares. This is the third such server, and the only one having any issues. It seems after a random amount of time samba shares will just stop working. Winbind processes seem to be running but restarting them seems to fix the issue for a while. Looking at the logs have been kind of hit an miss and I don't know exactly when it fails. One interesting thing is that it seems to be pulling from another domain controller that it shoudlnt. I censored out the domain name in this example. But isnt there some way to block authentication to a domain? I'm not sure if this is a symptom or a cause of the issue. [2010/10/18 08:02:10, 0] winbindd/winbindd_cache.c:initialize_winbindd_cache(2577) initialize_winbindd_cache: clearing cache and re-creating with version number 1 [2010/10/18 09:15:54, 1] libsmb/clikrb5.c:ads_krb5_mk_req(686) ads_krb5_mk_req: krb5_get_credentials failed for [email protected] (Cannot find KDC for requested realm) [2010/10/18 09:15:54, 1] libsmb/cliconnect.c:cli_session_setup_kerberos(624) cli_session_setup_kerberos: spnego_gen_negTokenTarg failed: Cannot find KDC for requested realm [2010/10/18 09:15:54, 0] lib/util_sock.c:write_data(1139) write_data: write failure. Error = Connection reset by peer [2010/10/18 09:15:54, 0] libsmb/clientgen.c:write_socket(242) write_socket: Error writing 108 bytes to socket 18: ERRNO = Connection reset by peer [2010/10/18 09:15:54, 0] libsmb/clientgen.c:cli_send_smb(290) Error writing 108 bytes to client. -1 (Connection reset by peer)

  Read the article

• Why mutt terminates with segmentation error?

  - by hugemeow

  I pressed $, in order to sync mailbox, but mutt just quit... in fact mutt don't quit every time i press $, it only quits sometimes, so how to know the reason why mutt quit? is this a bug in mutt'? The error message is: Sorting mailbox... Segmentation fault Can i use strace with mutt if i want to know what happens? Or are there tools which are better to find out more about the problem? right now i replied to a mail, then i press $, then segmentation fault...

  Read the article

• how to make a php crontab silent

  - by BandonRandon

  I set up a crontab in Cpanel to run every min. It's working great but I don't want an e-mail every min. I have a second cron tab that runs every day. I would like the responce of this tab. Is there a way to tell the crontab to be silent or only e-mail on error? I have: * * * * * php /home/public_html/folder/file.php 2>&1 The last bit 2>&1 I added because i thought it would make it silent. From the Cpanel Docs: You can have cron send an email everytime it runs a command. If you do not want an email to be sent for an individual cron job you can redirect the command's output to /dev/null like this: mycommand /dev/null 2&1

  Read the article

• Xinetd , vncserver memory requirement

  - by JP19

  Hi, I am installing the following on a low memory system: vnc4server xinetd xterm openbox obconf I will only occasionally be logging into the vncs for some admin work. My question is: 1) Does xinetd take memory / cpu even when vncserver is not running? If so, can I "run" xinetd on demand (how)? And if no, any idea how much memory it will take when vncserver is not running? 2) Does vncserver take substantial memory when no clients are connected? 3) Do openbox/obconf take memory when vncserver is running but no client are connected? 4) Do openbox/obconf take memory when no vncserver is running? thanks JP

  Read the article

• How to copy symlinks to target as normal folders

  - by Marek

  Hi i have a folder with symlinks: marek@marek$ ls -al /usr/share/solr/ razem 36 drwxr-xr-x 5 root root 4096 2010-11-30 08:25 . drwxr-xr-x 358 root root 12288 2010-11-26 12:25 .. drwxr-xr-x 3 root root 4096 2010-11-24 14:29 admin lrwxrwxrwx 1 root root 14 2010-11-24 14:29 conf -> /etc/solr/conf i want to copy it to ~/solrTest but i want to copy files from symlink as well when i try to cp -r /usr/share/solr/ ~/solrTest i will have symlink here: marek@marek$ ls -al ~/solrTest razem 36 drwxr-xr-x 5 root root 4096 2010-11-30 08:25 . drwxr-xr-x 358 root root 12288 2010-11-26 12:25 .. drwxr-xr-x 3 root root 4096 2010-11-24 14:29 admin lrwxrwxrwx 1 root root 14 2010-11-24 14:29 conf -> /etc/solr/conf

  Read the article

• not able to register sip user on red5server, using red5phone

  - by sunil221

  I start the red5, and then i start red5phone i try to register sip user , details i provide are username = 999999 password = **** ip = asteriskserverip and i got --- Registering contact -- sip:[email protected]:5072 the right contact could be --- sip :99999@asteriskserverip this is the log: SipUserAgent - listen -> Init... Red5SIP register [SIPUser] register RegisterAgent: Registering contact <sip:[email protected]:5072> (it expires in 3600 secs) RegisterAgent: Registration failure: No response from server. [SIPUser] SIP Registration failure Timeout RegisterAgent: Failed Registration stop try. Red5SIP Client leaving app 1 Red5SIP Client closing client 35C1B495-E084-1651-0C40-559437CAC7E1 Release ports: sip port 5072 audio port 3002 Release port number:5072 Release port number:3002 [SIPUser] close1 [SIPUser] hangup [SIPUser] closeStreams RTMPUser stopStream [SIPUser] unregister RegisterAgent: Unregistering contact <sip:[email protected]:5072> SipUserAgent - hangup -> Init... SipUserAgent - closeMediaApplication -> Init... [SIPUser] provider.halt RegisterAgent: Registration failure: No response from server. [SIPUser] SIP Registration failure Timeout please let me know if i am doing anything wrong. regards Sunil

  Read the article

• Nginx Forward SSL for single site

  - by Will.brown

  I have a nginx server setup and it works fine for http however i would like to bypass the proxy for https connection. I want it so that when someone goes to my ip https:// ip1 (Nginx server) it bypasses ngix and forwards all traffic to https:// ip2(webserver) i do not need ngix to do this for any ssl website just one particular website. SO Client to https:// ip1 to https:/ /ip2 to https:// ip1 to client pc I just want the nginx to not intercept the connection and forward it on and on return forward the connection to client Im guessing i do this by nat mascarade buy not exactly sure how to do it and if i will need to tell nginx to ignore ssl aswell can someone help me please this has gone me stuck

  Read the article

• Using NOPASSWD for specific commands in sudoers file, PASSWD for all others

  - by jberryman

  I would like to configure sudo such that users can run some specific commands without entering a password (for convenience) and can run all other commands by entering a password. This is what I have, but this does not work; a password is always required: Defaults env_reset Defaults timestamp_timeout = 1 root ALL=(ALL:ALL) ALL # Allow members of group sudo to execute any command %sudo ALL=(ALL:ALL) NOPASSWD: /usr/sbin/pm-suspend, /usr/bin/apt-get, PASSWD: ALL #includedir /etc/sudoers.d Note that this is a debian system which uses this adding users to the "sudo" group method. Thanks.

  Read the article

• Symbol lookup error while starting pidgin in Arch

  - by Hossein Mobasher

  I have just installed pidgin from the source code that i downloaded from pidgin site, it compile correctly with using below commands : ./configure --disable-gtkspell ; make ; make install but, when i try to start pidgin from terminal, occurres an error :? pidgin: symbol lookup error: /usr/lib/libfarstream-0.1.so.0: undefined symbol: g_key_file_free how can i solve this problem ? Thanks for your attention :)

  Read the article

• Disable MathML output of eLyXer

  - by Gryllida

  eLyXer is a standalone LyX to HTML converter. In the resulting file, equations are formatted as MathML, and the file itself starts with an XML tag. This causes two problems: LibreOffice does not read the XML file (it can read HTML files, but not XHTML). I am unable to copy and paste the equations into a document editor such as LibreOffice with the goal of subsequent conversion into .doc, because .doc files do not support MathML. The eLyXer help page mentions an option to only use simple math, but there is no option to set math equations to output as images. And I already set Document Settings Output Math equations Format: images in LyX, which presumably is saved in the lyx document somewhere. A web search did not come up with any solutions.

  Read the article

• Why is scp not overwriting my destination file?

  - by Noli

  I'm trying to back up a file via the command scp /tmp/backup.tar.gz hostname:/home/user/backup.tar.gz When I run it, the scp progress bar shows up and it looks like its transferring the file, however when I log into the destination server to check the file, the timestamp and filesize haven't changed from the older version, so it looks like scp didn't overwrite the old file at all. It only sees to work when I manually delete the file from the destination server. I'm running ubuntu, and this is happening on two servers: one cygwin ssh, and one fedora core 3. Anyone have any idea why this is happening? I thought scp would ONLY overwrite existing files.. Thanks

  Read the article

• Journaled filesystems and power failure

  - by Yoga

  I heard that even a journaled filesystems such as EXT3/EXT4 might corrupted during power failure, e.g. from wikipedia [1]: In the event of a system crash or power failure, such file systems are quicker to bring back online and less likely to become corrupted. Can anyone provide more detail by giving examples such that when corruption can occur corruption is avoided by journaled filesystems [1] http://en.wikipedia.org/wiki/Journaling_file_system

  Read the article

• Using find and tar with files with special characters in the name

  - by Costi

  I want to archive all .ctl files in a folder, recursively. tar -cf ctlfiles.tar `find /home/db -name "*.ctl" -print` The error message : tar: Removing leading `/' from member names tar: /home/db/dunn/j: Cannot stat: No such file or directory tar: 74.ctl: Cannot stat: No such file or directory I have these files: /home/db/dunn/j 74.ctl and j 75. Notice the extra space. What if the files have other special characters? How do I archive these files recursively?

  Read the article

• invalid argument in bash script when port is bad

  - by user273689

  When I do this command I get an error when there is something wrong with the eth3. RESC="1234" RESD="1234" RESO="1234" RESC=$(ssh -q vmx@$1 cat /sys/class/net/$2/carrier) RESO=$(ssh -q vmx@$1 cat /sys/class/net/$2/operstate) RESD=$(ssh -q vmx@$1 cat /sys/class/net/$2/dormant) cat: /sys/class/net/eth3/carrier: Invalid argument cat: /sys/class/net/eth3/dormant: Invalid argument How can I use the invalid argument inside the RESC and RESD variable Thanks

  Read the article

• Grant HTTP access based on unix user group

  - by Sander Marechal

  Is it possible to grant network access or HTTP access based on a user's group? At my company we want to set up an internal composer server using Satis to manage packages for the projects we write (e.g. on repository.mycompany.com), with the packages themselves in our SVN server (svn.mycompany.com). We have several webservers with many different users on them. Some users should be able to reach the composer and SVN server. Some should not. Users that should be able to reach these servers all belong to the same group. How can I set up Apache on the Composer and SVN server to only grant access to those users in that group? Alternatively, can I set up the webservers in such a way that only users from that group are able to make a connection to our Composer and SVN servers? The best thing we have come up with so far is using SSL client certificates. We simply place a client certificate on all servers which can be used to access Composer and SVN. Only the right usergroup will have read access to the certificate. A bit clunky but it may work. But I'm looking for something better.

  Read the article

< Previous Page | 358 359 360 361 362 363 364 365 366 367 368 369  | Next Page >