Search Results

Search found 18534 results on 742 pages for 'dave long'.

Page 363/742 | < Previous Page | 359 360 361 362 363 364 365 366 367 368 369 370  | Next Page >

• x11vnc is slow, but using only 10% of available bandwidth

  - by mmm

  I am using x11vnc over 15Mbit/s network with 20ms latency. When the screen is changing a lot x11vnc is slow - for example when I switch a tab in a browser, it takes almost two seconds until the view is fully redrawn. The strange thing is that max connection speed of x11vnc is even during slow redrawing only about 10% of the available bandwidth. Why is x11vnc not using available bandwidth to speed the redrawing up? For example scp is using 100% of available bandwidth without problems. How can I identify what is the bottleneck for x11vnc on my system? So far I think: 10% network usage = network is not a bottleneck fb read rate: 601 MB/sec = reading fb is not a bottleneck Any ideas how can I further profile x11vnc and find out what is causing a slowdown? For example is there any switch for x11vnc to show how much data it is handling and how long it takes to grab a screen, process and compress it and send it over the network?

  Read the article

• DC Comics Identifies Krypton on the Star Map

  - by Jason Fitzpatrick

  This week Action Comics Superman #14 hits the stands and DC comics reveals the actual location of Kyrpton, delivered by none other than beloved astrophysicist Neil Tyson. Phil Plait at Bad Astronomy reports on the resolution of fans’ long standing curiosity about the location of Krypton: Well, that’s about to change. DC comics is releasing a new book this week – Action Comics Superman #14 – that finally reveals the answer to this stellar question. And they picked a special guest to reveal it: my old friend Neil Tyson. Actually, Neil did more than just appear in the comic: he was approached by DC to find a good star to fit the story. Red supergiants don’t work; they explode as supernovae when they are too young to have an advanced civilization rise on any orbiting planets. Red giants aren’t a great fit either; they can be old, but none is at the right distance to match the storyline. It would have to be a red dwarf: there are lots of them, they can be very old, and some are close enough to fit the plot. I won’t keep you in suspense: the star is LHS 2520, a red dwarf in the southern constellation of Corvus (at the center of the picture here). It’s an M3.5 dwarf, meaning it has about a quarter of the Sun’s mass, a third its diameter, roughly half the Sun’s temperature, and a luminosity of a mere 1% of our Sun’s. It’s only 27 light years away – very close on the scale of the galaxy – but such a dim bulb you need a telescope to see it at all (for any astronomers out there, the coordinates are RA: 12h 10m 5.77s, Dec: -15° 4m 17.9 s). 6 Ways Windows 8 Is More Secure Than Windows 7 HTG Explains: Why It’s Good That Your Computer’s RAM Is Full 10 Awesome Improvements For Desktop Users in Windows 8

  Read the article

• Apple MagicMouse randomly loses connection

  - by Yuval

  My Magic Mouse periodically randomly loses connection to my macbook, sitting approximately a foot and a half away from it. There are no software updates available for Snow Leopard (10.6.3). I have a bluetooth keyboard (that sits a little closer to the macbook, though I'm not sure this is the issue) that rarely suffers from this problem. Google results mostly suggest to update the software but I have the most updated version of it already. Does anybody have any idea what could be causing the issue? Is this simply a defective mouse? Additional info: I tried replacing the batteries with new ones, making sure they are sitting tightly in their position with no change in behavior (still disconnects periodically). Also, this doesn't seem to be a problem that the mouse is turning itself off to save battery - it does not reconnect when I move or click it. If I wait long enough (a couple of minutes) it reconnects on its own. Otherwise I have to go to the bluetooth menu with my macbook touchpad and choose "yuval's mouse - Connect"

  Read the article

• Unable to copy files previously extracted from archives created on a Mac, even after claiming ownership

  - by Maxim Zaslavsky

  I reinstalled Windows on my computer today, and backed up my music to a USB drive. Now, I'm trying to copy the files onto my fresh Windows partition, but I'm unable to copy files that I obtained within my previous Windows installation from zip archives created on Macs. When I try to copy those previously-extracted files, I get an error saying that I need permission from S-1-5-21-...-1000 (a bizarre long ID). The first thing I tried was to take ownership of the files by setting my new user account as the owner, but that resulted in errors saying that I need permission from myself! Some Googling suggested adding antivirus suggestions, so I excluded the relevant folders from Microsoft Security Essentials, but the issue persists. For what it's worth, it seems that some program (so far I've only installed Chrome, Microsoft Security Essentials, and the latest Windows updates) created an empty folder named 601c8c7f0e0c03f725 at the root of my external USB hard drive. What gives?

  Read the article

• Syn_Recievd on port 80 , IIS 7.5

  - by Ashian

  Hi I have a trouble on my windows 2008 server. I host several web site on it. From some days ago, my web sites stop responding on port 80 after a while. In this time I can't access web sites from local machine and from remote. I can also browse websites on other ports ( custom port that I set) I find that I have many Syn_Received status on netstat. And when web sites stop, I got only syn_received on port 80. I have to restart server because when I try to restart IIS , it takes a long time to stop W3SVC and many times it doesn’t stop at all. Would anyone please tell me : - How can I manage Syn Attack ? Thanks

  Read the article

• How to fix AVI index error

  - by Tim

  I try to open an AVI file. The first software I tried is VLC media player. It reports some error about AVI index: This AVI file is broken. Seeking will not work correctly. Do you want to try to fix it? This might take a long time. I chose yes, and it began fixing AVI index and existed when the repair progress bar reaches 20% or so. Then the video started playing and stopped much earlier than when it is supposed to finish. Next I tried to open it in Totem Movie Player, which also stopped earlier at the same place as in VLC player. I tried to play it in GMplayer. Now the entire AVI file can be played from start to finish, but it is impossible to drag playing progress bar while it was possible in VLC player and Totem player. I heard that Avidemux can fix AVI index error, but later discovered it failed to open the AVI file. So I was wondering how I can fix the AVI index error, or at least drag the playing progress bar in GMplayer? Thanks and regards!

  Read the article

• Database Connectivity Test with UDL File

  - by Ben Griswold

  I bounced around between projects a lot last week.  What each project had in common was the need to validate at least one SQL connection.  Whether you have SQL tools like SSMS installed or not, this is a very easy task if you are aware of the UDL (Universal Data Link) files.  Create a new file and name it anything as long as it has the .udl extension. Open the file, choose a provider: Click Next >> or navigate to the Connection Tab to provide connection information.  Once you provide server and login credentials, the database list will populate.  At this point, you know the connection is valid. but go ahead and click the Test Connection button anyway. On the final tab, you can provide extra connection information like Application Name which can come in handy.  The All tab is beneficial if you want to build a valid connection string to include in your own applications.  If you save the file and then open in Notepad, you’ll find that said connection string: Provider=SQLOLEDB.1;Integrated Security=SSPI;Persist Security Info=False;Initial Catalog=master;Data Source=(local);Application Name=TestApp I hope this tip helps save you some time.  How do you test if you don’t have SSMS installed?

  Read the article

• Prevent Windows Live Mail to download all messages from IMAP

  - by m8t

  Hello, Recently I'm trying the Window Live Mail client. Simple and beautiful. I have set up an IMAP account, and I'm used that a client only downloads headers. However Windows Live Mail automatically creates a list of tasks to download all messages from all directories when you are closing the client. Is it possible to avoid this? It's a good and a bad thing. You can work offline and you have a backup, but it takes extremely long to perform, in fact I have about hundred of thousand of emails. This task can take a whole day to perform. After looking in the settings I don't see anything special, maybe you have an idea? Thank you Mike

  Read the article

• More than 3 seconds "Initial Connection" time (webpagetest.org)

  - by George Tasioulis

  I'm having a weird issue with a vBulletin forum, on a 2? Xeon E5645 w/ 16GB RAM, cPanel and LiteSpeed webserver; It takes too long to start loading... When I tested it with webpagetest.org I saw that for every request there's a 3 second "Initial connection" delay, which I don't know why is happening. Here's a screenshot: CPU Load is between 0.03 and 0.05, I've got several GB of free RAM, practical no I/O activity, and this delay can occur even with only one visitor on the forum. Where do you suggest I start searching? What could be the reason for this kind of delay? I don't think it's the webserver, or the forum because there's another website on the server (total 2 sites) which is WordPress based, and has exactly the same issue with the 3 second initial connection delay. I believe it's OS related, but need a clue on where to start looking. Thanks in advance :)

  Read the article

• Should I install an AV product on my domain controller?

  - by mhud

  Should I run a server-specific antivirus, regular antivirus, or no antivirus at all on my servers, particularly my Domain Controllers? Here's some background about why I'm asking this question: I've never questioned that antivirus software should be running on all windows machines, period. Lately I've had some obscure Active Directory related issues that I have tracked down to antivirus software running on our domain controllers. The specific issue was that Symantec Endpoint Protection was running on all domain controllers. Occasionally, our Exchange server triggered a false-positive in Symantec's "Network Threat Protection" on each DC in sequence. After exhausting access to all DCs, Exchange began refusing requests, presumably because it could not communicate with any Global Catalog servers or perform any authentication. Outages would last about ten minutes at a time, and would occur once every few days. It took a long time to isolate the problem because it was not easily reproducible and generally investigation was done after the issue resolved itself.

  Read the article

• “Big Data” Is A Small Concept Unless You Can Apply It To The Customer Experience

  - by Michael Hylton

  There’s been a lot of recent talk in the industry about “big data”.  Much can be said about the importance of big data and the results from it, but you need to always consider the customer experience when analyzing and applying customer data. Personalization and merchandising drive the user experience.  Big data should enable you to gain valuable insight into each of your customers and apply that insight at the moment they are on your Web site, talking to one of your call center agents, or any other touchpoint.  While past customer experience is important, you need to combine that with what your customer is doing on your Web site now as well what they are doing and saying on social networking sites.  It’s key to have a 360 degree view of your customer across all of your touchpoints in order to provide that relevant and consistent experience that they come to expect when interacting with your brand. Big data can enable you to effectively market, merchandize, and recommend the right products to the right customers and the right time.  By taking customer data and applying it to product recommendations, you have an opportunity to gain a greater share of wallet through the cross-selling and up-selling of additional products and services.  You can also build sustaining loyalty programs to continue to engage with your customers throughout their long-term relationship with your brand.

  Read the article

• “Big Data” Is A Small Concept Unless You Can Apply It To The Customer Experience

  - by Michael Hylton

  There’s been a lot of recent talk in the industry about “big data”.  Much can be said about the importance of big data and the results from it, but you need to always consider the customer experience when analyzing and applying customer data. Personalization and merchandising drive the user experience.  Big data should enable you to gain valuable insight into each of your customers and apply that insight at the moment they are on your Web site, talking to one of your call center agents, or any other touchpoint.  While past customer experience is important, you need to combine that with what your customer is doing on your Web site now as well what they are doing and saying on social networking sites.  It’s key to have a 360 degree view of your customer across all of your touchpoints in order to provide that relevant and consistent experience that they come to expect when interacting with your brand. Big data can enable you to effectively market, merchandize, and recommend the right products to the right customers and the right time.  By taking customer data and applying it to product recommendations, you have an opportunity to gain a greater share of wallet through the cross-selling and up-selling of additional products and services.  You can also build sustaining loyalty programs to continue to engage with your customers throughout their long-term relationship with your brand.

  Read the article

• Is there any desktop version available for wsywyg editors

  - by user825904

  I have been searching for long and i am not able to find one editor which i can always keep open for daily notes keeping with some codes and which highlights the code Just like we have our editor where we ask questions. ALl is want is I can write some text as normal Then i have few php code which i can write and then click some code button or like we have ctrl +K and i gets higlighted then on the same page i write some paragraph text as normal withoout higligting and some bullet points Then again i get some c++ code and i wrap that around on the same page and page grows daily Currently i use notepad++ and it does not support syntx higlighting of different langages on same page and on individual blocks. it highights all the file even the normal text as well basically i am looking wsywyg editor but as windows desktop application

  Read the article

• How to solve Microsoft Office error 1402 on Windows 7?

  - by yihang

  I have installed Microsoft Office on my new Windows 7 64-bit system. Recently, it encounter some error and I tried to re-install it. It wasn't successful. So, I have to use Microsoft Install Clean Up to uninstall Microsoft Office. When I tried to install it again, I received this message: Microsoft Office 2007 encountered an error during setup. Error 1402. Setup cannot open the registry key. {a bunch of long keys}. Verify that you have sufficient permissions to access the registry or contact Microsoft Product Support Service for assistance. For information about how to contact PSS, see {a *chm file}. After that, I tried to run the setup as administrator but I ended up with the same error. So what should I do to solve this problem?

  Read the article

• Squid 3 reloading makes it stop serving requests

  - by coredump

  So, we use Squid 3 here (3.0.STABLE8-3+lenny4), pretty standard configuration (no dansguardian or similar) + NTLM authentication with LDAP background, circa 1000 users on a busy day, and our acls reference some external files (allowed/blocked sites/ip addresses). On Squid 2.X we used to be capable of reloading it's configuration (to add or sites or addresses to rules, etc) and squid would not stop serving during the reload. Since we changed to 3.0, that seems to be impossible: everytime we use reload (or -k reconfigure) it stop serving requests for as long as 2 minutes, and clients receive a Configured proxy is not accepting connections message. I checked the documentation and got nothing about it, does anyone else suffer from this problem or is it a isolated case on my setup? Also, if you have Squid 3.0 and doesn't suffer from this problem, how is your squid configured?

  Read the article

• Unable to enter ubuntu after reboot PC; showing black screen with lots of weire words

  - by Phoenix Wei

  I use Wubi to install Ubuntu 12.04 on my Windows 7 system. My PC is Acer Aspire S5-391 with a 64-bit operating system. After I finish installing Wubi on Windows I reboot my PC as told by the instruction. Then I got a black screen with the following words shown: [[BGave up waiting for root device. Common Problems: -Boot args (cat/proc/cmdline) -Check rootdelay=(did the system wait long enough?) -check root=(did the system wait for the right device?) -Missing modules(cat/proc/modules; ls/dev) ALERT! /dev/disk/by-uuid/928E20128E1FEE0B does not exist. Dropping to a shell! BusyBox v1.18.5(ubuntu 1:1.18.5-1ubuntu4)built-in shell (ash) Enter 'help' for a list of built-in commands. (intramfs) _ I don't know how to deal with this but force my PC to shut down. I can still successfully enter Windows. But everytime I try to enter unbuntu, it shows the above words.......

  Read the article

• Cross-Platform Mobile Development With Mono for Android and MonoTouch

  - by Wallym

  Many years ago, in fact pre-Java, I remember a hallway discussion about the desire to write a single application that could easily run across various platforms. At the time, we were only worried about writing applications on Windows 3.1 and Mac OS 7.x. There were many discussions about windows, user interface concepts, and specifically a rather long discussion as to whether Mac users would accept a Mac application that didn't have balloon help. Thankfully, the marketplace answered this question for us with the Windows API winning the battle.A similar set of questions is currently going on in the mobile world. Unfortunately, at this point in time, there is currently no winning API and none currently in sight. What's a developer to do? Here are some questions that developers have (and there are many more):How can mobile developers target Android and the iPhone with the same code?How can .NET developers share their code across Android, iPhone and other platforms?How can developers give applications the look and feel of the specific platform and still allow as much code as possible to be shared?Mobile devices share many common features, such as cameras, accelerometers, and address books. How can we take advantage of them in a platform independent way and still give the users the look of every other application running on their platform?In this article, we'll look at some solutions to these cross-platform and code-sharing questions between Mono for Android, MonoTouch and the .NET Framework available to developers. 

  Read the article

• Google Introduces Android Gingerbread and Nexus S Phone

  - by Gopinath

  Google today officially announced the availability of next version of Android(version 2.3) nicknamed “Gingerbread”. This is a long awaited upgrade to it’s smartphone platform from Google and below are the highlights of new features: Rich multimedia – including support for VP8 and WebM video and new audio effects. Support for front-facing cameras, SIP/VoIP and Near Field Communication (NFC). Enhancements for game developers, including new sensor types. You can read more about the release at Google blog post and watch this embedded video. Samsung Nexus S – The First Gingerbread Android Phone Samsung’s Nexus S is the first Android phone to be released with Gingerbread operation system. This is a phone that was designed with direct inputs from Google team and comes with a clean install of Android OS – no additional software layers from third party OEMs or carriers. Visit Nexus S site for more details This article titled,Google Introduces Android Gingerbread and Nexus S Phone, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

  Read the article

• hp pavilion g6 1250 wireless problems

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation , ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) there are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• IBM Tivoli Network Manager IP Edition - Job does not run

  - by Thorsten Niehues

  Since our network discovery takes too long I tried to split the biggest job into two parts. The two parts use the same Perl script but have a different scope. I copied a Job (Agent) doing the following: Copied the .agnt file Copied the associated perl script The problem is that one or the other job (changes randomly) does not run. The Disco Process will fail eventually. In the log of the job which does not run I see the following error message: Wed Jul 18 08:48:54 2012 Warning: Failed to send on transport layer found in file CRivObjSockClient.cc at line 1293 - Client My_MacTable_Cis is not connected to service Helper How do I fix this problem?

  Read the article

• Need to store and backup HD vid files. But need to access them alot.

  - by Mike

  I've had my 700 Gb HDD ever since I bought my computer so partitioning it is out of the question. What I need is a place to keep my HD vid files so when I edit, I don't get a long load time in the editing software. But I also need to keep a back-up of all my other important files which I haven't been doing. Should I buy an additional internal drive JUST for vid files and buy an external for backup of all my files? What are my best options?

  Read the article

• MySQL 5.1.49 freezing every two days

  - by maximus

  Hi all, our mysql system is "freezing" every two days. By "freezing" i mean the following: it doesn't respond to ping we can't login with SSH we don't get any answer from MySQL there is no entry in the error logs! neither from linux neither from MySQL. we have already changed to a completely new hardware, we have the same problem, so it's definitely not a hardware problem. we do not have any other software installed except a firewall (iptables rule) we can restart the server from another server using rsyslog (www.rsyslog.com)(software reset) Could someone help me, by giving me some pointers what could i do to figure out the problem? I have included every detail about our settings. Thank you in advance for your help. Max. Our system parameters and settings: System-Memory: 12GB Processor: Intel 7-920 Quadcore Operating system: Debian 5 (lenny) 64bit MySQL 5.1.49 Databases: (a) a small phpbb forum (b) a 6GB database 3 tables with about 15 million rows my.cnf # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = our-ip-address # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 256K thread_cache_size = 32 max_connections = 300 table_cache = 2048 #thread_concurrency = 4 # Used for InnoDB tables recommended to 50%-80% available memory innodb_buffer_pool_size = 6G # 20MB sometimes larger innodb_additional_mem_pool_size = 20M # 8M-16M is good for most situations innodb_log_buffer_size = 8M # Disable XA support because we do not use it innodb-support-xa = 0 # 1 is default wich is 100% secure but 2 offers better performance innodb_flush_log_at_trx_commit = 1 innodb_flush_method = O_DIRECT #innodb_thread_concurency = 8 # Recommended 64M - 512M depending on server size innodb_log_file_size = 512M # One file per table innodb_file_per_table # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 16M #query_cache_type = 1 #query_cache_min_res_unit= 2K #join_buffer_size = 1M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog. This is a Debian improvement :) # # Here you can see queries with especially long duration log_slow_queries = /var/log/mysql/mysql-slow.log long_query_time = 2 log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. #server-id = 1 log_bin = /var/log/mysql/mysql-bin.log # WARNING: Using expire_logs_days without bin_log crashes the server! See README.Debian! expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # * InnoDB plugin # As of MySQL 5.1.38, the InnoDB plugin from Oracle is included in the MySQL source code. # It has many improvements and better performances than the built-in InnoDB storage engine. # Please read http://www.innodb.com/products/innodb_plugin/ for more information. # Uncommenting the two following lines to use the InnoDB plugin. ignore_builtin_innodb plugin-load=innodb=ha_innodb_plugin.so # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * NDB Cluster # # See /usr/share/doc/mysql-server-*/README.Debian for more information. # # The following configuration is read by the NDB Data Nodes (ndbd processes) # not from the NDB Management Nodes (ndb_mgmd processes). # # [MYSQL_CLUSTER] # ndb-connectstring=127.0.0.1 # # * IMPORTANT: Additional settings that can override those from this file! # !includedir /etc/mysql/conf.d/ UPDATE After installing sysstat and configuring it to collect data after every minute i have the following datas. I used sar to generate the following output: The log-file is too big so coudn't enter it here but uploaded to box.net. The link is http://www.box.net/shared/xc6rh7qqob SECOND UPDATE We started a ping command in the background, and that solved the problem. Now the server does work since more then a week. We still don't know what's the problem.

  Read the article

• How do I increase my home's bandwidth?

  - by Derek

  I just mistakingly posted this on Stack Exchange but don't know how to delete it... Anyway, I was thinking of building a home server to use instead of renting a VPS, because in the long run it would be cheaper. What I'm concerned with is the bandwidth limit of my house. I know when I'm downloading something off the internet, if I download at high speeds the rest of the computers connected to my router will become slower. Is there any way to avoid this? There are other cable outlets in my house, will connecting a modem and router there avoid this problem?

  Read the article

• Git pull auto complete OSX

  - by vodkhang

  Follow some instruction on this site http://denis.tumblr.com/post/71390665/adding-bash-completion-for-git-on-mac-os-x-leopard . I can do git auto complete for MAC OS. However, when I type git pull origin ma (for master), and then tab it takes a long time for git to auto complete to become git pull origin master . I think it connect to the server to get the branch, but I am not sure, is there any way to make it faster and only get the branch on local machine cd /tmp git clone git://git.kernel.org/pub/scm/git/git.git cd git git checkout v`git --version | awk '{print $3}'` cp contrib/completion/git-completion.bash ~/.git-completion.bash cd ~ rm -rf /tmp/git echo -e "source ~/.git-completion.bash" >> .profile

  Read the article

• How to Add the Windows Calculator to the Quick Access Toolbar in Microsoft Excel 2013

  - by Lori Kaufman

  Do you use the Windows Calculator to perform quick calculations while building spreadsheets in Excel? You can save time by adding the Calculator to the Quick Access Toolbar in Excel so you don’t have to leave the program to access the Calculator. To do this, click the down arrow on the right side of the Quick Access Toolbar and select More Commands from the drop-down menu. On the Quick Access Toolbar screen on the Excel Options dialog box, select Commands Not in the Ribbon from the Choose commands from drop-down list. Scroll down in the long list and select Calculator. Click Add to add the Calculator to the Quick Access Toolbar. Click OK to accept the change and close the Excel Options dialog box. You’ll see a Calculator icon on the Quick Access Toolbar. When you move your mouse over the icon, a hint displays saying “Custom.” Despite the label, when you click the icon, the Windows Calculator opens. The same procedure works for adding the Windows Calculator to Excel 2010, as well.     

  Read the article

< Previous Page | 359 360 361 362 363 364 365 366 367 368 369 370  | Next Page >