boot repair - Page 364 - Developer IT

2 drives, slow software RAID1 (md)

- by bart613

Hello, I've got a server from hetzner.de (EQ4) with 2* SAMSUNG HD753LJ drives (750G 32MB cache). OS is CentOS 5 (x86_64). Drives are combined together into two RAID1 partitions: /dev/md0 which is 512MB big and has only /boot partitions /dev/md1 which is over 700GB big and is one big LVM which hosts other partitions Now, I've been running some benchmarks and it seems like even though exactly the same drives, speed differs a bit on each of them. # hdparm -tT /dev/sda /dev/sda: Timing cached reads: 25612 MB in 1.99 seconds = 12860.70 MB/sec Timing buffered disk reads: 352 MB in 3.01 seconds = 116.80 MB/sec # hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 25524 MB in 1.99 seconds = 12815.99 MB/sec Timing buffered disk reads: 342 MB in 3.01 seconds = 113.64 MB/sec Also, when I run eg. pgbench which is stressing IO quite heavily, I can see following from iostat output: Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 231.40 0.00 298.00 0.00 9683.20 32.49 0.17 0.58 0.34 10.24 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 231.40 0.00 298.00 0.00 9683.20 32.49 0.17 0.58 0.34 10.24 sdb 0.00 231.40 0.00 301.80 0.00 9740.80 32.28 14.19 51.17 3.10 93.68 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 231.40 0.00 301.80 0.00 9740.80 32.28 14.19 51.17 3.10 93.68 md1 0.00 0.00 0.00 529.60 0.00 9692.80 18.30 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.60 0.00 4.80 8.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 529.00 0.00 9688.00 18.31 24.51 49.91 1.81 95.92 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 152.40 0.00 330.60 0.00 5176.00 15.66 0.19 0.57 0.19 6.24 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 152.40 0.00 330.60 0.00 5176.00 15.66 0.19 0.57 0.19 6.24 sdb 0.00 152.40 0.00 326.20 0.00 5118.40 15.69 19.96 55.36 3.01 98.16 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 152.40 0.00 326.20 0.00 5118.40 15.69 19.96 55.36 3.01 98.16 md1 0.00 0.00 0.00 482.80 0.00 5166.40 10.70 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 482.80 0.00 5166.40 10.70 30.19 56.92 2.05 99.04 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 181.64 0.00 324.55 0.00 5445.11 16.78 0.15 0.45 0.21 6.87 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 181.64 0.00 324.55 0.00 5445.11 16.78 0.15 0.45 0.21 6.87 sdb 0.00 181.84 0.00 328.54 0.00 5493.01 16.72 18.34 61.57 3.01 99.00 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 181.84 0.00 328.54 0.00 5493.01 16.72 18.34 61.57 3.01 99.00 md1 0.00 0.00 0.00 506.39 0.00 5477.05 10.82 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 506.39 0.00 5477.05 10.82 28.77 62.15 1.96 99.00 And this is completely getting me confused. How come two exactly the same specced drives have such a difference in write speed (see util%)? I haven't really paid attention to those speeds before, so perhaps that something normal -- if someone could confirm I would be really grateful. Otherwise, if someone have seen such behavior again or knows what is causing such behavior I would really appreciate answer. I'll also add that both "smartctl -a" and "hdparm -I" output are exactly the same and are not indicating any hardware problems. The slower drive was changed already two times (to new ones). Also I asked to change the drives with places, and then sda were slower and sdb quicker (so the slow one was the same drive). SATA cables were changed two times already.

Read the article

How to restore Linode to Vagrant VM?

- by Iain Elder

I'm trying to set up a Linux development environment so I can safely make changes to my website without breaking the live site. Linode hosts my live site. A simple solution would be to host my development server on Linode as well, but I want to avoid doubling my hosting costs. The cheapest way I see is to use Vagrant on my Windows workstation to host my development environment. After I attempt to restore the backup to Vagrant and reboot the VM, I can no longer ssh into the Vagrant host. It's probably because by restoring the backup I overwrite some special Vagrant configuration, but I'm not sure how to avoid that. How do I make this approach work? If my approach is fundamentally wrong, can you suggest an alternative? Creating the backup On the Linode I used these commands to create a compressed copy of the entire filesystem, while ignoring things that shouldn't be included in the backup: $ sudo rsync -ahvz --exclude={/dev/*,/proc/*,/sys/*,/tmp/*,/run/*,/mnt/*,/backup/*} /* /backup/2 $ sudo tar -czf /backup/2.gz /backup/2 The backup file is called 2.gz because this is thesecond backup. The first backup is called 1.gz. I use WinSCP to copy the backup file to my Windows workstation. Setting up the Vagrant host I need a Vagrant box that matches my Linode operating system (Ubuntu 12.04.3 LTS, kernel 3.9.3). I selected the closet match from vagrantbox.es: Ubuntu Server Precise 12.04.3 amd64 Kernel is ready for Docker (Docker not included) On my workstation I ran these commands to add the box and initialize and boot an instance: $ vagrant box add ubuntu-precise http://nitron-vagrant.s3-website-us-east-1.amazonaws.com/vagrant_ubuntu_12.04.3_amd64_virtualbox.box $ mkdir linode-test $ cd linode-test $ vagrant init ubuntu-precise $ vagrant up Now Vagrant is running a machine with SSH on port 2222. The operating system version is the same. The kernel version is 3.8.0. Sounds close enough. Restoring the backup With WinSCP I copied the backup file 2.gz to /home/vagrant/2.gz on the Vagrant box. With PuTTY I connected via ssh to my new Vagrant box: On the box move the backup to the filesystem root. $ sudo mv 2.gz / Extract the archive to the filesystem root: $ sudo tar -xvpz -f 2.gz -C / --strip-components=2 (I discovered I need to use strip components because all files in the archive have the prefix backup/2/. I'll fix this for the next backup.) After the tar command completes, I log out of the box. Testing the backup When I try to log in again, it doesn't let me log in as vagrant with a password any more. It does let me log in as iain, my user on the live Linode, with a password. That surprised me because I disabled password authentication on my live Linode. I figured that I have to restart the ssh service for the change to take effect. Instead of restarting just ssh, I chose to restart the whole system. Now I can't even get to the login screen. PuTTY says "connection refused" when I try to connect. What went wrong?

Read the article

Dual head setup for Ubuntu 10.04.1 and Windows XP Pro with same hardware configuration

- by mejpark

I have a Dell OptiPlex 360 workstation at work, with 2 x ATI RV280 [Radeon 9200 PRO] graphics cards installed, which are attached to two identical 19" HII flat panel monitors. I'm using the open source Radeon driver with Ubuntu, and the proprietary drivers with Windows. The good news is that dual head configuration works for both OSes. The bad news is, I have to use a different hardware configuration for each OS to achieve this. Hardware config #1: Dual monitors work for Windows XP Pro like this: First display -> external VGA port Second display -> DVI input on gfx card Hardware config #2: Dual monitors work for Ubuntu 10.04.1 like this: First display -> VGA port on gfx card Second display -> DVI input on gfx card I connected up the displays according to Config #2 and booted up Windows, which resulted in a mirror image on both screens. I was unable to login, as the login box was not visible. I unplugged the VGA lead from gfx card and plugged it into the external VGA port (Config #1) - Windows dual head works again, but the VGA-connected screen is not recognised by Ubuntu and remains in standby mode. Is it possible to configure a dual head setup for Ubuntu using Config #1, or am I missing something? I tried setting up dual monitors using Config #1, this morning which didn't work. By default, there is no xorg.conf file in Ubuntu 10.04.1, so I generated one using: $ sudo X :2 -configure X.Org X Server 1.7.6 Release Date: 2010-03-17 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-27-server i686 Ubuntu Current Operating System: Linux harrier 2.6.32-24-generic #42-Ubuntu SMP Fri Aug 20 14:24:04 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-24-generic root=UUID=a34c1931-98d4-4a34-880c-c227a2936c4a ro quiet splash Build Date: 21 July 2010 12:47:34PM xorg-server 2:1.7.6-2ubuntu7.3 (For technical support please see http://www.ubuntu.com/support) Current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.2.log", Time: Mon Sep 13 10:02:02 2010 List of video drivers: apm ark intel mach64 s3virge trident mga tseng ati nouveau neomagic i740 openchrome voodoo s3 i128 radeon siliconmotion nv ztv vmware v4l chips rendition savage sisusb tdfx geode sis r128 cirrus fbdev vesa (++) Using config file: "/home/michael/xorg.conf.new" (==) Using config directory: "/usr/lib/X11/xorg.conf.d" (II) [KMS] No DRICreatePCIBusID symbol, no kernel modesetting. Xorg detected your mouse at device /dev/input/mice. Please check your config if the mouse is still not operational, as by default Xorg tries to autodetect the protocol. Xorg has configured a multihead system, please check your config. Your xorg.conf file is /home/michael/xorg.conf.new To test the server, run 'X -config /home/michael/xorg.conf.new' ddxSigGiveUp: Closing log $ sudo X -config /home/michael/xorg.conf.new Fatal server error: Server is already active for display 0 If this server is no longer running, remove /tmp/.X0-lock and start again. Please consult the The X.Org Foundation support at http://wiki.x.org for help. ddxSigGiveUp: Closing log I then booted Ubuntu in failsafe mode, dropped into root shell, and executed $ X -config /home/michael/xorg.conf.new again. The screen went blank and turned off, so

Read the article

Performance issues when using SSD for a developer notebook (WAMP/LAMP stack)?

- by András Szepesházi

I'm a web application developer using my notebook as a standalone development environment (WAMP stack). I just switched from a Core2-duo Vista 32 bit notebook with 2Gb RAM and SATA HDD, to an i5-2520M Win7 64 bit with 4Gb RAM and 128 GB SDD (Corsair P3 128). My initial experience was what I expected, fast boot, quick load of all the applications (Eclipse takes now 5 seconds as opposed to 30s on my old notebook), overall great experience. Then I started to build up my development stack, both as LAMP (using VirtualBox with a debian guest) and WAMP (windows native apache + mysql + php). I wanted to compare those two. This still all worked great out, then I started to pull in my projects to these stacks. And here came the nasty surprise, one of those projects produced a lot worse response times than on my old notebook (that was true for both the VirtualBox and WAMP stack). Apache, php and mysql configurations were practically identical in all environments. I started to do a lot of benchmarking and profiling, and here is what I've found: All general benchmarks (Performance Test 7.0, HDTune Pro, wPrime2 and some more) gave a big advantage to the new notebook. Nothing surprising here. Disc specific tests showed that read/write operations peaked around 380M/160M for the SSD, and all the different sized block operations also performed very well. Started apache performance benchmarking with Apache Benchmark for a small static html file (10 concurrent threads, 500 iterations). Old notebook: min 47ms, median 111ms, max 156ms New WAMP stack: min 71ms, median 135ms, max 296ms New LAMP stack (in VirtualBox): min 6ms, median 46ms, max 175ms Right here I don't get why the native WAMP stack performed so bad, but at least the LAMP environment brought the expected speed. Apache performance measurement for non-cached php content. The php runs a loop of 1000 and generates sha1(uniqid()) inisde. Again, 10 concurrent threads, 500 iterations were used for the benchmark. Old notebook: min 0ms, median 39ms, max 218ms New WAMP stack: min 20ms, median 61ms, max 186ms New LAMP stack (in VirtualBox): min 124ms, median 704ms, max 2463ms What the hell? The new LAMP performed miserably, and even the new native WAMP was outperformed by the old notebook. php + mysql test. The test consists of connecting to a database and reading a single record form a table using INNER JOIN on 3 more (indexed) tables, repeated 100 times within a loop. Databases were identical. 10 concurrent threads, 100 iterations were used for the benchmark. Old notebook: min 1201ms, median 1734ms, max 3728ms New WAMP stack: min 367ms, median 675ms, max 1893ms New LAMP stack (in VirtualBox): min 1410ms, median 3659ms, max 5045ms And the same test with concurrency set to 1 (instead of 10): Old notebook: min 1201ms, median 1261ms, max 1357ms New WAMP stack: min 399ms, median 483ms, max 539ms New LAMP stack (in VirtualBox): min 285ms, median 348ms, max 444ms Strictly for my purposes, as I'm using a self contained development environment (= low concurrency) I could be satisfied with the second test's result. Though I have no idea why the VirtualBox environment performed so bad with higher concurrency. Finally I performed a test of including many php files. The application that I mentioned at the beginning, the one that was performing so bad, has a heavy bootstrap, loads hundreds of small library and configuration files while initializing. So this test does nothing else just includes about 100 files. Concurrency set to 1, 100 iterations: Old notebook: min 140ms, median 168ms, max 406ms New WAMP stack: min 434ms, median 488ms, max 604ms New LAMP stack (in VirtualBox): min 413ms, median 1040ms, max 1921ms Even if I consider that VirtualBox reached those files via shared folders, and that slows things down a bit, I still don't see how could the old notebook outperform so heavily both new configurations. And I think this is the real root of the slow performance, as the application uses even more includes, and the whole bootstrap will occur several times within a page request (for each ajax call, for example). To sum it up, here I am with a brand new high-performance notebook that loads the same page in 20 seconds, that my old notebook can do in 5-7 seconds. Needless to say, I'm not a very happy person right now. Why do you think I experience these poor performance values? What are my options to remedy this situation?

Read the article

Can't sync filesystem without reboot

- by Fabio

I'm having an issue with a linux server. Once a week the running mysql instance hangs and there is no way to fully stop it. If I kill it, it remains in zombie status and init does not reap its pid. The server is used for staging deployments and some internal tools, so it's not under heavy load. The only process constantly used id mysql and for this I think that it's the only process which suffer of this issue. I've searched system logs for errors and the only thing I found is this error (repeated a couple of times) in dmesg output: [706560.640085] INFO: task mysqld:31965 blocked for more than 120 seconds. [706560.640198] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [706560.640312] mysqld D ffff88032fd93f40 0 31965 1 0x00000000 [706560.640317] ffff880242a27d18 0000000000000086 ffff88031a50dd00 ffff880242a27fd8 [706560.640321] ffff880242a27fd8 ffff880242a27fd8 ffff88031e549740 ffff88031a50dd00 [706560.640325] ffff88031a50dd00 ffff88032fd947f8 0000000000000002 ffffffff8112f250 [706560.640328] Call Trace: [706560.640338] [<ffffffff8112f250>] ? __lock_page+0x70/0x70 [706560.640344] [<ffffffff816cb1b9>] schedule+0x29/0x70 [706560.640347] [<ffffffff816cb28f>] io_schedule+0x8f/0xd0 [706560.640350] [<ffffffff8112f25e>] sleep_on_page+0xe/0x20 [706560.640353] [<ffffffff816c9900>] __wait_on_bit+0x60/0x90 [706560.640356] [<ffffffff8112f390>] wait_on_page_bit+0x80/0x90 [706560.640360] [<ffffffff8107dce0>] ? autoremove_wake_function+0x40/0x40 [706560.640363] [<ffffffff8112f891>] filemap_fdatawait_range+0x101/0x190 [706560.640366] [<ffffffff81130975>] filemap_write_and_wait_range+0x65/0x70 [706560.640371] [<ffffffff8122e441>] ext4_sync_file+0x71/0x320 [706560.640376] [<ffffffff811c3e6d>] do_fsync+0x5d/0x90 [706560.640379] [<ffffffff811c40d0>] sys_fsync+0x10/0x20 [706560.640383] [<ffffffff816d495d>] system_call_fastpath+0x1a/0x1f When this happens the only way to make everything working again is a full reboot, but in order to do that I'm forced to use this command after I've manually stopped all running processes echo b > /proc/sysrq-trigger otherwise normal reboot process hangs forever. I've tracked reboots script and I've found out that also the reboot process hangs on a sync call, this one in /etc/init.d/sendsigs (I'm on ubuntu) # Flush the kernel I/O buffer before we start to kill # processes, to make sure the IO of already stopped services to # not slow down the remaining processes to a point where they # are accidentily killed with SIGKILL because they did not # manage to shut down in time. sync I'm almost sure that the cause of this is an hardware issue (the RAID controller???) also because I've other two machines with the same hardware and software configuration and they don't suffer of this, but I can't find any hint in syslog or dmesg. I've also installed smartmontools and mcelog packages but none of them did report any issue. What can I do to track the cause of this issue? Today is happened again, here is the status of system after triggering a reboot init---console-kit-dae---64*[{console-kit-dae}] +-dbus-daemon +-mcelog +-mysqld---{mysqld} +-newrelic-daemon---newrelic-daemon---11*[{newrelic-daemon}] +-ntpd +-polkitd---{polkitd} +-python3 +-rpc.idmapd +-rpc.statd +-rpcbind +-sh---rc---S20sendsigs---sync +-smartd +-snmpd +-sshd---sshd---zsh---sudo---zsh---pstree +-sshd---sshd---zsh---sudo---zsh And here is the status of sync process # ps aux | grep sync root 3637 0.1 0.0 4352 372 ? D 05:53 0:00 sync i.e. Uninterruptible sleep... Hardware specs as reported by lshw I think the raid controller is a fake raid. I usually don't deal with hardware (and for the record I don't have physical access to it) description: Computer product: X7DBP () vendor: Supermicro version: 0123456789 serial: 0123456789 width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=normal frontpanel_password=unknown keyboard_password=unknown power-on_password=disabled uuid=53D19F64-D663-A017-8922-0030487C1FEE *-core description: Motherboard product: X7DBP vendor: Supermicro physical id: 0 version: PCB Version serial: 0123456789 *-firmware description: BIOS vendor: Phoenix Technologies LTD physical id: 0 version: 6.00 date: 05/29/2007 size: 106KiB capacity: 960KiB capabilities: pci pnp upgrade shadowing escd cdboot bootselect edd int13floppy2880 acpi usb ls120boot zipboot biosbootspecification *-storage description: RAID bus controller product: 631xESB/632xESB SATA RAID Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 09 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list configuration: driver=ahci latency=0 resources: irq:19 ioport:18a0(size=8) ioport:1874(size=4) ioport:1878(size=8) ioport:1870(size=4) ioport:1880(size=32) memory:d8500400-d85007ff

Read the article

FreeBSD with Vagrant - don't know how to check guest additions version

- by joelmaranhao

On Mac OS X 10.9.3 Picked a box from the VagrantCloud Init the vagrant box $ vagrant init chef/freebsd-9.2-i386 A `Vagrantfile` has been placed in this directory. You are now ready to `vagrant up` your first virtual environment! Please read the comments in the Vagrantfile as well as documentation on `vagrantup.com` for more information on using Vagrant. List the files $ ls -al -rw-r--r-- 1 joel staff 4831 Jun 5 17:17 Vagrantfile Vagrantfile content VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| config.vm.box = "chef/freebsd-9.2-i386" end Starting my virtual box leads to Errors $ vagrant up Bringing machine 'default' up with 'virtualbox' provider... ==> default: Box 'chef/freebsd-9.2-i386' could not be found. Attempting to find and install... default: Box Provider: virtualbox default: Box Version: >= 0 ==> default: Loading metadata for box 'chef/freebsd-9.2-i386' default: URL: https://vagrantcloud.com/chef/freebsd-9.2-i386 ==> default: Adding box 'chef/freebsd-9.2-i386' (v1.0.0) for provider: virtualbox default: Downloading: https://vagrantcloud.com/chef/freebsd-9.2-i386/version/1/provider/virtualbox.box ==> default: Successfully added box 'chef/freebsd-9.2-i386' (v1.0.0) for 'virtualbox'! ==> default: Importing base box 'chef/freebsd-9.2-i386'... ==> default: Matching MAC address for NAT networking... ==> default: Checking if box 'chef/freebsd-9.2-i386' is up to date... ==> default: Setting the name of the VM: freebsd92-i386_default_1401982167145_49633 ==> default: Fixed port collision for 22 => 2222. Now on port 2201. ==> default: Clearing any previously set network interfaces... ==> default: Preparing network interfaces based on configuration... default: Adapter 1: nat ==> default: Forwarding ports... default: 22 => 2201 (adapter 1) ==> default: Booting VM... ==> default: Waiting for machine to boot. This may take a few minutes... default: SSH address: 127.0.0.1:2201 default: SSH username: vagrant default: SSH auth method: private key default: Warning: Connection timeout. Retrying... default: Warning: Connection timeout. Retrying... ==> default: Machine booted and ready! Sorry, don't know how to check guest version of Virtualbox Guest Additions on this platform. Stopping installation. ==> default: Checking for guest additions in VM... default: The guest additions on this VM do not match the installed version of default: VirtualBox! In most cases this is fine, but in rare cases it can default: prevent things such as shared folders from working properly. If you see default: shared folder errors, please make sure the guest additions within the default: virtual machine match the version of VirtualBox you have installed on default: your host and reload your VM. default: default: Guest Additions Version: 4.2.16 default: VirtualBox Version: 4.3 ==> default: Mounting shared folders... default: /vagrant => /Users/joel/Code/anybots/operations/robot/freebsd92-i386 Vagrant attempted to execute the capability 'mount_virtualbox_shared_folder' on the detect guest OS 'freebsd', but the guest doesn't support that capability. This capability is required for your configuration of Vagrant. Please either reconfigure Vagrant to avoid this capability or fix the issue by creating the capability. Note that I have recently installed the latest version of VirtualBox, but somehow I can't find the Guest Additions.

Read the article

ubuntu 10.04; kvm bridged networking not working with public ip addresses

- by senorsmile

I have a dedicated hosted server box with ubuntu 10.04 64 bit installed. I would like to run kvm with ubuntu 8.04 installed for some php 5.2 compatible apps(they don't work right with php 5.3, the default in ubuntu 10.04). I installed KVM as instructed at https://help.ubuntu.com/community/KVM/Installation . I installed the vm using virt-manager. I never could figure out how use virt-install or any of those automated installers. I just installed it using the disc. I set up bridged networking as per https://help.ubuntu.com/community/KVM/Networking . However, the bridged connection doesn't work. Here's my /etc/network/interfaces on the host, running ubuntu 10.04. (with specific public ip blanked) auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address xx.xx.xx.xx netmask 255.255.255.248 gateway xx.xx.xx.xa bridge_ports eth0 bridge_stp on bridge_fd 0 bridge_maxwait 10 ` Here's my /etc/network/interfaces on the guest, running ubuntu 8.04. auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xy netmask 255.255.255.248 gateway xx.xx.xx.xa The two vm's can communicate to each other. But, the guest vm can't access anyone in the real world. Here's my /etc/libvirt/qemu/store_804.xml <domain type='kvm'> <name>store_804</name> <uuid>27acfb75-4f90-a34c-9a0b-70a6927ae84c</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/store_804.img'/> <target dev='hda' bus='ide'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> </disk> <interface type='bridge'> <mac address='52:54:00:26:0b:c6'/> <source bridge='br0'/> <model type='virtio'/> </interface> <console type='pty'> <target port='0'/> </console> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='es1370'/> <video> <model type='cirrus' vram='9216' heads='1'/> </video> </devices> </domain> Any idea where I've gone wrong?

Read the article

Linux Kernel not passing through multicast UDP packets

- by buecking

Recently I've set up a new Ubuntu Server 10.04 and noticed my UDP server is no longer able to see any multicast data sent to the interface, even after joining the multicast group. I've got the exact same set up on two other Ubuntu 8.04.4 LTS machines and there is no problem receiving data after joining the same multicast group. The ethernet card is a Broadcom netXtreme II BCM5709 and the driver used is: b $ ethtool -i eth1 driver: bnx2 version: 2.0.2 firmware-version: 5.0.11 NCSI 2.0.5 bus-info: 0000:01:00.1 I'm using smcroute to manage my multicast registrations. b$ smcroute -d b$ smcroute -j eth1 233.37.54.71 After joining the group ip maddr shows the newly added registration. b$ ip maddr 1: lo inet 224.0.0.1 inet6 ff02::1 2: eth0 link 33:33:ff:40:c6:ad link 01:00:5e:00:00:01 link 33:33:00:00:00:01 inet 224.0.0.1 inet6 ff02::1:ff40:c6ad inet6 ff02::1 3: eth1 link 01:00:5e:25:36:47 link 01:00:5e:25:36:3e link 01:00:5e:25:36:3d link 33:33:ff:40:c6:af link 01:00:5e:00:00:01 link 33:33:00:00:00:01 inet 233.37.54.71 <------- McastGroup. inet 224.0.0.1 inet6 ff02::1:ff40:c6af inet6 ff02::1 So far so good, I can see that I'm receiving data for this multicast group. b$ sudo tcpdump -i eth1 -s 65534 host 233.37.54.71 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65534 bytes 09:30:09.924337 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212 09:30:09.947547 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212 09:30:10.108378 IP 192.164.1.120.58866 > 233.37.54.71.15574: UDP, length 268 09:30:10.196841 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212 ... I can also confirm that the interface is receiving mcast packets. b $ ethtool -S eth1 | grep mcast_pack rx_mcast_packets: 103998 tx_mcast_packets: 33 Now here's the problem. When I try to capture the traffic using a simple ruby UDP server I receive zero data! Here's a simple server that reads data send on port 15572 and prints the first two characters. This works on the two 8.04.4 Ubuntu Servers, but not the 10.04 server. require 'socket' s = UDPSocket.new s.bind("", 15572) 5.times do text, sender = s.recvfrom(2) puts text end If I send a UDP packet crafted in ruby to localhost, the server receives it and prints out the first two characters. So I know that the server above is working correctly. irb(main):001:0> require 'socket' => true irb(main):002:0> s = UDPSocket.new => #<UDPSocket:0x7f3ccd6615f0> irb(main):003:0> s.send("I2 XXX", 0, 'localhost', 15572) When I check the protocol statistics I see that InMcastPkts is not increasing. While on the other 8.04 servers, on the same network, received a few thousands packets in 10 seconds. b $ netstat -sgu ; sleep 10 ; netstat -sgu IcmpMsg: InType3: 11 OutType3: 11 Udp: 446 packets received 4 packets to unknown port received. 0 packet receive errors 461 packets sent UdpLite: IpExt: InMcastPkts: 4654 <--------- Same as below OutMcastPkts: 3426 InBcastPkts: 9854 InOctets: -1691733021 OutOctets: 51187936 InMcastOctets: 145207 OutMcastOctets: 109680 InBcastOctets: 1246341 IcmpMsg: InType3: 11 OutType3: 11 Udp: 446 packets received 4 packets to unknown port received. 0 packet receive errors 461 packets sent UdpLite: IpExt: InMcastPkts: 4656 <-------------- Same as above OutMcastPkts: 3427 InBcastPkts: 9854 InOctets: -1690886265 OutOctets: 51188788 InMcastOctets: 145267 OutMcastOctets: 109712 InBcastOctets: 1246341 If I try forcing the interface into promisc mode nothing changes. At this point I'm stuck. I've confirmed the kernel config has multicast enabled. Perhaps there are other config options I should be checking? b $ grep CONFIG_IP_MULTICAST /boot/config-2.6.32-23-server CONFIG_IP_MULTICAST=y Any thoughts on where to go from here?

Read the article

Application Does Not Start in Windows 7

- by Jim Fell

I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fresh from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried running sfc /scannow from the command line (with administrator privileges), shutting down the Spybot Resident, and disabling the firewall and virus scanner. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Faulting application name: SSDFresh.exe, version: 1.0.0.0, time stamp: 0x4f2a45d8 Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0xc0000005 Fault offset: 0x000007ff0016dbba Faulting process id: 0x994 Faulting application start time: 0x01cd11fd9fe978df Faulting application path: C:\Program Files (x86)\SSD Fresh\SSDFresh.exe Faulting module path: unknown Report Id: dfeed551-7df0-11e1-a2c7-002522c47ec0 Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Application: SSDFresh.exe Framework Version: v4.0.30319 Description: The process was terminated due to an unhandled exception. Exception Info: System.NullReferenceException Stack: at AbBugReporter.BugForm.InitLanguage() at AbBugReporter.BugForm..ctor(AbFlexTrans.LanguageInfo, AbBugReporter.BugReportManager, Boolean) at AbBugReporter.BugReportManager.Show(System.Exception) at SSDFresh.App.App_DispatcherUnhandledException(System.Object, System.Windows.Threading.DispatcherUnhandledExceptionEventArgs) at System.Windows.Threading.Dispatcher.CatchException(System.Exception) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(System.Object, System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.WrappedInvoke(System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.InvokeImpl(System.Windows.Threading.DispatcherPriority, System.TimeSpan, System.Delegate, System.Object, Int32) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr, Int32, IntPtr, IntPtr) at MS.Win32.UnsafeNativeMethods.DispatchMessage(System.Windows.Interop.MSG ByRef) at System.Windows.Threading.Dispatcher.PushFrameImpl(System.Windows.Threading.DispatcherFrame) at System.Windows.Application.RunInternal(System.Windows.Window) at System.Windows.Application.Run() at SSDFresh.App.Main() Error 4/2/2012 11:35:39 PM SideBySide 59 None Activation context generation failed for "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe".Error in manifest or policy file "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe.Config" on line 0. Invalid Xml syntax. Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

Read the article

Windows XP Video Configuration Issues

- by Matt

Recently I had my motherboard burn out on me. Needing the machine for work, I purchased a different motherboard and installed that. Generally a reinstall of windows is good at that point but I am not in a position to do that so I just decided I would live with it for now. When I can log-in, everything works fine, what doesn't is getting to the log-in prompt to begin with. Basically when I first installed the new mobo, every time I rebooted the machine, I would not get the windows login prompt. One of the monitors would receive a signal but the screen would be black. Moving the mouse would not show the cursor and hitting the up arrow key and typing my password and hitting enter (which will normally log you in without mouse) wouldn't change anything. I would then change the monitor configuration around (2 lcd's and a crt) and reboot and at least one of the monitors would work and display the login prompt. I could then go into display properties and turn on the other monitors. However if I rebooted again, I would get the black screen on one monitor again. I would then have to change the configuration again to one not used before and I could re-do the manual setup at that point. I think windows saves the configurations so I had to keep giving it new ones. Needless to say I've been trying to not turn off my machine. Early this week I actually got the prompt to come up without playing musical monitors. Thinking everything was getting better, I found no harm in rebooting to install the latest windows updates. Boy was I wrong. Now no matter what I do I can't get a windows log-in prompt to display. I've tried almost every conceivable combination. The new mobo has onboard video so I set that in the bios (yea bios screen always displays fine, its not until windows boots that there is a problem) to be the primary video. Still no luck. I have two other graphics cards in the machine which I'm using. Tried all kinds of configurations between those and on-board but still get this black screen of death. I read somewhere that deleting the video drivers would reset the configurations. I logged into safe mode (which works on one monitor), and uninstalled the display drivers. Still no luck and when I booted back into safe mode, it wanted to install new hardware and the display adapters weren't there as expected. Anyone have any ideas? A fresh install would be a pain and I might be getting my old board back from RMA soon so not sure I want to go through with that just yet. Only thing I can think of is to continue to try other combinations like physically removing the graphics cards. They are both EVGA 8600 cards and the windows boot screen does display fwiw.

Read the article

Apache access.log interpretation

- by Pantelis Sopasakis

In the log file of apache (access.log) I find log entries like the following: 10.20.30.40 - - [18/Mar/2011:02:12:44 +0200] "GET /index.php HTTP/1.1" 404 505 "-" "Opera/9.80 (Windows NT 6.1; U; en) Presto/2.7.62 Version/11.01" Whose meaning is clear: The client with IP 10.20.30.40 applied a GET HTTP method on /index.php (that is to say http://mysite.org/index.php) receiving a status code 404 using Opera as client/browser. What I don't understand is entries like the following: 174.34.231.19 - - [18/Mar/2011:02:24:56 +0200] "GET http://www.siasatema.com HTTP/1.1" 200 469 "-" "Python-urllib/2.4" So here what I see is that someone (client with IP 174.34.231.19) accessed http://www.siasatema.com and got a 200 HTTP status code(?). It doesn't make sense to me... the only interpretation I can think of is that my apache server acts like proxy! Here are some other requests that don't have my site as destination... 187.35.50.61 - - [18/Mar/2011:01:28:20 +0200] "POST http://72.26.198.222:80/log/normal/ HTTP/1.0" 404 491 "-" "Octoshape-sua/1010120" 87.117.203.177 - - [18/Mar/2011:01:29:59 +0200] "CONNECT 64.12.244.203:80 HTTP/1.0" 405 556 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:29:59 +0200] "open 64.12.244.203 80" 400 506 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:30:04 +0200] "telnet 64.12.244.203 80" 400 506 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:30:09 +0200] "64.12.244.203 80" 400 301 "-" "-" I believe that all these are related to some kind of attack or abuse of the server. Could someone explain to may what is going on and how to cope with this situation? Update 1: I disabled mod_proxy to make sure that I don't have an open proxy: # a2dismod proxy Where from I got the message: Module proxy already disabled I made sure that there is no file proxy.conf under $APACHE/mods-enabled. Finally, I set on my browser (Mozzila) my IP as a proxy and tried to access http://google.com. I was not redirected to google.com but instead my web page appeared. The same happened with trying to access http://a.b (!). So my server does not really work as a proxy since it does not forward the requests... But I think it would be better if somehow I could configure it to return a status code 403. Here is my apache configuration file: <VirtualHost *:80> ServerName mysite.org ServerAdmin webmaster@localhost DocumentRoot /var/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> Update 2: Using a block, I restrict the use of other methods than GET and POST... <Limit POST PUT CONNECT HEAD OPTIONS DELETE PATCH PROPFIND PROPPATCH MKCOL COPY MOVE LOCK UNLOCK> Order deny,allow Deny from all </Limit> <LimitExcept GET> Order deny,allow Deny from all </LimitExcept> Now methods other that GET are forbidden (403). My only question now is whether there is some trick to boot those how try to use my server as a proxy out...

Read the article

Thoughts on home NAS server

- by user826955

I currently have a NAS with a 2x2TB HDD 1x16GB SSD layout on a mini-itx atom board. The NAS is in a Lian Li PC-Q07 case. On this system I was running freebsd 8 with a gmirror raid 1 setup, which was enough for my needs. So far I was using the NAS for: Fileserver with AFP protocol (only mac clients used) SVN server hosting all my source trees of my projects JIRA (performance was okay-ish) Timemachine backup for the macs The power consumption was about 38W, although I did not put HDDs asleep when unused (I think this is not possible in a raid setup). I liked the NAS because: the performance was good through gigabit LAN (enough for my needs) power consumption was good its a pretty small case and fits in one of my cupboards I disliked the NAS a bit because: it was a bit noisy, the Q07 case vibrated a good amount because of the HDDs. I switched the NAS off every evening I do not have a real backup of the data on the NAS, only the internal raid 1 as safety. I really dont want to loose my source trees under no circumstances, so I would really be sleeping better if I knew I had regular backups somewhere. Recently, the board seemed to have died, I can't boot anymore. Thus, I was thinking about a redesign of my NAS (I still have to find out what parts are broken, I probably need to replace the mainboard and SSD. HDDs seem to be okay). First of all, I was wondering what other users have as backup for their NAS? Are you actually using a second NAS, and regularly copying over the data to have it safe? Or is there any better solution to this? I was thinking about getting a cheap NAS like the synology DS112j with only one disk, and use rsync or something similar to regularly copy data over to the second NAS (wake the second NAS upon start, shut it down after copy). Although this approach seems somewhat weird, It would have the benefit (?) that I could use a single disk instead of raid in the main NAS, and put the disk asleep when idle, and have the NAS running 24/7 with low energy consumption (I found no way to do this with a gmirror setup). Is there any recommended backup solution for a small NAS? Then I was thinking about a different raid setup. Since I have to buy a new mainboard as well as SSD, I might as well switch over to a i3 board with more ram, and also switch to ZFS. I am not familar with ZFS, I've never used it, but I read and hear much about it. Would it be viable to set up a ZFS storage with only 2 disks? Can I easily extend this storage with more disks, once I choose to add some? I could maybe get a new case like the Fractal Design Array R2 which has more 3,5" slots. I could as well get another 2 disks, but I would prefer sticking with the existing 2 for enegery/heat/noise reasons. Should I go for a ZFS storage or stick to my gmirror setup? I would also like to keep freebsd as operating system, and also I dont need any web gui or something (that is, I dont need/want to use FreeNAS or Openfiler etc). Does anyone maybe have a sample setup in use so I can compare energy consumption/noise/software setup? Any guidance towards the NAS of my dreams (silent, low energy, safe w/ backups) much appreciated.

Read the article

Causes of sudden massive filesystem damage? ("root inode is not a directory")

- by poolie

I have a laptop running Maverick (very happily until yesterday), with a Patriot Torx SSD; LUKS encryption of the whole partition; one lvm physical volume on top of that; then home and root in ext4 logical volumes on top of that. When I tried to boot it yesterday, it complained that it couldn't mount the root filesystem. Running fsck, basically every inode seems to be wrong. Both home and root filesystems show similar problems. Checking a backup superblock doesn't help. e2fsck 1.41.12 (17-May-2010) lithe_root was not cleanly unmounted, check forced. Resize inode not valid. Recreate? no Pass 1: Checking inodes, blocks, and sizes Root inode is not a directory. Clear? no Root inode has dtime set (probably due to old mke2fs). Fix? no Inode 2 is in use, but has dtime set. Fix? no Inode 2 has a extra size (4730) which is invalid Fix? no Inode 2 has compression flag set on filesystem without compression support. Clear? no Inode 2 has INDEX_FL flag set but is not a directory. Clear HTree index? no HTREE directory inode 2 has an invalid root node. Clear HTree index? no Inode 2, i_size is 9581392125871137995, should be 0. Fix? no Inode 2, i_blocks is 40456527802719, should be 0. Fix? no Reserved inode 3 (<The ACL index inode>) has invalid mode. Clear? no Inode 3 has compression flag set on filesystem without compression support. Clear? no Inode 3 has INDEX_FL flag set but is not a directory. Clear HTree index? no .... Running strings across the filesystems, I can see there are what look like filenames and user data there. I do have sufficiently good backups (touch wood) that it's not worth grovelling around to pull back individual files, though I might save an image of the unencrypted disk before I rebuild, just in case. smartctl doesn't show any errors, neither does the kernel log. Running a write-mode badblocks across the swap lv doesn't find problems either. So the disk may be failing, but not in an obvious way. At this point I'm basically, as they say, fscked? Back to reinstalling, perhaps running badblocks over the disk, then restoring from backup? There doesn't even seem to be enough data to file a meaningful bug... I don't recall that this machine crashed last time I used it. At this point I suspect a bug or memory corruption caused it to write garbage across the disks when it was last running, or some kind of subtle failure mode for the SSD. What do you think would have caused this? Is there anything else you'd try?

Read the article

Forwarding rsyslog to syslog-ng, with FQDN and facility separation

- by Joshua Miller

I'm attempting to configure my rsyslog clients to forward messages to my syslog-ng log repository systems. Forwarding messages works "out of the box", but my clients are logging short names, not FQDNs. As a result the messages on the syslog repo use short names as well, which is a problem because one can't determine which system the message originated from easily. My clients get their names through DHCP / DNS. I've tried a number of solutions trying to get this working, but without success. I'm using rsyslog 4.6.2 and syslog-ng 3.2.5. I've tried setting $PreserveFQDN on as the first directive in /etc/rsyslog.conf (and restarting rsyslog of course). It seems to have no effect. hostname --fqdn on the client returns the proper FQDN, so the problem isn't whether the system can actually figure out its own FQDN. $LocalHostName <fqdn> looked promising, but this directive isn't available in my version of rsyslog (Available since 4.7.4+, 5.7.3+, 6.1.3+). Upgrading isn't an option at the moment. Configuring the syslog-ng server to populate names based on reverse lookups via DNS isn't an option. There are complexities with reverse DNS and the public cloud. Specifying for the forwarder to use a custom template seems like a viable option at first glance. I can specify the following, which causes local logging to begin using the FQDN on the syslog-ng repo. $template MyTemplate, "%timestamp% <FQDN> %syslogtag%%msg%" $ActionForwardDefaultTemplate MyTemplate However, when I put this in place syslog-ng seems to be unable to categorize messages by facility or priority. Messages come in as FQDN, but everything is put in to user.log. When I don't use the custom template, messages are properly categorized under facility and priority, but with the short name. So, in summary, if I manually trick rsyslog into including the FQDN, priority and facility becomes lost details to syslog-ng. How can I get rsyslog to do FQDN logging which works properly going to a syslog-ng repository? rsyslog client config: $ModLoad imuxsock.so # provides support for local system logging (e.g. via logger command) $ModLoad imklog.so # provides kernel logging support (previously done by rklogd) $ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat *.info;mail.none;authpriv.none;cron.none /var/log/messages authpriv.* /var/log/secure mail.* -/var/log/maillog cron.* /var/log/cron *.emerg * uucp,news.crit /var/log/spooler local7.* /var/log/boot.log $WorkDirectory /var/spool/rsyslog # where to place spool files $ActionQueueFileName fwdRule1 # unique name prefix for spool files $ActionQueueMaxDiskSpace 1g # 1gb space limit (use as much as possible) $ActionQueueSaveOnShutdown on # save messages to disk on shutdown $ActionQueueType LinkedList # run asynchronously $ActionResumeRetryCount -1 # infinite retries if host is down *.* @syslog-ng1.example.com *.* @syslog-ng2.example.com syslog-ng configuration (abridged for brevity): options { flush_lines (0); time_reopen (10); log_fifo_size (1000); long_hostnames (off); use_dns (no); use_fqdn (yes); create_dirs (no); keep_hostname (yes); }; source src { unix-stream("/dev/log"); internal(); udp(ip(0.0.0.0) port(514)); }; destination per_host_destination { file( "/var/log/syslog-ng/devices/$HOST/$FACILITY.log" owner("root") group("root") perm(0644) dir_owner(root) dir_group(root) dir_perm(0775) create_dirs(yes)); }; log { source(src); destination(per_facility_destination); };

Read the article

Supermicro IPMI on MBD-X8DAH+-F-O motherboard. Keyboard and mouse do not work after booting Windows Server 2008 R2

- by LDelgado

Hell Everyone, I built a server with the mentioned motherboard. I installed Windows Server 2008 R2 Enterprise on this server. IPMI is integrated on the motherboard with its own dedicated NIC. I've got that NIC configured with its own IP address. I can remote into it using IPMI, and I can remotely control the server settings before booting the OS ( BIOS, RAID configuration, etc). When the OS boots, I lose the mouse and keyboard. I cannot use the keyboard or mouse when installing the OS either. So the Keyboard and Mouse only work when no OS is loaded. Once the OS loads I lose it - that is my problem. I've been doing some research and trying a few things, but I have not been successful in fixing this issue. I may be wrong, but based on the things I've found online, it seems that the problem could be caused by the way the OS handles USB. The server is headless. There is no keyboard, mouse, or monitor plugged into it. When I boot up the OS and remote into it, I cannot see a mouse or keyboard listed in the Device Manager. Based on what I've read, it seems that the OS should detect a mouse and a keyboard when connecting remotely via IPMI. The following are the solutions I've tried. Nothing has worked so far: I've updated the firmware of the IPMI component to the latest firmware - 1.33. I made sure that the mouse mode was set to Absolute (Windows OS). I've loaded the factory defaults several times. I've enabled Port64h/60h Emulation under the USB settings in the BIOS. I've disabled USB legacy support in the BIOS. I made sure the firewall wasn't blocking IPMI (disabled the firewall). And that's about it. I've found threads in some forums from people having the same issue as me, but they were not running the same OS. They were either running Linux or FreeBSD. Most of them fixed their problem by selecting the right mouse mode (Linux in their case). There was one other that solved the problem by disabling USB Mass Storage mode. He stated "When I set it to disable USB Mass Storage when no image is loaded, the ukbd came alive, and I'm typing this on the IPMI Console. " source: http://freebsd.1045724.n5.nabble.com/IPMI-Console-No-luck-once-OS-is-booted-td3967868.html I suspect the solution described in the previous paragraph is somehow related to my problem. I've found several threads on the internet with issues describing the same problem, but none of them were with Windows Server 2008 R2. Again, I may be wrong, but it seems like that could be the issue. I just don't know how I go about applying a solution in Windows Server 2008 R2. In any case, I could use your expertise. Maybe I am missing something, or maybe I'm on the right track. Your help is much appreciated. Thank you in advance,

Read the article

Windows 7 inbuilt and 3rd party (de)fragmentation related queries

- by Karan

I have a pretty good idea of how files end up getting fragmented. That said, I just copied ~3,200 files of varying sizes (from a few KB to ~20GB) from an external USB HDD to an internal, freshly formatted (under Windows 7 x64), NTFS, 2TB, 5400RPM, WD, SATA, non-system (i.e. secondary) drive, filling it up 57%. Since it should have been very much possible for each file to have been stored in one contiguous block, I expected the drive to be fragmented not more than 1-2% at most after this rather lengthy exercise (unfortunately this older machine doesn't support USB 3.0). Windows 7's inbuilt defrag utility told me after a quick analysis that the drive was fragmented only 1% or so, which dovetailed neatly with my expectations. However, just out of curiosity I downloaded and ran the latest portable x64 version of Piriform's Defraggler, and was shocked to see the drive being reported as being ~85% fragmented! The portable version of Auslogics Disk Defrag also agreed with Defraggler, and both clearly expected to grind away for ~10 hours to completely defragment the drive. 1) How in blazes could the inbuilt and 3rd party defrag utils disagree so badly? I mean, 10-20% variance is probably understandable, but 1% and 85% are miles apart! This Engineering Windows 7 blog post states: In Windows XP, any file that is split into more than one piece is considered fragmented. Not so in Windows Vista if the fragments are large enough – the defragmentation algorithm was changed (from Windows XP) to ignore pieces of a file that are larger than 64MB. As a result, defrag in XP and defrag in Vista will report different amounts of fragmentation on a volume. ... [Please read the entire post so the quote is not taken out of context.] Could it simply be that the 3rd party defrag utils ignore this post-XP change and continue to use analysis algos similar to those XP used? 2) Assuming that the 3rd party utils aren't lying about the real extent of fragmentation (which Windows is downplaying post-XP), how could the files have even got fragmented so badly given they were just copied over afresh to an empty drive? 3) If vastly differing analysis algos explain the yawning gap, which do I believe? I'm no defrag fanatic for sure, but 85% is enough to make me seriously consider spending 10 hours defragging this drive. On the other hand, 1% reported by Windows' own defragger clearly implies that there is no cause for concern and defragging would actually have negative consequences (as per the post). Is Windows' assumption valid and should I just let it be, or will there be any noticeable performance gains after running one of the 3rd party utils for 10 hours straight? 4) I see that out of the box Windows 7 defrag is scheduled to run weekly. Does anyone know whether it defrags every single time, or only if its analysis reveals a fragmentation percentage over a set threshold? If the latter, what is this threshold and can it be changed, maybe via a Registry edit? Thanks for reading through (my first query on this wonderful site!) and for any helpful replies. Also, if you're answering question #3, please keep in mind that any speed increases post defragging with 3rd party utils vis-à-vis Windows' inbuilt program should not include pre-Vista (preferably pre-Win7) examples. Further, examples of programs that made your system boot faster won't help in this case, since this is a non-system drive (although one that'll still be used daily).

Read the article

Setup access to SAS RAID drives with NTFS partitions on CentOS Machine

- by Quanano

We have a Dell Poweredge 2900 system with Adaptec 39320A SCSI CONTROLLER CARD and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on the other raid array with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log

Read the article

Wi-Fi Stick with ZD1211 chip refuses to work on Ubuntu >8.10. No clue.

- by Benjamin Maus

I have a machine running Ubuntu 9.10 (Karmic *x86_64*). Everything is running smooth so far, except for the Wi-Fi USB Stick. The same device worked perfectly in 8.10. The wireless device is a GW-US54GXS using the Zydas Zd1211 chipset. Dmesg output after plugging in: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' [ 196.304209] zd1211rw 2-1:1.0: phy0 [ 196.304227] usbcore: registered new interface driver zd1211rw [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Syslog output: Nov 5 11:20:24 somesystem kernel: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' Nov 5 11:20:24 kierkegaard NetworkManager: <info> Found radio killswitch rfkill0 (at /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/ieee80211/phy0/rfkill0) (driver <unknown>) Nov 5 11:20:24 somesystem kernel: [ 196.304209] zd1211rw 2-1:1.0: phy0 Nov 5 11:20:24 somesystem kernel: [ 196.304227] usbcore: registered new interface driver zd1211rw Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): new 802.11 WiFi device (driver: 'zd1211rw') Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/2 Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): now managed Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): device state change: 1 -> 2 (reason 2) Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): bringing up device. Nov 5 11:20:24 somesystem kernel: [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:24 somesystem kernel: [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 Nov 5 11:20:24 somesystem kernel: [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- Nov 5 11:20:24 somesystem NetworkManager: <WARN> nm_device_hw_bring_up(): (wlan0): device not up after timeout! Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): deactivating device (reason: 2). Nov 5 11:20:24 somesystem kernel: [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:29 somesystem wpa_supplicant[978]: Could not set interface 'wlan0' UP Nov 5 11:20:29 somesystem wpa_supplicant[978]: Failed to initialize driver interface Nov 5 11:20:29 somesystem NetworkManager: <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. Gnome tells me in the network menu that the device was "not ready". It appears in iwconfig but not in ifconfig. The same symptoms appear when I boot from the live CD. How can I solve this dilemma?

Read the article

Why are USB 2.0 devices crashing my system?

- by BenAlabaster

Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic baby-ATX motherboard with no identifying markings. CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. There's one stamp on the motherboard that says "Rev.B". On board it has 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. It has an 80Gb Western Digital hard drive freshly formatted and built with Windows XP Professional with Service Pack 3 and all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 crashes the machine as soon as it starts up). It's got a Daytek MV150 15" touch screen running through the VGA and COM1 with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem If I hook any USB 2.0 devices to this machine, it hangs the whole machine and I have to hard boot it to get it back up. Workarounds found I can plug the same devices into the on board USB 1.0 connectors and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions I've tried disabling all the on board devices that I'm not using - such as the on board LAN, the second COM port, the AGP connector etc. through the BIOS in an (perhaps misguided or futile) attempt to reduce the power consumption... I don't think it had any effect but it didn't do any harm. I was wondering if the PSU wattage just isn't enough to drive the USB 2.0 devices; I've seen this suggested but haven't found any confirmation that this could really be an issue - nor have I found a way to work around this issue - if indeed it is one. Any ideas? The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference. I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself. Other thoughts Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

Read the article

ovs-vsctl: "eth0" is not a valid UUID

- by Przemek Lach

I'm trying to setup an open v-switch inside my Ubuntu 12.04 Server VM. I have created three interfaces for this VM and I want to create a port mirror inside of the VM using these there interfaces and open v-switch. There are three Host-Only Adapters: eth0, eth1, eth2. The idea is that three other VM's will be connected to these adapters. One of these VM's will stream UDP video to eth0 and I want the vswitch'd VM to mirror those packets from eth0 onto eth1 and eth2. Each of the VM's connected to eth1 and eth2 will get the same video stream. I performed the following steps to install open v-switch: $ apt-get install python-simplejson python-qt4 python-twisted-conch automake autoconf gcc uml-utilities libtool build-essential $ apt-get install build-essential autoconf automake pkg-config $ wget http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ tar xf http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ cd http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ apt-get install libssl-dev iproute tcpdump linux-headers-`uname -r` $ ./boot.sh $ ./configure - -with-linux=/lib/modules/`uname -r`/build $ make $ sudo make install After installation I configured as follows: $ insmod datapath/linux/openvswitch.ko $ sudo touch /usr/local/etc/ovs-vswitchd.conf $ mkdir -p /usr/local/etc/openvswitch $ ovsdb-tool create /usr/local/etc/openvswitch/conf.db Then I started the server: $ ovsdb-server /usr/local/etc/openvswitch/conf.db \ --remote=punix:/usr/local/var/run/openvswitch/db.sock \ --remote=db:Open_vSwitch,manager_options \ --private-key=db:SSL,private_key \ --certificate=db:SSL,certificate \ --bootstrap-ca-cert=db:SSL,ca_cert --pidfile --detach --log-file $ ovs-vsctl –no-wait init (run only once) $ ovs-vswitchd --pidfile --detach The above steps I got from this tutorial and it all worked fine. I then proceeded to add a port mirror based on the open v-switch documentation under Port Mirroring. I successfully completed the following commands: $ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 eth1 $ ovs-vsctl add-port br0 eth2 $ ifconfig eth0 promisc up $ ifconfig eth1 promisc up $ ifconfig eth2 promisc up At this point when I run ovs-vsctl show I get the following: 75bda8c2-b870-438b-9115-e36288ea1cd8 Bridge "br0" Port "br0" Interface "br0" type: internal Port "eth0" Interface "eth0" Port "eth2" Interface "eth2" Port "eth1" Interface "eth1" And when I run ifconfig I get the following: eth0 Link encap:Ethernet HWaddr 08:00:27:9f:51:ca inet6 addr: fe80::a00:27ff:fe9f:51ca/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth1 Link encap:Ethernet HWaddr 08:00:27:53:02:d4 inet6 addr: fe80::a00:27ff:fe53:2d4/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth2 Link encap:Ethernet HWaddr 08:00:27:cb:a5:93 inet6 addr: fe80::a00:27ff:fecb:a593/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth3 Link encap:Ethernet HWaddr 08:00:27:df:bb:d8 inet addr:192.168.1.139 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fedf:bbd8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2211 errors:0 dropped:0 overruns:0 frame:0 TX packets:1196 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:182987 (182.9 KB) TX bytes:125441 (125.4 KB) NOTE: I use eth3 as a bridge adapter for SSH'ing into the VM. So now, I think I've done everything correctly but when I try to create the bridge using the following command: $ ovs-vsctl -- set Bridge br0 mirrors=@m -- --id=@eth0 get Port eth0 -- --id=@eth1 get Port eth1 -- --id=@m create Mirror name=app1Mirror select-dst-port=eth0 select-src-port=@eth0 output-port=@eth1,eth2 I get the following error: ovs-vsctl: "eth0" is not a valid UUID I don't understand why it's not able to find the interfaces?

Read the article

What seems to be plaguing my hard drives?

- by Craig

In a little bit of a tech nightmare here. I know oodles about software, not so much more than the above average user about hardware. I recently had to toss an old desktop of mine. It was gradually getting slower and slower, and after shutting the desktop down for long periods of time, it would choke up upon startup. Sometimes it'd give a disk read error, sometimes say no OS was found, etc. Restarting it about 5-15 times would eventually boot properly. Weird. I also noticed that startup programs were going missing, Dropbox was reindexing my entire folder, and Backblaze was backing up less than the number of files that it should. This lead me to believe it was probably a hard drive issue. I began to wonder why I'd have hard drive issues, and came to closure when I assumed it was because of recent power surges and outages. I'm sure that does a number on the drive. I bought a new desktop recently. It's not a beast or anything, but it's enough for what I do. It's an eMachines (I know, I know) Ultra-Slim (http://www.amazon.com/eMachines-Ultra-Slim-ER1401-57-Desktop-PC/dp/B00475OG9U). This is ideal for me because it's small and portable. It comes with an AC adapter and battery, like a laptop. Just to be safe, I bought an uninterruptable power supply on top of that. It's basically protected completely from any outages that might scramble the drive. I set this up a few days ago and for the past few days I've been perfecting settings, downloading the usual applications, etc. Two days ago, I noticed Dropbox was reindexing my entire Dropbox folder. I installed both Dropbox and Backblaze on this system, but it is very much more lightweight than the other. Only about 15 third-party applications installed. I thought that maybe Dropbox and Backblaze were stressing my system, so I turned off Backblaze. Still, Dropbox runs and comes across this infinite reindex issue. I noticed that upon a reboot recently, two applications did not start on startup either. Also, much like my old desktop, every 3rd or 4th reboot, I'll be forced into a chkdsk. This makes me incredibly nervous. What could possibly be going wrong with my old, years-old desktop that is immediately causing the same issues to my new one? I've considered all of the basics. I'm in a very air conditioned room. I take run routine virus scans. I'd like to think I take care of my systems very well. What is this issue that is haunting me? There's always the possibility that this new desktop has a junk hard drive, but it just seems way too coincidental.

Read the article

Computer not POSTing "randomly"?

- by smoth190

I have a custom built PC that is exhibiting some...odd... behavior, something I've never seen before. It was working fine one day, and the next day, it wouldn't start. Seeing as I wanted an upgrade anyway, I purchased a new motherboard that was compatible with all my parts. While replacing the motherboard, I accidentally damaged the CPU. Well, I wanted a new one anyway... so I got a new one. Seeing as I was replacing a ton of parts already, I bought a new PSU because the old one was super loud. When I slapped it all together, it starts up, lights, fans, drives, they all start. But I get no display from the monitor. No beeps, which I believe means it doesn't POST. I figured it was the RAM, because after removing the sound card and graphics card, there was nothing else that I hadn't replaced. When I remove both sticks of RAM, I get a continuous beeping, and according to the mobo handbook, means no RAM. So I think the mobo is functional, or atleast partly. I bought new RAM, but it still didn't work. I tried 3 monitors, with both VGA and DIV. So it's probably not the monitor, either. Now, let me get to the random part. Every 20 or so boots (I should also mention, for about 3 out of 5 boots I have to unplug the PC because it won't powerdown via the button), it will POST and I'll get display. Then, after about 2 or 3 resets, it won't work again. This confuses me so much, because even when I change nothing, it will/will not work. My thought is that maybe it has something to do with the RAM not clearing or something. I also reset the CMOS battery, incase that had anything to do with it, but no eval. I found some weird suggestion online about holding the power button for 30 seconds while it was unplugged. That did nothing, but I didn't expect it would... I've replaced just about the entire computer, and all the parts are compatible. Done about everything I can think of, but nothing has worked. Hopefully someone can help me here. And as I side note: When I do get my computer to boot, it says my hardware has changed and I have to re-activate windows. But it says I have to call Microsoft to do it. So I get this fancy automated voice that asks me to enter in a code into windows, then it asks me "How many computers have you activated with this copy of Windows?". Well, I had it on my computer before I replaced everything, so I said 1. Then he yelled at me for violating my 1-use license. I dunno what's going on there, do I have to re-purchase Windows 7? And they wonder why people pirate software... That's just a bonus question, though. Specs: 8GB of DDR2 RAM (Corsair) AMD CPU (I don't know what GHz or model because I can't find the box... (I think its 4 cores of 2.8Ghz) ASRock A785GM-LE Motherboard

Read the article

how to adjust the size of the root partition on live arch linux system (/dev/mapper/arch_root-image)

- by leon

Summary: I created a bootable usb drive with a live Bridge linux (ARCH based) on it. Everything works fine. The live system mounts a device called /dev/mapper/arch_root-image as its ext4 root partition (/ mount point). The problem is that I dont know how to control the size of this partition. This is not a Bridge specific issue (also happens with Archbang) Detail: My usb drive has a dos partition table with 2 ext2 partitions $ fdisk -l /dev/sdb Disk /dev/sdb: 29,8 GiB, 32006733824 bytes, 62513152 sectors Unités : secteur de 1 × 512 = 512 octets Taille de secteur (logique / physique) : 512 octets / 512 octets taille d'E/S (minimale / optimale) : 512 octets / 512 octets Type d'étiquette de disque : dos Identifiant de disque : 0x0007b7e2 Périphérique Amorçage Début Fin Blocs Id Système /dev/sdb1 * 2048 2002943 1000448 83 Linux /dev/sdb2 2002944 32258047 15127552 83 Linux sdb1 is approx 1GB and sdb2 is 14GB. The live system is on sdb1. sdb2 is empty. Now when I boot the live system, its filesystem looks like this: $ mount proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) sys on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) dev on /dev type devtmpfs (rw,nosuid,relatime,size=505272k,nr_inodes=126318,mode=755) run on /run type tmpfs (rw,nosuid,nodev,relatime,mode=755) /dev/sda1 on /run/archiso/bootmnt type ext2 (ro,relatime) cowspace on /run/archiso/cowspace type tmpfs (rw,relatime,size=772468k,mode=755) /dev/loop0 on /run/archiso/sfs/root-image type squashfs (ro,relatime) /dev/mapper/arch_root-image on / type ext4 (rw,relatime) securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /sys/fs/cgroup type tmpfs (rw,nosuid,nodev,noexec,mode=755) cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,release_agent=/usr/lib/systemd/systemd-cgroups-agent,name=systemd) pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime) cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset) cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpuacct,cpu) cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory) cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices) cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer) cgroup on /sys/fs/cgroup/net_cls type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls) cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio) mqueue on /dev/mqueue type mqueue (rw,relatime) debugfs on /sys/kernel/debug type debugfs (rw,relatime) hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime) configfs on /sys/kernel/config type configfs (rw,relatime) systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=36,pgrp=1,timeout=300,minproto=5,maxproto=5,direct) tmpfs on /tmp type tmpfs (rw) tmpfs on /etc/pacman.d/gnupg type tmpfs (rw,relatime,mode=755) As we can see, the root partition is from the device /dev/mapper/arch_root-image and my problem is that the live system recognizes it as a 3.9GB drive $ df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/arch_root-image 3.9G 1.9G 2.1G 48% / dev 494M 0 494M 0% /dev run 503M 23M 481M 5% /run /dev/sda1 962M 590M 324M 65% /run/archiso/bootmnt cowspace 755M 32M 723M 5% /run/archiso/cowspace /dev/loop0 520M 520M 0 100% /run/archiso/sfs/root-image tmpfs 503M 132K 503M 1% /dev/shm tmpfs 503M 0 503M 0% /sys/fs/cgroup tmpfs 503M 360K 503M 1% /tmp tmpfs 503M 896K 503M 1% /etc/pacman.d/gnupg My question is how is this size controled? I suspect this is related to the content of the aitab file which is part of the Bridge iso image: $ cat aitab # <img> <mnt> <arch> <sfs_comp> <fs_type> <fs_size> root-image / i686 xz ext4 50% I have read https://wiki.archlinux.org/index.php/archiso#aitab but found no clue

Read the article

Windows 7 disk errors after a few hours of runtime

- by GFK

I'm having trouble understanding what is going on with my work PC. Whenever I boot it, it runs fine for a while, then starts to randomly show disk errors. The displayed error often contains the message "not enough storage is available to process this command", although depending on the application that fails it can be different. This has happened for weeks now and is getting worse. This is what troubles me: It never seems to impact critical parts of the system (no BSOD, no freeze). Only some applications seem impacted, refusing to function correctly after a while: Outlook 2010 cannot download RSS feeds anymore, Firefox 6 or IE9 cannot download anything bigger than 3MB without failing, Windows Update fails, all msi installers fail, Visual Studio 2010 starts failing in weird manners... It only happens after a while using it (typically 3 hours, but it seems that installing a program or compiling several times makes it shorter) Rebooting solves it (temporarily). The system: The OS is Windows 7 Pro Spanish SP1, 32 bits The system is an HP Compaq 6000 Pro with 4 GB memory (only 3.4GB usable since the system is 32bit), one 500GB hard drive. Installed applications include: Visual Studio 2010, SQL Server 2008 R2, VMWare Workstation 7, Microsoft Security Essentials, Office 2010. Shutting down all related services and processes doesn't seem to change anything. The diagnostics I've run so far: Hard drive : 465GB, 165GB free Process Explorer : physical and virtual memory seem ok (pagefile is 5.3GB, physical memory usage 70%, system commit 39%) Windows Memory diagnostic tool: OK CHKDSK returned: 488282111 KB total disk space. 281668248 KB in 265779 files. 150188 KB in 62949 indexes. 0 KB in bad sectors. 571755 KB in use by the system. The log file has occupied 65536 kilobytes. 205891920 KB available on disk. For non-spanish speakers, that means all ok. SMART diagnostic tools (DiskCheckup) report all values normal. temperatures are in the normal range (HWinfo). The event viewer doesn't seem to contain any significant message. ran CCleaner 3, without any noticeable effect. I was thinking about some file number limit (between Visual Studio projects and other applications, there are around 300.000 files on the hard drive), but I couldn't find any. It's possible there is something related with the use of the temporary folders (it's the only explanation I have for why applications fail but Windows doesn't), but I cannot confirm that. Only thing I cannot find out is if chkdsk reporting 65MB for the log is normal. It seems since Vista it always reports this. Any other cleaning/diagnostic tool you might know of? Edit: I ran several other tools since I first published the question: Seagate SeaTools (the HD manufacturer's analysis tool): complete test run OK. Intel Rapid 10.1 (the HD controller manufacturer's troubleshooting tool): the HD's ok. Microsoft Desktop Heap Monitor: Desktop Heap Information Monitor Tool (Version 8.1.2925.0) Copyright (c) Microsoft Corporation. All rights reserved. Session ID: 1 Total Desktop: ( 46464 KB - 11 desktops) WinStation\Desktop Heap Size(KB) Used Rate(%) WinSta0\Winlogon (s1) 128 3.6 WinSta0\Disconnect (s1) 64 3.8 WinSta0\Default (s1) 20480 3.0 msswindowstation\mssrestricteddesk (s0) 1024 0.2 __X78B95_89_IW__A8D9S1_42_ID (s0) 1024 0.2 Service-0x0-3e5$\Default (s0) 1024 0.6 Service-0x0-3e4$\Default (s0) 1024 0.3 Service-0x0-3e7$\Default (s0) 1024 2.1 WinSta0\Winlogon (s0) 128 1.9 WinSta0\Disconnect (s0) 64 3.8 WinSta0\Default (s0) 20480 0.0 All ok, desktop heap usage < 5% Edit 2: I tried totally resetting my account by creating a new one, logging under this new one and delete the first one (local rights and files), then logging back with this deleted account (it is a domain account). No luck. Also, I found out often the error is "not enough storage is available to process this command". Searching on the internet, I found an old troubleshooting tip (setting a registry key to raise the IRP stack limit, whatever it is) which did not change anything.

Read the article

"ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver" wheel-click is wrong

- by sputnick

I use this mouse under archlinux x86_64 with 3.2.8-1-ARCH kernel. I have some problems to select and then paste with the wheel-click in some applications like konversation, not in a terminal nor an editor. I don't know if it's a hardware problem or a software one. $ lsusb -v Bus 002 Device 110: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x046d Logitech, Inc. idProduct 0xc50e Cordless Mouse Receiver bcdDevice 25.10 iManufacturer 1 Logitech iProduct 2 USB RECEIVER iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 34 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 70mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.11 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 95 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) When I see what's happens in xev, the output is different compared to another mouse My buggy Logitech mouse : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350700, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350700, (48,52), root:(1491,75), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 16 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350988, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350988, (48,52), root:(1491,75), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 a working mouse (dell) : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245131, (46,32), root:(1489,55), state 0x10, button 2, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245131, (46,32), root:(1489,55), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 528 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245411, (46,32), root:(1489,55), state 0x210, button 2, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245411, (46,32), root:(1489,55), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 A demo of the problem when I use konversation (IRC) : http://www.youtube.com/watch?v=lhmr92M7NCc I tried to modify the button map with xmodmap like this with no success (one at a time) : xmodmap -e "pointer = 1 0 3" xmodmap -e "pointer = 1 1 3" xmodmap -e "pointer = 1 2 3" xmodmap -e "pointer = 1 3 3" xmodmap -e "pointer = 1 4 3" xmodmap -e "pointer = 1 5 3" xmodmap -e "pointer = 1 6 3" xmodmap -e "pointer = 1 7 3" xmodmap -e "pointer = 1 8 3" xmodmap -e "pointer = 1 9 3" xmodmap -e "pointer = 1 10 3" xmodmap -e "pointer = 1 11 3" xmodmap -e "pointer = 1 12 3" xmodmap -e "pointer = 1 13 3" xmodmap -e "pointer = 1 14 3" xmodmap -e "pointer = 1 15 3" xmodmap -e "pointer = 1 16 3" xmodmap -e "pointer = 1 17 3" xmodmap -e "pointer = 1 18 3" xmodmap -e "pointer = 1 19 3" xmodmap -e "pointer = 1 20 3" xmodmap -e "pointer = 1 21 3" xmodmap -e "pointer = 1 22 3" xmodmap -e "pointer = 1 23 3" xmodmap -e "pointer = 1 24 3" xmodmap -e "pointer = 1 25 3" Any clue ? I would like to avoid buying a new mouse just for a paste problem.

Search Results

Search found 9273 results on 371 pages for 'boot repair'.

Page 364/371 | < Previous Page | 360 361 362 363 364 365 366 367 368 369 370 371 | Next Page >

- by bart613

- by Iain Elder

- by mejpark

- by András Szepesházi

- by Fabio

- by joelmaranhao

- by senorsmile

- by buecking

- by Jim Fell

- by Matt

- by Pantelis Sopasakis

- by user826955

- by poolie

- by Joshua Miller

- by LDelgado

- by Karan

- by Quanano

- by Benjamin Maus

- by BenAlabaster

- by Przemek Lach

- by Craig

- by smoth190

- by leon

- by GFK

- by sputnick

< Previous Page | 360 361 362 363 364 365 366 367 368 369 370 371 | Next Page >