Search Results

Search found 23897 results on 956 pages for 'installation configuration'.

Page 365/956 | < Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >

• WNDR3700 Router + Cisco SG200-08 + LACP + Dual Uplink

  - by kobaltz

  Background I have a storage server that has several virtual machine images stored on them. I would store them locally, but I have limited space on my desktop (using SSD storage). I would like to increase the bandwidth between the desktop and the storage server by using two NICs on each computer. My original configuration allowed about 55MBps between the desktop and storage server. This storage server also has several TBs of documents, pictures, movies, vms, and ISO/programs. The storage server has 8 1.5TB hard drives in a RAID 10 configuration with a hardware RAID controller. The benchmarks on the RAID 10 are about 300MBps. Configuration In short, I am trying to bridge my switch and router. The switch is a small 8 port Cisco smart switch that supports 802.3ad LACP. I have two computers plugged into the switch, each with 2 Intel Gigabit NICs. The first computer is a Windows 7 machine that has the Intel ANS software installed. I have LACP configured with the computer and now show 3 NICs (2 Physical + 1 TEAM Virtual @ 2Gbps). It looks like this computer is configured correctly. I trunked the two ports that this computer is plugged into with the switch's web interface. The second computer is a homebrew storage box running debian. I also have the bonding enabled on this machine and the switch configured with LACP. Without having the WNDR3700 router in the picture yet, I am able to communicate between the Windows 7 machine and the debian box since they both have static IP addresses. With LACP enabled on both machines I am getting about 106-108MBps speeds. Issue I plug in a network cable from the switch into the router and enable DHCP on the desktop. I saw no need to have a static address on the desktop. My transfer rates are still from 106MBps-108MBps. While this is still a boost, I am trying to figure out how to get about 140-180MBps. I am thinking that I need to increase the bandwidth from the router to the switch. My switch allows 4 groups for port trunking. I plugged in a second network cable from the router to the switch. My question is, what is the proper way to fix this issue. Should I port trunk the two ports that are going from the switch to the router? Keep in mind that the router is a WNDR3700 and is unsure whether or not it supports LACP. I do have OpenWRT installed on the router, but it still wasn't clear in any documentation that I found if it supported 802.3ad LACP standards. I am also wondering if there needs to be anything changed within the Cisco settings. [Edit] - Corrected some numbers, wasn't really paying attention. It looks like the speeds though at least two NICs are bonded with LACP is still reaching the max bandwidth of one port. Is there a way to configure the switch so that I can increase this bandwidth? Also, on the storage server, I had a couple of extra NICs laying around and threw them on there as well. Another EDIT and More Findings I happened to look at the traffic of each individual NIC and think that I see the problem. I tested with a simple transfer for a 4GB file. I noticed that only one of the NICs was taking the load of the traffic. I then copied the file back to the Storage Server and noticed that the other NIC was sending out the traffic. I have 802.3ad LACP enabled on the two NICs and I see that it gets enabled dynamically on the switch's interface. Should I be using Static Link Aggregation?

  Read the article

• Print directly to CUPS server from non-local clients (Ubuntu 14.04)

  - by OEP

  I set up a CUPS server with a few queues and printing from local clients (the CUPS test page and Samba) seems to work just fine. It seems like the CUPS server is denying non-local clients though: 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 390 Validate-Job successful-ok 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 339 Create-Job client-error-not-authorized localhost - - [03/Jun/2014:14:40:50 -0400] "POST /printers/m137 HTTP/1.1" 200 410869 Print-Job successful-ok This makes me think I have some sort of host-based restriction in my configuration file, but I can't find it. I've even set my default policy to Allow all only to get the same log message. I'm working from a configuration file which had previously worked on an older version of CUPS, which looks quite similar to the example cupsd.conf. I could be wrong but it looks like that final <Limit All> block ought to allow the actions the logs complain about. MaxLogSize 2000000000 # Log general information in error_log - change "info" to "debug" for # troubleshooting... LogLevel info #AccessLog syslog #ErrorLog syslog #PageLog syslog # Administrator user group... SystemGroup sys root lp # Only listen for connections from the local machine. Listen 0.0.0.0:631 Listen :::631 Listen /var/run/cups/cups.sock ServerName <snipped> # Show shared printers on the local network. Browsing Off BrowseOrder allow,deny # (Change '@LOCAL' to 'ALL' if using directed broadcasts from another subnet.) BrowseAllow @LOCAL # Default authentication type, when authentication is required... DefaultAuthType Basic # Restrict access to the server... <Location /> Order allow,deny Allow all </Location> # Restrict access to the admin pages... <Location /admin> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Restrict access to configuration files... <Location /admin/conf> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Set the default printer/job policies... <Policy default> # Job-related operations must be done by the owner or an administrator... <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order allow,deny </Limit> </Policy>

  Read the article

• KVM with one host IP and a different subnet for machines

  - by Jguy

  I've already setup a KVM host with proper IP configurations, but my host had me create DHCP and use that to assign the IP's to the machines. I want to see if there's an easier way to do it (or better). Upon my first setting out on this, I didn't find anything that pointed me in the right direction. I'm coming off a fresh install of Debian 6.0 x64, so I have nothing installed. I've logged in, queried for the below information and changed the password from my host set one. I have a Debian 6.0 x64 system with the following initial network configuration (substituted 255 in place of my real first octave): # tail /etc/network/interfaces auto eth0 iface eth0 inet static address 255.9.24.80 broadcast 255.9.24.95 netmask 255.255.255.224 gateway 255.9.24.65 # default route to access subnet up route add -net 255.9.24.64 netmask 255.255.255.224 gw 255.9.24.65 eth0 I have a /29 subnet that I want the virtual machines to use from my host: IP: 255.46.187.152 /29 Mask: 255.255.255.248 Broadcast: 255.46.187.159 Usable IP addresses: 255.46.187.153 to 255.46.187.158 I like the interface of Cloudmin, so I want to try and use that if I can to administrate my guests. So, my questions: How do I set this up on the host system the best so that I can use the additional Subnet IP's on the guests and have them accessible from the internet? I also need to host a DNS server, which means one of these VM's has to have two IP's assigned to it and accessable from the outside world. How can I do that using Cloudmin? I had a question about this here: Multiple IP addresses assigned to one KVM VM But I just reformatted the entire server and am trying to figure out a better way of doing this. Machine information: # ip route show 255.9.24.64/27 via 255.9.24.65 dev eth0 255.9.24.64/27 dev eth0 proto kernel scope link src 255.9.24.80 default via 255.9.24.65 dev eth0 brctl is empty # ip addr list 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether c8:60:00:54:b5:d8 brd ff:ff:ff:ff:ff:ff inet 255.9.24.80/27 brd 255.9.24.95 scope global eth0 inet6 fe80::ca60:ff:fe54:b5d8/64 scope link valid_lft forever preferred_lft forever Thank you for any help you can provide me. EDIT: I've installed kvm and cloudmin: aptitude install qemu-kvm libvirt-bin wget http://cloudmin.virtualmin.com/gpl/scripts/cloudmin-kvm-debian-install.sh ./cloudmin-kvm-debian-install.sh Rebooted and now my network configuration looks like this: # device: eth0 iface eth0 inet manual # default route to access subnet iface br0 inet static address 255.9.24.80 netmask 255.255.255.224 broadcast 255.9.24.95 network 255.9.24.64 bridge_ports eth0 gateway 255.9.24.65 I setup in Cloudmin the Start IP as 255.46.187.153 and End IP as 255.46.187.158. The CIDR is 29 and the gateway is 255.46.187.152. I've installed a guest with ubuntuserver 12.04 x64, which was able to get and retrieve internet resources during installation, but now cannot reach anything nor can it be reached from anything. Its network configuration is: iface eth0 inet static address 255.46.187.153 netmask 255.255.255.224 broadcast 255.46.187.159 gateway 255.46.187.152 dns-nameservers <host provided nameservers> And is not able to ping google.com through DNS or direct IP, I can't ping the VM from the outside or the host. any ideas now?

  Read the article

• SOA 10g Developing a Simple Hello World Process

  - by [email protected]

  Softwares & Hardware Needed Intel Pentium D CPU 3 GHz, 2 GB RAM, Windows XP System ( Thats what i am using ) You could as well use Linux , but please choose High End RAM 10G SOA Suite from Oracle(TM) , Read Installation documents at www.Oracle.com J Developer 10.1.3.3 Official Documents at http://www.oracle.com/technology/products/ias/bpel/index.html java -version Java HotSpot(TM) Client VM (build 1.5.0_06-b05, mixed mode)BPEL Introduction - Developing a Simple Hello World Process  Synchronous BPEL Process      This Exercise focuses on developing a Synchronous Process, which mean you give input to the BPEL Process you get output immediately no waiting at all. The Objective of this exercise is to give input as name and it greets with Hello Appended by that name example, if I give input as "James" the BPEL process returns "Hello James". 1. Open the Oracle JDeveloper click on File -> New Application give the name "JamesApp" you can give your own name if it pleases you. Select the folder where you want to place the application. Click "OK" 2. Right Click on the "JamesApp" in the Application Navigator, Select New Menu. 3. Select "Projects" under "General" and "BPEL Process Project", click "OK" these steps remain same for all BPEL Projects 4. Project Setting Wizard Appears, Give the "Process Name" as "MyBPELProc" and Namespace as http://xmlns.james.com/ MyBPELProc, Select Template as "Synchronous BPEL Process click "Next" 5. Accept the input and output schema names as it is, click "Finish" 6. You would see the BPEL Process Designer, some of the folders such as Integration content and Resources are created and few more files 7. Assign Activity : Allows Assigning values to variables or copying values of one variable to another and also do some string manipulation or mathematical operations In the component palette at extreme right, select Process Activities from the drop down, and drag and drop "Assign" between "receive Input" and "replyOutput" 8. You can right click and edit the Assign activity and give any suitable name "AssignHello", 9. Select "Copy Operation" Tab create "Copy Operation" 10. In the From variables click on expression builder, select input under "input variable", Click on insert into expression bar, complete the concat syntax, Note to use "Ctrl+space bar" inside expression window to Auto Populate the expression as shown in the figure below. What we are actually doing here is concatenating the String "Hello ", with the variable value received through the variable named "input" 11. Observe that once an expression is completed the "To Variable" is assigned to a variable by name "result" 12. Finally the copy variable looks as below 13. It's the time to deploy, start the SOA Suite 14. Establish connection to the Server from JDeveloper, this can be done adding a New Application Server under Connection, give the server name, username and password and test connection. 15. Deploy the "MyBPELProc" to the "default domain" 16. http://localhost:8080/ allows connecting to SOA Suite web portal, click on "BPEL Control" , login with the username "oc4jadmin" password what ever you gave during installation 17. "MyBPELProc" is visisble under "Deployed BPEL Processes" in the "Dashboard" Tab, click on the it 18. Initiate tab open to accept input, enter data such as input is "James" click on "Post XML Button" 19. Click on Visual Flow 20. Click on receive Input , it shows "James" as input received 21. Click on reply Output, it shows "Hello James" so the BPEL process is successfully executed. 22. It may be worth seeing all the instance created everytime a BPEL process is executed by giving some inputs. Purge All button allows to delete all the unwanted previous instances of BPEL process, dont worry it wont delete the BPEL process itself :-) 23. It may also be some importance to understand the XSD File which holds input & output variable names & data types. 24. You could drag n drop variables as elements over sequence at the designer or directly edit the XML Source file. 

  Read the article

• Oracle Internet Directory 11gR1 11.1.1.6 Certified with E-Business Suite

  - by Elke Phelps (Oracle Development)

  Oracle E-Business Suite comes with native user authentication and management capabilities out-of-the-box. If you need more-advanced features, it's also possible to integrate it with Oracle Internet Directory and Oracle Single Sign-On or Oracle Access Manager, which allows you to link the E-Business Suite with third-party tools like Microsoft Active Directory, Windows Kerberos, and CA Netegrity SiteMinder.  For details about third-party integration architectures, see either of these article for EBS 11i and 12: In-Depth: Using Third-Party Identity Managers with E-Business Suite Release 12 In-Depth: Using Third-Party Identity Managers with the E-Business Suite Release 11i Oracle Internet Directory 11.1.1.6 is now certified with Oracle E-Business Suite Release 11i, 12.0 and 12.1.  OID 11.1.1.6 is part of Oracle Fusion Middleware 11g Release 1 Version 11.1.1.6.0, also known as FMW 11g Patchset 5.  Certified E-Business Suite releases are: EBS Release 11i 11.5.10.2 + ATG PH.H RUP 7 and higher EBS Release 12.0.6 and higher EBS Release 12.1.1 and higher Supported Configurations Oracle Internet Directory 11.1.1.5.0 can be integrated with two single sign-on solutions for EBS environments: Oracle Internet Directory and Directory Integration Platform from Fusion Middleware 11gR1 Patchset 5 (11.1.1.6.0) with Oracle Access Manager 10g (10.1.4.3) with an existing Oracle E-Business Suite system (Release 11i or 12.1.x). Oracle Internet Directory and Directory Integration Platform from Fusion Middleware 11gR1 Patchset 5 (11.1.1.6.0) with Oracle Access Manager 11gR1 (11.1.1.5) with an existing Oracle E-Business Suite system (Release 12.0.6 or higher or 12.1.x). Oracle Internet Directory (OID) and Directory Integration Platform (DIP) from Oracle Fusion Middleware 11gR1 Patchset 5  (11.1.1.6.0) with Oracle Single Sign-On Server and Oracle Delegated Administration Services Release 10g (10.1.4.3.0) with an existing Oracle E-Business Suite system (Release 11i, 12.0.6 or 12.1.x) Oracle Access Manager strongly recommended Oracle has two single sign-on solutions: Oracle Single Sign-On Server (OSSO) and Oracle Access Manager (OAM). Oracle strongly recommends that all new single sign-on implementations use Oracle Access Manager. Oracle Access Manager is the preferred solution going forward, and forms the basis of Oracle Fusion Middleware 11g. OSSO is no longer being actively developed and will not be ported to Oracle WebLogic Server. Platform certifications Oracle Internet Directory is certified to run on any operating system for which Oracle WebLogic Server 11g is certified. Refer to the Oracle Fusion Middleware 11g System Requirements for more details.For information on operating systems supported by Oracle Internet Directory and its components, refer to the Oracle Identity and Access Management 11gR1 certification matrix.Integration with Oracle Internet Directory involves components spanning several different suites of Oracle products. There are no restrictions on which platform any particular component may be installed so long as the platform is supported for that component.References Overview of Single Sign-On Integration Options for Oracle E-Business Suite Note 1388152.1 Using the Latest Oracle Internet Directory 11gR1 Patchset with Oracle Single Sign-on and Oracle E-Business Suite (Note 876539.1) Integrating Oracle E-Business Suite with Oracle Access Manager 11g using Oracle E-Business Suite AccessGate (Note 1309013.1) Integrating Oracle E-Business Suite with Oracle Access Manager 10g using Oracle E-Business Suite AccessGate (Note 975182.1) Migrating Oracle Single Sign-On 10gR3 to Oracle Access Manager 11g with Oracle E-Business Suite (Note 1304550.1) Oracle Fusion Middleware Download, Installation & Configuration Readme Oracle Fusion Middleware Installation Guide for Oracle Identity Management 11g Release 1 (11.1.1) (Part Number E12002-09) Oracle Fusion Middleware Upgrade Guide for Oracle Identity Management 11g Release 1 (11.1.1) (Part Number E10129-09) Oracle Fusion Middleware Upgrade Planning Guide 11g Release 1 (11.1.1) (Part Number E10125-06) Oracle Fusion Middleware Patching Guide 11g Release 1 (11.1.1) (Part Number E16793-12) Related Articles Understanding Options for Integrating Oracle Access Manager with E-Business Suite In-Depth: Using Third-Party Identity Managers with E-Business Suite Release 12 In-Depth: Using Third-Party Identity Managers with the E-Business Suite Release 11i Oracle Access Manager 10gR3 Certified with E-Business Suite Portal 11.1.1.4 Certified with E-Business Suite Discoverer 11.1.1.4 Certified with E-Business Suite

  Read the article

• [MISC GEEKERY] Support for Some Versions of Windows is Ending

  - by Matthew Guay

  Are you sticking with your older version of Windows instead of upgrading to Windows 7?  There’s no problem with that, but here’s a quick reminder to make sure you’re running the latest service pack to stay protected. Microsoft offers security updates and more throughout the lifetime of a version of Windows, and periodically they roll all the latest updates and improvements together into a service pack.  After a while, only computers running the latest service pack will still get updates to keep them safe. Recently, Microsoft has been warning that support is ending for Windows XP with Service Pack 2 and the release version of Windows Vista.  When support ends, you will not receive any new security updates for Windows.  You can continue to use your computer the same as before, but it may not be as secure and if new security issues are discovered they will not be updated. However, it’s easy to stay supported: simply install XP Service Pack 3 or Vista Service Pack 2, depending on your computer.  Here’s how to do that: Windows XP To install Windows XP Service Pack 3, you can either check Windows Update for updates, or simply download it from Microsoft at this link: Download XP Service Pack 3 Run the download (or if you’re updating from Windows Update the installer will automatically launch), and proceed just as you normally would when installing a program.  Your computer will have to reboot during the install, so make sure you’ve saved all your work and closed other programs before installing.   To check what service pack your computer is running, click Start, then right-click on the My Computer button and choose Properties. This will show you what version and service pack of Windows you are running, and in this screenshot we see this computer has be updated to Service Pack 3. Please Note:  The version of XP shipped with Windows XP Mode in Windows 7 comes preconfigured with Service Pack 3, and does not need updated.  Additionally, if your computer is running the 64 bit version of Windows XP, then Service Pack 2 is the latest service pack for your computer, and it is still supported. Windows Vista If your computer is running Windows Vista, you can install Service Pack 2 to stay up to date and supported.  Simply check Windows Update for Service Pack 2 if you haven’t installed it yet, or download the installer for your computer from the link below: 32 bit: Vista Service Pack 2 32-bit 64 bit: Vista Service Pack 2 64-bit Run the installer, and simply set it up as a normal program installation.  Do note that your computer will reboot during the installation, so make sure to save your work and close other programs before installing. To see what service pack your computer is running, click the Start orb, then right-click on the Computer button and select Properties. This will show what service pack and edition of Windows Vista your computer is running right at the top of the page. Conclusion Microsoft makes it easy to keep using your computer safely and securely even if you choose to keep using your older version of Windows.  By installing the latest service pack, you will make sure that your computer will be supported for years to come.  Windows 7 users, you don’t need to worry; no service has been released for it yet.  Stay tuned, and we’ll let you know when any new service packs are available. www.microsoft.com/EOS – End of Support Information from Microsoft Similar Articles Productive Geek Tips Remove Optional and Probably Unnecessary Windows Vista ComponentsRequesting Hotfixes from Microsoft the Easy WayUnderstanding Windows Vista Aero Glass RequirementsAdd Network Support to Windows Live MovieMakerCustomize the Manufacturer Support Info in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional OutSync will Sync Photos of your Friends on Facebook and Outlook Windows 7 Easter Theme YoWindoW, a real time weather screensaver Optimize your computer the Microsoft way Stormpulse provides slick, real time weather data Geek Parents – Did you try Parental Controls in Windows 7?

  Read the article

• OBIEE 11.1.1 - Introduction to OBIEE 11g Full Sample App

  - by user809526

  Isn't it nice to discover OBIEE 11g around a nice "How To" catalog of features? to observe OBI and Essbase relationships at work? to discover TimesTen? The OBIEE 11g Full Sample App (FSA) is a comprehensive collection of examples designed to demonstrate the latest Oracle BIEE 11g capabilities and design best practices: Enhanced visualizations as Geo-spacial maps and interactive dashboards, Action Framework,  BI Publisher, Scorecard and Strategy Management, Mobile style sheets, Semantic layer modeling, Multi-source federation, Integration with products such as Essbase, Oracle OLAP, ODM, TimesTen, ODI and more The FSA is intended to be comprehensive, it is big (see CAVEAT below). The FSA is not an Oracle product, it is a good will free deployment of OBIEE/Essbase designed to exemplify OBIEE features, infrastructure and security around the Fusion Middleware components. Its contents and code are distributed free for demonstrative purposes only. It is neither maintained nor supported by Oracle as a licensed product. The OBIEE Full Sample App is independent of the default Sample App that comes with the OBIEE product. BENEFITS The FSA helps as a demonstrator of OBIEE 11g best practices, a tutorial, an environment "Test & Scrap", a SR bench (regression, conflicts), a tuning bench, a quick ready made POC seed for projects, a security options environment, ... The FSA - Is organized around a catalog of functional features - Has been deployed over 1000 times, it should be stable RELEASE The Full Sample App (V107) is bound to OBIEE 11.1.1.5 and Essbase 11.1.2.1 (November 2011). The FSA release dates are independent of the Product GA date (OBIEE). In early December 2011, a new functional Patch (V110) is released. It is easily applied (in less than 15 mins) on top of OBIEE SampleApp 11.1.1.5 (V107). The patch (V110) includes additional functional examples:        1. Web Catalog Statistics Application: Provides detailed insight into your web catalog content, dormant catalog objects, webcat impact analysis for metadata changes and more        2. Data inflation Scripts: A set of simple SQL procedures to quickly inflate SampleApp Fact and Dimension data to millions of records in a few minutes        3. Public Content Extensions Framework: A patching framework for public examples and contributions leveraging SampleApp        4. Additional report examples (including bridge report, external chart integrations) and bug fixes DISTRIBUTION as VBox image (November 2011) The ready made VBox image is designed to run on Virtual Box. It can be converted to VMware (see another BLOG). 1/ http://www.oracle.com/technetwork/middleware/bi-foundation/obiee-samples-167534.html VBox Image Deployment Guide Sampleapp_v107_GA.ovf - VBox image key file The above http URL provides the user:password for the ftp URLs below. 2/ ftp://user:[email protected]/static/SampleAppV107/ 12 "7-zip" files Sampleapp_v107_GA_7_20.7z.001 -> .012 We recommend 7-zip file manager for unzipping (http://www.7-zip.org/). Select Unzip here option, it will create the contents under a directory named "SampleApp_10722". On Windows, it is important to download and save zip file under the root directory (e.g. C:\ or D:\) because of possible long pathnames. 3/ ftp://user:[email protected]/static/SampleAppV107/Unzipped_Version/ 4 files Sampleapp_v107_GA-disk[1234].vmdk Important note: Check the provided checksums (md5sum). Please do it! DISTRIBUTION as Installation files for existing OBI 11.1.1.5 (November 2011) http://www.oracle.com/technetwork/middleware/bi-foundation/obiee-samples-167534.html Install files Deployment Guide SampleApp_10722_1.zip - 198 MB CAVEAT Many computers have RAM chips problems that keep often silent ... until you manipulate big files. It is strongly advised you run some memory check program eg MEMTEST in GRUB boot manager. Running md5sum repeatedly onto the very same big file must be consistent [same result], else a hardware memory problem is suspected. For Virtual Box, you should most likely enable VT-X (Vanderpool) hardware virtualization in BIOS. A free disk space of 80 GB is required to perform safely the VBox image installation. A Virtual Machine of minimum 6 to 7 GB memory fits the needs of combining OBIEE and Essbase execution.

  Read the article

• SQL SERVER – Top 10 “Ease of Use” Features of expressor Studio

  - by pinaldave

  expressor Studio is new data integration platform that is being marketed as the most easy to use tool of its kind.  But “easy to use” can be a relative term – an expert can find a very complex system easy, but a beginner might be stumped.  A recent article online discussed exactly what makes expressor Studio so easy use, and here is my view on this subject. Simple Installation There is one pop-up for one .exe file, and nothing more.  You can’t get much simpler than this.  It is also in the familiar Windows design, so there should be no surprises. No 3rd party software dependency Have you ever tried to download software, only to be slowed down by the need to download a compatible system to run the program, and another to read the user manual, and so on?  expressor Studio was designed specifically to avoid this problem. Microsoft Office Like Ribbon Bar and Menus As mentioned before, everything is in the familiar Windows design, from the pop up windows to the tool bars and menus.  There should be no learning curve for using this program, or even simply trying to navigate around a new system. General Development Design Interface This software has been designed to be simple and straightforward.  Projects can be arranged in a simple “tree” design, that is totally collapsible and can easy be added to or “trimmed” with a click of a button.  It was meant to be logical and easy to follow. Integrated Contextual Help This is a fancy way of saying that you can practically yell “help!” if you do get stuck on something.  Solving a problem is as simple as highlighting and hitting F1 for contextual help. Visual Indicators and Messages Wouldn’t it be nice to know exactly where something has gone wrong before trying to complete a project.  expressor Studio has a built in system to catch mistakes and highlight them in a bright color, flash a warning message, and even disable functions before you can continue – and possibly lose hours of work. Property Inputs and Selectors Every operator will have a list of requirements that need to be filled in.  But don’t worry; you won’t have to make stuff up to fill in the boxes.  Each one will have a drop-down menu with options to choose from – but not too many as to be confusing. Connection Wizards Configuring connections can be the hardest part of a project.  But not with the expressor Studioconnection wizard.  A familiar, Windows-style menu will walk you through connections so quickly you’ll forget what trouble it used to be. Templates With large, complex projects, a majority of your time is often spent simply setting up the files and inputting data.  But expressor Studio allows you to create one file and then save it as a template, saving you hours of boring data input. Extension Manager Let’s say that you need a little more functionality or some new features on your program. A lot of software requires you to download complex plug-ins that need to be decompressed and installed.  However, expressor Studio has extended its system to an Extension Manager, which allows for quick and easy installation of the functionality you need, without the need to download and decompress. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQL Utility, T SQL, Technology

  Read the article

• SQL Server – SafePeak “Logon Trigger” Feature for Managing Data Access

  - by pinaldave

  Lately I received an interesting question about the abilities of SafePeak for SQL Server acceleration software: Q: “I would like to use SafePeak to make my CRM application faster. It is an application we bought from some vendor, after a while it became slow and we can’t reprogram it. SafePeak automated caching sounds like an easy and good solution for us. But, in my application there are many servers and different other applications services that address its main database, and some even change data, and I feel that there is a chance that some servers that during the connection process we may miss some. Is there a way to ensure that SafePeak will be aware of all connections to the SQL Server, so its cache will remain intact?” Interesting question, as I remember that SafePeak (http://www.safepeak.com/Product/SafePeak-Overview) likes that all traffic to the database will go thru it. I decided to check out the features of SafePeak latest version (2.1) and seek for an answer there. A: Indeed I found SafePeak has a feature they call “Logon Trigger” and is designed for that purpose. It is located in the user interface, under: Settings -> SQL instances management  ->  [your instance]  ->  [Logon Trigger] tab. From here you activate / deactivate it and control a white-list of enabled server IPs and Login names that SafePeak will ignore them. Click to Enlarge After activation of the “logon trigger” Safepeak server is notified by the SQL Server itself on each new opened connection. Safepeak monitors those connections and decides if there is something to do with them or not. On a typical installation SafePeak likes all application and users connections to go via SafePeak – this way it knows about data and schema updates immediately (real time). With activation of the safepeak “logon trigger”  a special CLR trigger is deployed on the SQL server and notifies Safepeak on any connection that has not arrived via SafePeak. In such cases Safepeak can act to clear and lock the cache or to ignore it. This feature enables to make sure SafePeak will be aware of all connections so SafePeak cache will maintain exactly correct all times. So even if a user, like a DBA will connect to the SQL Server not via SafePeak, SafePeak will know about it and take actions. The notification does not impact the work of that connection, the user or application still continue to do whatever they planned to do. Note: I found that activation of logon trigger in SafePeak requires that SafePeak SQL login will have the next permissions: 1) CONTROL SERVER; 2) VIEW SERVER STATE; 3) And the SQL Server instance is CLR enabled; Seeing SafePeak in action, I can say SafePeak brings fantastic resource for those who seek to get performance for SQL Server critical apps. SafePeak promises to accelerate SQL Server applications in just several hours of installation, automatic learning and some optimization configuration (no code changes!!!). If better application and database performance means better business to you – I suggest you to download and try SafePeak. The solution of SafePeak is indeed unique, and the questions I receive are very interesting. Have any more questions on SafePeak? Please leave your question as a comment and I will try to get an answer for you. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Calling XAI Inbound Services from Oracle BI Publisher

  - by ACShorten

  Note: This technique requires Oracle BI Publisher 1.1.3.4.1 which supports Service Complex Types. Web Services require credentials for authentication. Note: The deafults for the product installation are used in this article. If your site uses alternative values then substitute those alternatives where applicable. Note: Examples shown in this article are examples for illustrative purposes only. When building a report in Oracle BI Publisher it may be necessary to call an XAI Inbound Service to get information via the object rather than directly calling the database tables for various reasons: The CLOB fields used in the Object are accessible for a report. Note: CLOB fields cannot be used as criteria in the current release. Objects can take advantage of algorithms to format or calculate additional data that is not stored in the database directly. For example, Information format strings can automatically generated by the object which gives consistent information between a report and the online screens. To use this facility the following process must be performed: Ensure that the product group, cisusers by default, is enabled for the SPLServiceBean in the console. This allows BI Publisher access to call Web Services directly. To ensure this follow the instructions below: Logon to the Oracle WebLogic server console using an appropriate administrator account. By default the user system or weblogic is provided for this purpose. Navigate to the Security Realms section and select your configured realm. This is set to myrealm by default. In the Roles and Policies section, expand the SPLService section of the Deployments option to reveal the SPLServiceBean roles. If there is no role associated with the SPLServiceBean, create a new EJB role and specify the cisusers role, by default. For example:   Add a Role Condition to the role just created, with a Predicate List of Group and specify cisusers as the Group Argument Name. For example: Save all your changes. The XAI Inbound Services to be used by BI Publisher must be defined prior to using the interface. Refer to the XAI Best Practices (Doc Id: 942074.1) from My Oracle Support or via the online help for more information about this process. Inside BI Publisher create your report, according to the BI Publisher documentation. When specifying the dataset, under the Data Model Report option, specify the following to use an XAI Inbound Service as a data source: Parameter Comment Type Web Service Complex Type true Username Any valid user name within the product. This user MUST have security access to the objects referenced in the XAI Inbound Service Password Authentication password for Username Timeout Timeout, in seconds, set for the Web Service call. For example 60 seconds. WSDL URL Use the WSDL URL on the XAI Inbound Service definition as your WSDL URL. It will be in the following format by default:http://<host>:<port>/<server>/XAIApp/xaiserver/<service>?WSDLwhere: <host> - Host Name of Web Application Server <port> - Port allocated to Web Application Server for product access <server> - Server context for server <service> - XAI Inbound Service Name Note: For customers using secure transmission should substitute https instead of http and use the HTTPS port allocated to the product at installation time. Web Service Select the name of the service that shows in the drop-down menu. If no service name shows up, it means that Publisher could not establish a connection with the server or WSDL name provided in the above URL in order to get the service name. See BI Publisher server log for more information. Method Select the name of the Method that shows in the drop-down menu. A method name should show in the Method drop-down menu once the Web Service name is selected. For example: Additionally, filters can be used from the Web Service that can be generated, required or optional, from the WSDL in the Parameter List. For example:

  Read the article

• Is SugarCRM really adequate for custom development (or adequate at all)? [closed]

  - by dukeofgaming

  Have you used SugarCRM for custom development successfully?, if so, have you done it programmatically or through the Module Builder? Were you successful? If not, why? I used SugarCRM for a project about two years ago, I ran into errors from the very installation, having to hack the actual installation file to deploy the software in the server and other erros that I can't recall now. Two years after, I'm picking it up for a project once again. I'm feeling like I should have developed the whole thing from scratch myself. Some examples: I couldn't install it in the server (again). I had to install it locally, then copy the files and database over to the server and manually edit the config file. Constantly getting deployment errors from the module builder. One reason is SugarCRM keeps creating a record in the upgrade_history table for a file that does not exist, I keep deleting such record and it keeps coming back corrupt. I get other deployment errors, but have not figured them out. then I have to rollback all files and database to try again. I deleted a custom module with relationships, the relationships stayed in the other modules and cannot be deleted anymore, PHP warnings all over the place. Quick create for custom modules does not appear, hack needed. Its whole cache directory is a joke, permanent data/files are stored there. The module builder interface disappears required fields. Edit the wrong thing, module builder won't deploy again, then pray Quick Repair and/or Rebuild Relationships do the trick. My impression of SugarCRM now is that, regardless of its pretty exterior and apparent functionality, it is a very low quality piece of software. This even scared me more: http://amplicate.com/hate/sugarcrm; a quote: I wis this info had been available when I tried to implement it 2 years ago... I searched high and low and the only info I found was positive. Yes, it's a piece of crap. The community edition was full of bugs... nothing worked. Essentially I got fired for implementing it. I'm glad though, because now I work for myself, am much happier and make more money... so, I should really thank SugarCRM for sucking so much I guess! I figured that perhaps some of you have had similar experiences, and have either sticked with SugarCRM or moved on to another solution. I'm very interested in knowing what your resolutions were -or your current situations are- to make up my own mind, since the project I'm working on is long term and I'm feeling SugarCRM will be more an obstacle than an aid. After further failed attempts to continue using this software I continued to stumble upon dead-ends when using the module editor, I could only recover from this errors by using version control. We are now moving on to a custom implementation using Symfony; perhaps if we were using it with its out-of-the-box modules we would have sticked with it.

  Read the article

• Swap not available on System Monitor

  - by Zaki

  I had a swap partition of 1GB (RAM 1GB, Ubuntu 12.04 lts). Now swap is not shown on System Monitor neither can I hibernate my pc (sudo pm-hibernate). blkid output: /dev/sda1: UUID="B8B4FBB1B4FB706C" TYPE="ntfs" /dev/sda2: UUID="2ea7d608-2d89-4e41-9436-d05cb3ce8871" TYPE="swap" /dev/sda3: UUID="3219d03a-67e4-454b-8ce7-a27831846e35" TYPE="ext4" /dev/sda5: LABEL="Softwares" UUID="AC1CC3301CC2F47C" TYPE="ntfs" /dev/sda6: LABEL="Education" UUID="1E103E6C103E4B53" TYPE="ntfs" /dev/sda7: LABEL="Recreation" UUID="2CC8D181C8D149AA" TYPE="ntfs" /dev/sda8: LABEL="Miscellaneous" UUID="0274D6B174D6A727" TYPE="ntfs" /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda6 during installation UUID=3219d03a-67e4-454b-8ce7-a27831846e35 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=2ea7d608-2d89-4e41-9436-d05cb3ce8871 none swap sw 0 0 free -m total used free shared buffers cached Mem: 991 867 123 0 27 418 -/+ buffers/cache: 421 569 Swap: 0 0 0 cat /proc/swaps Filename Type Size Used Priority fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9f369f36 Device Boot Start End Blocks Id System /dev/sda1 * 63 31471334 15735636 7 HPFS/NTFS/exFAT /dev/sda2 31471616 33470447 999416 82 Linux swap / Solaris /dev/sda3 33472512 62539775 14533632 83 Linux /dev/sda4 62541045 312592769 125025862+ f W95 Ext'd (LBA) /dev/sda5 62541108 125066024 31262458+ 7 HPFS/NTFS/exFAT /dev/sda6 125066088 187591004 31262458+ 7 HPFS/NTFS/exFAT /dev/sda7 187591068 250115984 31262458+ 7 HPFS/NTFS/exFAT /dev/sda8 250116048 312576704 31230328+ 7 HPFS/NTFS/exFAT swapon --all swapon: /dev/sda2: swapon failed: Invalid argument dmesg | grep -A 5 -B 5 -i swap [ 9.487404] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 131645 [ 9.487413] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 131330 [ 9.487418] EXT4-fs (sda3): 16 orphan inodes deleted [ 9.487420] EXT4-fs (sda3): recovery complete [ 9.578600] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) [ 20.580539] Swap area shorter than signature indicates [ 20.588363] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 20.619443] udevd[330]: starting version 175 [ 20.649959] lp: driver loaded but no devices found [ 20.662972] [drm] Initialized drm 1.1.0 20060810 [ 20.675515] i915 0000:00:02.0: setting latency timer to 64 -- [ 72.288573] PM: thaw of drv:sr dev:3:0:0:0 complete after 178.143 msecs [ 72.288578] PM: thaw of drv:scsi_device dev:3:0:0:0 complete after 178.136 msecs [ 72.299677] PM: thaw of drv:scsi_device dev:2:0:0:0 complete after 189.270 msecs [ 72.309473] PM: thaw of devices complete after 202.763 msecs [ 72.309668] PM: writing image. [ 72.309670] PM: Cannot find swap device, try swapon -a. [ 72.309699] PM: Cannot get swap writer [ 72.329896] Restarting tasks ... done. [ 72.331777] PM: Basic memory bitmaps freed [ 72.331792] video LNXVIDEO:00: Restoring backlight state [ 72.420048] option1 ttyUSB0: option_instat_callback: error -84 [ 72.804047] option1 ttyUSB0: option_instat_callback: error -84 -- [ 145.960625] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 145.972036] sd 7:0:0:0: [sdb] Attached SCSI removable disk [ 172.430508] PPP BSD Compression module registered [ 172.455583] PPP Deflate Compression module registered [ 332.260789] type=1400 audit(1381814763.342:27): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=636 comm="cupsd" pid=636 comm="cupsd" capability=36 capname="block_suspend" [ 1913.030998] Swap area shorter than signature indicates [ 2022.530155] type=1400 audit(1381816453.610:28): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=636 comm="cupsd" pid=636 comm="cupsd" capability=36 capname="block_suspend" [ 4062.729509] Swap area shorter than signature indicates Please help. Thanks in advance. df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 14G 6.1G 7.0G 47% / udev 488M 4.0K 488M 1% /dev tmpfs 199M 868K 198M 1% /run none 5.0M 4.0K 5.0M 1% /run/lock none 496M 224K 496M 1% /run/shm

  Read the article

• NetworkManager Applet shows no networks

  - by Kkelk

  I am "the friend" referred to in the questions here and here. I decided to come and ask a question myself, as I can still not connect to the wireless network. I downloaded Keryx, as suggested here, and managed to download the necessary package and its dependencies. When I attempted to install the packages on Ubuntu using Keryx, Keryx just closed. Following this, I installed the packages manually using dpkg, and as far as I can tell, this was successful: kieran@ubuntu:~$ cd /host/wifi/Keryx/keryx/projects/Kieran/packages kieran@ubuntu:/host/wifi/Keryx/keryx/projects/Kieran/packages$ sudo dpkg -i *.deb [sudo] password for kieran: Selecting previously deselected package bcmwl-kernel-source. (Reading database ... 118296 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.60.48.36+bdcom-0ubuntu5_i386.deb) ... Selecting previously deselected package dkms. Unpacking dkms (from dkms_2.1.1.2-3ubuntu1.1_all.deb) ... Selecting previously deselected package fakeroot. Unpacking fakeroot (from fakeroot_1.14.4-1ubuntu1_i386.deb) ... Selecting previously deselected package linux-image. Unpacking linux-image (from linux-image_2.6.35.22.23_i386.deb) ... Selecting previously deselected package menu. Unpacking menu (from menu_2.1.44ubuntu1_i386.deb) ... Selecting previously deselected package patch. Unpacking patch (from patch_2.6-2ubuntu1_i386.deb) ... Setting up fakeroot (1.14.4-1ubuntu1) ... update-alternatives: using /usr/bin/fakeroot-sysv to provide /usr/bin/fakeroot (fakeroot) in auto mode. Setting up linux-image (2.6.35.22.23) ... Setting up menu (2.1.44ubuntu1) ... Setting up patch (2.6-2ubuntu1) ... Processing triggers for man-db ... Setting up dkms (2.1.1.2-3ubuntu1.1) ... Setting up bcmwl-kernel-source (5.60.48.36+bdcom-0ubuntu5) ... Loading new bcmwl-5.60.48.36+bdcom DKMS files... First Installation: checking all kernels... Building only for 2.6.35-22-generic Building for architecture i686 Building initial module for 2.6.35-22-generic Done. wl.ko: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/2.6.35-22-generic/updates/dkms/ depmod..... DKMS: install Completed. update-initramfs: deferring update (trigger activated) Processing triggers for install-info ... Processing triggers for doc-base ... Processing 31 changed 1 added doc-base file(s)... Registering documents with scrollkeeper... Processing triggers for menu ... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.35-22-generic Warning: No support for locale: en_GB.utf8 After rebooting, however, there were still no wireless networks in the NetworkManager Applet list. I opened the file /var/lib/NetworkManager/NetworkManager.state, and both NetworkEnabled and WirelessEnabled were set to True. While i'm very concious I may be asking a stupid question here, both my friend and I have nothing left to suggest, and as such - I would be very grateful for any answers as to how to get wireless working.

  Read the article

• disks not ready in array causes mdadm to force initramfs shell

  - by RaidPinata

  Okay, this is starting to get pretty frustrating. I've read most of the other answers on this site that have anything to do with this issue but I'm still not getting anywhere. I have a RAID 6 array with 10 devices and 1 spare. The OS is on a completely separate device. At boot only three of the 10 devices in the raid are available, the others become available later in the boot process. Currently, unless I go through initramfs I can't get the system to boot - it just hangs with a blank screen. When I do boot through recovery (initramfs), I get a message asking if I want to assemble the degraded array. If I say no and then exit initramfs the system boots fine and my array is mounted exactly where I intend it to. Here are the pertinent files as near as I can tell. Ask me if you want to see anything else. # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default (built-in), scan all partitions (/proc/partitions) and all # containers for MD superblocks. alternatively, specify devices to scan, using # wildcards if desired. #DEVICE partitions containers # auto-create devices with Debian standard permissions # CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR root # definitions of existing MD arrays # This file was auto-generated on Tue, 13 Nov 2012 13:50:41 -0700 # by mkconf $Id$ ARRAY /dev/md0 level=raid6 num-devices=10 metadata=1.2 spares=1 name=Craggenmore:data UUID=37eea980:24df7b7a:f11a1226:afaf53ae Here is fstab # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sdc2 during installation UUID=3fa1e73f-3d83-4afe-9415-6285d432c133 / ext4 errors=remount-ro 0 1 # swap was on /dev/sdc3 during installation UUID=c4988662-67f3-4069-a16e-db740e054727 none swap sw 0 0 # mount large raid device on /data /dev/md0 /data ext4 defaults,nofail,noatime,nobootwait 0 0 output of cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sda[0] sdd[10](S) sdl[9] sdk[8] sdj[7] sdi[6] sdh[5] sdg[4] sdf[3] sde[2] sdb[1] 23441080320 blocks super 1.2 level 6, 512k chunk, algorithm 2 [10/10] [UUUUUUUUUU] unused devices: <none> Here is the output of mdadm --detail --scan --verbose ARRAY /dev/md0 level=raid6 num-devices=10 metadata=1.2 spares=1 name=Craggenmore:data UUID=37eea980:24df7b7a:f11a1226:afaf53ae devices=/dev/sda,/dev/sdb,/dev/sde,/dev/sdf,/dev/sdg,/dev/sdh,/dev/sdi,/dev/sdj,/dev/sdk,/dev/sdl,/dev/sdd Please let me know if there is anything else you think might be useful in troubleshooting this... I just can't seem to figure out how to change the boot process so that mdadm waits until the drives are ready to build the array. Everything works just fine if the drives are given enough time to come online. edit: changed title to properly reflect situation

  Read the article

• Need help partitioning when reinstalling Ubuntu 14.04

  - by Chris M.

  I upgraded to 14.04 about a month ago on my HP Mini netbook (about 16 GB hard disk). A few days ago the system crashed (I don't know why but I was using internet at the time). When I restarted the computer, Ubuntu would not load. Instead, I got a message from the BIOS saying Reboot and Select proper Boot device or Insert Boot Media in selected Boot device and press a key I took this to mean that I needed to reinstall 14.04. When I try to reinstall Ubuntu from the USB stick, I choose "Erase disk and install Ubuntu" but then I get a message: Some of the partitions you created are too small. Please make the following partitions at least this large: / 3.3 GB If you do not go back to the partitioner and increase the size of these partitions, the installation may fail. At first I hit Continue to see if it would install anyway, and it gave the message: The attempt to mount a file system with type ext4 in SCSI1 (0,0,0), partition # 1 (sda) at / failed. You may resume partitioning from the partitioning menu. The second time I hit Go Back, and it took me to the following partitioning table: Device Type Mount Point Format Size Used System /dev/sda /dev/sda1 ext4 (checked) 3228 MB Unknown /dev/sda5 swap (not checked) 1063 MB Unknown + - Change New Partition Table... Revert Device for boot loader installation: /dev/sda ATA JM Loader 001 (4.3 GB) At this point I'm not sure what to do. I've never partitioned my hard drive before and I don't want to screw things up. (I'm not particularly tech savvy.) Can you instruct me what I should do. (P.S. I'm afraid the table might not appear as I typed it in.) Results from fdisk: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 4294 MB, 4294967296 bytes 255 heads, 63 sectors/track, 522 cylinders, total 8388608 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda doesn't contain a valid partition table Disk /dev/sdb: 7860 MB, 7860125696 bytes 155 heads, 31 sectors/track, 3194 cylinders, total 15351808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009a565 Device Boot Start End Blocks Id System /dev/sdb1 * 2768 15351807 7674520 b W95 FAT32 ubuntu@ubuntu:~$ Here is what it displays when I open the Disks utility (I tried the screenshot terminal command you suggested but it didn't seem to do anything): 4.3 GB Hard Disk /dev/sda Model: JM Loader 001 (01000001) Size: 4.3 GB (4,294,967,296 bytes) Serial Number: 01234123412341234 Assessment: SMART is not supported Volumes Size: 4.3 GB (4,294,967,296 bytes) Device: /dev/sda Contents: Unknown (There is a button in the utility that when you click it gives the following options: Format... Create Disk Image... Restore Disk Image... Benchmark but SMART Data & Self-Tests... is dimmed out) When I hit F9 Change Boot Device Order, it shows the hard drive as: SATA:PM-JM Loader 001 When I hit F10 to get me into the BIOS Setup Utility, under Diagnostic it shows: Primary Hard Disk Self Test Not Support NetworkManager Tool State: disconnected Device: eth0 Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 00:26:55:B0:7F:0C Capabilities: Carrier Detect: yes Wired Properties Carrier: off When I run command lshw -C network, I get: WARNING: you should run this program as super-user. *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:16 memory:feafc000-feafffff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: c0 serial: 00:26:55:b0:7f:0c capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:febc0000-febfffff ioport:ec80(size=128) WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• No Wireless Networks, BCM4313 [duplicate]

  - by TalonPlz

  This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

  Read the article

• Apache config that uses two document roots based on whether the requested resource exists in the first [closed]

  - by mattalexx

  Background I have a client site that consists of a CakePHP installation and a Magento installation: /web/example.com/ /web/example.com/app/ <== CakePHP /web/example.com/app/webroot/ <== DocumentRoot /web/example.com/app/webroot/store/ <== Magento /web/example.com/config/ <== Site-wide config /web/example.com/vendors/ <== Site-wide libraries The server runs Apache 2.2.3. The problem The whole company has FTP access and got used to clogging up the /web/example.com/, /web/example.com/app/webroot/, and /web/example.com/app/webroot/store/ directories with their own files. Sometimes these files need HTTP access and sometimes they don't. In any case, this mess makes my job harder when it comes to maintaining the site. Code merges, tarring the live code, etc, is very complicated and usually requires a bunch of filters. Abandoned solution At first, I thought I would set up a new subdomain on the same server, move all of their files there, and change their FTP chroot. But that wouldn't work for these reasons: Firstly, I have no idea (and neither do they remember) what marketing materials they've sent out that contain URLs to certain resources they've uploaded to the server, using the main domain, and also using abstract subdomains that use the main virtual host because it has ServerAlias *.example.com. So suddenly having them only use static.example.com isn't feasible. Secondly, The PHP scripts in their projects are potentially very non-portable. I want their files to stay in as similar an environment as they were built as I can. Also, I do not want to debug their code to make it portable. Half-baked solution After some thought, I decided to find a way to section off the actual website files into another directory that they would not touch. The company's uploaded files would stay where they were. This would ensure that I didn't break any of their projects that needed HTTP access. It would look something like this: /web/example.com/ <== A bunch of their files are in here /web/example.com/app/webroot/ <== 1st DocumentRoot; A bunch of their files are in here /web/example.com/app/webroot/store/ <== Some more are in here /web/example.com/site/ <== New dir; Contains only site files /web/example.com/site/app/ <== CakePHP /web/example.com/site/app/webroot/ <== 2nd DocumentRoot /web/example.com/site/app/webroot/store/ <== Magento /web/example.com/site/config/ <== Site-wide config /web/example.com/site/vendors/ <== Site-wide libraries After I made this change, I would not need to pay attention to anything except for the stuff within /web/example.com/site/ and my job would be a lot easier. I would be the only one changing stuff in there. So here's where the Apache magic would happen: I need an HTTP request to http://www.example.com/ to first use /web/example.com/app/webroot/ as the document root. If nothing is found (no miscellaneous uploaded company projects are found), try finding something within /web/example.com/site/app/webroot/. Another thing to keep in mind is, the site might have some problems if the $_SERVER['DOCUMENT_ROOT'] variable reads /web/example.com/app/webroot/ but the actual files are within /web/example.com/site/app/webroot/. It would be better if the DOCUMENT_ROOT environment variable could be /web/example.com/site/app/webroot/ for anything within the /web/example.com/site/app/webroot/ directory. Conclusion Is my half-baked solution possible with Apache 2.2.3? Is there a better way to solve this problem?

  Read the article

• Gnome-shell fails to load on 12.10

  - by Githlar

  I'm usually the one answering questions, but in this I'm throughly stumped! My Setup: Ubuntu 12.10 (Dist upgrade form 12.04) ATI M96 [Mobility Radeon HD 4650] Upon the first installation of 12.10 I had all kinds of issues getting the Legacy ATI drivers to install (I guess the source for the drivers isn't kosher with kernel 3.5). So, I added the repository ppa:makson96/fglrx - which has a version of the ATI source patched to work with kernel 3.5. After installation of fglrx-legacy from that PPA, gnome-shell and all my graphics work fine... until today. The Problem I unsuspended my computer today and the screen was black (not off, the black from the gnome lock screen). I'd move my mouse/hit a key and the background would flash and then it'd go back to black. Restarted via VT1 Logged into Gnome (gnome-shell) session, but no gnome-shell! Investigation: First, I went to VT1 and tried export DISPLAY=:0;gnome-shell --replace. It appeared to work fine, switch back to X and nothing. Went back to VT1 and saw this error message: JS ERROR: !!! Exception was: TypeError: Object 0x7fc748129c30 is not a subclass of (null), it's a xO JS ERROR: !!! message = '"Object 0x7fc748129c30 is not a subclass of (null), it's a xO"' JS ERROR: !!! fileName = '"/usr/share/gnome-shell/js/ui/tweener.js"' JS ERROR: !!! lineNumber = '218' JS ERROR: !!! stack = '"()@/usr/share/gnome-shell/js/ui/tweener.js:218 wrapper()@/usr/share/gjs-1.0/lang.js:204 ()@/usr/share/gjs-1.0/lang.js:145 ()@/usr/share/gjs-1.0/lang.js:239 init()@/usr/share/gnome-shell/js/ui/tweener.js:49 init()@/usr/share/gnome-shell/js/ui/environment.js:96 @<main>:1 "' Window manager warning: Log level 32: Execution of main.js threw exception: TypeError: Object 0x7fc748129c30 is not a subclass of (null), it's a xO Note: Everywhere it says "it's a xO", xO is actually garbled and changes every time (I'm thinking memory corruption?) This error is thrown by line 96 of /usr/share/gnome-shell/js/ui/environment.js: tweener.Init() Did a purge of fglrx-legacy, reboot, reinstall fglrx-legacy, reboot... same thing. Did a ppa-purge of ppa:gnome3-team/gnome3, and reinstalled gnome-shell and ubuntu-desktop from the standard repositores... same thing. I'm really at a loss here. I love gnome-shell and after using it for nearly a year now gnome classic just seems so archaic. Additional Information Apt log from the day I first suspended my machine (these are upgrades from the gnome3-team/gnome3 ppa and ubuntu-wine/ppa ppa): Start-Date: 2012-11-24 17:30:28 Commandline: aptdaemon role='role-commit-packages' sender=':1.618' Install: gkbd-capplet:amd64 (3.6.0-0ubuntu1), gnome-control-center-unity:amd64 (1.0-0ubuntu1~ubuntu12.10.1) Upgrade: nautilus:amd64 (3.6.2-0ubuntu0.1~quantal1, 3.6.3-0ubuntu2~ubuntu12.10.1), libgnome-control-center1:amd64 (3.4.2-0ubuntu19, 3.6.3-0ubuntu6~ubuntu12.10.1), wine1.5-i386:i386 (1.5.17-0ubuntu4, 1.5.18-0ubuntu1), wine1.5:amd64 (1.5.17-0ubuntu4, 1.5.18-0ubuntu1), gnome-settings-daemon:amd64 (3.4.2-0ubuntu14, 3.6.3-0ubuntu1~ubuntu12.10.1), gnome-control-center-data:amd64 (3.4.2-0ubuntu19, 3.6.3-0ubuntu6~ubuntu12.10.1), gnome-accessibility-themes:amd64 (3.6.0.2-0ubuntu1, 3.6.2-0ubuntu2~ubuntu12.10.1), gnome-themes-standard:amd64 (3.6.0.2-0ubuntu1, 3.6.2-0ubuntu2~ubuntu12.10.1), wine1.5-amd64:amd64 (1.5.17-0ubuntu4, 1.5.18-0ubuntu1), nautilus-data:amd64 (3.6.2-0ubuntu0.1~quantal1, 3.6.3-0ubuntu2~ubuntu12.10.1), gnome-control-center:amd64 (3.4.2-0ubuntu19, 3.6.3-0ubuntu6~ubuntu12.10.1), libnautilus-extension1a:amd64 (3.6.2-0ubuntu0.1~quantal1, 3.6.3-0ubuntu2~ubuntu12.10.1) End-Date: 2012-11-24 17:31:32 fglrxinfo (driver appears to be working): display: :0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: ATI Mobility Radeon HD 4650 OpenGL version string: 3.3.11653 Compatibility Profile Context Does anybody have any further ideas?

  Read the article

• Failed to unmount partitions

  - by msknapp

  I'm trying to install ubuntu from a pen drive. I have windows 7 installed already and want to keep that installation. I have a 3TB drive that has one 2TB partition on it, so the last 1TB is completely unused, which is where I want to install ubuntu. I started ubuntu in "try ubuntu" mode and then opened gparted, and then deleted the unused partition for the last third of my drive, then tried to install ubuntu. During the install, it asked me if I wanted to unmount the drives I already have The installer has detected that the following disks have mounted partitions: /dev/sda, /dev/sdb Do you want the installer to try to unmount the partitions on these disks before continuing? If you leave them mounted, you will not be able to create, delete, or resize partitions on these disks, but you may be able to install to existing partitions there. No, Yes I said no because I don't want to lose my windows 7 installation, nor any of that data. I wonder, if I had said yes above, would I have lost all the data on those drives? Anyways, I hit no and continued. I chose to install ubuntu alongside windows 7, and hit continue. A few minutes passed when this popup appeared: Failed to unmount partitions The installer needs to commit changes to partition tables, but cannot do so because the partitions on the following mount points could not be unmounted: /media/ubuntu/Three\ Terabyte Drive Terabyte\ DriveDrive Please close any applications using these mount points. Would you like the installer to try to unmount these partitions again? Go Back, Continue Why is this not working? What am I supposed to do? ========== Update: I went ahead and said yes, it can unmount those partitions. It finished installing Ubuntu, but now when i start my machine it just takes me to the grub rescue prompt. Seems like it broke something. What can I do now? =============== Results of fdisk -l: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00027e14 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 976771071 488282112 7 HPFS/NTFS/exFAT WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdb: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 4294967295 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. Disk /dev/sdc: 16.0 GB, 16008609792 bytes 255 heads, 63 sectors/track, 1946 cylinders, total 31266816 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 * 32 31266815 15633392 c W95 FAT32 (LBA) Disk /dev/sdd: 999.5 GB, 999501594624 bytes 255 heads, 63 sectors/track, 121515 cylinders, total 1952151552 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002ae3f Device Boot Start End Blocks Id System /dev/sdd1 2048 1952151551 976074752 7 HPFS/NTFS/exFAT

  Read the article

• Using Private Extension Galleries in Visual Studio 2012

  - by Jakob Ehn

  Note: The installer and the complete source code is available over at CodePlex at the following location: http://inmetavsgallery.codeplex.com   Extensions and addins are everywhere in the Visual Studio ALM ecosystem! Microsoft releases new cool features in the form of extensions and the list of 3rd party extensions that plug into Visual Studio just keeps growing. One of the nice things about the VSIX extensions is how they are deployed. Microsoft hosts a public Visual Studio Gallery where you can upload extensions and make them available to the rest of the community. Visual Studio checks for updates to the installed extensions when you start Visual Studio, and installing/updating the extensions is fast since it is only a matter of extracting the files within the VSIX package to the local extension folder. But for custom, enterprise-specific extensions, you don’t want to publish them online to the whole world, but you still want an easy way to distribute them to your developers and partners. This is where Private Extension Galleries come into play. In Visual Studio 2012, it is now possible to add custom extensions galleries that can point to any URL, as long as that URL returns the expected content of course (see below).Registering a new gallery in Visual Studio is easy, but there is very little documentation on how to actually host the gallery. Visual Studio galleries uses Atom Feed XML as the protocol for delivering new and updated versions of the extensions. This MSDN page describes how to create a static XML file that returns the information about your extensions. This approach works, but require manual updates of that file every time you want to deploy an update of the extension. Wouldn’t it be nice with a web service that takes care of this for you, that just lets you drop a new version of your VSIX file and have it automatically detect the new version and produce the correct Atom Feed XML? Well search no more, this is exactly what the Inmeta Visual Studio Gallery Service does for you :-) Here you can see that in addition to the standard Online galleries there is an Inmeta Gallery that contains two extensions (our WIX templates and our custom TFS Checkin Policies). These can be installed/updated i the same way as extensions from the public Visual Studio Gallery. Installing the Service Download the installler (Inmeta.VSGalleryService.Install.msi) for the service and run it. The installation is straight forward, just select web site, application pool and (optional) a virtual directory where you want to install the service.   Note: If you want to run it in the web site root, just leave the application name blank Press Next and finish the installer. Open web.config in a text editor and locate the the <applicationSettings> element Edit the following setting values: FeedTitle This is the name that is shown if you browse to the service using a browser. Not used by Visual Studio BaseURI When Visual Studio downloads the extension, it will be given this URI + the name of the extension that you selected. This value should be on the following format: http://SERVER/[VDIR]/gallery/extension/ VSIXAbsolutePath This is the path where you will deploy your extensions. This can be a local folder or a remote share. You just need to make sure that the application pool identity account has read permissions in this folder Save web.config to finish the installation Open a browser and enter the URL to the service. It should show an empty Feed page:   Adding the Private Gallery in Visual Studio 2012 Now you need to add the gallery in Visual Studio. This is very easy and is done as follows: Go to Tools –> Options and select Environment –> Extensions and Updates Press Add to add a new gallery Enter a descriptive name, and add the URL that points to the web site/virtual directory where you installed the service in the previous step   Press OK to save the settings. Deploying an Extension This one is easy: Just drop the file in the designated folder! :-)  If it is a new version of an existing extension, the developers will be notified in the same way as for extensions from the public Visual Studio gallery: I hope that you will find this sever useful, please contact me if you have questions or suggestions for improvements!

  Read the article

• cannot install firmware-b43-installer

  - by unknown

  output i get when installing the installArchives() failed: Preconfiguring packages ... Preconfiguring packages ... Preconfiguring packages ... Selecting previously deselected package menu. (Reading database ... (Reading database ... 5% (Reading database ... 10% (Reading database ... 15% (Reading database ... 20% (Reading database ... 25% (Reading database ... 30% (Reading database ... 35% (Reading database ... 40% (Reading database ... 45% (Reading database ... 50% (Reading database ... 55% (Reading database ... 60% (Reading database ... 65% (Reading database ... 70% (Reading database ... 75% (Reading database ... 80% (Reading database ... 85% (Reading database ... 90% (Reading database ... 95% (Reading database ... 100% (Reading database ... 216125 files and directories currently installed.) Unpacking menu (from .../menu_2.1.44ubuntu1_i386.deb) ... Selecting previously deselected package wifi-radar. Unpacking wifi-radar (from .../wifi-radar_2.0.s05-1.2_all.deb) ... Processing triggers for man-db ... Processing triggers for install-info ... Processing triggers for doc-base ... Processing 1 added doc-base file(s)... Registering documents with scrollkeeper... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for python-gmenu ... Rebuilding /usr/share/applications/desktop.en_US.UTF8.cache... Processing triggers for python-support ... Setting up firmware-b43-installer (4.150.10.5-5) ... --2012-10-26 08:51:30-- http://mirror2.openwrt.org/sources/broadcom-wl-4.150.10.5.tar.bz2 Resolving mirror2.openwrt.org... 46.4.11.11 Connecting to mirror2.openwrt.org|46.4.11.11|:80... failed: Connection refused. dpkg: error processing firmware-b43-installer (--configure): subprocess installed post-installation script returned error exit status 4 No apport report written because MaxReports is reached already Setting up menu (2.1.44ubuntu1) ... Processing triggers for menu ... Setting up wifi-radar (2.0.s05-1.2) ... Processing triggers for menu ... Errors were encountered while processing: firmware-b43-installer Setting up firmware-b43-installer (4.150.10.5-5) ... --2012-10-26 08:51:33-- http://mirror2.openwrt.org/sources/broadcom-wl-4.150.10.5.tar.bz2 Resolving mirror2.openwrt.org... 46.4.11.11 Connecting to mirror2.openwrt.org|46.4.11.11|:80... failed: Connection refused. dpkg: error processing firmware-b43-installer (--configure): subprocess installed post-installation script returned error exit status 4 same thing occurs when i try to install any of the wireless application. All other software installs and the same error when trying to install firmware. I tried to go the link(http://mirror2.openwrt.org/sources/broadcom-wl-4.150.10.5.tar.bz2) and download the package but found no make file found in his package. please help me.

  Read the article

• FileNotFoundException when running WiX CustomAction with COMAdmin interop

  - by dabcabc

  I am trying to create a WiX custom action which will allow me to shutdown and clear down a COM+ package as part of an upgrade installation, or create and configure a new COM+ package as part of the initial installation. I previously had this running as a CustomAction within a standard Visual Studio MSI but this only allows the custom action to be executed after the files have been copied - which will fail as the package will still be running. The COMAdmin.dll has been added as a reference to the CustomAction project and is set CopyLocal=true. In the bin folder for the custom action project the Interop.COMAdmin.dll is present. The answer to this question seems to suggest that it should work. I am getting the following exception within the MSI log when trying to install: MSI (s) (C4:04) [10:40:34:205]: Invoking remote custom action. DLL: C:\WINDOWS\Installer\MSI119.tmp, Entrypoint: BeforeInstall SFXCA: Extracting custom action to temporary directory: C:\WINDOWS\Installer\MSI119.tmp-\ SFXCA: Binding to CLR version v2.0.50727 Calling custom action MyCustomAction!MyCustomAction.CustomActions.BeforeInstall Exception thrown by custom action: System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.IO.FileNotFoundException: Could not load file or assembly 'Interop.COMAdmin, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null' or one of its dependencies. The system cannot find the file specified. File name: 'Interop.COMAdmin, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null' at MyCustomAction.CustomActions.BeforeInstall(Session session) WRN: Assembly binding logging is turned OFF. To enable assembly bind failure logging, set the registry value (DWORD) to 1. Note: There is some performance penalty associated with assembly bind failure logging. To turn this feature off, remove the registry value . --- End of inner exception stack trace --- at System.RuntimeMethodHandle._InvokeMethodFast(Object target, Object arguments, SignatureStruct& sig, MethodAttributes methodAttributes, RuntimeTypeHandle typeOwner) at System.RuntimeMethodHandle.InvokeMethodFast(Object target, Object arguments, Signature sig, MethodAttributes methodAttributes, RuntimeTypeHandle typeOwner) at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object parameters, CultureInfo culture, Boolean skipVisibilityChecks) at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object parameters, CultureInfo culture) at Microsoft.Deployment.WindowsInstaller.CustomActionProxy.InvokeCustomAction(Int32 sessionHandle, String entryPoint, IntPtr remotingDelegatePtr)

  Read the article

• how to run pentaho bi-server on CentOS 6.2 and PostgreSQL 8.4.x?

  - by gtludwig

  I'm trying to run an instance of Pentaho's bi-server-ce on a freshly installed CentOS 6.2 using PostgreSQL 8.4.x. I've installed a JDK 1.6 instance and it is working. Also I've a tomcat 6.0.35 instance where I run a few apps. I'd like bi-server to be one of many apps I run on this tomcat. Regarding Pentaho's Bi-Server installation I'm following the guide from https://docs.google.com/document/edit?id=1OnvHYsa-nYgwP8bjqRqjP5Vy-gLI5xomOHZtOvA00Ns#bookmark=id.2d95068df264 I've adapted the steps to my local installation, but still I can't start the server. I get the following error when trying to start the pentaho app: Jul 23, 2012 12:00:30 PM org.apache.catalina.startup.ContextConfig validateSecurityRoles INFO: WARNING: Security role name PENTAHO_ADMIN used in an without being defined in a 12:00:31,953 ERROR [JDBCExceptionReporter] FATAL: Ident authentication failed for user "hibuser" 12:00:32,222 ERROR [JDBCExceptionReporter] FATAL: Ident authentication failed for user "hibuser" 12:00:32,223 ERROR [SchemaUpdate] could not get database metadata org.postgresql.util.PSQLException: FATAL: Ident authentication failed for user "hibuser" (...) I do believe it's something related to the postgre user hibuser, but all settings on all files seem to be OK. Also I've a copy of the postgresql jar driver on tomcat's /lib folder. I've run out of ideas, can anyone throw me light here?

  Read the article

• Android: SharedPreference: Defaults not set at startup...

  - by Allan

  I have Listpreferences in my app. They don't appear to be setting to their defaults right after installation - they appear to be null. I'm trying to figure out why my default preferences are not being set right after installation. In my main code I have: SharedPreferences sp = PreferenceManager.getDefaultSharedPreferences(this); InUnits = sp.getString("List1", "defValue"); InAngs = sp.getString("List2", "defValue"); OutUnits = sp.getString("List3", "defValue"); OutAngs = sp.getString("List4", "defValue"); Right after the above code executes, each variable contains "defValue" instead of the actual values I have assigned in my ListPreference below. My preference xml file is called, "settings.xml". Here's what one of the ListPreferences there looks like: <ListPreference android:key="List1" android:title="Input: Alph" android:summary="Choose Alph or Ralph" android:entries="@array/inputAlph" android:entryValues="@array/input_Alph_codes" android:dialogTitle="Input Alph" android:defaultValue="ININ"/> Here's what some of my strings.xml file looks like: <string-array name="inputUnits"> <item>Alph</item> <item>Ralph</item> </string-array> <string-array name="input_Alph_codes"> <item>ININ</item> <item>INMM</item> </string-array> When I go to menu, and then settings, I can see my defaults checked (radiobuttoned). Then when I go back from the settings menu to my main screen - all is well - for life! ...then each var above is assigned the proper default value. This only happens when I first install my app on the phone. After I go to the settings screen once and then right out of it, the app is fine and accepts any setting changes. By the way, as you can see, "List1" is the android:key within a file called settings.xml in my res/xml folder.

  Read the article

• How do I make the 32-bit Perl read the 64-bit Windows registry?

  - by Santhosh

  I have a 32-bit perl installer. Using this I need to be able to install and uninstall both 32- and 64-bit applications. Installing 32- and 64-bit is fine. Uninstalling 32-bit is also ok. However, I have a problem while uninstalling 64-bit applications. The application just knows the name of the application as seen in Add Remove programs in control panel. For instance it could be "Winzip 14.0" which is the display name for Winzip. I use the following approach for uninstallation : I traverse to HKLM/Software/Microsoft/Windows/CurrentVersion/Uninstall and parse the keys present there to see if Winzip is matching. If so i get the uninstall string from there. my $register = "SOFTWARE\\Microsoft\\Windows\\CurrentVersion\\Uninstall"; $HKEY_LOCAL_MACHINE->Open($register,$hKey)|| die $!; #Then parse all the nodes and fetch the uninstall string If the application is a 64-bit installation, then the uninstallation information will reside in HKLM/Software/Microsoft/Windows/CurrentVersion/Uninstall. However the above given perl installer code is trying to read from HKLM/Software/WOW6432Node/Microsoft/Windows/CurrentVersion/Uninstall and it does not find the installation there. So how do I make the Perl code running in a 32_bit process to read the registry value found in 64-bit hive? I am aware of the RegOpenKey() API that takes KEY_WOW64_64KEY parameter. But since it is a Windows API, I dont know if that will help. Even then, is there any other alternative?

  Read the article

< Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >