Search Results

Search found 15499 results on 620 pages for 'non obvious'.

Page 365/620 | < Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• logrotate deletes all maillogs older than one day

  - by shadyabhi

  I see only two files maillog and maillog.1 in /var/log. grepping for maillog in logrotate.d directory gives three files that have a mention of maillog. syslog /var/log/messages /var/log/secure /var/log/maillog /var/log/spooler /var/log/boot.log /var/log/cron { #/var/log/messages /var/log/secure /var/log/spooler /var/log/boot.log /var/log/cron { daily sharedscripts postrotate /bin/kill -HUP `cat /var/run/syslogd.pid 2> /dev/null` 2> /dev/null || true /bin/kill -HUP `cat /var/run/rsyslogd.pid 2> /dev/null` 2> /dev/null || true endscript } syslog-ng /var/log/messages /var/log/secure /var/log/maillog /var/log/spooler /var/log/boot.log /var/log/cron /var/log/kern.log /var/log/kern { sharedscripts postrotate /bin/kill -HUP `cat /var/run/syslogd.pid 2> /dev/null` 2> /dev/null || true /bin/kill -HUP `cat /var/run/rsyslogd.pid 2> /dev/null` 2> /dev/null || true endscript } and maillog. /var/log/maillog { daily compress # rotate 365 rotate 14 sharedscripts postrotate /bin/kill -HUP `cat /var/run/syslogd.pid 2> /dev/null` 2> /dev/null || true /bin/kill -HUP `cat /var/run/rsyslogd.pid 2> /dev/null` 2> /dev/null || true endscript } I am new to logrotate so may be I am missing something obvious. What can be the issue? The setup was already done when I started managing the server so I don't also know as do why do I have 3 mentions for maillog in logrotate.

  Read the article

• Recommended drive encryption solution

  - by Chris Driver

  Hello, I will soon be purchasing a number of laptops running Windows 7 for our mobile staff. Due to the nature of our business I will need drive encryption. Windows BitLocker seems the obvious choice, but it looks like I need to purchase either Windows 7 Enterprise or Ultimate editions to get it. Can anyone offer suggestions on the best course of action: a) Use BitLocker, bite the bullet and pay to upgrade to Enterprise/Ultimate b) Pay for another 3rd party drive encryption product that is cheaper (suggestions appreciated) c) Use a free drive encryption product such as TrueCrypt Ideally I am also interested in 'real world' experience from people who are using drive encryption software and any pitfalls to look out for. Many thanks in advance... UPDATE Decided to go with TrueCrypt for the following reasons: a) The product has a good track record b) I am not managing a large quantity of laptops so integration with Active Directory, Management consoles etc is not a huge benefit c) Although eks did make a good point about Evil Maid (EM) attacks, our data is not that desirable to consider it a major factor d) The cost (free) is a big plus but not the primary motivator The next problem I face is imaging (Acronis/Ghost/..) encrypted drives will not work unless I perform sector-by-sector imaging. That means an 80Gb encrypted partition creates an 80Gb image file :(

  Read the article

• Do background processes get a SIGHUP when logging off?

  - by Massimo

  This is a followup to this question. I've run some more tests; looks like it really doesn't matter if this is done at the physical console or via SSH, neither does this happen only with SCP; I also tested it with cat /dev/zero > /dev/null. The behaviour is exactly the same: Start a process in the background using & (or put it in background after it's started using CTRL-Z and bg); this is done without using nohup. Log off. Log on again. The process is still there, running happily, and is now a direct child of init. I can confirm both SCP and CAT quits immediately if sent a SIGHUP; I tested this using kill -HUP. So, it really looks like SIGHUP is not sent upon logoff, at least to background processes (can't test with a foreground one for obvious reasons). This happened to me initially with the service console of VMware ESX 3.5 (which is based on RedHat), but I was able to replicate it exactly on CentOS 5.4. The question is, again: shouldn't a SIGHUP be sent to processes, even if they're running in background, upon logging off? Why is this not happening? Edit I checked with strace, as per Kyle's answer. As I was expecting, the process doesn't get any signal when logging off from the shell where it was launched. This happens both when using the server's console and via SSH.

  Read the article

• What can prevent a Server 2008 machine accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. I don't think it is this because we have a 2003 Server machine behind a different hardware firewall and that one works fine. What on earth is left?!

  Read the article

• Linux NFS create mask and force user equivalent

  - by Mike

  I have two Linux servers: fileserver Debian 5.0.3 (2.6.26-2-686) Samba version 3.4.2 apache Ubuntu 10.04 LTS (2.6.32-23-generic) Apache 2.2.14 I have a number of Samba shares on fileserver so that I can access files from Windows PCs. I am also exporting /data/www-data to the apache server, where I have it mounted as /var/www. The setup is okay, except for when I come to create files on the NFS mount. I end up with files that cannot be read by Apache, or which cannot be modified by other users on my system. With Samba, I can specify force user, force group, create mask and directory mask, and this ensures that all files are created with suitable permissions for my Apache web server. I can't find a way to do this with NFS. Is there a way to force permissions and ownership with NFS - am I missing something obvious? Although I've spent quite a bit of time with Linux, and am weaning myself off Windows, I still haven't quite got to grip with Linux permissions... If this is not the right way to do things, I am open to alternative suggestions.

  Read the article

• Getting Started in SuSE as an Ubuntu User

  - by Subhamoy Sengupta

  I am not a Linux newbie, but haven't touched SuSE in a very very long time (last time I tried it, it was SuSE 7!). Finally now I felt like giving it a try, and many things seem strange or unnecessarily complex. I have a series of questions. How do I ensure that my packages are uptodate? It sounds silly, but I tried the obvious methods already. I have disabled the default repositories that show up when you do zypper lr, and added Tumbleweed and packman repositories (Essentials, Multimedia, Extra). Then I did a sudo zypper ref --force and then sudo zypper dup, and it tells me many dependencies are not met. I have already added solder.allowVendorChange=true to /etc/zypp/zypp.conf, so it should not care which repository the latest versions are in, and just upgrade to it. Even when I chose to skip the packages with unmet dependencies, and seemed like quite a bit happened in the background, I opened Firefox afterwards and the version was 7! I am guessing things did not go as expected. But of course this is not a problem with SuSE, but I am not understanding the system right. How do I do it right? When I start typing arguments of a command, for example sudo zypper install, when I type sudo zypper ins and keep hitting TAB, nothing happens! It always worked in Ubuntu and I feel very uneasy with this. Is this how SuSE is supposed to be? When I try to install something, and I start writing its name, even though the package exists and I am sure of it, hitting TAB does not autocomplete it. This is also quite inconvenient. Why is it not happening? There are many things in SuSE that are really great, and I think I will stay with it and not go back to Ubuntu once I settle these very rudimentary issues. But right now they are giving me a lot of grief! Please help!

  Read the article

• Upgrading memory in a laptop

  - by ulidtko

  I'm a bit confused about all the memory types and various bus frequencies of modern consumer PCs. Requesting expert help on the subject. So far I'm confident that: I have an Asus X51L laptop with an unknown set of configuration options. The CPU in there supports PAE, so I still have a chance to extend the memory beyond 3GiB; and the upper limit of the system is 8GiB. (?) The laptop has two SODIMM slots, one of which is occupied by a 2GiB bank, and the other one is empty. dmidecode and lshw tools consistently state 533 Mhz frequency of the bank. The last one confuses me the most. I failed to find out characteristics of the northbridge in this laptop, and still can't figure out what DDR2 to seek for. Is it DDR2-1066? Or, rather, PC2-8500/PC2-8600? Wouldn't a DDR2-800 bank harm the system's performance? Which kind of modules should I look up in stores? Update: I have bought a 2 GiB DDR2-800 SODIMM, and it seams that the system can't handle 4 GiB of memory. When installed by itself in either slot, both new and old bank (which btw happens to be marked GDDR2-677) work just perfectly; i.e. any configuration resulting in 2 GiB works. When both banks are installed though (totalling in 4 GiB), the memcheck86 tool produces horrible artifacts and crashes, and system reboots; an Ubuntu system can be started and even logged into a Unity session, but the system reboots too in this case from even a minor RAM load. So it's pretty obvious to me now that this laptop doesn't support 4 GiB of RAM or more.

  Read the article

• Nginx + WordPress + HHVM: Why isn't Batcache working? Would Varnish help even more?

  - by javipas

  I've heard great things about HHVM, so I've setup a copy of WordPress blog (on another domain) with Nginx (with the Pagespeed module) and HHVM. Right now the benefits are obvious: on the same config, load times are between two and three times faster. I'm trying to speed up things a little bit, and I've also installed Memcached and Batcache. I've installed the memcached package, copied object-cache.php (Pastebin) onto the root folder of the WordPress blog, and after that I've installed the Batcache plugin and copied the advanced-cache.php (Pastebin) file onto the wp-content folder. Also, I've included the line define('WP_CACHE', true); in the wp-config.php file. It seems it doesn't work, though. If I quickly reload the page several times Batcache should show the cached page, but it doesn't. It's easy to check that by reloading (Cmd+R on Chrome on OS X) the page several times and then viewing the page's code. Under the <head> section I should see some batcache stats, but they aren't there. I wonder if someone could give me some hint on this. On a side note, I don't know if I could add some other component in order to help the performance be even better. I'm thing about Varnish, but I'm not sure if it's just useless and it's just another way to the same I'm currently doing. Any other component there? (I'll test CDN for images, minifying js, etc and some other tricks as well, but I'm talking from the server perspective).

  Read the article

• What format should I convert my iTunes Videos to?

  - by Aequitarum Custos

  Recently got Daniusoft Media Converter, and was about to strip the DRM off my iTunes library, then I found I had a huge decision to make. Converting my music seems obvious, to MP3, however the video formats, I'm at a loss on. It has "optimized" formats for all types of video players such as iPhone, Zune, Droid (which I own), and just a huge list! I bought several seasons of House and a few movies, though I don't know which format would be optimal to not lose quality. While I love my Droid, I have no intention on watching full episodes or movies on it, and I have a feeling that would reduce quality. One of the options sections is HD Video, and it has HD MPEG-4 Video (*.mp4). That one seems like it would be the best format to convert to without losing quality, but again, I'm unsure. Has anyone used this software, or have general expertise in video formats to give a recommendation on what file format I should convert my videos to? Format requirements: No loss in quality Portability would be ideal (as in, will play on my Windows and potentially MAC, and streamable to a bigscreen).

  Read the article

• VPN into multiple LAN Subnets

  - by Rain

  I need to figure out a way to allow access to two LAN subnets on a SonicWall NSA 220 through the built-in SonicWall GlobalVPN server. I've Googled and tried everything I can think of, but nothing has worked. The SonicWall NSA management web interface is also very unorganized; I'm probably missing something simple/obvious. There are two networks, called Network A and Network B for simplicity, with two different subnets. A SonicWall NSA 220 is the router/firewall/DHCP Server for Network A, which is plugged into the X2 port. Some other router is the router/firewall/DHCP server for Network B. Both of these networks need to be managed through a VPN connection. I setup the X3 interface on the SonicWall to have a static IP in the Network B subnet and plugged it in. Network A and Network B should not be able to access each other, which appears the be the default configuration. I then configured and enabled VPN. The SonicWall currently has the X1 interface setup with a subnet of 192.168.1.0/24 with a DHCP Server enabled, although it is not plugged in. When I VPN into the SonicWall, I get an IP address supplied by the DHCP Server on the X1 interface and I can access Network A remotely although I do not have access to Network B. How can I allow access to both Network A and Network B to VPN clients although keep devices on Network B from accessing Network A and vice-versa. Is there some way to create a VPN-only subnet (something like 10.100.0.0/24) on the SonicWall that can access Network A and Network B without changing the current network configuration or allowing devices on both netorks "see" each other? How would I go about setting this up? Diagram of the network: (Hopefully this kind of helps) WAN1 WAN2 | | [ SonicWall NSA 220 ]-(X3)-----------------[ Router 2 ] | | (X2) 192.168.2.0/24 10.1.1.0/24 Any help would be greatly appriciated!

  Read the article

• hyper-v cluster behavior when losing network connectivity

  - by ChristopheD

  Setup: (rather new) Hyper-V R2 cluster with 2 nodes (in failover configuration). Fysical host OS: Windows Server 2008. About eight VM's (mixed: Windows Server 2008 and Linux) Yesterday we had a power outage of about 15 minutes. Our blades are on UPS so the fysical host machines (Windows Server 2008) never went down. Our main switches are not on UPS (yet) and we saw the behaviour similar to the following (as distilled from the event logs). The nodes in the cluster lost means of communication (because the external switches went down). The cluster wants to bring down one (the first) of the nodes (to start failover?). The previous step impacts clustered storage where the virtual machine VHD's are located. All VM's got brutally terminated and were found in a failed state in the failover manager in the host OS'es. The Linux VM's were kernel panicking and looked like they had their disk ripped out. This whole setup is rather new to us, so we are still learning about this. The question: We are putting switches on UPS soon but were wondering if the above is expected behavior (seems rather fragile) or if there are obvious improvements configuration-wise to handle such scenario's ? I can upload an evtx file concerning what exactly was going on in case that's necessary.

  Read the article

• What can I do to determine the root cause of a Windows server hanging/freezing?

  - by Aaronaught

  We set up a new server here a few weeks ago that I am informally responsible for managing. Almost everything works perfectly except for one thing: Every so often it hangs without warning. To clarify: When I say hangs, I mean completely. None of the services respond and I'm unable to even get onto a local console - the display acts as though there's no VGA signal. One time, the server actually responded to pings, another time I got the "destination host unreachable" response, but most of the time the pings just time out, as one would expect for a hung server. Event logs don't show anything after a reboot. I don't mean that they don't show anything interesting, I mean that they don't show anything at all from before the failure occurs to after the reboot. And there are never any performance problems, strange errors, or other obvious signs of impending doom before it happens. I don't expect any easy answers here. What I'd like to know his I can methodically determine the root cause of this problem, be it a misbehaving service, defective hardware, or something else. Is there any kind of logging I can set up that will help me get to the bottom of this? Any hardware diagnostics or remote monitoring? Anything else I can do to help me discover what's actually happening, or at least be able to eliminate what isn't wrong? Just to reiterate, I really don't want to start speculating about possible causes and take a trial-and-error approach, because it's going to be at least several days at a time before I would have conclusive results. I'm looking for solutions to reliably trace the problem to its source.

  Read the article

• How can I use an own asp page as 404 error page on a Windows 7 pro IIS 7.5 local installation

  - by Edelcom

  Running Windows 7 Pro Running local IIS 7.5 ( for web development purposes ) Edited hosts file to be able to use http://www.sitestepper.dev Site build in subfolder of the inetpub/wwwroot/staplijst Site can be viewed using http://www.sitestepper.dev/staplijst/whatever-page.htm I have an http://www.sitestepper.dev/p.asp page I would like to call when an unknown page is requested. This technique works fine on the deployed version of this web site ( deployed on an Windows 2003 server running IIS 7 - not sure about the 7 but it is the version deployed with Windows 2003 server ). I tried ( in the Edit Custom Error Dialog ) : Execute a URL on this site: with value /staplijst/p.asp and Respond with a 302 redirect: with value http://www.sitestepper.dev/staplijst/p.asp I tried this in the properties of the 'Default Web Site' , and I tried this at the staplijst level. Even tried it with values without the /staplijst. I restarted the default web site after each change. And even stopped/started the Web service. But nothing seems to work, I keep getting the 'Server Error In Application "DEFAULT WEB SITE"' , HTTP Error 404.0 error. What am I missing here - probably something obvious, but I don't see it ? Thanks in advance

  Read the article

• How to turn off Windows Azure's "This copy of Windows is not genuine" message?

  - by Sid

  Is there any setting/configuration item to avoid Windows Azure from printing that error on the screen or detecting it? I've put a screenshot below that shows the message when you RDP into the web role. My web role runs on Windows Azure Guest OS 1.17 (variant of Windows Server 2008 SP2) Background: I was explaining our architecture to some outside engineers (NDA'd and all) and had to demystify the webrole as they were unfamiliar with Azure. I RDP'd into the VMs running the Web Role when one of their engineers gasped "are you guys running pirated copies of Windows in the cloud?" I also noticed that within the RDP screen, the Azure machines had "This copy of Windows is not genuine" on the bottom left corner. Now obviously, Microsoft is running their own OS in their own datacenter with no influence from me. So no 'piracy' here, despite that obvious warning. However, they seemed so distracted by this ("how can it be? really? hmmm?") that we wasted more time talking about it than the actual matter at work. Like I said, they have little exposure to Azure but have value add elsewhere. I want to get rid of this so I don't have to explain this in the future. PS Microsoft: If you're going to modify Windows Server <XYZ> into Windows Azure <A.B> , you should also modify the code that verifies product integrity.

  Read the article

• Windows Server 2012 licensing issue preventing RDP connections?

  - by QF_Developer

  I am witnessing an unusual behaviour on 1 of 5 Windows Server 2012 R2 machines (clean install) that is preventing any remote connections from being established via RDP. I have run through the prerequisites for RDP here but I am finding that any remote connection attempt instantly stops the "Windows Protection Service". When I check the event logs I see the following entry. The Software Protection Service has stopped Event ID: 903 Source: Security-SPP From what I have read Security-SPP is tasked with enforcing activation and licensing, it appears that RDP requires this service to be in the running state. Is it possible that I have inadvertently activated this instance of Windows with a key that has already been associated to another instance (We have 5 keys as part of an MSDN subscription)? Would this be sufficient to block RDP access? When I look under System Properties (Windows Activation) it states that Windows is activated and there are no other obvious indicators that there's a licensing issue. EDIT 1: I ran a Powershell script to display the product keys for all servers in order to check for any duplication. For the problematic server I am getting the message The RPC server is unavailable.

  Read the article

• Postfix auto create Maildir

  - by Eugene

  I've been beating my head against a wall for a while now on this one. Basically, here is the rundown: Our MX record points to a frontend SMTP server, which contains aliases for actually routing the mail. No alias, no access to the backend storage server, which is what our clients connect to. I'm upgrading the backend email server. Currently, a user is created for every email user on the server, which creates the mailbox. On the new server, everything autheticates through PAM to an LDAP server (all of which is working properly). My goal is to get Postfix to create the Maildir directory for the user automatically. This works fine when I have the /home directory with 777 permissions, but for obvious reasons, this should be avoided. I would like to do this with 775 permissions on /home with a group owner of whatever user Postfix is running as, but I can't seem to figure out what user to use. With the 777 permissions, the /home/$user/Maildir directory is created on message delivery. Does anybody know how I can do this without 777 permissions? The system I am working on is a 64-bit Debian Lenny 5.07 install. Any advice would be appreciated.

  Read the article

• Tell if IIS is being asked to serve compressed pages?

  - by Graham

  Hi, I'm trying to find out if our IIS server is being asked to serve pages compressed. I'm a noob regarding a lot of this so am working my way through the issues. We're using IIS 6.0 and have correctly turned compression on. If I use Fiddler2 to analyse the HTTP requests via localhost, then Fiddler reports that the pages are compressed. If we then access the server over the network, either via its external URL or via the internal server name, Fiddler reports those pages as uncompressed. Therefore, it's logical to assume that something is getting in the way - presumably our ISA server. Our ISA administrator states that ISA is configured to allow compressed requests but what I want to do is to look at the requests coming through to IIS to see if IIS is being asked to serve pages compressed. I'm fairly convinced that our request is going to ISA, ISA is forwarding these, but not with the "compression" details - therefore IIS is not performing any compression. I've looked at the IIS logs but can't see anything obvious about the HTTP request. Is there any way I can check, on the web server itself, this sort of information? One thing that is confusing, but it may be normal, is that the Client IP making the request is not the orignal PC (i.e. mine) and not the ISA firewall, but the web server itself... Thanks

  Read the article

• Xubuntu stuck after login

  - by viraptor

  How can I debug an issue with Xubuntu 12.04 (fresh install) which just waits idle after a login for about 30 seconds? The login screen is delayed correctly. After login, I get my desktop background, but no panels or auto-starting apps. It doesn't seem to be an authentication/pam issue, because I can login without delay at the console while the graphical session is still stuck. There's no disk or cpu activity and no obvious respawning of any process when I look at htop. There's nothing obviously wrong in .xsession-errors. Most interesting errors: openConnection: connect: No such file or directory cannot connect to brltty at :0 WARNING: gnome-keyring:: couldn't connect to: /tmp/keyring-wFn4VR/pkcs11: No such file or directory ... (polkit-gnome-authentication-agent-1:2131): polkit-gnome-1-WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The nam e org.gnome.SessionManager was not provided by any .service files ** Message: applet now removed from the notification area ** Message: using fallback from indicator to GtkStatusIcon ... (xfce4-indicator-plugin:2176): libindicator-WARNING **: IndicatorObject class does not have an accessible description. ... (xfce4-indicator-plugin:2176): Indicator-Application-WARNING **: Unable to get application list: Operation was cancelled Bootchart seems to end before I login, so it's not that helpful. Where else can I look for information?

  Read the article

• Active Directory: Determining DN or OU from log in credentials [closed]

  - by Christopher Broome

  I'm updating a PHP login process to leverage active directory on a Windows server. The logging in process seems pretty straight forward via a "ldap_bind", but I also want to pull some profile information from the AD server (first name, last name, etc...) which seems to require a robust distinguished name (DN). When on the windows server I can grab this via 'dsquery user' on the command prompt, but is there a way to get the same value from just the user's login credentials in PHP? I want to avoid getting a list of hundreds of DNs when on-boarding clients and associating each with one of our users, so any means to programmatically determine this would be preferential. Otherwise, I'll know the domain and host for the request so I can at least set the DC portions of the DN, but the organizational units (OU) seem to be pretty important for querying data. If I can find some of the root level OU values associated with the user I can do a ldap_search and crawl. I browsed through the existing questions and found some similar but nothing that really addressed this, so my apologies if the obvious answer is out there. Thanks for the help.

  Read the article

• How do I tell Windows to use 802.11 in preference to 3G?

  - by Jon Skeet

  I have a Samsung NC-10 netbook which I take to work every day. Most of the time I use it just on the train/bus, but I also use it at work and home. It has a built-in 3G card which I want to use when travelling, but I'd prefer to use wifi when I'm at work or home, for obvious reasons. Unfortunately, if the 3G connection is up, Windows appears to use that in preference to wifi. Starting up and shutting down the 3G modem is a bit of a pain - it's not hard as such, just a bit inconvenient. Ideally I'd like it to always be up, and even have the connection itself up all the time, but without routing traffic through it if there's a wifi connection up. This is what my Android phone does, for example. Is there somewhere in Windows which lets me express an ordering for network interfaces? I suspect the routing table may be relevant, but it's a bit of a pain to mess around with. I'd really expect there to be a simple GUI way of setting this up - after all, it would equally be useful when dealing with wired vs wifi connections. I'm currently using Windows XP Home, but Windows 7 answers would also be useful as I'll be migrating soon.

  Read the article

• Stack Managed Switches over a distance

  - by Joel Coel

  We have several buildings with stacked switches, where the distance between the stacked units is considerable... separate floors, or at opposite ends of a hallway. They are 3Com switches that stack using cat6 cabling. These switches are coming up on 12 years old now, and as I look around at replacements it seems no one supports this scenario any more. Stacking switches want to use fiber links (it more for me to run and terminate the fiber stacking cables than to purchase the switch) or other custom cables that seem only intended to jump up to the next unit in a rack. What have others done to support stacking over a distance? I'm considering breaking up the stacked switches into separate managed entities and just bridging from the root switch in the buildings, but I'd really like to avoid that for what I hope are obvious reason. The closest thing I've found are from netgear that use hdmi cables for the stacking connection... I could try to support that by running an additional cat6 line and re-terminating both links into a single hdmi port, but I have concerns over that approach as well.

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• Remote Desktop leaves host unresponsive

  - by Jeff Dalley

  I have my desktop PC at home set up to accept remote connections, and I often connect to it from work on my laptop via mstsc.exe. However, every time I remote to it, I find when I go home that despite the monitor being on - it's not receiving an image and it looks as though the computer is hibernating/asleep. I basically have to restart it whenever I get home and I know there's an answer for why its doing this. More details: When exiting the remote session, I have tried both logging off the account, and closing the RDP window without logging off; both give the same result. When I get home to the desktop I of course try moving the mouse, ctrl+alt+del to see if its responsive to restart, multiple key-press to see if I can get any audio out of it; It seems pretty obvious its sleeping/hibernating in some way: Nothing happens in any of these cases and a physical restart is necessary. Both desktop and laptop are running Windows 7 Ultimate. I'm thinking it really is sleeping/hibernating it, and I'm not sure why because left alone my desktop's power options are set to never turn off the HDD or change its state - I leave it on 24/7. This could be a stupid error on my part but I just can't see it! Thanks.

  Read the article

• How can I read PDFs with e-reader on a Lenovo tablet?

  - by Jack M

  This is my first time using a tablet and I'm totally lost - this must be what computers look like to old people. This is a Lenovo Thinkpad tablet. I don't see a specific model number on it (it was passed down to me second hand). What I'd like to do is read a PDF. I'm fairly certain I successfully transferred the PDF onto the tablet via an SD card, and I noticed this thing has an app called "eReader" on it, so I started that up. All I see are empty bookshelves, and no obvious buttons or settings anywhere. I saw in multiple places that you have to, as one site puts it: ...copy and paste the relevant files into the eBooks folder and they will appear on the eReader shelf for your consumption... But I have no idea how to: Access the file system. Locate the eBooks folder. Copy and paste files. Will I need a file explorer app? If so, how can I install that given that my only method of getting data onto this tablet is an SD card (no wireless internet).

  Read the article

< Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >