Search Results

Search found 9661 results on 387 pages for 'ki lya online fr'.

Page 366/387 | < Previous Page | 362 363 364 365 366 367 368 369 370 371 372 373  | Next Page >

• DHCP and DNS services configuration for VOIP system, windows domain, etc

  - by Stemen

  My company has numerous physical offices (for purposes of this discussion, 15 buildings). Some of them are well-connected to our primary data center via fiber. Others will be connected to the data center by P2P T1. We are in the beginning stages of implementing an Avaya VOIP telephone system, and we will be replacing a significant portion of our network infrastructure in the process. In tandem with the phone system implementation, we are going to be re-addressing some of our networks, and consolidating most of our Windows domains into one (not all domains, just most). We currently have quite a few Windows domains, and they of course each have their own DNS zones. A few of those networks currently use DHCP, but the majority use static IP assignments for every device. I'm tired of managing static assignments -- I want to use DHCP configuration on everything except servers. Printers and etc will have DHCP reservations. The new IP phones will need to get IP addresses from DHCP, though they need to be in a separate VLAN from the computers/printers/etc. The computers and printers need to be registered in DNS. That's currently handled by the Windows DHCP servers on each of the respective domains. We need to place a priority on DHCP and DNS being available on a per-site basis (in case something were to interrupt the WAN connection) for computers and (primarily) phones. Smaller locations (which will have IP phones but not be a member of any Windows domain) will not have any Windows DNS/DHCP server(s) available. We also are looking for the easiest way to replace a part if it were to fail. That is to say, if a server/appliance/router hosting DHCP were to crash hard, and we couldn't extremely quickly recover the DHCP reservations and leases (and subsequently restore them onto a cold spare), we anticipate that bad things could happen. What is the best idea for how to re-implement DNS and DHCP keeping all of the above in mind? Some thoughts that have been raised (by myself or my coworkers): Use Windows DNS and DHCP servers, where they exist, and use IP helpers to route DHCP requests to some other Windows server if necessary. May not be acceptable if the WAN goes down and clients don't get a DHCP response. Use Windows DNS (everywhere, over WAN in some cases) and a mix of Windows DHCP and DHCP provided by Cisco routers. Every site would be covered for DHCP, but from what I've read, Cisco routers can't handle dynamic registration of DHCP clients to Windows DNS servers, which might create a problem where Cisco routers are used for DHCP. Use Windows DNS (everywhere, over WAN in some cases) and a mix of Windows DHCP and DHCP provided by some service running on an extremely low-price linux server. Is there any such software that would allow DHCP leases granted by these linux boxes to be dynamically registered on the Windows DNS servers? Come up with a Linux solution for both DNS and DHCP, and deploy low-price linux servers to every site. Requirements would be that the DNS zone be multi-master (like Windows DNS integrated with Active Directory), that DHCP be able to make dynamic DNS registrations in that zone, for every lease (where a hostname is provided and is thus possible), and that multiple servers be either authoritative for the same DHCP scope or at least receiving a real-time copy / replication / sync of the leases table so that if one server dies, we still know which MAC has what address. Purchase dedicated DNS/DHCP appliances, deploying to all sites. From what I read/see, this solves all of our technical problems. Then come the financial problems... I don't have a ton of money to spend on this. Or, some other solution that we've thus far overlooked and will consider upon recommendation. Can Cisco routers or Windows servers sync DHCP lease tables so that multiple servers can be authoritative (or active/passive for all I care) for the same scope, in case one of the partners were to fail? I've read online (repeatedly) that ISC's DHCP is able to maintain the same lease table across multiple servers, in order to solve this problem. Does anyone have any experience or advice to regarding that?

  Read the article

• SQL Server Issue: Could not allocate space for object ... primary filegroup is full

  - by Luke

  Trying to figure out a problem at an office that has SQL Server 2005 installed on Windows SBS Server 2008. Here's the setup: It's an office, and the person who set this all up is nowhere to be found. I'm the best hope they have... One of the programs they use on a workstation gives them an error of "Could not allocate space for object 'Billing' in database "MyDatabase" because primary filegroup is full" when trying to save an entry in their software. I searched around for hours, looking for possible solutions. One was to check for available disk space, and another was to defrag. I checked the hard drives on the server, and there is plenty of space free. I also defragged, which may have helped the problem somewhat. It's hard to say, because it seems like with the nature of the error, if you try over and over you might get it to actually save. My next step was to try to see if autogrowth was enabled on the database. This would seem to be a likely / possible solution, but I can't access the database! If I run the SQL Management Studio, I can log in as my Windows user and view the list of databases. However, if I try to do anything (actually view the database, view the properties, add or edit users), I get errors that I don't have permission. For what it's worth, I also tried runing Management Studio as Administrator, in case that would help. No difference, though. Now, what I'm guessing is going on -- from my limited knowledge of SQL and from reading online -- is that though I'm logged in as a Windows administrator, that account does NOT have SQL access. I do see a list of SQL users, including SA, but I again don't have permission to add one or to change the password on an existing one. And nobody at the office has any idea what the SQL passwords could be. So... here's my thinking thus far: 1 - The "Could not allocate" error likely points to a database that needs to be allowed to autogrow. Especially since I verified there is plenty of free space and the HD has been defragmented. 2 - Enabling autogrow would be very easy to do if I had the proper access within SQL Management Stuido. That leads me to this link: http://blogs.technet.com/b/sqlman/archive/2011/06/14/tips-amp-tricks-you-have-lost-access-to-sql-server-now-what.aspx It sounds like it's a step-by-step guide for giving me the access I need to SQL. I'm guessing that if I followed this guide, I would be able to then log in to the SQL server via Management Studio with the proper permissions, and would be able to enable autogrow (or simply view the status of the existing database), and hopefully solve the "Could not allocate space" problem! So I guess I have a few questions: 1 - Would you guys agree with my "diagnosis"? Think I'm barking up the right tree? 2 - Is there any risk at all in hurting / disabling / wrecking the current SQL database or setup with me going through the guide to regain SQL access? I understand that per the guide, I would have to temporarily shut down SQL, so obviously it wouldn't be accessible during that time. But it wouldn't be worth the risk if there's a chance I could mess anything up... Like I said, the workstations ARE currently accessing the database somehow, but nobody knows with what login info or anything. Basically, it's set up, it works (usually), but if they had to reload the software, nobody would know how. Any feedback would be appreciated!! The problem is such that it's not an emergency for them, but an annoyance. If I could fix it, it would be wonderful. But if not, I think they'll manage, especially as they are going to eventually stop using this software. Thank you so much for your time! Luke

  Read the article

• Windows 2008 Unknown Disks

  - by Ailbe

  I have a BL460c G7 blade server with OS Windows 2008 R2 SP1. This is a brand new C7000 enclosure, with FlexFabric interconnects. I got my FC switches setup and zoned properly to our Clariion CX4, and can see all the hosts that are assigned FCoE HBAs on both paths in both Navisphere and in HP Virtual Connect Manager. So I went ahead and created a storage group for a test server, assigned the appropriate host, assigned the LUN to the server. So far so good, log onto server and I can see 4 unknown disks.... No problem, I install MS MPIO, no luck, can't initialize the disks, and the multiple disks don't go away. Still no problem, I install PowerPath version 5.5 reboot. Now I see 3 disks. One is initialized and ready to go, but I still have 2 disks that I can't initialize, can't offline, can't delete. If I right click in storage manager and go to properties I can see that the MS MPIO tab, but I can't make a path active. I want to get rid of these phantom disks, but so far nothing is working and google searches are showing up some odd results, so obviously I'm not framing my question right. I thought I'd ask here real quick. Does anyone know a quick way to get rid of these unknown disks. Another question, do I need the MPIO feature installed if I have PowerPath installed? This is my first time installing Windows 2008 R2 in this fashion and I'm not sure if that feature is needed or not right now. So some more information to add to this. It seems I'm dealing with more of a Windows issue than anything else. I removed the LUN from the server, uninstalled PowerPath completely, removed the MPIO feature from the server, and rebooted twice. Now I am back to the original 4 Unknown Disks (plus the local Disk 0 containing the OS partition of course, which is working fine) I went to diskpart, I could see all 4 Unknown disks, I selected each disk, ran clean (just in case i'd somehow brought them online previously as GPT and didn't realize it) After a few minutes I was no longer able to see the disks when I ran list disk. However, the disks are still in Disk Management. When I try and offline the disks from Disk Management I get an error: Virtual Disk Manager - The system cannot find the file specified. Accompanied by an error in System Event Logs: Log Name: System Source: Virtual Disk Service Date: 6/25/2012 4:02:01 PM Event ID: 1 Task Category: None Level: Error Keywords: Classic User: N/A Computer: hostname.local Description: Unexpected failure. Error code: 2@02000018 Event Xml: 1 2 0 0x80000000000000 4239 System hostname.local 2@02000018 I feel sure there is a place I can go in the Registry to get rid of these, I just can't recall where and I am loathe to experiement. So to recap, there are currently no LUNS attached at all, I still have the phantom disks, and I'm getting The system cannot find the file specified from Virtual Disk Manager when I try to take them offline. Thanks!

  Read the article

• Users loggin to 3Com switches authenticated by radius not getting admin priv and no access available

  - by 3D1L

  Hi, Following the setup that I have for my Cisco devices, I got some basic level of functionality authenticating users that loggin to 3Com switches authenticated against a RADIUS server. Problem is that I can not get the user to obtain admin privileges. I'm using Microsoft's IAS service. According to 3Com documentation when configuring the access policy on IAS the value of 010600000003 have to be used to specify admin access level. That value have to be input in the Dial-in profile section: 010600000003 - indicates admin privileges 010600000002 - manager 010600000001 - monitor 010600000000 - visitor Here is the configuration on the switch: radius scheme system server-type standard primary authentication XXX.XXX.XXX.XXX accounting optional key authentication XXXXXX key accounting XXXXXX domain system scheme radius-scheme system local-user admin service-type ssh telnet terminal level 3 local-user manager service-type ssh telnet terminal level 2 local-user monitor service-type ssh telnet terminal level 1 The configuration is working with the IAS server because I can check user login events with the Eventviewer tool. Here is the output of the DISPLAY RADIUS command at the switch: [4500]disp radius SchemeName =system Index=0 Type=standard Primary Auth IP =XXX.XXX.XXX.XXX Port=1645 State=active Primary Acct IP =127.0.0.1 Port=1646 State=active Second Auth IP =0.0.0.0 Port=1812 State=block Second Acct IP =0.0.0.0 Port=1813 State=block Auth Server Encryption Key= XXXXXX Acct Server Encryption Key= XXXXXX Accounting method = optional TimeOutValue(in second)=3 RetryTimes=3 RealtimeACCT(in minute)=12 Permitted send realtime PKT failed counts =5 Retry sending times of noresponse acct-stop-PKT =500 Quiet-interval(min) =5 Username format =without-domain Data flow unit =Byte Packet unit =1 Total 1 RADIUS scheme(s). 1 listed Here is the output of the DISPLAY DOMAIN and DISPLAY CONNECTION commands after users log into the switch: [4500]display domain 0 Domain = system State = Active RADIUS Scheme = system Access-limit = Disable Domain User Template: Idle-cut = Disable Self-service = Disable Messenger Time = Disable Default Domain Name: system Total 1 domain(s).1 listed. [4500]display connection Index=0 ,Username=admin@system IP=0.0.0.0 Index=2 ,Username=user@system IP=xxx.xxx.xxx.xxx On Unit 1:Total 2 connections matched, 2 listed. Total 2 connections matched, 2 listed. [4500] Here is the DISP RADIUS STATISTICS: [4500] %Apr 2 00:23:39:957 2000 4500 SHELL/5/LOGIN:- 1 - ecajigas(xxx.xxx.xxx.xxx) in un it1 logindisp radius stat state statistic(total=1048): DEAD=1046 AuthProc=0 AuthSucc=0 AcctStart=0 RLTSend=0 RLTWait=2 AcctStop=0 OnLine=2 Stop=0 StateErr=0 Received and Sent packets statistic: Unit 1........................................ Sent PKT total :4 Received PKT total:1 Resend Times Resend total 1 1 2 1 Total 2 RADIUS received packets statistic: Code= 2,Num=1 ,Err=0 Code= 3,Num=0 ,Err=0 Code= 5,Num=0 ,Err=0 Code=11,Num=0 ,Err=0 Running statistic: RADIUS received messages statistic: Normal auth request , Num=1 , Err=0 , Succ=1 EAP auth request , Num=0 , Err=0 , Succ=0 Account request , Num=1 , Err=0 , Succ=1 Account off request , Num=0 , Err=0 , Succ=0 PKT auth timeout , Num=0 , Err=0 , Succ=0 PKT acct_timeout , Num=3 , Err=1 , Succ=2 Realtime Account timer , Num=0 , Err=0 , Succ=0 PKT response , Num=1 , Err=0 , Succ=1 EAP reauth_request , Num=0 , Err=0 , Succ=0 PORTAL access , Num=0 , Err=0 , Succ=0 Update ack , Num=0 , Err=0 , Succ=0 PORTAL access ack , Num=0 , Err=0 , Succ=0 Session ctrl pkt , Num=0 , Err=0 , Succ=0 RADIUS sent messages statistic: Auth accept , Num=0 Auth reject , Num=0 EAP auth replying , Num=0 Account success , Num=0 Account failure , Num=0 Cut req , Num=0 RecError_MSG_sum:0 SndMSG_Fail_sum :0 Timer_Err :0 Alloc_Mem_Err :0 State Mismatch :0 Other_Error :0 No-response-acct-stop packet =0 Discarded No-response-acct-stop packet for buffer overflow =0 The other problem is that when the RADIUS server is not available I can not log in to the switch. The switch have 3 local accounts but none of them works. How can I specify the switch to use the local accounts in case that the RADIUS service is not available?

  Read the article

• Unmountable boot volume blue screen, what should I do?

  - by Josh

  I was trying to install an update from NVIDIA for my GTX 560, but while it was installing, my computer shut off. After a few minutes, I turned it back on. It got to the Windows boot screen and then had a blue screen error and if left on it would just keep doing that. A few details about my PC: I haven't added any new hardware or software, I'm running Windows XP Professional 32 bit and Windows XP Professional 64 bit on the same hard drive for about 2 years now. I have 2 other hard drives also, but I don't have one large enough to hold everything from my main hard drive, so formatting isn't an option. Now, as for what I've done so far: I've scanned the RAM with "memtest - 86 v3.4" and it said that it was good. I scanned the hard drive in question with chkdsk /r and it gets to 50% and tells me something along the lines of "the drive has one or more unrepairable problems". I also tried to use chkdsk on the drive I installed the new copy of Windows XP on and it got to 75% then jumped back down to 50% and stayed there (I had to reboot the pc). So, after that, I turned off auto reboot and got to read the blue screen error code and I looked it up only to find that nobody seems to have this problem, just problems close to it. The error code is 0x000000ed and I've seen a lot of these online but none that matched the detailed part of the code UNMOUNTABLE_BOOT_VOLUME 0x000000ed (0xfffffadf513c19a0, 0xffffffffc0000006, 0, 0) So, I have installed another copy of Windows XP Professional 32 bit on one of my other hard drives in hopes of accessing the data on the drive in question and when it booted it asked if I wanted chkdsk to scan the drive in question and this is what it found: file record segments 12740, 12741, 12742 and 12743 were reported unreadable. Then it says "recovering lost files" but it sits there for a few seconds and then just boots to Windows. I can't access the drive in question from Windows as far as I can tell, it just says "drive not accessible" and when I go to properties it says that the drive has 100% free space. So, after that failed I didn't give up, I looked for another way to access the drive in question. I used a Ubuntu bootable disk and was able to access the drive in question without any problems. However, I can't access the registry editor because it's a .exe file and that won't load from Ubuntu. I made a copy of the "Windows" folder and put it on one of my other drives and that's where I'm stuck at now. I'm sure my drive works fine, I know chkdsk can't fix the problem with it and I know what caused the problem in the first place for the most part, but I don't know what to do about it. I have a laptop that I can use to download and burn disks if needed and I also have the other copy of Windows XP Professional 32 bit that I can use that's installed on the computer in question (so I know it's not a hardware issue). I'm pretty sure it's a driver issue or the update was editing the registry when it shut off and left me when a broken registry. I've tried accessing C:\Windows\System32\CONFIG only to find that the Windows XP disk repair option can't even access the files on the drive in question. It seems I'll need to be able to do everything from Ubuntu unless there is something I haven't tried with the Windows XP disk. I didn't install the update on Windows XP 64 bit but yet it also has the same blue screen error (that's where the error code above came from but I haven't checked to see if they are the same). They both stopped working at the same time, so I assume it's one problem causing both to not work.

  Read the article

• Upgraded Ubuntu, all drives in one zpool marked unavailable

  - by Matt Sieker

  I just upgraded Ubuntu 14.04, and I had two ZFS pools on the server. There was some minor issue with me fighting with the ZFS driver and the kernel version, but that's worked out now. One pool came online, and mounted fine. The other didn't. The main difference between the tool is one was just a pool of disks (video/music storage), and the other was a raidz set (documents, etc) I've already attempted exporting and re-importing the pool, to no avail, attempting to import gets me this: root@kyou:/home/matt# zpool import -fFX -d /dev/disk/by-id/ pool: storage id: 15855792916570596778 state: UNAVAIL status: One or more devices contains corrupted data. action: The pool cannot be imported due to damaged devices or data. see: http://zfsonlinux.org/msg/ZFS-8000-5E config: storage UNAVAIL insufficient replicas raidz1-0 UNAVAIL insufficient replicas ata-SAMSUNG_HD103SJ_S246J90B134910 UNAVAIL ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523 UNAVAIL ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969 UNAVAIL The symlinks for those in /dev/disk/by-id also exist: root@kyou:/home/matt# ls -l /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910* /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51* lrwxrwxrwx 1 root root 9 May 27 19:31 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910 -> ../../sdb lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part9 -> ../../sdb9 lrwxrwxrwx 1 root root 9 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523 -> ../../sdd lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part1 -> ../../sdd1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part9 -> ../../sdd9 lrwxrwxrwx 1 root root 9 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969 -> ../../sde lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part1 -> ../../sde1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part9 -> ../../sde9 Inspecting the various /dev/sd* devices listed, they appear to be the correct ones (The 3 1TB drives that were in a raidz array). I've run zdb -l on each drive, dumping it to a file, and running a diff. The only difference on the 3 are the guid fields (Which I assume is expected). All 3 labels on each one are basically identical, and are as follows: version: 5000 name: 'storage' state: 0 txg: 4 pool_guid: 15855792916570596778 hostname: 'kyou' top_guid: 1683909657511667860 guid: 8815283814047599968 vdev_children: 1 vdev_tree: type: 'raidz' id: 0 guid: 1683909657511667860 nparity: 1 metaslab_array: 33 metaslab_shift: 34 ashift: 9 asize: 3000569954304 is_log: 0 create_txg: 4 children[0]: type: 'disk' id: 0 guid: 8815283814047599968 path: '/dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part1' whole_disk: 1 create_txg: 4 children[1]: type: 'disk' id: 1 guid: 18036424618735999728 path: '/dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part1' whole_disk: 1 create_txg: 4 children[2]: type: 'disk' id: 2 guid: 10307555127976192266 path: '/dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part1' whole_disk: 1 create_txg: 4 features_for_read: Stupidly, I do not have a recent backup of this pool. However, the pool was fine before reboot, and Linux sees the disks fine (I have smartctl running now to double check) So, in summary: I upgraded Ubuntu, and lost access to one of my two zpools. The difference between the pools is the one that came up was JBOD, the other was zraid. All drives in the unmountable zpool are marked UNAVAIL, with no notes for corrupted data The pools were both created with disks referenced from /dev/disk/by-id/. Symlinks from /dev/disk/by-id to the various /dev/sd devices seems to be correct zdb can read the labels from the drives. Pool has already been attempted to be exported/imported, and isn't able to import again. Is there some sort of black magic I can invoke via zpool/zfs to bring these disks back into a reasonable array? Can I run zpool create zraid ... without losing my data? Is my data gone anyhow?

  Read the article

• Cisco VPNClient from Mac won't connect using iPhone Tethering

  - by Dan Short

  I just set up iPhone tethering from my Snow Leopard Macbook Pro to my iPhone 3GS with the Datapro 4GB plan from AT&T. When attempting to connect to my corporate VPN from the MacBook Pro with Cisco VPNClient 4.9.01 (0100) I get the following log information: Cisco Systems VPN Client Version 4.9.01 (0100) Copyright (C) 1998-2006 Cisco Systems, Inc. All Rights Reserved. Client Type(s): Mac OS X Running on: Darwin 10.6.0 Darwin Kernel Version 10.6.0: Wed Nov 10 18:13:17 PST 2010; root:xnu-1504.9.26~3/RELEASE_I386 i386 Config file directory: /etc/opt/cisco-vpnclient 1 13:02:50.791 02/22/2011 Sev=Info/4 CM/0x43100002 Begin connection process 2 13:02:50.791 02/22/2011 Sev=Warning/2 CVPND/0x83400011 Error -28 sending packet. Dst Addr: 0x0AD337FF, Src Addr: 0x0AD33702 (DRVIFACE:1158). 3 13:02:50.791 02/22/2011 Sev=Warning/2 CVPND/0x83400011 Error -28 sending packet. Dst Addr: 0x0A2581FF, Src Addr: 0x0A258102 (DRVIFACE:1158). 4 13:02:50.792 02/22/2011 Sev=Info/4 CM/0x43100004 Establish secure connection using Ethernet 5 13:02:50.792 02/22/2011 Sev=Info/4 CM/0x43100024 Attempt connection with server "209.235.253.115" 6 13:02:50.792 02/22/2011 Sev=Info/4 CVPND/0x43400019 Privilege Separation: binding to port: (500). 7 13:02:50.793 02/22/2011 Sev=Info/4 CVPND/0x43400019 Privilege Separation: binding to port: (4500). 8 13:02:50.793 02/22/2011 Sev=Info/6 IKE/0x4300003B Attempting to establish a connection with 209.235.253.115. 9 13:02:51.293 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 10 13:02:51.894 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 11 13:02:52.495 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 12 13:02:53.096 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 13 13:02:53.698 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 14 13:02:54.299 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 15 13:02:54.299 02/22/2011 Sev=Info/4 IKE/0x43000075 Unable to acquire local IP address after 5 attempts (over 5 seconds), probably due to network socket failure. 16 13:02:54.299 02/22/2011 Sev=Warning/2 IKE/0xC300009A Failed to set up connection data 17 13:02:54.299 02/22/2011 Sev=Info/4 CM/0x4310001C Unable to contact server "209.235.253.115" 18 13:02:54.299 02/22/2011 Sev=Info/5 CM/0x43100025 Initializing CVPNDrv 19 13:02:54.300 02/22/2011 Sev=Info/4 CVPND/0x4340001F Privilege Separation: restoring MTU on primary interface. 20 13:02:54.300 02/22/2011 Sev=Info/4 IKE/0x43000001 IKE received signal to terminate VPN connection 21 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700008 IPSec driver successfully started 22 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 23 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x4370000D Key(s) deleted by Interface (192.168.0.171) 24 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 25 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 26 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 27 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x4370000A IPSec driver successfully stopped The key line is 15: 15 13:02:54.299 02/22/2011 Sev=Info/4 IKE/0x43000075 Unable to acquire local IP address after 5 attempts (over 5 seconds), probably due to network socket failure. I can't find anything online about this. I found a single entry for the error message in Google, and it was a swedish (or some other nordic language site) that didn't have an answer to the question. I've tried connecting through both USB and Bluetooth tethering to the iPhone, and they both return the exact same results. I don't have direct control over the firewall, but if changes are necessary to make it work, I may be able to get the powers-that-be to make adjustments. A solution that doesn't require reconfiguring the firewall would be far better of course... Does anyone know what I can do to make this behave? Thanks, Dan

  Read the article

• Strange enduser experience with Liferay, Glassfish and Apache on RedHat

  - by Pete Helgren

  Tried multiple forums to get to the bottom of this. I hope I can get some direction here: Here is the stack I am working with: Red Hat Enterprise Linux Server release 5.6 (Tikanga) Liferay 6.0.6 on Glassfish 3.0.1 MySQL 5.0.77 Apache 2.2.3 The Liferay portal provides a variety of portlets to end users. Static content (web pages), static resources (primarily pdf and mp3 files 1mb - 80mb in size), File upload and download capabilities (primarily 40-60mb mp3 files) and online streaming of those MP3 files. Here is the strange end user experiences: Under normal load: (20-30) users uploading, downloading or streaming files and 20-30 accessing static content (some of it downloads), we see the following: 1) Clicking a link triggers the download of a portion of an MP3 (the portion is a few seconds long). 2) Clicking on a link tiggers the download of the page content rather than rendering. 3) Clicking a link causes the page to dump binary data to the end user rather than the expected content. 4) Clicking a link returns the text of a javascript file rather than rendering the page. Each occurrence is totally random (or appears so). Sometimes it works, sometimes it doesn't. It seems to have no relation to browser or client OS. The strange events seem to occur much more frequently when using an SSL connection rather than regular http. Apache serves as a proxy server only (reverse). It basically passes all the requests through to Glassfish. There isn't any static content proxy served by Apache. We rebuilt the entire stack from scratch and redeployed the portlet wars and still have the same issues. Liferay is running as a single server (not clustered). We disabled mod_cache in Apache. The problems are more frequent as the server load grows. This morning the load is pretty light and we are seeing few problems but the use of the site will grow, particularly tonight around 9pm CST through Wednesday morning. You could try the site (http://preview.bsfinternational.org) during those times and I would expect that you might experience one of the weirdnesses as you randomly click links on the site (https is invoked only when signed in). Again, https seems to exacerbate the issue. This seems very much like a caching issue but I don't know where in the stack to start peeling the onion. Apache? Liferay? Glassfish? MySQL? Maybe even Redhat? We are stumped and most forums we have posted to (LifeRay and Glassfish) have returned very few suggestions. I just need an idea of where to start looking. I understand that we could have a portlet EDIT: Opening the files in a Hex editor that appear to be pages that download rather than render, we see that the first 4000 characters are "junk" and then the "HTTP/1.1 ...." 'normal' header is seen. So something is dumping a jumble of characters up to offset 4000 (when viewing it in a Hex editor). Perhaps a clue? Ideas?

  Read the article

• TV not detected by Windows/VGA - when there is a WHDI device in the signal chain

  - by ashwalk

  I'm at my wit's end with this one... I had an EVGA GTS 250, and I used to plug it's HDMI out into a WHDI sender, which transmitted to its corresponding WHDI receiver 15ft away, which then connected to a Samsung LN40D LCD TV through another HDMI cable. PC/VGA < [hdmi cable] < WHDI sender <[air] WHDI receiver < [hdmi cable] < TV It was perfect, stable, no perceivable latency. I just plugged everything the first time and it worked instantly. It sent 5.1 audio, and Windows/nVidia Control Center detected the TV by its name. The WHDI device is this one: http://goo.gl/Q8iWI5 Now I bought an EVGA GTX 650, and WHDI doesn't work anymore. Both Windows and nVidia Control Center won't detect the TV, only the monitor that's connected via DVI. The TV screen shows "TX202913 connected. Check video signal." on top of a black screen. Though the device is not the problem itself, just the fact that it's not allowing direct connection between PC and TV. I would bet that if put an AVR in its place I'd also have this issue. The HDMI on this new card works with other monitors. If I put the older card back, WHDI works normally. I have googled this for 5 months on and off. Once I bumped into a page that showed how to force a display device to always-on through registry edit. Once I restarted windows, the Tv (through WHDI) displayed my expanded or duplicated desktop at 1024x768 ONLY, and listed the display as "digital display". I could not change the resolution and it wouldn't playback audio (although the option was available at nVidia Control Center HDMI audio options, but did not work). This proves that there is no conflict between the devices, except that software-wise, Windows cannot, for the life of it, understand that there's a TV there to send video/audio to. Since this won't do (no audio, poor video), I reverted this regedit. It's also not an EDID problem within the TV, since when connected directly it works. The last weird bit of this saga is that today, I reminded of Windows' "Add Device" dialog, gave it a go, and a "Samsung Generic UPNP TV" showed up, which I promptly installed the drives for, rising to a climax of... ...NOTHING HAPPENING. As far as I can tell, it really didn't change anything other than using up a few kb in my main disc. I should also say that I looked a LOT into handshake problems and nothing applied either. Do any of you have an idea of what may be going on? I can't stand the thought of having a us$200 device not working because of the addition of a newer graphics card, when the much older one had no issues. There is absolutely NO REASON for this to happen. There is NO documentation on WHDI online. Apparently no one buys this stuff. For the same reason, no one responded to this same plea for help on NVidia and EVGA forums. Worst case, this can be a warning about this setup for people in the future. Thanx in advance.

  Read the article

• Home ADSL Modem Dropping Packets?

  - by Cody

  I know this is supposed to be a "pro" forum, but I'm hoping someone can help since my ISP isn't doing much to try and fix things. My ISP has given me a DSL modem / Router combo - a ADB / Pirelli P.DG A2100N and I have a 4096 / 767 kbps connection. I use it purely as modem and router, and have the wireless AP feature turned off. I run it to a Ubiquiti Networks Toughswitch and use a Ubiquiti UAP as the wireless access point - although I've ran tests directly wired to the router with nothing else connected, and still see the same issues. I've been having issues where latency suddenly spikes from 8ms to google.com to 250+ if someone does anything on the internet. If I run a speedtest or something, I can see latencies above 3000ms. Regularly when downloading something, even if the speed is throttled to , it can get random drops to 0kbps every few seconds. Online gaming is impossible because I notice the sudden lag-outs in the connection, and video streams or VoIP drop out as well - it's not at all consistent. I managed to find the password to my modem and I don't think I see anything wrong with the settings - but I looked for the logs and found this: Jun 6 17:10:30 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:10:30 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:10:31 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:10:40 user warn kernel: __ratelimit: 63 callbacks suppressed Jun 6 17:10:40 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:10:40 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:10:40 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:10:40 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:10:40 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:10:40 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:22 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:23 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:24 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:24 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:24 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:24 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:24 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:25 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:25 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:25 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:29 user warn kernel: __ratelimit: 15 callbacks suppressed Jun 6 17:11:29 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:29 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:30 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:11:30 user warn kernel: nf_conntrack: table full, dropping packet. Jun 6 17:55:26 user warn kernel: bcmxtmcfg: OAM loopback response not received on VCC 1.1.3 Jun 6 17:55:27 user warn kernel: bcmxtmcfg: OAM loopback response not received on VCC 1.1.4 So, as I understand it, it appears the router is dropping packets? If that's the case, is there anything in the config that I can change? Or should I buy a new router, a new modem, or both?

  Read the article

• Issues configuring Exchange 2010 as well as SSL problems.

  - by Eric Smith

  Possibly-Relevant Background Info: I've recently moved up from icky shared hosting to a glorious, Remote Desktop-administrated VPS server running Windows Server 2008 R2. Even though I'm only 21 now and a computer science major, I've tried to play with every Windows Server release since '03, just to learn new things. What usually happens is inevitably I'll do something wrong and pretty much ruin the install. You're dealing with an amateur here :) Through the past few months of working with my new server, I've mastered DNS, IIS, got Team Foundation Server running (yay!), and can install all of the other basics like SQL Server and Active Directory. The Problem: Now, these last few weeks I've been trying to install Exchange Server 2010 (SP1). To make a long story short, it took me several attempts, and I even had to get my server wiped just so I could start fresh since Exchange decided uninstalling properly was for sissies (cost me $20, bah). Today, at long last, I got Exchange mostly working. There were two main problems left, however, that left me unsatisfied: Exchange installed itself and all of its child sites into Default Web Site. I wanted to access Exchange via mail.domain.com, but instead everything was configured to domain.com. My limited server admin knowledge was not enough to configure IIS or Exchange to move itself over to the website I had set up for it, appropriately titled 'mail.domain.com', which I had bound to a dedicated IP address (I was told this was necessary, but he may have been wrong). I have two SSL certificates: one for my main domain and one for my mail subdomain. For whatever reason, I had issues geting Exchange to use my mail certificate, even though I had assigned the proper roles in the MMC. I did, at one point, get it to work (or mostly work, anyways. Frankly, my memory of today is clouded by intense frustration). Additionally, I was confused which type of SSL certificate I should be using for Exchange. My SSL provider, GoDaddy, allows me to request a new certificate whenever, so I can use either the certificate request provided by IIS or the more complicated and specific request you can create with Exchange. Which type should I be using, the IIS or Exchange certificate? If I must use the Exchange certificate, will that 1) cause issues when I bind that certificate to my mail.domain.com subdomain or 2) is that an unnecessary step? The SSL Certificate Strikes Back When I thought I had the proper SSL certificate assigned for those brief, sweet moments, Google Chrome reported the correct mail.domain.com certificate when browsing https://mail.domain.com. However, Outlook 2010 threw up an error when trying to configure my email account claiming that the certificate didn't match the domain of "mail.domain.com". Is this an issue that will be resolved by problem #2 or is it a separate one entirely? Apologies for the massive wall of text, but I wanted to provide as much info as I possibly could. Exchange is the last thing I'd like installed on my server, and naturally it's turning out to be the hardest. Thanks for any info at all. Even a point in a vague direction would be a huge help at this point. Thanks! -Eric P.S.: The reason I keep ruining my install is that when I attempt to uninstall Exchange, something invariably goes wrong. The last time the uninstaller complained that there was still a mailbox active and it couldn't proceed until I deleted it. ... The only mailbox left was the Administrator account, the built-in one I couldn't delete. So I attempted to manually uninstall it following several guides online only to now be stuck unable to launch the installer and have to get my system wiped AGAIN for the second time today ($40 down the drain, bah!). I do not understand at all why "uninstall" just can't mean "hey, you, delete everything and go away". There's not even a force uninstall option, only a "recover system" option that just fails to fix anything and makes it so I can't even use the GUI uninstaller. </rant>

  Read the article

• "Possible SYN flooding" in log despite low number of SYN_RECV connections

  - by al4

  Recently we had an apache server which was responding very slowly due to SYN flooding. The workaround for this was to enable tcp_syncookies (net.ipv4.tcp_syncookies=1 in /etc/sysctl.conf). I posted a question about this here if you want more background. After enabling syncookies we started seeing the following message in /var/log/messages approximately every 60 seconds: [84440.731929] possible SYN flooding on port 80. Sending cookies. Vinko Vrsalovic informed me that this means the syn backlog is getting full, so I raised tcp_max_syn_backlog to 4096. At some point I also lowered tcp_synack_retries to 3 (down from the default of 5) by issuing sysctl -w net.ipv4.tcp_synack_retries=3. After doing this, the frequency seemed to drop, with the interval of the messages varying between roughly 60 and 180 seconds. Next I issued sysctl -w net.ipv4.tcp_max_syn_backlog=65536, but am still getting the message in the log. Throughout all this I've been watching the number of connections in SYN_RECV state (by running watch --interval=5 'netstat -tuna |grep "SYN_RECV"|wc -l'), and it never goes higher than about 240, much much lower than the size of the backlog. Yet I have a Red Hat server which hovers around 512 (limit on this server is the default of 1024). Are there any other tcp settings which would limit the size of the backlog or am I barking up the wrong tree? Should the number of SYN_RECV connections in netstat -tuna correlate to the size of the backlog? Update As best I can tell I'm dealing with legitimate connections here, netstat -tuna|wc -l hovers around 5000. I've been researching this today and found this post from a last.fm employee, which has been rather useful. I've also discovered that the tcp_max_syn_backlog has no effect when syncookies are enabled (as per this link) So as a next step I set the following in sysctl.conf: net.ipv4.tcp_syn_retries = 3 # default=5 net.ipv4.tcp_synack_retries = 3 # default=5 net.ipv4.tcp_max_syn_backlog = 65536 # default=1024 net.core.wmem_max = 8388608 # default=124928 net.core.rmem_max = 8388608 # default=131071 net.core.somaxconn = 512 # default = 128 net.core.optmem_max = 81920 # default = 20480 I then setup my response time test, ran sysctl -p and disabled syncookies by sysctl -w net.ipv4.tcp_syncookies=0. After doing this the number of connections in the SYN_RECV state still remained around 220-250, but connections were starting to delay again. Once I noticed these delays I re-enabled syncookies and the delays stopped. I believe what I was seeing was still an improvement from the initial state, however some requests were still delayed which is much worse than having syncookies enabled. So it looks like I'm stuck with them enabled until we can get some more servers online to cope with the load. Even then, I'm not sure I see a valid reason to disable them again as they're only sent (apparently) when the server's buffers get full. But the syn backlog doesn't appear to be full with only ~250 connections in the SYN_RECV state! Is it possible that the SYN flooding message is a red herring and it's something other than the syn_backlog that's filling up? If anyone has any other tuning options I haven't tried yet I'd be more than happy to try them out, but I'm starting to wonder if the syn_backlog setting isn't being applied properly for some reason.

  Read the article

• md/raid:md2: cannot start dirty degraded array, kernel panic

  - by nl-x

  After having made use of a remote power switch, my server did not come back online. When I went to the datacenter and reboot the computer on the spot I see the server booting (I see the centos progress bar with running almost all the way to the end) and eventually giving the following messages: md/raid:md2: cannot start dirty degraded array. md/raid:md2: failed to run raid set. md: pers->run() failed ... md/raid:md2: cannot start dirty degraded array. md/raid:md2: failed to run raid set. md: pers->run() failed ... Kernel panic - not syncing: Attempted to kill init! Pid: 1, comm: init not tainted 2.6.32-279.1.1.el6.i686 #1 Call Trace: [<c083bfbc>] ? panic+0x68/0x11c [<c045a501>] ? do_exit+0x741/0x750 [<c045a54c>] ? do_group_exit+0x3c/0xa0 [<c045a5c1>] ? sys_exit_group+0x11/0x20 [<c083eba4>] ? syscall_call+0x7/0xb [<c083007b>] ? cmos_wake_setup+0x62/0x112 The server runs CentOS and has software raid, and I don't have backups of the raid settings. The only backup I have is of /home and the database dumps. (Glad to at least have those though.) Since the server is an old Dell PowerEdge 1750 with no CD-ROM drive, I have no way of booting the machine from a boot disk. I also remember in the past that the server also wouldn't boot from a bootable USB disk. So the only way I know how to boot the server is to go to the datacenter, pick up the server and take it to the office. Screw open the server. Attach a cdrom drive to an IDE slot on the motherboard. And then boot it. I am hoping you guys could help me avoid this. I have looked a bit through the boot options and I found the following boot options. When CentOS is about to boot and interrupt the boot-countdown: CentOS (2.6.32-279.1.1.el63.i686) CentOS Linux (2.6.32-71.29.1.el6.i686) centos (2.6.32-71.el6.i686) I think the first configuration is the default one, because choosing that gets me to the above mentioned kernel panic. The other ones end with something like "Sleeping forever". I can press 'e' to edit boot commands, press 'a' to modify kernel arguments and press 'c' for grub command line. The command line gives a grub prompt. But I have no idea how to get the system to boot without (trying to) access the dirty partitions. What I want to do is off course: - boot the machine - check hard drive for errors - mark the drive as clean

  Read the article

• How to Eliminate Tape Backup and Off-site Storage Service?

  - by Daniel Lucas

  PLEASE READ UPDATE AT THE BOTTOM. THANKS! ;) Environment Info (all Windows): 2 sites 30 servers site #1 (3TB of backup data) 5 servers site #2 (1TB of backup data) MPLS backbone tunnel connecting site #1 and site #2 Current Backup Process: Online Backup (disk-to-disk) Site #1 has a server running Symantec Backup Exec 12.5 with four 1TB USB 2.0 disks. BE jobs for full backups run nightly on all servers in site #1 to these disks. Site #2 backs up to a central file server there using software they already had when we purchased them. A BE job pulls that data nightly to site #1 and stores them on said disks. Off-site Backup (tape) Connected to our backup server is a tape drive. BE backs up the external disks to tape once a week which gets picked up by our off-site storage company. Obviously we rotate two tape libraries, one is always here and one is always there. Requirements: Eliminate the need for tape and off-site storage service by doing disk-to-disk at each site and replicating site #1 to site #2 and vice versa. Software based solution as hardware options have been too pricey (ie, SonicWall, Arkeia). Agents for Exchange, SharePoint, and SQL. Some Ideas So Far: Storage DroboPro at each site with an initial 8TB of storage (these are expandable up to 16TB at present). I like these because they are rackmountable, allow disparate drives, and have iSCSI interfaces. They are relatively cheap too. Software Symantec Backup Exec 12.5 already has all the agents and licenses we need. I'd like to keep using it unless there is a better solution, similarly priced, that does everything BE does plus deduplication and replication. Server Because there is no more need for a SCSI adapter (for tape drive) we are going to virtualize our backup server as it is currently the only physical machine save for SQL boxes. Problems: When replicating between sites we want as little data as possible to go across the pipe. There is no deduplication or compression in what I have laid out here so far. The files being replicated are BE's virtual tape libraries from our disk-to-disk backup. Because of this each of those huge files will go across the wire every week because they change every day. And Finally, the Question: Is there any software out there that does deduplication, or at least compression, to handle just our site-to-site replication? Or, looking at our setup, is there any other solution that I am missing that might be cheaper, faster, better? Thanks. Sorry so long. UPDATE 2: I've set a bounty on this question to get it more attention. I'm looking for software that will handle replication of data between two sites using the least amount of data possible (either compression, deduplication, or some other method). Something similar to rsync would work but it needs to be native to Windows and not a port involving shenanigans to get up and running. Prefer a GUI based product and I don't mind shelling out a few bones if it works. Please, answers that meet the above criteria only. If you don't think one exists or if you think I'm being to restrictive keep it to yourself. If after seven days there is no answer at all, so be it. Thanks again everyone. UPDATE 2: I really appreciate everyone coming forward with suggestions. There is no way for me to try all of these before the bounty expires. For now I'm going to let this bounty run out and whoever has the most votes will get the 100 rep points. Thanks again!

  Read the article

• unattended-upgrades does not reboot

  - by Cheiron

  I am running Debian 7 stable with unattended-upgrades (every morning at 6 AM) to make sure I am always fully updated. I have the following config: $ cat /etc/apt/apt.conf.d/50unattended-upgrades // Automatically upgrade packages from these origin patterns Unattended-Upgrade::Origins-Pattern { // Archive or Suite based matching: // Note that this will silently match a different release after // migration to the specified archive (e.g. testing becomes the // new stable). "o=Debian,a=stable"; "o=Debian,a=stable-updates"; // "o=Debian,a=proposed-updates"; "origin=Debian,archive=stable,label=Debian-Security"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { // "vim"; // "libc6"; // "libc6-dev"; // "libc6-i686"; }; // This option allows you to control if on a unclean dpkg exit // unattended-upgrades will automatically run // dpkg --force-confold --configure -a // The default is true, to ensure updates keep getting installed //Unattended-Upgrade::AutoFixInterruptedDpkg "false"; // Split the upgrade into the smallest possible chunks so that // they can be interrupted with SIGUSR1. This makes the upgrade // a bit slower but it has the benefit that shutdown while a upgrade // is running is possible (with a small delay) //Unattended-Upgrade::MinimalSteps "true"; // Install all unattended-upgrades when the machine is shuting down // instead of doing it in the background while the machine is running // This will (obviously) make shutdown slower //Unattended-Upgrade::InstallOnShutdown "true"; // Send email to this address for problems or packages upgrades // If empty or unset then no email is sent, make sure that you // have a working mail setup on your system. A package that provides // 'mailx' must be installed. E.g. "[email protected]" Unattended-Upgrade::Mail "root"; // Set this value to "true" to get emails only on errors. Default // is to always send a mail if Unattended-Upgrade::Mail is set Unattended-Upgrade::MailOnlyOnError "true"; // Do automatic removal of new unused dependencies after the upgrade // (equivalent to apt-get autoremove) //Unattended-Upgrade::Remove-Unused-Dependencies "false"; // Automatically reboot *WITHOUT CONFIRMATION* if a // the file /var/run/reboot-required is found after the upgrade Unattended-Upgrade::Automatic-Reboot "true"; // Use apt bandwidth limit feature, this example limits the download // speed to 70kb/sec //Acquire::http::Dl-Limit "70"; As you can see Automatic-Reboot is true and thus the server should automaticly reboot. Last time I checked the server was online for over 100 days, which means that the update from Debian 7.1 to Debian 7.2 has happened while the server was up (and indeed, all updates were installed), but this involves kernel updates, which means that the server should reboot. It did not. The server was running very slow, so I rebooted which fixed that. I did some research and found out that unattended-upgrades responds to the reboot-required file in /var/run/. I touched this file and waited one week, the file still exists and the server did not reboot. So I think that unattended-uppgrades ignores the auto-reboot part. So, am I doing somthing wrong here? Why did the server not restart? The upgrade part works perfect by the way, its just the reboot part that does not seem to work as it should.

  Read the article

• Supermicro IPMI on MBD-X8DAH+-F-O motherboard. Keyboard and mouse do not work after booting Windows Server 2008 R2

  - by LDelgado

  Hell Everyone, I built a server with the mentioned motherboard. I installed Windows Server 2008 R2 Enterprise on this server. IPMI is integrated on the motherboard with its own dedicated NIC. I've got that NIC configured with its own IP address. I can remote into it using IPMI, and I can remotely control the server settings before booting the OS ( BIOS, RAID configuration, etc). When the OS boots, I lose the mouse and keyboard. I cannot use the keyboard or mouse when installing the OS either. So the Keyboard and Mouse only work when no OS is loaded. Once the OS loads I lose it - that is my problem. I've been doing some research and trying a few things, but I have not been successful in fixing this issue. I may be wrong, but based on the things I've found online, it seems that the problem could be caused by the way the OS handles USB. The server is headless. There is no keyboard, mouse, or monitor plugged into it. When I boot up the OS and remote into it, I cannot see a mouse or keyboard listed in the Device Manager. Based on what I've read, it seems that the OS should detect a mouse and a keyboard when connecting remotely via IPMI. The following are the solutions I've tried. Nothing has worked so far: I've updated the firmware of the IPMI component to the latest firmware - 1.33. I made sure that the mouse mode was set to Absolute (Windows OS). I've loaded the factory defaults several times. I've enabled Port64h/60h Emulation under the USB settings in the BIOS. I've disabled USB legacy support in the BIOS. I made sure the firewall wasn't blocking IPMI (disabled the firewall). And that's about it. I've found threads in some forums from people having the same issue as me, but they were not running the same OS. They were either running Linux or FreeBSD. Most of them fixed their problem by selecting the right mouse mode (Linux in their case). There was one other that solved the problem by disabling USB Mass Storage mode. He stated "When I set it to disable USB Mass Storage when no image is loaded, the ukbd came alive, and I'm typing this on the IPMI Console. " source: http://freebsd.1045724.n5.nabble.com/IPMI-Console-No-luck-once-OS-is-booted-td3967868.html I suspect the solution described in the previous paragraph is somehow related to my problem. I've found several threads on the internet with issues describing the same problem, but none of them were with Windows Server 2008 R2. Again, I may be wrong, but it seems like that could be the issue. I just don't know how I go about applying a solution in Windows Server 2008 R2. In any case, I could use your expertise. Maybe I am missing something, or maybe I'm on the right track. Your help is much appreciated. Thank you in advance,

  Read the article

• How do I reset/update my BIOS for Optiplex GX280?

  - by Sam Langlhey

  So far this has been a nightmare for me, which has been frustrating me constantly. I am using Dell Optiplex GX280 with Windows XP home edition, which is running a BIOS version A04. Recently, i've rebooted the pc to find out that its not booting. It will get to the Windows boot up screen with the progress bar but only to restart to the same process again, over and over. Frustrated that I am, i've inserted the Windows recovery CD to at least either repair of reinstall the operating system to find out that was not possible. I hit F8 to have the boot options, each of the boot option that I've selected gave me an error saying: "Selected boot device is not available." Right after that, I went to the BIOS setting and did a diagnostic test, which recognized all the Boot devices onboard. Now, I cannot even repair of reinstall Windows XP, because the system is not booting from none of the boot devices. The surprise is when I removed the hard-drive from the computer and loaded it on into another computer successfully; that's right, there is nothing wrong with the hard drive. After that I was totally puzzled. I found a few pointers online saying that the BIOS start-up block might be corrupted itself and I might need to flash/update the BIOS. I found the detailed instruction on how to create a Boot up disk by downloading the BIOS firmware from the manufacture's website. I did exactly as instructed below: Download the latest version or your choose version of BIOS file for your computer or motherboard from the manufacturer’s support site. Rename the downloaded file to AMIBOOT.ROM. Copy the file to a floppy disk. Insert the floppy disk to the floppy drive. Turn on the system. After I did that and powered on the PC to boot from the floppy drive, it gave me this error message: "Non-System Disk or Disk Error. Replace and Strike any key when ready." I did all that, and I kept on pressing [Ctrl]+[Home] to force it, but it did not did any satisfying result. Desperate as I am, my next attempt is to try the instruction below. Since I want to be ready, in the event it does not work, do you have any solution that you can provide? Please keep in mind that I cannot boot from any of the devices at this moment. My only hope now is to come on with a solution that will work through the Floppy drive, since that's the only drive that affected. Thank you very much for your advice and support in advance. To create a Windows startup disk, insert a floppy disk into the drive of a similarly configured, working Windows XP system, launch My Computer, right-click the floppy disk icon, and select the Format command from the context menu. When you see the Format dialog box, leave all the default settings as they are and click the Start button. Once the format operation is complete, close the Format dialog box to return to My Computer, double-click the drive C icon to access the root directory, and copy the following three files to the floppy disk: Boot.ini NTLDR Ntdetect.com

  Read the article

• How can I check if PHP was compiled with the UNICODE version of the Win32 API?

  - by Wesley Murch

  This is related to this Stack Overflow post: glob() can't find file names with multibyte characters on Windows? I'm having issues with PHP and files that have multibyte characters on Windows. Here's my test case: print_r(scandir('./uploads/')); print_r(glob('./uploads/*')); Correct Output on remote UNIX server: Array ( [0] => . [1] => .. [2] => filename-äöü.jpg [3] => filename.jpg [4] => test?test.jpg [5] => ??? ?????.jpg [6] => ?????????.jpg [7] => ???.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg [2] => ./uploads/test?test.jpg [3] => ./uploads/??? ?????.jpg [4] => ./uploads/?????????.jpg [5] => ./uploads/???.jpg ) Incorrect Output locally on Windows: Array ( [0] => . [1] => .. [2] => ??? ?????.jpg [3] => ???.jpg [4] => ?????????.jpg [5] => filename-äöü.jpg [6] => filename.jpg [7] => test?test.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg ) Here's a relevant excerpt from the answer I chose to accept (which actually is a quote from an article that was posted online over 2 years ago): From the comments on this article: http://www.rooftopsolutions.nl/blog/filesystem-encoding-and-php The output from your PHP installation on Windows is easy to explain : you installed the wrong version of PHP, and used a version not compiled to use the Unicode version of the Win32 API. For this reason, the filesystem calls used by PHP will use the legacy "ANSI" API and so the C/C++ libraries linked with this version of PHP will first try to convert yout UTF-8-encoded PHP string into the local "ANSI" codepage selected in the running environment (see the CHCP command before starting PHP from a command line window) Your version of Windows is MOST PROBABLY NOT responsible of this weird thing. Actually, this is YOUR version of PHP which is not compiled correctly, and that uses the legacy ANSI version of the Win32 API (for compatibility with the legacy 16-bit versions of Windows 95/98 whose filesystem support in the kernel actually had no direct support for Unicode, but used an internal conversion layer to convert Unicode to the local ANSI codepage before using the actual ANSI version of the API). Recompile PHP using the compiler option to use the UNICODE version of the Win32 API (which should be the default today, and anyway always the default for PHP installed on a server that will NEVER be Windows 95 or Windows 98...) I can't confirm whether this is my problem or not. I used phpinfo() and did not find anything interesting, but I wasn't sure what to look for. I've been using XAMPP for easy installations, so I'm really not sure exactly how it was installed. I'm using Windows 7, 64 bit - so forgive my ignorance, but I'm not even sure if "Win32" is relevant here. How can I check if my current version of PHP was compiled with the configuration mentioned above? PHP Version: 5.3.8 System: Windows NT WES-PC 6.1 build 7601 (Windows 7 Home Premium Edition Service Pack 1) i586 Build Date: Aug 23 2011 11:47:20 Compiler: MSVC9 (Visual C++ 2008) Architecture: x86 Configure Command: cscript /nologo configure.js "--enable-snapshot-build" "--disable-isapi" "--enable-debug-pack" "--disable-isapi" "--without-mssql" "--without-pdo-mssql" "--without-pi3web" "--with-pdo-oci=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8-11g=D:\php-sdk\oracle\instantclient11\sdk,shared" "--enable-object-out-dir=../obj/" "--enable-com-dotnet" "--with-mcrypt=static" "--disable-static-analyze"

  Read the article

• VMware vSphere cluster design for site redundancy

  - by Stefan Radovanovici

  I have a question about the best design for site redudancy when using vSphere clusters. A bit of background info about our situation first though. We are a medium-sized company with two main offices, located in different countries. Our networks are linked by a Layer2 150Mbps leased line which is currently underused. We have a variety of services running for internal use within the company, some on physycal servers and some on existing vSphere clusters. In our department we also run several services (almost all running under various forms of Linux) like NTP, Syslog, jump servers, monitoring servers and so on. We have now the requirement that those servers need to be redundant within each location (which they are not at the moment) and also site redudant (which they are to some extent, the servers are duplicated in the 2nd location with configurations kept in sync via various methods at the application layer). There is no SAN available for us, at least not something that we can use at the moment. Cost is also an issue. While we do have some budget available for this, we can't afford to buy SANs for both locations for example. I looked at the VSA feature and it seems that this could be something for us but I am unsure how to solve the site-redudancy requirement. At the moment for testing purposes I am setting up in a lab a vSphere 5 with VSA on two ESXi hosts. I am currently using the Essentials Plus kit with VSA license, which allows me to build a VSA cluster on up to 3 hosts, together with a vCenter license to manage them. The hosts each have two dual-port network cards and two 600GB drives, running in Raid1. Hardware-wise this will be enough for us to run the all the services we need as VMs and will provide redundandcy within the site. At the moment I see only two option to have site redundancy: build an identical VSA cluter in the second location and keep the various services sync'ed at application layer (database sync, rsync and so on). simply move one of the hosts from the existing cluster to the second location, basically having the VSA cluster span the 150Mbps link between the sites. I would very much prefer the second option but I am unsure how well it'll work, if it can work at all. Technically it should, we can span the needed VLANs across the leased line and have them available in the second location. The advantage would be that we don't need to worry at all about sync'ing databases and the like. But I have the feeling that the bandwidth will not be enough, I have no way of knowing how much traffic will the VSA cluster generate between the hosts. I realize that this will most likely depend on the individual usage of the VMs but still, I have no idea how VSA replicates data between the ESXi hosts. Are these my only options or can my goals be achieved in some other way ? Is there perhaps a way to have some sort of "cold stand by" cluster in the second location where the VMs would be sync'ed once per night from the main location ? The idea is that in case the first site becomes unavailable, we would be able to bring all those VMs online there. We would be ok with the data being 1 day old. Any answers are appreciated. Best regards, Stefan

  Read the article

• Do hard drive enclosures fail/is it the HDD or enclosure?

  - by x0a

  I'm having a whole host of problems with an external hard drive that was working just fine a couple of hours ago. I've had this problem before once, and that was about 3 months ago, here's what I documented: So a couple of hours ago I turned off all my computers and shut off the power to all my devices in my room, then went and turned the power off at the main switch so I could change an outlet. A couple hours later, after I've already slowly turned everything back on, I go to my xbox to try and watch a movie and it can't seem to list any of the movies I've got. So I go to my desktop to find that my external hard drive isn't there.. even though it's on and connected. It's also stationary and hidden behind something so there's not a whole lot of tampering/physical wear to that external. I plug it into my laptop to try and see what's going on. It starts making this endless loud screeching noise. None of that clicking that's usually associated with hd damage. It's not listed in my computers, and it shows up in Disk Management as "uninitialized" asking me to choose between two different partition types. After carefully disconnecting it and connecting it back, it asks me to format it, which I cancel. I start googling about my issue, starting to accept the situation, torn as hell and helpless and just about ready to toss the thing. Suddenly the screeching stops, after almost 45 minutes of it going, and Disk Management lists the drive as "Online" and "Healthy". Explorer pops up with all my files! I'm still being really careful with it and weary and treating it as though it's in fragile shape. I've downloaded some S.M.A.R.T. software to read the values and everything is listed as "OK" . No reallocated sectors, no read errors, no seek errors. I also ran a quick self-test, which completed without error. Everything seems fine. It looks to be a perfectly healthy external hard drive. So what the hell was that about? Was it doing some sort of maintenance or self-test? How am I supposed to tell the difference? I would've undoubtedly killed the drive for sure if had it gone on a bit longer. I've got the same problem now, with one exception: it doesn't magically reappear after the screeching stops. Occasionally I manage to get some S.M.A.R.T. diagnostics information, which basically reads everything as fine. The only problem is that my HD isn't initializing (so I can't access anything in it). I'm able to successfully run a quick smart test but not an extended one (I've only tried it once but got conflicting indications as to whether it was actually making any progress or not (was stuck on Random read test). So, final question (if all else fails): Could the hard drive enclosure be failing rather than the HDD? Is this a likely possibility at all? How would I know?

  Read the article

• Computer not POSTing "randomly"?

  - by smoth190

  I have a custom built PC that is exhibiting some...odd... behavior, something I've never seen before. It was working fine one day, and the next day, it wouldn't start. Seeing as I wanted an upgrade anyway, I purchased a new motherboard that was compatible with all my parts. While replacing the motherboard, I accidentally damaged the CPU. Well, I wanted a new one anyway... so I got a new one. Seeing as I was replacing a ton of parts already, I bought a new PSU because the old one was super loud. When I slapped it all together, it starts up, lights, fans, drives, they all start. But I get no display from the monitor. No beeps, which I believe means it doesn't POST. I figured it was the RAM, because after removing the sound card and graphics card, there was nothing else that I hadn't replaced. When I remove both sticks of RAM, I get a continuous beeping, and according to the mobo handbook, means no RAM. So I think the mobo is functional, or atleast partly. I bought new RAM, but it still didn't work. I tried 3 monitors, with both VGA and DIV. So it's probably not the monitor, either. Now, let me get to the random part. Every 20 or so boots (I should also mention, for about 3 out of 5 boots I have to unplug the PC because it won't powerdown via the button), it will POST and I'll get display. Then, after about 2 or 3 resets, it won't work again. This confuses me so much, because even when I change nothing, it will/will not work. My thought is that maybe it has something to do with the RAM not clearing or something. I also reset the CMOS battery, incase that had anything to do with it, but no eval. I found some weird suggestion online about holding the power button for 30 seconds while it was unplugged. That did nothing, but I didn't expect it would... I've replaced just about the entire computer, and all the parts are compatible. Done about everything I can think of, but nothing has worked. Hopefully someone can help me here. And as I side note: When I do get my computer to boot, it says my hardware has changed and I have to re-activate windows. But it says I have to call Microsoft to do it. So I get this fancy automated voice that asks me to enter in a code into windows, then it asks me "How many computers have you activated with this copy of Windows?". Well, I had it on my computer before I replaced everything, so I said 1. Then he yelled at me for violating my 1-use license. I dunno what's going on there, do I have to re-purchase Windows 7? And they wonder why people pirate software... That's just a bonus question, though. Specs: 8GB of DDR2 RAM (Corsair) AMD CPU (I don't know what GHz or model because I can't find the box... (I think its 4 cores of 2.8Ghz) ASRock A785GM-LE Motherboard

  Read the article

• What's the difference between find and findstr commands in Windows?

  - by Prashant Bhate

  In Windows, what are the differences between find and findstr commands? Both seems to search text in files: find c:\>find /? Searches for a text string in a file or files. FIND [/V] [/C] [/N] [/I] [/OFF[LINE]] "string" [[drive:][path]filename[ ...]] /V Displays all lines NOT containing the specified string. /C Displays only the count of lines containing the string. /N Displays line numbers with the displayed lines. /I Ignores the case of characters when searching for the string. /OFF[LINE] Do not skip files with offline attribute set. "string" Specifies the text string to find. [drive:][path]filename Specifies a file or files to search. If a path is not specified, FIND searches the text typed at the prompt or piped from another command. findstr c:\>findstr /? Searches for strings in files. FINDSTR [/B] [/E] [/L] [/R] [/S] [/I] [/X] [/V] [/N] [/M] [/O] [/P] [/F:file] [/C:string] [/G:file] [/D:dir list] [/A:color attributes] [/OFF[LINE]] strings [[drive:][path]filename[ ...]] /B Matches pattern if at the beginning of a line. /E Matches pattern if at the end of a line. /L Uses search strings literally. /R Uses search strings as regular expressions. /S Searches for matching files in the current directory and all subdirectories. /I Specifies that the search is not to be case-sensitive. /X Prints lines that match exactly. /V Prints only lines that do not contain a match. /N Prints the line number before each line that matches. /M Prints only the filename if a file contains a match. /O Prints character offset before each matching line. /P Skip files with non-printable characters. /OFF[LINE] Do not skip files with offline attribute set. /A:attr Specifies color attribute with two hex digits. See "color /?" /F:file Reads file list from the specified file(/ stands for console). /C:string Uses specified string as a literal search string. /G:file Gets search strings from the specified file(/ stands for console). /D:dir Search a semicolon delimited list of directories strings Text to be searched for. [drive:][path]filename Specifies a file or files to search. Use spaces to separate multiple search strings unless the argument is prefixed with /C. For example, 'FINDSTR "hello there" x.y' searches for "hello" or "there" in file x.y. 'FINDSTR /C:"hello there" x.y' searches for "hello there" in file x.y. Regular expression quick reference: . Wildcard: any character * Repeat: zero or more occurances of previous character or class ^ Line position: beginning of line $ Line position: end of line [class] Character class: any one character in set [^class] Inverse class: any one character not in set [x-y] Range: any characters within the specified range \x Escape: literal use of metacharacter x \<xyz Word position: beginning of word xyz\> Word position: end of word For full information on FINDSTR regular expressions refer to the online Command Reference.

  Read the article

• Capistrano + Nginx + Passenger = 403

  - by slimchrisp

  I asked this over at stackoverflow as well, but still haven't received any answers that have helped me to solve this problem. I have spent almost a week at this point trying to solve the issue, and I'm just not making any headway. It seems that this issue is pretty common, but none of the solutions I found online work for me. A buddy of mine is actually creating the same setup, and he is having the same issue. After a few days stuck with the 403 error I started over using this tutorial: http://blog.ninjahideout.com/posts/a-guide-to-a-nginx-passenger-and-rvm-server I had hoped starting from scratch using this tutorial would work, but no dice. Either way, if you view the tutorial you can see what steps I have taken. Here is essentially what I have going on. I have a VPS account on linode.com Server OS is Ubuntu 10.04 Local OS (shouldn't matter, but just so you know) used to deploy with Capistrano is Snow Leopard 10.6.6 I use RVM on the server. Version is 1.2.2 I was previously on ruby-1.9.2-p0 [ i386 ], but per the tutorial listed above I switched to ree-1.8.7-2010.02 [ i386 ]. Running 'which ruby' from the command line verifies that I am using 1.8.7 with the following output: /usr/local/rvm/rubies/ree-1.8.7-2010.02/bin/ruby passenger -v prints the following: Phusion Passenger version 3.0.2 Running 'nginx -v' gives me a message that the command nginx could not be found. The server is definitely there and running as I can use nginx to serve static files, but this could have something to do with my problem. I have two users dealing with the install. root which I used to install everything, and deployer which is a user I created specifically to for deploying my applications My web app directory is in the deployer user's home directory as follows: /home/deployer/webapps/mysite.com/public Per Capistrano default deploy, a symbolic link called current is created in the public folder, and points to /home/deployer/webapps/mysite.com/public/releases/most_current_release I have chmodded the deployer directory recursively to 777 /opt/nginx permissions: rwxr-xr-x /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2 permissions: rwxrwsrwx My nginx config file has gone through just short of eternity variations, but currently looks like this: ================================================================================== worker_processes 1; events { worker_connections 1024; } http { passenger_root /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2; passenger_ruby /usr/local/rvm/bin/passenger_ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { # listen *:80; server_name mysite.com www.mysite.com; root /home/deployer/webapps/mysite.com/public/current; passenger_enabled on; passenger_friendly_error_pages on; access_log logs/mysite.com/server.log; error_log logs/mysite.com/error.log info; error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } } ================================================================================== I bounce nginx, hit the site, and boom. 403, and logs say directory index of /home/deployer... is forbidden As others with a similar problem have said, you can drop an index.html into the public/releases/current_release and it will render. But rails no worky. That's basically it. At this point I have just about completely exhausted every possible solution attempt I can think of. I am a programmer and definitely not a sysadmin, so I am 99% sure this has something to do with permissions that I have hosed, but for the life of me I just can't figure out where. If anyone can help I would really really appreciate it. If there's any specific permission things you want me to check (ie groups/permissions), can you please include the commands to do so as well. Hopefully this will help others in the future who read this post. Let me know if there is any other information I can provide, and thanks in advance!!!

  Read the article

• BSOD Code 16, artifacts all over the place (gtx 260)

  - by belinea

  I have a following, quite dated rig E8400 Core 2 Duo cpu Intel Dragontail Peak DP35DP motherboard on Intel Bearlake P35 chipset 4GB ram Geforce 260gtx Corsair 650W PSU Windows 7 64 bit The following things has happened in the last few days. I first decided to update my Nvidia drivers to the latest version. That was 4 days ago. PC worked fine for 2 days and I was able to play few games as well without any problems. Then 2 days ago a first crash happened while playing the new XCOM game. BSOD code 16. Just the blue screen, no artifacts. PC rebooted and worked well again, I continued playing this game for another 2 hours and went to sleep. Next evening I tried to play some BF3 multiplayer (use to play on LOW settings). Approx. 10 minutes into the game red/pink-ish artifacts appeared on the screen and game quit to desktop. Restarted the game and another 3-4 minutes afterwards another crash to desktop but this time followed shortly by BSOD Code 16. From that moment I started to seeing artifacts on random startups, including Windows loading screen and the BIOS itself. Windows would still load but soon enough it would BSOD on a simple task like opening a Internet browser. Today I get tons of artifacts (little small red dashes all over the screen) on BIOS, loading screen, normal Windows mode as well as safe mode. I suspect it wouldn't be drivers but I tried removing and sweeping them entirely in the safe mode. PC would still start with artifacts all over the place but would load the normal mode, just without the driver, in the default lowest resolution. As soon as proper Nvidia drivers are installed though and PC rebooted, Windows doesn't load at all as BSOD now appears on loading screen. However, again, if I go to safe mode and remove drivers, normal mode launches fine. So obviously crash happens only on high resolution. I opened my machine this morning and gave it a proper cleaning even though it wasn't heavily dusted. It didn't help and number of artifacts seems to increase with every PC restart. I write these words in safe mode, which works, but I have to look through all the red dots and dashes. I don't have built in GPU chipset so I can't try removing my Geforce card nor can I borrow A GPU from anyone else. What are my options? I was looking into getting a completely new rig around Christmas so I'm not freaking out about this. If everything points to hardware issue I may simply decide to get the new machine earlier and don't bother with fixing this one. However it would be great to learn more if this is indeed situation that has slim chances of getting sorted. I realize BSOD Code 16 is rather popular topic online but every story seems a bit different and there can be number of issues with it. Hence a new thread.

  Read the article

• Debian dependency problems / partially installed

  - by Michael

  I tried to install curl support for php 5 on my debian squeeze machine and since I'm having problems. After trying to install curl I got dependency issues which I tried to solve by removing what started the issues. From one thing came another and I'm currently looking at ~29 issues when I try to do an apt-get upgrade. These issues vary from unable to config, dependency and unable to remove errors. I tried apt-get upgrade -f and installing packages using dpkg command. I tried removing using purge and force. I manually removed stuff to try and fix it. I tried running dpkg --configure -a. I've to say I'm still pretty new to linux so I'm out of idea's and cant seem to find an answer online that matches my problems. Here's a part of the apt-get upgrade command output: Reading package lists... Building dependency tree... Reading state information... 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 29 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up libgeoip1 (1.4.7~beta6+dfsg-1) ... Bus error dpkg: error processing libgeoip1 (--configure): subprocess installed post-installation script returned error exit status 135 Setting up libisc62 (1:9.7.3.dfsg-1~squeeze3) ... Bus error dpkg: error processing libisc62 (--configure): subprocess installed post-installation script returned error exit status 135 dpkg: dependency problems prevent configuration of libdns69: libdns69 depends on libgeoip1 (>= 1.4.7~beta6+dfsg); however: Package libgeoip1 is not configured yet. libdns69 depends on libisc62; however: Package libisc62 is not configured yet. dpkg: error processing libdns69 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libisccc60: libisccc60 depends on libisc62; however: Package libisc62 is not configured yet. dpkg: error processing libisccc60 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libisccfg62: libisccfg62 depends on libdns69; however: Package libdns69 is not configured yet. .. continues Errors were encountered while processing: libgeoip1 libisc62 libdns69 libisccc60 libisccfg62 libbind9-60 liblwres60 bind9-host libavahi-core7 libdaemon0 avahi-daemon libexif12 libffi5 libgomp1 libgphoto2-port0 libgphoto2-2 libperl5.10 libsensors4 libsnmp15 libhpmud0 libieee1284-3 libnss-mdns libossp-uuid16 libpq5 libv4l-0 libsane libsane-hpaio libssh2-1 python-gobject dpkg --configure -a Setting up libpq5 (8.4.8-0squeeze2) ... Bus error dpkg: error processing libpq5 (--configure): subprocess installed post-installation script returned error exit status 135 Setting up libperl5.10 (5.10.1-17squeeze2) ... Bus error dpkg: error processing libperl5.10 (--configure): subprocess installed post-installation script returned error exit status 135 Setting up libffi5 (3.0.9-3) ... Bus error dpkg: error processing libffi5 (--configure): subprocess installed post-installation script returned error exit status 135 Setting up libexif12 (0.6.19-1) ... .. continues Suggestions are really welcome I really don't know what to do. Michael.

  Read the article

< Previous Page | 362 363 364 365 366 367 368 369 370 371 372 373  | Next Page >