Search Results

Search found 9715 results on 389 pages for 'bad passwords'.

Page 368/389 | < Previous Page | 364 365 366 367 368 369 370 371 372 373 374 375  | Next Page >

• Getting hp-snmp-agents on HP ProLiant DL360 on Lenny working

  - by mark

  After receiving our HP ProLiant DL360 I'd like to integrate the machine into our Munin system and thus enable ProLiant specific information to be exposed via SNMP. I'm running Debian Lenny with kernel 2.6.26-2-vserver-amd64 . I've followed http://downloads.linux.hp.com/SDR/getting_started.html and the HP repository has been added to /etc/apt/sources.list.d/HP-ProLiantSupportPack.list . Setting up Lenny SNMP itself is not a problem, I configure it to have a public v1 community string to read all data and it works. I install hp-snmp-agents and run hpsnmpconfig and it adds additional lines to the top of /etc/snmp/snmpd.conf : dlmod cmaX /usr/lib64/libcmaX64.so snmpd gets restarted. Via lsof I can see that libcmaX64 was loaded and is used by snmpd, put I do not get any additional information out of snmp. I use snmpwalk -v 1 -c public ... and I can see many OIDs but I do not see the new ones I'd expect, most notably temperatures, fan speed and such. The OIDs I'm expecting are e.g. 1.3.6.1.4.1.232.6.2.6.8.1.4.1 , this is from the existing munin plugins from http://exchange.munin-monitoring.org/plugins/snmp__hp_temp/version/1 . snmpd[19007]: cmaX: Parsing shared as a type was unsucessful snmpd[19007]: cmaX: listening for subagents on port 25375 snmpd[19007]: cmaX: subMIB 1 handler has disconnected snmpd[19007]: cmaX: subMIB 2 handler has disconnected snmpd[19007]: cmaX: subMIB 3 handler has disconnected snmpd[19007]: cmaX: subMIB 5 handler has disconnected snmpd[19007]: cmaX: subMIB 6 handler has disconnected snmpd[19007]: cmaX: subMIB 8 handler has disconnected snmpd[19007]: cmaX: subMIB 9 handler has disconnected snmpd[19007]: cmaX: sent ColdStarts on ports 25376 to 25393 snmpd[19007]: cmaX: subMIB 10 handler has disconnected snmpd[19007]: cmaX: subMIB 11 handler has disconnected snmpd[19007]: cmaX: subMIB 14 handler has disconnected snmpd[19007]: cmaX: subMIB 15 handler has disconnected snmpd[19007]: cmaX: subMIB 16 handler has disconnected snmpd[19007]: cmaX: subMIB 21 handler has disconnected snmpd[19007]: cmaX: subMIB 22 handler has disconnected snmpd[19007]: cmaX: subMIB 23 handler has disconnected snmpd[19007]: cmaX: subMIB 1 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 2 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 3 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 5 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 6 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 8 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 9 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 10 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 11 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 14 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 15 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 16 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 21 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 22 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 23 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 18 handler has disconnected snmpd[19007]: cmaX: subMIB 18 will be sent on port 25393 to cpqnicd snmpd[19007]: NET-SNMP version 5.4.1 This doesn't look particular bad for me, it's just informational I guess. I've compared the walking OID output with and without the module and there's no difference in the OID served back at all. Are there any other prerequisites I'm missing? I've also noticed that from the time I installed hp-snmp-agents it adds a lot of additional daemons and that my load suddenly jumps to 1. I've uninstalled the package for now. Is this expected behavior?

  Read the article

• sendmail can not relay from itself

  - by Bernie

  I am running 3 centos 5.2 servers and I have configured the server for forward all messages to root to be emailed to me via .forward rule. This is working fine on two of the servers but not on the third. I have also tried copying the mail config files from the backup server and placing them on the file server and restarting sendmail. I also removed and reinstalled sendmail via yum but the results are the same. I am not sure what the issue could be they are all standard centos installs. Here is an example from the backup server which is working and the fileserver which isn't I am also going to include the mail log. good from backup server [root@backup ]# sendmail -v [email protected] < test.mail [email protected]... Connecting to [127.0.0.1] via relay... 220 backup.localhost ESMTP Sendmail 8.13.8/8.13.8; Fri, 16 Oct 2009 10:23:50 -0700 >>> EHLO backup.localhost 250-backup.localhost Hello backup.localhost [127.0.0.1], pleased to meet you 250-ENHANCEDSTATUSCODES 250-PIPELINING 250-8BITMIME 250-SIZE 250-DSN 250-ETRN 250-DELIVERBY 250 HELP >>> MAIL From:<[email protected]> SIZE=73 250 2.1.0 <[email protected]>... Sender ok >>> RCPT To:<[email protected]> >>> DATA 250 2.1.5 <[email protected]>... Recipient ok 354 Enter mail, end with "." on a line by itself >>> . 250 2.0.0 n9GHNoGC020924 Message accepted for delivery [email protected]... Sent (n9GHNoGC020924 Message accepted for delivery) Closing connection to [127.0.0.1] >>> QUIT 221 2.0.0 backup.localhost closing connection bad from file server [root@fileserver bernie]# sendmail -v [email protected] < test.mail [email protected]... Connecting to [127.0.0.1] via relay... 220 fileserver.localhost ESMTP Sendmail 8.13.8/8.13.8; Fri, 16 Oct 2009 10:23:26 -0700 >>> EHLO fileserver.localhost 250-fileserver.localhost Hello fileserver.localhost [127.0.0.1], pleased to meet you 250 ENHANCEDSTATUSCODES >>> MAIL From:<[email protected]> 550 5.0.0 Access denied root... Using cached ESMTP connection to [127.0.0.1] via relay... >>> RSET 250 2.0.0 Reset state >>> MAIL From:<> 550 5.0.0 Access denied postmaster... Using cached ESMTP connection to [127.0.0.1] via relay... >>> RSET 250 2.0.0 Reset state >>> MAIL From:<> 550 5.0.0 Access denied Closing connection to [127.0.0.1] >>> QUIT 221 2.0.0 fileserver.localhost closing connection mail log Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: from=root, size=72, class=0, nrcpts=1, msgid=<[email protected]>, relay=root@localhost Oct 16 10:39:13 fileserver sendmail[28060]: n9GHdDwl028060: tcpwrappers (fileserver.localhost, 127.0.0.1) rejection Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: [email protected], ctladdr=root (0/0), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30072, relay=[127.0.0.1] [127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: n9GHdDon028059: DSN: Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: to=root, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=31096, relay=[127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: n9GHdDoo028059: return to sender: Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDoo028059: to=postmaster, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=32120, relay=[127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: Losing ./qfn9GHdDon028059: savemail panic Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: SYSERR(root): savemail: cannot save rejected email anywhere

  Read the article

• Cisco VPN Client dropping connection

  - by IT Team

  Using Windows XP and Cisco VPN client version 5.0.4.xxx to connect to a remote customer site. We are able to establish the connection and start an RDP session, but within 1-2 minutes the connection drops and the VPN connection disconnects. The PC making the connection is on a DMZ which is NATed to a public IP address. If we move the PC directly onto the internet without being on the DMZ the connection works and we don't encounter any disconnects. We use a PIX 515E running 7.2.4 and don't have any problems with similar setups connecting to other customer sites from the DMZ. The VPN setup on the client side is pretty basic, using IPSec over TCP port 10000. Not sure what device they are using on the peer, but my guess would be an ASA. Any idea as to what the problem would be? Below is the logs from the VPN client when the problem occurs. The real IP address has been changed to: RemotePeerIP. 4 14:39:30.593 09/23/09 Sev=Info/4 CM/0x63100024 Attempt connection with server "RemotePeerIP" 5 14:39:30.593 09/23/09 Sev=Info/6 CM/0x6310002F Allocated local TCP port 1942 for TCP connection. 6 14:39:30.796 09/23/09 Sev=Info/4 IPSEC/0x63700008 IPSec driver successfully started 7 14:39:30.796 09/23/09 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 8 14:39:30.796 09/23/09 Sev=Info/6 IPSEC/0x6370002C Sent 256 packets, 0 were fragmented. 9 14:39:30.796 09/23/09 Sev=Info/6 IPSEC/0x63700020 TCP SYN sent to RemotePeerIP, src port 1942, dst port 10000 10 14:39:30.796 09/23/09 Sev=Info/6 IPSEC/0x6370001C TCP SYN-ACK received from RemotePeerIP, src port 10000, dst port 1942 11 14:39:30.796 09/23/09 Sev=Info/6 IPSEC/0x63700021 TCP ACK sent to RemotePeerIP, src port 1942, dst port 10000 12 14:39:30.796 09/23/09 Sev=Warning/3 IPSEC/0xA370001C Bad cTCP trailer, Rsvd 26984, Magic# 63697672h, trailer len 101, MajorVer 13, MinorVer 10 13 14:39:30.796 09/23/09 Sev=Info/4 CM/0x63100029 TCP connection established on port 10000 with server "RemotePeerIP" 14 14:39:31.296 09/23/09 Sev=Info/4 CM/0x63100024 Attempt connection with server "RemotePeerIP" 15 14:39:31.296 09/23/09 Sev=Info/6 IKE/0x6300003B Attempting to establish a connection with RemotePeerIP. 16 14:39:31.296 09/23/09 Sev=Info/4 IKE/0x63000013 SENDING ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Unity)) to RemotePeerIP 17 14:39:36.296 09/23/09 Sev=Info/4 IKE/0x63000021 Retransmitting last packet! 18 14:39:36.296 09/23/09 Sev=Info/4 IKE/0x63000013 SENDING ISAKMP OAK AG (Retransmission) to RemotePeerIP 19 14:39:41.296 09/23/09 Sev=Info/4 IKE/0x63000021 Retransmitting last packet! 20 14:39:41.296 09/23/09 Sev=Info/4 IKE/0x63000013 SENDING ISAKMP OAK AG (Retransmission) to RemotePeerIP 21 14:39:46.296 09/23/09 Sev=Info/4 IKE/0x63000021 Retransmitting last packet! 22 14:39:46.296 09/23/09 Sev=Info/4 IKE/0x63000013 SENDING ISAKMP OAK AG (Retransmission) to RemotePeerIP 23 14:39:51.328 09/23/09 Sev=Info/4 IKE/0x63000017 Marking IKE SA for deletion (I_Cookie=AEFC3FFF0405BBD6 R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING 24 14:39:51.828 09/23/09 Sev=Info/4 IKE/0x6300004B Discarding IKE SA negotiation (I_Cookie=AEFC3FFF0405BBD6 R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING 25 14:39:51.828 09/23/09 Sev=Info/4 CM/0x63100014 Unable to establish Phase 1 SA with server "RemotePeerIP" because of "DEL_REASON_PEER_NOT_RESPONDING" 26 14:39:51.828 09/23/09 Sev=Info/5 CM/0x63100025 Initializing CVPNDrv 27 14:39:51.828 09/23/09 Sev=Info/4 CM/0x6310002D Resetting TCP connection on port 10000 28 14:39:51.828 09/23/09 Sev=Info/6 CM/0x63100030 Removed local TCP port 1942 for TCP connection. 29 14:39:51.828 09/23/09 Sev=Info/6 CM/0x63100046 Set tunnel established flag in registry to 0. 30 14:39:51.828 09/23/09 Sev=Info/4 IKE/0x63000001 IKE received signal to terminate VPN connection 31 14:39:52.328 09/23/09 Sev=Info/6 IPSEC/0x63700023 TCP RST sent to RemotePeerIP, src port 1942, dst port 10000 32 14:39:52.328 09/23/09 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 33 14:39:52.328 09/23/09 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 34 14:39:52.328 09/23/09 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 35 14:39:52.328 09/23/09 Sev=Info/4 IPSEC/0x6370000A IPSec driver successfully stopped Thank you for any help you can provide.

  Read the article

• Windows 7 Samba issue

  - by abduls85

  We have a strange samba issue affecting only one user. Our samba setup is as follow : Red Hat Enterprise Linux Server release 5.4 (Tikanga) - Samba Server Samba version 3.0.33-3.14.el5 - Samba version Domain Controller WIN2008R2 Standard - Windows DC Windows 7 64 bit - Client PCs User mentioned that he faced this problem after he force shutdown his PC few weeks ago. By right, for all users when we access \\sambaservername in windows it will show all the shares in the samba server but for this user once he startup his PC he will not be able to access \\sambaservername, Error message Windows cannot access \\sambaservername Current workaround to solve the problem : Try to access one share in \\sambaservername for instance \\sambaservername\sharedfolder1. But even when doing so, it will first prompt an error in the beginning, error message is as follows Logon failure: unknown user name or bad password. user need to enter the credentials again and he can access the share. Thereafter, he will be able to access \\sambaservername without any issues. But once he reboots his computer the problem will persists. Troubleshooting done so far: Ensure the following settings: Go to: Control Panel → Administrative Tools → Local Security Policy Select: Local Policies → Security Options "Network security: LAN Manager authentication level" → Send LM & NTLM responses "Minimum session security for NTLM SSP" → uncheck: Require 128-bit encryption Advise user to reset his password and try again but problem still persists Tried my account on users' PC, there is no issues. Tried user account on serveral other Windows 7 PC including mine but problem still persists. Windows XP does not have this problem. Ensure that there is no stored crendentials on the windows 7 PC. Checked the credentials manager in Control Panel as well as typing this command rundll32.exe keymgr.dll, KRShowKeyMgr Restart winbindd daemon on samba server but to no avail. I suspect this is due to some caching issue but not sure where is the issue. Whenever the user has error accessing \\sambaservername, the following errors will be logged in the samba server : [2012/10/10 17:10:26, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! But after workaround, there will be no more errors. I suspect after reading the article listed below some amendments need to be made to the \var\samba\cache directory : http://www.linuxquestions.org/questions/linux-server-73/getent-passwd-dont-show-ad-groups-and-users-745829/ http://www.samba.org/samba/docs/man/Samba-HOWTO-Collection/tdb.html http://lists.samba.org/archive/samba/2010-May/155521.html http://lists.samba.org/archive/samba/2011-March/161912.html http://lzeit.blogspot.sg/2009/10/samba-shares-inaccessible-after-power.html There are several users using the samba server and i would like to solve this problem without any impacts. I saw the following article : http://www.samba.org/samba/docs/man/manpages-3/smb.conf.5.html#WINBINDCACHETIME "winbind offline logon (G) This parameter is designed to control whether Winbind should allow to login with the pam_winbind module using Cached Credentials. If enabled, winbindd will store user credentials from successful logins encrypted in a local cache. Default: winbind offline logon = false Example: winbind offline logon = true " Any idea on how to delete the entry for one user in the local cache ?

  Read the article

• Dual head setup for Ubuntu 10.04.1 and Windows XP Pro with same hardware configuration

  - by mejpark

  Hello. I have a Dell OptiPlex 360 workstation at work, with 2 x ATI RV280 [Radeon 9200 PRO] graphics cards installed, which are attached to two identical 19" HII flat panel monitors. I'm using the open source Radeon driver with Ubuntu, and the proprietary drivers with Windows. The good news is that dual head configuration works for both OSes. The bad news is, I have to use a different hardware configuration for each OS to achieve this. Hardware config #1: Dual monitors work for Windows XP Pro like this: First display -> external VGA port Second display -> DVI input on gfx card Hardware config #2: Dual monitors work for Ubuntu 10.04.1 like this: First display -> VGA port on gfx card Second display -> DVI input on gfx card I connected up the displays according to Config #2 and booted up Windows, which resulted in a mirror image on both screens. I was unable to login, as the login box was not visible. I unplugged the VGA lead from gfx card and plugged it into the external VGA port (Config #1) - Windows dual head works again, but the VGA-connected screen is not recognised by Ubuntu and remains in standby mode. Is it possible to configure a dual head setup for Ubuntu using Config #1, or am I missing something? I tried setting up dual monitors using Config #1, this morning which didn't work. By default, there is no xorg.conf file in Ubuntu 10.04.1, so I generated one using: $ sudo X :2 -configure X.Org X Server 1.7.6 Release Date: 2010-03-17 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-27-server i686 Ubuntu Current Operating System: Linux harrier 2.6.32-24-generic #42-Ubuntu SMP Fri Aug 20 14:24:04 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-24-generic root=UUID=a34c1931-98d4-4a34-880c-c227a2936c4a ro quiet splash Build Date: 21 July 2010 12:47:34PM xorg-server 2:1.7.6-2ubuntu7.3 (For technical support please see http://www.ubuntu.com/support) Current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.2.log", Time: Mon Sep 13 10:02:02 2010 List of video drivers: apm ark intel mach64 s3virge trident mga tseng ati nouveau neomagic i740 openchrome voodoo s3 i128 radeon siliconmotion nv ztv vmware v4l chips rendition savage sisusb tdfx geode sis r128 cirrus fbdev vesa (++) Using config file: "/home/michael/xorg.conf.new" (==) Using config directory: "/usr/lib/X11/xorg.conf.d" (II) [KMS] No DRICreatePCIBusID symbol, no kernel modesetting. Xorg detected your mouse at device /dev/input/mice. Please check your config if the mouse is still not operational, as by default Xorg tries to autodetect the protocol. Xorg has configured a multihead system, please check your config. Your xorg.conf file is /home/michael/xorg.conf.new To test the server, run 'X -config /home/michael/xorg.conf.new' ddxSigGiveUp: Closing log $ sudo X -config /home/michael/xorg.conf.new Fatal server error: Server is already active for display 0 If this server is no longer running, remove /tmp/.X0-lock and start again. Please consult the The X.Org Foundation support at http://wiki.x.org for help. ddxSigGiveUp: Closing log I then booted Ubuntu in failsafe mode, dropped into root shell, and executed $ X -config /home/michael/xorg.conf.new again. The screen went blank and turned off, so I reset the machine. There must be a way round this. Any help to set up a dual head config for Ubuntu using Config #1 would be hugely appreciated. TIA, Mike

  Read the article

• Sharing the same `ssh-agent` among multiple login sessions

  - by intuited

  Is there a convenient way to ensure that all logins from a given user (ie me) use the same ssh-agent? I hacked out a script to make this work most of the time, but I suspected all along that there was some way to do it that I had just missed. Additionally, since that time there have been amazing advances in computing technology, like for example this website. So the goal here is that whenever I log in to the box, regardless of whether it's via SSH, or in a graphical session started from gdm/kdm/etc, or at a console: if my username does not currently have an ssh-agent running, one is started, the environment variables exported, and ssh-add called. otherwise, the existing agent's coordinates are exported in the login session's environment variables. This facility is especially valuable when the box in question is used as a relay point when sshing into a third box. In this case it avoids having to type in the private key's passphrase every time you ssh in and then want to, for example, do git push or something. The script given below does this mostly reliably, although it botched recently when X crashed and I then started another graphical session. There might have been other screwiness going on in that instance. Here's my bad-is-good script. I source this from my .bashrc. # ssh-agent-procure.bash # v0.6.4 # ensures that all shells sourcing this file in profile/rc scripts use the same ssh-agent. # copyright me, now; licensed under the DWTFYWT license. mkdir -p "$HOME/etc/ssh"; function ssh-procure-launch-agent { eval `ssh-agent -s -a ~/etc/ssh/ssh-agent-socket`; ssh-add; } if [ ! $SSH_AGENT_PID ]; then if [ -e ~/etc/ssh/ssh-agent-socket ] ; then SSH_AGENT_PID=`ps -fC ssh-agent |grep 'etc/ssh/ssh-agent-socket' |sed -r 's/^\S+\s+(\S+).*$/\1/'`; if [[ $SSH_AGENT_PID =~ [0-9]+ ]]; then # in this case the agent has already been launched and we are just attaching to it. ##++ It should check that this pid is actually active & belongs to an ssh instance export SSH_AGENT_PID; SSH_AUTH_SOCK=~/etc/ssh/ssh-agent-socket; export SSH_AUTH_SOCK; else # in this case there is no agent running, so the socket file is left over from a graceless agent termination. rm ~/etc/ssh/ssh-agent-socket; ssh-procure-launch-agent; fi; else ssh-procure-launch-agent; fi; fi; Please tell me there's a better way to do this. Also please don't nitpick the inconsistencies/gaffes ( eg putting var stuff in etc ); I wrote this a while ago and have since learned many things.

  Read the article

• Useful Command-line Commands on Windows

  - by Sung Meister

  The aim for this Wiki is to promote using a command to open up commonly used applications without having to go through many mouse clicks - thus saving time on monitoring and troubleshooting Windows machines. Answer entries need to specify Application name Commands Screenshot (Optional) Shortcut to commands && - Command Chaining %SYSTEMROOT%\System32\rcimlby.exe -LaunchRA - Remote Assistance (Windows XP) appwiz.cpl - Programs and Features (Formerly Known as "Add or Remove Programs") appwiz.cpl @,2 - Turn Windows Features On and Off (Add/Remove Windows Components pane) arp - Displays and modifies the IP-to-Physical address translation tables used by address resolution protocol (ARP) at - Schedule tasks either locally or remotely without using Scheduled Tasks bootsect.exe - Updates the master boot code for hard disk partitions to switch between BOOTMGR and NTLDR cacls - Change Access Control List (ACL) permissions on a directory, its subcontents, or files calc - Calculator chkdsk - Check/Fix the disk surface for physical errors or bad sectors cipher - Displays or alters the encryption of directories [files] on NTFS partitions cleanmgr.exe - Disk Cleanup clip - Redirects output of command line tools to the Windows clipboard cls - clear the command line screen cmd /k - Run command with command extensions enabled color - Sets the default console foreground and background colors in console command.com - Default Operating System Shell compmgmt.msc - Computer Management control.exe /name Microsoft.NetworkAndSharingCenter - Network and Sharing Center control keyboard - Keyboard Properties control mouse(or main.cpl) - Mouse Properties control sysdm.cpl,@0,3 - Advanced Tab of the System Properties dialog control userpasswords2 - Opens the classic User Accounts dialog desk.cpl - opens the display properties devmgmt.msc - Device Manager diskmgmt.msc - Disk Management diskpart - Disk management from the command line dsa.msc - Opens active directory users and computers dsquery - Finds any objects in the directory according to criteria dxdiag - DirectX Diagnostic Tool eventvwr - Windows Event Log (Event Viewer) explorer . - Open explorer with the current folder selected. explorer /e, . - Open explorer, with folder tree, with current folder selected. F7 - View command history find - Searches for a text string in a file or files findstr - Find a string in a file firewall.cpl - Opens the Windows Firewall settings fsmgmt.msc - Shared Folders fsutil - Perform tasks related to FAT and NTFS file systems ftp - Transfers files to and from a computer running an FTP server service getmac - Shows the mac address(es) of your network adapter(s) gpedit.msc - Group Policy Editor gpresult - Displays the Resultant Set of Policy (RSoP) information for a target user and computer httpcfg.exe - HTTP Configuration Utility iisreset - To restart IIS InetMgr.exe - Internet Information Services (IIS) Manager 7 InetMgr6.exe - Internet Information Services (IIS) Manager 6 intl.cpl - Regional and Language Options ipconfig - Internet protocol configuration lusrmgr.msc - Local Users and Groups Administrator msconfig - System Configuration notepad - Notepad? ;) mmsys.cpl - Sound/Recording/Playback properties mode - Configure system devices more - Displays one screen of output at a time mrt - Microsoft Windows Malicious Software Removal Tool mstsc.exe - Remote Desktop Connection nbstat - displays protocol statistics and current TCP/IP connections using NBT ncpa.cpl - Network Connections netsh - Display or modify the network configuration of a computer that is currently running netstat - Network Statistics net statistics - Check computer up time net stop - Stops a running service. net use - Connects a computer to or disconnects a computer from a shared resource, or displays information about computer connections odbcad32.exe - ODBC Data Source Administrator pathping - A traceroute that collects detailed packet loss stats perfmon - Opens Reliability and Performance Monitor ping - Determine whether a remote computer is accessible over the network powercfg.cpl - Power management control panel applet quser - Display information about user sessions on a terminal server qwinsta - See disconnected remote desktop sessions reg.exe - Console Registry Tool for Windows regedit - Registry Editor rasdial - Connects to a VPN or a dialup network robocopy - Backup/Restore/Copy large amounts of files reliably rsop.msc - Resultant Set of Policy (shows the combined effect of all group policies active on the current system/login) runas - Run specific tools and programs with different permissions than the user's current logon provides sc - Manage anything you want to do with services. schtasks - Enables an administrator to create, delete, query, change, run and end scheduled tasks on a local or remote system. secpol.msc - Local Security Settings services.msc - Services control panel set - Displays, sets, or removes cmd.exe environment variables. set DIRCMD - Preset dir parameter in cmd.exe start - Starts a separate window to run a specified program or command start. - opens the current directory in the Windows Explorer. shutdown.exe - Shutdown or Reboot a local/remote machine subst.exe - Associates a path with a drive letter, including local drives systeminfo -Displays a comprehensive information about the system taskkill - terminate tasks by process id (PID) or image name tasklist.exe - List Processes on local or a remote machine taskmgr.exe - Task Manager telephon.cpl - Telephone and Modem properties timedate.cpl - Date and Time title - Change the title of the CMD window you have open tracert - Trace route wmic - Windows Management Instrumentation Command-line winver.exe - Find Windows Version wscui.cpl - Windows Security Center wuauclt.exe - Windows Update AutoUpdate Client

  Read the article

• Increase samba space on open suse 12.1

  - by Kapil Sharma

  I know linux basics but not an expert. IT guy left the job here and there is some time before new hire. So sorry if question is very basic. We have local testing server based on Open SUSE 12.1, which also act as shared drive between dev/mgmt team here and using Samba for that. Now we are running out of space on samba, even though server's 2*1TB harddisk is nearly 90% free. My question is, what is limiting Samba and how can I increase its limit? We need around at least 500 GB as shared drive but currently its just 25 GB. I don't need step by step answer, just a link to any helpful article would be sufficient. Probably I'm putting wrong keywords in google so not getting any helpful link. EDIT: Output of commands in the first comment. All commands were run as root user df -h (getting error with df -ht) Filesystem Size Used Avail Use% Mounted on rootfs 30G 5.1G 23G 19% / devtmpfs 2.0G 36K 2.0G 1% /dev tmpfs 2.0G 1.1M 2.0G 1% /dev/shm tmpfs 2.0G 676K 2.0G 1% /run /dev/sda2 30G 5.1G 23G 19% / tmpfs 2.0G 0 2.0G 0% /sys/fs/cgroup tmpfs 2.0G 676K 2.0G 1% /var/run tmpfs 2.0G 0 2.0G 0% /media tmpfs 2.0G 676K 2.0G 1% /var/lock /dev/sda3 36G 31G 3.3G 91% /home fdisk -l /dev/[hmsv]d* Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x2d4a2d49 Device Boot Start End Blocks Id System /dev/sda1 2048 16771071 8384512 82 Linux swap / Solaris /dev/sda2 * 16771072 79681535 31455232 83 Linux /dev/sda3 79681536 156301311 38309888 83 Linux Disk /dev/sda1: 8585 MB, 8585740288 bytes 255 heads, 63 sectors/track, 1043 cylinders, total 16769024 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 32.2 GB, 32210157568 bytes 255 heads, 63 sectors/track, 3915 cylinders, total 62910464 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System Disk /dev/sda3: 39.2 GB, 39229325312 bytes 255 heads, 63 sectors/track, 4769 cylinders, total 76619776 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda3 doesn't contain a valid partition table vgs No volume groups found lvs No volume groups found output of vi /etc/samba/smb.conf # smb.conf is the main Samba configuration file. You find a full commented # version at /usr/share/doc/packages/samba/examples/smb.conf.SUSE if the # samba-doc package is installed. # Date: 2011-11-02 [global] workgroup = WORKGROUP passdb backend = tdbsam printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User include = /etc/samba/dhcp.conf logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = Yes [homes] comment = Home Directories valid users = %S, %D%w%S browseable = No read only = No inherit acls = Yes [profiles] comment = Network Profiles Service path = %H read only = No store dos attributes = Yes create mask = 0600 directory mask = 0700 [users] comment = All users path = /home read only = No inherit acls = Yes veto files = /aquota.user/groups/shares/ [groups] comment = All groups path = /home/groups read only = No inherit acls = Yes [printers] comment = All Printers path = /var/tmp printable = Yes create mask = 0600 browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/drivers write list = @ntadmin root force group = ntadmin create mask = 0664 directory mask = 0775 [allusers] comment = All Users path = /home/shares/allusers valid users = @users force group = users create mask = 0660 directory mask = 0771 writable = yes

  Read the article

• Cannot ping host stale ARP cache?

  - by gkchicago

  I am having a strange issue with a Debian (Lenny/Linux 2.6.26-2-amd64) that has been driving me nuts. On some machines within my network I can ping the host in question just fine, other times I have to manually hard-code the ARP ethernet address for the IP in order to establish connectivity. I've finally worked it down to somehow involving ARP. I just found how to fix it in a way that made it work but I'm looking for help explaining this issue and also I don't trust my fix to be permanent.. My thought process has been the following but I just can't make any sense out of it: Could it be the card? (Intel 82555 rev 4) Could it be because there are two network cards? (Default route is eth0) Could it be because of the network aliases? Lenny? AMD x86_64? Argh.. Thank you for any insight you might have // Ping doesn't go thru [gordon@ubuntu ~]$ ping 192.168.135.101 PING 192.168.135.101 (192.168.135.101) 56(84) bytes of data. --- 192.168.135.101 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3014ms // Here's the ARP Table, sometimes the .151 address is good, sometimes it // also matches the Gateways MAC like .101 is doing right here. [gordon@ubuntu ~]$ cat /proc/net/arp IP address HW type Flags HW address Mask Device 192.168.135.15 0x1 0x2 00:0B:DB:2B:24:89 * eth0 192.168.135.151 0x1 0x2 00:0B:6A:3A:30:A6 * eth0 192.168.135.1 0x1 0x2 00:1A:A2:2D:2A:04 * eth0 192.168.135.101 0x1 0x2 00:1A:A2:2D:2A:04 * eth0 // Drop the bad arp table listing and set it manually based on /sbin/ifconfig [gordon@ubuntu ~]$ sudo arp -d 192.168.135.101 [gordon@ubuntu ~]$ sudo arp -s 192.168.135.101 00:0B:6A:3A:30:A6 // Ping starts going thru..?!? [gordon@ubuntu ~]$ ping 192.168.135.101 PING 192.168.135.101 (192.168.135.101) 56(84) bytes of data. 64 bytes from 192.168.135.101: icmp_seq=1 ttl=64 time=15.8 ms 64 bytes from 192.168.135.101: icmp_seq=2 ttl=64 time=15.9 ms 64 bytes from 192.168.135.101: icmp_seq=3 ttl=64 time=16.0 ms 64 bytes from 192.168.135.101: icmp_seq=4 ttl=64 time=15.9 ms --- 192.168.135.101 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3012ms rtt min/avg/max/mdev = 15.836/15.943/16.064/0.121 ms The following is my network config on this. gordon@db01:~$ /sbin/ifconfig eth0 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.151 Bcast:192.168.135.255 Mask:255.255.255.0 inet6 addr: fe80::20b:6aff:fe3a:30a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15476725 errors:0 dropped:0 overruns:0 frame:0 TX packets:10030036 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18565307359 (17.2 GiB) TX bytes:3412098075 (3.1 GiB) eth0:0 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.150 Bcast:192.168.135.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:1 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.101 Bcast:192.168.135.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth1 Link encap:Ethernet HWaddr 00:e0:81:2a:6e:d0 inet addr:10.10.62.1 Bcast:10.10.62.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe2a:6ed0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10233315 errors:0 dropped:0 overruns:0 frame:0 TX packets:19400286 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1112500658 (1.0 GiB) TX bytes:27952809020 (26.0 GiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:387 errors:0 dropped:0 overruns:0 frame:0 TX packets:387 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:41314 (40.3 KiB) TX bytes:41314 (40.3 KiB) gordon@db01:~$ sudo mii-tool -v eth0 eth0: negotiated 100baseTx-FD, link ok product info: Intel 82555 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD gordon@db01:~$ sudo route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface localnet * 255.255.255.0 U 0 0 0 eth0 10.10.62.0 * 255.255.255.0 U 0 0 0 eth1 default 192.168.135.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Why do GPUs overheat?

  - by JAD

  About a year ago, I added a 9800GT (1 GB version) and a Corsair CX500 PSU to an HP M8000N computer. A few weeks ago, the HDD overheated and I decided to transfer the GPU & PSU to a new build, which consists of: i3 @ 3.3Ghz Gigabyte H61 Micro ATX Mobo 4GB RAM 500GB WD HDD DVD RW Drive Cooler Master Elite 430 Tower Once I had Win7 up and running, I installed all the essential drivers that came with the Gigabyte Mobo CD. However, whenever I tried installing the Graphics Media Accelerator driver, the computer would crash and enter an endless boot sequence on the next startup. I skipped installing this driver and installed the CD driver for the 9800GT, which by now is a year old. Everything was working fine, WEI rated my GPU at 6.6 graphics & aero performance. However, after updating my Nvidia drivers to the latest, the WEI dropped my rating to 3.3 for Aero, and 4.7 for graphics performance. Just to make sure that everything was ok, I ran Bad Company 2 on medium settings. The first few minutes ran just fine at a smooth framerate, so I dismissed this as Windows being Windows. About 6 hours later, I ran BC2 again. This time I averaged anywhere from 2-5 FPS. I checked the GPU temperature through GPU-Z, and it came back as 120C. The problem with this, is that the computer was on for six hours up to that point. Wouldn't the card have experienced a reactor core meltdown a lot sooner than that? Granted, the computer was "sleeping" some of the time, but still... The next day I took out a temperature gun and ran some tests. I would point the laser at a very specific area on the reverse side of the card (not the fan or "front"), and compare the temp reading with GPU-Z. After leaving the system on idle on idle for a few minutes, I ran BC2 twice. Here are the results: GPU-Z Reading / Temp Gun Reading / Time Null / 22.3°C / Comp is Off 53°C / 33.5°C / 1:49 78°C / 46°C / 1:53 - (First BC2 run; good framerate) 102°C / 64.6°C / 2:01 - (System is again on idle) 113°C / 64.8°C / 2:10 119°C / 71.8°C / 2:17 - (Second BC2 run; poor framerate) I should also mention that I also took a temp recording of another part of the GPU from 2:01-2:17. The temp in this area jumped from 75°C to 82.9°C in that time frame. This pretty much confirms that GPU-Z is reporting the temperature accurately, and the card is overheating. But I'd like to know why; the cars is doing nothing and still the temperature climbs at a steady rate. I thoroughly cleaned the GPU and PSU when I salvaged them from the old HP M8000N computer with a can of compressed air, dust cant be the issue. Similarly, the rest of the computer is brand new. I installed various Nvidia drivers, but no luck. It seems strange to me that a year-old card is suddenly failing on me; aren't they supposed to last at least two years? Could this be a driver issue? Is the motherboard faulty? Could the PSU be overfeeding the card on voltage? Neither case seems likely, as the CPU, RAM and otherwise the rest of the comp has worked flawlessly and has stayed well within respectable temp ranges (the i3 lingers around 50C, the HDD stays at 30C, so does the PSU). How can I pinpoint the issue?

  Read the article

• DHCP and DNS services configuration for VOIP system, windows domain, etc

  - by Stemen

  My company has numerous physical offices (for purposes of this discussion, 15 buildings). Some of them are well-connected to our primary data center via fiber. Others will be connected to the data center by P2P T1. We are in the beginning stages of implementing an Avaya VOIP telephone system, and we will be replacing a significant portion of our network infrastructure in the process. In tandem with the phone system implementation, we are going to be re-addressing some of our networks, and consolidating most of our Windows domains into one (not all domains, just most). We currently have quite a few Windows domains, and they of course each have their own DNS zones. A few of those networks currently use DHCP, but the majority use static IP assignments for every device. I'm tired of managing static assignments -- I want to use DHCP configuration on everything except servers. Printers and etc will have DHCP reservations. The new IP phones will need to get IP addresses from DHCP, though they need to be in a separate VLAN from the computers/printers/etc. The computers and printers need to be registered in DNS. That's currently handled by the Windows DHCP servers on each of the respective domains. We need to place a priority on DHCP and DNS being available on a per-site basis (in case something were to interrupt the WAN connection) for computers and (primarily) phones. Smaller locations (which will have IP phones but not be a member of any Windows domain) will not have any Windows DNS/DHCP server(s) available. We also are looking for the easiest way to replace a part if it were to fail. That is to say, if a server/appliance/router hosting DHCP were to crash hard, and we couldn't extremely quickly recover the DHCP reservations and leases (and subsequently restore them onto a cold spare), we anticipate that bad things could happen. What is the best idea for how to re-implement DNS and DHCP keeping all of the above in mind? Some thoughts that have been raised (by myself or my coworkers): Use Windows DNS and DHCP servers, where they exist, and use IP helpers to route DHCP requests to some other Windows server if necessary. May not be acceptable if the WAN goes down and clients don't get a DHCP response. Use Windows DNS (everywhere, over WAN in some cases) and a mix of Windows DHCP and DHCP provided by Cisco routers. Every site would be covered for DHCP, but from what I've read, Cisco routers can't handle dynamic registration of DHCP clients to Windows DNS servers, which might create a problem where Cisco routers are used for DHCP. Use Windows DNS (everywhere, over WAN in some cases) and a mix of Windows DHCP and DHCP provided by some service running on an extremely low-price linux server. Is there any such software that would allow DHCP leases granted by these linux boxes to be dynamically registered on the Windows DNS servers? Come up with a Linux solution for both DNS and DHCP, and deploy low-price linux servers to every site. Requirements would be that the DNS zone be multi-master (like Windows DNS integrated with Active Directory), that DHCP be able to make dynamic DNS registrations in that zone, for every lease (where a hostname is provided and is thus possible), and that multiple servers be either authoritative for the same DHCP scope or at least receiving a real-time copy / replication / sync of the leases table so that if one server dies, we still know which MAC has what address. Purchase dedicated DNS/DHCP appliances, deploying to all sites. From what I read/see, this solves all of our technical problems. Then come the financial problems... I don't have a ton of money to spend on this. Or, some other solution that we've thus far overlooked and will consider upon recommendation. Can Cisco routers or Windows servers sync DHCP lease tables so that multiple servers can be authoritative (or active/passive for all I care) for the same scope, in case one of the partners were to fail? I've read online (repeatedly) that ISC's DHCP is able to maintain the same lease table across multiple servers, in order to solve this problem. Does anyone have any experience or advice to regarding that?

  Read the article

• Windows 7 .NET 3.5.1 - 2.0 Slightly Corrupted, How to Repair?

  - by Quinxy von Besiex

  My Windows 7 included .NET installation (3.5 to 2.0) appears very slightly and particularly corrupted and I am trying to fix it without reinstalling Windows or trying to revert to backups. Everything was working and then my hard drive started corrupting a few files and checkdisk found bad clusters so I imaged the drive to a new one. As soon as I booted on the new drive everything worked except programs which call the System.Net.NetworkInformation methods within .NET 3.5 to 2.0 (like Ping() and IsNetworkAvailable()), which immediately crash the app in which the calls are (those calls in .NET 4.0 works fine). Those methods are found inside System.dll, and I assume call native methods which I believe are inside winnsi.dll or iphlpapi.dll or something else (I've not found this yet); I assume it calls native methods because the exception which causes the crash is Fatal Execution Engine Error which people mention is usually related to calling native methods and marshaling data between them. A huge clue about the culprit is likely found in the fact that when I launch the exact same crashing application through a code profiler (which executes the exe and captures stats on which methods took the longest) the app works fine, no crash at all! How could running it within the profiler work and running it outside not work? That seems the key to the mystery. I've used procmon to catch all the registry, filesystem, and network events from the crashing execution and the profiler-run successful execution and compared the two outputs but didn't learn much (I see the moment at which the non-profiled app crashes, but up until then they behave the same, loaded the same modules, ). The only big difference seems to be that at the moment before the app crash the profiler-executed code creates 4-6 new threads and the directly executed code only creates 1-2. I have diffed the files/directories which seemed most relevant (the .NET stuff under Windows and Program Files) pre- and post- disk trouble and seen no changes where I didn't expect any (no obvious file corruption). I have diffed the software and system registry hives pre- and post- disk trouble and seen no changes which seemed relevant. I have created a new user account and cleaned up any environment variables in case environment was related. No change. I did "sfc /scannow" and it found no integrity problems. I tried "ngen update" to regenerate pre-compiled code in case I missed something that might be damaged and nothing changed. I assume I need to repair my .NET installation but because Windows 7 included .NET 3.5 - 2.0 you can't just re-run a .NET installer to redo it. I do not have access to the Windows disks to try to re-install Windows over itself (the computer has a recovery partition but it is unusable); also the drive uses a whole-disk encryption solution and re-installing would be difficult. I absolutely do not want to start from scratch here and install a fresh Windows, reinstall dozens of software packages, try and remember dozens of development-related customizations/etc. Given all that... does anyone have any helpful advice? I need .NET 3.5 - 2.0 working as I am a developer and need to build and test against it. Thanks! Quinxy

  Read the article

• proftpd, dynamic IP, and filezilla: port troubles

  - by Yami

  The basic setup: Two computers, one running proftpd, one attempting to connect via filezilla. Both linux (xubuntu on the server, kubuntu on the client). Both are at the moment behind a router on a residential (read: dynamic IP) connection; the client is a laptop I plan to take away from the home network, so I'll need this to work externally. I have my router set up to allow specific ports forwarded to each machine and, where possible, have plugged in those numbers into proftpd (via gadmin, double-checking the config file) and filezilla. Attempting to connect via active mode using the internal IP works: Status: Connecting to 192.168.1.139:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 192,168,1,52,153,140 Response: 200 PORT command successful Command: LIST Response: 150 Opening ASCII mode data connection for file list Response: 226 Transfer complete Status: Directory listing successful Attempting to connect via the domain name, however, leads to issues; in active mode, the PORT is the last command to be received according to the server's logs, and in passive mode, it's the PASV command. This leads me to believe I'm being redirected to a bad port? Active Sample: Status: Resolving address of <url> Status: Connecting to <ip:port> Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 174,111,127,27,153,139 Response: 200 PORT command successful Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing Passive sample: Status: Resolving address of ftp.bonsaiwebdesigns.com Status: Connecting to 174.111.127.27:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER yamikuronue Response: 331 Password required for yamikuronue Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (64,95,64,197,101,88). Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing In both cases, the log file ends at "PORT" or "PASV" - there's no record of ever receiving a "LIST" command. Just above that I can see the attempt to connect actively via the internal IP, which does indeed include a LIST command. My config file includes "PassivePorts 20001-26999", which are the port forwards I set up for the ftp server, and "Port 8085", which is also forwarded to the same machine. I also have a MasqueradeAddress set up to prevent it from reporting its internal IP, which was an earlier issue I had. I think what I'm asking is, is there another setting someplace I have to change to get this setup to work?

  Read the article

• Scenarios for Bazaar and SVN interaction

  - by Adam Badura

  At our company we are using SVN repository. I'm doing programming from both work (main place) and home (mostly experiments and refactoring). Those are two different machines, in different networks and almost never turned on at the same time (after all I'm either at work or at home...) I wanted to give a chance to some distributed version control system and solve some of the issues associated with SVN based process and having two machines. From git, Mercurial and Bazaar I chose to start with Bazaar since it claims that it is designed do be used by human beings. Its my first time with distributed system and having nice and easy user interface was important for me. Features I wanted to achieve were: Being able to update from SVN repository and commit to it. Being able to commit locally steps of my work on a task. Being able to have few separate tasks at the same time in their own local branches. Being able to share those branches between my work and home computer. As a means of transport between work and home computer I wanted to use a pen-drive. Company server will not work since I may not instal there anything. Neither will work a web service repository as I may not upload source code to web (especially if it would be public which seems to be a common case in free web services). This transport should be Bazaar-based (or what ever else I will end with) so it can be done more or less automatically but manual copying and pasting some folders or generating patch files (providing they would work - I have bad experience with patch files in SVN) would work as well if there is no better solution. Yet the pen-drive should only be used for transportation. I do not want to edit or build there. I tried following Bazaar guidelines for integration with SVN. But I failed. I tried both bzr svn-import and bzr checkout providing URL from my repository as both https://... and svn+https://.... In some cases it had some issues with certificates but the output specified argument to ignore them so I did that. Sometimes it asked me to log in (in other cases maybe it remembered... I don't know) which I did. All were running very slow (this could be our server issue) and at some point were interrupted due to connection interruption (this almost for sure is our server issue: it truncates the connection after some time). But since (as opposed to SVN) restarting starts a new rather than from point where it was interrupted I was unable to reach all the ~19000 revisions (ending usually somewhere around 150). What and how should I do with Bazaar? Is is possible to somehow import SVN repository from the local checkout (so that I do not suffer the connection truncation)? I was told that a colleague that used to work with us has done something similar (importing SVN repository with full history) with Mercurial like in no time. So I'm seriously considering now trying Mercurial even if only to see if that will work. But also what are your general guidelines to achieve the listed features?

  Read the article

• What is wrong in my DKIM setup? I'm getting all fails

  - by djechelon

  I own a domain name I have implemented SPF and DKIM to avoid my mails being junked. I have also upgraded to DMARC in monitor mode. Since I received a few failure reports recently I wanted to investigate more. I have only one server sending outbound emails, running postfix + dkimproxy. I trust that dkimproxy has no major software bugs resulting in bad messages. I have tested ReturnPath's automated DKIM test and this is the part related to DKIM/DomainKeys DKIM Results ============ Result = failed: invalid key for signature: Syntax error in tag: \"v Domain = domain.org Selector = sel DNS Record(s) = sel._domainkey.domain.org TXT "v=1; p=MIICIjANBgkqhkiG9w0BAQEFAAOCAg8AMIICCgKCAgEAsMMLhxzXkU+tagc44oMi7eX2BsFb8BsWeT8MRL+hxi4Lsosx7tuPm90iYgilNteyJoXuSP5SUf8B2tDAifdzYQhfhctr0hX9b6ocBCukGq5p0GHpNsCPWyFvxZsCkGqLRmkfb0c36quEAWBeQLe4Z/BwXBBiW1g96WFNb2/GRI1+9OHhligdfuo4PPuU+xiwX4GB0Ik50cJL4xTdBf7lrFwoGYa03ZkXuzKxeGE4cTk50OeIs6eqrzAfbmej4nCex2qGOUt1TWI7ZvCY7u3Gxj+XKaE7VFrQACZof+NP0k2pXPHg9saGJqZrr2i6+RoxGD0w/ibjAWij9enwqlnv2ORsZfe+FmXNOLJAhlYvhHaruubDpte1c7V3ZKDceM45ZawnVmSdLCfBrMbsqipzy8NXN5MxuANYFBkx5EDT+Ieab+zqcnf08m9bgDc4RXMYppDT1/lUy6On+nyfZEnJWiH3BUtgxS8X0uXciXbsooTmPnpkzzvvKXAE/Tv3XqL90q51geqP0EmaZI6lRTpiqoX7zFGlEBiiF7/u8oheszATks8LsNZ/boTFy0OVldbYNhxlIuRmqeXkqD6+kM5ObKtMEv3AdaeBiZmvyJTP8tCsSmPt+e954RLlz2HaDjjNnZNgsj/39U2RzZsFbVqW6uyQh36/y1X4joOiPf366GkCAwEAAQ==; t=s" Public Key Length = 4096 DomainKeys Results ================== Domain = domain.org Selector = sel DNS Record(s) = sel._domainkey.domain.org TXT "v=1; p=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; t=s" The mail displays an anonymised DNS record with genuine public key. It reports an error in tag v. A few hours ago I noticed my v tag was v=DKIM1 instead of v=1 as specified in RFC. I thought it was an error made by me during the initial setup months ago and fixed to v=1, but anyway I received one DMARC success from Google. Let me explain better: I enforced DMARC a couple of days ago. On 4/16 morning I got a mail from Google telling me that DMARC fully passes, then since 4/17 I get all failures. Then I discovered the v=DKIM1 tag and replaced with v=1 without success I have not modified my DNS records before that. So, keeping in topic with the question, why does ReturnPath refuse my DKIM DNS record? Is something wrong in my DKIM implementation at DNS level? [Add] I have just tried port25.com's tester but at least DKIM passes ---------------------------------------------------------- DomainKeys check details: ---------------------------------------------------------- Result: permerror (DK_STAT_BADKEY: Unusable key, public if verifying, private if signing.) ID(s) verified: header.From=########### DNS record(s): sel._domainkey.domain.org. 1800 IN TXT ""v=1; p=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; t=s"" ---------------------------------------------------------- DKIM check details: ---------------------------------------------------------- Result: pass (matches From: #########) ID(s) verified: header.d=domain.org Canonicalized Headers: message-id:<[email protected]>'0D''0A' date:Thu,'20'18'20'Apr'20'2013'20'11:40:26'20'+0200'0D''0A' from:#############'0D''0A' mime-version:1.0'0D''0A' to:[email protected]'0D''0A' subject:Test'0D''0A' content-type:text/plain;'20'charset=ISO-8859-15;'20'format=flowed'0D''0A' content-transfer-encoding:7bit'0D''0A' dkim-signature:v=1;'20'a=rsa-sha1;'20'c=relaxed;'20'd=domain.org;'20'h='20'message-id:date:from:mime-version:to:subject:content-type'20':content-transfer-encoding;'20's=dom;'20'bh=uoq1oCgLlTqpdDX/iUbLy7J1Wi'20'c=;'20'b= Canonicalized Body: '0D''0A' DNS record(s): sel._domainkey.domain.org. 1800 IN TXT ""v=1; p=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; t=s"" Public key used for verification: sel._domainkey.domain.org (4096 bits)

  Read the article

• Using Upstart to manage Unicorn w/ rbenv + bundler binstubs w/ ruby-local-exec shebang

  - by codykrieger

  Alright, this is melting my brain. It might have something to do with the fact that I don't understand Upstart as well as I should. Sorry in advance for the long question. I'm trying to use Upstart to manage a Rails app's Unicorn master process. Here is my current /etc/init/app.conf: description "app" start on runlevel [2] stop on runlevel [016] console owner # expect daemon script APP_ROOT=/home/deploy/app PATH=/home/deploy/.rbenv/shims:/home/deploy/.rbenv/bin:$PATH $APP_ROOT/bin/unicorn -c $APP_ROOT/config/unicorn.rb -E production # >> /tmp/upstart.log 2>&1 end script # respawn That works just fine - the Unicorns start up great. What's not great is that the PID detected is not of the Unicorn master, it's of an sh process. That in and of itself isn't so bad, either - if I wasn't using the automagical Unicorn zero-downtime deployment strategy. Because shortly after I send -USR2 to my Unicorn master, a new master spawns up, and the old one dies...and so does the sh process. So Upstart thinks my job has died, and I can no longer restart it with restart or stop it with stop if I want. I've played around with the config file, trying to add -D to the Unicorn line (like this: $APP_ROOT/bin/unicorn -c $APP_ROOT/config/unicorn.rb -E production -D) to daemonize Unicorn, and I added the expect daemon line, but that didn't work either. I've tried expect fork as well. Various combinations of all of those things can cause start and stop to hang, and then Upstart gets really confused about the state of the job. Then I have to restart the machine to fix it. I think Upstart is having problems detecting when/if Unicorn is forking because I'm using rbenv + the ruby-local-exec shebang in my $APP_ROOT/bin/unicorn script. Here it is: #!/usr/bin/env ruby-local-exec # # This file was generated by Bundler. # # The application 'unicorn' is installed as part of a gem, and # this file is here to facilitate running it. # require 'pathname' ENV['BUNDLE_GEMFILE'] ||= File.expand_path("../../Gemfile", Pathname.new(__FILE__).realpath) require 'rubygems' require 'bundler/setup' load Gem.bin_path('unicorn', 'unicorn') Additionally, the ruby-local-exec script looks like this: #!/usr/bin/env bash # # `ruby-local-exec` is a drop-in replacement for the standard Ruby # shebang line: # # #!/usr/bin/env ruby-local-exec # # Use it for scripts inside a project with an `.rbenv-version` # file. When you run the scripts, they'll use the project-specified # Ruby version, regardless of what directory they're run from. Useful # for e.g. running project tasks in cron scripts without needing to # `cd` into the project first. set -e export RBENV_DIR="${1%/*}" exec ruby "$@" So there's an exec in there that I'm worried about. It fires up a Ruby process, which fires up Unicorn, which may or may not daemonize itself, which all happens from an sh process in the first place...which makes me seriously doubt the ability of Upstart to track all of this nonsense. Is what I'm trying to do even possible? From what I understand, the expect stanza in Upstart can only be told (via daemon or fork) to expect a maximum of two forks.

  Read the article

• Why can I resolve this hostname but not a cname to this hostname?

  - by Joe Hopfgartner

  if a run dig against a hostname, i get the according cname, however i get an NXDOMAIN error (non existent domain). if i run dig against the cname i got, I can resolve it to an IP address successfully. It is reproduceable. On the system I am currently on it is always the case, on other systems it sometimes works and sometimes not, and on other systems it seems to work all the time. If i run using a nameserver i specify (for example googles public nameserver) i can successfully resolve the hostname. i would just blame the local system, but it seems i am not having the only one problems the 2nd domain (unrestrict.me) is hosted on amazon route 53 nameservers. the 1st one on another dns server which has proofen to be fully functional and reliable over the years. i once switchted with the other domain to amazon dns as well, everything seemed to work, also various dns health check tests reported fine, however i recieved a lot of support tickets that dns resolution would not work. is amazon just "bad" or am i doing something wrong? i did not tamper with the domain in any way on the local system (in case of caching or making a custom dns view or whatever...) joe@joe:~$ dig scorpion.premiumize.me ; <<>> DiG 9.8.1-P1 <<>> scorpion.premiumize.me ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NXDOMAIN, id: 10222 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;scorpion.premiumize.me. IN A ;; ANSWER SECTION: scorpion.premiumize.me. 180 IN CNAME alpha.nue.scorpion.unrestrict.me. ;; Query time: 28 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Mon Jun 18 10:28:39 2012 ;; MSG SIZE rcvd: 84 joe@joe:~$ dig alpha.nue.scorpion.unrestrict.me ; <<>> DiG 9.8.1-P1 <<>> alpha.nue.scorpion.unrestrict.me ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 25381 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;alpha.nue.scorpion.unrestrict.me. IN A ;; ANSWER SECTION: alpha.nue.scorpion.unrestrict.me. 300 IN A 78.46.25.130 ;; Query time: 48 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Mon Jun 18 10:28:47 2012 ;; MSG SIZE rcvd: 66 joe@joe:~$

  Read the article

• How should I ask for help in getting my emails to stop bouncing?

  - by Gregg Williams

  For several months, people have been telling me that emails they sent to me have been bouncing back, marked as undeliverable. The bounce message would contain portions like this: Final-Recipient: rfc822;[email protected] Action: failed Status: 5.7.1 Diagnostic-Code: smtp;550 5.7.1 <[email protected]>... Recipient declines email from 69.64.159.2, <spamhaus-xbl>, Ref: http://www.spamhaus.org/query/bl?ip=69.64.159.2 Clicking the link on the last line, the destination page told me that "this IP address is infected with/emitting spamware/spamtrojan traffic and needs to be fixed." I could temporarily de-list this node by clicking a link on that page, but it would get back on the list and more emails to me to bounce. I own a domain, innerpaths.net, and I normally use [email protected] for my email. I have my domain registrar, namecheap.com, forward all email from innerpaths.net to the email account [email protected]. (BTW, I had this same problem at a former registrar. I changed registrars, hoping that would fix the problem. It didn't.) Trying to isolate the problem, I asked namecheap.com what I should do. Their answer, though substantial, left me scratching my head: We have received feedback from our upstream provider which informed us that the mail server that you are trying to email subscribes to a 3rd party blacklist service which they appear to be listed on at the present time and is causing destination mail server to reject the messages. Being blocked with one of these services can happen to anyone for many reasons and is something that is beyond our control. 3rd party blacklist services require companies whose mail servers they have blacklisted, pay fees in order to be removed from their lists. As we cannot pay fees to blacklist services which require them for removal, you should contact your email provider and have them whitelist our mail server IP address: 69.64.157.73. My best guess is that I should email my ISP, sonic.net, tell them what is going on and ask them to whitelist the IP address 69.64.157.73. (If not, please let me know.) But I want to know what is going on and how email works. I understand that there's a device at location 69.64.159.2 that is doing something bad that causes the "destination mail server [sonic.net's, I assume --gw] to reject the messages." I know that email is sent through multiple devices in a way that eventually gets it to its destination. Beyond that, here are my questions: 1) I thought the Internet "routed around damage." Why does email starting at namecheap.com always (or is it 'sometimes'?) go through 69.64.159.2? 2) Who is the "upstream provider" that the namecheap.com representative mentions, and what is their role? 3) How does having sonic.net's whitelisting namecheap.com's mail server prevent my email being bounced by 69.64.159.2? I've searched the Internet for answers but have found nothing useful. Thanks for whatever answers you can provide.

  Read the article

• Apache mod_jk Setting for Tomcat - workers.properties

  - by sissonb

  I am trying to direct files with .jsp extensions to tomcat. Otherwise I want apache to serve the file directly (no tomcat). Currently I have a test.jsp which is supposed to create an HTML page with the current date in the body. Instead when I go to that .jsp I see the JK Status Manager. The mod_jk.logs only show, init_jk::mod_jk.c (3365): mod_jk/1.2.35 initialized. I have tomcat and apache setup on my server. Apache runs on 80 and tomcat runs on 8080. localhost:8080 show the tomcat welcome page. I downloaded tomcat-connectors-1.2.35-windows-i386-httpd-2.2.x and copied the mod_jk.so to C:\apache\modules. Then I added LoadModule jk_module modules/mod_jk.so to my httpd.conf. I restart apache and the module loads just fine. Next I downloaded the mod_jk source to get the workers.properties file. I copy workers.properties to C:\apache\confg. Then I added this user, workers.tomcat_home="C:/Program Files/Apache Software Foundation/Tomcat 7.0" workers.java_home="C:/Program Files/Java/jdk1.7.0_03" worker.list=ajp13 worker.ajp13.port=8080 worker.ajp13.host=localhost worker.ajp13.type=ajp13 worker.ajp13.socket_timeout=10 When I try to use the ajp13 user in my httpd.conf I get the following error in my mod_jk.log, [Wed Mar 28 13:08:51 2012] [2196:4100] [info] ajp_connection_tcp_get_message::jk_ajp_common.c (1258): (ajp13) can't receive the response header message from tomcat, network problems or tomcat (127.0.0.1:8080) is down (errno=60) [Wed Mar 28 13:08:51 2012] [2196:4100] [error] ajp_get_reply::jk_ajp_common.c (2117): (ajp13) Tomcat is down or refused connection. No response has been sent to the client (yet) [Wed Mar 28 13:08:51 2012] [2196:4100] [info] ajp_service::jk_ajp_common.c (2614): (ajp13) sending request to tomcat failed (recoverable), (attempt=1) Next I update my httpd.conf with, JkWorkersFile C:/apache/conf/workers.properties JkLogFile C:/apache/logs/mod_jk.log JkLogLevel info JkLogStampFormat "[%a %b %d %H:%M:%S %Y] " Also I added JkMount /*.jsp jk-status to my virtual host like this, <VirtualHost 192.168.5.250:80> JkMount /*.jsp jk-status #JkMount /*.jsp ajp13 ServerName bgsisson.com ServerAlias www.bgsisson.com DocumentRoot C:/www/resume </VirtualHost> I think i need to include a uriworkermap.properties file, but this is where I am getting stuck. I have put up a test .jsp at bgsisson.com/test.jsp It shows the JK Status Manager when I use JkMount /*.jsp jk-status and 502 Bad Gateway when I use JkMount /*.jsp ajp13 test.jsp <%-- use the 'taglib' directive to make the JSTL 1.0 core tags available; use the uri "http://java.sun.com/jsp/jstl/core" for JSTL 1.1 --%> <%@ taglib uri="http://java.sun.com/jstl/core" prefix="c" %> <%-- use the 'jsp:useBean' standard action to create the Date object; the object is set as an attribute in page scope --%> <jsp:useBean id="date" class="java.util.Date" /> <html> <head><title>First JSP</title></head> <body> <h2>Here is today's date</h2> <c:out value="${date}" /> </body> </html>

  Read the article

• What Apache/PHP configurations do you know and how good are they?

  - by FractalizeR

  Hello. I wanted to ask you about PHP/Apache configuration methods you know, their pros and cons. I will start myself: ---------------- PHP as Apache module---------------- Pros: good speed since you don't need to start exe every time especially in mpm-worker mode. You can also use various PHP accelerators in this mode like APC or eAccelerator. Cons: if you are running apache in mpm-worker mode, you may face stability issues because every glitch in any php script will lead to unstability to the whole thread pool of that apache process. Also in this mode all scripts are executed on behalf of apache user. This is bad for security. mpm-worker configuration requires PHP compiled in thread-safe mode. At least CentOS and RedHat default repositories doesn't have thread-safe PHP version so on these OSes you need to compile at least PHP yourself (there is a way to activate worker mpm on Apache). The use of thread-safe PHP binaries is considered experimental and unstable. Plus, many PHP extensions does not support thread-safe mode or were not well-tested in thread-safe mode. ---------------- PHP as CGI ---------------- This seems to be the slowest default configuration which seems to be a "con" itself ;) ---------------- PHP as CGI via mod_suphp ---------------- Pros: suphp allows you to execute php scipts on behalf of the script file owner. This way you can securely separate different sites on the same machine. Also, suphp allows to use different php.ini files per virtual host. Cons: PHP in CGI mode means less performance. In this mode you can't use php accelerators like APC because each time new process is spawned to handle script rendering the cache of previous process useless. BTW, do you know the way to apply some accelerator in this config? I heard something about using shm for php bytecode cache. Also, you cannot configure PHP via .htaccess files in this mode. You will need to install PECL htscanner for this if you need to set various per-script options via .htaccess (php_value / php_flag directives) ---------------- PHP as CGI via suexec ---------------- This configuration looks the same as with suphp, but I heard, that it's slower and less safe. Almost same pros and cons apply. ---------------- PHP as FastCGI ---------------- Pros: FastCGI standard allows single php process to handle several scripts before php process is killed. This way you gain performance since no need to spin up new php process for each script. You can also use PHP accelerators in this configuration (see cons section for comment). Also, FCGI almost like suphp also allows php processes to be executed on behalf of some user. mod_fcgid seems to have the most complete fcgi support and flexibility for apache. Cons: The use of php accelerator in fastcgi mode will lead to high memory consumption because each PHP process will have his own bytecode cache (unless there is some accelerator that can use shared memory for bytecode cache. Is there such?). FastCGI is also a little bit complex to configure. You need to create various configuration files and make some configuration modifications. It seems, that fastcgi is the most stable, secure, fast and flexible PHP configuration, however, a bit difficult to be configured. But, may be, I missed something? Comments are welcome!

  Read the article

• SSH-forwarded X11 display from Linux to Mac lost after some time

  - by mklein9

  I have a new and vexing problem with ssh forwarding my X11 connection when logging in from a Mac (10.7.2) to Linux (Ubuntu 8.04). I have no trouble using ssh -X to log in to the remote machine and starting an X11-based application from that shell. What has recently started happening is that additional invocations of X11 applications from that same shell, after a while (on the order of hours), are unable to start because the forwarded display is being blocked (I presume). When attempting to start xterm, for example, I get the usual message about a bad DISPLAY setting, such as: xterm Xt error: Can't open display: localhost:10.0 But the X11 application I started right when I logged in is still running along just fine, using that exact same display (localhost:10.0), just that it was started earlier. I turned on verbose logging in sshd_config and I see this in the /var/log/auth.log file in response to the failed xterm startup attempt: sshd[22104]: channel 8: open failed: administratively prohibited: open failed If I ssh -X to the server again, starting a new shell and getting assigned a new display (localhost:11.0), the same process repeats: the X11 applications started early on run just fine for as long as I keep them open (days), but after a few hours I cannot start any new ones from that shell. Particulars: OpenSSH sshd server running on Ubuntu 8.04, display forwarded to a Mac running Lion (10.7.2) with the default Apple X server. The systems are connected on an Ethernet LAN with a single switch between them. Neither machine is running a firewall. Until recently (a few days ago) this setup worked perfectly so I am mystified as to where to look next. I am by no means an X11 or SSH expert but have good UNIX/Linux experience. Nothing obvious has changed in either client or server configuration although I have tried changing a few options to try to debug this, like setting sshd_config's TCPKeepAlive to no, and setting "host +localhost" (you can tell I've been Googling). When logging in from a Linux 11.10 laptop to the same remote host over the same network and switch, this problem does not occur -- an xterm can be invoked successfully hours later from the same ssh login shell while the same experiment from the Mac fails (tested this morning to be sure), so it would appear to be a Mac-specific issue. With "LogLevel DEBUG3" set on the remote machine (sshd server), and no change made in the client connections by me, /var/log/auth.log shows one slight change in connection status reports overnight, which is the port number used by the one successful ssh session from the Linux machine (I think), connection #7 below: sshd[20173]: debug3: channel 7: status: The following connections are open:\r\n #0 server-session (t4 r0 i0/0 o0/0 fd 14/13 cfd -1)\r\n #3 X11 connection from 127.0.0.1 port 57564 (t4 r1 i0/0 o0/0 fd 16/16 cfd -1)\r\n #4 X11 connection from 127.0.0.1 port 57565 (t4 r2 i0/0 o0/0 fd 17/17 cfd -1)\r\n #5 X11 connection from 127.0.0.1 port 57566 (t4 r3 i0/0 o0/0 fd 18/18 cfd -1)\r\n #6 X11 connection from 127.0.0.1 port 57567 (t4 r4 i0/0 o0/0 fd 19/19 cfd -1)\r\n #7 X11 connection from 127.0.0.1 port 59007 In this report, everything is the same between status reports except the port number used by connection #7 which I believe is the Linux client -- the only one still maintaining a display connection. It continues to increment over time, judging by a sequence of these reports overnight. Thanks for any help, -Mike

  Read the article

• GNU/Linux swapping blocks system

  - by Ole Tange

  I have used GNU/Linux on systems from 4 MB RAM to 512 GB RAM. When they start swapping, most of the time you can still log in and kill off the offending process - you just have to be 100-1000 times more patient. On my new 32 GB system that has changed: It blocks when it starts swapping. Sometimes with full disk activity but other times with no disk activity. To examine what might be the issue I have written this program. The idea is: 1 grab 3% of the memory free right now 2 if that caused swap to increase: stop 3 keep the chunk used for 30 seconds by forking off 4 goto 1 - #!/usr/bin/perl sub freekb { my $free = `free|grep buffers/cache`; my @a=split / +/,$free; return $a[3]; } sub swapkb { my $swap = `free|grep Swap:`; my @a=split / +/,$swap; return $a[2]; } my $swap = swapkb(); my $lastswap = $swap; my $free; while($lastswap >= $swap) { print "$swap $free"; $lastswap = $swap; $swap = swapkb(); $free = freekb(); my $used_mem = "x"x(1024 * $free * 0.03); if(not fork()) { sleep 30; exit(); } } print "Swap increased $swap $lastswap\n"; Running the program forever ought to keep the system at the limit of swapping, but only grabbing a minimal amount of swap and do that very slowly (i.e. a few MB at a time at most). If I run: forever free | stdbuf -o0 timestamp > freelog I ought to see swap slowly rising every second. (forever and timestamp from https://github.com/ole-tange/tangetools). But that is not the behaviour I see: I see swap increasing in jumps and that the system is completely blocked during these jumps. Here the system is blocked for 30 seconds with the swap usage increases with 1 GB: secs 169.527 Swap: 18440184 154184 18286000 170.531 Swap: 18440184 154184 18286000 200.630 Swap: 18440184 1134240 17305944 210.259 Swap: 18440184 1076228 17363956 Blocked: 21 secs. Swap increase 2400 MB: 307.773 Swap: 18440184 581324 17858860 308.799 Swap: 18440184 597676 17842508 330.103 Swap: 18440184 2503020 15937164 331.106 Swap: 18440184 2502936 15937248 Blocked: 20 secs. Swap increase 2200 MB: 751.283 Swap: 18440184 885288 17554896 752.286 Swap: 18440184 911676 17528508 772.331 Swap: 18440184 3193532 15246652 773.333 Swap: 18440184 1404540 17035644 Blocked: 37 secs. Swap increase 2400 MB: 904.068 Swap: 18440184 613108 17827076 905.072 Swap: 18440184 610368 17829816 942.424 Swap: 18440184 3014668 15425516 942.610 Swap: 18440184 2073580 16366604 This is bad enough, but what is even worse is that the system sometimes stops responding at all - even if I wait for hours. I have the feeling it is related to the swapping issue, but I cannot tell for sure. My first idea was to tweak /proc/sys/vm/swappiness from 60 to 0 or 100, just to see if that had any effect at all. 0 did not have an effect, but 100 did cause the problem to arise less often. How can I prevent the system from blocking for such a long time? Why does it decide to swapout 1-3 GB when less than 10 MB would suffice?

  Read the article

• BSOD & System Failure after trying to install a new RAM

  - by Praveen Kumar

  I have updated the question with sections, so that people won't find it difficult to read. Basic System Information Let me give a basic introduction on my system. I have a system of following configuration: Processor: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz 3.40GHz RAM: Corsair Vengeance - 4GB Single Module DDR3 Memory Kit (CMZ4GX3M1A1600C9) x 2 OS: Windows 7 Ultimate, SP1 Build 7601 HDD: 1 TB Seagate 7200 RPM The Problem It was working fine for about an year. Yesterday I planned to increase my RAM to 16 GB by putting another set of two Corsair Vengeance - 4GB Single Module DDR3 Memory Kit (CMZ4GX3M1A1600C9). I got it from an authorized reseller and also, the RAM was fitted by a service engineer only. After the RAM was fit (all the four), the system failed to start, with an error code of 0x000000f4. The complete information of it is: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.1 Locale ID: 16393 Additional information about the problem: BCCode: f4 BCP1: 0000000000000003 BCP2: FFFFFA8008A39060 BCP3: FFFFFA8008A39340 BCP4: FFFFF800037C8510 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\093012-13041-01.dmp C:\Users\Praveen Kumar\AppData\Local\Temp\WER-30716-0.sysdata.xml Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt Another Problem We first thought that it was the RAM, which caused the issue. So I returned the RAMs and now my computer configuration is exactly how it was the previous day. But, following the removal of the RAM, I also had several crashes after that. One suspicious thing was with an error code c0000134: STOP: c0000135 The program can’t start because %hs is missing from your computer . Try resintalling the program to fix this problem. After reading contents from this, this and this, which were never my case, they didn't help me. But I didn't receive any more STOP c0000134 messages. But this 0x000000f4 keeps on coming. I am writing from the same system and it allows me to work for say, half an hour max. Then I hear a device disconnect sound, the one you hear in Windows 7, when a USB Mass Storage Device is plugged out. Immediately following that, my screen goes blank and I get 0x000000f4 blue screen. Okay, now I am really concerned about my Hard Disk data, but I have no clue if there is a problem with the HDD. My Question What all files do I need to submit for your reference? Can this issue be fixed? I am getting more time if I remove my RAM, clean it and then put it back. Weird! Hope I have given the necessary information to help you guys. Thanks in advance. Minidumps I have uploaded all the Minidump DMP files from C:\Windows\Minidump folder here: http://www.praveen-kumar.com/Minidumps.zip Let me know if you face any issues in accessing it. Will be able to share elsewhere. Updates 30-Sep-2012 10:15 AM IST: When I keep the system cover opened, pressed the HDD Cable well, it is allowing me to be on for about half an hour, I guess? Also, I feel that the CPU fan speed is kind of slow. It rotates at around 900 RPM, but the CPU Temperature is not more than 70° C. 30-Sep-2012 10:30 AM IST: My Modem (Beetel 220BX ADSL2+ Router) failed. I have no idea how it is related to this issue, but I thought that I need to document this too. I really have a bad day here. 30-Sep-2012 11:00 AM IST: System still running fine, with the cabinet cover open, now for about an hour. 30-Sep-2012 12:00 PM IST: I shut down the system and closed the cabinet. Started the system, and it hung after giving the password. After a few minutes, got the same 0x000000f4 error. So, while it is in the upright position, fixed the Hard Disk cable and now it is booting fine. Waiting for more observations and answers.

  Read the article

• Deploying play! 2.0 application on an apache server with a reverse proxy

  - by locrizak

  I'm trying to deploy my play! 2.0 application on an Ubuntu 11.10 server and I have been running into error after error and hope someone can help me here. I am try to deploy my Play! application using a reverse proxy on Apache 2. I have enabled the apache proxy modules and configured the proxy.conf file in mods_enabled. The vhost for my domain looks like this: <Directory /var/www/stage.domain.com AllowOverride None Order Deny,Allow Deny from all </Directory <VirtualHost *:80 DocumentRoot /var/www/stage.domain.com/web ServerName stage.domain.com ServerAdmin [email protected] # ProxyRequests Off # ProxyPreserveHost On <Proxy * Order allow,deny Allow from all </Proxy # ProxyVia On # ProxyPass /play/ http://localhost:9000/ # ProxyPassReverse /play/ http://localhost:9000/ ErrorLog /var/log/ispconfig/httpd/stage.domain.com/error.log ErrorDocument 400 /error/400.html ErrorDocument 401 /error/401.html ErrorDocument 403 /error/403.html ErrorDocument 404 /error/404.html ErrorDocument 405 /error/405.html ErrorDocument 500 /error/500.html ErrorDocument 502 /error/502.html ErrorDocument 503 /error/503.html <IfModule mod_ssl.c </IfModule <Directory /var/www/stage.domain.com/web Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory <Directory /var/www/clients/client2/web7/web Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory # Clear PHP settings of this website <FilesMatch "\.ph(p3?|tml)$" SetHandler None </FilesMatch # mod_php enabled AddType application/x-httpd-php .php .php3 .php4 .php5 php_admin_value sendmail_path "/usr/sbin/sendmail -t -i [email protected]" php_admin_value upload_tmp_dir /var/www/clients/client2/web7/tmp php_admin_value session.save_path /var/www/clients/client2/web7/tmp # PHPIniDir /var/www/conf/web7 php_admin_value open_basedir /var/www/clients/client2/web7/:/var/www/clients/client2/web7/web:/va$ # add support for apache mpm_itk <IfModule mpm_itk_module AssignUserId web7 client2 </IfModule <IfModule mod_dav_fs.c # Do not execute PHP files in webdav directory <Directory /var/www/clients/client2/web7/webdav <FilesMatch "\.ph(p3?|tml)$" SetHandler None </FilesMatch </Directory # DO NOT REMOVE THE COMMENTS! # IF YOU REMOVE THEM, WEBDAV WILL NOT WORK ANYMORE! # WEBDAV BEGIN # WEBDAV END </IfModule # <Location /play/ # ProxyPass http://localhost:9000/ # SetEnv force-proxy-request-1.0 1 # SetEnv proxy-nokeepalive 1 # </Location ProxyRequests Off ProxyPass /play/ http://localhost:9000/ ProxyPassReverse /play/ localhost:9000/ ProxyPass /play http://localhost:9000/ ProxyPassReverse /play http://localhost:9000/ # SetEnv force-proxy-request-1.0 1 # SetEnv proxy-nokeepalive 1 </VirtualHost This vhost file was generated by ispconfig and I have not touched anything that was there before just added onto. As you can see by the commented out parts I have tried a lot of different things based on random tutorials I have found but all of them have ended up in Internal Server Error, 503 and most often a '502 Bad Gateway`. I can start play and it does connect successfully to my database. I can get a page to show up when there is an error and the play! stack trace error pages comes up but where everything is fine I get one of the errors above. My application.conf file looks like this: db info ....... application.mode=PROD logger.root=ERROR # Logger used by the framework: logger.play=INFO # Logger provided to your application: logger.application=DEBUG http.path="/play/" XForwardedSupport="127.0.0.1" And my hosts file looks like this (I have never changed or added anything to the host file): 127.0.0.1 localhost 127.0.1.1 matrix # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters Any insights onto what I might be doing wrong or if theres anything I can try please let me know! Thanks!! Edit Again the reverse proxy will work (I checked with sending to to google.com). Its when there is a successful connection to Netty. It's like Netty refuses the connection to the page. Edit 2 output from apachectl -S _default_:8081 127.0.0.1 (/etc/apache2/sites-enabled/000-apps.vhost:10) *:8090 is a NameVirtualHost default server 127.0.0.1 (/etc/apache2/sites-enabled/000-ispconfig.vhost:10) port 8090 namevhost 127.0.0.1 (/etc/apache2/sites-enabled/000-ispconfig.vhost:10) *:80 is a NameVirtualHost default server 127.0.0.1 (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost 127.0.0.1 (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost domain.com (/etc/apache2/sites-enabled/100-domain.com.vhost:7) port 80 namevhost domain.com (/etc/apache2/sites-enabled/100-domain.com.vhost:7) port 80 namevhost domain.com (/etc/apache2/sites-enabled/100-domain.com.vhost:7) port 80 namevhost domain.com (/etc/apache2/sites-enabled/100-domain.com.vhost:7) port 80 namevhost domain.com (/etc/apache2/sites-enabled/100-domain.com.vhost:7) port 80 namevhost stage.domain.com (/etc/apache2/sites-enabled/100-stage.domain.com.vhost:7) port 80 namevhost domain.com (/etc/apache2/sites-enabled/100-domain.com.vhost:7)

  Read the article

• Remote Desktop failed logon event 4625 not logging correctly on 2008 Terminal Services server

  - by Zone12

  When I use the new remote desktop with ssl and try to log on with bad credentials it logs a 4625 event as expected. The problem is, it doesn't log the ip address, so I can't block malicious logons in our firewall. The event looks like this: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Microsoft-Windows-Security-Auditing" Guid="{00000000-0000-0000-0000-000000000000}" /> <EventID>4625</EventID> <Version>0</Version> <Level>0</Level> <Task>12544</Task> <Opcode>0</Opcode> <Keywords>0x8010000000000000</Keywords> <TimeCreated SystemTime="2012-04-13T06:52:36.499113600Z" /> <EventRecordID>467553</EventRecordID> <Correlation /> <Execution ProcessID="544" ThreadID="596" /> <Channel>Security</Channel> <Computer>ontheinternet</Computer> <Security /> </System> <EventData> <Data Name="SubjectUserSid">S-1-0-0</Data> <Data Name="SubjectUserName">-</Data> <Data Name="SubjectDomainName">-</Data> <Data Name="SubjectLogonId">0x0</Data> <Data Name="TargetUserSid">S-1-0-0</Data> <Data Name="TargetUserName">notauser</Data> <Data Name="TargetDomainName">MYSERVER-PC</Data> <Data Name="Status">0xc000006d</Data> <Data Name="FailureReason">%%2313</Data> <Data Name="SubStatus">0xc0000064</Data> <Data Name="LogonType">3</Data> <Data Name="LogonProcessName">NtLmSsp</Data> <Data Name="AuthenticationPackageName">NTLM</Data> <Data Name="WorkstationName">MYSERVER-PC</Data> <Data Name="TransmittedServices">-</Data> <Data Name="LmPackageName">-</Data> <Data Name="KeyLength">0</Data> <Data Name="ProcessId">0x0</Data> <Data Name="ProcessName">-</Data> <Data Name="IpAddress">-</Data> <Data Name="IpPort">-</Data> </EventData> </Event> It seems because the logon type is 3 and not 10 like the old rdp sessions, the ip address and other information is not stored. The machine I am trying to connect from is on the internet and not on the same network as the server. Does anyone know where this information is stored (and what other events are generated with a failed logon)? Any help will be much appreciated.

  Read the article

< Previous Page | 364 365 366 367 368 369 370 371 372 373 374 375  | Next Page >