Search Results

Search found 14483 results on 580 pages for 'major mode'.

Page 37/580 | < Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >

• Interactive mode of PSExec not working for console application

  - by Focker

  I am trying to use PSExec to kick off a console application on a remote computer in an interactive state. When I run something like this: PsExec.exe -s -d -i 1 \\MyServer notepad.exe It launches Notepad just fine. If I then run this: PsExec.exe -s -d -i 1 \\MyServer C:\Temp\MyConsoleApp.exe It launches the command windows but doesn't do anything as far as I can tell. As in, when I run my console application locally, it displays a "heartbeat" every 5 seconds, but when I run it remotely, nothing is displayed in the command window. The .exe does show up as a process in Task Manager. Any ideas?

  Read the article

• Windows 7 does not 'wake up' from Sleep mode

  - by the watchmaker

  I'm new to Windows 7, so I don't know if this is normal. When the computer is idle for 30 minutes, the screen goes black and no key pressing or mouse movement will bring the computer out of standby. The computer is still running (fans and hard drive noise) but it will not respond and the screen remains black. The only way to get a response is to press and hold the power button until it goes off, then switch it back on. When it turns on it says "Resuming Windows" and then goes black again. Is this normal? Can the time-out delay be increased? Is there a better workaround than switching the PC on and off?

  Read the article

• Ubuntu Studio 10.4 boots to terminal mode only

  - by Don

  I did clean install from ISO DVD. It boots only to command line asking for login. After I login I enter STARTX and desktop appears and some of the studd actually works, but there are a lot of problems: there is no way to reboot or shut down except to stopx/logoff and enter shutdown sound system doesn't respond pulse audio volume control gives "connection failed, connection refused" DVD drives not available GDebi Package installer is grayed out and so I can't use it (but synaptic package manager works OK) Software Center won't start when clicked -- it just stops trying DBus cant run because it says /usr/local/var/run/dbus/system_bus_socket file not found (also /var/run/dbus/system_bus_socket file not found) There's just a lot of things wrong and I can't help but think something is missing or was mis-coded in the distro so that there are typos in some script somewhere. If anyone can tell me where to begin to untangle this mess I'd appreciate it, but I think it all begins when it can't start the GUI automatically and I need to enter STARTX.

  Read the article

• putty ssh client become not responding frequently in windows 7

  - by Sankaran

  with celeron processor and 512 MB ram windows 7 takes too much time even to open a folder in windows explorer. I connect to internet with GPRS modem. When I tried to connect with remote linux machine with putty ssh client. The problem is the putty becomes Not responding in 2 or 3 minutes. I've to connect again and putty goes Not responding again. When i tried in Safe mode with networking, GPRS modem is not even detected. the modem is USB data card. Is it possible load USB drive in safe mode of windows 7 or any other possibility to connect with remote machine via ssh

  Read the article

• invoke zsh, having it run a command, and then enter interactive mode instead of exiting

  - by Autoplectic

  i'd like to start zsh similar to zsh -c 'my_prog option1 option2' but instead of exiting after running that command, leaving me at the propt of the invoked zsh (not wherever it is being called from). one particular use-case for this is in screenrc files, you could do something like: screen -t my_prog 0 zsh -c 'my_prog opt1 opt2' and after running that command you're left with a shell there instead of it closing.

  Read the article

• How can one one-handed ease working in Emacs?

  - by N.N.

  My right hand is temporarily immobilized. I would like to do some minor work in Emacs, mostly in Org-mode, but also some in AUCTeX. Is there some way to ease one-handed work in Emacs such as some mode or particular work flow? For instance I noticed pressing C-x u is easier than C-_ for undoing and that it is easier to mark text with methods involving C-Space than with combinations of S- and movement commands. I have found http://stackoverflow.com/questions/2391805/how-can-i-remain-productive-with-one-hand-completely-immobilized but that is not what I am asking for. I want to ease whatever little time spent one-handed in Emacs and this is also interesting for situations where there is no injury involved, such as when one hand is occupied. I also do realize I should avoid unnecessary strain.

  Read the article

• Windows 7 - all usb devices go to sleep im idle mode

  - by dvdx

  A strange thing happened after a few updates to the system: Intel rapid storage SSD firmware update Intel Ethernet adapter update GPU Intel update When the computer turns off the screen (after 5 min), an unknown time later, all the USB devices stop working. Sound card Mouse Keybord etc. I can't turn them back on, so I can't wake up the screen or do anything except turn the computer off and back on. I checked my power save profile and all is OK there. I changed in the Device Manager, the Allow USB to sleep in all the hubs. How can I fix this??

  Read the article

• Sporadic EXC_BAD_INSTRUCTION (SIGILL) when in 64 bit mode

  - by Ger Teunis

  For some reason for a low-number of users (say 1 in a few hundred) the application seem to crash when run in 64bit mode on a Snow Leopard 10.6.3 I've attached the code, but please remind IT IS NOT A CODE issue. The crashed seem to be random in com.apple.AppKit at random locations and random moments. Anyone else had any experiences? Using GCC compiler of Xcode 3.2.2 Crash #1 of user Code Type: X86-64 (Native) Parent Process: launchd [90] Date/Time: 2010-05-02 04:12:59.708 -0500 OS Version: Mac OS X 10.6.3 (10D573) Report Version: 6 Exception Type: EXC_BAD_INSTRUCTION (SIGILL) Exception Codes: 0x0000000000000001, 0x0000000000000000 Crashed Thread: 0 Dispatch queue: com.apple.main-thread Application Specific Information: objc[232]: alt handlers in objc runtime are buggy! Thread 0 Crashed: Dispatch queue: com.apple.main-thread 0 libobjc.A.dylib 0x00007fff874dd8b7 _objc_fatal + 238 1 libobjc.A.dylib 0x00007fff874de57c objc_addExceptionHandler + 1026 2 com.apple.CoreFoundation 0x00007fff83914212 _CFDoExceptionOperation + 402 3 com.apple.AppKit 0x00007fff87afc55d _NSAppKitLock + 79 4 com.apple.AppKit 0x00007fff87bd1f93 +[NSColorList _findColorListNamed:forDeviceType:] + 86 5 com.apple.AppKit 0x00007fff87b9d304 -[NSCatalogColor colorUsingColorSpaceName:device:] + 255 6 com.apple.AppKit 0x00007fff87c985ad -[NSLayoutManager(NSPrivate) _drawGlyphsForGlyphRange:atPoint:parameters:] + 4764 7 com.apple.AppKit 0x00007fff87c5d79c -[NSTextView drawRect:] + 1839 8 com.apple.AppKit 0x00007fff87c5ce2e -[NSTextView _drawRect:clip:] + 2343 9 com.apple.AppKit 0x00007fff87be4485 -[NSView _recursiveDisplayAllDirtyWithLockFocus:visRect:] + 1325 10 com.apple.AppKit 0x00007fff87be47ef -[NSView _recursiveDisplayAllDirtyWithLockFocus:visRect:] + 2199 11 com.apple.AppKit 0x00007fff87be2b57 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 767 12 com.apple.AppKit 0x00007fff87be3a23 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 4555 13 com.apple.AppKit 0x00007fff87be3a23 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 4555 14 com.apple.AppKit 0x00007fff87be3a23 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 4555 15 com.apple.AppKit 0x00007fff87be3a23 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 4555 16 com.apple.AppKit 0x00007fff87be3a23 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 4555 17 com.apple.AppKit 0x00007fff87be3a23 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 4555 18 com.apple.AppKit 0x00007fff87be3a23 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 4555 19 com.apple.AppKit 0x00007fff87be3a23 -[NSView _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 4555 20 com.apple.AppKit 0x00007fff87be2678 -[NSThemeFrame _recursiveDisplayRectIfNeededIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:topView:] + 254 21 com.apple.AppKit 0x00007fff87bdef27 -[NSView _displayRectIgnoringOpacity:isVisibleRect:rectIsVisibleRectForView:] + 2683 22 com.apple.AppKit 0x00007fff87b58777 -[NSView displayIfNeeded] + 969 23 com.apple.AppKit 0x00007fff87b53622 _handleWindowNeedsDisplay + 678 24 com.apple.Foundation 0x00007fff8600fa4d __NSFireTimer + 114 25 com.apple.CoreFoundation 0x00007fff83908708 __CFRunLoopRun + 6488 26 com.apple.CoreFoundation 0x00007fff839068df CFRunLoopRunSpecific + 575 27 com.apple.HIToolbox 0x00007fff821b5ada RunCurrentEventLoopInMode + 333 28 com.apple.HIToolbox 0x00007fff821b58df ReceiveNextEventCommon + 310 29 com.apple.HIToolbox 0x00007fff821b5798 BlockUntilNextEventMatchingListInMode + 59 30 com.apple.AppKit 0x00007fff87b28a2a _DPSNextEvent + 708 31 com.apple.AppKit 0x00007fff87b28379 -[NSApplication nextEventMatchingMask:untilDate:inMode:dequeue:] + 155 32 com.apple.AppKit 0x00007fff87d37060 -[NSTextView mouseDown:] + 8426 33 com.apple.AppKit 0x00007fff87c21f1b -[NSWindow sendEvent:] + 5409 34 com.apple.AppKit 0x00007fff87b57662 -[NSApplication sendEvent:] + 4719 35 com.apple.AppKit 0x00007fff87aee0aa -[NSApplication run] + 474 36 com.apple.AppKit 0x00007fff87ae6d7c NSApplicationMain + 364 37 com.NZBVortex.NZBVortex 0x0000000100000fe0 start + 52 Crash #2 from same user moments later Code Type: X86-64 (Native) Parent Process: launchd [76] Date/Time: 2010-05-02 11:59:33.226 +0200 OS Version: Mac OS X 10.6.3 (10D573) Report Version: 6 Exception Type: EXC_BAD_INSTRUCTION (SIGILL) Exception Codes: 0x0000000000000001, 0x0000000000000000 Crashed Thread: 0 Dispatch queue: com.apple.main-thread Application Specific Information: objc[4360]: alt handlers in objc runtime are buggy! Thread 0 Crashed: Dispatch queue: com.apple.main-thread 0 libobjc.A.dylib 0x00007fff8015d8b7 _objc_fatal + 238 1 libobjc.A.dylib 0x00007fff8015e57c objc_addExceptionHandler + 1026 2 com.apple.CoreFoundation 0x00007fff85367212 _CFDoExceptionOperation + 402 3 com.apple.AppKit 0x00007fff840b5f2f -[NSViewHierarchyLock lockForReadingWithExceptionHandler:] + 478 4 com.apple.AppKit 0x00007fff8420753e -[NSConcreteTextStorage _lockForReading] + 243 5 com.apple.AppKit 0x00007fff841e1449 -[NSLayoutManager(NSPrivate) _fillGlyphHoleForCharacterRange:startGlyphIndex:desiredNumberOfCharacters:] + 320 6 com.apple.AppKit 0x00007fff840e204a _NSFastFillAllGlyphHolesForGlyphRange + 719 7 com.apple.AppKit 0x00007fff841e10e2 _NSFastFillAllLayoutHolesUpToEndOfContainerForGlyphIndex + 653 8 com.apple.AppKit 0x00007fff841e0c72 -[NSLayoutManager textContainerForGlyphAtIndex:effectiveRange:] + 243 9 com.apple.AppKit 0x00007fff840f6786 -[NSLayoutManager glyphRangeForTextContainer:] + 286 10 com.apple.AppKit 0x00007fff846664a9 -[NSToolTipStringDrawingLayoutManager _sizeWithSize:attributedString:] + 883 11 com.apple.AppKit 0x00007fff84665dad +[NSToolTipStringDrawingLayoutManager sizeForDisplayingAttributedString:] + 354 12 com.apple.AppKit 0x00007fff84667292 -[NSToolTipManager displayToolTip:] + 616 13 com.apple.AppKit 0x00007fff846657d4 toolTipTimerFired + 114 14 com.apple.CoreFoundation 0x00007fff8535b708 __CFRunLoopRun + 6488 15 com.apple.CoreFoundation 0x00007fff853598df CFRunLoopRunSpecific + 575 16 com.apple.HIToolbox 0x00007fff88510ada RunCurrentEventLoopInMode + 333 17 com.apple.HIToolbox 0x00007fff885108df ReceiveNextEventCommon + 310 18 com.apple.HIToolbox 0x00007fff88510798 BlockUntilNextEventMatchingListInMode + 59 19 com.apple.AppKit 0x00007fff840d1a2a _DPSNextEvent + 708 20 com.apple.AppKit 0x00007fff840d1379 -[NSApplication nextEventMatchingMask:untilDate:inMode:dequeue:] + 155 21 com.apple.AppKit 0x00007fff8409705b -[NSApplication run] + 395 22 com.apple.AppKit 0x00007fff8408fd7c NSApplicationMain + 364 23 com.NZBVortex.NZBVortex 0x0000000100000fe0 start + 52 Weirdly enough the crashes seem to go away for these users when running the code in 32 bit mode. Any suggestions other then running the application in 32 bit only? Please do not dilute the feedback by asking for or blaming the code, the code is 100% solid, guaranteed! No memory leaks, the crashes clearly are triggered in 32 bit mode only just after start inside the AppKit itself like deep inside NSThread sleep's callstack.

  Read the article

• Is the W3 standard a major factor when google decides SERP position?

  - by Camran

  I have a dynamic php website which index only has around 800 errors according to the w3 validator online. I have tried checking major websites like ebay, stackoverflow and others also, all with around 400 errors. So my first thought is, what good is that validator when it always displays errors? Secondly, will the errors affect my SERP ranking? ie, will me fixing these errors as good as I can increase my Google search position? Thanks

  Read the article

• What is the major stabilization factor in Linux ecosystem?

  - by developer

  The number of components in Linux ecosystem is permanently growing up. There are about thousands libraries, thousands device drivers, tens of thousands applications and tens of millions lines of code in the kernel maintained by thousands of volunteers. What is the greatest invention in the Linux/OSS that simplifies, organizes and stabilizes the development and growth of the platform? What is the major stabilization factor?

  Read the article

• Is the W3 standard a major factor when google decides SERP position?

  - by Anonymous12345

  I have a dynamic php website which index only has around 800 errors according to the w3 validator online. I have tried checking major websites like ebay, stackoverflow and others also, all with around 400 errors. So my first thought is, what good is that validator when it always displays errors? Secondly, will the errors affect my SERP ranking? ie, will me fixing these errors as good as I can increase my Google search position? Thanks

  Read the article

• Vimdiff with git mergetool error: "More than two buffers in diff mode"

  - by Elizabeth Buckwalter

  I've read Vimdiff and Viewing differences with Vimdiff plus doing various google searches using things like "vimdiff multiple", "vimdiff git", "vimdiff commands" etc. When using do or diffg I get the error "More than two buffers in diff mode, don't know which one to use". When using diffg v:fname_in I get "No matching buffer for v:fname_in". From the vimdiff documentation: :[range]diffg[et] [bufspec] Modify the current buffer to undo difference with another buffer. If [bufspec] is given, that buffer is used. If [bufspec] refers to the current buffer then nothing happens. Otherwise this only works if there is one other buffer in diff mode. and more: When 'diffexpr' is not empty, Vim evaluates to obtain a diff file in the format mentioned. These variables are set to the file names used: v:fname_in original file v:fname_new new version of the same file v:fname_out resulting diff file So, I need to get the name of bufspec, but the default variables (fname_in, fname_new, and fname_out) aren't set. I ran the command git mergetool on a linux box through a terminal.

  Read the article

• UIViewAnimationTransitionCurlUp in landscape mode transitioning right-to-left

  - by Thanos

  I have a view controller that is showing in portrait mode. When you touch the "menu" button, it calls the code below and it flips up to the MainMenu controller. So far, so good. - (void) menuButton: (id) sender { MainMenu_ViewController * viewController = [[MainMenu_ViewController alloc] initWithNibName:@"MainMenu_ViewController" bundle:nil]; self.menuView = viewController.view; self.menuView.frame = self.view.bounds; [viewController release]; [UIView beginAnimations:nil context: nil]; [UIView setAnimationDuration: 1.0]; [UIView setAnimationTransition: UIViewAnimationTransitionCurlUp forView: self.view cache: YES]; [self.view addSubview: self.menuView]; [UIView commitAnimations]; } However, when you do the same in landscape mode, instead of the animation flipping up (with respect to gravity, i.e. towards the long end of the iPhone) it flips towards the left (i.e. towards the short end of the iPhone). Is this a limitation of the animation, or am I missing something?

  Read the article

• ASP.NET 2.0 app runs on Win 2003 in IIS 5 isolation mode but not in (default) IIS 6 mode

  - by Tex

  The app uses DLLImport to call a legacy unmanaged dll. Let's call this dll Unmanaged.dll for the sake of this question. Unmanaged.dll has dependencies on 5 other legacy dll's. All of the legacy dll's are placed in the WebApp/bin/ directory of my ASP.NET application. When IIS is running in 5.0 isolation mode, the app works fine - calls to the legacy dll are processed without error. When IIS is running in the default 6.0 mode, the app is able to initiate the Unmanaged.dll (InitMe()), but dies during a later call to it (ProcessString()). I'm pulling my hair out here. I've moved the unmanaged dll's to various locations, tried all kinds of security settings and searched long and hard for a solution. Help! Sample code: [DllImport("Unmanaged.dll", EntryPoint="initME", CharSet=System.Runtime.InteropServices.CharSet.Ansi, CallingConvention=CallingConvention.Cdecl)] internal static extern int InitME(); //Calls to InitMe work fine - Unmanaged.dll initiates and writes some entries in a dedicated log file [DllImport("Unmanaged.dll", EntryPoint="processString", CharSet=System.Runtime.InteropServices.CharSet.Ansi, CallingConvention=CallingConvention.Cdecl)] internal static extern int ProcessString(string inStream, int inLen, StringBuilder outStream, ref int outLen, int maxLen); //Calls to ProcessString cause the app to crash, without leaving much of a trace that I can find so far

  Read the article

• FreeRTOS Sleep Mode hazards while using MSP430f5438

  - by michael

  Hi, I wrote an an idle hook shown here void vApplicationIdleHook( void ) { asm("nop"); P1OUT &= ~0x01;//go to sleep lights off! LPM3;// LPM Mode - remove to make debug a little easier... asm("nop"); } That should cause the LED to turn off, and MSP430 to go to sleep when there is nothing to do. I turn the LED on during some tasks. I also made sure to modify the sleep mode bit in the SR upon exit of any interrupt that could possibly wake the MCU (with the exception of the scheduler tick isr in portext.s43. The macro in iar is __bic_SR_register_on_exit(LPM3_bits); // Exit Interrupt as active CPU However, it seems as though putting the MCU to sleep causes some irregular behavior. The led stays on always, although when i scope it, it will turn off for a couple instructions cycles when ever i wake the mcu via one of the interrupts (UART), and then turn back on. If I comment out the LPM3 instruction, things go as planned. The led stays off for most of the time and only comes on when a task is running. I am using a MSP4f305438 Any ideas?

  Read the article

• Running Hadoop example in psuedo-distributed mode on vm

  - by manas

  I have set-up Hadoop on a OpenSuse 11.2 VM using Virtualbox.I have made the prerequisite configs. I ran this example in the Standalone mode successfully. But in psuedo-distributed mode I get the following error: $./bin/hadoop fs -put conf input 10/04/13 15:56:25 INFO hdfs.DFSClient: Exception in createBlockOutputStream java.net.SocketException: Protocol not available 10/04/13 15:56:25 INFO hdfs.DFSClient: Abandoning block blk_-8490915989783733314_1003 10/04/13 15:56:31 INFO hdfs.DFSClient: Exception in createBlockOutputStream java.net.SocketException: Protocol not available 10/04/13 15:56:31 INFO hdfs.DFSClient: Abandoning block blk_-1740343312313498323_1003 10/04/13 15:56:37 INFO hdfs.DFSClient: Exception in createBlockOutputStream java.net.SocketException: Protocol not available 10/04/13 15:56:37 INFO hdfs.DFSClient: Abandoning block blk_-3566235190507929459_1003 10/04/13 15:56:43 INFO hdfs.DFSClient: Exception in createBlockOutputStream java.net.SocketException: Protocol not available 10/04/13 15:56:43 INFO hdfs.DFSClient: Abandoning block blk_-1746222418910980888_1003 10/04/13 15:56:49 WARN hdfs.DFSClient: DataStreamer Exception: java.io.IOException: Unable to create new block. at org.apache.hadoop.hdfs.DFSClient$DFSOutputStream.nextBlockOutputStream(DFSClient.java:2845) at org.apache.hadoop.hdfs.DFSClient$DFSOutputStream.access$2000(DFSClient.java:2102) at org.apache.hadoop.hdfs.DFSClient$DFSOutputStream$DataStreamer.run(DFSClient.java:2288) 10/04/13 15:56:49 WARN hdfs.DFSClient: Error Recovery for block blk_-1746222418910980888_1003 bad datanode[0] nodes == null 10/04/13 15:56:49 WARN hdfs.DFSClient: Could not get block locations. Source file "/user/max/input/core-site.xml" - Aborting... put: Protocol not available 10/04/13 15:56:49 ERROR hdfs.DFSClient: Exception closing file /user/max/input/core-site.xml : java.net.SocketException: Protocol not available java.net.SocketException: Protocol not available at sun.nio.ch.Net.getIntOption0(Native Method) at sun.nio.ch.Net.getIntOption(Net.java:178) at sun.nio.ch.SocketChannelImpl$1.getInt(SocketChannelImpl.java:419) at sun.nio.ch.SocketOptsImpl.getInt(SocketOptsImpl.java:60) at sun.nio.ch.SocketOptsImpl.sendBufferSize(SocketOptsImpl.java:156) at sun.nio.ch.SocketOptsImpl$IP$TCP.sendBufferSize(SocketOptsImpl.java:286) at sun.nio.ch.OptionAdaptor.getSendBufferSize(OptionAdaptor.java:129) at sun.nio.ch.SocketAdaptor.getSendBufferSize(SocketAdaptor.java:328) at org.apache.hadoop.hdfs.DFSClient$DFSOutputStream.createBlockOutputStream(DFSClient.java:2873) at org.apache.hadoop.hdfs.DFSClient$DFSOutputStream.nextBlockOutputStream(DFSClient.java:2826) at org.apache.hadoop.hdfs.DFSClient$DFSOutputStream.access$2000(DFSClient.java:2102) at org.apache.hadoop.hdfs.DFSClient$DFSOutputStream$DataStreamer.run(DFSClient.java:2288) Any leads will be highly appreciated.

  Read the article

• Error building Visual Studio 2010 Silverlight 4 projects on Windows 7 with XP Mode

  - by Kevin Dente

  I installed Visual Studio 2010 Beta 2 in an XP Mode VM on Windows 7. Then I created a trivial Silverlight 4 (beta) project and tried to build it. I get the following error: Error 1 The "ValidateXaml" task failed unexpectedly. System.IO.FileLoadException: Could not load file or assembly 'file://\tsclient\d\Users\me\Documents\Visual Studio 2010\Projects\SilverlightApplication2\SilverlightApplication2\obj\Debug\SilverlightApplication2.dll' or one of its dependencies. Operation is not supported. (Exception from HRESULT: 0x80131515) File name: 'file://\tsclient\d\Users\me\Documents\Visual Studio 2010\Projects\SilverlightApplication2\SilverlightApplication2\obj\Debug\SilverlightApplication2.dll' --- System.NotSupportedException: An attempt was made to load an assembly from a network location which would have caused the assembly to be sandboxed in previous versions of the .NET Framework. This release of the .NET Framework does not enable CAS policy by default, so this load may be dangerous. If this load is not intended to sandbox the assembly, please enable the loadFromRemoteSources switch. See http://go.microsoft.com/fwlink/?LinkId=155569 for more information. at System.Reflection.RuntimeAssembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, RuntimeAssembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, RuntimeAssembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoadAssemblyName(AssemblyName assemblyRef, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoadFrom(String assemblyFile, Evidence securityEvidence, Byte[] hashValue, AssemblyHashAlgorithm hashAlgorithm, Boolean forIntrospection, Boolean suppressSecurityChecks, StackCrawlMark& stackMark) at System.Reflection.Assembly.LoadFrom(String assemblyFile) at Microsoft.Silverlight.Build.Tasks.ValidateXaml.XamlValidator.Execute(ITask task) at Microsoft.Silverlight.Build.Tasks.ValidateXaml.XamlValidator.Execute(ITask task) at Microsoft.Silverlight.Build.Tasks.ValidateXaml.Execute() at Microsoft.Build.BackEnd.TaskExecutionHost.Microsoft.Build.BackEnd.ITaskExecutionHost.Execute() at Microsoft.Build.BackEnd.TaskBuilder.ExecuteInstantiatedTask(ITaskExecutionHost taskExecutionHost, TaskLoggingContext taskLoggingContext, TaskHost taskHost, ItemBucket bucket, TaskExecutionMode howToExecuteTask, Boolean& taskResult) I believe this is related to the fact that XP Mode redirects the My Documents folder to the host, turning it into a network share location, and some sort of CAS / security policy is being triggered. Anyone know how to fix it?

  Read the article

• How to do recurring with bank account payment mode using authorized.net

  - by Salil

  Hi All, I am using recurring facility of authorized.net using active_merchant plugin in rails. there are two payment method for this 1] Credit Card 2] Bank Account I successfully done it using Credit Card For Recurring i need my Test Mode off. Also my E-check, credit card processing, and subscriptions are all enabled. But i am not able to subscribed using Bank Account Following is my code ActiveMerchant::Billing::Base.mode = :developer #i found follwing test bank account on net account = ActiveMerchant::Billing::Check.new(:account_holder_type=>"personal",:account_number=>"123123123", :account_type => "savings", :name=>"name", :routing_number=>"244183602") if account.valid? #this comes true gateway = ActiveMerchant::Billing::AuthorizeNetGateway.new(:login => 'Mylogin', :password => 'Mypassword') response = gateway.recurring( amount, nil, {:interval =>{:length=>@length, :unit =>:months}, :duration =>{:start_date=>'2010-04-24', :occurrences=>1}, :billing_address=>{:first_name=>'dinesh', :last_name=>'singh'}, :bank_account=>{:account_holder_type=>"personal",:account_number=>"123123123", :account_type => "savings", :name_of_account=>"name", :routing_number=>"244183602"} }) if response.success? #this comes false else puts response.message ####>> ERROR render :action=>"account_payment" end I get Follwing ERROR when i debug for response.message "The test transaction was not successful. (128) This transaction cannot be processed." Am i doing anything wrong i search for the another Test Bank Account Data but i didn't find it. Please help I badly need it. Thanks in Advance. Regards, Salil Gaikwad

  Read the article

• Timer a usage in msp430 in high compiler optimization mode

  - by Vishal

  Hi, I have used timer A in MSP430 with high compiler optimization, but found that my timer code is failing when high compiler optimization used. When none optimization is used code works fine. This code is used to achieve 1 ms timer tick. timeOutCNT is increamented in interrupt. Following is the code, //Disable interrupt and clear CCR0 TIMER_A_TACTL = TIMER_A_TASSEL | // set the clock source as SMCLK TIMER_A_ID | // set the divider to 8 TACLR | // clear the timer MC_1; // continuous mode TIMER_A_TACTL &= ~TIMER_A_TAIE; // timer interrupt disabled TIMER_A_TACTL &= 0; // timer interrupt flag disabled CCTL0 = CCIE; // CCR0 interrupt enabled CCR0 = 500; TIMER_A_TACTL &= TIMER_A_TAIE; //enable timer interrupt TIMER_A_TACTL &= TIMER_A_TAIFG; //enable timer interrupt TACTL = TIMER_A_TASSEL + MC_1 + ID_3; // SMCLK, upmode timeOutCNT = 0; //timeOutCNT is increased in timer interrupt while(timeOutCNT <= 1); //delay of 1 milisecond TIMER_A_TACTL = TIMER_A_TASSEL | // set the clock source as SMCLK TIMER_A_ID | // set the divider to 8 TACLR | // clear the timer MC_1; // continuous mode TIMER_A_TACTL &= ~TIMER_A_TAIE; // timer interrupt disabled TIMER_A_TACTL &= 0x00; // timer interrupt flag disabled Can anybody help me here to resolve this issue? Is there any other way we can use timer A so it works fine in optimization modes? Or do I have used is wrongly to achieve 1 ms interrupt? Thanks in advanced. Vishal N

  Read the article

• Datagridview Winforms Add or Delete Rows in Edit Mode with Collection Binding

  - by user630548

  In my datagridview, I bind a List of objects named 'ProductLine'. But unfortunately with this approach I cannot 'Add' or 'Delete' rows to the datagridview in edit mode. When I create a fresh new order I can Add or Delete rows but once I save it and try to open it in Edit then it doesn't let me 'Add' or 'Delete' (via keyboard). Any idea? Here is the code for this: If it is a fresh Order then I do something like this: private void Save(){ for (int i = 0; i <= dtgProdSer.RowCount - 1; i++) { if ((itemList != null) && (itemList.Count > i)) productLine = itemList[i]; else productLine = new ProductLine(); productLine.Amount = Convert.ToDouble(dataGridViewTextBoxCell.Value); } } And if it is an Edit then in the Form_Load I check ProductId is NON Zero then I do the following: private void fillScreen{ dtgProdSer.DataSource = itemList; } But with this I cannot Add or Delete Rows in Edit mode. Any advise is greatly appreciated.

  Read the article

• IIS7 integrated mode MVC deploy 404 not found on some actions

  - by majkinetor

  Hello. Once deployed parts of my web-application stop working. Index-es on each controller do work, and one form posting via Ajax, other then that yields 404. I understand that nothing particular should be done in integrated mode. One interesting thing is that 1 AJAX action is working. I don't know how to proceed with troubleshooting. Some info: App is using default app pool set to integrated mode. WebApp is done in net framework 3.5. I use default routing model. Along web.config in root there is web.config in /View folder referencing HttpNotFoundHandler. OS is Windows Server 2008. Admins issued aspnet_regiis.exe -i IIS 7 Any help is appreciated. Thx. EDIT: Noticed one very strange thing. One ajax call works, other ajax call doesn't works as I login, but when I move to ther page and return to that one it starts working ?! Small video of the problem is available here

  Read the article

• Getting error when compiling debug mode: C++/CLI - error LNK2022

  - by Yochai Timmer

  I've got a CLI code wrapping a C++ DLL. When i try to compile it in debug mode, i get the following error: Error 22 error LNK2022: metadata operation failed (8013118D) : Inconsistent layout information induplicated types .... MSVCMRTD.lib (locale0_implib.obj) The weird thing is that on Release mode it compiles OK and works OK. The only difference i can see that causes the problem is when i change: Configuration Properties - C/C++ - Code Generation - Runtime Library When it's set to: Multi-threaded Debug DLL (/MDd) it throws the error. When it's set to: Multi-threaded DLL (/MD) it compiles fine. The same settings work for all the other DLLs in the project (CLI and C++) and they inherit the same properties. I'm using VS2010. So, how can i solve this ? And can I get some explanation to WHY this is happening ? Update: I've basically tried changing every option in the project's properties with no luck. I've read somewhere that this might be caused from duplicate declarations of a type of the same name. But in the CLI file i'm calling std::string etc. explicitly from std. Any other ideas ?

  Read the article

• How to resolve the only ImagePicker control view in landscap mode and whole application in portrait mode?

  - by Wolvorin

  I have tried almost all the answers during last two days provided by Google and SO but no luck :( What I want is my whole application is in portrait mode only. And it working fine in ios 6+. The only support required at now. But the problem is I need to launch UIImagePickerViewController with image source type camera in only landscap mode. What I tried till now is : (1) I try to create one category for UIImagePickerController for orientation. -(BOOL)shouldAutorotate { return NO; } -(NSUInteger)supportedInterfaceOrientations { return UIInterfaceOrientationMaskLandscape; } - (UIInterfaceOrientation)preferredInterfaceOrientationForPresentation { return UIInterfaceOrientationLandscapeLeft; } Like this. But the camera view is not proper aligned. It just follows the orientation of device with some +/- 90 angle but not what I required. Even the button of the camera shown by camera view as camera control is also follows the camera view, ie. the view is rotated to 90 anti clock vise and stays to that way. Is there any way to use the camera with proper alignment? or have to use other framework to work with it? Please help me. I stuck with it for last two days.

  Read the article

• OnConnect event not firing when using TClientSocket inside a TThread on non-blocking mode

  - by mathematician1975

  I am trying to make use of Borlands TClientSocket component in non-blocking mode inside a multithreaded C++ Windows application. I am creating multiple threads (classes derived from TThread), each of which creates its own TClientSocket object. I then assign member functions of the thread class to act as event handlers for the OnConnect, OnDisconnect and OnSocketError events of the socket. The problem I am having here is that whenever I call the TClientSocket::Open() function from within the TThread::Execute() function, the OnConnect event never fires. However, When I call the Open() function from the VCL thread prior to the TThread::Execute() function getting called, all of the events fire and I can use the thread-socket combination as I would like. Now I have not read anything in documentation that says that TClientSocket should not be used in non-blocking mode when used inside a thread, but it appears to me that there is perhaps something wrong conceptually in the way I am trying to use this class. Borland documentation is quite poor on the subject and these components have now been deprecated so reliable information is hard to come by. Despite being deprecated I have to use them as there is no alternative in the Builder 6 package I have. Can anyone please advise me if there is a right/wrong way to use TThread and a non-blocking TClientSocket in combination. I have never had problems using it as part of the VCL thread and never had problems using TServerSocket before and I really cannot understand why some events are not firing.

  Read the article

• Open an Emacs buffer when a command tries to open an editor in shell-mode

  - by Chris Conway

  I like to use Emacs' shell mode, but it has a few deficiencies. One of those is that it's not smart enough to open a new buffer when a shell command tries to invoke an editor. For example with the environment variable VISUAL set to vim I get the following from svn propedit: $ svn propedit svn:externals . "svn-prop.tmp" 2L, 149C[1;1H ~ [4;1H~ [5;1H~ [6;1H~ [7;1H~ ... (It may be hard to tell from the representation, but it's a horrible, ugly mess.) With VISUAL set to "emacs -nw", I get $ svn propedit svn:externals . emacs: Terminal type "dumb" is not powerful enough to run Emacs. It lacks the ability to position the cursor. If that is not the actual type of terminal you have, use the Bourne shell command `TERM=... export TERM' (C-shell: `setenv TERM ...') to specify the correct type. It may be necessary to do `unset TERMINFO' (C-shell: `unsetenv TERMINFO') as well.svn: system('emacs -nw svn-prop.tmp') returned 256 (It works with VISUAL set to just emacs, but only from inside an Emacs X window, not inside a terminal session.) Is there a way to get shell mode to do the right thing here and open up a new buffer on behalf of the command line process?

  Read the article

< Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >