Search Results

Search found 18964 results on 759 pages for 'network balancing'.

Page 37/759 | < Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >

• Gigabit network limited to 25MB/s by CPU. How to make it faster?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• Connection to openVPN Access Server

  - by Beig

  we are using an openVPN Access Server and I would like to connect to it via the VPN network setting (network-manager-openvpn). I downloaded the client.ovpn and I can connect to the server via the command line: openvpn --script-security 2 --config client.ovpn How can I add the connection to the network manager? Which (key) entry is which? User Cert, CA Cert, Private Key? Here is an example of the client.ovpn http://nopaste.info/c10ec207f2.html Thanks in advance.

  Read the article

• Difference between all servers in one cluster and more than one cluster with servers?

  - by silla

  Not sure I understand what´s the difference or how it works when servers a running in one cluster or if there are more than one clusters with servers in it - regard High availability & Load Balancing. For me they are somehow the same, there is not really a big difference. Let´s make a simple example: 2 Servers in 1 Cluster 2 Clusters with each 1 Server - 1. If one Server failure, the other one is able to continue the work. The same for Load Balancing, these two Servers are able to balance the work together. - 2. The same thing! If one Server failure... The only thing that could be a problem with point 1. is if the Cluster fails (then both of the Server are dead). But is this even possible? I was reading stuff about clustering and high availability but I think I do not get this really. Probably I did not really understand how a cluster is working. Are these 2 points with 1 Cluster and 2 Clusters somehow the same or are there really some big differences? What should I know about it? Thank you

  Read the article

• NM applet dropdown options not working

  - by Prarobo

  I recently realized the dropdown options from my nm-applet are no longer working. But I can still control the network configuration by going through the dash. This happened very recently. I only realized this before a week. I guess some recent update screwed it up. I have these related packages installed network-manager-gnome 0.9.4.1-0ubuntu2 libnm-gtk0 0.9.4.1-0ubuntu2 network-manager 0.9.4.0-0ubuntu4.1 Any help would be great.

  Read the article

• Network Your Computers & Devices: Step by Step

  - by The Geek

  If you’re looking for a great book to help you learn more about Windows home networking, there’s a new book on the market by our good friend Ciprian, and published by none other than Microsoft Press. Note: our friend Ciprian has been a guest contributor here on How-To Geek in the past, and he’s not only a geek that knows what he’s talking about, he’s also one of the more honest and decent people I’ve worked with. In his spare time, he runs the 7 Tutorials web site. The Book One of the great things about this book is that you aren’t limited to just Windows networking—it also explains how to connect Windows 7, XP, Vista, Mac OS X, and even Linux on the same network and share folders and devices between them. Everything in the book is written in a typical How-To Geek step-by-step format, with plenty of screenshots and pictures to help you through the process. Book Outline If you’re going to be spending some money on the book, you probably want to know what it’s all about, and since the Amazon page doesn’t give, well, much information at all, here’s the entire outline for you: Setting Up a Router and Devices Setting User Account on All Computers Setting Up Your Libraries on All Windows 7 Computers Creating the Network Customizing Network Sharing Settings in Windows 7 Creating the Homegroup and Joining Windows 7 Computers Sharing Libraries and Folders Sharing and Working with Devices Streaming Media Over the Network and the Internet Sharing Between Windows XP, Windows Vista, and Windows 7 Computers Sharing Between Mac OS X and Windows 7 Computers Sharing Between Ubuntu Linux and Windows 7 Computers Keeping the Network Secure Setting Up Parental Controls Troubleshooting Network and Internet Problems It’s a great book, with loads of information, and compared to most tech books isn’t very expensive—only $19.79 for the paperback and $9.99 for the Kindle version. Well worth it, and hey, it’s an official Microsoft Press book—written by a How-To Geek guest author. Network Your Computers & Devices Step by Step [Amazon] Latest Features How-To Geek ETC How To Boot 10 Different Live CDs From 1 USB Flash Drive The 20 Best How-To Geek Linux Articles of 2010 The 50 Best How-To Geek Windows Articles of 2010 The 20 Best How-To Geek Explainer Topics for 2010 How to Disable Caps Lock Key in Windows 7 or Vista How to Use the Avira Rescue CD to Clean Your Infected PC 2011 International Space Station Calendar Available for Download (Free) Ultimate Elimination – Lego Black Ops [Video] BotSync Enables Secure FTP File Synchronization on Android Devices Enjoy Beautiful City Views with the Cityscape Theme for Windows 7 Luigi Installs Any OS on Google’s Cr-48 Notebook DIY iPad Stylus Offers Pen-Based Interaction on the Cheap

  Read the article

• Oracle Social Network Developer Challenge: HarQen Nodal

  - by Kellsey Ruppel

  Originally posted by Jake Kuramoto on The Apps Lab blog. We wrapped the Oracle Social Network Developer Challenge last week at OpenWorld, and this week, I’ll be sharing all the entries. All the teams that entered our challenge did a ton of work and built really interesting integrations with Oracle Social Network, and I want to showcase their hard work and innovative ideas. Today, I give you Nodal from the HarQen (@harqen) team, Kris Gösser (@krisgosser), Jesse Vogt (@jesse_vogt) and Matt Stockton (@mstockton). The guys from HarQen built Nodal to provide a visual way to navigate your connections and conversations in Oracle Social Network and view relationships. Using Nodal, you can: Search through names and profiles in Oracle Social Network. Choose people and view their social graphs in a visually useful way. Expand nodes in the social graph and add that person’s social graph to the Nodal view for comparison. Move nodes around and lock them in place for easier viewing, using a physics engine for movement. Adjust the physics engine properties according to your viewing preferences. Select nodes in the social graph and create a conversation directly based on the selection. Here are some shots of Nodal. They really don’t do the physics engine justice, but maybe the guys at Harqen will post a video of what they did for your viewing pleasure. #gallery-1 { margin: auto; } #gallery-1 .gallery-item { float: left; margin-top: 10px; text-align: center; width: 33%; } #gallery-1 img { border: 2px solid #cfcfcf; } #gallery-1 .gallery-caption { margin-left: 0; }   Nodal’s visuals wowed the judges and the audience, and anyone with a decent-sized social network presence understands the need for good network visualization. Tools like Nodal allow you to discover hidden connections in your network and maximize the value of your weak ties and find mavens, a very important key to getting work done. Thanks to the HarQen team for participating in our challenge. We hope they had a good experience. Look for the details of the other entries this week.

  Read the article

• Weighted round robins via TTL - possible?

  - by Joe Hopfgartner

  I currently use DNS round robin for load balancing, which works great. The records look like this (I have a ttl of 120 seconds) ;; ANSWER SECTION: orion.2x.to. 116 IN A 80.237.201.41 orion.2x.to. 116 IN A 87.230.54.12 orion.2x.to. 116 IN A 87.230.100.10 orion.2x.to. 116 IN A 87.230.51.65 I learned that not every ISP / device treats such a response the same way. For example some DNS servers rotate the addresses randomly or always cycle them through. Some just propagate the first entry, others try to determine which is best (regionally near) by looking at the ip address. However if the userbase is big enough (spreads over multiple ISPs etc) it balances pretty well. The discrepancies from highest to lowest loaded server hardly every exceeds 15%. However now I have the problem that I am introducing more servers into the systems, that not all have the same capacities. I currently only have 1gbps servers, but I want to work with 100mbit and also 10gbps servers too. So what I want is I want to introduce a server with 10 GBps with a weight of 100, a 1 gbps server with a weight of 10 and a 100 mbit server with a weight of 1. I used to add servers twice to bring more traffic to them (which worked nice. the bandwidth doubled almost.) But adding a 10gbit server 100 times to DNS is a bit rediculous. So I thought about using the TTL. If I give server A 240 seconds ttl and server B only 120 seconds (which is about about the minimum to use for round robin, as a lot of dns servers set to 120 if a lower ttl is specified.. so i have heard) I think something like this should occour in an ideal scenario: first 120 seconds 50% of requests get server A -> keep it for 240 seconds. 50% of requests get server B -> keep it for 120 seconds second 120 seconds 50% of requests still have server A cached -> keep it for another 120 seconds. 25% of requests get server A -> keep it for 240 seconds 25% of requests get server B -> keep it for 120 seconds third 120 seconds 25% will get server A (from the 50% of Server A that now expired) -> cache 240 sec 25% will get server B (from the 50% of Server A that now expired) -> cache 120 sec 25% will have server A cached for another 120 seconds 12.5% will get server B (from the 25% of server B that now expired) -> cache 120sec 12.5% will get server A (from the 25% of server B that now expired) -> cache 240 sec fourth 120 seconds 25% will have server A cached -> cache for another 120 secs 12.5% will get server A (from the 25% of b that now expired) -> cache 240 secs 12.5% will get server B (from the 25% of b that now expired) -> cache 120 secs 12.5% will get server A (from the 25% of a that now expired) -> cache 240 secs 12.5% will get server B (from the 25% of a that now expired) -> cache 120 secs 6.25% will get server A (from the 12.5% of b that now expired) -> cache 240 secs 6.25% will get server B (from the 12.5% of b that now expired) -> cache 120 secs 12.5% will have server A cached -> cache another 120 secs ... i think i lost something at this point but i think you get the idea.... As you can see this gets pretty complicated to predict and it will for sure not work out like this in practice. But it should definitely have an effect on the distribution! I know that weighted round robin exists and is just controlled by the root server. It just cycles through dns records when responding and returns dns records with a set propability that corresponds to the weighting. My DNS server does not support this, and my requirements are not that precise. If it doesnt weight perfectly its okay, but it should go into the right direction. I think using the TTL field could be a more elegant and easier solution - and it deosnt require a dns server that controls this dynamically, which saves resources - which is in my opinion the whole point of dns load balancing vs hardware load balancers. My question now is... are there any best prectices / methos / rules of thumb to weight round robin distribution using the TTL attribute of DNS records? Edit: The system is a forward proxy server system. The amount of Bandwidth (not requests) exceeds what one single server with ethernet can handle. So I need a balancing solution that distributes the bandwidth to several servers. Are there any alternative methods than using DNS? Of course I can use a load balancer with fibre channel etc, but the costs are rediciulous and it also increases only the width of the bottleneck and does not eliminate it. The only thing i can think of are anycast (is it anycast or multicast?) ip addresses, but I don't have the means to set up such a system.

  Read the article

• Internal+external interfaces with multiple default gateways on win2003

  - by fileitup

  Im trying to set up several web servers for a load balanced cluster and need to have each server connected to the internal network (for load balancing) as well as to an external network (internet - for administration). I have two NICs but since I cant set two default gateways I have the external gateway as default and the internal as a route rule. This setup only works half way - the internal network is fine but I cant log in from outside or see the web from the box. If I switch the gateways remote login/web will work, but the internal wont. Im sure someone encountered this before but wasnt able to find anything online. Any help will be appreciated.

  Read the article

• What are some topics you'd like to see covered in an 'Introduction to Network Security' book?

  - by seth.vargo

  I'm trying to put together a list of topics in Network Security and prioritize them accordingly. A little background on the book - we are trying to gear the text towards college students, as an introduction to security, and toward IT professionals who have recently been tasked with securing a network. The idea is to create a book that covers the most vital and important parts of securing a network with no assumptions. So, if you were a novice student interested in network security OR an IT professional who needed a crash course on network security, what topics do you feel would be of the upmost importance in such a text?

  Read the article

• Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect

  - by user287529

  Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect. I'm using Ubuntu 12.04 on an Acer Aspire 5742-7645 laptop with 4GB memory, Intel Core i3 processor, Intel HD Graphics, DVD drive, 802.1 b/g/n, and 500 GB HD. I connect to my router via a wireless connection. I have installed Virutalbox 4.1.12 from the Ubuntu Software Center and installed Guest additions 4.1.12 in the Windows 7 guest session. I have Windows XP and Windows 7 installed as guests in Virtual box The network settings are different for XP and 7 – see below. Network Settings XP guest = Adapter 1: PCnet-FAST III (NAT) - Network works perfectly and has worked well for several years. Network Settings Win 7 = Adapter 1: Intel PRO/1000 MT Desktop (Bridged adapter, eth1) Promiscuous Mode = allow all Cable connected = checked When I originally installed Windows 7, I tried NAT and the guest network would not connect. Once I changed the setting to the above (Bridged) the Network worked perfectly. However, what I believe is after updates (not sure if it was an Ubuntu or Windows update) the guest network stopped working and I can not get it to connect. Interfaces file content auto lo iface lo inet loopback Ifconfig yields lou@lou-Aspire-5742:~$ ifconfig eth0 Link encap:Ethernet HWaddr 1c:75:08:09:f6:5c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 Link encap:Ethernet HWaddr 4c:0f:6e:7c:9f:01 inet addr:192.168.1.104 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4e0f:6eff:fe7c:9f01/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18095 errors:2 dropped:0 overruns:0 frame:24344 TX packets:9281 errors:47 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5301926 (5.3 MB) TX bytes:1441885 (1.4 MB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3208 errors:0 dropped:0 overruns:0 frame:0 TX packets:3208 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:294088 (294.0 KB) TX bytes:294088 (294.0 KB) Ipconfig yields the following: Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::38ba:dbca:a21d:c3d1%13 Autoconfiguration IPv4 Address. . : 169.254.195.209 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{B292E440-679D-4FC5-8E34-77D6804669C8}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : I'm not sure what else to do. Can someone provide the troubleshooting steps to determine what the problem is and possible solution?

  Read the article

• Network communication across two private network

  - by Sethu

  Hi All, I am trying to implement a peer to peer communication .. I use sockets for communication between them. I want to know if there are any ways i can use the same sort of communication when the two peers are behind two private Networks (They dont know each others public ip address.) I can think of a shared buffer in a well known location as a means of communication. But is there some other way to get this done?

  Read the article

• my windows xp sp3 diagnostick:windows could not detect any wired or wireless network cards installed on your machine

  - by Yosef

  Problem: cant connect to internet with my new installation of windows xp sp3. Details: I have ubuntu in pc that worked with wired internet. i format all disk and install windows xp sp3. i have auto internet that defined in my router - other computers have internet. I run diagnoze of ie and get: windows could not detect any wired or wireless network cards installed on your machine In Device Manager i have only 1394 Adapter I dont see any internet adapters. Edit: I find with ubuntu livecd that i have hardware:82566dc gigabit network connection Thanks

  Read the article

• Connecting a network drive only when the VPN is connected?

  - by leeand00

  I have a thumb drive that I want to be able to connect to the same place over the network at one location as it is locally. Sometimes I leave it at the other location, but usually if I'm going to back it up, I back it up locally for network traffic. Is there a way to automatically connect the thumb drive when I connect to the VPN? (Always to the same drive letter...and obviously skip connecting it if it's already plugged in locally and the VPN is connected...) I'm using a Cisco VPN Client 5.x

  Read the article

• How do you confirm network adapter is gigabit capable?

  - by StrandedPirate

  Upgrading my network to gigabit speeds and don't know how to determine if the NIC in one of the systems is capable of gigabit speed. The documentation from the manufacturer states this: Network adapter 10/100/1000 Ethernet LAN on system board However when I go to the properties of the NIC under Speed & Duplex my only options are: 10 Mb Full 10 Mb Half 100 Mb Full 100 Mb Half Auto Is there a command line I can run that will give me more detail about the NIC? Windows 7 x64 OS New Info: The new switch I just bought has a light to indicate 1000Mbps. I can tell from the light that this NIC is indeed negotiating at 1000Mbps but I'd still like to know how to determine this from the console in windows.

  Read the article

• Network printer - Print direct or via shared printer on Server?

  - by NickC

  It has occurred to me that a workstation can connect to a printer in two ways: 1). Printing directly to the IP of the printer with the print driver installed locally. 2). Printing to a \Server\Printer1 share with the print queue residing on the server. Question is which way is preferred? I would assume that printing directly to a network printer rather than going through the server would be the most efficient from the point of view of network traffic. On the other hand I guess a server printer share would be easier to manage with the correct driver automatically being downloaded to the workstations. Also what about using GPP (Server2012) to install this printer on the workstations, does that require any specific way?

  Read the article

• Installing linux on a crippled machine via network boot?

  - by networkbooter

  I have a somewhat ancient Toshiba laptop (which can't boot from USB) that I want to install linux on (probably Ubuntu). I'm currently running Windows XP and Ubuntu via Wubi. I want to delete these OSs and replace with Ubuntu only. The laptop does have a network boot option. I'm wondering if the easiest way might be to setup a network boot server on my other computer (which runs Ubunutu) and boot the laptop from it. Could this allow me to install Linux on the laptop? I can't seem to find instructions on the 'net as to how to go about doing this.

  Read the article

• When an Excel file is locked on a network share, how does it know who locked the file?

  - by ScottStonehouse

  We are using Excel 2010 and sometimes users are working from a network share. When a user on the network opens the file in Excel, the file is locked for editing - this is the expected behavior. When another user tries to open the file, Excel gives the message [filename] is locked for editing by 'John Doe' The problem is, the user is always this one particular user's name, no matter who actually has the file open. Where does Excel get this info, and how do I fix it? Update: I should have mentioned that in Excel, under Options (General), the correct user names have been set up. That is not where this user name is coming from.

  Read the article

• ASA5505 Novice. Setting up Outside/Inside/and DMZ as Guest Network

  - by GriffJ

  I need a little help in developing a config for our ASA5505. I'm an MCSA/MCITPAS but I don't have a lot of practical cisco experience. Here is what I need help with, we currently have a PIX as our boarder gateway and well it's antiquated and it only has a 50 user license which means I'm constantly clearing local-host throughout the day as people complain. I discovered that the last IT person bought at couple ASA5505s and they've been sitting in the back of a cupboard. So far I've duplicated the configuration from the pix to the asa but as I was going to be going this far I thought I'd go further and remove another old cisco router that was used only for the guest network, I know the asa can do both jobs. So I'm going to paste a scenario I wrote up with the actual IPs changed to protect the innocent. ... Outside Network: 1.2.3.10 255.255.255.248 (we have a /29) Inside Network: 10.10.36.0 255.255.252.0 DMZ Network: 192.168.15.0 255.255.255.0 Outside Network on e0/0 DMZ Network on e0/1 Inside Network on e0/2-7 DMZ Network has DHCPD Enabled. DMZ DHCPD Pool is 192.168.15.50-192.168.15.250 DMZ Network needs to be able to see DNS on Inside Network at 10.10.37.11 and 10.10.37.12 DMZ Network needs to be able to access webmail on inside network at 10.10.37.15 DMZ Network needs to be able to access business website on inside network at 10.10.37.17 DMZ Network needs to be able to access the outside network (access to the internet). Inside Network has NO DHCPD. (dhcp is handled by domain controller) Inside Network needs to be able to see anything on the DMZ network. Inside Network needs to be able to access the outside network (access to the internet). There is some access-list stuff already, some static mapping already. Maps external IPs from our ISP to our inside server IPs static (inside,outside) 1.2.3.11 10.10.37.15 netmask 255.255.255.255 static (inside,outside) 1.2.3.12 10.10.37.17 netmask 255.255.255.255 static (inside,outside) 1.2.3.13 10.10.37.20 netmask 255.255.255.255 Allows access to our Webserver/Mailserver/VPN from the Outside. access-list 108 permit tcp any host 1.2.3.11 eq https access-list 108 permit tcp any host 1.2.3.11 eq smtp access-list 108 permit tcp any host 1.2.3.11 eq 993 access-list 108 permit tcp any host 1.2.3.11 eq 465 access-list 108 permit tcp any host 1.2.3.12 eq www access-list 108 permit tcp any host 1.2.3.12 eq https access-list 108 permit tcp any host 1.2.3.13 eq pptp Here is all the NAT and route stuff I have so far. global (outside) 1 interface global (outside) 2 1.2.3.11-1.2.3.14 netmask 255.255.255.248 nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 1.2.3.9 1

  Read the article

• A gigabit network interface is CPU-limited to 25MB/s. How can I maximize the throughput?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? As a reference, the other computers in the network can usually transfer at 50+MB/s without problems. A computer with a Core 2 CPU generates only 5000 interrupts per second when it's transferring at 110MB/s. The number of interrupts is about 20 times less than the Atom system (if interrupts scale linearly with throughput.) And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• Building a network at home, what cables to use (if any)?

  - by Faruz

  My house is currently in ruins and am building it. While doing so, I wanted to design a home network. My main objectives are surfing and HD streaming. The house is one-level, 100 sq/m (about 300 sq/ft), and one of the rooms is a safety room with Reinforced concrete walls. About a year ago, when I started planning, I thought about putting Cat 6 STP cables in the walls and create network points in the rooms. Should I use STP or FTP? I heard that STP is a problem regarding connectors and stuff. Is it really beneficial? Will it work OK if I transfer the wire together with the telephone line? Should I maybe go with WLan and count on 802.11n to enable me to stream HD across the house? is 802.11n that good?

  Read the article

• I'd like to archive files from Ubuntu to Windows between two computers on a shared home network

  - by Wabbitseason

  I have an old laptop running Ubuntu 9.10 which I use as a LAMP environment for web development, and I have a comfortable, powerful desktop computer with Windows 7 installed on it. These two are connected to a home router so both can access the internet. I have been able to set up Samba so I can mount my Apache home directory so it is accessible from Windows and is mapped as a network drive. What I'd like to do is access some Windows folders from Linux so I could automatically create backups (with cron scripts) of my work to physically different locations on the Windows box. Perhaps at a later time I'd set up a local Subversion repository but I'd love to keep backups of that on the Windows drives too. Using Ubuntu's Places/Network menu I can see my desktop but I'm unable to log in to that despite having created the corrent username and password on Windows. All I can get is the following error message: "Unable to mount location. Failed to retrieve share list from server." What could be misconfigurated?

  Read the article

• Using a Token-ring network card instead of a router (?)

  - by John

  I have cable, and the modem only has 1 network plug-in. They said I could buy my own router if I wanted to hook up two computers to it. I have an IBM Turbo 16/4 Token-Ring PC Card 2, which was in the laptop when I bought it, and the laptop also has the typical network plug (not a PC Card). Is there a way I could run the laptop as a server, and plug my desktop into the laptop, so they both have internet without my having to buy a router? (I realize routers are as cheap as $30.) Both computers run Windows XP Pro SP3. (I also have an 10/100 Etherjet Cardbus card (PC Card)). Thanks.

  Read the article

• How to add network printer remotely without knowing the IP?

  - by Steve

  Assume your friend from over 100km away asked you to add a network printer to his computer since you're so tech savvy. How would you add network printer remotely in this case? You would need: 0. Remote connection to your friend's computer 1. Printer IP and brand/model names 2. Respective drivers downloaded either from manufacturer's website or Windows Update driver Question is, how would you find out the IP address of the printer without bothering your friend too much with technical steps? Since your friend isn't as tech savvy as you - they wouldn't know which buttons to press to get IP address.

  Read the article

• Why do I have inconsistent network issues with my laptop's wireless?

  - by Jason

  I'm having trouble with my laptop Internet connection. It's patchy at best and resets or freezes a lot. The signal strength is also random. I thought it might be a driver issue but now I don't know. Three other computers using the same wireless network run well. I've switched out wireless routers so I don't think it's the router. I thought it might be the laptop's internal wireless card but I just bought an external USB network card and I'm still having problems. Specs Lenovo T-60p Windows 7 Ultimate Edition Patches/drivers are up to date I only use one of the below at a time, disabling the other: Intel PRO/Wireless 3945ABG v. 13.3.0.137 (Internal wireless) Medialink Wireless-N USB 2.0 Adapter (USB wireless) Any ideas on what might be the problem?

  Read the article

• Total network data sent/received of a non-daemon Linux process?

  - by leden

  I'm looking for a simple and effective way of measuring total bytes received/sent from a single process upon its termination. Basically, I am looking for a tool which has the interface similar to "time" and "/usr/bin/time", e.g. measure-net-data <prog_to_run> <prog_args> Received (b): XYZ Sent (b): ABC I know that there are many tools for bandwidth/network monitoring, but as far I can tell all of them are performing the measurements it real-time, which is inappropriate not only because of overhead but also because of the inconvenience - I would need to stop the program, capture the output of the tool and then kill it. I have seen that newer versions of Linux 2.6.20+ provide /proc/<pid>/io/ which contain the information I'm looking for; however, everything under /proc/<pid> when the process terminates, so I'm again back to the same problem as with any network monitoring tool.

  Read the article

< Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >