Search Results

Search found 21717 results on 869 pages for 'setup versions'.

Page 37/869 | < Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >

  • Connection refused in ssh tunnel to apache forward proxy setup

    - by arkascha
    I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

    Read the article

  • My computer resets when i try to install Windows 7 (USB/DVD)

    - by Ranhiru
    I had a troublesome software starting up when Windows 7 was starting and i had no way to remove it because i couldn't log in to Windows. Not even safe mode. But i used Hiren's Boot CD to edit the registry to stop that software from starting up... But my efforts were not useful as Windows kept on going to an ultimate freeze just before the login screen should have been shown. And just freezes and I cannot do anything. So i decided heck with it and i now want to format the disk and reinstall a fresh copy of Windows 7. But now regardless of USB or DVD i use to boot the setup, it loads fine till you see the animating Windows and it just resets the laptop! Just plain resets! Hiren's Boot CD and Mini XP, strange enough but still works :( Any ideas what might be causing the laptop to reset in Windows 7 setup?

    Read the article

  • Recovering drive via boot to Win7 setup command prompt

    - by Valamas
    I am trying to recover data from two old IDE drives. Drive1 has been successful, but something is wrong with Drive2. It does not appear as a drive letter. Due to limited legacy hardware, the only way i can see these drives is to boot using windows 7 setup and goto the command prompt. Without going further as to why, my question is how i can access the data in this command prompt. I discovered DISKPART command and while a first time user, it looked like something that can fix my problem. Here are the results of my diskpart commands. At the bottom is a image of the commands taken with a camera. The Drive2 is present because when using the diskpart command, I can see it. How can I copy the information using a robocopy script if the drive letter is not available? how can I assign a drive letter? Is there any repair command I need to execute? When i execute DISKPART, the following is what i see. DISKPART> LIST DISK Disk### Status Size Free Disk 5 Online 37 GB 2048 KB So then I select disk 5. DISKPART> SELECT DISK 5 "Disk 5 is now the selected disk" When I list partition DISKPART> LIST PARTITION Partition ### Type Size Partition 1 Primary 101 MB Partition 2 Primary 37 GB So I select partition 2 "Partition 2 is now the selected partition." I then try to assign a drive letter DISKPART> ASSIGN LETTER=G "There is no volume specified." "Please select a volume and try again." When i list volume the drive is not present. DISKPART> LIST VOLUME Result of the above commands

    Read the article

  • First time setting up a MySQL database.

    - by Wilduck
    In trying to learn how to work with the LAMP stack, I've hit a wall with MySQL. I can't seem to find a good reference for the first time setup of MySQL to be used with Apache and python. So, my question is four-fold: 1) Under what circumstances should I create my first database. That is, what user do I use (Apache's http user? root?) 2)How do permissions work? 3) Do I have to do anything on the MySQL side to make MySQL talk to Apache, or MySQL to talk to Python/Django? 4) Is there a good resource online that describes setting all of this up? I've found a bunch for using a database once it's in place, but none for the initial setup? Notes: I'm trying to run my LAMP stack on a dedicated little box for testing/learning purposes only, so I don't have access to any DBA that could help me, as much as I'd like one.

    Read the article

  • Setup Firefox to save .pages as .zip automatically

    - by Mike Dtrick
    What do I want to do? I would like Firefox to save files with the .pages extension as .zip files automatically. Scenario You are browsing through your emails and you notice your friend just sent you an email with a file attached (a .pages in this example). Unfortunately, you have a laptop that runs Windows. Your friend continues to send tons of emails with .pages files attached and you are tired of manually saving the files as a .zip file. Ultimately, you would like Firefox to be set up so that the download/file manager recognizes the .pages extension and automatically converts it to a .zip file. What have I done? I have saved files manually by selecting save as "All Files" and setting the extension to .zip. I've gone through Firefox and their documentation and have not found anything on how to complete this task. Why am I doing this? To save time (only a few seconds, not the main reason). I would like to setup a simple solution that "converts" a file automatically without having to recall steps on how to achieve the task manually (for clients who aren't exactly tech savvy). So that clients with Windows can access the files. IMPORTANT NOTE: I am not trying to save the web page, rather an Apple document equivalent to Microsoft Word. UPDATE: The really easy method would be to save one file, right click it, choose properties and open all .pages files up with WinRAR (or any other program that extracts files from a compressed folder). For the sake of learning, I am going to "neglect" this method and continue to do some research on Firefox add-ons. I would still like to have Firefox or the download manager to do the bulk of the work for converting the file.

    Read the article

  • Multi monitor setup with a tv as well?

    - by jasondavis
    I have always had a dual monitor setup for my pc's for years now. I am now in the market to build a new PC and get some new stuff. I need some help or advice on how to run 3 monitors WITH a 4th display which will be a lcd/plasma tv. So I am thinking I can get 2 video cards and that will give me all the hookups to run 3 monitors instead of 2. I will mount all 3 monitors in a row side by side and above them on the wall I would like to mount a larger 30-40+ inch lcd or plasma tv. I would then like to hook up my atelite/cable to this tv just as I would normally hook up a tv but I would like to also be able to have an option to view my PC o this tv as well. I know that is possible but would it be possible to view my PC on that tv and also still view my 3 other monitors and have the TV be a 4th display, where I could dock a different app/window in windows in all 4 displays (3 monitors + tv) ?? Please tell me any tips/advice on how to do this including what cables/software if any/converters/ you name it. Thanks for any help

    Read the article

  • Setup proxy with Apache 2.4 on Mac 10.8

    - by Aptos
    I have 1 application (Java) that running on my local machine (localhost:9000). I want to setup Apache as a front end proxy thus I used following configuration in the httpd.conf: <Directory /> #Options FollowSymLinks Options Indexes FollowSymLinks Includes ExecCGI AllowOverride All Order deny,allow Allow from all </Directory> Listen 57173 LoadModule proxy_module modules/mod_proxy.so <VirtualHost *:9999> ProxyPreserveHost On ServerName project.play ProxyPass / http://127.0.0.1:9000/Login ProxyPassReverse / http://127.0.0.1:9000/Login LogLevel debug </VirtualHost> ServerName localhost:57173 I change my vim /private/etc/hosts to: ## # Host Database # # localhost is used to configure the loopback interface # when the system is booting. Do not change this entry. ## 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost 127.0.0.1:9999 project.play and use dscacheutil -flushcache. The problem is that I can only access to localhost:57173, when I tried accessing http://project.play:9999, Chrome returns "Oops! Google Chrome could not find project.play:9999". Can somebody show me where I were wrong? Thank you very much P/S: When accessing localhost:9999 it returns The server made a boo boo.

    Read the article

  • Proper web server setup

    - by DMin
    I just got myself a slicehost basic slice to play around with so I can learn how to setup web-servers. I have Ubuntu 10.04.2 installed on the server. I was able to successfully get the server up and running from scratch, these were the things I did - following this tutorial. I know this is probably just a starters tutorial, so, I was wondering if you guys can tell me what you like to do while setting up production servers. These are the steps that were followed : Update and Upgrade Ubuntu sudo apt-get install apache2 php5-mysql libapache2-mod-php5 mysql-server Backup a copy of and edit apache2.conf Set : 'ServerTokens Full' to 'ServerTokens Prod''ServerSignature On' to 'ServerSignature Off' Backup php.ini and then Change “expose_php = On” to “expose_php = Off” Restart Apache Install Shorewall firewall Configure Shorewall to only accept HTTP and SSH connections(in the rules file) Enable shorewall on startup Add the website to the server : sudo usermod -g www-data root sudo chown -R www-data:www-data /var/www sudo chmod -R 775 /var/www I want make this CommunityWiki but can't seem to find the option to do it. Please feel free to add any feedback on the processes and things I am doing right/wrong. Much appriciated, thanks! :)

    Read the article

  • how to setup a bridge with 2 NICs and few virtual machines

    - by Bond
    Here is my situation. I have a server with 2 NICs. I have installed virtual box and I have created a few Guest Operating Systems on it. I want these Virtual Machines to be using a bridge.NIC2 would be used to setup this bridge and NIC1 would be connected to corporate network.I am not clear with how should I go on doing this. /etc/network/interfaces is the file which I am trying to modify etc. My approach is following 1) Define a configuration file /etc/network/interfaces 2) Create IPTABLES as how NIC1 will forward the packets to Bridge on NIC2 Now comes the problem I do not understand what is the meaning of following lines in the configuration file auto lo iface lo inet loopback # The primary network interface auto eth2 iface eth2 inet manual auto br0 iface br0 inet static address 192.168.1.14 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.10 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 192.168.13.2 dns-search myserver.net bridge_ports eth2 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off So any pointers to what should be the entries of /etc/network/interfaces file. So that I understand which parameter is to be used when and where that would help me.

    Read the article

  • Windows 7 64 bit Installation freezes after a while durig the setup

    - by vinz243
    I have a windows 7 32 bits on my computer. Because i have 5 gb of ram (kingston) on my asus M2N motherboard and only 3 were able to be used, I bought W7 x64 and install it. It loads the wizard, but after a while, it freezes, and I have to force reboot. It first crashed while unzipping w7 files, but if I wait a while on the terms page for example, it can crash before, which make me think that it is a matter of time. I remember I had the same issue while booting on Ubuntu x64, it crashed randomly but not load completely. No bip or other messages. Configuration: Software OS (before) W7 x86 Pro New OS : W7 x64 Pro Antivirus : avast (bios verification ?) BIOS 03/27/2008 - v08.00.12 Hardware : Motherboard : Asus M2N Processor : AMD Athlon 64 dualcore @ 2.6 GHZ Memory : 5120 MB ((2 + 2) + (1)) NOTES : I ran a memory test using openSUSE cd, though i have not finished it, it ran. EDIT: I tried not to run the setup but wait, and i get the BSOD : A problem... TL;DW IRQL_NOT_LESS_OR_EQUAL If it is.. TL;DW ***STOP: 0x0000000A (0x0000000000000000,0x0000000000000002, 0x0000000000000001, 0xFFFFF8001A49ED1F)

    Read the article

  • Struggling with proper way to setup Permissions on Linux/Apache Web Server

    - by Dr. DOT
    Your expert experience and assistance is great, greatly appreciated here. I have been running a LAMP server for a long time, yet I still struggle with the best way to set file & directory permissions for FTP and WWW protocol activity. My Control panel is WHM/cPanel (not that it makes a difference), and out-of-the box: files are owned by the user account setup in WHM (eg, "abc") files have a group setting of "abc" as well file permissions are created with 644 directories are owned by "abc" directories have a group setting of "abc" directories permissions are created with 0755 Again, these are the default permission settings. Now everything is fine with FTP activity, but please advise me if any of these file/directory settings create issues, especially with security. Here's where my struggle comes into play. I have PHP apps that allow a visitor to create, edit, rename, delete, etc. sub-directories and files in certain selected directories. PHP runs as "nobody" on my server. So in order to get my PHP/Web apps to work, I have had to: chown nobody * chgrp nobody * chmod 0777 * to everything in these certain & selected sub-directories. I know this is probably a huge security whole (so don't ask me for any links :) but how should I set all the permissions to allow my FTP user to do his thing while allowing the PHP apps to do their thing will also "minimizing" any security risks and exposures? I know that big CMS systems like Drupal, Joomla, WordPress and so on, handle this. Thanks ahead of time for reading through this and offering your expert advice!

    Read the article

  • How to setup port forwarding from my Webserver (apache) to my Database server (mysql)

    - by karman888
    Hello again guys, and thank you for your help so far. Here is my problem: I have two remote dedicated servers, one webserver that runs apache, and one db server that runs mysql. The apache server is visible on the internet of course, but the second server is only visible to the apache server because they are connected with LAN. I need to connect to the remote mysql server through internet from my home-pc , but only apache server is visible to my home-pc. How can i setup port-forwarding from my apache server to the mysql server so i will be able to "see" the mysql server from my home-pc? This question is a follow-up from my first question Connect to remote mysql server from my application. Problem is that Mysql server is on LAN in which you answered me and helped me a lot by telling me to do "port-forwarding". I looked over the internet, and i cant find a good how-to to do port-forwarding. I'm an experienced programmer, but have little experience on hardware and networks. I can understand though what must be done, so i just need a litle help to sort things out :) I hope you can help me guys, Thank you in advance p.s. machine that Apache is running is on CentOS, mysql server also CentOS. p.s2 webserver runs WebHostManager i dont know if that makes any difference or it can be made easily through this, i just mention it :)

    Read the article

  • esx5 debian VM vlan setup

    - by Kstro21
    i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 2 to 14 stp disable ntdp enable ndp enable bpdu enable then, i created a standar switch(sw1) using the vSphere Client, the VLAN ID is set to All (4095), i also created a VM with Debian 6, with a NIC connected to sw1, now, i want to configure this NIC for a selected group of vlans auto vlan10 iface vlan10 inet static address 11.10.1.0 netmask 255.255.255.224 mtu 1500 vlan_raw_device eth0 auto vlan14 iface vlan14 inet static address 11.10.1.65 netmask 255.255.255.248 mtu 1500 vlan_raw_device eth0 so, when i restart the network using /etc/init.d/networking restart, i got this error Reconfiguring network interfaces...SIOCSIFADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFMTU: No such device vlan14: ERROR while getting interface flags: No such device Failed to bring up vlan14. done. this is just part of the error, so, my questions is: is this possible?, i mean, what i'm trying to achieve using ESX Virtual Machines, VLANS, etc is this a Debian problem? can be solved? i've read about a file named z25_persistent-net.rules in Debian but it doesn't exist in my installation. in the In the vSphere Networking for ESX5 guide, you can read: If you enter 0 or leave the option blank, the port group can see only untagged (non-VLAN) traffic. If you enter 4095, the port group can see traffic on any VLAN while leaving the VLAN tags intact. So, in theory, it should work, right? Hope you can help me up with this one Thanks

    Read the article

  • Setup windows 2012 AD in Hyper-V for a Test environment

    - by hub
    Im trying to setup a Windos 2012 R2 test environment on my work computer (a laptop). I have a AD, DHCP and DNS server on server A, and a client connecting to the doman and that works. The client can ping the AD server and gets a valid IP adress. If I ping google.com from the client I get the IP adress but I dont get any responses (request time out). If i ping google.com from server A it works as it should. Server A have a connection to the Internet through a "external network switch" in hyper-v, which gets its internet from a router and the client is connected to a "internal network switch". May the poblem be that server A is behind a router? Can I make this solution to work regadless the network my laptop is connected to? At home i have one IP adress, at work its a totally different range. What I would like is to use my laptops internet connection, regardless wifi or wired, to act as incomming internet, is this possible?

    Read the article

  • CentOS 6.5 x64 + Ajendi +nginx + php-fpm + mysql setup unable to load the PHP page

    - by Francis
    I'm using Ajendi to setup a PHP web server, I can load the PHP info page, when I try to load the PHP copy from other server, I get a blank page with this log appear on access log, I have no clue what was wrong and troubleshoot further, please advice. x.x.x.x - - [28/May/2014:10:08:37 -0400] "GET /index.php HTTP/1.1" 200 31 "-" "Mozilla/5.0 (Windows NT 6.1; rv:29.0) Gecko/20100101 Firefox/29.0" 2.6.32-431.1.2.0.1.el6.x86_64 cat /etc/redhat-release CentOS release 6.5 (Final) The vhost config AUTOMATICALLY GENERATED - DO NO EDIT! server { listen *:80; server_name test.com www.test.com; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; root /www; index index.html index.htm index.php; location ~ \.php$ { alias /www; fastcgi_index index.php; include fcgi.conf; fastcgi_pass unix:/var/run/php-fcgi-php-fcgi-0.sock; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } }

    Read the article

  • How to setup Joomla CMS as a backend for iPhone app

    - by srik
    I would like my iPhone app to get dynamic content off the net. This content should be managed using a CMS. I have gone ahead and installed Joomla on my server and will be using the Joomla web interface to create and manage content. I would now like the iPhone app to login to my server and fetch the content. I do not want the complete web pages for my iPhone app. Instead, I want the content in the form of XML or JSON or some serialized format so that I can use the data in a custom layout native to the app. So I am looking for 2 things in particular: 1. How to setup HTTP based authentication for my iPhone app to access data from my server. 2. How to access the content in a serialized format (XML, JSON etc) Are there plugins/extensions/components I can use to achieve the same. Any advice on how this can be achieved would be helpful. I am completely new to setting up/using CMS.

    Read the article

  • How to setup Joomla CMS as a backend for iPhone app

    - by srik
    I would like my iPhone app to get dynamic content off the net. This content should be managed using a CMS. I have gone ahead and installed Joomla on my server and will be using the Joomla web interface to create and manage content. I would now like the iPhone app to login to my server and fetch the content. I do not want the complete web pages for my iPhone app. Instead, I want the content in the form of XML or JSON or some serialized format so that I can use the data in a custom layout native to the app. So I am looking for 2 things in particular: 1. How to setup HTTP based authentication for my iPhone app to access data from my server. 2. How to access the content in a serialized format (XML, JSON etc) Are there plugins/extensions/components I can use to achieve the same. Any advice on how this can be achieved would be helpful. I am completely new to setting up/using CMS.

    Read the article

  • Computer hangs at BIOS screen. Cannot enter setup

    - by d2jxp
    I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

    Read the article

  • Server installation logging / logbook / diary?

    - by The MYYN
    Are there some ways field-tested ways to keep a kind of logbook for a server? Including: software installations (and de-installations) custom configurations (e.g. of a webserver, ssh daemon, etc.) personal notes The big picture. I am preparing a server and would like to extensively document the state and how it was established over time, so that a new person can easily see, what's going on and why. The setup is not too complicated, but I would like to do it anyway. I once used something like Maintain /etc with mercurial on Debian and it was nice, but I am looking for a little more flexible solution. Addendum: So I am interested in logging and documentation first. In an ideal world however, I would like to have a command, which in a few steps would take me from a bare newly installed unix system to a functional environment with all the components setup and in place by the means of, say an 'executable' log. But that would be very ideal, I imagine.

    Read the article

  • Reverse NAT Setup for Hyper-V on Win 2008 R2

    - by sukru
    I'm trying to setup a Linux server behind a Windows Hyper-V host that will help supply some of the services (SSH, HTTPS, etc). However getting RRAS configured for reverse NAT (port forwarding) turned out to be a non trivial task. As a staring point, I tried forwarding port 22 (SSH) to the virtual machine. The virtual machine is on a public interface (i.e.: it also has a visible IP on the same network as the host). On RRAS management console I tried to add a rule, by adding "Local Area Connection" to NAT pool (Public Interface - Enable Nat), and an incoming rule for port 22 - :22. I also tried with the same port enabled on Windows Firewall (and not). The NAT management page tells there are "1 mappings" and "30+ Outbound packets transleted". However all other counters (Inbound packets translated, and respective rejected ones) are always zero. (I'm trying to access the server from an external machine). I can directly access the service if I give the VM's public IP, but not the host's one. Is there a way to enable this on RRAS?

    Read the article

  • Winodws server 2003 Setup

    - by Barracksbuilder
    I work at a university maintaining the computer science department server. I am looking for a more economical way to stream line the set up of student accounts. CS students are granted a Username and password an IIS virtual directory, FTP virtual directory, and a mysql database. Server is running windows server 2003R2 (Possibly migrating to 2008R2) The server is running a domain though no students physically log a terminal into it (No computers are part of my domain.) Creating the account is a manual process. I did right a PHP script to query the Universities AD and copy the information and write it to my AD. I then have to create basically the users home directory. I tried having AD do it but since the user never physically logs in it never creates the directory. Permissions on this folder are set to User - full, Instructors (group) - full, Users (group) - read, IUSER - read. Inside of the users folder their is a "Private" folder with permissions User - full, instructors (group) - full. Next step is IIS I create a virtual directory in the default web site pointed to the users home directory so they have a website. Same goes for FTP virtual directory in the default ftp configuration to allow the users to upload files to their website. Mysql I have to create a user and password then create a mysql scheme (database) full access for the user and full access to the instructors account to be able to access the students database. All of this is done manually and takes me a week to do. The closest description is maybe a shared hosting environment. Is there a better way to do this? Scripting wise, or better structure setup?

    Read the article

  • iPhone & iPad versions of same app?

    - by 4thSpace
    I have an iPhone app and would like to create iPad version of it. What is the best way to setup the project when you want an iPhone and iPad version of the app? I don't see that I'm able to use the same code base since the iPad version will have features in it that the iPhone version doesn't. It seems as though maintenance is going to go up with two similar code bases for the same app.

    Read the article

  • Mixing .NET versions between website and virtual directories and the "server application unavailable" error Message

    - by Doug Chamberlain
    Backstory Last month our development team created a new asp.net 3.5 application to place out on our production website. Once we had the work completed, we requested from the group that manages are server to copy the app out to our production site, and configure the virtual directory as a new application. On 12/27/2010, two public 'Gineau Pigs' were selected to use the app, and it worked great. On 12/30/2010, We received notification by internal staff, that when that staff member tried to access the application (this was the Business Process Owner) they recieved the 'Server Application Unavailable' message. When I called the group that does our server support, I was told that it probably failed, because I didn't close the connections in my code. However, the same group went in and then created a separate app pool for this Extension Request application. It has had no issues since. I did a little googling, since I do not like being blamed for things. I found that the 'Server Application Unavailable' message will also appear when you have multiple applications using different frameworks and you do not put them in different application pools. Technical Details - Tree of our website structure Main Website <-- ASP Classic +-Virtual Directory(ExtensionRequest) <-- ASP 3.5 From our server support group: 'Reviewed server logs and website setup in IIS. Had to reset the application pool as it was not working properly. This corrected the website and it is now back online. We went ahead and created a application pool for the extension web so it is isolated from the main site pool. In the past we have seen other application do this when there is a connection being left open and the pool fills up. Would recommend reviewing site code to make sure no connections are being left open.' The Real Question: What really caused the failure? Isn't the connection being left open issue an ASP Classic issue? Wouldn't the ExtensionRequest application have to be used (more than twice) in the first place to have the connections left open? Is it more likely the failure is caused by them not bothering to setup the new Application in it's own App Pool in the first place? Sorry for the long windedness

    Read the article

  • iPhone SDK 3.2 beta and iPhone SDK 3.1.2

    - by pratik
    Hello, Currently I am using iPhone SDK 3.1.2 for developing iPhone apps. Apple has recently released iPhone SDK 3.2 beta and I want to try my hands with it. But my problem is that I want to use both versions of SDKs, 3.1.2 since I am currently developing apps and uploading on app store, 3.2 beta to start trying the new version (but Apple will not accept apps on App Store, if developed using 3.2 beta) Please guide me. Regards, Pratik

    Read the article

  • Compile Delphi component package (bpl) for different Delphi versions

    - by FractalizeR
    Hello. The situation is the following. Typically I use RAD Studio 2010 for Delphi development. I have some components I would like to redistribute in binary form (*.bpl without source). But I would like people to be able to use them despite of their Delphi version. But, for example, dcu files can be used only by compiler version, which generated them. Almost the same situation is with bpl files as I know. Every bpl file will require corresponding VCLXX.bpl library depending on Delphi version. How do I make my bpls, compiled in 2010 to be able to be used in Delphi7, 2007 etc? Is the only solution to have ALL Delphi versions installed and compile bpl files separately in each?

    Read the article

< Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >