Search Results

Search found 11188 results on 448 pages for 'django manage py'.

Page 370/448 | < Previous Page | 366 367 368 369 370 371 372 373 374 375 376 377  | Next Page >

  • What's hogging my CPU?

    - by endolith
    Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. I try killing lots of things, but it continues at 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, that normally only hits 100% CPU when I'm doing something that requires it (like loading 32 Firefox tabs) after which it goes back to a normal idle level. It's not a new install or anything. It shouldn't be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing any process I saw active again, and killing vino-server finally fixed the problem, even though it never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). How did it manage to use 100% CPU while top only showed it as 5% or so? How do I identify the culprit in the future? Looks like I'm not the only one: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

    Read the article

  • MySQL is killing the server IO.

    - by OneOfOne
    I manage a fairly large/busy vBulletin forums (running on gigenet cloud), the database is ~ 10 GB (~9 milion posts, ~60 queries per second), lately MySQL have been grinding the disk like there's no tomorrow according to iotop and slowing the site. The last idea I can think of is using replication, but I'm not sure how much that would help and worried about database sync. I'm out of ideas, any tips on how to improve the situation would be highly appreciated. Specs : Debian Lenny 64bit ~12Ghz (6x2GHz) CPU, 7520gb RAM, 160gb disk. Kernel : 2.6.32-4-amd64 mysqld Ver 5.1.54-0.dotdeb.0 for debian-linux-gnu on x86_64 ((Debian)) Other software: vBulletin 3.8.4 memcached 1.2.2 PHP 5.3.5-0.dotdeb.0 (fpm-fcgi) (built: Jan 7 2011 00:07:27) lighttpd/1.4.28 (ssl) - a light and fast webserver PHP and vBulletin are configured to use memcached. MySQL Settings : [mysqld] key_buffer = 128M max_allowed_packet = 16M thread_cache_size = 8 myisam-recover = BACKUP max_connections = 1024 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M key_buffer_size = 128M join_buffer_size = 8M tmp_table_size = 16M max_heap_table_size = 16M table_cache = 96 Other : From the cloud's IO chart, we're averaging 100mb/s read. > vmstat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 9 0 73140 36336 8968 1859160 0 0 42 15 3 2 6 1 89 5 > /etc/init.d/mysql status Threads: 49 Questions: 252139 Slow queries: 164 Opens: 53573 Flush tables: 1 Open tables: 337 Queries per second avg: 61.302. moved from superuser

    Read the article

  • SOGo installation on Mail Server

    - by i.h4d35
    We run a normal mail server on cPanel for web-based email. We've just got a request to add Calendar, address book, tasks functions; mobile capabilities (I'm guessing acces via a mobile client/app); public folders etc. On the client-side, we have some people using webmail, some use MS Outlook and some others use Mozilla Thunderbird. Having looked around, I zeroed in on SOGo, Citadel and kolab as options for this. I read through SOGo's official install guide and also checked here and here. However, I see most of the HowTo's ask installation of MySQL/PgSQL, LDAP, Samba etc. While I can manage installation of Samba (if required), I have no idea if installing LDAP, MySQL etc is really required. Also, any guidance as to how to install on a regular mail server would be appreciated. Sorry if this sounds vague. If any more information is required, I'll be happy to give it. Thanks in advance. Edit: This server in question has always been governed via cPanel (to install PHP, MySQL, configure DNS etc). So I am confused if really need LDAP.

    Read the article

  • Getting Server 2008 R2 to ignore all traffic from Internet-facing NIC, leaving it to a VM

    - by Wolvenmoon
    I got in to Server 2008 R2 via Dreamspark and would like to start learning on it. I don't have much option but to put it on a system sitting between the Internet and my home LAN due to electricity bills and the fact that 3 computers in an 11x11 space in 102 degree weather is pretty stygian. Currently I use a ClearOS gateway to manage everything, what I'd like to do is take my server 2008 R2 box, which has two NICs, and drop it at the head of my network. I'd want Server 2008 R2 to ignore all traffic on the external facing NIC and pass it to a virtual ClearOS gateway, and to put all its Internet traffic through its other NIC - which will face the rest of my network and be the default gateway for it. The theory is to keep the potentially vulnerable Server 2008 R2 install as tucked behind a Linux box as possible, without sacrificing too much performance. This is a home network that occasionally hosts dedicated game servers and voice chat servers, so most malicious activity is in the form of drive by non-targeted attacks, however, I don't trust Windows Server because I don't know the OS well enough, yet. So, three questions: How do I do this, am I going to be reasonably more secure doing this than if I just let the Server 2008 R2 rig handle all the network traffic and DHCP (not an option), and should I virtualize the Server 2008 R2 rig instead and if so in what? (Core 2 Duo e6600 w/ 5 gigs usable RAM)

    Read the article

  • Can IIS (Ideally Azure) do SSL Proxying?

    - by Acoustic
    My team has been asked to add a new feature to a project we're working on, and none of can find authoritative details on whether it's possible with Windows/IIS. The short of it is that we're hoping to have customers update their DNS with a CNAME record to point their website to our server instead of theirs (they why's are trivial - it's what the app does on behalf of your site). We're using a reverse proxy with several custom modules to serve particular content from the original servers. So far everything works perfectly until we encounter SSL. Is there a way to have IIS serve up an SSL certificate from another server? In other words, is there a way to be a trusted man in the middle? I'm hoping that's possible so that we don't have to require all our clients to re-issue their SSL certs. Frankly, we don't want to have to manage hundreds of certs. I'd also like to avoid a UCC situation if there's a way to because it seems to require re-creating the cert each time a client is added. So, any pointers on proxying/hosting SSL (or even dynamic SSL hosting like http://www.globalsign.com/cloud/) would be appreciated.

    Read the article

  • How do I use .htaccess conditional redirects for multiple domains?

    - by John
    I'm managing about 15 or so domains for a particular promotion. Each domain has specific redirects in place, as shown below. Rather than make 15 different .htaccess files that I would later have to manage separately, I'd like to use a single .htaccess file and use a symbolic link into each website's directory. The trouble is that, I can't figure out how to make the rules apply only for a specific domain. Every time I visit www.redirectsite2.com, it sends me to www.targetsite.com/search.html?state=PA&id=75, when it should instead be sending me to www.targetsite.com/search.html?state=NJ&id=68. How exactly do I make multiple RewriteRules apply for a given domain and only that domain? Is this even possible to do within a single .htaccess file? Options +FollowSymlinks # redirectsite1.com RewriteEngine On RewriteBase / # start processing rules for www.redirectsite1.com RewriteCond %{QUERY_STRING} ^$ RewriteCond %{HTTP_HOST} ^www\.redirectsite1\.com$ # rule for organic visit first RewriteRule ^$ http://targetsite.com/search.html?state=PA&id=75 [QSA,R,L] RewriteRule ^PGN$ http://targetsite.com/search.html?state=PA&id=26 [QSA,R,NC,L] RewriteRule ^NS$ http://targetsite.com/search.html?state=PA&id=27 [QSA,R,NC,L] RewriteRule ^INQ$ http://targetsite.com/search.html?state=PA&id=28 [QSA,R,NC,L] RewriteRule ^AA$ http://targetsite.com/search.html?state=PA&id=29 [QSA,R,NC,L] RewriteRule ^PI$ http://targetsite.com/search.html?state=PA&id=30 [QSA,R,NC,L] RewriteRule ^GV$ http://targetsite.com/search.html?state=PA&id=31 [QSA,R,NC,L] # catch-all rule, using the same id as the organic visit RewriteRule ^([a-z]+)?$ http://targetsite.com/search.html?state=PA&id=75 [QSA,R,NC,L] # end processing rules for www.redirectsite1.com # begin rules for redirectsite2.com RewriteCond %{QUERY_STRING} ^$ RewriteCond %{HTTP_HOST} ^www\.redirectsite2\.com$ # rule for organic visit first RewriteRule ^$ http://targetsite.com/search.html?state=NJ&id=68 [QSA,R,L] RewriteRule ^SL$ http://targetsite.com/search.html?state=NJ&id=6 [QSA,R,NC,L] RewriteRule ^APP$ http://targetsite.com/search.html?state=NJ&id=8 [QSA,R,NC,L] # catch-all rule, using the same id as the organic visit RewriteRule ^([a-z]+)?$ http://targetsite.com/search.html?state=NJ&id=68 [QSA,R,NC,L] Thanks for any help you may be able to provide!

    Read the article

  • redirect from mysite.com to www.mysite.com

    - by jml
    hi there, i know that this has been answered many many times, so if someone wants to point me to another thread that answers my question specifically, that is fine... for right now, my searches aren't yielding many results. so i have a website like mysite.com that has a flash swf embedded in it and i go to www.mysite.com ... all of the sudden, things don't work properly. i would like to get to the bottom of this, because it's not like the page just "doesn't load" at all; it loads and i can only do certain things; as if certain functionality is disabled (might be url requests for specific urls etc). do i need to manage this in my control panel? i wouldn't assume so, because the site loads; just has a crippled functionality from within the swf. i was thinking it might have more to do with my crossdomain.xml file; could this be the case? thanks for any tips or suggestions.

    Read the article

  • Windows file locks allowing multiple users to write to open file over network

    - by JPbuntu
    I have 6 windows computers (xp,vista,7) that need to access a samba share (Ubuntu 12.04). I am trying to make it so only one client can open a file at a given time. I thought this was pretty standard behavior of file locks, but I can't get it to work. The way it is right now a file can be open by two users, and changed and saved by either one of them. The last file saved overwrites what ever changes the other user made. At first I thought this was a Samba configuration problem, but I get this behavior even between two windows machines. So far I have only tested: Windows Xp Windows Vista Windows XP Samba << Windows Vista and both give the same behavior. When I tested the Samba configuration, I had set strict locking = yes and get errors logged like this: close_remove_share_mode: Could not get share mode lock for file _prod/part_number_list_COPY.xlsx Eventually all of the files are going to be moved onto the Samba share, so that is the configuration I am most concerned about fixing. Any ideas? Thanks in advance. EDIT: I tested an excel file again, and it is now working properly in both above mentioned cases, I am also no longer getting the above mentioned error. I don't know what happened, perhaps a restart fixed it? (also works with strict locking = no) Although I still need to find a solution for the CAD/CAM files we use, the software is Vector and it does not seem to be using file locks. Is there any software that I can use to manage these files, so two people can't open/edit them at a time? Maybe a windows application that forces file locks? Or a dirt simple version control system? (the only ones I have seen at are too complicated for our needs).

    Read the article

  • Is one server on a vlan unnecessary?

    - by moomoochoo
    DETAILS I've been researching web hosting solutions in Japan. Based on this question one of the services available seems to be a VLAN. I've read about the advantages of such a system for a large organization, but there doesn't seem to be much information regarding smaller setups. I take that to mean that for one server it is likely to be unnecessary? My concern is that I don't know how many other servers are on the WAN, so regardless of how many servers I use a VLAN might still be a good idea. SERVER INFO One dedicated server would be used. It would not be virtualized. My Research so far Based on comments here, a VLAN would be useful for mitigating these problems. A user on another server could, either mistakenly or maliciously, assign one of your IP addresses to their server, resulting in a "duplicate IP" situation that would cause connectivity issues. A user on another server could poison the arp cache and potentially redirect traffic to snoop on communication intended to/from your server. (later in the discussion this point was said to be unrealistic.) QUESTION Is it worthwhile getting a vlan for one dedicated server? Will it be easier/the same/ harder to manage?

    Read the article

  • "Run As Administrator" on program right click failing and not launching program

    - by GONeale
    This problem lies within a relatively fresh x64 Windows 7 install ~4 weeks, but is also a problem I have seen on Windows Vista machines (x86 versions). Since the other day, any programs attempted to be launched via right clicking on a shortcut (.lnk)'s context menu and pressing - "Run As Administrator" for instance, in the Quick Launch/Jump List in Windows 7 has failed, screen has not dimmed, no UAC popup. In fact the program does not even load. There is no way around this unless I use the shortcut version from "All Programs" which appears to work, very strange? I have performed no major software installs, nothing out of the ordinary. Has anybody encountered this or know what would be causing it? Here's an example of somebody else experiencing this problem in Vista with no solution: http://www.vistax64.com/vista-general/131918-strange-run-administrator-problem.html and I believe this problem is related, I also cannot right click - "Manage" on my computer): http://windows7forums.com/windows-7-support/5501-run-administrator-broken.html I am running the latest version of Avira AntiVir Virus Scanner and pretty concious of what I download, I don't think it is a virus, nor do I believe it is due to the RC Version of Windows 7, because I have seen the problem across multiple Operating Systems versions. Thanks guys.

    Read the article

  • Windows 7 deployment thru WDS

    - by vn
    Hello, I am deploying new systems on my network and I built my reference computer by installing the OS the manufacturers (Dell and a custom built system from some local business) gave with all drivers, installed all the desired applications. As for the settings part, I'm doing most of it thru GPOs. I want to image my reference computer and deploy it with WDS. i found several links on how to sysprep, but they're all doing it with some differences without explaining them. My questions : How do I manage (into sysprep) the domain join/computer naming part since (from what I understand) WDS manages that? How do I know/determine what I need to setup into my sysprep.xml? Can you sysprep a first time, try and if it fails, do some modifications and try again? I am thinking of doing a basis sysprep, checking what info can be automated and correct that in the answer file. What do I miss if skipping the "audit" mode? I don't plan on re-doing the reference computer... I read that when sysprepping, it resets settings from the reference computer like the computer name, activation/key and such... what setting is sysprep resetting by default that I should be aware of? I must admit I am quite lost about Win7, sysprep, RIS, MDI toolkit, WDS.. I understand the way of doing with XP, but it changed so much with Windows 7! The links I am reading are : http://far2paranoid.wordpress.com/2007/12/05/prep-for-sysprep/ http://blog.brianleejackson.com/sysprep-a-windows-7-machine-%E2%80%93-start-to-finish-v2 http://www.ehow.com/print/how_5392616_sysprep-machine-start-finish-v2.html Thank you VERY much for any answers, they are much appreciated.

    Read the article

  • Sign multiple domains with single Domain Key (dk-filter)

    - by Lashae
    Motivation The private shopping website GILT, send periodical update emails from giltgroupe.bounce.ed10.net however all of the mails are signed with domain keys of giltgroupe.com. mailed-by giltgroupe.bounce.ed10.net signed-by giltgroupe.com My Story I couldn't manage to sign x.com with y.com 's domain key using dk-filter under Debian Lenny with postfix. If I try to init dk-filter service with following arguments: DAEMON_OPTS="$DAEMON_OPTS -d x.com,y.com -c nofws -k -i /var/dk-filter/internal_hosts -s /etc/dk-keys.conf" dk-filter service signs with domain x.com (d=x.com) If I change the daemon arg.s as following: DAEMON_OPTS="$DAEMON_OPTS -d x.com -c nofws -k -i /var/dk-filter/internal_hosts -s /etc/dk-keys.conf" then emails sent From y.com is not being signed. the dk-keys.conf file is as follows: *:/var/dk-filter/y.com/mail I managed to do same thing with DKIM, works perfect. However DK doesn't seem to work. I don't have any problem signing y.com's emails with y.com's key and x.com's emails x.com's key, which indicates there is no configuration problem. Do you have any experience/advice to make it possible to sign emails from multiple domains by a specific chosen domain?

    Read the article

  • can't access SATA card config screen on boot, nor access the disks

    - by Ronald
    We've just upgraded our file server using an ASUS P6T WS Pro board, running FreeBSD-RELEASE 8.2 and using zfs to manage 12 WD20EARS disks. Since our 3ware card has been giving us trouble we started using the six on-board SATA connectors and got a SuperMicro USAS2-L8i to provide eight more ports. Mechanically, the card is an awkward fit but electrically it all seems ok. Upon boot, the LSI controller shows up and states that pressing ctrl-c will bring up the LSI Config Utility. When doing that, the message changes to state that the utility will be started after initialization, however that never happens. There does seem to be an error message that's only displayed too briefly to read and seems to be about PCI and "not enough space". (That message is pushed off by a hardware summary and I've found no way to scroll back at this point.) The disks do not show up in any recognizable ways after booting, either. I found a hint in another discussion to check the address mapping on either the card or the motherboard BIOS, but have found no way to do that. So what I tried on a hunch is to disable everything that's on-board, including network adapters, Firewire controller and SATA. In fact, after doing that, I can successfully launch the LSI Config Utility. As far as I can tell, all looks well in there, and when booting in that configuration it also displays a list of the disks connected to it, which looks just fine as well. Only problem now is that I can't boot that way, because I need the on-board SATA controller and network adapters. As soon as I re-enable any of them I'm back to square one. That discussion I mentioned about mapping addresses said to try D000, then D7FF, then DFFF, in order. The LSI Config Utility shows the card address as D000 but offers no way of changing it. Any tips or insights would be appreciated.

    Read the article

  • PHP + MYSQL site perfomance

    - by Diego
    I have to manage a site which wasn't developed by me. It is in PHP using a mysql database, which is located in the web server. The site, sometimes (when the visitors increase too much) stops responding, or respond too slow. I have developed some sites in PHP but never took care of the management so really don't know where to start. The server (the hard) seems to be fine, when the web stops responding the cpu is being used at about 55% and has a lot of memory. I'm not asking someone to solve this issue. I only would really like if someone could give me a few tips about where can I find logs and how should I read and interpret them. So, that way I would be able to know if its the net traffic, the database (which queries), or what. Thanks! Update: Forgot to say: it is a Windows Server 2003. Note: I've recorded about a day with Jet Profiler. I don't really understand all the information it provides but there is one query which it marks as really slow. It makes sense because it is a select with a where clause which has three like condition. Initially I didn't include this in my question because when I run the query from MySQL Query Browser it doesn't take any long. It is under 0.01 seconds.

    Read the article

  • How to recover deleted NTFS partitions?

    - by Frank
    Last night I made a terrible mistake. I was reinstalling Windows and I accidentally deleted all the partitions on all my drives. I realized my mistake before I had created any partitions, so nothing has been written to any of the disks. I'm currently at my wits' end about what I'll do if I don't manage to recover the data. I have two 1TB drives and a 2TB. One of the 1TB was the drive I was supposed to be reformatting so nothing to be recovered there. I am currently in a Linux livecd. In this article http://support.microsoft.com/kb/245725 Microsoft advises to recreate the exact same partition but choose not to format it, and then recover the backup boot sector from the end of the ntfs volume. But none of the drives I want to recover are bootable drives. So does that mean I do not need to rewrite the boot sector? As in if I simply recreate a partition of the same size it will see all my data? Or would I be better off using the TestDisk utility? http://www.cgsecurity.org/wiki/TestDisk Please help, I'm desperate!!

    Read the article

  • Get Squid to pass X-Requested-With header

    - by tftd
    I have configured a squid 3.1 proxy server. Everything works great except for the X-Requested-With header. I can't manage to figure out how to pass that header to the site I'm attempting to open via the proxy. This is my current configuration: request_header_access Allow allow all request_header_access Authorization allow all request_header_access WWW-Authenticate allow all request_header_access Proxy-Authorization allow all request_header_access Proxy-Authenticate allow all request_header_access Cache-Control allow all request_header_access Content-Encoding allow all request_header_access Content-Length allow all request_header_access Content-Type allow all request_header_access Date allow all request_header_access Expires allow all request_header_access Host allow all request_header_access If-Modified-Since allow all request_header_access Last-Modified allow all request_header_access Location allow all request_header_access Pragma allow all request_header_access Accept allow all request_header_access Accept-Charset allow all request_header_access Accept-Encoding allow all request_header_access Accept-Language allow all request_header_access Content-Language allow all request_header_access Cookie allow all request_header_access Mime-Version allow all request_header_access Retry-After allow all request_header_access Title allow all request_header_access Connection allow all request_header_access User-Agent allow all request_header_access All deny all #remove all other headers # delete "x-forwarder-for.." headers forwarded_for delete request_header_access Via deny all request_header_access X-Forwarded-For deny all I tried to add this line request_header_access X-Requested-With allow all to the configuration but apparently X-Requested-With is an unknown header name... Apparently I'm missing something?

    Read the article

  • How to balance the root domain using NS records?

    - by Patrick McCurley
    I have two load balancers that balance incoming traffic across multiple data centers. These work fine. I can test them out by doing an 'nslookup mydomain.com xIP' I have now taken out DNS services with DYN.com to allow me to manage the DNS Zone file so that typing mydomain.com will ask my load balancers what the IP address is to resolve. Step 1 : the NS record for www. I set up A records (glue) for ns1 & ns2, then the corresponding NS record to delegate the DNS lookup to the balancers instead of DYN.com's nameservers. ns1.mydomain.com A [ip address of load balancer 1] ns2.mydomain.com A [ip address of load balancer 1] www.mydomain.com NS ns1.mydomain.com www.mydomain.com NS ns2.mydomain.com All is well - when I type www.mydomain.com, the requests get delegated to my load balancers who provide the IP address of the endpoint and the connect is made successfully. Step 2 : the NS record for root. This is where I run into problems. I need customers to be able to type 'mydomain.com' (without the www) and ALSO get delegated to the load balancers for the IP address. However - of the research I have done, and through the DYN control panel, it seems to be not allowed to provide an NS record for the root - as this overrides the default NS servers. How can i delegate both the root, and the www. to my load balancers?

    Read the article

  • How to prevent nginx from locking files on mounted samba partition in Centos 6

    - by Bruce Kirkpatrick
    I'm using nginx 1.3.8 inside a centos 6.3 virtualbox 4.2.4 virtual machine. The system is running the latest software available via yum update. The host OS is windows 7. The site files nginx is serving are on mounted samba partition, which is a folder on the host Windows system. I.e., inside linux, nginx paths are referring to /home/vhosts and this is mounted from D:\vhosts\ on windows. The samba partition is mounted as root with 777 privileges. /etc/fstab looks like this, but with real ip, username, password: //hostip/vhosts /home/vhosts cifs username=username,password=SECRETPASSWORD,uid=root,gid=root,file_mode=0777,dir_mode=0777,rw,_netdev 0 0 I.e. linux/nginx reads from the windows share, and not the opposite. in /etc/samba/smb.conf, I have tried to disable all samba locking features, but it seems to have no effect even after rebooting the virtual machine. locking=no share modes=no oplocks = no level2 oplocks = no kernel oplocks =no I'm receiving "Access is denied" errors in Windows or linux when attempting to overwrite the javascript file in windows that has been accessed at least once with nginx. If I run "service nginx reload", the lock is removed and I'm able to save the file. That's why I think it is nginx causing the lock. The same problem occurs with directories. However, that may be a different issue not related to the use of samba. I'm using samba so that I can manage the source code outside of the virtual machine. Also note that after I run "service nginx reload", the file I'm editing is actually automatically deleted from the windows host. SOLVED: I just reviewed my nginx.conf file. It appears the "open_file_cache" feature is what is causing the lock and deleted files. When I set this option to open_file_cache off;, My problem is resolved. I will repost as the answer when it allows me to do so.

    Read the article

  • managing a high traffic media sharing website

    - by Jordan Westerman
    i'm in the process of developing a website that i predict will generate a lot of traffic. the site will be similar to many other sites offering free media streaming: mp3's. we are going to start with a pretty minimal amount of media to share, but the basic idea is that artists will set up a profile page with music they have made available for consumers to visit the page and listen to the music. we are starting with just a handful of artists, but i think that this project will generate more and more artist pages. eventually i'd like to set it up so consumers can create personalized playlists. how can i best prepare server space and bandwidth capabilities? i have a small team of web designers and programmers working on the site, as i am pretty illiterate when it comes to site management. as the ring leader of this organization, i am more or less looking for financial requirements and monthly burn rate estimates. i don't have a ton of capitol to start with, putting together a business plan, but i am seeking investments. i have a game plan to grow fast enough to be successful, and slow enough to manage the financial growth requirements. any questions i may have failed to ask myself? is it realistic to start this project on a shared server, and upgrade? any financial advice you think i can use? i really appreciate any advice given, as this is my first business venture. thank you all in advance. Jordan Westerman D.B.A. Badfish Productions, LLC

    Read the article

  • btrfs: can i create a btrfs file system with data as jbod and metadata mirrored

    - by Yogi
    I am trying to build a home server that will be my NAS/Media server as well a the XBMC front end. I am planning on using Ubuntu with btrfs for the NAS part of it. The current setup consists of 1TB hdd for the OS etc and two 2TB hdd's for data. I plan to have the 2TB hdd's used as JBOD btrfs system in which i can add hdd's as needed later, basically growing the filesystem online. They way I had setup the file system for testing was while installing the OS just have one of the HDD's connected and have btrfs on it mounted as /data. Later on add another hdd to this file system. When the second disk was added btrfs made as RAID 0, with metadata being RAID 1. However, this presents a problem: even if one of the disk fails I loose all my data (mostly media). Also most of the time the server will be running without doing any disk access, i.e. the HDD's can be spun down, when a access request comes in this with the current RAID 0 setup both disks will spin up. in case I manage a JBOD only the disk that has the file needs to be spun up. This should hopefully reduce the MTBF for each disk. So, is there a way in which I can have btrfs setup such that metadata is mirrored but data stays in a JBOD formation? Another question I have is this, I understand that a full drive failure in JBOD will lose data on the drive, but having metadeta mirrored across all drives, will this help the filesytem correct errors that migh creep in (ex bit rot?) and is btrfs capable of doing this.

    Read the article

  • How small (spec wise) can a virtual machine be and still boot up and run some sort of OS?

    - by IllvilJa
    One of the advantages with virtual machines is that you can be very flexible with their sizes. If the host system permits it, you can have a very large virtual machine with a lot of virtual RAM and disk. Also, you can decide to go the other way around, to give the virtual machine a very modest amount of RAM and disk and then choose and configure the OS appropriately. The question is, how small virtual machines have people managed to setup (and get to both boot up and to run)? Virtual machines doing something usuful is preferable, even if I know "useful" in this context is awfully subjective, but laboratory-cases with a configuration stripped beyond common sense could be intresting as well, just to see what people manage to boot and run. Quite open ended question and quite academic, but think of it: an extremely small VM (which still does something useful) takes very little memory and disk and can be quite quickly saved to and restored from disk. If it's also gentle on CPU resources, one might consider having a huge number of such VMs up and running on a host. (Imagine a VM running just an old Commodore 64 or Commodore Amiga in it. Ok, way wrong CPU architecture for modern Virtualization software running on a x86-based PC but still an interesting thought. You could have quite a few such small VMs running on a modern PC.)

    Read the article

  • Pentium 4 Willamette vs. Faster Celeron Northwood [closed]

    - by Synetech inc.
    Which is the preferable of the following two processors? Intel® Pentium® 4 Processor 1.70 GHz, 256K Cache, 400 MHz FSB Willamette Intel® Celeron® Processor 2.40 GHz, 128K Cache, 400 MHz FSB Northwood Details: A few months ago my motherboard died, so I bought a used computer that had a 2.4GHz Celeron. My old system had a 1.7GHz Pentium 4, so now I’m trying to decide which CPU to use. Obviously a P4 is preferable over a Celeron, but the Celeron is (significantly?) faster than the P4. I’m wondering if the faster Celeron might be better for certain tasks (ie, stronger but dumber is better at some things than smarter but weaker). I tried Googling for some reviews and comparisons for graphs to get a clear depiction of which is better overall, but found nothing that helped. (I did manage to find one page that indicates (apparently by poll, not benchmark) that the Celeron is better.) So which CPU should I use? Does anyone know of some graphs that I can use to compare the two? The system is a general-purpose machine for word-processing, Internet, and casual games (not Crysis, but not Solitaire either). It will be running Windows XP. The board is a 478 with 400MHz FSB.

    Read the article

  • Purge print driver cache on windows 7 with powershell script

    - by Doltknuckle
    [Background] We have been having trouble with our network clients suddenly being unable to print. They get an odd error with a hex code. We determined that something in the driver was messed up and we could resolve the issue by clearing the driver cache and reinstalling the driver. This happens to random computers every so often. We're assuming this is a bug with the latest Dell 2330dn driver since that is the only model that has this problem. [Problem] What we are looking to do is write a Powershell script that would clear the driver cache and redownload the driver. I see a ton of scripts out there to manage queues, servers, and ports, but nothing for local driver cache management. [Current Workaround] Since we have to do this manually, I'll write out the steps so you know what we want this script to replicate. Disable print spooler Restart machine Delete contents of: C:\windows\system32\spool\drivers\w32x86 Enable print spooler and start service. Delete the network printer object and re-add network printer off of server. [Request] I'm good enough with powershell to translate the above workaround into a pair of scripts. I'd like to find a more elegant solution then my current workaround. Any suggestions?

    Read the article

  • Configuring port forwarding for SSH - no response outside LAN [migrated]

    - by WinnieNicklaus
    I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

    Read the article

  • Configuring port forwarding for SSH - no response outside LAN

    - by WinnieNicklaus
    I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

    Read the article

< Previous Page | 366 367 368 369 370 371 372 373 374 375 376 377  | Next Page >