Search Results

Search found 10844 results on 434 pages for 'device mapper'.

Page 371/434 | < Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >

• Windows Remote Desktop: "configuring remote session" closes without error

  - by icelava

  I have a desktop/laptop pair at home operating x64 Windows 7 (the desktop was upgraded from Windows Vista, works just fine). I remote desktop to them on a daily basis when outside. In recent weeks, I would occasionally fail to connect to my desktop. It can connect and authenticate fine, but the "configuring remote session" dialog would simply close and not show me the desktop window or any error message. There is no error event log relating to this on the desktop computer. Some suggestions call for disabling remote audio, which mine already is, but trying different audio modes did not yield any different result. I am not too sure if this is related to video card drivers (they do get auto-updated), since remote desktop video is supposed to steer via a virtual device driver? Nonetheless the desktop operates three monitors via an ATI Radeon HD5770 (1 Displayport, 2 DVI). I do not see a real problem with that since I can mostly connect and operate it remotely. I try to "remote tunnel" via my home laptop but obviously won't work either as the problem lies in the desktop. What other conditions can cause remote desktop to break without error? UPDATE I came home and still couldn't connect to the desktop until I restarted the entire system.

  Read the article

• No audio in my ubuntu system

  - by hap497

  Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

  Read the article

• Single computer on network cannot connect to internet.

  - by user34630

  Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

  Read the article

• USB 3.0 hard disk not detected on a particular host controller?

  - by Alvin Wong

  I have a USB 3.0 hard disk which has always been working on my desktop with an XHCI. Now I just bought a notebook with an XHCI (something with Intel's Ivy Bridge setup). The first time I plug the hard disk in its 3.0 port it is detected and working. A few hours later I try to connect it again, but seems that the notebook just ignored it! The light on the hard disk didn't blink as usual (instead it is hold at on). I then tested it with my desktop again and it is working perfectly. It gets trickier when I plug it in the USB 2.0 port of that notebook it is detected and working perfectly (despite the slower speed). Then I try to plug in an USB 2.0 USB flash drive to that USB 3.0 port, and it is detected (of course as USB 2.0). So, there are two USB 3.0 ports on my notebook's XHCI. Both of them are not working with my hard disk but working perfectly fine with my USB 2.0 UFD. What's wrong with it? When I plug in the hard disk, device manager doesn't change. I've tried re-installing the driver for the XHCI, but it changes nothing. Had I broke the USB 3.0-specific pins of both USB 3.0 ports?

  Read the article

• Why does my DSDT table is different from what I found online?

  - by Hao Shen

  I have found a field in DSDT table where I want to modify from here http://www.ztex.de/misc/c2ctl.e.html Generally, I want to modify the _PSS field about the processor so that I can have more frequency levels available in the CPUfreq driver interface. I try to use this command to dissemble the DSDT table from my Desktop(Linux2.6.29,Intel CORE 2): cat /proc/acpi/dsdt > dsdt.aml iasl -d dsdt.aml Then I have a file dsdt.dsl as following(very long, so I just show the beginning of the file): /* * Intel ACPI Component Architecture * AML Disassembler version 20090123 * * Disassembly of dsdt.aml, Mon May 6 20:41:40 2013 * * * Original Table Header: * Signature "DSDT" * Length 0x00003794 (14228) * Revision 0x01 **** ACPI 1.0, no 64-bit math support * Checksum 0x46 * OEM ID "DELL" * OEM Table ID "dt_ex" * OEM Revision 0x00001000 (4096) * Compiler ID "INTL" * Compiler Version 0x20050624 (537200164) */ DefinitionBlock ("dsdt.aml", "DSDT", 1, "DELL", "dt_ex", 0x00001000) { Method (DBIN, 0, NotSerialized) { Noop } Scope (\) { Device (_SB.VBTN) ................... But I can not find the _PSS field as shown in the website I have given above. I do not know why? I am sure the current cpufreq driver shows 4 frequency levels available. So at least there should be something in the table showing this..right? Has anybody here played with the DSDT table before? Thanks,

  Read the article

• Load balanced IIS. Should I use NLB, or linux-based reverse proxy, or something else?

  - by growse

  What would be the best approach for load-balancing at least 2-3 Windows 2008 R2 IIS webservers running a multitude of .NET applications? My choices appear to be: 1) Hardware-based network device load balancer, like a Cisco CSS 2) Windows NLB 3) Some sort of linux based proxy, either haproxy or other The three servers sit as VMs on a vSphere farm, so I have the ability to clone to up the instance count in times of high load. I control the switch that the vSphere hosts are plugged into (Cisco 3750), but don't control the switching/routing infrastructure beyond that to the clients. (1) Is too expensive, and probably overkill for my needs. I've included this in case someone figures out a cunning way to do it on my existing network kit, which I doubt. (2) would seem to be the obvious "built-in" option, but seems to be quite fiddly messing around with network interfaces, multicast, and generally other things that seem to be needlessly complex. It's also fairly stupid, in that it can't remove hosts from the pool if they start throwing 500 errors or otherwise go wrong (3) is the most interesting option, as it would appear to offer the most flexibility and customizability, but without having to mess around with the network. However, while I'm familiar with the reverse-proxy capabilities of lighttpd etc, I'm not that well read on other options like HAProxy, which might be able to offer a lot more. Which would you go for, and is there anything I've not thought of?

  Read the article

• MAMP Pro .xip.io, fixing urls with htaccess

  - by user3540018

  I've got all my websites set up with MAMP Pro. For instance, I got it set up, so when I go to example.com, the browser displays the website that's set up on my iMac. Now, I wanna get MAMP Pro to work so I can view my website on my other computers/devices (which are all hooked up on the same network.) So far all I had to do is check the checkbox "via Xip.io (LAN only)", and now I can view my website on my other computers/devices within my LAN by simply going to example.com.10.0.1.13.xip.io. Problem is, whenever I'm on this other computer/device, when I click on the links, I get 404 error. ie. whenever I go to example.com/news, I get the 404. But when I go to example.com.10.0.1.13.xip.io/news, THEN I get the right page. So in order to solve my problem I need to rewrite the urls. So whenever someone clicks on a link ie. goes straight to example.com/news, he'll go to example.com.10.0.1.13.xip.io/news. I don't want to change all the links in my MySQL file, but I believe I can do it simply with the htaccess file. I've opened the htaccess file and added the last two lines, but it just doesn't work. <IfModule mod_rewrite.c> RewriteEngine On # Send would-be 404 requests to Craft RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/(favicon\.ico|apple-touch-icon.*\.png)$ [NC] RewriteRule (.+) index.php?p=$1 [QSA,L] RewriteCond %{HTTP_HOST} ^example\.com RewriteRule ^(.*)$ http://www.example.com.10.0.1.13.xip.io/$1 [R=permanent,L] </IfModule> Or perhaps I don't need to change the htaccess file, is there something that I could be missing in the MAMP Pro settings, or perhaps a MAMP extension that I need?

  Read the article

• AMD switchable graphics are not working OR I don't know how to make them work

  - by Deus Deceit

  I don't know if this is the right place for this question, but I'll give it a shot. I have a Dell Inspiron 17R 5721. It's supposed to be using switchable graphics. It has an Intel HD 4000 and a Radeon HD 8730M and I'm using windows 8. My problem is this, I Installed the drivers that dell gives me but I don't see the AMD graphics card ANYWHERE ( I do see it in device manager but not anywhere else to select and play a game using AMD). I installed the latest drivers from AMD and same thing, I can't run a game with AMD graphics card. I change the applications preferences in the Catalyst control center but even after that, games don't give me the option to select the AMD card, they list only the Intel HD 4000. Can someone tell me what I have to do to make this work? ------------------- After looking around and messing with stuff. I think.... I THINK that you don't really get the option to select a graphics card. Switchable graphics is all about switching automatically depending on application's needs. Cause when I uninstalled AMD's drivers or actually (screwed up lol) games were playing much worse. When I re-installed them, games went back to being good looking. So even if a game sees only the Intel HD 4000 graphics card windows or AMD's drivers will switch to the AMD Readeon graphics card automatically. I hope someone can verify this. Cause seriously I don't think you get to play scyrim with High graphics settings or even ultra with the Intel HD Graphics card. -------------------

  Read the article

• Reliable applicance for routing IT emergency calls (SIP and ISDN)

  - by chiborg

  We have a fairly big IT installation and our IT staff needs to be reachable 24/7. At the moment we have the following setup for "emergency" calls to our IT staff on our main Asterisk box: An incoming emergency number (connected via SIP trunk and a BRI card in case the SIP trunk goes down). When the number is called during the office hours, all the SIP phones of the IT staff are called simultaneously. When the number is called out of office hours interface, a list of mobile phone numbers is called, one after another until someone picks up. The list can be changed by the IT staff via command line script. The setup works well, but the Asterisk is heavily used in a call center, has experienced some outages and misconfigurations, each of them bringing down the IT emergency number. So we'd like to put the IT emergency call functionality on a separate device. This does not need to be a big server, it even does not need to be Asterisk, it only has one purpose and should do it reliably. It should be very low-maintenance. Any suggestions for hard- and software?

  Read the article

• Split MPEG video from command line?

  - by Tim

  I have a homemade DVD that I'm effectively trying to insert chapters into and rearrange - the original author burned it as one long chapter, and I'd like to rip it into smaller pieces and re-encode it into a new DVD. I ripped the DVD with the following command: mplayer dvd:// -dvd-device /dev/sr2 -dumpstream -dumpfile raw.vob I'm running Gentoo Linux with mplayer version 1.0-rc2_p20090731 (the latest available in Portage). I have a list of times that the chapters are supposed to span (for example 30:11-33:25), so my first thought was to rip the entire DVD and use mpgtx to cut out certain pieces of the file. My issue is that running mpgtx -i on the file reports quite a few timestamp jumps: Time stamps jumped from 59.753789 to 0.001622 at position 1d29800 Time stamps jumped from 204963823030450.343750 to 31.165900 at position 2d4f800 Time stamps jumped from 60.077878 to 0.001622 at position 43cc000 Time stamps jumped from 60.024233 to 0.001622 at position 65c5000 Time stamps jumped from 204963823068631.718750 to 52.549244 at position 7fd1000 I've tried to fix the indexes using: mencoder raw.vob -oac copy -ovc copy -forceidx -o fixed.vob -of mpeg But mpgtx will still report timestamp issues. My immediate question: is there a way to take the ripped movie I have and correct its timestamps so I can cut it with mpgtx? If I can get that one issue out of the way, building the rest of the DVD will be smooth sailing. If it's not possible to fix the timestamps on this file: is there a better way to rip small chunks of the DVD into separate files for recompilation later? I'd very much like this to be done on Linux, and it'd be even better if I could script it somehow (feed in a list of start and end positions, or start times and durations, and get out a series of ripped files). If need be, I also have a Mac OS X machine available, but no Windows. Edit: I wound up finding another solution involving HandBrake and ffmpeg (with help from this question), but the question stands. Edit again: Turns out my other solution didn't quite work - the audio desynchronized by about five seconds, in about half of my cut mpgs - so I'm back to square one. Anyone?

  Read the article

• Eee PC Seashell series netbook screen is cut off at bottom no matter the resolution

  - by Yzmir Ramirez

  I have an Eee PC 1015PE Seashell netbook running Windows 7 Home Premium with an Intel Graphics Media Accelerator 3150 (8.14.10.2230) with a "Generic Non-PnP Monitor" detected. I tried: Changing the resolution (Control Panel = Appearance and Personalization = Display = Screen Resolution) to 1024x768 Updating the video driver (to 8.14.10.2230) Uninstalling the driver and rebooting Pressing the Windows Key + "-" (magnifier) Pressing Ctrl + Mouse Scroll only resizes the desktop items Pressing Fn + F4 shows 1024x600 (which I think is what I should be using, but nothing happens) EDIT: Changed from Landscape to Portrait and it works Attached an External Monitor and when I extend or set as desktop it works only on the External Monitor (shows up as "Generic PnP Monitor in Device Manager) Basically the bottom inch of my desktop is off-screen hiding my start bar, but my wigets are in their proper position (the start bar is not hidden). Pressing Ctrl + Esc shows the start menu but its cut-off. I'm pretty sure I should be using 1024x600 resolution, any advice? What's odd is that this only started happening recently. EDIT2: Here are some screenshots showing the problem: Resized Window to fit: Opened Start Menu - notice it cut off: Maximized window and then scrolled down - notice no Start Menu: I downgraded my graphic driver I downloaded from the Intel Download Center for the Graphic Media Accelerator 3150 (now: 8.14.10.1972) and now my "Generic non-PnP Montior" detects as "Digital Flat Panel (1024x768 60Hz)".

  Read the article

• How do I setup routing for 2 companies with different Internet connections on the same LAN?

  - by Clint Miller

  Here's the setup: 2 companies (A & B) share office space and a LAN. A 2nd ISP is brought in and company A wants it's own Internet connection (ISP A) and company B wants it's own Internet connection (ISP B). VLANs are deployed internally to separate the 2 company's networks (company A: VLAN 1, company B: VLAN 2, shared VOIP: VLAN 3). With separate VLANs it's simple enough to use separate DHCP servers (or separate scopes on the same server) to assign the default gateway to each company's gateway for their Internet connection. Static routes can be created on each gateway to point traffic destined for the other company's VLAN or the voice VLAN so that all nodes are reachable as expected. However, I think this is a form of asymmetrical routing, right? (The path from node A1 to node B1 is not the same as the path back from node B1 to node A1). Can I setup policy-based routing to correct this? In that case, can I assign the same default gateway to every device on all VLANs and create a routing policy on a L3 switch to look at the source address and forward traffic to the appropriate next hop? In that case, I want the routing logic to go like this: If the destination address is known, forward the traffic (traffic destined for a different VLAN). If the destination address is unknown, forward the traffic to ISP A's gateway if the source address is on VLAN A; or forward the traffic to ISP B's gateway if the source address is VLAN B. Am I thinking about this problem in the correct way? Is there another way to solve this problem that I am overlooking?

  Read the article

• Tcpreplaying using VMware

  - by Methos

  This is more like a testbed setup question. I want to use VMware to debug some networking code in the linux kernel in the VM. My VM has two network interfaces. What I want to do is replay the capture file in the host and receive the packets in the VM. My problem is I do not see replayed packets in the VM. I am running VMware and tcpreplay on the host as sudo. Hence I think there should not be any problem access devices files. I am running VMware workstation 7.0 a. I first began with Custom networking as that provides option of creating your own virtual network name. I wrote /dev/vmnet3 and /dev/vmnet4 for the two interfaces respectively. However, after booting the guest, I did not see any of these interfaces or devices files (in /dev) created on the host. b. Then I tried 'Host Only', but that does not show what bridge/device file is associated with the interface. c. Finally I tried bridged networking mode. I see vmnet1, vmnet8 and vboxnet0 on the host. I have tcpreplayed the capture file on each of these interfaces, for all the above three cases. I tried to capture packets in the VM using "tcpdump -i any". However, I do not see any packets. Any ideas/pointers?

  Read the article

• When I restart my LXC environment, the container does not re-bind to the IP address

  - by RoboTamer

  The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

  Read the article

• No headphone or speakers plugged in - Windows 7 issue

  - by Amit Ranjan

  I am facing a wierd issue between my sound card driver and Windows7(any edition). I have a sony vaio notebook (VPCEB24EN). Two days ago, on start I got diabled wifi, charging and speakers. Then I restart the PC and everthing worked fine. Later on I again restarted my machine, and then I found the my speakers were not working. I thought, restart will work. I restarted many more times but it did'nt work. I searched google and found that , it might be due to : 1. Hardware is not switched on from bios. 2. No hardware. 3. overriding 64-bit drivers with 32-bit drivers. To make it working, I restored my laptop from scratched, but while restoring pc, the realtek HD drivers, it gave me an error 505. I then formatted the drive and installed Win7 Ultimate 32bit (With PC was, Win7 64-bit Home Basic). I got lots of yellow exclamation in device manager, thinking now this will resolve my issue. But Even after the installing all drivers on a fresh installation, I was still with the same position. A red cross on speaker- No Speakers or Headphone plugged in. Please Note: My Laptop is Vaio , E Series, VPCEB24EN. Audio : Intel® High Definition Audio compatible but accepts Realted Audio. While using BIOS Agent, I got Intel Chipset 5 Series Audio Adapter and ATI RV370 Audio adapter found on my board. Installed is Win7 32bit Ultimate. factory default was Win7 64-bit Home Basic Memory: RAM 3GB/ 320GB HDD Display : ATI Mobility Radeon™ HD 5145 Graphics

  Read the article

• What does a connection timeout indicate when performing an NFS mount?

  - by DeeDee

  We have a shiny new QNAP NAS (TS-879U-RP), and I'm trying to mount it to our big ol' RHEL server in the same manner as our other two QNAP NAS devices. The IT department won't give me the root privileges to the NAS, so I can't SSH in (I know, I know). The first thing I did was to, via the QNAP web admin interface, create a network share named "Runs." I then added the IP of the RHEL server to the permissions list: On the RHEL server, I then added the following line to /etc/fstab: [IP of NAS]:/Runs /mnt/gsrnas3 nfs defaults 0 0 Aside from the IP and the specific mount directory name, this is how I mounted the other two NAS devices. I then created the gsrnas3 directory under /mnt/, and then ran `mount /mnt/gsrnas3' I got the following error: mount.nfs: Connection timed out My first thought is that it's a ports issue, but I don't have enough specific experience with this issue to know for sure. I have two other NAS devices by the same manufacturer already mounted to this RHEL server, so that leads me to believe the configuration issue is on the NAS side of things. I can ping the NAS device successfully from the RHEL server. Not being able to SSH into said NAS is a huge hassle, though. Any ideas?

  Read the article

• How can I uninstall Broadcom Bluetooth software that won't disappear in Windows XP?

  - by T. Webster

  My situation is similar to this question for Windows 7, except my OS is Windows XP SP3. I have recently realized I made the mistake of buying a Bluetooth adapter and installing the Broadcom/Widcomm Bluetooth stack driver software. Now that I know that the software is no good, I want to uninstall it. Then I'll install the Toshiba stack for the Cirago adapter. Right now, when I double-click on the setup.exe file that came with the Cirago driver, nothing happens (it doesn't start setup). I've attempted to uninstall all Bluetooth driver software in Device Manager, and I don't see any remnants of any Bluetooth drivers there. But I do see that the little Bluetooth icon still persists: I don't see anything about Bluetooth, Broadcom, or Widcomm in Add/Remove Programs. I don't see any folder names Broadcom or Widcomm in Program Files folder, either. But I do see that Broadcom does show up in the registry with respect to Bluetooth, as shown here. I also renamed every file in C:\Windows\inf that starts with "bth" so that it ends with ".old". What should I do now to completely wipe this persistent Broadcom Bluetooth software off my computer?

  Read the article

• CHKDSK is unable to fix NTFS errors

  - by HackToHell

  After my PC shutdown due to power failure, I noticed several errors in EventViewer. The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume2. and The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume C:. So I forced a chkdsk check at startup, and it finds a stream of error, here is the output, it is smaller than the actual log, because, Event Viewer only seems to have this much, the same line was repeated thousands of times.Here is that line. Some clusters occupied by attribute of type 0x80 and instance tag 0x4 in file 0x198f2 is already in use. Deleting corrupt attribute record (128, "") from file record segment 104690. Attribute record of type 0x80 and instance tag 0x0 is cross linked Also, even after running CHKDSK, the same errors were being reported again so I ran CHKDSK another time and it still loops the same line above, without fixing the error. Can anyone tell me how to fix it?

  Read the article

• how would it be possible to discover a cable modem's MAC remotely?

  - by amateurenthusiast

  i was reading the back archives of a canadian privacy law blog, and he linked to a judicial decision. apparently as part of an investigation in which were used yahoo chat and google's old 'hello' image trading program the officer was able to determine a suspect's modem's MAC address: In order to determine who STEPHTOSH was, the officer did a trace on a programme called WHO IS in an effort to learn from where STEPHTOSH was coming. WHO IS is a command program available to the public. The officer was able to ascertain that the person using the name STEPHTOSH was a Rogers Internet customer. The officer was able to obtain the Internet Protocol address, also known as the I.P. There is only one location for an I.P., which is unique to that subscriber. By use of the website known as DNS STUFF.com, one is able to find with which company this I.P. is registered. It was ascertained that the I.P. address used by STEPHTOSH was registered to Rogers Cable, from the Toronto area. The officer also learned the Cable Modem MAC address used by STEPHTOSH. This was all the information the officer was able to amass. now it was my understanding that the MAC address of any given device can only be accessed if you're only one 'hop' away on the Internet. the suspect in question was in Markham and the officer part of the Toronto Police, so it's conceivable that they both might have used Rogers internet. but would that still put them only one 'hop' away from each other? i thought the first hop after the modem was usually the ISP? and if he'd used a netBIOS query against this guy's machine it would return the ethernet card's MAC, not the modem's. so is this guy on the same rogers subnet as the suspect's cable modem, is that functionality part of google's Hello (i could only think that it would be possible if Hello operated as a virtual LAN or something), does the officer have remote access to the arp caches of the routers at Rogers or is he just full of crap and lying to make his case stronger?

  Read the article

• How to reinstall Windows Boot Manager on EFI partition

  - by joaocandre

  So I've been trying to install Ubuntu on a second HDD on my desktop, which has W8 installed on a SSD (UEFI-only boot). Thing is, during Ubuntu installation I made the mistake of choosing to install the bootloader (GRUB) to the first disk (the SSD), and after install I could not boot into W8 (the entries in GRUB didn't work). Following these instructions, I managed to be able to get "Windows Boot Manager" back, however I lost GRUB in the process, and got a duplicate "Windows Boot Manager" entry in BIOS, along with the "Ubuntu" entry, which then I used to boot into Ubuntu. Later, I decided to reinstall Ubuntu, and formatted the HDD from within windows, however, the entries in BIOS stayed the same, and, while I had the HDD connected to the motherboard, I could not boot into an Ubuntu Live USB (in order to reinstall Ubuntu). I made another mistake by updating the BIOS, which cleared all of the EFI boot entries in BIOS, and, right now, I get an error when boot from the SSD: grub: device not found (...) So it seems that grub is still installed in the EFI partition of the SSD, and since I don't have the WBM entry in BIOS anymore, I cannot even boot into Windows, and the previous instructions don't work anymore. Is there another way to reset W8 EFI partition to the default?

  Read the article

• Debian: What are these files in /sys/devices/pci0000:00/ for?

  - by muhuk

  I am running Debian Squeeze on an MSI M670 laptop. I have these following files on my root drive, each 256MB: file:///sys/devices/pci0000:00/0000:00:05.0/resource1 file:///sys/devices/pci0000:00/0000:00:05.0/resource1_wc Here is my lspci output: muhuk@debian:~$ lspci 00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2) 00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: nVidia Corporation C51 [GeForce Go 6100] (rev a2) 00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3) 00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) 00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 04:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 04:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 04:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 04:09.0 Network controller: RaLink RT2561/RT61 rev B 802.11g I am speculating these have something to do with the shared RAM my GPU is using. But why a file on disk? And why two of them?

  Read the article

• Microsoft SQL Server Management Studio causing system freeze

  - by CRoshanLG

  I'm experiencing very slow response from MSSMS and it causes other applications to slow down. Specially Skype crashes after few seconds from opening MSSMS, showing an error called "Disk I/O Error". I'm regularly using few applications (Sublime text, MS Word, Firefox, Outlook, Skype and one or two other apps) simultaneously. The system works fine when MSSMS is not in use! But as soon as MSSMS is opened, all the apps start to freeze (MSSMS also responds very slow). This problem has been there for about a week now (I haven't installed any apps or haven't made any changes to the system during that time). -- System Specifications -- Processor: Core i3 (3.1 GHz) RAM: 4 GB OS: Windows 7 Professional (64 bit) Free space in C drive: ~ 100 GB MS SQL Server 2008 R2 Microsoft SQL Server Management Studio version - 10.50.1600.1 I've tried to find a reason for this but there are no helpful information in the web! There are some solutions suggested (in forums and in Skype Support pages) for the Skypes' "Disk I/O Error", all of which I tried but does not solve the problem. Has anyone faced the same senario? (and hopefully) knows a solution? Systems Log I don't have much knowledge in interpreting the System Log, but I think the Critical and Warnings are not helpful. But there are lots of Error logs which might be useful. In source Kernal-General there are few similar errors saying "An I/O operation initiated by the Registry failed unrecoverably.The Registry could not flush hive (file): <some file>" In source atapi also there are few similar errors -- "The driver detected a controller error on \Device\Ide\IdePort0." (all errors has occurred in 'IdePort0') In Application Error, there are several errors logged, and following is the latest one. Both the Errors which has occurred today is similar (to this one). As it is from Ssms.exe, I guess this is relevant to the cause of problem. But as I said above I can't understand what it means!

  Read the article

• Loss of network connectivity when playing video on Optoma HD180 projector

  - by Jeff Fohl

  Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas?

  Read the article

• Cannot install CentOS 6.5 using UEFI usb boot

  - by Vaindil

  I am trying to dual-boot CentOS 6.5 on my desktop that is currently running Windows 8.1. I have two storage devices: an SSD that has my Windows installation, and an HDD that has all of my data. Both are formatted using GPT, and Windows boots using UEFI. I used the CentOS 6.5 live DVD (CentOS-6.5-x86_64-LiveDVD.iso) to create an EFI-bootable flash drive (it does boot properly in EFI mode). I receive an error, however, when CentOS is booting (error is below). I have a 6.4 boot DVD which boots as expected, but it does not boot in UEFI mode and therefore doesn't play nicely with my Windows installation (I have no way to access it, even using rEFInd or any other similar tools). What do I need to do to get the device to boot properly in UEFI mode? Kernel panic - not syncing: Attempted to kill init! Pid: 1, comm: init Not tainted 2.6.32-431.el6.x86_64 #1 Call Trace: [<ffffffff815271fa>] ? panic+0xa7/0x16f [<ffffffff81077622>] ? do_exit+0x862/0x870 [<ffffffff8118a865>] ? fput+0x25/0x30 [<ffffffff81077688>] ? do_group_exit+0x58/0xd0 [<ffffffff81077717>] ? sys_exit_group+0x17/0x20 [<ffffffff8100b072>] ? system_call_fastpath+0x16/0x1b drm_kms_helper: panic occurred, switching back to text console

  Read the article

• need advice on data center move, communication with both facilities during transition

  - by Brian Roden

  We are beginning the process of moving to a new facility. Office and warehouse operations will both be moving, and we must get shipping operations up and running at the new location while continuing to ship from the old location. Our contract with some third-party warehouse tenants requires two business day turnaround (only weekends and holidays excluded), so we can't have major downtime during the move. We would like to keep our 172.16.60/61.xxx internal address space in use throughout the move. Is it possible to keep using this same internal range, and have our existing WatchGuard Firebox 520 and whatever router we get for the other location (preferably the same model) just treat both locations as one network, leaving our host IPs the same throughout the move? Renumbering the servers when they move isn't a big deal, but our wireless terminals for order picking in the warehouse have fixed IPs (and a fixed IP, non-DNS reference to the host they speak with) and would be a massive undertaking to reconfigure when the servers move (each device would have to be reconfigured at least 2 times -- some when we start using them in the new building and the host is still here, all of them in both locations when the host moves to the new building, and the rest when they finally make the move to the new building). We're trying to avoid that if possible.

  Read the article

< Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >