Search Results

Search found 13004 results on 521 pages for 'pretty printing'.

Page 371/521 | < Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >

• Can I recover a zpool after it's been exported, given that devices have not been reallocated?

  - by cali-spc

  I had a zpool we'll call 'testpool'. testpool had 3 devices included in it, and a single zfs called 'test'. I needed to move 'test' to a new, smaller pool. I wanted to name the new pool the same name 'testpool'. Basically did the following. zfs send testpool@backup > /tmp/test-dump zpool export -f testpool zpool create -f testpool newdevice zfs receive -F testpool < /tmp/test-dump Unfortunately I found out that the testpool@backup snapshot was the wrong snapshot. Too old. I have yet to reallocate the three devices that were in the OLD testpool. (None of these 3 devices are 'newdevice', they are a separate 3.) Is there any way I can recover data in those devices? I'm thinking since I named the new, smaller pool the same as the old zpool, I'm pretty much SOL. But if not, that would be nice to know. Edit: More info I did a 'zpool import' and got this. bash-3.00# zpool import pool: testpool id: 14781458723915654709 state: ONLINE action: The pool can be imported using its name or numeric identifier. config: testpool ONLINE c5t8d0 ONLINE c5t9d0 ONLINE c5t10d0 ONLINE So I'm guessing I just need the syntax to import this zpool using its numeric identifier, while giving it a new name. S.

  Read the article

• What is the best way/Software to manage multiple short lived instances of virtual machines ?

  - by Newtopian

  Hi, We have a QA department that have to test our software on multiple combination of OS and DMBS. With Windows spewing out many different versions the combinatorial math of all this can be daunting. So we decided on visualizing our setups but so far it only displaces the problem. The cost of hardware is expensive and we need many different combination far exceeding your server capacity to deliver. Also, these instances are throw away, once the test is complete we no longer need it, furthermore to ensure proper test isolation we should start fresh from a new instance. Lastly we only need a small subset of these system online at any given time. What I am looking for is a way to manage inventory so that our QA staff can order instances to be put online as required and discarded once used. Instances are spawned from a pool of freshly installed systems with the appropriate combination ready to accept our software. It also should be possible for two or more people to start the same instance at the same time, though we could manage without this if it proves too complex to put in place. Finally our budget is pretty thin, we can probably make some purchases but ideally expenditures should be kept to a minimum. To summarize we should be able to : Bring instances online on demand. Ideally should offer queue and scheduling management Destroy instances on demand Keep masters in inventory but not online. Manage large inventory of VMs (30-100 maybe more) with small staff of users (5-10). Allow adding, deleting and changing instances from inventory (bring online, make changes and check back in, or create new and check in). Allow few long lived instances for support tools (normal VM server usage) Thanks for your answers

  Read the article

• fedora, dhcpd fails to start

  - by soxs060389

  History: I got a tiny shiny plugserver which I want to plug to my ADSL router (or however you want to call it) on one end (eth0), and the other end (eth1) I want to run a dhcp server for my LAN. ATM I am stuck with getting LAN to work. OS is fedora 12. I configured my /etc/dhcp/dhcpd.conf like this: # # DHCP Server Configuration file. # see /usr/share/doc/dhcp*/dhcpd.conf.sample # see 'man 5 dhcpd.conf' # option domain-name "unknown.org"; option domain-name-servers 192.168.44.1; option subnet-mask 255.255.255.0; option broadcast-address 192.168.44.255; default-lease-time 86400; max-lease-time 172800; subnet 192.168.44.0 netmask 255.255.255.0 { host fedorabigbox { hardware ethernet 00:19:66:8E:61:74; fixed-address 192.168.44.21; } #host mobile #{ # hardware ethernet ***; # fixed-address 192.168.44.22; #} range 192.168.44.100 192.168.44.110; option routers 192.168.44.1; } # this is just dummy, as read many howtos, some suggesting to add a subnet blah netmask blah for each interface subnet 192.168.33.0 netmask 255.255.255.0 { range 192.168.33.100 192.168.33.110; option routers 192.168.33.1; } But the server fails to start when trying to start it via /etc/init.d/dhcpd start In general it would be nice if someone can point me to a in detail explanation of how network works, I am pretty new to this stuff. More concrete question: How to point the subnets to eth1 and the other to eth0, how can this be achieved? Does someone see any errors or flaws? Syntax should be correct, allready checked that with the dhcpd syntax check. Thanks for any help

  Read the article

• How to work around blocked outbound hkp port for apt keys

  - by kief_morris

  I'm using Ubuntu 9.10, and need to add some apt repositories. Unfortunately, I get messages like this when running sudo apt-get update: W: GPG error: http://ppa.launchpad.net karmic Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 5A9BF3BB4E5E17B5 W: GPG error: http://ppa.launchpad.net karmic Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 1DABDBB4CEC06767 So, I need to install the keys for these repositories. Under 9.10 we now have the option to do this: sudo add-apt-repository ppa:nvidia-vdpau/ppa See this Ubuntu help article for details. This is great, except that I'm running this on a workstation behind a firewall which blocks outbound connections to pretty much all ports except those required by secretaries running Windows and IE. The port in question here is the hkp service, port 11371. There appear to be ways to manually download keys and install them on apt's keyring. There may even be a way to use add-apt-repository or wget or something to download a key from an alternative server making it available on port 80. However, I haven't yet found a concise set of steps for doing so. What I'm looking for is: How to find a public key for an apt-package (recommendations for resources which have these, and/or tips for searching. Searching for the key hash doesn't seem all that effective so far.) How to retrieve a key (can it be done automatically using gpg or add-apt-repository?) How to add a key to apt's keyring Thanks in advance.

  Read the article

• All virtualhosts serving Apache default files

  - by tj111

  I'm trying to configure Apache as an in-network webserver, and am using the sites-available/sites-enabled feature as opposed to just static vhost files. I set up a couple VirtualHosts, all with a unique DocumentRoot, however request for all the VirtualHosts just serve up the "It's Working!" default file. I can't for the life of me figure out why it won't serve the content out of the correct directory. Here's the contents of the virtualhost directive files, let me know if I need to post more. default (note that apache renames this to 000-default in sites-enabled, so it's not an ordering issue) NameVirtualHost *:80 ServerName emp <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName emp DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> billmed <VirtualHost *:80> ServerName billmed.emp ServerRoot /home/empression/Projects/billmed/web/httpdocs <Directory "/home/empression/Projects/billmed/web/httpdocs"> Order Allow,Deny Allow from All </Directory> </VirtualHost> Note that I have DNS zones for both emp and billmed.emp, as well as entries in /etc/hosts. My ultimate goal is to set up this machine as an in-house webserver with a custom tld (emp), but progress has been pretty slow.

  Read the article

• DV-AVI in DivX Plus Player and VirtualDub - playback issue

  - by user714965

  I have an AVI-video which I had (digitally) transferred from a DV camera to my PC. The video contains errors at the beginning most likely because the DV tape was pretty old. When playing this video in the DivX Plus Player I get some picture artefacts and some high noise peaks of the sound. These stops after two seconds. When I'm playing this video in VirtualDub (where I want to cut it) I get the same picture artefacts. But the sound errors (those loud high peaks) lasts ten seconds. These sound errors are also contained in the cutted video. Why does the video have more errors when played in VirtualDub? I think because of different codecs which are used for decoding the video? How can I change the codec which VirtualDub uses for decoding? I have installed ffdshow for this but it seems that it is not used because I don't get the ffdshow icon in the taskbar when playing the video in VirtualDub. When playing in DivX Player Plus I get this icon.

  Read the article

• localhost/127.0.0.1 not working, "Unable to connect"

  - by redconservatory

  I am running some pretty basic php sites on Snow Leopard. Usually I just go to my browser and type anything like: localhost http://localhost 127.0.0.1 mycomputername.local But suddenly, after installing a gem file (compass) none of this is working. I tried sudo apachectl restart Thinking that I just needed to restart apache, but no luck. My error log looks like: [Mon Mar 26 09:39:08 2012] [warn] child process 45443 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45223 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45043 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45438 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45049 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45439 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45224 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45440 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45441 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45442 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45443 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:11 2012] [notice] caught SIGTERM, shutting down I also tried sudo apachectl -k start And I got the error: Syntax error on line 182 of /private/etc/apache2/httpd.conf: Illegal option When I look at the code around that line, I see: <Directory /> Options Indexes MultiViews + FollowSymLinks AllowOverride All Order allow, deny Allow from all </Directory>

  Read the article

• ospfd over an OpenVPN link - strange error in logs

  - by Alex

  I am trying to set up Quagga ospfd on two hosts connected by an OpenVPN link. These hosts have VPN IPs 10.31.0.1 and 10.31.0.13. ospfd config is pretty simple: hostname bizon password xxxxxxxxx enable password xxxxxxxxx ! log file /var/log/quagga/ospfd.log ! interface lo ! interface tun0 ip ospf network point-to-point ip ospf mtu-ignore ip ospf cost 10 interface tun1 ip ospf network point-to-point ip ospf mtu-ignore ip ospf cost 10 interface tun2 ip ospf network point-to-point ip ospf mtu-ignore ip ospf cost 10 ! router ospf ospf router-id 10.31.0.1 network 10.31.0.0/16 area 0.0.0.0 network 10.119.2.0/24 area 0.0.0.0 redistribute connected area 0.0.0.0 range 10.0.0.0/8 ! line vty ! debug ospf event debug ospf packet all I am getting the following error in the ospfd.log (the log is from 10.31.0.13): 2012/10/05 01:25:28 OSPF: ip_v 4 2012/10/05 01:25:28 OSPF: ip_hl 5 2012/10/05 01:25:28 OSPF: ip_tos 192 2012/10/05 01:25:28 OSPF: ip_len 64 2012/10/05 01:25:28 OSPF: ip_id 64666 2012/10/05 01:25:28 OSPF: ip_off 0 2012/10/05 01:25:28 OSPF: ip_ttl 1 2012/10/05 01:25:28 OSPF: ip_p 89 2012/10/05 01:25:28 OSPF: ip_sum 0xe5d1 2012/10/05 01:25:28 OSPF: ip_src 10.31.0.1 2012/10/05 01:25:28 OSPF: ip_dst 224.0.0.5 2012/10/05 01:25:28 OSPF: Packet from [10.31.0.1] received on link tun1 but no ospf_interface I'm not sure what to do next. I have set up ospfd over OpenVPN several times but I used Debian and I am on CentOS 6 now. Quagga version is 0.99.15. Should I try to get more recent version?

  Read the article

• Is my laptop battery dead?

  - by Josh

  Recently my laptop battery will get extremely hot (definitely hotter than it should get) when I charge it. After that I usually end up removing it once it's fully charged to let it cool down, which takes a couple hours... Question is, is my battery dead? My last battery I had that died just ended up lasting 2 - 3 minutes on battery, no weird heat issues. And is there any way to possibly fix this? Probably not but I won't be able to get a replacement anytime soon. UPDATE: A few days ago when this happened and it cooled down, assuming it was fully charged, I ran my laptop on battery, and the battery life lasted about 10 minutes and then the laptop shutdown. I then plugged it in later and charged it back up, and for a while I had a orange light blinking on my laptop - which I assumed meant the battery was dead, especially since I got 10 minutes battery life. Then today, I turned my laptop on and was surprised to see that the battery was at 20% and charging (it's been plugged in since the incident above, so it should have been fully charged when I shut it off) I let it charge up, and as usual it got pretty hot around the time it was fully charged. So I turned my laptop off and pulled the battery out to let it cool down Now the thing is, just now I tried running it on battery, and it's been going for an hour now... so maybe its not dead? (also the orange light is no longer blinking...) Thanks in advance if anyone knows whats going on, and how to fix it, if its fixable =] EDIT: Some info if it helps... my laptop is about 2 years ago, and it's an Asus K50ID. I know laptop batteries usually don't last more than a year but I'm trying to keep this one going for as long as I can.

  Read the article

• HP Proliant DL380 G4 - Can this server still perform in 2011?

  - by BSchriver

  Can the HP Proliant DL380 G4 series server still perform at high a quality in the 2011 IT world? This may sound like a weird question but we are a very small company whose primary business is NOT IT related. So my IT dollars have to stretch a long way. I am in need of a good web and database server. The load and demand for a while will be fairly low so I am not looking nor do I have the money to buy a brand new HP Dl380 G7 series box for $6K. While searching around today I found a company in ATL that buys servers off business leases and then stripes them down to parts. They clean, check and test each part and then custom "rebuild" the server based on whatever specs you request. The interesting thing is they also provide a 3-year warranty on all their servers they sell. I am contemplating buying two of the following: HP Proliant DL380 G4 Dual (2) Intel Xeon 3.6 GHz 800Mhz 1MB Cache processors 8GB PC3200R ECC Memory 6 x 73GB U320 15K rpm SCSI drives Smart Array 6i Card Dual Power Supplies Plus the usual cdrom, dual nic, etc... All this for $750 each or $1500 for two pretty nicely equipped servers. The price then jumps up on the next model up which is the G5 series. It goes from $750 to like $2000 for a comparable server. I just do not have $4000 to buy two servers right now. So back to my original question, if I load Windows 2008 R2 Server and IIS 7 on one of the machines and Windows 2008 R2 server and MS SQL 2008 R2 Server on another machine, what kind of performance might I expect to see from these machines? The facts is this series is now 3 versions behind the G7's and this series of server was built when Windows 200 Server was the dominant OS and Windows 2003 Server was just coming out. If you are running Windows 2008 R2 Server on a G4 with similar or less specs I would love to hear what your performance is like.

  Read the article

• Using my old PC as a web/file server?

  - by Garrett

  I have an old desktop computer that I've been trying to sell for AGES. I guess nobody is looking for computers because it was advertised at a dirt cheap price on craigslist, local papers, etc. Anyways, I was wondering if it would be worth it to set it up as a home file server, a web dev server (I have a web host for actual production use), and maybe host a few server applications (ex: ventrillo). The computer is actually an old Dell that I cannibalized after the motherboard being destroyed by lightning, so it has fairly new parts in it. The specs are: P4 3.4GHz w/ HT and Artic Cooling Freezer 7 3GB DDR2 533 RAM 80GB hdd (will upgrade the hard drive if it's even worth using as a server) basic dvd rom 430 Watt Thermaltake PSU (it might be important to note that it is only 60% efficiency) ATI Radeon x600 256MB Antec 300 case It's not a really beefy machine, I just can't see giving it away or putting it in the corner to just collect dust. I have Windows Server 2008 R2 Standard and I am confident in my skills in operating most Linux operating systems. I'd also be using it to tinker with when I learn new things in my server admin classes (I'm finishing my 2nd year in college at the moment so I'm still learning) Also, my house is quite old and the electrical wiring is pretty poor (it MIGHT be up to code, then again, where I live most people don't even know what regulations are or let alone know how to spell it...) Would it be safe to leave it running all day and is it going to run up my electric bill because of the PSU efficiency? I only have 5mbit cable internet, but I won't be running very bandwidth intense services on it so it should be ok. I should elaborate on why I am concerned about the power. The circuits should be fine, but I'm more concerned about fire hazard. What is the likelihood that the server could cause an electrical fire? Again, thank you all for the feedback!

  Read the article

• Samsung laptop randomly shuts down

  - by Dmatig

  I've rewritten this question because it turned into an indecipherable mess. I have a Samsung R560 laptop that is overheating, and shutting itself down under load consistantly. Thank you quickcel for reccomending me Speedfan to monitor my temps. Here they are (Load / Idle): (Ignore "Temp1 and Temp2", whatever sensors they are they'd always random, pretty sure they're broke). The load temperature is after just 5 minites of playing Fallout 3 - another 5 minutes and it (the GPU - 9600M GS) consistantly breaches the mid 90's then shuts down, so it's hard to get a good picture of it. I'm looking for some solution or way to decrease these temperatures, because they seem far too high even idle. I've tried: Opening up the case and clearing of all dust with compressed air. Updating drivers for my Graphics card Have purchased and am using a notebook cooler I don't want to: Undervolt / underclock (defeats the point of having a more expensive card) Use lower power / performance settings (again, i might as well have bought something cheaper) Is there anything else i can try (software or inexpensive hardware) that can help me fix this? Has anybody had a Samsung laptop and knows if this can be sorted under my warranty, and the turnaround time of sending it off (UK?)(it has always ran hotter than it should, but now at 6 months old is getting hot enough to power off)

  Read the article

• Cisco Configuration backup with Windows Script.

  - by Jeff

  We have a client with a lot of Cisco Devices and we would like to automate the backups of these devices through telnet. We have both 2003 and 2008 servers and ideally use tftp to back it up. I wrote this: Set WshShell = WScript.CreateObject("WScript.Shell") Dim fso Set fso = CreateObject("Scripting.FileSystemObject") Dim ciscoList ciscoList = "D:\Scripts\SwitchList.txt" Set theSwitchList = fso.OpenTextFile(ciscoList, 1) Do While theSwitchList.AtEndOfStream <> True cisco = theSwitchList.ReadLine Run "cmd.exe" SendKeys "telnet " SendKeys cisco SendKeys "{ENTER}" SendKeys "USERNAME" SendKeys "{ENTER}" SendKeys "PASSWORD" SendKeys "{ENTER}" SendKeys "en" SendKeys "{ENTER}" SendKeys "PASSWORD" SendKeys "{ENTER}" SendKeys "copy startup-config tftp{ENTER}" SendKeys "(TFTP IP){ENTER}" SendKeys "FileName.txt{ENTER}" SendKeys "exit{ENTER}" 'close telnet session' SendKeys "{ENTER}" 'get command prompt back SendKeys "{ENTER}" SendKeys "exit{ENTER}" 'close cmd.exe On Error Resume Next WScript.Sleep 3000 Loop Sub SendKeys(s) WshShell.SendKeys s WScript.Sleep 300 End Sub Sub Run(command) WshShell.Run command WScript.Sleep 100 WshShell.AppActivate command WScript.Sleep 300 End Sub But the problem with this is the sendkeys are sent to the console session, I'm trying to find a solution that would not require a user to be logged in. Does anyone have any ideas? I have some knowlage of VBS, PowerShell and a pretty good grasp on batching.

  Read the article

• SQL Server Remote Connections

  - by Barry

  Hi, I am at my wits end with trying to access a remote SQL Server 2008 R2 Express instance. Here are the following that I have tried. 1) I enabled remote connections in the instance properties. 2) I enabled sql server and windows authentication mode and created an account to log in using sql server authentication. 3) I started the SQL Server Browser service 4) I forwarded ports 1433 and 1434 on the router to the IP address of the machine hosting SQL Server. 5) I turned off firewalls on both the Machine running the instance and the router. 6) http://www.yougetsignal.com/tools/open-ports/ I used this to check whether or not both ports were open and it says that they are closed. I have the SQL Server Express instance running and the browser running. I have configured it to allow remote connections yet, it tells me they are both closed. I'm pretty confused at this stage. On the client Machine I am trying to connect using the following format machineip\SQLEXPRESS with SQL Server Management Studio Express. Thanks in advance

  Read the article

• Windows: How to make programs think they're not running in a terminal server session?

  - by sinni800

  I am using the program "SoftXPand 2011 Duo" by Miniframe on my Windows 7 PC. It makes two workstations out of one computer. It uses the terminal services built into Windows to create the additional session. I use two screens, two keyboards and two mice to create this "illusion" of two computers. It works quite well and I can even play two different 3D games on the two screens attached to this single machine (using a Radeon HD5770 and a Core i5 2500k with 8 Gbytes RAM). There are a few downsides to this. I just found about one that is hidden on the first look. The sessions you are in (even on the first workstation) will identify as a terminal server session! Now some programs will run with limited effects (graphical), and some won't run at all. This also resulted in some games not running at all. They just say "Cannot be run in a terminal server session" and exit. I have already proven that top modern games (DirectX 10, 11) run just as good as on the same machine without SoftXPand, so this is a pretty artificial limitation! So, can I somehow hack my current session so it doesn't look like a terminal server session anymore? I. E. #include <windows.h> #pragma comment(lib, "user32.lib") BOOL IsRemoteSession(void) { return GetSystemMetrics( SM_REMOTESESSION ); } Will return FALSE? (Not a programming question! Just an example how programs detect if they're in a terminal server session!)

  Read the article

• How to make Virtualbox, OpenVPN, and Win2008 Web R2 like one another?

  - by Aquitaine

  Back with web developer guy wearing net admin hat. Hopefully this is an easy one. We have two servers on a public network at a hosted facility. Server A is our public-facing web server and server B is our database server. Both are running Windows 2008 Server R2 Web Edition. We want Server B isolated from everything except Server A, such that anyone who has to connect to server B goes through the VPN on Server A. It's not perfect since we have no access to do this on the router side, but it's what we've got. We've set up VirtualBox and OpenVPN Access Server on Server A. It has one network interface set to 'NAT' mode, such that OpenVPN gets its IP at 10.0.2.x, and to connect to the OpenVPN interface, I go to the local IP for the Virtualbox network adapter, 192.168.56.x, which works as I configured the appropriate ports using VBoxManage. My question is, do I need to be using Bridged Networking and give the VPN server its own IP, or is there some way to tell the server (either Windows or the Virtualbox OpenVPN) that 'any public connection on the real external IP on port X should be directed to this internal LAN address of 192.168.1.x on port Y'? OpenVPN itself doesn't seem to be aware of the server's real external IP unless we put it in Bridged networking mode; is that necessary or advisable? We're without RRAS since this is Web edition, but I feel like what we're going for is pretty simple. Thanks! Aq

  Read the article

• Copy one db diagram from one db to another on different servers? (Same db)

  - by sah302

  I used the copy database wizard to copy my database from our test server to our production server, the database copied everything fine except for the diagram. Okay no problem, first I make sure the target database on production has the support objects created to use database diagraming. Then I select to import data from the other database and chose the dbo.sysdiagrams.Go through with the rest of the import data wizard, but then I get the following error: Validating (Error) Messages Error 0xc0202049: Data Flow Task: Failure inserting into the read-only column "diagram_id". (SQL Server Import and Export Wizard) Error 0xc0202045: Data Flow Task: Column metadata validation failed. (SQL Server Import and Export Wizard) Error 0xc004706b: Data Flow Task: "component "Destination - sysdiagrams" (31)" failed validation and returned validation status "VS_ISBROKEN". (SQL Server Import and Export Wizard) Error 0xc004700c: Data Flow Task: One or more component failed validation. (SQL Server Import and Export Wizard) Error 0xc0024107: Data Flow Task: There were errors during task validation. (SQL Server Import and Export Wizard) So apparently it didn't like that. What's the problem? I am pretty beginner in SQL Server and only do stuff via the GUI usually so am not sure what to do at this point. The databases are the same, but on different servers. Thanks!

  Read the article

• Does MySQL have some kind of DoS protection or per-user query limit?

  - by Ghostrider

  I'm a bit at a loss. I'm running a MySQL database that's roughly 1GB data in indices combined on a dedicated Linux server. DB version is '5.0.89-community'. Configuration is controlled via cPanel. PHP actually runs elsewhere on a shared hosting. IP addresses are static and don't change. Access from remote IP address is properly configured. Website gets around 10K hits per day with each hit generating a a database query. Some of these queries are expensive (~1 sec execution time). All is fine and well until at some point DB server starts refusing connections from the client, claiming that specific user can't access the server from that IP. Resetting the server will always fix the problem for a day or two and then the same thing happens. There are some other DBs on that server, some of which are hit pretty hard on occasion but constantnly. One of the apps maintains several persistent connections since it does couple of updates per minute. Though I don't think it's related. What's driving me mad is that I can't figure out why server would start refusing connections. There is nothing in the logs. This server is a hosted dedicated server so hosting company created the OS image and I didn't write or go over every line of configuration. I'd do it but I'm at a loss as to where start looking. Any advice is appreciated.

  Read the article

• Preferred mail system/server for a company?

  - by Trevoke

  Say you are responsible for setting up an email solution at a company. Which would be your choice? I know of the following options, but many of them not well: Gordano Mail System Exchange Exim Postfix Qmail Zimbra For having used it a little over two years, I really, really like Gordano Mail System. They offer a whole bunch of things, like calendaring, anti-spam, anti-virus, extremely complete and filterable logging options, aliases, a customizable webmail interface... And their software can be installed on both a Windows or Linux OS. In addition, their support is top-notch, their knowledgebase comprehensive (and, I will admit with a touch of pride, I have contributed, with my questions, to the addition of a few articles in there). Of course, they're not free, which can be a problem, but they're not Exchange, and they do offer pretty much everything that Exchange offers -- which is great if you want to stay away from that, but need all the features. Although, if you need a Blackberry Exchange Server, or something similar, I'm not sure what you should go for. So.. What would your choice be? Why? I've never played with a more DIY email solution, but I'm sure many people here have and wouldn't trade their setup for the world :)

  Read the article

• Windows 7 mapped drive kicking off OS X users

  - by Collin White

  I've mapped a network drive on my Windows 7 PC at my office. The windows machine has a few TB of storage that is being accessed by my development team (all running mac os 10.7). The share seems to work fine for a little while but will timeout and kick the mac users off and sometimes disallows a connection on the next attempt. Restarting the windows machine fixes the problem. I've tried this tutorial as well as setting the maximum session length in the Local Security Policy section to 99999 (I discovered 0 did not mean unlimited, only a 'reasonable ammount of time') anyway, the setting is now for ~208 days which is sufficient (see attached). I'm having trouble debugging this in general so if anyone has some pointers I'm all ears. This is a intermittent issue which in my opinion are the hardest kinds to debug. If anyone knows of how I might monitor connections from the PC that would also be pretty cool. Previously the files were hosted on a mac mini and everything was working just fine (the mini just didn't have the ability for the storage capacity we needed) so I believe it is some windows setting that is kicking users off. Anyway, thanks for reading.

  Read the article

• SQL Server Remote Connections

  - by Barry

  Hi, I am at my wits end with trying to access a remote SQL Server 2008 R2 Express instance. Here are the following that I have tried. 1) I enabled remote connections in the instance properties. 2) I enabled sql server and windows authentication mode and created an account to log in using sql server authentication. 3) I started the SQL Server Browser service 4) I forwarded ports 1433 and 1434 on the router to the IP address of the machine hosting SQL Server. 5) I turned off firewalls on both the Machine running the instance and the router. 6) http://www.yougetsignal.com/tools/open-ports/ I used this to check whether or not both ports were open and it says that they are closed. I have the SQL Server Express instance running and the browser running. I have configured it to allow remote connections yet, it tells me they are both closed. I'm pretty confused at this stage. On the client Machine I am trying to connect using the following format machineip\SQLEXPRESS with SQL Server Management Studio Express. Thanks in advance

  Read the article

• Can I use a Windows Server 2003 Domain Controller but my home router for DNS?

  - by NetworkingWannabie

  Hi All Probably easiest to start with a description of my current setup, which works (oh, and this is a home setup not an office or anything): I have an ADSL modem with a static IP address (192.168.128.1), and its DHCP capability is disabled. I have a permanently powered up Windows Server 2003 machine with a fixed IP (192.168.128.2) which provides my domain controller, dhcp, and dns. The default gateway for everything is my ADSL modem everything is setup to use the WS2003 machine as the primary DNS with the ADSL modem as Secondary DNS just in case the server goes down (everything includes the server itself). Lastly, just in case it's relevant, I have my DHCP leases set to infinite (or whatever the right term is). Everything is pretty hunky dory. Except, that is, for the fact that my server is ALWAYS on, and it isn't always used, so I'm burning juice that I don't need to - my server burns around 120W which isn't immense but isn't irrelevant either, so I'd like to put it into a stand-by state when it isn't being used (the more standby the better) and then get the clients to wake it up. Am I correct in assuming that this won't work at the moment - A given client would need an IP address to wake the machine up, and it needs to machine to be awake to get an IP - catch 22? Assuming I'm correct, can I move to using my router (which is always on) for DHCP? What impact will this have on DC and DNS? Alternatively, does anyone have a better way for me to achieve this? Can I get the server to wake up when it sees clients look for a DHCP server, etc? Wow, that came out longer than expected! Thanks for your help.

  Read the article

• Why won't my computer go to sleep automatically?

  - by Django Reinhardt

  Windows 8 is set to sleep after 30 mins, and it used to work, but recently it's started refusing to sleep. (I can still manually ask it to go to sleep without any issue.) I was having issues a while ago, but it was with my network adapter. That's since been disabled, so it's definitely not that: I've checked to see what devices are able to wake up my machine, but it only appears to be my mouse: Which is odd, because I haven't recently changed my mouse, and more confusing still: The monitor does go to sleep just fine. If it was actually the mouse keeping my system awake, I'm pretty sure the monitor wouldn't go to sleep. I've checked my Wake Timers, and nothing: I've also checked my existing requests... UPDATE: I found something. What to do with it, I don't know... Note: Even when /requests says that there's "NONE" under every category, my machine still won't sleep(!). In short: How can I tell what's preventing my computer from Sleeping? UPDATE: Ok, so I now have a few more pieces of the puzzle. I came back to my computer and it was ASLEEP! Lawks! It seems that the only times it doesn't sleep is if VLC Player is open, even if a video isn't actually playing. UPDATE UPDATE: Ok, so it won't sleep sometimes when VLC Player ISN'T running, either. Bah!

  Read the article

• IPv6 - Public IPs, private IPs, IPs derived from the MAC address? Confused!

  - by sinni800

  I'm pretty much excited for IPv6 because of the large address room and (potential?) owning of more than one IP, or even tens of IPs (/122 subnet?) Though one magazine has now confused me. In a current issue (no. 3) of "CT", a German computer magazine, I read that when using IPv6 your IP address consists of your MAC address and various other things, and that this address will be public on the web, no matter what access point / LAN you connect to. My knowledge of IP(v6) is in contrary of this. I thought you will normally always have a a local network IP and NAT takes care of your Internet access, and your provider gives the NAT router an IP. I've heard of the 6to4 interface, but does this one give you your own ip in the IPv6 net? Personally I hope it still is through a personal IP space (like 192.168, 127.16-31, 10. in IPv4) in private networks with a NAT going to the Internet. And also I hope that providers will offer subnets to private customers so they don't have to use NAT anymore. Yay for converting your LAN into the WAN and using better security (so Computers from the same subnet still get access rights like normal).

  Read the article

• Adding gcc 4.9 as a compiler option in Xcode

  - by user2129150

  I asked this question on StackOverflow, but it's pretty much stagnant. Sorry if this is considered a repost/double-post. I just installed gcc 4.9 (with C11 support), and want to add it to Xcode 4.6.3's build options as a compiler option. I ran make and make install, and the packages are all there (under /usr/bin/gcc. Running gcc --version confirms that gcc 4.9 is installed rather than an older version. When I go into an existing Xcode project's build settings, the only compiler options available are Apple LLVM compiler 4.2 LLVM GCC 4.2 Other... Clearly, GCC 4.9 would have to be added using the "Other..." option, although I'm not sure how. I've tried inputting the path to gcc (/usr/bin/gcc), although the default value for other isn't a path at all: com.apple.compilers.llvmgcc42. I've also tried following the instructions from the answer to this question as well, but the machine I'm on doesn't have the /Developer directory at all, since I believe Apple integrated the developer tools that required (and created) this directory into Xcode. How do I add gcc 4.9 as a compiler option in Xcode?

  Read the article

< Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >